LUWER ROW 1000PF, 2KV 11 ELECTRICAL SPECIFICATIONS: 1.0 TURNS RATIO P1-Pe-P3> + CJ1-Je2) (P4-P5-P6) +: (J3-J6) 2.0 INDUCTANCE TO (J6,J3) CP3,P2,PL TO (J2,J1 5.0 DC RESISTANCE (J6-J3)=(J1-J2> (P6-P4) (P3-P1 : 1CT +: 14 37% : Le ohms Max. :.7 ohms Max. UPPER RUW ae | JZ a 3 J4 J5 a IG a 7 | a J | 1000PF, 2KV NOTES 1.0 PINS WITHOUT ELE CTRICAL CONNECTION ARE OMITTED. ICT + 1 4 3% 350uUH MIN. @ 01V , 100KHz, 8mA DC Bias : 35SQuUH MIN. @ O1V, 100KHz, 8mA DC Bias 1 Q3uH MAX. @ 1MHz : QSuH MAX. @ 1MHz : 2Spf TYP @ 1MHz 1 2Spf TYP @ 1MHZ 7 ohms Max. InNet Technologies http://www.innet-tech.com Inc. Stewart Connector Systems http://www.stewartconnector.com SHEET 1 of 4 ==" 1-300! 9/026.0 RETURN LOSS: 1MHz TO 30MHz 60MHz TO 80MHz 7.0 VOLTAGE WITHSTAND: (Jl, Jed TO Pl, Ped (J3, J&> TO P3,P6) 8.0 INSERTION LOSS: 100KHz TO 100MHz 9.0 RISE TIME: OUTPUT VOLTAGE = 1 V peak PULSE WIDTH= 112nS 10.0 CROSS TALK: 1MHz TO 100MHz 11.0 COMMON TO COMMON MODE ATTENUATION: 1MHz TO 100MHz 180B MIN, 12dB MIN. 1500 VAC 1500 VAC 11 dB TYP 3.0 nS TYP 3.0 nS TYP 40 dB TYP 350B TYP InNet Technologies Inc. http://www.innet-tech.com Stewart Connector Systems http://www.stewartconnector.com "Soe al ST - 30019 OeSHIELDING: PG4-01 EMI-RFI 2 PIECE SHIELDED, ESD GROUNDED 16 PORTS (8 OVER 8) STACKED JACK MARKING t So 8 8 8 8 8 8 8 Bz eo a o ae ei a oe a =_ alaNahahanhahahsa { BOTTOM *4,606 [116.99] MAX pq 59 [115.04] 148 [3.75] (17) TO HIGHEST POINT OF BEAM 1.063 [27.00] 1.004 [25.50] 023 [0.57] JACK (PCB SURFACE) - SURFACE OF 125 [3.18] +.010 [0.25] (128) NOTES: TOLERANCES COMPLY WITH F.C.C. DIMENSION REQUIREMENTS. DIMENSIONS SHOWN WITH * TO BE CENTRAL ABOUT CENTER LINE. DIMENSIONS SHOWN ARE SUBJECT TO CHANGE WITHOUT NOTICE. PINS NOT ELECTRICALLY CONNECTED MAYBE OMITTED. SEE ELECTRICAL DRAWINGS FOR OMITTED PINS. AVAILABLE WITH: 50 MICRO-INCH SELECTIVE GOLD PLATING 350 [8.89] 100 [2.54] .050 [1.27] TYP dy TOL NONACCUM Tees UN # .035 [.0.89] (8) i 2 } 100 [2.54] TYP -085 [2.11] (9) To TOL NON-ACCUM HIGHEST POINT OF BEAM .040 [1.02] (11) TYPICAL HOLE LAYOUT .243 [6.17] (16 POSITIONS) 4.250 [107.95] 3.700 [93.98] | 3.150 [80.01] | = 2.600 [66.04] | 2.050 [52.07] PIN 1 UPPER ROW 1.500 [38.10] = .950 [24.13 PIN NO. 1 6 .062 [1.57] 400 ! _ PIN NO. 1 BOTTOM ROW 159 # .035 [0.89] 11 HOLES | [10.16] TOP m \ [4.04] 128 ee \ 000 @ | 000 @ 000 000 @ 000 5 0000 ad ooo coco ee coce! eo0 of o.0 0 0 PIN 1 LOWER ROW 2) 2 000 @ | ool 000 000 000 000 000 6 . oo0o0 0000 ooo390o o0o00o0 oo00 0000 foooo oo00 350 [8,89] t _ oo ta [4.57] .180 128 [3.25] @) [4.57] 180 7 Tr? 125 [3.18] . T 110 70} 4.300 [109.22] . P.C.B, RECOMMENDED HOLE LAYOUT M0 [2.79] =| InNet Technologies Inc. N FROM COMPONENT http://www.innettech.com TOLERANCE 003 [0.08] UNLESS OTHERWISE SPECIFIED Stewart Connector Systems http'//www.stewartconnector.com SHEET DRAWING NO, REV. cT720114 3 of 4 SI=30019}" 01 |1300 1200 1100 1000 900 800 700 600 500 400 300 200 100 GRAMS OF FORCE / GROUNDING BEAM GRAMS OF FORCE / GROUNDING BEAM = S + PANEL GROUNDING BEAM DEFLECTION TOP AND SIDE BEAMS S.0,S. = SUGGESTED OPENING SIZE +.005 S.0.S. -.005 -.010 -.015 S | R.010 (4) LL o15 FROM TOP MAX. OF PCB TO BOTTOM OF OPENING ! | 1 . | SUGGESTED PANEL OPENING (N.TS.) CT720114 900 800 700 600 500 400 300 200 100 POINT OF CONTACT WITH PANEL .080 +.010 +.005 S.0.S. .005 PANEL GROUNDING BEAM DEFLECTION BOTTOM BEAMS ONLY S.0,S. = SUGGESTED OPENING SIZE THE SUGGESTED PANEL OPENING IS INTENDED TO GIVE THE USER THE ABILITY TO HAVE REASONABLE JACK / PANEL CLEARANCES YET MAINTAIN RELIABLE GROUNDING CAPABILITY. THESE VARIABLES CAN BE ADJUSTED IN EITHER DIRECTION BUT MAY CARRY SOME CONSEQUENCES IN THE FORM OF LOWER MATING FORCES OR TIGHTER ASSEMBLY TOLERANCES. FORCE VALUES ON THE GRAPH(S) ARE GENERAL AVERAGES TAKEN AT A POINT OF CONTACT SHOWN ABOVE. THE SUGGESTED PANEL OPENING INCLUDES APPROXIMATELY .020 CLEARANCE ON THE TOP AND SIDES, WITH .015 CLEARANCE ON THE BOTTOM. InNet Technologies Inc. http://www.innettech.com Stewart Connector Systems SHEET 4 of 4 http'//www.stewartconnector.com ~O { DRAWING S I _ 2 0 0 | 9