E1UFA20-14.7456M TR RoHS Pb E1U F A 20 -14.7456M TR Series RoHS Compliant (Pb-free) Resistance Welded Short HC-49/US Crystal Packaging Options Tape & Reel Nominal Frequency 14.7456MHz Frequency Tolerance/Stability 30ppm at 25C, 50ppm over -40C to +85C Load Capacitance 20pF Parallel Resonant Mode of Operation AT-Cut Fundamental ELECTRICAL SPECIFICATIONS Nominal Frequency 14.7456MHz Frequency Tolerance/Stability 30ppm at 25C, 50ppm over -40C to +85C Aging at 25C 5ppm/year Maximum Load Capacitance 20pF Parallel Resonant Shunt Capacitance (C0) 7pF Maximum Equivalent Series Resistance 70 Ohms Maximum Mode of Operation AT-Cut Fundamental Drive Level 1mWatt Maximum Storage Temperature Range -40C to +125C Insulation Resistance 500 Megaohms Minimum at 100Vdc ENVIRONMENTAL & MECHANICAL SPECIFICATIONS Fine Leak Test MIL-STD-883, Method 1014 Condition A Gross Leak Test MIL-STD-883, Method 1014 Condition C Lead Integrity MIL-STD-883, Method 2004 Lead Termination Sn 2m - 6m Mechanical Shock MIL-STD-202, Method 213 Condition C Resistance to Soldering Heat MIL-STD-202, Method 210 Resistance to Solvents MIL-STD-202, Method 215 Solderability MIL-STD-883, Method 2003 Temperature Cycling MIL-STD-883, Method 1010 Vibration MIL-STD-883, Method 2007 Condition A MECHANICAL DIMENSIONS (all dimensions in millimeters) LINE MARKING 1 E14.745M E=Ecliptek Designator M=MHz 6.35 MIN DIA 0.457 0.051(X2) 11.18 MAX 4.88 0.20 2.50 MAX 4.70 MAX www.ecliptek.com | Specification Subject to Change Without Notice | Rev E 8/14/2010 | Page 1 of 4 E1UFA20-14.7456M TR Tape & Reel Dimensions Quantity Per Reel: 1,000 Pieces 32.2 MAX 18.0 2.0 18.0 +1.0/-0.5 0.9 MAX 3.81 0.7 12.7 0.3 *Compliant to EIA 468B 56.0 MAX DIA 178 MIN 370 MAX DIA 81.5 MAX 14.0 MIN 38.0 MAX www.ecliptek.com | Specification Subject to Change Without Notice | Rev E 8/14/2010 | Page 2 of 4 E1UFA20-14.7456M TR Recommended Solder Reflow Methods Critical Zone TL to T P Temperature (T) TP Ramp-up Ramp-down TL TS Max TS Min tL t S Preheat t 25C to Peak tP Time (t) High Temperature Solder Bath (Wave Solder) TS MAX to TL (Ramp-up Rate) Preheat - Temperature Minimum (TS MIN) - Temperature Typical (TS TYP) - Temperature Maximum (TS MAX) - Time (tS MIN) Ramp-up Rate (TL to TP) Time Maintained Above: - Temperature (TL) - Time (tL) Peak Temperature (TP) Target Peak Temperature (TP Target) Time within 5C of actual peak (tp) Ramp-down Rate Time 25C to Peak Temperature (t) Moisture Sensitivity Level 3C/second Maximum 150C 175C 200C 60 - 180 Seconds 3C/second Maximum 217C 60 - 150 Seconds 260C Maximum for 10 Seconds Maximum 250C +0/-5C 20 - 40 seconds 6C/second Maximum 8 minutes Maximum Level 1 www.ecliptek.com | Specification Subject to Change Without Notice | Rev E 8/14/2010 | Page 3 of 4 E1UFA20-14.7456M TR Recommended Solder Reflow Methods Critical Zone TL to T P Temperature (T) TP Ramp-up Ramp-down TL TS Max TS Min tL t S Preheat t 25C to Peak tP Time (t) Low Temperature Solder Bath (Wave Solder) TS MAX to TL (Ramp-up Rate) Preheat - Temperature Minimum (TS MIN) - Temperature Typical (TS TYP) - Temperature Maximum (TS MAX) - Time (tS MIN) Ramp-up Rate (TL to TP) Time Maintained Above: - Temperature (TL) - Time (tL) Peak Temperature (TP) Target Peak Temperature (TP Target) Time within 5C of actual peak (tp) Ramp-down Rate Time 25C to Peak Temperature (t) Moisture Sensitivity Level 5C/second Maximum N/A 150C N/A 30 - 60 Seconds 5C/second Maximum 150C 200 Seconds Maximum 245C Maximum 245C Maximum 1 Time / 235C Maximum 2 Times 5 seconds Maximum 1 Time / 15 seconds Maximum 2 Times 5C/second Maximum N/A Level 1 Low Temperature Manual Soldering 185C Maximum for 10 seconds Maximum, 2 times Maximum. High Temperature Manual Soldering 260C Maximum for 5 seconds Maximum, 2 times Maximum. www.ecliptek.com | Specification Subject to Change Without Notice | Rev E 8/14/2010 | Page 4 of 4