CLC1007, CLC2007, CLC4007
Single, Dual, and Quad Low Cost,
High Speed RRO Amplifiers
© 2007-2014 Exar Corporation 1 / 27 exar.com/CLC1007
Rev 1D
FEATURES
260MHz bandwidth
Fully specied at +3V, +5V and ±5V
supplies
Output voltage range:
0.03V to 4.95V; VS = +5; RL = 2kΩ
Input voltage range:
-0.3V to +4.1V; VS = +5
220V/μs slew rate
2.6mA supply current per amplier
±100mA linear output current
±125mA short circuit current
CLC2007 directly replaces LMH6643,
AD8042, AD8052, and AD8092
CLC1007 directly replaces LMH6642,
AD8041, AD8051, and AD8091
APPLICATIONS
A/D driver
Active lters
CCD imaging systems
CD/DVD ROM
Coaxial cable drivers
High capacitive load driver
Portable/battery-powered applications
Twisted pair driver
Telecom and optical terminals
Video driver
General Description
The CLC1007 (single), CLC2007 (dual) and CLC4007(quad) are low cost,
voltage feedback ampliers. These ampliers are designed to operate on
+3V to +5V, or ±5V supplies. The input voltage range extends 300mV below
the negative rail and 0.9V below the positive rail.
The CLC1007, CLC2007, and CLC4007 offer superior dynamic
performance with a 260MHz small signal bandwidth and 220V/μs slew
rate. The combination of low power, high output current drive, and rail-to-
rail performance make these ampliers well suited for battery-powered
communication/computing systems.
The combination of low cost and high performance make the CLC1007,
CLC2007, and CLC4007 suitable for high volume applications in both
consumer and industrial applications such as wireless phones, scanners,
color copiers, and video transmission.
Large Signal Frequency Response
-9
-6
-3
0
3
0.1 110 100 1000
Normalized Gain (dB)
Frequency (MHz)
Vs = +/-5V
Vout = 2Vpp
Vout = 3Vpp
Vout = 4Vpp
Output Voltage Swing vs Competition
-6
-5
-4
-3
-2
-1
0
1
2
3
4
5
6
-5 -4 -3 -2 -1 012345
Output Amplitude (V)
Input Amplitude (V)
RL = 50Ω
VS = ±5V
CLC2007
Competition
Ordering Information - page 26
© 2007-2014 Exar Corporation 2 / 27 exar.com/CLC1007
Rev 1D
CLC1007, CLC2007, CLC4007
Absolute Maximum Ratings
Stresses beyond the limits listed below may cause
permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect
device reliability and lifetime.
VS ................................................................................. 0V to +14V
VIN ............................................................ -VS - 0.5V to +VS +0.5V
Operating Conditions
Supply Voltage Range .................................................2.7 to 12.6V
Operating Temperature Range ...............................-40°C to 125°C
Junction Temperature ...........................................................150°C
Storage Temperature Range ...................................-65°C to 150°C
Lead Temperature (Soldering, 10s) ......................................260°C
Package Thermal Resistance
θJA (TSOT23-5) ................................................................215°C/W
θJA (SOIC-8) .....................................................................150°C/W
θJA (MSOP-8) .................................................................. 200°C/W
θJA (SOIC-14) .................................................................... 90°C/W
θJA (TSSOP-14) ................................................................100°C/W
Package thermal resistance (θJA), JEDEC standard, multi-layer
test boards, still air.
ESD Protection
TSOT-5 (HBM) ..........................................................................1kV
SOIC-8 (HBM) ..........................................................................1kV
TSOT-5 (CDM) .......................................................................... 2kV
SOIC-8 (CDM) ..........................................................................2kV
ESD Rating for HBM (Human Body Model) and CDM (Charged
Device Model).
© 2007-2014 Exar Corporation 3 / 27 exar.com/CLC1007
Rev 1D
CLC1007, CLC2007, CLC4007
Electrical Characteristics at +3V
TA = 25°C, VS = +3V, Rf = 1.5kΩ, RL = 2kΩ to VS/2; G = 2; unless otherwise noted.
Symbol Parameter Conditions Min Ty p Max Units
Frequency Domain Response
GBWP -3dB Gain Bandwidth Product G = +11, VOUT = 0.2Vpp 90 MHz
UGBW Unity Gain Bandwidth VOUT = 0.2Vpp, RF = 0 245 MHz
BWSS -3dB Bandwidth VOUT = 0.2Vpp 85 MHz
f0.1dB 0.1dB Gain Flatness VOUT = 0.2Vpp, RL = 150Ω 16 MHz
BWLS Large Signal Bandwidth VOUT = 2Vpp 55 MHz
DG Differential Gain DC-coupled Output 0.03 %
AC-coupled Output 0.04 %
DP Differential Phase DC-coupled Output 0.03 °
AC-coupled Output 0.06 °
Time Domain
tR, tFRise and Fall Time VOUT = 0.2V step; (10% to 90%) 5 ns
tSSettling Time to 0.1% VOUT = 1V step 25 ns
OS Overshoot VOUT = 0.2V step 8 %
SR Slew Rate G = -1, 2V step 175 V/μs
Distortion/Noise Response
THD Total Harmonic Distortion 1MHz, VOUT = 1Vpp 75 dBc
enInput Voltage Noise >50kHz 16 nV/√Hz
XTALK Crosstalk f = 5MHz 58 dB
DC Performance
VIO Input Offset Voltage 0.5 mV
dVIO Average Drift 5 μV/°C
IBInput Bias Current 1. 4 μA
dIBAverage Drift 2 nA/°C
IOS Input Offset Current 0.05 μA
PSRR Power Supply Rejection Ratio DC 102 dB
AOL Open Loop Gain RL = 2kΩ 92 dB
ISSupply Current per channel 2.6 mA
Input Characteristics
CIN Input Capacitance 0.5 pF
CMIR Common Mode Input Range -0.3 to
2.1 V
CMRR Common Mode Rejection Ratio DC, VCM = 0 to 1.5V 100 dB
Output Characteristics
VOUT Output Swing
RL = 150Ω 0.3 to
2.75 V
RL = 2kΩ 0.02 to
2.96 V
IOUT Output Current ±100 mA
ISC Short Circuit Current VOUT = VS / 2 ±125 V
VSPower Supply Operating Range 2.7 to
12.6 V
© 2007-2014 Exar Corporation 4 / 27 exar.com/CLC1007
Rev 1D
CLC1007, CLC2007, CLC4007
Electrical Characteristics at +5V
TA = 25°C, VS = +5V, Rf = 1.5kΩ, RL = 2kΩ to VS/2; G = 2; unless otherwise noted.
Symbol Parameter Conditions Min Ty p Max Units
Frequency Domain Response
GBWP -3dB Gain Bandwidth Product G = +11, VOUT = 0.2Vpp 95 MHz
UGBW Unity Gain Bandwidth VOUT = 0.2Vpp, RF = 0 250 MHz
BWSS -3dB Bandwidth VOUT = 0.2Vpp 85 MHz
f0.1dB 0.1dB Gain Flatness VOUT = 0.2Vpp, RL = 150Ω 35 MHz
BWLS Large Signal Bandwidth VOUT = 2Vpp 65 MHz
DG Differential Gain DC-coupled Output 0.03 %
AC-coupled Output 0.04 %
DP Differential Phase DC-coupled Output 0.03 °
AC-coupled Output 0.06 °
Time Domain
tR, tFRise and Fall Time VOUT = 0.2V step 5 ns
tSSettling Time to 0.1% VOUT = 2V step 25 ns
OS Overshoot VOUT = 0.2V step 5 %
SR Slew Rate G = -1, 4V step 220 V/μs
Distortion/Noise Response
THD Total Harmonic Distortion 1MHz, VOUT = 2Vpp -75 dBc
enInput Voltage Noise >50kHz 16 nV/√Hz
XTALK Crosstalk f = 5MHz 58 dB
DC Performance
VIO Input Offset Voltage -7 0.5 7 mV
dVIO Average Drift 5 μV/°C
IBInput Bias Current -2 1. 4 2 μA
dIBAverage Drift 2 nA/°C
IOS Input Offset Current -0.75 0.05 0.75 μA
PSRR Power Supply Rejection Ratio DC 80 102 dB
AOL Open Loop Gain RL = 2kΩ 80 92 dB
ISSupply Current per channel 2.6 4 mA
Input Characteristics
CIN Input Capacitance 0.5 pF
CMIR Common Mode Input Range -0.3 to
4.1 V
CMRR Common Mode Rejection Ratio DC, VCM = 0 to 3.5V 75 100 dB
Output Characteristics
VOUT Output Swing
RL = 150Ω 0.35 0.1 to
4.9 4.65 V
RL = 2kΩ 0.03 to
4.95 V
IOUT Output Current ±100 mA
ISC Short Circuit Current VOUT = VS / 2 ±125 V
VSPower Supply Operating Range 2.7 to
12.6 V
© 2007-2014 Exar Corporation 5 / 27 exar.com/CLC1007
Rev 1D
CLC1007, CLC2007, CLC4007
Electrical Characteristics at ±5V
TA = 25°C, VS = ±5V, Rf = 1.5kΩ, RL = 2kΩ to GND; G = 2; unless otherwise noted.
Symbol Parameter Conditions Min Ty p Max Units
Frequency Domain Response
GBWP -3dB Gain Bandwidth Product G = +11, VOUT = 0.2Vpp 90 MHz
UGBW Unity Gain Bandwidth VOUT = 0.2Vpp, RF = 0 260 MHz
BWSS -3dB Bandwidth VOUT = 0.2Vpp 85 MHz
f0.1dB 0.1dB Gain Flatness VOUT = 0.2Vpp, RL = 150Ω 22 MHz
BWLS Large Signal Bandwidth VOUT = 2Vpp 65 MHz
DG Differential Gain DC-coupled Output 0.03 %
AC-coupled Output 0.04 %
DP Differential Phase DC-coupled Output 0.03 °
AC-coupled Output 0.06 °
Time Domain
tR, tFRise and Fall Time VOUT = 0.2V step 5 ns
tSSettling Time to 0.1% VOUT = 2V step, RL = 100Ω 25 ns
OS Overshoot VOUT = 0.2V step 5 %
SR Slew Rate G = -1, 5V step 225 V/μs
Distortion/Noise Response
THD Total Harmonic Distortion 1MHz, VOUT = 2Vpp 76 dBc
enInput Voltage Noise >50kHz 16 nV/√Hz
XTALK Crosstalk f = 5MHz 58 dB
DC Performance
VIO Input Offset Voltage 0.5 mV
dVIO Average Drift 5 μV/°C
IBInput Bias Current 1. 3 μA
dIBAverage Drift 2 nA/°C
IOS Input Offset Current 0.04 μA
PSRR Power Supply Rejection Ratio DC 102 dB
AOL Open Loop Gain RL = 2kΩ 92 dB
ISSupply Current per channel 2.6 mA
Input Characteristics
CIN Input Capacitance 0.5 pF
CMIR Common Mode Input Range -5.3 to
4.1 V
CMRR Common Mode Rejection Ratio DC, VCM = -5 to 3.5V 100 dB
Output Characteristics
VOUT Output Swing
RL = 150Ω -4.8 to
4.8 V
RL = 2kΩ -4.95 to
4.93 V
IOUT Output Current ±100 mA
ISC Short Circuit Current VOUT = VS / 2 ±125 V
VSPower Supply Operating Range 2.7 to
12.6 V
© 2007-2014 Exar Corporation 6 / 27 exar.com/CLC1007
Rev 1D
CLC1007, CLC2007, CLC4007
SOIC-8
Pin No. Pin Name Description
1 NC No Connect
2 -IN Negative input
3 +IN Positive input
4 -VSNegative supply
5 NC No Connect
6 OUT Output
7 +VSPositive supply
8 NC No Connect
SOIC-8
-
+
1
2
3
4
NC
-IN
+IN
-Vs
NC
+Vs
OUT
NC
8
7
6
5
CLC1007 Pin Assignments
TSOT-5
Pin No. Pin Name Description
1 OUT Output
2 -VSNegative supply
3 +IN Positive input
4 -IN Negative input
5 +VSPositive supply
CLC1007 Pin Congurations
TSOT-5
-
+
2
3
5
4
+IN
+Vs
-IN
1
-Vs
OUT
CLC2007 Pin Assignments
SOIC-8 / MSOP-8
Pin No. Pin Name Description
1 OUT1 Output, channel 1
2 -IN1 Negative input, channel 1
3 +IN1 Positive input, channel 1
4 -VSNegative supply
5 +IN2 Positive input, channel 2
6 -IN2 Negative input, channel 2
7 OUT2 Output, channel 2
8 +VSPositive supply
CLC2007 Pin Conguration
SOIC-8 / MSOP-8
-
+
-
+
1
2
3
4
OUT1
-IN1
+IN1
-Vs
+Vs
OUT2
-IN2
+IN2
8
7
6
5
© 2007-2014 Exar Corporation 7 / 27 exar.com/CLC1007
Rev 1D
CLC1007, CLC2007, CLC4007
CLC4007 Pin Assignments
SOIC-14 / TSSOP-14
Pin No. Pin Name Description
1 OUT1 Output, channel 1
2 -IN1 Negative input, channel 1
3 +IN1 Positive input, channel 1
4 +VSPositive supply
5 +IN2 Positive input, channel 2
6 -IN2 Negative input, channel 2
7 OUT2 Output, channel 2
8 OUT3 Output, channel 3
9 -IN3 Negative input, channel 3
10 +IN3 Positive input, channel 3
11 -VSNegative supply
12 +IN4 Positive input, channel 4
13 -IN4 Negative input, channel 4
14 OUT4 Output, channel 4
CLC4007 Pin Conguration
SOIC-14 / TSSOP-14
2
3
4 11
12
13
14
-IN4
+IN1
OUT4
+IN4
1
-IN1
OUT1
5
6
7
OUT2
-IN2
+IN2
8
9
10
+IN3
-IN3
OUT3
+VS-VS
© 2007-2014 Exar Corporation 8 / 27 exar.com/CLC1007
Rev 1D
CLC1007, CLC2007, CLC4007
Typical Performance Characteristics at +3V
TA = 25°C, VS = +3V, RL = 2kΩ to VS/2, G = +2, RF = 1.5kΩ; unless otherwise noted.
Large Signal Frequency Response -3dB BW vs Output Voltage
Frequency Response vs CL Frequency Response vs RL
Non-Inverting Frequency Response Inverting Frequency Response
-9
-6
-3
0
3
0.1 110 100 1000
Normalized Gain (dB)
Frequency (MHz)
G = +1, RF = 0Ω
G = +5
G = +10
Vs = +3V, VOUT = 0.2Vpp
G = +2
-9
-6
-3
0
3
0.1 110 100 1000
Normalized Gain (dB)
Frequency (MHz)
G = -1
G = -5
G = -10
Vs = +3V, VOUT = 0.2Vpp
G = -2
-9
-6
-3
0
3
0.1 110 100 1000
Normalized Gain (dB)
Frequency (MHz)
CL = 22pF
No RS
Vs = +3V, VOUT = 0.2Vpp CL = 47pF
RS = 20Ω
CL = 100pF
RS = 18Ω
CL = 492pF
RS = 7.5Ω
CL = 1000pF
RS = 4.3Ω
-9
-6
-3
0
3
0.1 110 100 1000
Normalized Gain (dB)
Frequency (MHz)
RL = 150Ω
Vs = +3V, VOUT = 0.2Vpp
RL = 500Ω
RL = 1KΩRL = 5KΩ
-9
-6
-3
0
3
0.1 110 100 1000
Normalized Gain (dB)
Frequency (MHz)
Vs = +3V
Vout = 1Vpp
Vout = 2Vpp
20
30
40
50
60
70
80
90
100
110
120
00.5 11.5 2
-3dB Bandwidth (MHz)
Output Voltage (Vpp)
RL = 150Ω
Vs = +3V
RL = 2KΩ
© 2007-2014 Exar Corporation 9 / 27 exar.com/CLC1007
Rev 1D
CLC1007, CLC2007, CLC4007
Typical Performance Characteristics at +3V
TA = 25°C, VS = +3V, RL = 2kΩ to VS/2, G = +2, RF = 1.5kΩ; unless otherwise noted.
3rd Harmonic Distortion vs VO over Frequency Non-Inverting Small Signal Pulse Response
3rd Harmonic Distortion vs RL over Frequency 2nd Harmonic Distortion vs VO over Frequency
Input Voltage Noise vs Frequency 2nd Harmonic Distortion vs RL over Frequency
15
20
25
30
35
40
45
50
55
0.1 110 100 1000
Input Voltage Noise (nV/√Hz)
Frequency (KHz)
-100
-90
-80
-70
-60
-50
-40
-30
-20
0 5 10 15 20
Distortion (dBc)
Frequency (MHz)
Hd2_RL= 2KΩ
Vs= +3V_VOUT = 1Vpp
Hd2_RL= 150Ω
-100
-90
-80
-70
-60
-50
-40
-30
-20
0 5 10 15 20
Distortion (dBc)
Frequency (MHz)
Hd3_RL= 150Ω
Vs= +3V_VOUT = 1Vpp
Hd3_RL= 2KΩ
-100
-90
-80
-70
-60
-50
-40
0.5 11.5 2
Distortion (dBc)
Output Amplitude (Vpp)
1MHz
Vs= +3V_RL = 150Ω
2MHz
5MHz
-100
-90
-80
-70
-60
-50
-40
0.5 11.5 2
Distortion (dBc)
Output Amplitude (Vpp)
1MHz
Vs= +3V_RL = 150Ω
2MHz
5MHz
1.3
1.4
1.5
1.6
1.7
050 100 150 200
Voltage (V)
Time (ns)
Vs= +3V
© 2007-2014 Exar Corporation 10 / 27 exar.com/CLC1007
Rev 1D
CLC1007, CLC2007, CLC4007
Typical Performance Characteristics at +3V
TA = 25°C, VS = +3V, RL = 2kΩ to VS/2, G = +2, RF = 1.5kΩ; unless otherwise noted.
Differential Gain & Phase_DC Coupled Differential Gain & Phase_AC Coupled
Non-Inverting Large Signal Pulse Response Crosstalk vs Frequency (CLC2007)
0
0.5
1
1.5
2
2.5
3
050 100 150 200
Voltage (V)
Time (ns)
Vs= +3V -100
-90
-80
-70
-60
-50
-40
0.01 0.1 110
Crosstalk (dB)
Frequency (MHz)
Vs = +3V, RL = 150Ω, VOUT = 2Vpp
© 2007-2014 Exar Corporation 11 / 27 exar.com/CLC1007
Rev 1D
CLC1007, CLC2007, CLC4007
Typical Performance Characteristics at +5V
TA = 25°C, VS = +5V, RL = 2kΩ to VS/2, G = +2, RF = 1.5kΩ; unless otherwise noted.
Large Signal Frequency Response -3dB BW vs Output Voltage
Frequency Response vs CL Frequency Response vs RL
Non-Inverting Frequency Response Inverting Frequency Response
-9
-6
-3
0
3
0.1 110 100 1000
Normalized Gain (dB)
Frequency (MHz)
G = +1, RF = 0Ω
G = +5
G = +10
Vs = +5V, VOUT = 0.2Vpp
G = +2
-9
-6
-3
0
3
0.1 110 100 1000
Normalized Gain (dB)
Frequency (MHz)
G = -1
G = -5
G = -10
Vs = +5V, VOUT = 0.2Vpp
G = -2
-9
-6
-3
0
3
0.1 110 100 1000
Normalized Gain (dB)
Frequency (MHz)
CL = 22pF
No RS
Vs = +5V, VOUT = 0.2Vpp CL = 47pF
RS = 20Ω
CL = 100pF
RS = 18Ω
CL = 492pF
RS = 7.5Ω
CL = 1000pF
RS = 4.3Ω
-9
-6
-3
0
3
0.1 110 100 1000
Normalized Gain (dB)
Frequency (MHz)
RL = 150Ω
Vs = +5V, VOUT = 0.2Vpp
RL = 500Ω
RL = 1KΩRL = 5KΩ
-9
-6
-3
0
3
0.1 110 100 1000
Normalized Gain (dB)
Frequency (MHz)
Vs = 5V
Vout = 1Vpp
Vout = 2Vpp
Vout = 3Vpp
20
30
40
50
60
70
80
90
100
110
00.5 11.5 22.5 3
-3dB Bandwidth (MHz)
Output Voltage (Vpp)
RL = 150Ω
Vs = +5V
RL = 2KΩ
© 2007-2014 Exar Corporation 12 / 27 exar.com/CLC1007
Rev 1D
CLC1007, CLC2007, CLC4007
Typical Performance Characteristics at +5V
TA = 25°C, VS = +5V, RL = 2kΩ to VS/2, G = +2, RF = 1.5kΩ; unless otherwise noted.
3rd Harmonic Distortion vs VO over Frequency Non-Inverting Small Signal Pulse Response
3rd Harmonic Distortion vs RL over Frequency 2nd Harmonic Distortion vs VO over Frequency
Input Voltage Noise vs Frequency 2nd Harmonic Distortion vs RL over Frequency
15
20
25
30
35
40
45
50
55
0.1 110 100 1000
Input Voltage Noise (nV/√Hz)
Frequency (KHz)
-100
-90
-80
-70
-60
-50
-40
-30
-20
0 5 10 15 20
Distortion (dBc)
Frequency (MHz)
Hd2_RL= 2KΩ
Vs= +5V_VOUT = 2Vpp
Hd2_RL= 150Ω
-100
-90
-80
-70
-60
-50
-40
-30
-20
0 5 10 15 20
Distortion (dBc)
Frequency (MHz)
Hd3_RL= 150Ω
Vs= +/-5V_VOUT = 2Vpp
Hd3_RL= 2kΩ
Vs= +5V_VOUT = 2Vpp
-100
-90
-80
-70
-60
-50
-40
0.5 11.5 2
Distortion (dBc)
Output Amplitude (Vpp)
1MHz
Vs= +5V_RL = 150Ω
2MHz
5MHz
-100
-90
-80
-70
-60
-50
-40
0.5 11.5 2
Distortion (dBc)
Output Amplitude (Vpp)
1MHz
Vs= +5V_RL = 150Ω
2MHz
5MHz
Vs= +5V_RL = 150Ω
2.3
2.4
2.5
2.6
2.7
050 100 150 200
Voltage (V)
Time (ns)
Vs= +5V
© 2007-2014 Exar Corporation 13 / 27 exar.com/CLC1007
Rev 1D
CLC1007, CLC2007, CLC4007
Typical Performance Characteristics at +5V
TA = 25°C, VS = +5V, RL = 2kΩ to VS/2, G = +2, RF = 1.5kΩ; unless otherwise noted.
Differential Gain & Phase_DC Coupled Differential Gain & Phase_AC Coupled
Non-Inverting Large Signal Pulse Response Crosstalk vs Frequency (CLC2007)
0
1
2
3
4
5
050 100 150 200
Voltage (V)
Time (ns)
Vs= +5V -100
-90
-80
-70
-60
-50
-40
0.01 0.1 110
Crosstalk (dB)
Frequency (MHz)
Vs = +5V, RL = 150Ω, VOUT = 2Vpp
© 2007-2014 Exar Corporation 14 / 27 exar.com/CLC1007
Rev 1D
CLC1007, CLC2007, CLC4007
Typical Performance Characteristics at ±5V
TA = 25°C, VS = ±5V, RL = 2kΩ to GND, G = +2, RF = 1.5kΩ; unless otherwise noted.
Large Signal Frequency Response -3dB BW vs Output Voltage
Frequency Response vs CL Frequency Response vs RL
Non-Inverting Frequency Response Inverting Frequency Response
-9
-6
-3
0
3
0.1 110 100 1000
Normalized Gain (dB)
Frequency (MHz)
G = +1, RF = 0Ω
G = +5
G = +10
Vs = +/-5V, VOUT = 0.2Vpp
G = +2
-9
-6
-3
0
3
0.1 110 100 1000
Normalized Gain (dB)
Frequency (MHz)
G = -1
G = -5
G = -10
Vs = +/-5V, VOUT = 0.2Vpp
G = -2
-9
-6
-3
0
3
0.1 110 100 1000
Normalized Gain (dB)
Frequency (MHz)
CL = 22pF
No RS
Vs = +/-5V, VOUT = 0.2Vpp CL = 47pF
RS = 15Ω
CL = 100pF
RS = 15Ω
CL = 492pF
RS = 6.5Ω
CL = 1000pF
RS = 4.3Ω
-9
-6
-3
0
3
0.1 110 100 1000
Normalized Gain (dB)
Frequency (MHz)
RL = 150Ω
Vs = +/-5V, VOUT = 0.2Vpp
RL = 500Ω
RL = 1KΩRL = 5KΩ
-9
-6
-3
0
3
0.1 110 100 1000
Normalized Gain (dB)
Frequency (MHz)
Vs = +/-5V
Vout = 2Vpp
Vout = 3Vpp
Vout = 4Vpp
20
30
40
50
60
70
80
90
100
110
00.5 11.5 22.5 33.5 4
-3dB Bandwidth (MHz)
Output Voltage (Vpp)
RL = 150Ω
Vs = +/-5V
RL = 2KΩ
© 2007-2014 Exar Corporation 15 / 27 exar.com/CLC1007
Rev 1D
CLC1007, CLC2007, CLC4007
Typical Performance Characteristics at ±5V
TA = 25°C, VS = ±5V, RL = 2kΩ to GND, G = +2, RF = 1.5kΩ; unless otherwise noted.
3rd Harmonic Distortion vs VO over Frequency Non-Inverting Small Signal Pulse Response
3rd Harmonic Distortion vs RL over Frequency 2nd Harmonic Distortion vs VO over Frequency
Input Voltage Noise vs Frequency 2nd Harmonic Distortion vs RL over Frequency
15
20
25
30
35
40
45
50
55
0.1 110 100 1000
Input Voltage Noise (nV/√Hz)
Frequency (KHz)
-100
-90
-80
-70
-60
-50
-40
-30
-20
0 5 10 15 20
Distortion (dBc)
Frequency (MHz)
Hd2_RL= 2KΩ
Vs= +/-5V_VOUT = 2Vpp
Hd2_RL= 150Ω
-100
-90
-80
-70
-60
-50
-40
-30
-20
0 5 10 15 20
Distortion (dBc)
Frequency (MHz)
Hd3_RL= 150Ω
Vs= +/-5V_VOUT = 2Vpp
Hd3_RL= 2kΩ
Vs= +/-5V_VOUT = 2Vpp
-100
-90
-80
-70
-60
-50
-40
0.5 11.5 2
Distortion (dBc)
Output Amplitude (Vpp)
1MHz
Vs= +/-5V_RL = 150Ω
2MHz
5MHz
-100
-90
-80
-70
-60
-50
-40
0.5 11.5 2
Distortion (dBc)
Output Amplitude (Vpp)
1MHz
2MHz
5MHz
Vs= +/-5V_RL = 150Ω
-0.25
-0.2
-0.15
-0.1
-0.05
0
0.05
0.1
0.15
0.2
0.25
050 100 150 200
Voltage (V)
Time (ns)
Vs= +/-5V
© 2007-2014 Exar Corporation 16 / 27 exar.com/CLC1007
Rev 1D
CLC1007, CLC2007, CLC4007
Typical Performance Characteristics at ±5V
TA = 25°C, VS = ±5V, RL = 2kΩ to GND, G = +2, RF = 1.5kΩ; unless otherwise noted.
Differential Gain & Phase_DC Coupled Differential Gain & Phase_AC Coupled
Non-Inverting Large Signal Pulse Response Crosstalk vs Frequency (CLC2007)
-3
-2
-1
0
1
2
3
050 100 150 200
Voltage (V)
Time (ns)
Vs= +/-5V -100
-90
-80
-70
-60
-50
-40
0.01 0.1 110
Crosstalk (dB)
Frequency (MHz)
Vs = +/-5V, RL = 150Ω, VOUT = 2Vpp
© 2007-2014 Exar Corporation 17 / 27 exar.com/CLC1007
Rev 1D
CLC1007, CLC2007, CLC4007
Application Information
General Description
The CLC1007, CLC2007, and CLC4007 are single supply,
general purpose, voltage-feedback ampliers fabricated on
a complementary bipolar process using a patent pending
topography. They feature a rail-to-rail output stage and is
unity gain stable. Both gain bandwidth and slew rate are
insensitive to temperature.
The common mode input range extends to 300mV below
ground and to 0.9V below Vs. Exceeding these values will
not cause phase reversal. However, if the input voltage
exceeds the rails by more than 0.5V, the input ESD devices
will begin to conduct. The output will stay at the rail during
this overdrive condition.
The design is short circuit protected and offers “soft”
saturation protection that improves recovery time.
Figures 1, 2, and 3 illustrate typical circuit congurations for
non-inverting, inverting, and unity gain topologies for dual
supply applications. They show the recommended bypass
capacitor values and overall closed loop gain equations. Figure
4 shows the typical non-inverting gain circuit for single supply
applications.
+
-
Rf
0.1μF
6.8μF
Output
G = 1 + (Rf/Rg)
Input
+Vs
-Vs
Rg
0.1μF
6.8μF
RL
Figure 1: Typical Non-Inverting Gain Circuit
+
-
Rf
0.1μF
6.8μF
Output
G = - (Rf/Rg)
For optimum input offset
voltage set R1 = Rf || Rg
Input
+Vs
-Vs
0.1μF
6.8μF
RL
Rg
R1
Figure 2: Typical Inverting Gain Circuit
+
-
0.1μF
6.8μF
Output
G = 1
Input
+Vs
-Vs
0.1μF
6.8μF
RL
Figure 3: Unity Gain Circuit
+
-Rf
0.1μF
6.8μF
Out
In
+Vs
+
Rg
Figure 4: Single Supply Non-Inverting Gain Circuit
Overdrive Recovery
For an amplier, an overdrive condition occurs when the
output and/or input ranges are exceeded. The recovery time
varies based on whether the input or output is overdriven
and by how much the ranges are exceeded. The CLC1007,
CLC2007, and CLC4007 will typically recover in less than
20ns from an overdrive condition. Figure 5 shows the
CLC2007 in an overdriven condition.
-6
-4
-2
0
2
4
6
0100 200 300 400 500 600 700 800 900 1,000
Voltage (V)
Time (ns)
Vs= +/-5V_RL=2K_AV=+5
INPUT
OUTPUT
Figure 5: Overdrive Recovery
© 2007-2014 Exar Corporation 18 / 27 exar.com/CLC1007
Rev 1D
CLC1007, CLC2007, CLC4007
Power Dissipation
Power dissipation should not be a factor when operating
under the stated 2kΩ load condition. However, applications
with low impedance, DC coupled loads should be analyzed
to ensure that maximum allowed junction temperature is
not exceeded. Guidelines listed below can be used to verify
that the particular application will not cause the device to
operate beyond it’s intended operating range.
Maximum power levels are set by the absolute maximum
junction rating of 170°C. To calculate the junction
temperature, the package thermal resistance value ThetaJA
(θJA) is used along with the total die power dissipation.
TJunction = TAmbient + (θJA × PD)
Where TAmbient is the temperature of the working
environment.
In order to determine PD, the power dissipated in the load
needs to be subtracted from the total power delivered by the
supplies.
PD = Psupply - Pload
Supply power is calculated by the standard power equation.
Psupply = Vsupply × IRMSsupply
Vsupply = VS+ - VS-
Power delivered to a purely resistive load is:
Pload = ((Vload)RMS2)/Rloadeff
The effective load resistor (Rloadeff) will need to include the
effect of the feedback network. For instance,
Rloadeff in Figure 3 would be calculated as:
RL || (Rf + Rg)
These measurements are basic and are relatively easy to
perform with standard lab equipment. For design purposes
however, prior knowledge of actual signal levels and load
impedance is needed to determine the dissipated power.
Here, PD can be found from
PD = PQuiescent + PDynamic - Pload
Quiescent power can be derived from the specied IS values
along with known supply voltage, Vsupply. Load power can
be calculated as above with the desired signal amplitudes
using:
(Vload)RMS = Vpeak / √2
( Iload)RMS = ( Vload)RMS / Rloadeff
The dynamic power is focused primarily within the output
stage driving the load. This value can be calculated as:
PDynamic = (VS+ - Vload)RMS × ( Iload)RMS
Assuming the load is referenced in the middle of the power
rails or Vsupply/2.
The CLC1007 is short circuit protected. However, this may
not guarantee that the maximum junction temperature
(+150°C) is not exceeded under all conditions. Figure 6
shows the maximum safe power dissipation in the package
vs. the ambient temperature for the packages available.
0
0.5
1
1.5
2
2.5
-40 -20 020 40 60 80 100 120
Maximum Power Dissipation (W)
Ambient Temperature (°C)
MSOP-8
SOIC-8
TSSOP-14
TSOT-5
SOIC-14
Figure 6. Maximum Power Derating
Driving Capacitive Loads
Increased phase delay at the output due to capacitive loading
can cause ringing, peaking in the frequency response, and
possible unstable behavior. Use a series resistance, RS,
between the amplier and the load to help improve stability
and settling performance. Refer to Figure 7.
+
-
Rf
Input
Output
Rg
Rs
CLRL
Figure 7. Addition of RS for Driving Capacitive Loads
Table 1 provides the recommended RS for various capacitive
loads. The recommended RS values result in approximately
<1dB peaking in the frequency response.
CL (pF) RS (Ω) -3dB BW (MHz)
22pF 0 118
47pF 15 112
100pF 15 91
492pF 6.5 59
Table 1: Recommended RS vs. CL
© 2007-2014 Exar Corporation 19 / 27 exar.com/CLC1007
Rev 1D
CLC1007, CLC2007, CLC4007
For a given load capacitance, adjust RS to optimize the
tradeoff between settling time and bandwidth. In general,
reducing RS will increase bandwidth at the expense of
additional overshoot and ringing.
Layout Considerations
General layout and supply bypassing play major roles in
high frequency performance. Exar has evaluation boards to
use as a guide for high frequency layout and as an aid in
device testing and characterization. Follow the steps below
as a basis for high frequency layout:
Include 6.8µF and 0.1µF ceramic capacitors for power supply
decoupling
Place the 6.8µF capacitor within 0.75 inches of the power pin
Place the 0.1µF capacitor within 0.1 inches of the power pin
Remove the ground plane under and around the part,
especially near the input and output pins to reduce parasitic
capacitance
Minimize all trace lengths to reduce series inductances
Refer to the evaluation board layouts below for more
information.
Evaluation Board Information
The following evaluation boards are available to aid in the
testing and layout of these devices:
Evaluation Board # Products
CEB002 CLC1007 in TSOT
CEB003 CLC1007 in SOIC
CEB006 CLC2007 in SOIC
CEB010 CLC2007 in MSOP
CEB018 CLC4007 in SOIC
CEB019 CLC4007 in TSSOP
Evaluation Board Schematics
Evaluation board schematics and layouts are shown in
Figures 8-20. These evaluation boards are built for dual-
supply operation. Follow these steps to use the board in a
single-supply application:
1. Short -VS to ground.
2. Use C3 and C4, if the -VS pin of the amplier is not
directly connected to the ground plane.
Figure 8. CEB002 & CEB003 Schematic
Figure 9. CEB002 Top View
© 2007-2014 Exar Corporation 26 / 27 exar.com/CLC1007
Rev 1D
CLC1007, CLC2007, CLC4007
Ordering Information
Part Number Package Green Operating Temperature Range Packaging
CLC1007 Ordering Information
CLC1007IST5X TSOT-5 Ye s -40°C to +125°C Tape & Reel
CLC1007IST5MTR TSOT-5 Ye s -40°C to +125°C Mini Tape & Reel
CLC1007IST5EVB Evaluation Board N/A N/A N/A
CLC1007ISO8X SOIC-8 Ye s -40°C to +125°C Tape & Reel
CLC1007ISO8MTR SOIC-8 Ye s -40°C to +125°C Mini Tape & Reel
CLC1007ISO8EVB Evaluation Board N/A N/A N/A
CLC2007 Ordering Information
CLC2007ISO8X SOIC-8 Ye s -40°C to +125°C Tape & Reel
CLC2007ISO8MTR SOIC-8 Ye s -40°C to +125°C Mini Tape & Reel
CLC2007ISO8EVB Evaluation Board N/A N/A N/A
CLC2007IMP8X MSOP-8 Ye s -40°C to +125°C Tape & Reel
CLC2007IMP8MTR MSOP-8 Ye s -40°C to +125°C Mini Tape & Reel
CLC2007IMP8EVB Evaluation Board N/A N/A N/A
CLC4007 Ordering Information
CLC4007ITP14X TSSOP-14 Ye s -40°C to +125°C Tape & Reel
CLC4007ITP14MTR TSSOP-14 Ye s -40°C to +125°C Mini Tape & Reel
CLC4007ITP14EVB Evaluation Board N/A N/A N/A
CLC4007ISO14X SOIC-14 Ye s -40°C to +125°C Tape & Reel
CLC4007ISO14MTR SOIC-14 Ye s -40°C to +125°C Mini Tape & Reel
CLC4007ISO14EVB Evaluation Board N/A N/A N/A
Moisture sensitivity level for all parts is MSL-1.
For Further Assistance:
Email: CustomerSupport@exar.com or HPATechSupport@exar.com
Exar Technical Documentation: http://www.exar.com/techdoc/
Exar Corporation Headquarters and Sales Offices
48760 Kato Road Tel.: +1 (510) 668-7000
Fremont, CA 94538 - USA Fax: +1 (510) 668-7001
NOTICE
EXAR Corporation reserves the right to make changes to the products contained in this publication in order to improve design, performance or reliability. EXAR Corporation
assumes no responsibility for the use of any circuits described herein, conveys no license under any patent or other right, and makes no representation that the circuits are free
of patent infringement. Charts and schedules contained here in are only for illustration purposes and may vary depending upon a user’s specic application. While the information
in this publication has been carefully checked; no responsibility, however, is assumed for inaccuracies.
EXAR Corporation does not recommend the use of any of its products in life support applications where the failure or malfunction of the product can reasonably be expected
to cause failure of the life support system or to signicantly affect its safety or effectiveness. Products are not authorized for use in such applications unless EXAR Corporation
receives, in writing, assurances to its satisfaction that: (a) the risk of injury or damage has been minimized; (b) the user assumes all such risks; (c) potential liability of EXAR
Corporation is adequately protected under the circumstances.
Reproduction, in part or whole, without the prior written consent of EXAR Corporation is prohibited.
© 2007-2014 Exar Corporation 27 / 27 exar.com/CLC1007
Rev 1D
CLC1007, CLC2007, CLC4007
Revision History
Revision Date Description
1D (ECN 1451-07) December
2014
Reformat into Exar data sheet template. Updated ordering information table to include MTR and EVB
part numbers. Increased “I” temperature range from +85 to +125°C. Removed “A” temp grade parts,
since “I” is now equivalent. Updated thermal resistance numbers and package outline drawings.
