T PL IA N M CO *R oH S Features RoHS compliant* Linear or audio taper versions Space saving design Wide range of resistance values PC pin or solder lug terminals Metric shaft and bushing option Mounting brackets available PC - "Slimline" 22 mm Square Single Turn Panel Control Electrical Characteristics Standard Resistance Range Linear Tapers.................................................................................................................................................... 500 ohms to 1 megohm Audio Tapers ...................................................................................................................................................1 K ohms to 500 K ohms Total Resistance Tolerance ................................................................................................................................................................ 20 % Independent Linearity .......................................................................................................................................................................... 5 % Absolute Minimum Resistance ........................................................................................................................................ 5 ohms maximum Effective Electrical Angle .............................................................................................................................................................270 5 Contact Resistance Variation ...................................................................................................................................7 % of total resistance Dielectric Withstanding Voltage (MIL-STD-202, Method 301) Sea Level ............................................................................................................................................................... 1,000 VAC minimum 70,000 Feet ............................................................................................................................................................... 500 VAC minimum Insulation Resistance (500 V) .................................................................................................................................... 1,000 ohms minimum Power Rating @ 70 C (Voltage Limited by Power Dissipation or 350 VAC, Whichever is Less) Linear ....................................................................................................................................................................................... .75 watt Audio ........................................................................................................................................................................................ .25 watt Theoretical Resolution ..................................................................................................................................................... Essentially infinite Environmental Characteristics Operating Temperature Range ................................................................................................................................................+1 C to +125 C Storage Temperature Range.................................................................................................................................................. -40 C to +125 C Temperature Coefficient Over Storage Temperature Range ...................................................................................................... 1000 ppm/C Vibration .......................................................................................................................................................................................................20 G Total Resistance Shift ...........................................................................................................................................................1 % maximum Voltage Ratio Shift ..............................................................................................................................................................20 % maximum Shock ...........................................................................................................................................................................................................50 G Total Resistance Shift ...........................................................................................................................................................1 % maximum Voltage Ratio Shift ..............................................................................................................................................................20 % maximum Load Life ....................................................................................................................................1,000 Hours @ Rated Power, 20 % RH, 70 C Total Resistance Shift .........................................................................................................................................................10 % maximum Rotational Life (No Load) .............................................................................................................................................................. 50,000 cycles Total Resistance Shift (Linear taper) ............................................................................................ 10 ohms or 12 %, whichever is greater Total Resistance Shift (Audio taper) ...................................................................................................................................20 % maximum Contact Resistance Variation ....................................................................................................................................................5 % maximum Moisture Resistance .......................................................................................................................... MIL-STD-202, Method 103, Condition B Total Resistance Shift .........................................................................................................................................................20 % maximum IP Rating...................................................................................................................................................................................................... IP 40 Mechanical Characteristics Stop Strength (1/4 " and 6 mm Shaft Diameters) ............................................................................................................ 79.09 N-cm (7 lb.-in.) Mechanical Angle............................................................................................................................................................................... 300 5 Torque Starting (Detented) ..................................................................................................................................... 0.5-1.5 N-cm (0.75-2.25 oz.-in.) Starting (Undetented) ............................................................................................................................... 1.5 N-cm (2.25 oz.-in.) maximum Running (Undetented) ...................................................................................................................... 0.18 to 1.06 N-cm (0.25 to 1.5 oz.-in.) Mounting .................................................................................................................................................... 79.09 N-cm (7 lb.-in.) maximum Weight (Single Section) ............................................................................................................................................ 21 gm (0.75 oz.) maximum Terminals ............................................................................................................................................................................. PC pin or solder lug Soldering Condition Manual Soldering .......................................................................................... 96.5Sn/3.0Ag/0.5Cu solid wire or no-clean rosin cored wire 370 C (700 F) max. for 3 seconds Wave Soldering ................................................................................................................... 96.5Sn/3.0Ag/0.5Cu solder with no-clean flux 260 C (500 F) max. for 5 seconds Wash processes ..............................................................................................................................................................Not recommended Marking .......................................................................................... Manufacturer's trademark, resistance value, part number, and date code Ganging ..................................................................................................................................................................................... 1 cup maximum Hardware .................. One lockwasher and one mounting nut is shipped with each potentiometer, except where noted in the part number. Detents ..........................................................................................................................................................................Center, 10, 20, 30, none For additional features or specifications not shown, consult factory. FOR ORDERING INFORMATION SEE PAGE 4. *RoHS Directive 2002/95/EC Jan. 27, 2003 including annex and RoHS Recast 2011/65/EU June 8, 2011. Specifications are subject to change without notice. The device characteristics and parameters in this data sheet can and do vary in different applications and actual device performance may vary over time. Users should verify actual device performance in their specific applications. PC - "Slimline" 22 mm Square Single Turn Panel Control Product Dimensions Axial PC Pins 14.7 0.5 DIA. (.578 .020) 22.2 0.25 (.874 .010) "F" 7.42 (.292) "L" 11.1 (.437) PANEL HOLE DIMENSIONS 9.53 (.375) 1 2 3 9.0 DIA. (.354) M9 X 0.75-6g SPL 6.25 (.246) .320 (8.13) 1.52 (.060) "F" = 11.1 (.437) 6.35 9.53 OR (.250) (.375) "E" = 3.18 DIA. (.125) 0.79 3 PLCS. (.031) 9.14 DIA. (.360) "E" 2 PLCS. 2.54 5.08 OR (.100) (.200) "L" = SEE SHAFT LENGTH TABLE Radial PC Pins 22.2 0.25 (.874 .010) "L" "F" 14.7 0.5 (.578 .020) DIA. .320 (8.13) 11.1 (.437) PANEL HOLE DIMENSIONS 9.53 (.375) 1 2 3 8.36 (.329) 3.18 DIA. (.125) 11.1 (.437) .28 (.011) 3 PLCS. 6.25 (.246) 0.79 (.031) 3 PLCS. "E" 2 PLCS. "F" = 9.14 DIA. (.360) 6.35 9.53 OR (.250) (.375) "E" = 2.54 5.08 OR (.100) (.200) "L" = SEE SHAFT LENGTH TABLE TOLERANCES EXCEPT WHERE NOTED: 2 .25 (.010) .13 .XXX = (.005) .XX = 1 3 DIMENSIONS: MM (INCHES) Specifications are subject to change without notice. The device characteristics and parameters in this data sheet can and do vary in different applications and actual device performance may vary over time. Users should verify actual device performance in their specific applications. PC - "Slimline" 22 mm Square Single Turn Panel Control Product Dimensions SOLDER LUGS "L" (Dimensions not given are the same as Axial PC pins. "F" 22.2 0.25 (.874 .010) 8.36 (.329) .28 3 PLCS. (.011) Axial PC PINS With Rear Mounting Bracket 7.75 (.305) 6.25 (.246) 6.83 (.269) 1.02 X 2.29 3 PLCS. (.040 X .090) 5.08 (.200) 2 PLCS. 2.03 3 PLCS. (.080) "F" = 6.35 9.53 OR (.250) (.375) 23.37 (.92) "L" 8.31 (.327) 11.43 (.450) 2 PLCS. "E" 2 PLCS. 15.2 18.87 (.600) (.743) 0.76 (.030) 4 PLCS. 17.07 (.672) 1.19 DIA. 7 PLCS. (.047) 5.87 (.231) Radial PC PINS With Side Mounting Bracket "E" = 1.19 DIA. 7 PLCS. (.047) 5.48 (.216) 23.37 (.92) "L" 5.08 2.54 OR (.200) (.100) 7.62 (.300) 2 PLCS. 5.08 (.200) 17.07 (.672) 12.62 (.497) 6.83 (.269) "E" = 0.76 4 PLCS. (.030) "E" 2 PLCS. 11.43 2 PLCS. (.450) 5.08 2.54 OR (.200) (.100) 0.79 (.031) 3 PLCS. "E" 2 PLCS. SHAFT STYLES AND ORIENTATION (Full CCW Rotation) Shaft Style C Shaft Style J 5.54 .076 (.218 .003) "D" Shaft Style R 3.94 + .051/ - .025 (.155 + .002/ - .001) 6.32 + 0.03/ - 0.08 (.249 + .001/ - .003) DIA. 4.75 .051 DIA. (.187 .002) "D" Shaft Style B "D" dimensions extend from shaft end to bushing face 1.19 (.047) 1.6 (.063) Shaft Orientations Shaft Styles B, R 60 2 120 2 DIMENSIONS: 1.6 (.063) "D" = (shaft length, FMS) - (bushing length) Shaft Styles C, J Shaft Style Y 6.32 + 0.03/ - 0.08 (.249 + .001/ - .003) DIA. 6.00 0.05 DIA. (.236 .002) 1.57 (.062) DIA. 4.7 0.05 (.185 .002) 1.19 (.047) Slot depth (Y shaft) 9.65 (.380) for shafts <1 " (2.54) length; 14.7 (.520) for shafts 1 " (2.54) length Shaft Style Y 60 2 MM (INCHES) TOLERANCES EXCEPT WHERE NOTED: .25 (.010) .13 .XXX = (.005) .XX = Specifications are subject to change without notice. The device characteristics and parameters in this data sheet can and do vary in different applications and actual device performance may vary over time. Users should verify actual device performance in their specific applications. How to Order PC "Slimline" Panel Controls P C W 1 J - B 2 4 - B A B 1 0 3 L RoHS IDENTIFIER Code Description L Compliant SHAFT LENGTH (FMS) Code 16 20 24 28 32 36 19 22 24 Description 1/2 " (12.7 mm) Length 5/8 " (15.9 mm) Length 3/4 " (19 mm) Length 7/8 " (22.2 mm) Length 1 " (25.4 mm) Length 1-1/8 " (28.6 mm) Length Metric 19 mm Length 22 mm Length 24 mm Length SHAFT STYLES (See Outline Drawing) Code Description B 1/4 " (6.35 mm) Dia. Slotted C 1/4 " (6.35 mm) Dia. Flatted J 3/16 " (4.76 mm) Dia. Flatted R 6 mm Dia. Slotted (Use Metric Lengths Only) Y 3/16 " (4.76 mm) Dia. Split Shaft Available Shaft Styles B J B, C, J, Y B, C, J, Y B, C, J, Y B, C, J, Y R R R Code 501 102 252 502 RESISTANCE VALUES TR Code TR Code 500 103 10 K 104 1 K 203 20 K 254 2.5 K 253 25 K 504 5 K 503 50 K 105 TR 100 K 250 K 500 K 1 M ELEMENT TAPER VERSIONS Code Taper Description B Lin. CP 20 % D CW Audio CP 20 % G CCW Audio CP 20 % DETENT CONFIGURATIONS Code Taper Description A No Detents B 10 Detents C Center Detent Only D 20 Detents E 30 Detents F CCW Detent Only HOUSING TERMINAL CONFIGURATION ANTI-ROTATION LUG Code Description J 9:00 Position D None 1 Features Rear Mounting Bracket Side Mounting Bracket Axial Terminals .100 " (2.54 mm) Centers Radial Terminals .100 " (2.54 mm) Centers Radial Terminals .200 " (5.08 mm) Centers Solder Lugs .200" (5.08 mm) Centers Axial Terminals .200 " (5.08 mm) Centers Hardware Included NO. SECTIONS Single Code A B C D E F G H J K L M N X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X BUSHING CONFIGURATION Code Description W 9 mm x .250 " (6.35 mm) Length Threaded M9 x 0.75 6g 5 Pl L 9 mm x .375 " (9.53 mm) Length Threaded M9 x 0.75 6g 5 Pl Available Shaft Styles All B, C, R Panel mount hardware not included as standard on bracketed versions. The sample part number demonstrates the identification code for Bourns Slimline Potentiometers. The part number shown is a commonly used model, typically available from stock. Boldface features are Bourns standard options. All others are available with higher minimum order quantities. REV. 08/14 Specifications are subject to change without notice. The device characteristics and parameters in this data sheet can and do vary in different applications and actual device performance may vary over time. Users should verify actual device performance in their specific applications. Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Bourns: PCW1D-C24-BAB503 PCW1D-R19-BAB103 PCW1J-J20-DAD104 PCW1J-B24-AEB103 PCW1D-C24-BAB501 PCW1D-C24-BAB502 PCW1J-B24-AEB501 PCW1J-B24-AEB503 PCW1J-B24-CCB103 PCW1J-B24-CCB104 PCW1J-B24-CCB102 PCW1J-B28-CCB103 PCW1J-B36-BAB254 PCW1J-B24-BAB203 PCW1D-B24-CEB105 PCW1J-J20-BAB103 PCL1D-B24-KDB102 PCW1J-C24-AAD502 PCW1D-B16-MAB753 PCW1D-B24-FAB103 PCW1J-B24-BAB104 PCW1J-B24-BAB105 PCW1J-B24-BAB103 PCW1D-B24-BCD103 PCW1J-B36-BAB503 PCW1J-B28-BAB102 PCW1J-B24-BAB102 PCW1J-B28-BAB104 PCL1D-B24-CAB103 PCW1J-B28-BAB103 PCW1J-B16-BAD103 PCW1J-J20-EAB103 PCW1D-B16-KAB502 PCW1D-C24-GAB103 PCW1J-C24-KAB103 PCW1D-C24-KAB254 PCW1J-C28-KAB103 PCW1J-C28-KAB102 PCW1D-B24-BAD502 PCW1J-C24-KAB104 PCW1J-B24-KAB502 PCW1J-B28-KAB502 PCW1J-B28-JCB103 PCW1J-R24-CAB503 PCW1D-J20-FAB104 PCW1J-C24-BAB504 PCW1J-C24-BAB503 PCW1J-C28-BAB503 PCW1J-C28-BAB502 PCW1J-C36-BAB103 PCW1J-C32-BAB103 PCW1J-B24-CAD254 PCW1J-B24-CAD203 PCW1J-B28-BAB503 PCW1J-B24-BAB502 PCW1J-B28-BAB502 PCL1J-B28-BAB504 PCW1J-R24-BBB502 PCW1J-B32-BAB103 PCW1J-B24-BAB504 PCL1JB24-BAB503 PCW1J-B24-BAB503 PCW1J-R24-LAB103 PCW1D-B32-BCB102 PCW1D-B24-BCB502 PCW1J-B24BCD103 PCW1D-C24-BEB105 PCW1J-R24-CAB102 PCW1J-R24-CAB104 PCW1J-R24-CAB103 PCW1D-B24CAB502 PCW1D-B24-BAB103 PCW1D-B28-BAB103 PCW1D-B24-BAB104 PCW1D-B24-BAB102 PCW1D-B32BAB502 PCW1D-B24-EAD103 PCW1D-C24-BAB254 PCW1J-C28-BAB102 PCW1J-C28-BAB103 PCW1J-C28BAB104 PCW1J-R24-BCB103 PCW1J-C24-DAB102 PCW1D-R24-BAB252 PCW1D-B24-EAB501 PCL1D-R24KAB252 PCW1D-R24-KAB252 PCW1J-B24-KBB103 PCW1J-B24-CAB104 PCW1J-B36-CAB502 PCW1J-B24CAB102 PCW1J-B24-CAB103 PCW1D-R19-EAB502 PCW1J-C24-CAB252 PCW1J-C28-CAB254 PCW1J-B28CEB105 PCW1J-C24-BCB502 PCW1J-B24-CEB104 PCW1J-C24-CAB503 PCL1J-C28-CAB502