OPERATING ALTITUDE Note.8 5000 meters
SPECIFICATIONSPECIFICATION
MODEL
DC VOLTAGE
RATED CURRENT
CURRENT RANGE Note.2
RATED POWER
OUTPUT
LINE REGULATION
LOAD REGULATION
SETUP, RISE TIME
HOLD UP TIME (Typ.)
VOLTAGE RANGE Note.6
FREQUENCY RANGE
EFFICIENCY (Typ.)
INPUT
INRUSH CURRENT (Typ.)
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
WORKING HUMIDITY
WORKING TEMP.
OVER TEMPERATURE
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
MTBF
DIMENSIONOTHERS
NOTE
PACKING
OVERLOAD
OVER VOLTAGE
AC CURRENT (Typ.)
20 ~ 90% RH non-condensing
-40 ~ +85 (Refer to "Derating Curve")℃
-40 ~ +85 , 10 ~ 95% RH non-condensing℃
±℃ ℃0.03%/ (0 ~ 60 )
10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes
1210Khrs min. MIL-HDBK-217F (25 )℃
SAFETY STANDARDS
RIPPLE & NOISE (max.) Note.4
VOLTAGE TOLERANCE Note.5
ENVIRONMENT
SAFETY &
EMC
(Note.9)
PROTECTION
Protection type : Shut off o/p voltage, clamping by zener diode
Protection type : Shut down o/p voltage, recovers automatically after temperature goes down
I/P-O/P:4KVAC
I/P-O/P:100M Ohms / 500VDC / 25 / 70% RH℃
LEAKAGE CURRENT (max.) Note.7
ISOLATION LEVEL Primary-Secondary: 2xMOPP
Parameter
Parameter
ESD
Standard
Standard
EN55011 (CISPR11)
EN55011 (CISPR11)
EN61000-3-2
EN61000-3-3
EN61000-4-2
EN61000-4-3
EN61000-4-4
EN61000-4-5
EN61000-4-6
EN61000-4-8
EN61000-4-11
Test Level / Note
Test Level / Note
Class B
Class B
Class A
-----
EMC IMMUNITY
EMC EMISSION
100% dip 1 periods, 30% dip 25 periods,
100% interruptions 250 periods
SOLDERING TEMPERATURE 260 5 /10sec.max.℃± ℃
1500ms, 30ms/230VAC 1500ms, 30ms/115VAC at full load
40ms/230VAC 10ms/115VAC at full load
80 ~ 264VAC
47 ~ 440Hz
0.6A/115VAC 0.3A/230VAC
COLD START 20A/115VAC 45A/230VAC
110% ~ 150% rated output power
Protection type : Hiccup mode, recovers automatically after fault condition is removed
MPM-15-3.3
Touch current <80 A/264VAC
μ
MPM-15-5 MPM-15-12 MPM-15-15 MPM-15-24
±0.3%
±0.5%
±0.3%
±0.5%
±0.3%
±0.5%
±0.5%
±0.5%
±0.5%
±2.0%
5V3.3V 12V 15V 24V
3A3.5A 1.25A 1A 0.63A
0 ~ 3A0 ~ 3.5A 0 ~ 1.25A 0 ~ 1A 0 ~ 0.63A
15W11.6W 15W 15W 15.1W
13.8 ~ 16.2V 17.3 ~ 20.3V 27.6 ~ 32.4V
5.8~ 6.8V3.8 ~ 5V
3.85A 3.3A 1.38A 1.1A 0.69A
MPM-15 series
±2.0% ±2.0% ±2.0% ±2.0%
±0.5%
0.056Kg; 240pcs/14.4Kg/0.97CUFT
PEAK CURRENT
15W High Reliable Green Medical Encapsulated Type
PEAK LOAD(10sec.)
Note.3
12.7W 16.5W 16.6W 16.5W 16.6W
IEC60601-1, EN60601-1, , ULANSI/AAMI ES60601-1(3.1 version), CAN/CSA-C22 3 Edition approved; Design
rd
EAC TP TC 004
refer to EN60335-1
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.℃
2. No minimum load required.
3. 33% Duty cycle maximum within every 30 seconds. Average output power should not exceed the rated power.
4. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1 f & 47 f parallel capacitor.μμ
5. Tolerance : includes set up tolerance, line regulation and load regulation.
6. Derating may be needed under low input voltages. Please check the derating curve for more details.
7. Touch current was measured from primary input to DC output.
8. The ambient temperature derating of 3.5 /1000m with fanless models and of 5 /1000m with fan models for operating altitude higher than 2000m(6500ft).℃℃
9. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still
meets EMC directives. For guidance on how to perform these EMC tests, please refer to EMI testing of component power supplies.
(as available on http://www.meanwell.com)
Level 4, 15KV air ; Level 4, 8KV contact
Level 3, 1KV/Line-Line
52.4*27.2*24mm (L*W*H) 2.06 *1.07 *0.94 inch
or ″″″
EN60601-1-2
EFT bursts
Surge susceptibility
Conducted susceptibility
Magnetic field immunity
Conducted emission
Radiated emission
Harmonic current
Voltage flicker
Level 3, 10V/m( 80MHz~2.7GHz )
Level 4, 30A/m
Level 3, 10V
Level 3, 2KV
Voltage dip, interruption
150mVp-p150mVp-p 150mVp-p 180mVp-p 180mVp-p
85.5%83.5% 86.5% 87% 86.5%
Table 9, 9~28V/m( 385MHz~5.78GHz )
RF field susceptibility
File Name:MPM-15-SPEC 2019-12-13
LEAD TEMPERATURE 260 5 ,5s (max.)±℃