ACDC
Specification
150500 Watts
•Single Output Industrial Supplies
•High Efficiency
•Low Cost
•150 W Convection Cooled
•300 W & 500 W with Internal Fans
•Outputs from 12 V to 48 V
•3 Year Warranty
LCL Series
Input
Input Voltage • 85-264 VAC (127-370 VDC) (see note 1)
Input Frequency • 47-63 Hz
Input Current • 2.1 A max for LCL150, 4.5 A max for
LCL300, 6.6 A max for LCL500
Inrush Current • 40 A max for LCL150,
60 A max for LCL300 & 500
cold start at 25 °C, 230 VAC
Power Factor • >0.9
Earth Leakage Current • <2 mA at 264 VAC, 60 Hz
Input Protection • LCL150: T3.15 A/250 V,
LCL300: T6.3A/250 V,
LCL500: T10A/250 V,
internal fuse fitted in line
Output
Output Voltage • See tables
Output Voltage Trim • See tables
Initial Set Accuracy • ±100 mV at 50% load
Minimum Load • None required
Start Up Delay • 2 s max for LCL150, 1.5 s max for LCL300,
0.8 s max for LCL500
Start Up Rise Time • 50 ms max for LCL150,
35 ms max for LCL300 & LCL500
Hold Up Time • 10 ms min at 115 VAC and full load
Line Regulation • ±0.5% max for LCL150,
±0.3% for LCL300 & LCL500
Load Regulation • ±1% max
Transient Response • 4% max deviation recovery to within 1%
in 500 µs for a 50% load change
Ripple & Noise • See tables
Overvoltage Protection • 110-140%, recycle input to reset
Overtemperature • Output turns off when OTP triggered,
Protection measured internally, auto recovery
Overload Protection • 110-150% of rated output power. Delayed
by 1 s min to allow for peak loads.
Short Circuit Protection • Trip and restart (hiccup mode),
auto recovery
Remote Sense • Fitted to LCL500 only, compensates for
0.25 V max each line
Remote On/Off • Fitted on LCL500 only,
On = logic low or open circuit,
Off = logic high
xppower.com
General
Efficiency • 88% typical at full load & 230 VAC
Isolation • 3000 VAC Input to Output
1500 VAC Input to Ground
500 VAC Output to Ground
Switching Frequency • 90-110 kHz main converter & 45-190 kHz
PFC for LCL150, 80-190 kHz main converter
& 62-65 kHz PFC for LCL300 & 500
Power Density • 2.7 W/in3LCL150, 4.4 W/in3LCL300,
4.9 W/in3LCL500
MTBF • LCL150: >489 kHrs,
LCL300: >235 kHrs,
LCL500: >211 kHrs to MIL-HBK-217F at
25 °C, GB
Environmental
Operating Temperature • -10 °C to +70 °C, derate from 100% load
at 50 °C to 50% load at 70 °C
Cooling • LCL150 convection cooled, LCL300 &
LCL500 have internal fans
Operating Humidity • 5% to 90% non condensing
Storage Temperature • -40 °C to +85 °C
Operating Altitude • 3000 m
Vibration • 10-500 Hz, 2 g, 10 mins per cycle on
3 axes
EMC & Safety
Emissions • EN55022 level B conducted,
level A radiated
Harmonic Currents • EN61000-3-2 class A
LCL150: EN61000-3-2 class C for loads ≥40%
LCL300 & LCL500: EN61000-3-2 class C
for loads ≥20%
Voltage Flicker • EN61000-3-3
ESD Immunity • EN61000-4-2, ±4 kV contact,
±8 kV air discharge, Performance Criteria A
Radiated Immunity • EN61000-4-3, level 2 Perf Criteria A
EFT/Burst • EN61000-4-4, level 2 Perf Criteria A
Surge • EN61000-4-5,
installation class 3, Perf Criteria A
Conducted Immunity • EN61000-4-6, level 2 Perf Criteria A
Magnetic Field • EN61000-4-8, 1 A/m Perf Criteria A
Dips & Interruptions • EN61000-4-11, 30% 10 ms, 60% 100 ms,
100% 5000 ms, Perf Criteria A, B, B
Safety Approvals • EN60950-1, UL60950-1, CSA60950
No 22.2
ACDC
LCL150
Model and Ratings
Mechanical Details
1. Output power derates linearly from 100% at 90 VAC to 90% at 85 VAC.
2. Measured with 20 MHz bandwidth.
Output Power(1) Output Voltage Trim Range Output Current Ripple & Noise(2) Model Number
150 W
12.0 V 11.0-13.0 V 12.5 A 100 mV pk-pk LCL150PS12
13.5 V 12.5-14.5 V 11.1 A 100 mV pk-pk LCL150PS13
15.0 V 14.0-16.0 V 10.0 A 100 mV pk-pk LCL150PS15
24.0 V 23.0-25.0 V 6.3 A 150 mV pk-pk LCL150PS24
27.0 V 26.0-28.0 V 5.6 A 150 mV pk-pk LCL150PS27
48.0 V 47.0-49.0 V 3.1 A 250 mV pk-pk LCL150PS48
Output Power (%)
Ambient Temperature (°C)
80
60
40
20
010-10 20 30 40 50 60 70
100
Output Power (%)
Input Voltage (VAC)
90
90 100 110 120 230 240 25085 264
100
Notes
1.02
(26.0)
4 x M4 x 0.7 THD
0.15 (3.8) Max Screw Penetration
1.97
(50.0) 0.90
(23.0)
0.57
(14.5)
4.64 (118.0)
0.57
(14.5)
0.90
(23.0)
4.64
(118.0)
1.02
(26.0)
7.55 (192.0)
T
erminal Block, M4 Screw 7 pins 0.37 (9.5) centre
3.74
(95.0)
J1
2.44 (62.0) 2.83 (72.0)
7
1
4 x M4 x 0.7 THD
0.15 (3.8) Max Screw Penetration
2 x M4 x 0.7 THD
0.15 (3.8) Max Screw Penetration
Pin Function
1 +Vout
2 +Vout
3 -Vout
4 -Vout
5 Ground
6 Neutral
7 Line
Notes
1. All dimensions shown in inches (mm).
2. Weight: 1.39 lbs (630 g) approx.
3. Tolerance is ±0.05 (±0.2) maximum.
ACDC
LCL300
Model and Ratings
Mechanical Details
Derating Curves
1. Output power derates linearly from 100% at 90 VAC to 90% at 85 VAC.
2. Measured with 20 MHz bandwidth.
Output Power(1) Output Voltage Trim Range Output Current Ripple & Noise(2) Model Number
300 W
12.0 V 11.0-13.0 V 25.0 A 150 mV pk-pk LCL300PS12
13.5 V 12.5-14.5 V 22.0 A 150 mV pk-pk LCL300PS13
15.0 V 14.0-16.0 V 20.0 A 150 mV pk-pk LCL300PS15
310 W 24.0 V 23.0-25.0 V 13.0 A 150 mV pk-pk LCL300PS24
315 W 27.0 V 26.0-28.0 V 11.7 A 200 mV pk-pk LCL300PS27
320 W 48.0 V 47.0-49.0 V 6.70 A 240 mV pk-pk LCL300PS48
Output Power (%)
Ambient Temperature (°C)
80
60
40
20
100
010-10 20 30 40 50 60 70
Output Power (%)
Input Voltage (VAC)
90
90 100 110 120 230 240 25085 264
100
Notes
1. All dimensions shown in inches (mm
2. Weight: 1.94 lbs (880 g) approx.
3. Tolerance is ±0.05 (±0.2) maximum.
4. Airflow direction is out of the unit at fan.
Notes
1.97
(50.0)
0.63
(16.0)
8.07 (205.0)
1.97
(50.0)0.94
(24.0)
0.63 (16.0)
6.81 (173.0)
6.81 (173.0)
1.97
(50.0)
0.98
(25.0)
0.50
(12.5)
4.33
(110.0)
7.44 (189.0)
J1
9
1
Terminal Block, M4 Screw 9 pins 0.37 (9.5) centre
3 x M4 x 0.7 THD
0.15 (3.8) Max Screw Penetration
4 x M4 x 0.7 THD
0.15 (3.8) Max Screw Penetration
3 x M4 x 0.7 THD
0.15 (3.8) Max Screw Penetration
J1 Pin Connections
Pin Function
1 +Vout
2 +Vout
3 +Vout
4 -Vout
5 -Vout
6 -Vout
7 Ground
8 Neutral
9 Line
03-July-14
ACDC
LCL500
Model and Ratings
Derating Curves
Output Power (%)
Input Voltage (VAC)
90
90 100 110 120 230 240 25085 264
100
Mechanical Details
1. Output power derates linearly from 100% at 90 VAC to 90% at 85 VAC.
2. Measured with 20 MHz bandwidth.
Output Power(1) Output Voltage Trim Range Output Current Ripple & Noise(2) Model Number
500 W
12.0 V 11.0-13.0 V 42.0 A 120 mV pk-pk LCL500PS12
13.5 V 12.5-14.5 V 37.0 A 150 mV pk-pk LCL500PS13
15.0 V 14.0-16.0 V 34.0 A 150 mV pk-pk LCL500PS15
24.0 V 23.0-25.0 V 21.0 A 150 mV pk-pk LCL500PS24
27.0 V 26.0-28.0 V 18.5 A 150 mV pk-pk LCL500PS27
48.0 V 47.0-49.0 V 10.5 A 240 mV pk-pk LCL500PS48†
Output Power (%)
Ambient Temperature (°C)
80
60
40
20
100
010-10 20 30 40 50 60 70
Notes
1.Dimensions shown in inches (mm).
2. Weight: 3.2 lbs (1.45 kg) approx.
3. Tolerance is ±0.05 (±0.2) maximum.
Applying >4.5 V to Pin 2 with
respect to Pin 1 turns output off.
Applying <0.8 V to Pin 2 with
respect to Pin 1 or open circuit
turns output on.
Mating Connectors (J2):
WST P4-I25002 housing
WST I25002BS contacts
Notes
1.41
(36.0)
2.08
(53.0)
0.60
(15.0)
1.00
(25.5)
5.00
(127.0)
9.21 (234.0)
9.84 (250.0)
7.75 (197.0) 0.60
(15.0)
1.00
(25.5)
1.41
(0.36)
7.75 (197.0) 1.41
(36.0)
3.54
(90.0)
J1
J2
9
1
1
4
Terminal Block, M4 Screw 9 pins 0.37 (9.5) centre
AIRFLOW
4 x M4 x 0.7 THD
0.15 (3.8) Max Screw Penetration
4x M4 x 0.7 THD
0.15 (3.8) Max Screw Penetration
4 x M4 x 0.7 THD
0.15 (3.8) Max Screw Penetration
J1 Pin Connections
Pin Function
1 +Vout
2 +Vout
3 +Vout
4 -Vout
5 -Vout
6 -Vout
7 Ground
8 Neutral
9 Line
J2 Pin Connections
Pin Function
1 Remote On/Off -
2 Remote On/Off +
3 Sense -
4 Sense +