MCC omponents 20736 Marilla Street Chatsworth !"# $ % !"# TM Micro Commercial Components MBR30150CT Features * * * * * * * * Low Power Loss, High Efficiency 30Amp Schottky Barrier Rectifier 150Volts Guardring for overvoltage protection Low forward voltage drop and High frequency operation For use in high frequency inverters,free wheeling and polarity protection applications Lead Free Finish/RoHS Compliant(Note 1) ("P" Suffix designates RoHS Compliant. See ordering information) Halogen free available upon request by adding suffix "-HF" TO-220AB Epoxy meets UL 94 V-0 flammability rating Moisture Sensitivity Level 1 C B Maximum Ratings and Electrical Characteristics * Mounting Torgue: 5 in-lbs Maximum S F Q ( TC = 25oC unless otherwise noted ) T Parameter Symbol MBR30150CT Unit VRRM 150 Volts Working peak reverse voltage VRWM 150 Volts Maximum DC blocking voltage VDC 150 Volts IF(AV) 30 15 Amps Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) per leg IFSM 200 Amp s Peak repetitive reverse current per leg at tp = 2.0us, 1KHz IRRM 1.0 Amp dv/dt 10,000 V/us Maximum repetitive peak reverse voltage Maximum average forward rectified current (See Fig. 1) Total device Voltage rate of change (rated VR) A U 1 2 H K at IF=30A, TC=125oC 0.86 o TJ=25 C Operating junction and storage temperature range Volt 0.1 mA 1.0 mA RJC 1.7 VISOL 4500 (Note 2) 3500 (Note 3) 1500 (Note 4) TJ, TSTG o C/W Volts o -55 to +150 C 1. High Temperature Solder Exemption Applied, see EU Directive Annex 7. 2. Clip mounting (on case), where lead does not overlap heatsink with 0.110" offset 3. Clip mounting (on case), where leads do overlap heatsink 4. Screw mounting with 4-40 screw, where washer diameter is < 4.9 mm (0.19") 5.Pulse test: 300us pulse width, 1% duty cycle Revision: B PIN 1 PIN 2 CASE PIN 3 IR RMS Isolation voltage (MBRF type only) from terminals to heatsink with t = 1.0 second, RH < 30% Notes: 0.75 0.99 Typical thermal resistance per leg R N 0.90 VF at IF=30A, TC=25oC TJ=125oC J D G at IF=15A, TC=25oC Maximum reverse current per leg at working peak reverse voltage V L Maximum instantaneous forward voltage per leg (Note 5) at IF=15A, TC=125oC 3 DIM A B C DIMENSIONS INCHES MM MIN MAX MIN MAX .560 .625 14.22 15.88 .380 .420 9.65 10.67 .140 .190 3.56 4.82 D F G H J K L N .020 .139 .190 --.012 .500 .045 .190 .045 .161 .110 .250 .025 .580 .060 .210 0.51 3.53 2.29 --0.30 12.70 1.14 4.83 1.14 4.09 2.79 6.35 0.64 14.73 1.52 5.33 Q R S T U V .100 .080 .045 .230 ----.045 .135 .115 .055 .270 .050 ----- 2.54 2.04 1.14 5.84 ----1.15 3.43 2.92 1.39 6.86 1.27 ----- www.mccsemi.com 1 of 3 NOTE 2013/01/01 MCC MBR30150CT Micro Commercial Components RATINGS AND CHARACTERISTICS CURVES (TA = 25 C unless otherwise noted) 280 Peak Forward Surge Current (A) Average Forward Current (A) 40 35 30 25 20 15 10 5 TJ = TJ max. 8.3 ms Single Half Sine-Wave 240 200 160 120 80 40 0 0 25 0 50 75 100 125 150 1 Case Temperature (C) 10000 Junction Capacitance (pF) 100 Instantaneous Forward Current (A) 100 Figure 2. Maximum Non-Repetitive Peak Forward Surge Current Per Diode Figure 1. Forward Derating Curve 10 TJ = 125 C TJ = 75 C 1 TJ = 25 C 0.1 0.1 1000 100 10 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 0.1 1.1 1.2 Instantaneous Forward Voltage (V) 1 10 100 Reverse Voltage (V) Figure 3. Typical Instantaneous Forward Characteristics Per Diode Figure 5. Typical Junction Capacitance Per Diode 100 Transient Thermal Impedance (C/W) 10000 Instantaneous Reverse Current (A) 10 Number of Cycles at 60 Hz 1000 TJ = 125 C C 100 10 TJ = 75 C 1 0.1 TJ = 25 C 0.01 10 20 30 40 50 60 70 80 1 0.1 0.01 90 0.1 1 10 100 t - Pulse Duration (s) Percent of Rated Peak Reverse Voltage (%) Figure 4. Typical Reverse Characteristics Per Diode Revision: B 10 Figure 6. Typical Transient Thermal Impedance Per Diode www.mccsemi.com 2 of 3 2013/01/01 TM MCC TM Micro Commercial Components Ordering Information Device Packing (Part Number)-BP Bulk;1Kpcs/Box Note : Adding "-HF" suffix for halogen free, eg. Part Number-BP-HF ***IMPORTANT NOTICE*** Micro Commercial Components Corp. reserves the right to make changes without further notice to any product herein to make corrections, modifications , enhancements , improvements , or other changes . Micro Commercial Components Corp . does not assume any liability arising out of the application or use of any product described herein; neither does it convey any license under its patent rights ,nor the rights of others . The user of products in such applications shall assume all risks of such use and will agree to hold Micro Commercial Components Corp . and all the companies whose products are represented on our website, harmless against all damages. ***LIFE SUPPORT*** MCC's products are not authorized for use as critical components in life support devices or systems without the express written approval of Micro Commercial Components Corporation. ***CUSTOMER AWARENESS*** Counterfeiting of semiconductor parts is a growing problem in the industry. Micro Commercial Components (MCC) is taking strong measures to protect ourselves and our customers from the proliferation of counterfeit parts. MCC strongly encourages customers to purchase MCC parts either directly from MCC or from Authorized MCC Distributors who are listed by country on our web page cited below. Products customers buy either from MCC directly or from Authorized MCC Distributors are genuine parts, have full traceability, meet MCC's quality standards for handling and storage. MCC will not provide any warranty coverage or other assistance for parts bought from Unauthorized Sources. MCC is committed to combat this global problem and encourage our customers to do their part in stopping this practice by buying direct or from authorized distributors. Revision: B www.mccsemi.com 3 of 3 2013/01/01