LM2757 LM2757 Switched Capacitor Boost Regulator with High Impedance Output in Shutdown Literature Number: SNVS536D LM2757 Switched Capacitor Boost Regulator with High Impedance Output in Shutdown General Description Features The LM2757 is a constant frequency pre-regulated switchedcapacitor charge pump that operates at 1.25 MHz to produce a low-noise regulated output voltage. The device can be configured to provide up to 100 mA at 4.1V, 110 mA at 4.5V, or 180 mA at 5V. Excellent efficiency is achieved without the use of an inductor by operating the charge pump in a gain of either 3/2 or 2 according to the input voltage and output voltage option selection. The LM2757 presents a high impedance at the VOUT pin when shut down. This allows for use in applications that require the regulated output bus to be driven by another supply while the LM2757 is shut down. A perfect fit for space-constrained, battery-operated applications, the LM2757 requires only 4 small, inexpensive ceramic capacitors. LM2757 is a tiny 1.2 mm X 1.6 mm 12-bump micro SMD device. Built in soft-start, over-current protection, and thermal shutdown features are also included in this device. Dual gain converter (2x, 3/2x) with up to 93% Efficiency. Inductorless solution uses only 4 small ceramic capacitors. Total solution area < 12mm2. True input-output and output-input disconnect. Up to 180 mA output current capability (5V). Selectable 4.1V, 4.5V or 5.0V output. Pre-regulation minimizes input current ripple. 1.24 MHz switching frequency for a low-noise, low-ripple output voltage. Integrated Over Current and Thermal Shutdown Protection. Tiny 1.2 mm X 1.6 mm X 0.4 mm pitch, 12-bump micro SMD package. Applications USB/USB-OTG/HDMI Power Supercapacitor Charger Keypad LED Drive Audio amplifier power supply Low-current Camera Flash General Purpose Li-Ion-to-5V Conversion Cellular Phone SIM cards Typical Application Circuit 30033723 30033701 (c) 2009 National Semiconductor Corporation 300337 www.national.com LM2757 Switched Capacitor Boost Regulator with High Impedance Output in Shutdown August 26, 2009 LM2757 Connection Diagram and Package Mark Information 12-Bump Micro SMD Package, 0.4mm Pitch National Semiconductor Package Number TMD12 30033702 Note 1: The actual physical placement of the package marking will vary from part to part. The package marking "X" designates the single digit date code. "V" is a NSC internal code for die traceability. Both will vary considerably. "DL" identifies the device (part number, option, etc.). Pin Descriptions Pin # Name Description A1 C2+ Flying Capacitor C2 Connection A2 VOUT Regulated Output Voltage A3 C1+ Flying Capacitor C1 Connection B1 C1- Flying Capacitor C1 Connection B2 VIN Input Voltage Connection Input Voltage Connection B3 VIN C1 GND Ground Connection C2 GND Ground Connection C3 C2- Flying Capacitor C2 Connection D1 NC No Connect -- Do not connect this pin to any node, voltage or GND. Must be left floating. D2 M1 Mode select pin 1 D3 M0 Mode select pin 0 Mode Selection Definition M0 M1 Output Voltage Mode 0 0 Device Shutdown, Output High Impedance 0 1 5.0V 1 0 4.5V 1 1 4.1V Order Information Order Number LM2757TM LM2757TMX www.national.com Package Mark ID Package XV (A1 Bump Marking) DL 12-Bump SMD 0.4mm pitch 2 Supplied as: 250 Units, Tape & Reel 3000 Units, Tape & Reel Operating Ratings If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. (Notes 2, 3) VIN Pin: Voltage to GND M0, M1 pins: Voltage to GND Continuous Power Dissipation (Note 4) Junction Temperature (TJ-MAX) Storage Temperature Range Maximum Lead Temperature (Soldering, 10 sec.) ESD Rating (Note 5) Human Body Model: LM2757 Absolute Maximum Ratings (Notes 2, 3) Input Voltage Range Junction Temperature (TJ) Range Ambient Temperature (TA) Range (Note 6) -0.3V to 6.0V -0.3V to 6.0V Internally Limited 2.7V to 5.5V -30C to +110C -30C to +85C Thermal Properties 150C -65C to +150 C 265C Electrical Characteristics Junction-to-Ambient Thermal Resistance (JA), micro SMD Package (Note 7) 75C/W 2.5 kV (Notes 3, 8) Limits in standard typeface are for TA = 25C. Limits in boldface type apply over the full operating ambient temperature range (-30C TA +85C) . Unless otherwise noted, specifications apply to the Typical Application Circuit (pg. 1) with: VIN = 3.6V, V (M0) = 0V, V(M1) = VIN,CIN = C2 = 0.47 F, CIN= COUT = 1.0 F (Note 9). Symbol Parameter Condition Min Typ Max 4.870 (-2.6%) 5.0 5.130 (+2.6%) 4.865 (-2.7%) 5.0 5.130 (+2.6%) 3.0V VIN 5.5V IOUT = 0 to 110 mA V(M0) = VIN, V(M1) = 0V 4.406 (-2.1%) 4.5 4.613 (+2.5%) 3.0V VIN 5.5V IOUT = 0 to 100 mA V(M0) = VIN, V(M1) = VIN 3.985 (-2.8%) 4.1 4.223 (+3.0%) V(M0) = 0V, V(M1) = VIN (5.0V) IOUT = 0 mA VIN = 3.6V 2.4 2.79 V(M0) = VIN, V(M1) = 0V (4.5V) IOUT = 0 mA VIN = 3.6V 1.5 1.80 V(M0) = VIN, V(M1) = VIN (4.1V) IOUT = 0 mA VIN = 3.6V 1.3 1.65 V(M0) = 0V, V(M1) = 0V VIN = 3.6V 1.1 2.0 Units 3.2V VIN 5.5V -30C TA +60C IOUT = 0 to 180 mA V(M0) = 0V, V(M1) = VIN 3.0V VIN 5.5V VOUT IQ Output Voltage Quiescent Supply Current ISD Shutdown Supply Current VR Output Voltage Ripple fSW Switching Frequency VIN Logic Input High -30C TA +85C IOUT = 0 to 150 mA V(M0) = 0V, V(M1) = VIN IOUT = 150 mA V(M0) = 0V, V(M1) = VIN (5.0V) 20 V mA A mVp-p 3.0V VIN 5.5V 3.0V VIN 5.5V Input pins: M1, M0 3.0V VIN 5.5V 3 0.932 (-25%) 1.0 1.242 1.552 (+25%) MHz VIN V www.national.com LM2757 Symbol Parameter VIL Logic Input Low RPULLDOWN Condition Input pins: M1, M0 Min 3.0V VIN 5.5V 0 Logic Input Pulldown Resistance (M0, M1) V(M1, M0) = 5.5V 324 IIH Logic Input High Current IIL Logic Input Low Current VG Gain Transition Voltage ISC Short Circuit Output Current ION VOUT Turn-On Time from Shutdown (Note 10) Typ Max Units 0.40 V 457 k Input Pins: M1, M0 V(M1, M0) = 1.8V(Note 11) 5 A Input Pins: M1, M0 V(M1, M0) = 0V 10 nA 1.5X to 2X, V(M0) = VIN, V(M1)=0V 3.333 V 2X to 1.5X, V(M0) = VIN, V(M1)=0V 3.413 V Hysteresis, V(M0) = VIN, V(M1)=0V 80 mV 1.5X to 2X, V(M0) = 0V, V(M1)=VIN 3.87 V 2X to 1.5X, V(M0) = 0V, V(M1)=VIN 3.93 V Hysteresis, V(M0) = 0V, V(M1)=VIN 60 mV VOUT = 0V 250 mA 300 s Note 2: Absolute Maximum Ratings indicate limits beyond which damage to the component may occur. Operating Ratings are conditions under which operation of the device is guaranteed. Operating Ratings do not imply guaranteed performance limits. For guaranteed performance limits and associated test conditions, see the Electrical Characteristics tables. Note 3: All voltages are with respect to the potential at the GND pins. Note 4: Internal thermal shutdown circuitry protects the device from permanent damage. Thermal shutdown engages at TJ=145C (typ.) and disengages at TJ=135C (typ.). Note 5: The Human body model is a 100 pF capacitor discharged through a 1.5 k resistor into each pin. Note 6: In applications where high power dissipation and/or poor package thermal resistance is present, the maximum ambient temperature may have to be derated. Maximum ambient temperature (TA-MAX) is dependent on the maximum operating junction temperature (TJMAX-OP=125C), the maximum power dissipation of the device in the application (PD-MAX), and the junction-to-ambient thermal resistance of the part/package in the application (JA), as given by the following equation: TA-MAX = TJ-MAX-OP - (JA x PD-MAX). Note 7: Junction-to-ambient thermal resistance (JA) is taken from a thermal modeling result, performed under the conditions and guidelines set forth in the JEDEC standard JESD51-7. The test board is a 4-layer FR-4 board measuring 102 mm x 76 mm x 1.6 mm with a 2x1 array of thermal vias. The ground plane on the board is 50 mm x 50 mm. Thickness of copper layers are 36 m/18 m/18 m/36 m (1.5 oz./1 oz./1 oz./1.5 oz.). Ambient temperature in simulation is 22 C, still air. Power dissipation is 1W. The value of JA in LM2757 in micro SMD-12 could fall in a range as wide as 50C/W to 150C/W (if not wider), depending on PWB material, layout and environmental conditions. In applications where high maximum power dissipation exists (high VIN, high IOUT), special care must be paid to thermal dissipation issues. For more information on these topics, please refer to Application Note 1112: Micro SMD Wafer Level Chip Scale Package (SMD). Note 8: Min and Max limits are guaranteed by design, test, or statistical analysis. Typical numbers are not guaranteed, but do represent the most likely norm. Note 9: CIN, COUT, C1, C2: Low-ESR Surface-Mount Ceramic Capacitors (MLCCs) used in setting electrical characteristics. Note 10: Turn-on time is measured from when the M0 or M1 signal is pulled high until the output voltage crosses 90% of its final value. Note 11: There is a 450 k (typ.) pull-down resistor connected internally to each logic input. www.national.com 4 LM2757 Block Diagram 30033703 5 www.national.com LM2757 Typical Performance Characteristics Unless otherwise specified: VIN = 3.6V, V(M0) = 0V, V(M1) = VIN, C1 = C2 = 0.47F, CIN = COUT = 1.0F, TA = 25C. Capacitors are low-ESR multi-layer ceramic capacitors (MLCC's). Efficiency vs. Input Voltage, 5V Mode Efficiency vs. Input Voltage, 4.5V Mode 30033704 30033705 Efficiency vs. Input Voltage, 4.1V Mode Output Voltage vs. Output Current, 5V Mode 30033706 30033707 Output Voltage vs. Output Current, 4.5V Mode Output Voltage vs. Output Current, 4.1V Mode 30033708 www.national.com 30033709 6 Output Voltage vs. Input Voltage, 5V Mode 30033710 30033711 Output Voltage vs. Input Voltage, 4.5V Mode Output Voltage vs. Input Voltage, 4.1V Mode 30033712 30033713 Output Leakage Current, Device Shutdown Output Leakage Current, Device Shutdown 30033714 30033727 7 www.national.com LM2757 Output Voltage Ripple vs. Output Current, 5V Mode LM2757 Current Limit vs. Input Voltage Oscillator Frequency vs. Input Voltage 30033715 30033716 Operating Current vs. Input Voltage Shutdown Supply Current vs. Input Voltage 30033717 30033718 Startup Behavior, 5V Mode Line Step (3.5V to 4V) 30033720 Load = 200mA, VOUT = 5V Mode CH1: VIN; Scale: 1V/Div, DC Coupled CH2: VOUT; Scale: 100mV/Div, AC Coupled Time scale: 100s/Div 30033719 VIN = 3.6V, Load = 200mA CH2: VOUT; Scale: 1V/Div, DC Coupled CH4: IIN; Scale: 200mA/Div, DC Coupled Time scale: 100s/Div www.national.com 8 Load Step with a Li-Ion Battery 200mA to 10mA 30033721 30033722 VBATT = 4V, VOUT = 5V Mode CH1: VOUT; Scale: 50mV/Div, AC Coupled CH4: IOUT; Scale: 100mA/Div, DC Coupled Time scale: 10s/Div VBATT = 4V, VOUT = 5V Mode CH1: VOUT; Scale: 50mV/Div, AC Coupled CH4: IOUT; Scale: 100mA/Div, DC Coupled Time scale: 10s/Div 9 www.national.com LM2757 Load Step with a Li-Ion Battery, 10mA to 200mA LM2757 mode select pins. The voltage mode is selected according to the following table. Operation Description OVERVIEW The LM2757 is a switched capacitor converter that produces a regulated output voltage of either 5V, 4.5V or 4.1V depending on the mode selected. The core of the part is a highly efficient charge pump that utilizes fixed frequency pre-regulation to minimize ripple and power losses over wide input voltage and output current ranges. A description of the principal operational characteristics of the LM2757 is detailed in the Circuit Description, and Efficiency Performance sections. These sections refer to details in the Block Diagram. M1 Output Voltage Mode 0 0 Device Shutdown, Output High Impedance 0 1 5V 1 0 4.5V 1 1 4.1V SHUTDOWN WITH OUTPUT HIGH IMPEDANCE The LM2757 is in shutdown mode when there is a logic Low voltage on both mode select pins (M0, M1). There are also 450k pulldown resistors connected to both mode select pins, pulling the nodes down to ground when there is no signal present. When in shutdown, the output of the LM2757 is high impedance, allowing an external supply to drive the output line such as in USB OTG or mobile HDMI applications. Refer to the output leakage current graphs in the Typical Performance Characteristics section for typical leakage currents into the VOUT pin, when driven by a separate supply during shutdown. Output leakage increases with temperature, with the lowest leakage occurring at -30C and the highest leakage at 85C (on which the graph is based). It should be noted when looking at the graphs, as the input voltage falls the leakage peaks at around an input voltage of 1.5V, and then goes down as the input voltage goes to 0V. The leakage at an input voltage of 0V is the same as the leakage current when the battery is disconnected from the circuit. CIRCUIT DESCRIPTION The core of the LM2757 is a two-phase charge pump controlled by an internally generated non-overlapping clock. The charge pump operates by using external flying capacitors C1, C2 to transfer charge from the input to the output. At input voltages below 3.9V (typ.) for the 5V mode, the LM2757 operates in a 2x gain, with the input current being equal to 2x the load current. At input voltages above 3.9V (typ.) for the 5V mode, the part utilizes a gain of 3/2x, resulting in an input current equal to 3/2 times the load current. For the 4.5V mode, the LM2757 operates in a 2x gain when the input voltage is below 3.35V (typ.) and transitions to a 3/2x gain when the input voltage is above 3.35V (typ.). For the 4.1V mode, the device utilizes the 3/2x gain for the entire input voltage range. The two phases of the switched capacitor switching cycle will be referred to as the "phase one" and the "phase two". During phase one, one flying capacitor is charged by the input supply while the other flying capacitor is connected to the output and delivers charge to the load . After half of the switching cycle [ t = 1/(2xFSW) ], the LM2757 switches to phase two. In this configuration, the capacitor that supplied charge to the load in phase one is connected to the input to be recharged while the capacitor that had been charged in the previous phase is connected to the output to deliver charge. With this topology, output ripple is reduced by delivering charge to the output in every phase. The LM2757 uses fixed frequency pre-regulation to regulate the output voltage. The input and output connections of the flying capacitors are made with internal MOS switches. Preregulation limits the gate drive of the MOS switch connected between the voltage input and the flying capacitors. Controlling the on resistance of this switch limits the amount of charge transferred into and out of each flying capacitor during the charge and discharge phases, and in turn helps to keep the output ripple very low. SOFT START The LM2757 employs soft start circuitry to prevent excessive input inrush currents during startup. At startup, the output voltage gradually rises from 0V to the nominal output voltage. This occurs in 300s (typ.). Soft-start is engaged when the part is enabled. THERMAL SHUTDOWN Protection from damage related to overheating is achieved with a thermal shutdown feature. When the junction temperature rises to 145C (typ.), the part switches into shutdown mode. The LM2757 disengages thermal shutdown when the junction temperature of the part is reduced to 135C (typ.). Due to the high efficiency of the LM2757, thermal shutdown and/or thermal cycling should not be encountered when the part is operated within specified input voltage, output current, and ambient temperature operating ratings. If thermal cycling is seen under these conditions, the most likely cause is an inadequate PCB layout that does not allow heat to be sufficiently dissipated out of the device. EFFICIENCY PERFORMANCE Charge-pump efficiency is derived in the following two ideal equations (supply current and other losses are neglected for simplicity): CURRENT LIMIT PROTECTION The LM2757 charge pump contains current limit protection circuitry that protects the device during VOUT fault conditions where excessive current is drawn. Output current is limited to 250mA (typ). IIN = G x IOUT E = (VOUT x IOUT) / (VIN x IIN) = VOUT / (G x VIN) In the equations, G represents the charge pump gain. Efficiency is at its highest as GxVIN approaches VOUT. Refer to the efficiency graph in the Typical Performance Characteristics section for detailed efficiency data. The transition between gains of 3/2, and 2 are clearly distinguished by the sharp discontinuity in the efficiency curve. Application Information RECOMMENDED CAPACITOR TYPES The LM2757 requires 4 external capacitors for proper operation. Surface-mount multi-layer ceramic capacitors are recommended. These capacitors are small, inexpensive and have very low equivalent series resistance (ESR, 15m typ.). Tantalum capacitors, OS-CON capacitors, and aluminum electrolytic capacitors generally are not recommended ENABLE AND VOLTAGE MODE SELECTION The LM2757 is enabled when either one of the mode select pins (M0, M1) has a logic High voltage applied to it. There are 450k pulldown resistors connected internally to each of the www.national.com M0 10 Manufacturer INPUT CAPACITOR AND INPUT VOLTAGE RIPPLE The input capacitor (CIN) is a reservoir of charge that aids a quick transfer of charge from the supply to the flying capacitors during the charge phase of operation. The input capacitor helps to keep the input voltage from drooping at the start of the charge phase when the flying capacitors are connected to the input. It also filters noise on the input pin, keeping this noise out of sensitive internal analog circuitry that is biased off the input line. Much like the relationship between the output capacitance and output voltage ripple, input capacitance has a dominant and first-order effect on input ripple magnitude. Increasing (decreasing) the input capacitance will result in a proportional decrease (increase) in input voltage ripple. Input voltage, output current, and flying capacitance also will affect input ripple levels to some degree. In typical high-current applications, a 1.0F low-ESR ceramic capacitor is recommended on the input. Different input capacitance values can be used to reduce ripple, shrink the solution size, and/or cut the cost of the solution. But changing the input capacitor may also require changing the flying capacitor and/or output capacitor to maintain good overall circuit performance. Performance of the LM2757 with different capacitor setups is discussed below in Recommended Capacitor Configurations. Contact Information AVX www.avx.com Murata www.murata.com Taiyo-Yuden www.t-yuden.com TDK www.component.tdk.com Vishay-Vitramon www.vishay.com FLYING CAPACITORS The flying capacitors (C1, C2) transfer charge from the input to the output. Flying capacitance can impact both output current capability and ripple magnitudes. If flying capacitance is too small, the LM2757 may not be able to regulate the output voltage when load currents are high. On the other hand, if the flying capacitance is too large, the flying capacitor might overwhelm the input and output capacitors, resulting in increased input and output ripple. In typical high-current applications, 0.47F low-ESR ceramic capacitors are recommended for the flying capacitors. Polarized capacitors (tantalum, aluminum electrolytic, etc.) must not be used for the flying capacitor, as they could become reverse-biased during LM2757 operation. OUTPUT CAPACITOR AND OUTPUT VOLTAGE RIPPLE The output capacitor in the LM2757 circuit (COUT) directly impacts the magnitude of output voltage ripple. Other prominent factors also affecting output voltage ripple include input voltage, output current and flying capacitance. Due to the complexity of the regulation topology, providing equations or models to approximate the magnitude of the ripple can not be easily accomplished. But one important generalization can be made: increasing (decreasing) the output capacitance will result in a proportional decrease (increase) in output voltage ripple. 11 www.national.com LM2757 In typical high-current applications, a 1.0F low-ESR ceramic output capacitor is recommended. Different output capacitance values can be used to reduce ripple, shrink the solution size, and/or cut the cost of the solution. But changing the output capacitor may also require changing the flying capacitor and/or input capacitor to maintain good overall circuit performance. Performance of the LM2757 with different capacitor setups in discussed in the section Recommended Capacitor Configurations. High ESR in the output capacitor increases output voltage ripple. If a ceramic capacitor is used at the output, this is usually not a concern because the ESR of a ceramic capacitor is typically very low and has only a minimal impact on ripple magnitudes. If a different capacitor type with higher ESR is used (tantalum, for example), the ESR could result in high ripple. To eliminate this effect, the net output ESR can be significantly reduced by placing a low-ESR ceramic capacitor in parallel with the primary output capacitor. The low ESR of the ceramic capacitor will be in parallel with the higher ESR, resulting in a low net ESR based on the principles of parallel resistance reduction. for use with the LM2757 due to their high ESR, as compared to ceramic capacitors. For most applications, ceramic capacitors with an X7R or X5R temperature characteristic are preferred for use with the LM2757. These capacitors have tight capacitance tolerance (as good as 10%) and hold their value over temperature (X7R: 15% over -55C to 125C; X5R: 15% over -55C to 85C). Capacitors with a Y5V or Z5U temperature characteristic are generally not recommended for use with the LM2757. These types of capacitors typically have wide capacitance tolerance (+80%, -20%) and vary significantly over temperature (Y5V: +22%, -82% over -30C to +85C range; Z5U: +22%, -56% over +10C to +85C range). Under some conditions, a 1Frated Y5V or Z5U capacitor could have a capacitance as low as 0.1F. Such detrimental deviation is likely to cause Y5V and Z5U capacitors to fail to meet the minimum capacitance requirements of the LM2757. Net capacitance of a ceramic capacitor decreases with increased DC bias. This degradation can result in lower capacitance than expected on the input and/or output, resulting in higher ripple voltages and currents. Using capacitors at DC bias voltages significantly below the capacitor voltage rating will usually minimize DC bias effects. Consult capacitor manufacturers for information on capacitor DC bias characteristics. Capacitance characteristics can vary quite dramatically with different application conditions, capacitor types, and capacitor manufacturers. It is strongly recommended that the LM2757 circuit be thoroughly evaluated early in the design-in process with the mass-production capacitors of choice. This will help ensure that any such variability in capacitance does not negatively impact circuit performance. The voltage rating of the output capacitor should be 10V or more. For example, a 10V 0603 1.0F is acceptable for use with the LM2757, as long as the capacitance does not fall below a minimum of 0.5F in the intended application. All other capacitors should have a voltage rating at or above the maximum input voltage of the application. The capacitors should be selected such that the capacitance on the input does not fall below 0.7F, and the capacitance of the flying capacitors does not fall below 0.2F. The table below lists some leading ceramic capacitor manufacturers. LM2757 RECOMMENDED CAPACITANCE The data in Table 1 can be used to assist in the selection of capacitance for each node that best balances solution size and cost with the electrical requirements of the application. As previously discussed, input and output ripple voltages will vary with output current and input voltage. The numbers provided show expected ripple voltage with VIN = 3.6V and a load current of 200mA at 5V output, 100mA at 4.5V output, and 100mA at 4.1V output. The table offers a first look at approximate ripple levels and provides a comparison of different capacitance configurations, but is not intended to be a guarantee of performance. With any capacitance configuration chosen, always verify that the performance of the ripple waveforms are suitable for the intended application. The same capacitance value must be used for all the flying capacitors. For output regulation performance with different capacitor configurations, please refer to the Output Voltage vs. Input Voltage graphs in the Typical Performance Characteristics section of this datasheet. The output voltage regulation is typically better when using capacitors with a higher capacitance value and a higher voltage bias rating than the nominal voltage applied to them, as can be seen in the graphs, but this may have an impact in capacitor case size. For typical highcurrent small solution size applications, 1F capacitance X5R temperature characteristic rating 0402 (C1005) case size and 10V bias or higher capacitors can be used for the Input, Output and Flying capacitors. According to current capacitor offerings, there are no capacitors in the 0201 (C0603) case size that satisfy the minimum capacitance requirements of the LM2757 circuit. When selecting capacitors, it is preferred to use the ones with the highest voltage bias rating available from the capacitor supplier. Layout Guidelines Proper board layout will help to ensure optimal performance of the LM2757 circuit. The following guidelines are recommended: * Place capacitors as close to the LM2757 as possible, and preferably on the same side of the board as the IC. * Use short, wide traces to connect the external capacitors to the LM2757 to minimize trace resistance and inductance. * Use a low resistance connection between ground and the GND pin of the LM2757. Using wide traces and/or multiple vias to connect GND to a ground plane on the board is most advantageous. TABLE 1. LM2757 Performance with Different Capacitor Configurations (Note 12) Capacitor Configuration (VIN = 3.6V) Typical 5.0V, 200mA Output Ripple Typical 4.5V, 100mA Output Ripple Typical 4.1V, 100mA Output Ripple CIN = 1F, COUT = 1F, C1, C2 = 0.47F 32mV 12mV 11mV CIN = 0.68F, COUT = 1F, C1, C2 = 0.47F 32mV 11mV 11mV CIN = 0.68F, COUT = 0.47F, C1, C2 = 0.47F 51mV 15mV 15mV CIN = 0.68F, COUT = 0.47F, C1, C2 = 0.22F 53mV 18mV 18mV Note 12: Refer to the text in the Recommended Capacitor Configurations section for detailed information on the data in this table www.national.com 12 LM2757 Application Circuits USB OTG / Mobile HDMI POWER SUPPLY 30033724 The 5V output mode will normally be used for the USB OTG / Mobile HDMI application. Therefore the LM2757 can be enabled/disabled by applying a logic signal on only the M1 pin while grounding the M0 pin. Depending on the USB/HDMI mode of the application, the LM2757 can be enabled to drive SUPERCAPACITOR FLASH DRIVER the power bus line (Host), or disabled to put its output in high impedance allowing an external supply to drive the bus line (Slave). In addition to the high impedance-backdrive protection, the output current limit protection is 250mA (typ.), well within the USB OTG and HDMI requirements. 30033725 Using the 5V output voltage mode, the LM2757 can be used to charge a Supercapacitor for LED Flash applications while limiting the peak current drawn off the battery during the charge cycle. The LM2757 can be disabled for the Flash event, placing its output in high impedance with the input. In this way, all charge for the Flash LED(s) will come directly off the Supercapacitor and not load the main battery line. The LM2757 can be enabled/disabled by applying a logic signal on only the M1 pin while grounding the M0 pin. Special consideration must be taken when using Supercapicators for LED flash applications where the voltage on the capacitor is charged to a fixed value. This is due to the possible power management issues that could arise as a result of the high flash current and wide tolerance ranges (V-I characteristics) of typical Flash LEDs. If the voltage across the Flash LED(s) is not managed, damage could occur where a relatively low Vf LED is overdriven or places excessive voltage across the bottom control FET. To help reduce this issue, the use of a high power current sink is advised in applications where the forward voltage specification of the Flash LED has a wide range. 13 www.national.com LM2757 LED DRIVER 30033726 The 5.0V, 4.5V, or the 4.1V mode can be used depending on the forward voltage and load requirements of the LED application. The LM2757 can be enabled/disabled by applying the appropriate combination of logic signals on the M1 and M0 www.national.com pins. LED current for each string in this application is limited by the voltage across the string's ballast resistor, which is dependent on the output voltage mode selected and the V-I profile of each LED used. 14 LM2757 Physical Dimensions inches (millimeters) unless otherwise noted NSC Package TMD12AAA Micro SMD Wafer Level Package X1: 1215 m +/- 30 m X2: 1615 m +/- 30 m X3: 600 m +/- 75 m Bump pitch: 0.4 mm 15 www.national.com LM2757 Switched Capacitor Boost Regulator with High Impedance Output in Shutdown Notes For more National Semiconductor product information and proven design tools, visit the following Web sites at: Products Design Support Amplifiers www.national.com/amplifiers WEBENCH(R) Tools www.national.com/webench Audio www.national.com/audio App Notes www.national.com/appnotes Clock and Timing www.national.com/timing Reference Designs www.national.com/refdesigns Data Converters www.national.com/adc Samples www.national.com/samples Interface www.national.com/interface Eval Boards www.national.com/evalboards LVDS www.national.com/lvds Packaging www.national.com/packaging Power Management www.national.com/power Green Compliance www.national.com/quality/green Switching Regulators www.national.com/switchers Distributors www.national.com/contacts LDOs www.national.com/ldo Quality and Reliability www.national.com/quality LED Lighting www.national.com/led Feedback/Support www.national.com/feedback Voltage Reference www.national.com/vref Design Made Easy www.national.com/easy www.national.com/powerwise Solutions www.national.com/solutions Mil/Aero www.national.com/milaero PowerWise(R) Solutions Serial Digital Interface (SDI) www.national.com/sdi Temperature Sensors www.national.com/tempsensors SolarMagicTM www.national.com/solarmagic Wireless (PLL/VCO) www.national.com/wireless www.national.com/training PowerWise(R) Design University THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION ("NATIONAL") PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL'S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright(c) 2009 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Technical Support Center Email: support@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Technical Support Center Email: europe.support@nsc.com National Semiconductor Asia Pacific Technical Support Center Email: ap.support@nsc.com National Semiconductor Japan Technical Support Center Email: jpn.feedback@nsc.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated