SIDACtor(R) Device RoHS DO-214AA SIDACtor solid state protection devices protect telecommunications equipment such as modems, line cards, and CPE (telephones, answering machines, and fax machines). SIDACtor devices enable equipment to comply with various regulatory requirements including GR 1089, ITU K.20, K.21 and K.45, IEC 60950, UL 60950, and TIA-968-A (formerly known as FCC Part 68). Electrical Parameters Part Number * VDRM Volts VS Volts VT Volts IDRM Amps IS mAmps IT Amps IH mAmps 50 P0080S_L 6 25 4 5 800 2.2 P0220S_L 15 32 4 5 800 2.2 50 P0300S_L 25 40 4 5 800 2.2 50 P0640S_L 58 77 4 5 800 2.2 150 P0720S_L 65 88 4 5 800 2.2 150 P0900S_L 75 98 4 5 800 2.2 150 P1100S_L 90 130 4 5 800 2.2 150 P1300S_L 120 160 4 5 800 2.2 150 P1500S_L 140 180 4 5 800 2.2 150 P1800S_L 170 220 4 5 800 2.2 150 P2100S_L 180 240 4 5 800 2.2 150 P2300S_L 190 260 4 5 800 2.2 150 P2600S_L 220 300 4 5 800 2.2 150 P3100S_L 275 350 4 5 800 2.2 150 P3500S_L 320 400 4 5 800 2.2 150 * "L" in part number indicates RoHS compliance. For non-RoHS compliant device, delete "L" from part number. For individual "SA", "SB", and "SC" surge ratings, see table below. General Notes: * All measurements are made at an ambient temperature of 25 C. IPP applies to -40 C through +85 C temperature range. * IPP is a repetitive surge rating and is guaranteed for the life of the product. * Listed SIDACtor devices are bi-directional. All electrical parameters and surge ratings apply to forward and reverse polarities. * VDRM is measured at IDRM. * VS is measured at 100 V/s. * Special voltage (VS and VDRM) and holding current (IH) requirements are available upon request. Surge Ratings in Amps Series IPP 0.2x310 * 2x10 * 8x20 * 0.5x700 ** 2x10 ** 1.2x50 ** 10x160 * 10x160 ** 10x560 * 10x560 ** 5x320 * 9x720 ** Amps Amps Amps Amps Amps Amps A 20 150 150 90 50 B 25 250 250 150 100 C 50 500 400 200 150 200 10x360 * 10x1000 * 5x310 * ITSM 10x360 ** 10x1000 ** 10x700 ** 50 / 60 Hz Amps Amps 75 75 100 125 175 di/dt Amps Amps Amps/s 45 75 20 500 80 100 30 500 100 200 30 500 * Current waveform in s ** Voltage waveform in s www.littelfuse.com 3-2 (c) 2006 Littelfuse * Telecom Design Guide SIDACtor(R) Device Thermal Considerations Package Symbol DO-214AA TJ Operating Junction Temperature Range -40 to +150 C TS Storage Temperature Range -65 to +150 C 90 C/W RJA Parameter Thermal Resistance: Junction to Ambient Value Unit SIDACtor Devices Capacitance Values pF Part Number * P0080S[A/B]L P0080SCL P0220SAL P0220SBL P0220SCL P0300S[A/B]L P0300SCL P0640S[A/B]L P0640SCL P0720SAL P0720SBL P0720SCL P0900SAL P0900SBL P0900SCL P1100SAL P1100SBL P1100SCL P1300SAL P1300SBL P1300SCL P1500SAL P1500SBL P1500SCL P1800SAL P1800SBL P1800SCL P2100S[A/B]L P2100SCL P2300SAL P2300SBL P2300SCL P2600SAL P2600SBL P2600SCL P3100SAL P3100SBL P3100SCL P3500SAL P3500SBL P3500SCL MIN 25 35 25 25 30 15 25 40 55 35 35 50 35 35 45 30 30 45 25 25 40 25 25 35 25 25 35 20 30 25 25 30 20 20 30 20 20 30 20 20 25 MAX 150 260 150 150 240 140 250 60 155 60 75 150 55 70 140 50 70 115 45 60 105 40 55 95 35 50 90 35 90 35 50 80 35 45 80 35 45 70 35 40 65 * [A/B] in part number indicates that values are for both A and B surge ratings. Note: Off-state capacitance (CO) is measured at 1 MHz with a 2 V bias. Telecom Design Guide * (c) 2006 Littelfuse 3-3 www.littelfuse.com SIDACtor(R) Device IPP - Peak Pulse Current - %IPP +I IT IS IH IDRM -V +V VT VDRM VS Peak Value 100 tr = rise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 0 tr td t - Time (s) -I 14 12 10 IH 8 6 25 C 4 2 IH (TC = 25 C) tr x td Pulse Waveform Ratio of Percent of VS Change - % V-I Characteristics 0 -4 2.0 1.8 1.6 1.4 25 C 1.2 1.0 0.8 0.6 0.4 -40 -20 0 -6 -8 -40 -20 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - C 20 40 60 80 100 120 140 160 Junction Temperature (TJ) - C Normalized VS Change versus Junction Temperature www.littelfuse.com Normalized DC Holding Current versus Case Temperature 3-4 (c) 2006 Littelfuse * Telecom Design Guide