General Illumination LUXEON FlipChip UV Chip-scale package for maximum design flexibility in UV applications LUXEON FlipChip UV is the smallest and highest power density (W/cm2) ultraviolet with FlipChip Technology in a chip-scale package LED can be reflowed onto a substrate with a standard surface mount (SMT) equipment and process. LUXEON FlipChip UV LED enables tighter beam control and high packing density of LEDs on a chip-on-board solution and completely eliminates wire bonds in the system. LUXEON FlipChip UV is the ideal choice for cost sensitive applications to achieve high irradiance at high current density, maximizing W/$ by taking the advantage of lowest thermal resistance of a chip-scale package device. Features and BENEFITS Primary Applications Ultraviolet wavelength range of 380-410nm for a range of options Specialty Lighting Micro sized CSP: 1.0mm2 package for design flexibility and packing density No wire bonds allows for direct attach and reflow 5-sided emitter with batwing radiation pattern enables wide viewing angles Low thermal resistance for leading system level lm/$ Maximum drive current of 1A for delivers superior lumens for reduced LED count RoHS COMPLIANT DS137 LUXEON FlipChip UV Product Datasheet (c)2015 Lumileds Holding B.V. All rights reserved. Table of Contents General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Part Number Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Environmental Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Product Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Product Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Optical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Typical Performance Graphs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Binning Definitions & Labeling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Radiometric Flux Bins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Forward Voltage Bins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Peak Wavelength Bins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Reflow Soldering Guidelines (Based Upon SAC Solder) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 JEDEC Moisture Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Solder Pad Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Assembly Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Mechanical & Packaging Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Mechanical Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Packaging - Reel Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 DS137 LUXEON FlipChip UV Product Datasheet 20150217 (c)2015 Lumileds Holding B.V. All rights reserved. i General Information Part Number Nomenclature LUXEON FlipChip UV are specified and binned at 500mA and Tj=25C. The alphanumerical part number designations for the LUXEON FlipChip UV are explained as follows: LxF2 - Uyyy1000zzzz1 Where: x -- designates level (0 for die on blue bin tape, 1 for die on tape and reel) U -- designates for Ultraviolet color yyy -- designates minimum peak wavelength bin (390 for 390 nm minimum wavelength bin) 1000 -- designates die dimension (1000 for 1.000 mm2) zzzz -- designates minimum radiometric power at test conditions (0500 for 500mW power bin) Environmental Compliance Lumileds is committed to providing environmentally friendly products to the solid-state lighting market. LUXEON FlipChip White is compliant to the European Union directives on the restriction of hazardous substances in electronics equipment, namely the RoHS and REACH directives. Lumileds will not intentionally add the following restricted material to the LUXEON HIGH: lead, mercury, cadmium, hexavalent chromium, polybrominated biphyenyls (PBB) or polybrominated diphenyl ethers (PBDE). DS137 LUXEON FlipChip UV Product Datasheet 20150217 (c)2015 Lumileds Holding B.V. All rights reserved. 2 Product Characteristics (Tjunction = 25C) Product Selection Table 1. LUXEON FlipChip UV Typical Performance Peak Wavelength (500mA) Typical Radiometric Power [1, 2] (mW) Typical Vf (V) Part Number 500mA 1000mA 500mA 1000mA 380-390nm 250 350 450 473 662 852 3.2 3.2 3.2 3.3 3.3 3.3 LxF2-U380100002001 LxF2-U380100003001 LxF2-U380100004001 390-400nm 450 550 650 852 1042 1234 3.1 3.1 3.1 3.2 3.2 3.2 LxF2-U390100004001 LxF2-U390100005001 LxF2-U390100006001 400-410nm 550 650 750 1042 1232 1432 3.0 3.0 3.0 3.1 3.1 3.1 LxF2-U400100005001 LxF2-U400100006001 LxF2-U400100007001 Notes: 1. Lumileds maintains a tolerance of 10% on flux measurements. 2. Radiometric power value is based upon mounted die on highly reflective surface at Tj=25C. Optical Characteristics Table 2. LUXEON FlipChip UV Wavelength and Spectrum (at 500mA) Peak Wavelength [1] (nm) Part Number Wavelength Bin LxF2-U38010000xxxx1 Typical Spectra Half-Width (nm) Typical Temperature Coefficient of Peak Wavelength [2] (nm/C) Minimum Maximum 380-390 nm 380 390 23 0.05 LxF2-U39010000xxxx1 390-400 nm 390 400 23 0.05 LxF2-U40010000xxxx1 400-410 nm 400 410 23 0.05 Typical Thermal Resistance Junction to Solder Pad [2] (C/W) Notes for Table 2: 1. Lumileds maintains a tolerance of 2nm on peak wavelength measurements. 2. Measured between 25C and 85C at 500mA. Electrical Characteristics Table 3. LUXEON FlipChip UV Forward Voltage and Typical Thermal Resistance at 500mA Minimum Typical Maximum Typical Temperature Coefficient of Forward Voltage (mV/C) 380-390 nm 2.8 3.2 3.4 -2 to -3 2.0 LxF2-U39010000xxxx1 390-400 nm 2.8 3.1 3.4 -2 to -3 2.0 LxF2-U40010000xxxx1 400-410 nm 2.8 3.0 3.4 -2 to -3 2.0 Part Number Peak Wavelength LxF2-U38010000xxxx1 Forward Voltages [1] (V) Notes for Table 3: 1. Lumileds maintains a tolerance of 0.06V on forward voltage measurements. 2. Measured between Tj = 25C and Tj = 85C for coefficient of Vf . DS137 LUXEON FlipChip UV Product Datasheet 20150217 (c)2015 Lumileds Holding B.V. All rights reserved. 3 Absolute Maximum Ratings Table 4. LUXEON FlipChip UV Operating Condition and Ratings Parameter DC Forward Current Maximum Ratings 1000mA [1,2] Peak Pulsed Forward Current [1,3] 1200mA ESD Sensitivity [4] 200V Human Body Model (HBM) Class 3A, JESD22-A114-E LED Junction Temperature [1] (DC & pulse) 135C LED Operating Case Temperature [1] 105C Storage Temperature -40C - 135C Soldering Temperature 300 3C (<30 second) Allowable Reflow Cycles 3 Reserve Voltage (Vreverse) LUXEON FlipChip UV LEDs are not designed to be driven in reverse bias Notes for Table 4: 1. Proper current derating must be observed to maintain junction temperature below the maximum. 2. Residual periodic variations due to power conversion from alternating current (AC) to direct current (DC), also called "ripple", with frequencies 100Hz and amplitude 150mA are acceptable, assuming the average current throughout each cycle does not exceed the maximum allowable DC Forward Current at the corresponding maximum junction temperature. 3. Pulsed operation with a peak drive current equal to the stated Peak Pulsed Forward Current is acceptable if the pulse on-time is 5 ms per cycle and the duty cycle is 50%. 4. See LUXEON FlipChip Application Brief for additional information on ESD Protection DS137 LUXEON FlipChip UV Product Datasheet 20150217 (c)2015 Lumileds Holding B.V. All rights reserved. 4 Typical Performance Graphs Power Output (Test Current= 500mA) Figure 1. Typical radiometric power vs. Tjunction . Power Output (Tjunction=25C) Figure 2. Typical radiometric power vs. forward current. DS137 LUXEON FlipChip UV Product Datasheet 20150217 (c)2015 Lumileds Holding B.V. All rights reserved. 5 Wavelength Shift (Tjunction=25C) Figure 3. Typical peak wavelength shift vs. forward current. Wavelength Shift (Test Current =500mA) Figure 4. Typical peak wavelength shift vs. Tjunction . DS137 LUXEON FlipChip UV Product Datasheet 20150217 (c)2015 Lumileds Holding B.V. All rights reserved. 6 Forward Current (Tjunction=25C) Figure 5. Forward current vs. Vf . Spectral Distribution vs. Wavelength Characteristics (Tjunction=25C, Test Current =500mA) Figure 6. Spectral distribution vs. wavelength. DS137 LUXEON FlipChip UV Product Datasheet 20150217 (c)2015 Lumileds Holding B.V. All rights reserved. 7 Spatial Radiation Patterns (Tjunction=25C, Test Current =500mA) Figure 7. Intensity vs. angle. Figure 8. Angle vs. intensity. DS137 LUXEON FlipChip UV Product Datasheet 20150217 (c)2015 Lumileds Holding B.V. All rights reserved. 8 Binning Definitions & Labeling Purpose of Product Binning In the manufacturing of semiconductor products, there are variations in performance around the average values given in the technical datasheets. For this reason, Lumileds bins the LED components for radiometric power and forward voltage, peak wavelength. Decoding Product Bin Labeling LUXEON FlipChip UV emitters are labeled using a four-digit alphanumeric CAT code following the format below: ABCD Where: A -- Flux/Radiometric Bin (Z, A, B, C, etc.) B & C-- Wavelength Bin (Ax, Bx, Cx, Dx, etc.) D Vforward (8, 9, 0, 1, 2 etc.) -- Radiometric Flux Bins Table 5. Bin Code Radiometric Flux (mW) Minimum Maximum Z 200 250 A 250 300 B 300 350 C 350 400 D 400 450 E 450 500 F 500 550 G 550 600 H 600 650 I 650 700 J 700 750 K 750 800 DS137 LUXEON FlipChip UV Product Datasheet 20150217 (c)2015 Lumileds Holding B.V. All rights reserved. 9 Forward Voltage Bins Table 6. Bin Code Forward Voltage (V) Minimum Maximum 8 2.8 2.9 9 2.9 3.0 0 3.0 3.1 1 3.1 3.2 2 3.2 3.3 3 3.3 3.4 4 3.4 3.5 Peak Wavelength Bins Table 7. Bin Code Peak Wavelength (nm) Minimum Maximum Ax 380 385 Bx 385 390 Cx 390 395 Dx 395 400 Ex 400 405 Fx 405 410 Gx 410 415 DS137 LUXEON FlipChip UV Product Datasheet 20150217 (c)2015 Lumileds Holding B.V. All rights reserved. 10 Reflow Soldering Guidelines (Based Upon SAC Solder) Table 8. (Based upon SAC solder) Profile Feature Lead Free Assembly Average Ramp-Up Rate (Tsmax to Tp) 3C / second max Preheat Temperature Min (Tsmin ) 150C Preheat Temperature Max (Tsmax ) 200C Preheat Time (ts) from Tsmin to Tsmax 60 - 180 seconds Temperature ( TL ) 217C Time Maintained Above Temperature (tL ) 60 -150 seconds Peak / Classification Temperature (Tp ) 260C Time within 5C of Actual Temperature (tp ) 20 - 40 seconds Ramp-Down Rate 6C / second max Time 25C to Peak Temperature 8 minutes max Notes for Table 8: 1. All temperatures refer to the application Printed Circuit Board (PCB), measured on the surface adjacent to the package body. JEDEC Moisture Sensitivity Table 9. 1 Soak Requirements Floor Life Level Standard Time Conditions Time Conditions unlimited [ 30C / 85% RH 168 Hrs. + 5 / -0 Hrs. 85C / 85% RH DS137 LUXEON FlipChip UV Product Datasheet 20150217 (c)2015 Lumileds Holding B.V. All rights reserved. 11 Solder Pad Design Figure 9. Solder pad layout of LxF2-Uzzz1000yyyy1. Notes for Figure 9: 1. The drawing shows the recommended LUXEON FlipChip UV layout on Printed Circuit Board (PCB). 2. All dimensions are in millimeters. Assembly Precautions **Refer to Assembly Precautions and Material Safety documents DS137 LUXEON FlipChip UV Product Datasheet 20150217 (c)2015 Lumileds Holding B.V. All rights reserved. 12 Mechanical & Packaging Dimensions Mechanical Dimensions Figure 10. Mechanical dimensions for LxF2-Uxxx1000yyyy1. Notes for Figure 10: 1. Drawings are not scale. 2. All dimensions are in millimeters. DS137 LUXEON FlipChip UV Product Datasheet 20150217 (c)2015 Lumileds Holding B.V. All rights reserved. 13 Packaging - Pocket Tape Dimensions 1. Figure 11. Emitter pocket tape packaging. DS137 LUXEON FlipChip UV Product Datasheet 20150217 (c)2015 Lumileds Holding B.V. All rights reserved. 14 Packaging - Reel Dimensions Figure 12. Emitter reel packaging. DS137 LUXEON FlipChip UV Product Datasheet 20150217 (c)2015 Lumileds Holding B.V. All rights reserved. 15 About Lumileds Lumileds is the light engine leader, delivering innovation, quality, and reliability. For 100 years, Lumileds commitment to innovation has helped customers pioneer breakthrough products in the automotive, consumer and illumination markets. Lumileds is shaping the future of light with our LEDs and automotive lamps, and helping our customers illuminate how people see the world around them. To learn more about our portfolio of light engines visit www.lumileds.com. (c)2015 Lumileds Holding B.V. All rights reserved. LUXEON is a registered trademark of the Lumileds Holding B.V. in the United States and other countries. www.lumileds.com DS137 LUXEON FlipChip UV Product Datasheet 20150217 Neither Lumileds Holding B.V. nor its affiliates shall be liable for any kind of loss of data or any other damages, direct, indirect or consequential, resulting from the use of the provided information and data. Although Lumileds Holding B.V. and/or its affiliates have attempted to provide the most accurate information and data, the materials and services information and data are provided "as is," and neither Lumileds Holding B.V. nor its affiliates warrants or guarantees the contents and correctness of the provided information and data. Lumileds Holding B.V. and its affiliates reserve the right to make changes without notice. You as user agree to this disclaimer and user agreement with the download or use of the provided materials, information and data. Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Lumileds: L1F2-U400100007001 L1F2-U390100006001 L1F2-U400100006001 L1F2-U380100002001 L1F2-U380100003001 L1F2-U390100004001 L1F2-U380100004001 L1F2-U400100005001 L1F2-U390100005001