TPS62260, TPS62261 TPS62262, TPS62263 SLVS763D - JUNE 2007 - REVISED FEBRUARY 2011 www.ti.com 2.25 MHz 600 mA Step Down Converter in 2x2 QFN / TSOT-23 Package Check for Samples: TPS62260, TPS62261, TPS62262, TPS62263 FEATURES 1 * * * 2 * * * * * * * * * High Efficiency Step-Down Converter Output Current up to 600 mA VIN Range from 2 V to 6 V for Li-ion Batteries with Extended Voltage Range 2.25 MHz Fixed Frequency Operation Power Save Mode at Light Load Currents Output Voltage Accuracy in PWM mode 1.5% Typ. 15 A Quiescent Current 100% Duty Cycle for Lowest Dropout Soft Start Voltage Positioning at Light Loads Available in a small 2x2x0.8mm QFN and TSOT-23 package Allows <1mm Solution Height The TPS62260 device is a highly efficient synchronous step down dc-dc converter optimized for battery powered applications. It provides up to 600-mA output current from a single Li-Ion cell and is ideal to power mobile phones and other portable applications. With an wide input voltage range of 2 V to 6 V, the device supports applications powered by Li-Ion batteries with extended voltage range, two and three cell alkaline batteries, 3.3 V and 5 V input voltage rails. The TPS62260 operates at 2.25 MHz fixed switching frequency and enters Power Save Mode operation at light load currents to maintain high efficiency over the entire load current range. The Power Save Mode is optimized for low output voltage ripple. For low noise applications, the device can be forced into fixed frequency PWM mode by pulling the MODE pin high. In the shutdown mode, the current consumption is reduced to less than 1A. TPS62260 allows the use of small inductors and capacitors to achieve a small solution size. APPLICATIONS * * * * DESCRIPTION PDAs, Pocket PCs Low Power DSP Supply Portable Media Players POL applications The TPS62260 is available in a very small 2x2 6 pin QFN and TSOT-23 5 pin package. TPS62260DRV VIN CIN L 2.2 mH SW R1 EN 4.7 mF GND MODE C1 22 pF Up to 600mA VOUT 100 COUT 80 VIN = 3 V 10 mF FB 70 R2 VIN = 2.3 V 90 VIN = 2.7 V Efficiency - % VIN = 2V to 6V 60 VIN = 3.6 V VIN = 4.5 V 50 40 30 20 10 0 0.01 VOUT = 1.8 V, MODE = GND, L = 2.2 mH, DCR 110 mR 0.1 1 10 100 IO - Output Current - mA 1000 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PowerPAD is a trademark of Texas Instruments. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. (c) 2007-2011, Texas Instruments Incorporated TPS62260, TPS62261 TPS62262, TPS62263 SLVS763D - JUNE 2007 - REVISED FEBRUARY 2011 www.ti.com This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. ORDERING INFORMATION TA PART NUMBER OUTPUT VOLTAGE (1) TPS62260 Adjustable TPS62261 -40C to 85C (1) (2) PACKAGE (2) PACKAGE DESIGNATOR MODE PIN PACKAGE MARKING QFN 2x2-6 DRV Yes BYK TSOT-23 5 DDC No, PFM/PWM auto transition BYP 1.8V fixed QFN 2x2-6 DRV Yes BYL QFN 2x2-6 DRV Yes BYM TPS62262 1.2V fixed TSOT-23 5 DDC No, PFM/PWM auto transition QXS TPS62263 2.5V fixed QFN 2x2-6 DRV Yes CFX Contact TI for other fixed output voltage options For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI website at www.ti.com. ABSOLUTE MAXIMUM RATINGS over operating free-air temperature range (unless otherwise noted) (1) VALUE Input voltage range (2) UNIT -0.3 to 7 -0.3 to VIN +0.3, 7 Voltage range at EN, MODE V -0.3 to 7 Voltage on SW Peak output current Internally limited ESD rating (3) HBM Human body model 2 CDM Charge device model 1 Machine model A kV 200 V TJ Maximum operating junction temperature -40 to 125 C Tstg Storage temperature range -65 to 150 C (1) (2) (3) Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated under recommended operating conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. All voltage values are with respect to network ground terminal. The human body model is a 100-pF capacitor discharged through a 1.5-k resistor into each pin. The machine model is a 200-pF capacitor discharged directly into each pin. DISSIPATION RATINGS PACKAGE RJA POWER RATING FOR TA 25C DERATING FACTOR ABOVE TA = 25C DRV 76C/W 1300 mW 13 mW/C DDC 250/C 400 mW 4 mW/C RECOMMENDED OPERATING CONDITIONS MIN VIN MAX UNIT 2 6 Output voltage range for adjustable voltage 0.6 VIN V TA Operating ambient temperature -40 85 C TJ Operating junction temperature -40 125 C 2 Supply voltage NOM Submit Documentation Feedback V (c) 2007-2011, Texas Instruments Incorporated Product Folder Link(s): TPS62260 TPS62261 TPS62262 TPS62263 TPS62260, TPS62261 TPS62262, TPS62263 SLVS763D - JUNE 2007 - REVISED FEBRUARY 2011 www.ti.com ELECTRICAL CHARACTERISTICS Over full operating ambient temperature range, typical values are at TA = 25C. Unless otherwise noted, specifications apply for condition VIN = EN = 3.6V. External components CIN = 4.7F 0603, COUT = 10F 0603, L = 2.2H, see the parameter measurement information. PARAMETER TEST CONDITIONS MIN TYP MAX UNIT SUPPLY VIN Input voltage range IOUT Output current 2.3 6 VIN 2.5 V to 6 V 600 VIN 2.3 V to 2.5 V 300 VIN 2 V to 2.3 V 150 IOUT = 0 mA, PFM mode enabled (MODE = GND) device not switching IQ Operating quiescent current Shutdown current UVLO A IOUT = 0 mA, PFM mode enabled (MODE = GND) device switching, VOUT = 1.8 V, See (1) 18.5 3.8 EN = GND Undervoltage lockout threshold mA 15 IOUT = 0 mA, switching with no load (MODE = VIN), PWM operation, VOUT = 1.8 V, VIN = 3 V ISD V 0.1 Falling 1.85 Rising 1.95 mA 1 A V ENABLE, MODE VIH High level input voltage, EN, MODE 2 V VIN 6 V 1 VIN VIL Low level input voltage, EN, MODE 2 V VIN 6 V 0 0.4 IIN Input bias current, EN, MODE EN, MODE = GND or VIN 0.01 1 240 480 185 380 1 1.2 V V A POWER SWITCH RDS(on) ILIMF TSD High side MOSFET on-resistance Low side MOSFET on-resistance VIN = VGS = 3.6 V, TA = 25C Forward current limit MOSFET high-side and low side VIN = VGS = 3.6 V Thermal shutdown Increasing junction temperature 140 Thermal shutdown hysteresis Decreasing junction temperature 20 0.8 m A C OSCILLATOR fSW 2 V VIN 6 V Oscillator frequency 2 2.25 2.5 MHz VIN V OUTPUT VOUT Adjustable output voltage range Vref Reference voltage 0.6 600 Feedback voltage PWM Mode MODE = VIN, PWM operation, for fixed output voltage versions VFB = VOUT, 2.5 V VIN 6 V, 0 mA IOUT 600 mA (2) Feedback voltage PFM mode MODE = GND, device in PFM mode, voltage positioning active (1) 1% Load regulation PWM Mode -0.5 tStart Up Start-up time Time from active EN to reach 95% of VOUT nominal 500 tRamp VOUT ramp up time Time to ramp from 5% to 95% of VOUT Ilkg Leakage current into SW pin VIN = 3.6 V, VIN = VOUT = VSW, EN = GND VFB (1) (2) (3) -1.5% 0% mV 1.5% %/A s s 250 (3) 0.1 1 A In PFM mode, the internal reference voltage is set to typ. 1.01xVref. See the parameter measurement information. For VIN = VO + 0.6 V In fixed output voltage versions, the internal resistor divider network is disconnected from FB pin. (c) 2007-2011, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TPS62260 TPS62261 TPS62262 TPS62263 3 TPS62260, TPS62261 TPS62262, TPS62263 SLVS763D - JUNE 2007 - REVISED FEBRUARY 2011 www.ti.com PIN ASSIGNMENTS DDC PACKAGE (TOP VIEW) VIN GND EN SW 5 1 DRV PACKAGE (TOP VIEW) 1 SW MODE FB 2 3 FB 4 3 2 we Po 6 AD P 5 r 4 GND VIN EN TERMINAL FUNCTIONS TERMINAL NO. QFN 2x2-6 NO. TSOT23-5 I/O VIN 5 1 PWR VIN power supply pin. GND 6 2 PWR GND supply pin EN 4 3 I SW 1 5 OUT FB 3 4 I Feedback Pin for the internal regulation loop. Connect the external resistor divider to this pin. In case of fixed output voltage option, connect this pin directly to the output capacitor MODE 2 I This pin is only available at QFN package option. MODE pin = high forces the device to operate in fixed frequency PWM mode. MODE pin = low enables the Power Save Mode with automatic transition from PFM mode to fixed frequency PWM mode. NAME DESCRIPTION This is the enable pin of the device. Pulling this pin to low forces the device into shutdown mode. Pulling this pin to high enables the device. This pin must be terminated. This is the switch pin and is connected to the internal MOSFET switches. Connect the external inductor between this terminal and the output capacitor. FUNCTIONAL BLOCK DIAGRAM VIN CurrentLimit Comparator Thermal Shutdown VIN Undervoltage Lockout 1.8 V Limit High Side EN PFM Comparator +1% Voltage positioning Reference 0.6 V VREF FB VREF +1% Only in 2x2SON MODE MODE Softstart VOUT RAMP CONTROL Error Amplifier Control Stage Gate Driver AntiShoot-Through SW1 VREF Integrator FB FB Zero-Pole Amp. PWM Comp. Limit Low Side RI 1 RI3 RI..N Sawtooth Generator Int. Resistor Network GND CurrentLimit Comparator 2.25-MHz Oscillator GND 4 Submit Documentation Feedback (c) 2007-2011, Texas Instruments Incorporated Product Folder Link(s): TPS62260 TPS62261 TPS62262 TPS62263 TPS62260, TPS62261 TPS62262, TPS62263 SLVS763D - JUNE 2007 - REVISED FEBRUARY 2011 www.ti.com PARAMETER MEASUREMENT INFORMATION TPS62260DVR V IN CIN L 2.2 mH SW R1 EN 4.7 mF GND VOUT C1 22 pF 10 mF FB MODE COUT R2 L: LPS3015 2.2 mH, 110 mW CIN GRM188R60J475K 4.7 mF Murata 0603 size COUT GRM188R60J106M 10 mF Murata 0603 size TYPICAL CHARACTERISTICS Table 1. Table of Graphs FIGURE Efficiency Output Voltage Accuracy Typical Operation Mode Transition Output Current VOUT = 1.8 V, Power Save Mode, MODE = GND Figure 1 Output Current VOUT = 1.8 V, PWM Mode, MODE = VIN Figure 2 Output Current VOUT = 3.3 V, PWM Mode, MODE = VIN Figure 3 Output Current VOUT = 3.3 V, Power Save Mode, MODE = GND Figure 4 Output Current Figure 5 Output Current Figure 6 at 25C, VOUT = 1.8 V, Power Save Mode, MODE = GND Figure 7 at -40C, VOUT = 1.8 V, Power Save Mode, MODE = GND Figure 8 at 85C, VOUT = 1.8 V, Power Save Mode, MODE = GND Figure 9 at 25C, VOUT = 1.8 V, PWM Mode, MODE = VIN Figure 10 at -40C, VOUT = 1.8 V, PWM Mode, MODE = VIN Figure 11 at 85C, VOUT = 1.8 V, PWM Mode, MODE = VIN Figure 12 PWM Mode, VOUT = 1.8 V Figure 13 MODE Pin Transition From PFM to PWM Mode at light load Figure 14 MODE Pin Transition From PWM to PFM Mode at light load Figure 15 Start-up Timing Figure 16 Forced PWM Mode , VOUT = 1.5 V, 50 mA to 200 mA Figure 17 Forced PWM Mode , VOUT = 1.5 V, 200 mA to 400 mA Figure 18 PFM Mode to PWM Mode, VOUT = 1.5 V, 150 A to 400 mA Figure 19 PWM Mode to PFM Mode, VOUT = 1.5 V, 400 mA to 150 A Figure 20 PFM Mode, VOUT = 1.5 V, 1.5 mA to 50 mA Figure 21 PFM Mode, VOUT = 1.5 V, 50 mA to 1.5 mA Figure 22 PFM Mode to PWM Mode, VOUT = 1.8 V, 50 mA to 250 mA Figure 23 PFM Mode to PWM Mode, VOUT = 1.5 V, 50 mA to 400 mA Figure 24 PWM Mode to PFM Mode, VOUT = 1.5 V, 400 mA to 50 mA Figure 25 PFM Mode, VOUT = 1.8 V, 50 mA Figure 26 Forced PWM Mode, VOUT = 1.8 V, 250 mA Figure 27 PFM VOUT Ripple, VOUT = 1.8 V, 10 mA, L = 2.2H, COUT = 10F Figure 28 PFM VOUT Ripple, VOUT = 1.8 V, 10 mA, L = 4.7H, COUT = 10F Figure 29 Shutdown Current into VIN vs Input Voltage, (TA = 85C, TA = 25C, TA = -40C) Figure 30 Quiescent Current vs Input Voltage, (TA = 85C, TA = 25C, TA = -40C) Figure 31 Load Transient Line Transient Typical Operation (c) 2007-2011, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TPS62260 TPS62261 TPS62262 TPS62263 5 TPS62260, TPS62261 TPS62262, TPS62263 SLVS763D - JUNE 2007 - REVISED FEBRUARY 2011 www.ti.com TYPICAL CHARACTERISTICS (continued) Table 1. Table of Graphs (continued) FIGURE Static Drain Source On-State Resistance vs Input Voltage, (TA = 85C, TA = 25C, TA = -40C) 100 100 90 90 80 80 70 70 60 50 40 30 10 VIN = 3 V 60 1 10 100 1000 VIN = 4.5 V 40 20 VOUT = 1.8 V, MODE = VIN, 10 L = 2.2 mH IO - Output Current - mA 1 10 100 IO - Output Current - mA Figure 1. Figure 2. EFFICIENCY (PWM Mode) vs OUTPUT CURRENT EFFICIENCY (Power Save Mode) vs OUTPUT CURRENT VIN = 4.2 V 80 90 60 h - Efficiency - % VIN = 5 V VIN = 4.5 V 50 40 VOUT = 3.3 V MODE = VIN L = 2.2 mH DCR 110 mW COUT = 10 mF 0603 30 20 10 1 VIN = 3.6 V VIN = 5 V 10 100 IOUT - Output Current - mA Figure 3. Submit Documentation Feedback 70 VIN = 4.5 V 60 50 40 VOUT = 3.3 V MODE = GND L = 2.2 mH DCR = 110 mH COUT = 10 mF 0603 30 20 10 0 1000 1000 VIN = 4.2 V 80 VIN = 3.6 V 70 VIN = 3.6 V 50 100 90 h - Efficiency - % VIN = 2.7 V 0 0.1 100 6 VIN = 2.3 V 30 VOUT = 1.8 V MODE = GND L = 2.2 mH DCR 110 mR 20 Figure 33 EFFICIENCY (PWM Mode) vs OUTPUT CURRENT h - Efficiency - % Efficiency - % EFFICIENCY (Power Save Mode) vs OUTPUT CURRENT 0 0.01 Figure 32 0 0.01 0.1 1 10 100 1000 IOUT - Output Current - mA Figure 4. (c) 2007-2011, Texas Instruments Incorporated Product Folder Link(s): TPS62260 TPS62261 TPS62262 TPS62263 TPS62260, TPS62261 TPS62262, TPS62263 SLVS763D - JUNE 2007 - REVISED FEBRUARY 2011 www.ti.com EFFICIENCY vs OUTPUT CURRENT EFFICIENCY vs OUTPUT CURRENT 100 100 90 70 80 VI = 2.3 V 60 VI = 4.5 V 50 VI = 3.6 V 40 30 VO = 1.2 V, MODE = VI, 20 10 100 0 0.01 1000 0.1 1 10 100 1000 IO - Output Current - mA Figure 5. Figure 6. OUTPUT VOLTAGE ACCURACY vs OUTPUT CURRENT OUTPUT VOLTAGE ACCURACY (Power Save Mode) vs OUTPUT CURRENT 1.88 1.86 PFM Mode, Voltage Positioning VO - Output Voltage DC - V VO - Output Voltage DC - V VO = 1.2 V MODE = GND L = 2 mH MIPSA2520 CO = 10 mF 0603 IO - Output Current - mA 1.86 1.84 1.82 1.8 1.76 VI = 2.7 V 40 10 1.88 1.78 50 20 0 10 VI = 3.6 V 60 30 L = 2 mH, MIPSA2520 CO = 10 mF 0603 1 VI = 4.5 V 70 VI = 2.3 V Efficiency - % 80 Efficiency - % 90 VI = 2.3 V VI = 2.7 V TA = 25C VOUT = 1.8 V MODE = GND L = 2.2 mH CO = 10 mF 1.74 0.01 0.1 1.84 1.82 1.8 1.78 1.76 1 10 IO - Output Current - mA Figure 7. (c) 2007-2011, Texas Instruments Incorporated 100 1000 1.74 0.01 TA = -40C VOUT = 1.8 V MODE = GND L = 2.2 mH CO = 10 mF 0.1 1 10 100 1000 IO - Output Current - mA Figure 8. Submit Documentation Feedback Product Folder Link(s): TPS62260 TPS62261 TPS62262 TPS62263 7 TPS62260, TPS62261 TPS62262, TPS62263 SLVS763D - JUNE 2007 - REVISED FEBRUARY 2011 www.ti.com OUTPUT VOLTAGE ACCURACY (Power Save Mode) vs OUTPUT CURRENT OUTPUT VOLTAGE ACCURACY (PWM Mode) vs OUTPUT CURRENT 1.854 1.88 1.836 VO - Output Voltage DC - V VO - Output Voltage DC - V 1.86 1.84 1.82 1.8 TA = 85C VOUT = 1.8 V MODE = GND L = 2.2 mH CO = 10 mF 1.78 1.76 1.74 0.01 0.1 TA = 25C, VOUT = 1.8 V, MODE = VIN, L = 2.2 mH 1.818 1.8 VIN = 2.3 V VIN = 2.7 V VIN = 3 V VIN = 3.6 V VIN = 4.5 V 1.782 1.764 1 10 100 1.746 0.01 1000 0.1 OUTPUT VOLTAGE ACCURACY (PWM Mode) vs OUTPUT CURRENT OUTPUT VOLTAGE ACCURACY (PWM Mode) vs OUTPUT CURRENT 1000 1.854 TA = -40C, VOUT = 1.8 V, MODE = VIN, 1.836 VO - Output Voltage DC - V VO - Output Voltage DC - V 100 Figure 10. L = 2.2 mH 1.818 1.8 VIN = 2 V VIN = 2.7 V VIN = 3 V VIN = 3.6 V VIN = 4.5 V 1.782 1.764 1.746 0.01 0.1 1 10 Figure 11. Submit Documentation Feedback TA = 85C, VOUT = 1.8 V, MODE = VIN, L = 2.2 mH 1.818 1.8 VIN = 2.3 V VIN = 2.7 V VIN = 3 V VIN = 3.6 V VIN = 4.5 V 1.782 1.764 IO - Output Current - mA 8 10 Figure 9. 1.854 1.836 1 IO - Output Current - mA IO - Output Current - mA 100 1000 1.746 0.01 0.1 1 10 100 1000 IO - Output Current - mA Figure 12. (c) 2007-2011, Texas Instruments Incorporated Product Folder Link(s): TPS62260 TPS62261 TPS62262 TPS62263 TPS62260, TPS62261 TPS62262, TPS62263 SLVS763D - JUNE 2007 - REVISED FEBRUARY 2011 www.ti.com MODE PIN TRANSITION FROM PFM TO FORCED PWM MODE AT LIGHT LOAD TYPICAL OPERATION (PWM Mode) VIN 3.6V VOUT 1.8V, IOUT 150mA L 2.2mH, COUT 10mF 0603 VOUT 10 mV/Div VIN = 3.6 V VOUT = 1.8 V IOUT = 10 mA MODE 2V/Div SW 2 V/Div SW 2V/Div PFM Mode Forced PWM Mode ICOIL 200 mA/Div Icoil 200mA/Div Time Base - 1 ms/Div Time Base - 10 ms/Div Figure 13. Figure 14. MODE PIN TRANSITION FROM PWM TO PFM MODE AT LIGHT LOAD START-UP TIMING MODE 2 V/Div VIN = 3.6 V VOUT = 1.8 V IOUT = 10 mA SW 2 V/Div EN 2 V/Div VIN = 3.6 V RLoad = 10 VOUT = 1.8 V IIN into CIN MODE = GND SW 2 V/Div PFM Mode Forced PWM Mode VOUT 2 V/Div ICOIL 200 mA/Div IIN 100 mA/Div Time Base - 2.5 ms/Div Figure 15. (c) 2007-2011, Texas Instruments Incorporated Time Base - 100 ms/Div Figure 16. Submit Documentation Feedback Product Folder Link(s): TPS62260 TPS62261 TPS62262 TPS62263 9 TPS62260, TPS62261 TPS62262, TPS62263 SLVS763D - JUNE 2007 - REVISED FEBRUARY 2011 LOAD TRANSIENT (Forced PWM Mode) VIN 3.6 V VOUT 1.5 V IOUT 50 mA to 200 mA MODE = VIN VOUT 50 mV/Div www.ti.com LOAD TRANSIENT (Forced PWM Mode) VIN 3.6 V VOUT 1.5 V IOUT 200 mA to 400 mA VOUT 50 mV/Div IOUT 200 mA/Div 400 mA 200 mA IOUT 200 mA/Div ICOIL 500 mA/Div ICOIL 500 mA/Div Time Base - 20 ms/Div Time Base - 20 ms/Div Figure 17. Figure 18. LOAD TRANSIENT (PFM Mode To PWM Mode) LOAD TRANSIENT (PWM Mode To PFM Mode) SW 2 V/Div SW 2 V/Div VOUT 50mV/Div VIN 3.6 V VOUT 1.5 V IOUT 150 mA to 400 mA MODE = GND 400 mA IOUT 500 mA/Div VIN 3.6 V VOUT 1.5 V IOUT 150 mA to 400 mA MODE = GND VOUT 50 mV/Div 400 mA IOUT 500 mA/Div 150 mA 150 mA ICOIL500 mA/Div ICOILl 500mA/Div Time Base - 500 ms/Div Figure 19. 10 Submit Documentation Feedback Time Base - 500 ms/Div Figure 20. (c) 2007-2011, Texas Instruments Incorporated Product Folder Link(s): TPS62260 TPS62261 TPS62262 TPS62263 TPS62260, TPS62261 TPS62262, TPS62263 SLVS763D - JUNE 2007 - REVISED FEBRUARY 2011 www.ti.com LOAD TRANSIENT (PFM Mode) LOAD TRANSIENT (PFM Mode) SW 2 V/Div VIN 3.6 V VOUT 1.5 V IOUT 1.5 mA to 50 mA MODE = GND SW 2 V/Div VIN 3.6 V VOUT 1.5 V IOUT 50 mA to 1.5mA MODE = GND VOUT 50 mV/Div VOUT 50mV/Div 50 mA 50 mA IOUT 50 mA/Div IOUT 50 mA/Div 1.5 mA 1.5 mA ICOIL 500 mA/Div ICOIL 500 mA/Div Time Base - 50 ms/Div Time Base - 50 ms/Div Figure 21. Figure 22. LOAD TRANSIENT (PFM Mode To PWM Mode) LOAD TRANSIENT (PFM Mode To PWM Mode) SW 2 V/Div SW 2 V/Div VIN 3.6 V VOUT 1.5 V IOUT 50 mA to 400 mA MODE = GND VOUT 50 mV/Div VIN 3.6 V VOUT 1.8 V IOUT 50 mA to 250 mA MODE = GND VOUT 50 mV/Div 250 mA IOUT 200 mA/Div 50 mA PWM Mode PFM Mode 400 mA IOUT 500 mA/Div 50 mA ICOIL 500 mA/Div ICOIL 500mA/Div Time Base - 20 ms/Div Figure 23. (c) 2007-2011, Texas Instruments Incorporated Time Base - 20 ms/Div Figure 24. Submit Documentation Feedback Product Folder Link(s): TPS62260 TPS62261 TPS62262 TPS62263 11 TPS62260, TPS62261 TPS62262, TPS62263 SLVS763D - JUNE 2007 - REVISED FEBRUARY 2011 www.ti.com LOAD TRANSIENT (PWM Mode To PFM Mode) LINE TRANSIENT (PFM Mode) SW 2 V/Div VIN 3.6V to 4.2V 500 mV/Div VIN 3.6 V VOUT 1.5 V IOUT 50 mA to 400 mA MODE = GND VOUT 50 mV/Div PFM Mode PWM Mode 400 mA IOUT 500 mA/Div 50 mA VOUT = 1.8 V 50 mV/Div IOUT = 50 mA MODE = GND ICOIL 500 mA/Div Time Base - 20 ms/Div Figure 25. Figure 26. LINE TRANSIENT (Forced PWM Mode) TYPICAL OPERATION (PFM Mode) VOUT 20 mV/Div VIN 3.6V to 4.2V 500 mV/Div SW 2 V/Div VOUT = 1.8 V 50 mV/Div IOUT = 250 mA MODE = VIN ICOIL 200 mA/Div Time Base - 100ms/Div Figure 27. 12 Submit Documentation Feedback Time Base - 10 ms/Div Figure 28. (c) 2007-2011, Texas Instruments Incorporated Product Folder Link(s): TPS62260 TPS62261 TPS62262 TPS62263 TPS62260, TPS62261 TPS62262, TPS62263 SLVS763D - JUNE 2007 - REVISED FEBRUARY 2011 www.ti.com SHUTDOWN CURRENT INTO VIN vs INPUT VOLTAGE TYPICAL OPERATION (PFM Mode) 0.8 VIN 3.6 V; VOUT 1.8 V, IOUT 10 mA, L = 4.7 mH, COUT = 10 mF 0603, MODE = GND EN = GND ISD - Shutdown Current Into VIN - mA VOUT 20 mV/Div SW 2 V/Div ICOIL 200 mA/Div Time Base - 2 ms/Div 0.7 0.6 o TA = 85 C 0.5 0.4 0.3 0.2 o o TA = 25 C TA = -40 C 0.1 0 2 2.5 3 3.5 4 4.5 5 5.5 6 VIN - Input Voltage - V Figure 30. QUIESCENT CURRENT vs INPUT VOLTAGE STATIC DRAIN-SOURCE ON-STATE RESISTANCE vs INPUT VOLTAGE 20 o TTAA == 85 85C IQ - Quiescent Current - mA IQ - Quiescent Current - mA 18 MODE == GND, GND MODE EN == VIN, VIN EN Device Not Not Switching Switching Device 16 o C TTAA = 25 C 14 12 C TTAA == -40 -40oC 10 8 8 222 2.5 3 3.5 44 4.5 4.5 V VIN InputVoltage Voltage--VV IN--Input Figure 31. (c) 2007-2011, Texas Instruments Incorporated 55 5.5 5.5 66 RDS(on) - Static Drain-Source On-State Resistance - W Figure 29. 0.8 High Side Switching 0.7 0.6 o TA = 85 C 0.5 o TA = 25 C 0.4 0.3 0.2 o TA = -40 C 0.1 0 2 2.5 3 3.5 4 4.5 5 VIN - Input Voltage - V Figure 32. Submit Documentation Feedback Product Folder Link(s): TPS62260 TPS62261 TPS62262 TPS62263 13 TPS62260, TPS62261 TPS62262, TPS62263 RDS(on) - Static Drain-Source On-State Resistance - W SLVS763D - JUNE 2007 - REVISED FEBRUARY 2011 14 Submit Documentation Feedback www.ti.com STATIC DRAIN-SOURCE ON-STATE RESISTANCE vs INPUT VOLTAGE 0.4 Low Side Switching 0.35 0.3 o TA = 85 C 0.25 o TA = 25 C 0.2 0.15 0.1 o TA = -40 C 0.05 0 2 2.5 3 3.5 4 4.5 5 VIN - Input Voltage - V Figure 33. (c) 2007-2011, Texas Instruments Incorporated Product Folder Link(s): TPS62260 TPS62261 TPS62262 TPS62263 TPS62260, TPS62261 TPS62262, TPS62263 SLVS763D - JUNE 2007 - REVISED FEBRUARY 2011 www.ti.com DETAILED DESCRIPTION OPERATION The TPS62260 step down converter operates with typically 2.25 MHz fixed frequency pulse width modulation (PWM) at moderate to heavy load currents. At light load currents the converter can automatically enter Power Save Mode and operates then in PFM mode. During PWM operation the converter use a unique fast response voltage mode control scheme with input voltage feed-forward to achieve good line and load regulation allowing the use of small ceramic input and output capacitors. At the beginning of each clock cycle initiated by the clock signal, the High Side MOSFET switch is turned on. The current flows now from the input capacitor via the High Side MOSFET switch through the inductor to the output capacitor and load. During this phase, the current ramps up until the PWM comparator trips and the control logic will turn off the switch. The current limit comparator will also turn off the switch in case the current limit of the High Side MOSFET switch is exceeded. After a dead time preventing shoot through current, the Low Side MOSFET rectifier is turned on and the inductor current will ramp down. The current flows now from the inductor to the output capacitor and to the load. It returns back to the inductor through the Low Side MOSFET rectifier. The next cycle will be initiated by the clock signal again turning off the Low Side MOSFET rectifier and turning on the on the High Side MOSFET switch. POWER SAVE MODE The Power Save Mode is enabled with MODE Pin set to low level. If the load current decreases, the converter will enter Power Save Mode operation automatically. During Power Save Mode the converter skips switching and operates with reduced frequency in PFM mode with a minimum quiescent current to maintain high efficiency. The converter will position the output voltage typically +1% above the nominal output voltage. This voltage positioning feature minimizes voltage drops caused by a sudden load step. The transition from PWM mode to PFM mode occurs once the inductor current in the Low Side MOSFET switch becomes zero, which indicates discontinuous conduction mode. During the Power Save Mode the output voltage is monitored with a PFM comparator. As the output voltage falls below the PFM comparator threshold of VOUT nominal +1%, the device starts a PFM current pulse. The High Side MOSFET switch will turn on, and the inductor current ramps up. After the On-time expires, the switch is turned off and the Low Side MOSFET switch is turned on until the inductor current becomes zero. The converter effectively delivers a current to the output capacitor and the load. If the load is below the delivered current, the output voltage will rise. If the output voltage is equal or higher than the PFM comparator threshold, the device stops switching and enters a sleep mode with typical 15A current consumption. If the output voltage is still below the PFM comparator threshold, a sequence of further PFM current pulses are generated until the PFM comparator threshold is reached. The converter starts switching again once the output voltage drops below the PFM comparator threshold. With a fast single threshold comparator, the output voltage ripple during PFM mode operation can be kept small. The PFM Pulse is time controlled, which allows to modify the charge transferred to the output capacitor by the value of the inductor. The resulting PFM output voltage ripple and PFM frequency depend in first order on the size of the output capacitor and the inductor value. Increasing output capacitor values and inductor values will minimize the output ripple. The PFM frequency decreases with smaller inductor values and increases with larger values. The PFM mode is left and PWM mode entered in case the output current can not longer be supported in PFM mode. The Power Save Mode can be disabled through the MODE pin set to high. The converter will then operate in fixed frequency PWM mode. Dynamic Voltage Positioning This feature reduces the voltage under/overshoots at load steps from light to heavy load and vice versa. It is active in Power Save Mode and regulates the output voltage 1% higher than the nominal value. This provides more headroom for both the voltage drop at a load step, and the voltage increase at a load throw-off. (c) 2007-2011, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TPS62260 TPS62261 TPS62262 TPS62263 15 TPS62260, TPS62261 TPS62262, TPS62263 SLVS763D - JUNE 2007 - REVISED FEBRUARY 2011 www.ti.com Output voltage Voltage Positioning Vout +1% PFM Comparator threshold Light load PFM Mode Vout (PWM) moderate to heavy load PWM Mode Figure 34. Power Save Mode Operation with automatic Mode transition 100% Duty Cycle Low Dropout Operation The device starts to enter 100% duty cycle mode once the input voltage comes close to the nominal output voltage. In order to maintain the output voltage, the High Side MOSFET switch is turned on 100% for one or more cycles. With further decreasing VIN the High Side MOSFET switch is turned on completely. In this case the converter offers a low input-to-output voltage difference. This is particularly useful in battery-powered applications to achieve longest operation time by taking full advantage of the whole battery voltage range. The minimum input voltage to maintain regulation depends on the load current and output voltage, and can be calculated as: VINmin = VOmax + IOmax x (RDS(on)max + RL) With: IOmax = maximum output current plus inductor ripple current RDS(on)max = maximum P-channel switch RDSon. RL = DC resistance of the inductor VOmax = nominal output voltage plus maximum output voltage tolerance Undervoltage Lockout The undervoltage lockout circuit prevents the device from malfunctioning at low input voltages and from excessive discharge of the battery and disables the output stage of the converter. The undervoltage lockout threshold is typically 1.85V with falling VIN. MODE SELECTION The MODE pin allows mode selection between forced PWM mode and Power Save Mode. Connecting this pin to GND enables the Power Save Mode with automatic transition between PWM and PFM mode. Pulling the MODE pin high forces the converter to operate in fixed frequency PWM mode even at light load currents. This allows simple filtering of the switching frequency for noise sensitive applications. In this mode, the efficiency is lower compared to the power save mode during light loads. The condition of the MODE pin can be changed during operation and allows efficient power management by adjusting the operation mode of the converter to the specific system requirements. 16 Submit Documentation Feedback (c) 2007-2011, Texas Instruments Incorporated Product Folder Link(s): TPS62260 TPS62261 TPS62262 TPS62263 TPS62260, TPS62261 TPS62262, TPS62263 SLVS763D - JUNE 2007 - REVISED FEBRUARY 2011 www.ti.com ENABLE The device is enabled setting EN pin to high. During the start up time tStart Up the internal circuits are settled and the soft start circuit is activated. The EN input can be used to control power sequencing in a system with various DC/DC converters. The EN pin can be connected to the output of another converter, to drive the EN pin high and getting a sequencing of supply rails. With EN = GND, the device enters shutdown mode in which all internal circuits are disabled. In fixed output voltage versions, the internal resistor divider network is then disconnected from FB pin. SOFT START The TPS62260 has an internal soft start circuit that controls the ramp up of the output voltage. The output voltage ramps up from 5% to 95% of its nominal value within typical 250s. This limits the inrush current in the converter during ramp up and prevents possible input voltage drops when a battery or high impedance power source is used. The soft start circuit is enabled within the start up time tStart Up. SHORT-CIRCUIT PROTECTION The High Side and Low Side MOSFET switches are short-circuit protected with maximum switch current = ILIMF. The current in the switches is monitored by current limit comparators. Once the current in the High Side MOSFET switch exceeds the threshold of it's current limit comparator, it turns off and the Low Side MOSFET switch is activated to ramp down the current in the inductor and High Side MOSFET switch. The High Side MOSFET switch can only turn on again, once the current in the Low Side MOSFET switch has decreased below the threshold of its current limit comparator. THERMAL SHUTDOWN As soon as the junction temperature, TJ, exceeds 140C (typical) the device goes into thermal shutdown. In this mode, the High Side and Low Side MOSFETs are turned-off. The device continues its operation when the junction temperature falls below the thermal shutdown hysteresis. (c) 2007-2011, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TPS62260 TPS62261 TPS62262 TPS62263 17 TPS62260, TPS62261 TPS62262, TPS62263 SLVS763D - JUNE 2007 - REVISED FEBRUARY 2011 www.ti.com APPLICATION INFORMATION VIN CIN 4.7 mF VOUT 1.2 V Up to 600 mA L1 2.2 mH TPS62262DRV VIN = 2 V to 6 V SW COUT 10 mF EN FB GND MODE Figure 35. TPS62260 Fixed 1.2-V Output TPS62260DRV VIN CIN 4.7 mF L1 2.2 mH VOUT 1.2 V SW R1 360 kW EN GND C1 22 pF COUT 10 mF FB R2 360 kW MODE Figure 36. TPS62260DRV Adjustable 1.2-V Output TPS62260DRV VIN CIN 4.7 mF VOUT 1.5 V Up to 600 mA L1 2.2 mH VIN = 2 V to 6 V SW R1 540 k EN C1 22 pF COUT 10 mF FB GND MODE R2 360 k Figure 37. TPS62260 adjustable 1.5-V Output 18 Submit Documentation Feedback (c) 2007-2011, Texas Instruments Incorporated Product Folder Link(s): TPS62260 TPS62261 TPS62262 TPS62263 TPS62260, TPS62261 TPS62262, TPS62263 SLVS763D - JUNE 2007 - REVISED FEBRUARY 2011 www.ti.com VIN CIN 4.7 mF VOUT 1.8 V Up to 600 mA L1 2.2 mH TPS62261DRV VIN = 2 V to 6 V SW EN COUT 10 mF FB GND MODE Figure 38. TPS62261 Fixed 1.8-V Output OUTPUT VOLTAGE SETTING The output voltage can be calculated to: R V OUT + VREF 1) 1 R2 with an internal reference voltage VREF typical 0.6V. To minimize the current through the feedback divider network, R2 should be 180 k or 360 k. The sum of R1 and R2 should not exceed ~1M, to keep the network robust against noise. An external feed forward capacitor C1 is required for optimum load transient response. The value of C1 should be in the range between 22pF and 33pF. Route the FB line away from noise sources, such as the inductor or the SW line. OUTPUT FILTER DESIGN (INDUCTOR AND OUTPUT CAPACITOR) The TPS62260 is designed to operate with inductors in the range of 1.5H to 4.7H and with output capacitors in the range of 4.7F to 22F. The part is optimized for operation with a 2.2H inductor and 10F output capacitor. Larger or smaller inductor values can be used to optimize the performance of the device for specific operation conditions. For stable operation, the L and C values of the output filter may not fall below 1H effective inductance and 3.5F effective capacitance. Inductor Selection The inductor value has a direct effect on the ripple current. The selected inductor has to be rated for its dc resistance and saturation current. The inductor ripple current (IL) decreases with higher inductance and increases with higher VI or VO. The inductor selection has also impact on the output voltage ripple in PFM mode. Higher inductor values will lead to lower output voltage ripple and higher PFM frequency, lower inductor values will lead to a higher output voltage ripple but lower PFM frequency. Equation 1 calculates the maximum inductor current in PWM mode under static load conditions. The saturation current of the inductor should be rated higher than the maximum inductor current as calculated with Equation 2. This is recommended because during heavy load transient the inductor current will rise above the calculated value. V 1 * OUT V DI L + VOUT L I L max + I out max ) IN f DI L (1) 2 (2) (c) 2007-2011, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TPS62260 TPS62261 TPS62262 TPS62263 19 TPS62260, TPS62261 TPS62262, TPS62263 SLVS763D - JUNE 2007 - REVISED FEBRUARY 2011 www.ti.com With: f = Switching Frequency (2.25MHz typical) L = Inductor Value IL = Peak to Peak inductor ripple current ILmax = Maximum Inductor current A more conservative approach is to select the inductor current rating just for the switch current limit ILIMF of the converter. Accepting larger values of ripple current allows the use of lower inductance values, but results in higher output voltage ripple, greater core losses, and lower output current capability. The total losses of the coil have a strong impact on the efficiency of the DC/DC conversion and consist of both the losses in the dc resistance (R(DC)) and the following frequency-dependent components: * The losses in the core material (magnetic hysteresis loss, especially at high switching frequencies) * Additional losses in the conductor from the skin effect (current displacement at high frequencies) * Magnetic field losses of the neighboring windings (proximity effect) * Radiation losses Table 2. List of Inductors DIMENSIONS [mm3] Inductance H 2.5x2.0x1.0max 2.5x2.0x1.2max INDUCTOR TYPE SUPPLIER 2.0 MIPS2520D2R2 FDK 2.0 MIPSA2520D2R2 FDK 2.5x2.0x1.0max 2.2 KSLI-252010AG2R2 Htachi Metals 2.5x2.0x1.2max 2.2 LQM2HPN2R2MJ0L Murata 3x3x1.5max 2.2 LPS3015 2R2 Coilcraft Output Capacitor Selection The advanced fast-response voltage mode control scheme of the TPS62260 allows the use of tiny ceramic capacitors. Ceramic capacitors with low ESR values have the lowest output voltage ripple and are recommended. The output capacitor requires either an X7R or X5R dielectric. Y5V and Z5U dielectric capacitors, aside from their wide variation in capacitance over temperature, become resistive at high frequencies. At nominal load current, the device operates in PWM mode and the RMS ripple current is calculated as: V 1 * OUT V I RMSC OUT + VOUT L IN f 1 2 3 (3) At nominal load current, the device operates in PWM mode and the overall output voltage ripple is the sum of the voltage spike caused by the output capacitor ESR plus the voltage ripple caused by charging and discharging the output capacitor: V 1 * OUT V DV OUT + VOUT L IN f 8 1 Cout f ) ESR (4) At light load currents, the converter operates in Power Save Mode and the output voltage ripple is dependent on the output capacitor and inductor value. Larger output capacitor and inductor values minimize the voltage ripple in PFM mode and tighten DC output accuracy in PFM mode. 20 Submit Documentation Feedback (c) 2007-2011, Texas Instruments Incorporated Product Folder Link(s): TPS62260 TPS62261 TPS62262 TPS62263 TPS62260, TPS62261 TPS62262, TPS62263 SLVS763D - JUNE 2007 - REVISED FEBRUARY 2011 www.ti.com Input Capacitor Selection An input capacitor is required for best input voltage filtering, and minimizing the interference with other circuits caused by high input voltage spikes. For most applications, a 4.7F to 10F ceramic capacitor is recommended. Because ceramic capacitor loses up to 80% of its initial capacitance at 5 V, it is recommended that 10F input capacitors be used for input voltages > 4.5V. The input capacitor can be increased without any limit for better input voltage filtering. Take care when using only small ceramic input capacitors. When a ceramic capacitor is used at the input and the power is being supplied through long wires, such as from a wall adapter, a load step at the output or VIN step on the input can induce ringing at the VIN pin. This ringing can couple to the output and be mistaken as loop instability or could even damage the part by exceeding the maximum ratings. Table 3. List of Capacitors CAPACITANCE TYPE SIZE 4.7F GRM188R60J475K 0603 1.6x0.8x0.8mm3 Murata 3 Murata 10F GRM188R60J106M69D SUPPLIER 0603 1.6x0.8x0.8mm LAYOUT CONSIDERATIONS Figure 39. Suggested Layout for Fixed Output Voltage Options (c) 2007-2011, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Link(s): TPS62260 TPS62261 TPS62262 TPS62263 21 TPS62260, TPS62261 TPS62262, TPS62263 SLVS763D - JUNE 2007 - REVISED FEBRUARY 2011 www.ti.com VOUT R2 GND C1 R1 COUT CIN VIN L G N D U Figure 40. Suggested Layout for Adjustable Output Voltage Version As for all switching power supplies, the layout is an important step in the design. Proper function of the device demands careful attention to PCB layout. Care must be taken in board layout to get the specified performance. If the layout is not carefully done, the regulator could show poor line and/or load regulation, stability issues as well as EMI problems. It is critical to provide a low inductance, impedance ground path. Therefore, use wide and short traces for the main current paths. The input capacitor should be placed as close as possible to the IC pins as well as the inductor and output capacitor. Connect the GND Pin of the device to the PowerPADTM land of the PCB and use this pad as a star point. Use a common Power GND node and a different node for the Signal GND to minimize the effects of ground noise. Connect these ground nodes together to the PowerPAD land (star point) underneath the IC. Keep the common path to the GND PIN, which returns the small signal components and the high current of the output capacitors as short as possible to avoid ground noise. The FB line should be connected right to the output capacitor and routed away from noisy components and traces (e.g., SW line). 22 Submit Documentation Feedback (c) 2007-2011, Texas Instruments Incorporated Product Folder Link(s): TPS62260 TPS62261 TPS62262 TPS62263 PACKAGE OPTION ADDENDUM www.ti.com 18-Apr-2011 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) TPS62260DDCR ACTIVE SOT DDC 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS62260DDCRG4 ACTIVE SOT DDC 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS62260DDCT ACTIVE SOT DDC 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS62260DDCTG4 ACTIVE SOT DDC 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS62260DRVR ACTIVE SON DRV 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS62260DRVRG4 ACTIVE SON DRV 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS62260DRVT ACTIVE SON DRV 6 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS62260DRVTG4 ACTIVE SON DRV 6 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TPS62261DRVR ACTIVE SON DRV 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS62261DRVRG4 ACTIVE SON DRV 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS62261DRVT ACTIVE SON DRV 6 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS62261DRVTG4 ACTIVE SON DRV 6 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS62262DDCR ACTIVE SOT DDC 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS62262DDCT ACTIVE SOT DDC 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS62262DRVR ACTIVE SON DRV 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS62262DRVRG4 ACTIVE SON DRV 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS62262DRVT ACTIVE SON DRV 6 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Addendum-Page 1 Samples (Requires Login) PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 18-Apr-2011 Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp TPS62262DRVTG4 ACTIVE SON DRV 6 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS62263DRVR ACTIVE SON DRV 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS62263DRVRG4 ACTIVE SON DRV 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS62263DRVT ACTIVE SON DRV 6 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS62263DRVTG4 ACTIVE SON DRV 6 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM (3) Samples (Requires Login) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF TPS62260, TPS62261, TPS62262, TPS62263 : Addendum-Page 2 PACKAGE OPTION ADDENDUM www.ti.com 18-Apr-2011 * Automotive: TPS62260-Q1, TPS62261-Q1, TPS62262-Q1, TPS62263-Q1 NOTE: Qualified Version Definitions: * Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects Addendum-Page 3 PACKAGE MATERIALS INFORMATION www.ti.com 2-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device TPS62260DDCR Package Package Pins Type Drawing SOT DDC 5 SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 3000 179.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 TPS62260DDCT SOT DDC 5 250 179.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 TPS62260DRVR SON DRV 6 3000 179.0 8.4 2.2 2.2 1.2 4.0 8.0 Q2 TPS62260DRVT SON DRV 6 250 179.0 8.4 2.2 2.2 1.2 4.0 8.0 Q2 TPS62261DRVR SON DRV 6 3000 179.0 8.4 2.2 2.2 1.2 4.0 8.0 Q2 TPS62261DRVT SON DRV 6 250 179.0 8.4 2.2 2.2 1.2 4.0 8.0 Q2 TPS62262DDCR SOT DDC 5 3000 179.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 TPS62262DDCT SOT DDC 5 250 179.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 TPS62262DRVR SON DRV 6 3000 179.0 8.4 2.2 2.2 1.2 4.0 8.0 Q2 TPS62262DRVT SON DRV 6 250 179.0 8.4 2.2 2.2 1.2 4.0 8.0 Q2 TPS62263DRVR SON DRV 6 3000 179.0 8.4 2.2 2.2 1.2 4.0 8.0 Q2 TPS62263DRVT SON DRV 6 250 179.0 8.4 2.2 2.2 1.2 4.0 8.0 Q2 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 2-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TPS62260DDCR SOT DDC 5 3000 203.0 203.0 35.0 TPS62260DDCT SOT DDC 5 250 203.0 203.0 35.0 TPS62260DRVR SON DRV 6 3000 203.0 203.0 35.0 TPS62260DRVT SON DRV 6 250 203.0 203.0 35.0 TPS62261DRVR SON DRV 6 3000 203.0 203.0 35.0 TPS62261DRVT SON DRV 6 250 203.0 203.0 35.0 TPS62262DDCR SOT DDC 5 3000 203.0 203.0 35.0 TPS62262DDCT SOT DDC 5 250 203.0 203.0 35.0 TPS62262DRVR SON DRV 6 3000 203.0 203.0 35.0 TPS62262DRVT SON DRV 6 250 203.0 203.0 35.0 TPS62263DRVR SON DRV 6 3000 203.0 203.0 35.0 TPS62263DRVT SON DRV 6 250 203.0 203.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE ("CRITICAL APPLICATIONS"). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER'S RISK. In order to minimize risks associated with the customer's applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TI's publication of information regarding any third party's products or services does not constitute TI's approval, warranty or endorsement thereof. Copyright (c) 1998, Texas Instruments Incorporated