USER'S MANUAL ISL2828xEVAL1Z AN1344 Rev 0.00 August 2, 2007 Evaluation Board User Guide rate-of-rise to less than 1V/s. Two additional capacitors, C10 and C18, are connected close to the part to filter out high frequency noise. Anti-reverse diodes D1, D2 and zener diode D3 protect the circuit in the case of accidental polarity reversal. 1 R40 R40 Reference Documents C10 C10 * ISL28286 Data Sheet, FN6312 J2 C12 C12 R46 R46 + 4.7UF 4.7F D2 D2 00 1 1 A A 2 NC NC RF + IN(A, B)IN- IN- GND C18 C18 0.1UF 0.1F C16 C16 + DNP VP VP 0 V+ IN+ + VOUT(x) VVM 10k RREF(A,B)+ VREF 0 1/2 ISL2828x - 10k 0 R49 CC 3 3 100k 10k VREF D3 The schematic of each of the 2 op amps with the components supplied is shown in Figure 2. The circuit implements a differential input amp with a closed loop gain of 10. The circuit can operate from a single 2.4VDC to +5VDC supply, or from dual supplies from 1.2VDC to 2.5VDC. The VREF pin can be connected to ground to establish a ground referenced input for split supply operation, or can be externally set to any reference level for single supply operation. External power connections are made through the V+, Vand Ground connections on the evaluation board. For single supply operation, the V- and Ground pins are tied together to the power supply negative terminal. For split supplies V+ and V- terminals connect to their respective power supply terminals. De-coupling capacitors C12, C17, connect to ground through R1, R46, 0 resistors. Resistors R40 and R49 are 0 but can be changed by the user to provide additional power supply filtering, or to reduce the voltage VCM 1 Amplifier Configuration (Figure 2) Power Supplies (Figure 1) IN(A, B)+ + FIGURE 1. POWER SUPPLY CIRCUIT The ISL2828xEVAL1Z is designed to enable the IC to operate from a single supply (+2.4VDC to +5VDC), or from split supplies (1.2VDC to 2.5V). The board is configured for 2 independent op amps connected for differential input with a closed loop gain of 10. A single external reference voltage (VREF) pin and provisions for a user-selectable voltage divider (filter is included). IN+ C17 C17 V+ V+ 4.7UF D1 4.7F D1 MMBZ52xxB Evaluation Board Key Features RIN+ 2 D3 0 VM RIN- R1 R1 00 0.1F * ISL28288 Data Sheet, FN6339 J1 1 J3 V- R49 The ISL2828x amplifiers feature low noise, low distortion, and rail-to-rail output drive capability. They are designed to operate with single and dual supplies from +5VDC (2.5VDC) down to +2.4VDC (1.2VDC). 1 The ISL2828xEVAL1Z evaluation board is a design platform containing all the circuitry needed to characterize critical performance parameters of the ISL28286 and ISL28288 dual operational amplifiers, using a variety of user defined test circuits. 100k 0 TO OTHER CHANNEL 10k FIGURE 2. BASIC AMPLIFIER CONFIGURATION AN1344 Rev 0.00 August 2, 2007 Page 1 of 5 ISL2828xEVAL1Z User-Selectable Options (Figures 3 to 5) Component pads are included to enable a variety of user-selectable circuits to be added to the amplifier inputs, the VREF input, outputs and the amplifier feedback loops. The outputs (Figure 3) have additional resistor and capacitor placements for loading. A voltage divider and filter option (Figure 4) can be added to establish a power supply-tracking common mode reference at the VREF input. The inverting and non-inverting inputs have additional resistor placements for adding input attenuation, or to establish input DC offsets through the VREF pin. ROUT A R55 R55 0 DNP R44 R39 IN+ A DNP ENA 6 3 R57 V- 7 ENB 11 IN+ B R37 DNP RFA1, R45, 100k R36 DNP INA+ 5 J15 OUT A 12 5 2 34 DNP R57 10K IN- A 2 OUT 10K R53 OPEN 1 R51 DNP R51 DNP 1 R53 C19 OPEN 2 In the standard configuration (Figure 5), R41 and R45 are RF feedback resistors for the two independent amplifiers, set for AV = 10. Resistors R47 and R48 connect the DUT output to the output circuit (Figure 3). The additional unpopulated components, R34 to R39, R42 to R44, C10, C11, C13 to C15 and C18 allow the user to configure the board for a variety of other applications such as cascaded gain stages, active feedback loops, etc. C13 CFA DNP - 4 INA+ 3 OUTA R42 15 V+ RGDIFF DNP +14 OUTB INB+ 12 R38 DNP 13 INB- R47 RSA C14 DNP CLA C15 CLB DNP OUT A OUT B RSB R48, 0 R43, DNP IN- B FIGURE 3. 1/2 OUTPUT STAGE RFB1, R41,100k C11 CFB DNP 1 OPEN 2 100k RREF 1 RREFAR31 R31 C9 C9 1 2 + 4.7F DNP 3 R2 R2 RINA2RINA2- DNP R8 R8 DNP DNP 1 R17 R17 J6 4 INA2- RINAR21 R21 10k C6 C6 2 1 0 00 R32 R32 2 OPEN OPEN R33 R33 1 FIGURE 5. OPTIONAL COMPONENTS VREF 10k C2 C2 2 DNP DNP 3 1 5 R25 R25 J5 4 INA1- J4 J4 REF1 REF1 RINA1R13 R13 + C3 C3 2 1 OPEN OPEN R9 R9 1 OPEN DNP DNP RINA2+ RINA2+ R18 DNP 100k 1 ININ+ R26 100k RGA+ 1 R3 R3 2 R18 2 RINA+ R22 R22 10k C7 210K C7 00 DNP 3 1 4 INA2+ J8 2 RREFA+ R30 R30 R26 3 1 4 INA1+ RINA1+ R14 R14 1 2 DNP J7 J7 FIGURE 4. 1/2 INPUT STAGE ISL2828xEVAL1Z Components Parts List DEVICE NUMBER C9, C12, C17 DESCRIPTION CAP-TANTALUM, SMD, D, 4.7F, 50V, 10%, LOW ESR, ROHS COMMENTS Power supply decoupling C10,C18 CAP, SMD, 0603, 0.1F, 25V, 10%, X7R, ROHS Power supply decoupling C6-C25 CAP, SMD, 0603, DNP-PLACE HOLDER, ROHS User selectable capacitors not populated DIODE-RECTIFIER, SMD, SOD-123, 2P, 40V, 0.5A, ROHS Reverse power protection DIODE-ZENER, SMD, SOD-123, 2P, 5.1V, 350mV, ROHS Reverse power protection D1,D2 D3 U1 (ISL28286EVAL1Z) ISL28286FAZ, IC-RAIL-TO-RAIL PRECISION OP AMP, 16P, QSOP, ROHS U1 (ISL28288EVAL1Z) ISL28288FAZ, IC-RAIL-TO-RAIL PRECISION OP AMP, 16P, QSOP, ROHS RESISTOR,SMD, 0603, 0.1%, MF, DNP-PLACE HOLDER User selectable resistors - not populated RES, SMD, 0603, 0W, 1/10W, TF, ROHS 0 user selectable resistors R6, R7, R20-R23, R33, R53, R54 RES, SMD, 0603, 10k, 1/10W, 1%, TF, ROHS RG gain resistors R28, R30, R41, R45 RES, SMD, 0603, 100k, 1/10W, 1%, TF, ROHS RF gain resistors R2-R5, R8-R10, R12, R16-R19, R24-R27, R29, R31, R34-R39, R42-R44, R50-R52, R57, R58 R1, R11, R13-R15, R24, R25, R32, R40, R46-R49, R55, R56 AN1344 Rev 0.00 August 2, 2007 Page 2 of 5 ISL2828xEVAL1Z ISL2828xEVAL1Z Top View AN1344 Rev 0.00 August 2, 2007 Page 3 of 5 AN1344 Rev 0.00 August 2, 2007 INB2- INB1- INB2+ INB1+ ENB ENA INA2+ INA1+ INA2- INA1- (C6) DNP DNP (R5) DNP (R12) RINB2- DNP (C1) (C8) DNP (C5) (10 k) (R20) RINB- (R24) DNP RGB- RREFB-(R29) DNP RGB+ (R27) DNP RINB+ (R23) (10 k) (R16) DNP RINB1- (R11) (0) (R4) DNP (R10) RINB2+ DNP V+ RGA+ (R26) DNP RREFB+ (R28) (100 k) (R19) DNP RINB1+ (R15) (0) (C4) DNP (C7) (R18) DNP (R7) (10 k) (R6) (10 k) (R3) DNP DNP RINA+ (R22) (10 k) RINA2+ DNP (R9) RREFA+(R30) (100 k) (C3) DNP RGA(R25) DNP RREFA- (R31) DNP RINA- (R21) (10 k) (R17) DNP RINA1+ (R14) (0) (R2) DNP (R8) RINA2- DNP (C2) DNP RINA1- (R13) (0) (C10) V- (R32) RREF (R37) DNP 4 3 2 (0) 4.7uF (C9) (10 k) (R33) (R38) DNP INB+ 5 ENB V- ENA INA+ 1 (R36) DNP VREF (R35) DNP (R34) DNP (R39) DNP - - (0) 4.7uF (R43) DNP (C18) V- (0) (R40) (D2) GND 5.1V (C16) (D3) DNP + CFB DNP (C11) V+ 4.7uF (C17) (C15) CLB DNP DNP (C14) CLA V+ (0) (R49) (D1) (R42) RGDIFF DNP RFB1 (R41) (100 k) V- OUTB V+ 6 INB- 7 8 9 OUTA 10 INA- (R46) (C12) + + CFA DNP (C13) RFA1 (R45) (100 k) (R44) DNP DNP (0) (R1) RSB (R48) (0) ROUTAB (R47) (0) RSA (C20) DNP (R52) DNP (R50) DNP (C19) DNP (R51) DNP (R54) (10 k) (R56) (0) ROUTB (R53) (10 k) (R55) (0) ROUTA (R58) DNP (R57) DNP OUTB OUTA ISL2828xEVAL1Z ISL2828xEVAL1Z Schematic Diagram Page 4 of 5 Notice 1. Descriptions of circuits, software and other related information in this document are provided only to illustrate the operation of semiconductor products and application examples. You are fully responsible for the incorporation or any other use of the circuits, software, and information in the design of your product or system. Renesas Electronics disclaims any and all liability for any losses and damages incurred by you or third parties arising from the use of these circuits, software, or information. 2. Renesas Electronics hereby expressly disclaims any warranties against and liability for infringement or any other claims involving patents, copyrights, or other intellectual property rights of third parties, by or arising from the use of Renesas Electronics products or technical information described in this document, including but not limited to, the product data, drawings, charts, programs, algorithms, and application examples. 3. No license, express, implied or otherwise, is granted hereby under any patents, copyrights or other intellectual property rights of Renesas Electronics or others. 4. You shall not alter, modify, copy, or reverse engineer any Renesas Electronics product, whether in whole or in part. Renesas Electronics disclaims any and all liability for any losses or damages incurred by 5. Renesas Electronics products are classified according to the following two quality grades: "Standard" and "High Quality". The intended applications for each Renesas Electronics product depends on the you or third parties arising from such alteration, modification, copying or reverse engineering. product's quality grade, as indicated below. "Standard": Computers; office equipment; communications equipment; test and measurement equipment; audio and visual equipment; home electronic appliances; machine tools; personal electronic equipment; industrial robots; etc. "High Quality": Transportation equipment (automobiles, trains, ships, etc.); traffic control (traffic lights); large-scale communication equipment; key financial terminal systems; safety control equipment; etc. Unless expressly designated as a high reliability product or a product for harsh environments in a Renesas Electronics data sheet or other Renesas Electronics document, Renesas Electronics products are not intended or authorized for use in products or systems that may pose a direct threat to human life or bodily injury (artificial life support devices or systems; surgical implantations; etc.), or may cause serious property damage (space system; undersea repeaters; nuclear power control systems; aircraft control systems; key plant systems; military equipment; etc.). Renesas Electronics disclaims any and all liability for any damages or losses incurred by you or any third parties arising from the use of any Renesas Electronics product that is inconsistent with any Renesas Electronics data sheet, user's manual or other Renesas Electronics document. 6. When using Renesas Electronics products, refer to the latest product information (data sheets, user's manuals, application notes, "General Notes for Handling and Using Semiconductor Devices" in the reliability handbook, etc.), and ensure that usage conditions are within the ranges specified by Renesas Electronics with respect to maximum ratings, operating power supply voltage range, heat dissipation characteristics, installation, etc. Renesas Electronics disclaims any and all liability for any malfunctions, failure or accident arising out of the use of Renesas Electronics products outside of such specified ranges. 7. Although Renesas Electronics endeavors to improve the quality and reliability of Renesas Electronics products, semiconductor products have specific characteristics, such as the occurrence of failure at a certain rate and malfunctions under certain use conditions. Unless designated as a high reliability product or a product for harsh environments in a Renesas Electronics data sheet or other Renesas Electronics document, Renesas Electronics products are not subject to radiation resistance design. You are responsible for implementing safety measures to guard against the possibility of bodily injury, injury or damage caused by fire, and/or danger to the public in the event of a failure or malfunction of Renesas Electronics products, such as safety design for hardware and software, including but not limited to redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other appropriate measures. Because the evaluation of microcomputer software alone is very difficult and impractical, you are responsible for evaluating the safety of the final products or systems manufactured by you. 8. Please contact a Renesas Electronics sales office for details as to environmental matters such as the environmental compatibility of each Renesas Electronics product. You are responsible for carefully and sufficiently investigating applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive, and using Renesas Electronics products in compliance with all these applicable laws and regulations. Renesas Electronics disclaims any and all liability for damages or losses occurring as a result of your noncompliance with applicable laws and regulations. 9. Renesas Electronics products and technologies shall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable domestic or foreign laws or regulations. You shall comply with any applicable export control laws and regulations promulgated and administered by the governments of any countries asserting jurisdiction over the parties or transactions. 10. It is the responsibility of the buyer or distributor of Renesas Electronics products, or any other party who distributes, disposes of, or otherwise sells or transfers the product to a third party, to notify such third party in advance of the contents and conditions set forth in this document. 11. This document shall not be reprinted, reproduced or duplicated in any form, in whole or in part, without prior written consent of Renesas Electronics. 12. Please contact a Renesas Electronics sales office if you have any questions regarding the information contained in this document or Renesas Electronics products. (Note 1) "Renesas Electronics" as used in this document means Renesas Electronics Corporation and also includes its directly or indirectly controlled subsidiaries. (Note 2) "Renesas Electronics product(s)" means any product developed or manufactured by or for Renesas Electronics. (Rev.4.0-1 November 2017) http://www.renesas.com SALES OFFICES Refer to "http://www.renesas.com/" for the latest and detailed information. Renesas Electronics America Inc. 1001 Murphy Ranch Road, Milpitas, CA 95035, U.S.A. Tel: +1-408-432-8888, Fax: +1-408-434-5351 Renesas Electronics Canada Limited 9251 Yonge Street, Suite 8309 Richmond Hill, Ontario Canada L4C 9T3 Tel: +1-905-237-2004 Renesas Electronics Europe Limited Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K Tel: +44-1628-651-700, Fax: +44-1628-651-804 Renesas Electronics Europe GmbH Arcadiastrasse 10, 40472 Dusseldorf, Germany Tel: +49-211-6503-0, Fax: +49-211-6503-1327 Renesas Electronics (China) Co., Ltd. Room 1709 Quantum Plaza, No.27 ZhichunLu, Haidian District, Beijing, 100191 P. R. China Tel: +86-10-8235-1155, Fax: +86-10-8235-7679 Renesas Electronics (Shanghai) Co., Ltd. Unit 301, Tower A, Central Towers, 555 Langao Road, Putuo District, Shanghai, 200333 P. R. China Tel: +86-21-2226-0888, Fax: +86-21-2226-0999 Renesas Electronics Hong Kong Limited Unit 1601-1611, 16/F., Tower 2, Grand Century Place, 193 Prince Edward Road West, Mongkok, Kowloon, Hong Kong Tel: +852-2265-6688, Fax: +852 2886-9022 Renesas Electronics Taiwan Co., Ltd. 13F, No. 363, Fu Shing North Road, Taipei 10543, Taiwan Tel: +886-2-8175-9600, Fax: +886 2-8175-9670 Renesas Electronics Singapore Pte. Ltd. 80 Bendemeer Road, Unit #06-02 Hyflux Innovation Centre, Singapore 339949 Tel: +65-6213-0200, Fax: +65-6213-0300 Renesas Electronics Malaysia Sdn.Bhd. Unit 1207, Block B, Menara Amcorp, Amcorp Trade Centre, No. 18, Jln Persiaran Barat, 46050 Petaling Jaya, Selangor Darul Ehsan, Malaysia Tel: +60-3-7955-9390, Fax: +60-3-7955-9510 Renesas Electronics India Pvt. Ltd. No.777C, 100 Feet Road, HAL 2nd Stage, Indiranagar, Bangalore 560 038, India Tel: +91-80-67208700, Fax: +91-80-67208777 Renesas Electronics Korea Co., Ltd. 17F, KAMCO Yangjae Tower, 262, Gangnam-daero, Gangnam-gu, Seoul, 06265 Korea Tel: +82-2-558-3737, Fax: +82-2-558-5338 (c) 2018 Renesas Electronics Corporation. All rights reserved. Colophon 7.0