LM9036 LM9036 Ultra-Low Quiescent Current Voltage Regulator Literature Number: SNVS140D LM9036 Ultra-Low Quiescent Current Voltage Regulator General Description Features The LM9036 ultra-low quiescent current regulator features low dropout voltage and low current in the standby mode. With less than 25A Ground Pin current at a 0.1mA load, the LM9036 is ideally suited for automotive and other battery operated systems. The LM9036 retains all of the features that are common to low dropout regulators including a low dropout PNP pass device, short circuit protection, reverse battery protection, and thermal shutdown. The LM9036 has a 40V maximum operating voltage limit, a -40C to +125C operating temperature range, and 5% output voltage tolerance over the entire output current, input voltage, and temperature range. Ultra low Ground Pin current (IGND 25A for IOUT = 0.1mA) Fixed 5V, 3.3V, 50mA output Output tolerance 5% over line, load, and temperature Dropout voltage typically 200mV @ IOUT = 50mA -45V reverse transient protection Internal short circuit current limit Internal thermal shutdown protection 40V operating voltage limit Typical Application 20001101 * Required if regulator is located more than 2 from power supply filter capacitor. ** Required for stability. Must be rated over intended operating temperature range. Effective series resistance (ESR) is critical, see Electrical Characteristics. Locate capacitor as close as possible to the regulator output and ground pins. Capacitance may be increased without bound. (c) 2008 National Semiconductor Corporation 200011 www.national.com LM9036 Ultra-Low Quiescent Current Voltage Regulator July 10, 2008 Connection Diagrams TO-252 20001125 Top View Order Number LM9036DT-5.0, LM9036DTX-5.0, LM9036DT-3.3, LM9036DTX-3.3 See NS Package Number TD03B 20001127 20001128 Top View LM9036MM-3.3, , LM9036MMX-3.3, LM9036MM-5.0, LM9036MMX-5.0 See NS Package Number MUA08A Top View LM9036M-3.3, LM9036MX-3.3, LM9036M-5.0, LM9036MX-5.0 See NS Package Number M08A Ordering Information Output Voltage 3.3V 5.0V www.national.com Order Package Type Package Drawing Transport Media LM9036M-3.3 8-Lead SOIC M08A Rail LM9036MX-3.3 8-Lead SOIC M08A Tape/Reel LM9036DT-3.3 TO-252 TD03B Rail LM9036DTX-3.3 TO-252 TD03B Tape/Reel LM9036MM-3.3 8-Lead Mini SOIC MUA08A Rail LM9036MMX-3.3 8-Lead Mini SOIC MUA08A Tape/Reel LM9036M-5.0 8-Lead SOIC M08A Rail LM9036MX-5.0 8-Lead SOIC M08A Tape/Reel LM9036DT-5.0 TO-252 TD03B Rail LM9036DTX-5.0 TO-252 TD03B Tape/Reel LM9036MM-5.0 8-Lead Mini SOIC MUA08A Rail LM9036MMX-5.0 8-Lead Mini SOIC MUA08A Tape/Reel 2 Lead Temperature (Soldering, 10 sec.) Absolute Maximum Ratings (Note 1) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Input Voltage (Survival) ESD Susceptibility (Note 2) Power Dissipation (Note 3) Junction Temperature (TJmax) Storage Temperature Range 260C Operating Ratings +55V, -45V 1.9kV Internally limited 150C -65C to +150C Operating Temperature Range Maximum Input Voltage (Operational) -40C to +125C 40V 140C/W SO-8 (M08A) JA (Note 7) TO-252 (TD03B) JA (Note 7) 125C/W TO-252 (TD03B) JA (Note 8) 50C/W TO-252 (TD03B) JC (Note 7) 11C/W MSO-8 (MUA08A) JA (Note 7) 200C/W Electrical Characteristics - LM9036-5.0 VIN = 14V, IOUT = 10 mA, TJ = 25C, unless otherwise specified. Boldface limits apply over entire operating temperature range Min (Note 5) Typical (Note 4) Max (Note 5) 4.80 5.00 5.20 4.75 5.00 5.25 IOUT = 0.1mA, 8V VIN 24V 20 25 IOUT = 1mA, 8V VIN 24V 50 100 IOUT = 10mA, 8V VIN 24V 0.3 0.5 IOUT = 50mA, 8V VIN 24V 2.0 2.5 Line Regulation ( VOUT) 6V VIN 40V, IOUT = 1mA 10 30 mV Load Regulation ( VOUT) 0.1mA IOUT 5mA 10 30 mV 5mA IOUT 50mA 10 30 mV IOUT = 0.1mA 0.05 0.10 V IOUT = 50mA 0.20 0.40 V 250 mA Parameter Output Voltage (VOUT) Conditions 5.5V VIN 26V, 0.1mA IOUT 50mA (Note 6) Quiescent Current (IGND) Dropout Voltage ( VOUT) Units V A mA Short Circuit Current (ISC) VOUT = 0V 65 120 Ripple Rejection (PSRR) Vripple = 1Vrms, Fripple = 120Hz -40 -60 dB Output Bypass Capacitance (COUT) 0.3 ESR 8 10 22 F 0.1mA IOUT 50mA 3 www.national.com Electrical Characteristics - LM9036-3.3 VIN = 14V, IOUT = 10 mA, TJ = 25C, unless otherwise specified. Boldface limits apply over entire operating temperature range Min (Note 5) Typical (Note 4) Max (Note 5) 3.168 3.30 3.432 3.135 3.30 3.465 IOUT = 0.1mA, 8V VIN 24V 20 25 IOUT = 1mA, 8V VIN 24V 50 100 IOUT = 10mA, 8V VIN 24V 0.3 0.5 IOUT = 50mA, 8V VIN 24V 2.0 2.5 Line Regulation ( VOUT) 6V VIN 40V, IOUT = 1mA 10 30 mV Load Regulation ( VOUT) 0.1mA IOUT 5mA 10 30 mV 5mA IOUT 50mA 10 30 mV 0.05 0.10 V Parameter Output Voltage (VOUT) Conditions 5.5V VIN 26V, 0.1mA IOUT 50mA (Note 6) Quiescent Current (IGND) Dropout Voltage ( VOUT) IOUT = 0.1mA IOUT = 50mA Units V A mA 0.20 0.40 V Short Circuit Current (ISC) VOUT = 0V 65 120 250 mA Ripple Rejection (PSRR) Vripple = 1Vrms, Fripple = 120Hz -40 -60 dB Output Bypass Capacitance (COUT) 0.3 ESR 8 22 33 F 0.1mA IOUT 50mA Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. DC and AC electrical specifications do not apply when operating the device beyond its specified operating ratings. Note 2: Human body model, 100pF discharge through a 1.5k resistor. Note 3: The maximum power dissipation is a function of TJmax, JA, and TA. The maximum allowable power dissipation at any ambient temperature is PD = (TJmax - TA)/JA. If this dissipation is exceeded, the die temperature will rise above 150C and the LM9036 will go into thermal shutdown. Note 4: Typicals are at 25C (unless otherwise specified) and represent the most likely parametric norm. Note 5: Tested limits are guaranteed to National's AOQL (Average Outgoing Quality Level) and 100% tested. Note 6: To ensure constant junction temperature, pulse testing is used. Note 7: Worst case (Free Air) per EIA / JESD51-3. Note 8: Typical JA with 1 square inch of 2oz copper pad area directly under the ground tab. www.national.com 4 Typical Performance Characteristics Dropout Voltage Quiescent Current 20001108 20001111 Quiescent Current Quiescent Current 20001113 20001114 Peak Output Current 20001117 5 www.national.com Using the JA for a LM9036DT mounted on a circuit board as defined at (Note 8), and using the formula for maximum allowable dissipation given in (Note 3) for an ambient temperature (TA) of +85C, we find that PDMAX = 1.3W. Including the small contribution of the quiescent current IQ to the total power dissipation, the maximum input voltage (while still delivering 50mA output current) is 29.5V. The LM9036DT will go into thermal shutdown when attempting to deliver the full output current of 50mA, with an ambient temperature of +85C, and the input voltage is greater than 29.5V. Similarly, with an ambient temperature of 25C the PDMAX = 2.5W, and the LM9036DT can deliver the full output current of 50mA with an input voltage of up to 40V. While the LM9036 maintains regulation to 55V, it will not withstand a short circuit above 40V because of safe operating area limitations in the internal PNP pass device. Above 55V the LM9036 will break down with catastrophic effects on the regulator and possibly the load as well. Do not use this device in a design where the input operating voltage may exceed 40V, or where transients are likely to exceed 55V. Applications Information Unlike other PNP low dropout regulators, the LM9036 remains fully operational to 40V. Owing to power dissipation characteristics of the package, full output current cannot be guaranteed for all combinations of ambient temperature and input voltage. The junction to ambient thermal resistance JA rating has two distinct components: the junction to case thermal resistance rating JC; and the case to ambient thermal resistance rating CA. The relationship is defined as: JA = JC + CA. On the TO-252 package the ground tab is thermally connected to the backside of the die. Adding 1 square inch of 2 oz. copper pad area directly under the ground tab will improve the JA rating to approximately 50C/W. While the LM9036 has an internally set thermal shutdown point of typically 150C, this is intended as a safety feature only. Continuous operation near the thermal shutdown temperature should be avoided as it may have a negative affect on the life of the device. www.national.com 6 Physical Dimensions inches (millimeters) unless otherwise noted TO-252 Package (DT) NS Package Number TD03B 8 Lead Small Outline Molded Package (M) NS Package Number M08A 7 www.national.com 8 Lead Mini SOIC (MM) NS Package Number MUA08A www.national.com 8 Notes 9 www.national.com LM9036 Ultra-Low Quiescent Current Voltage Regulator Notes For more National Semiconductor product information and proven design tools, visit the following Web sites at: Products Design Support Amplifiers www.national.com/amplifiers WEBENCH www.national.com/webench Audio www.national.com/audio Analog University www.national.com/AU Clock Conditioners www.national.com/timing App Notes www.national.com/appnotes Data Converters www.national.com/adc Distributors www.national.com/contacts Displays www.national.com/displays Green Compliance www.national.com/quality/green Ethernet www.national.com/ethernet Packaging www.national.com/packaging Interface www.national.com/interface Quality and Reliability www.national.com/quality LVDS www.national.com/lvds Reference Designs www.national.com/refdesigns Power Management www.national.com/power Feedback www.national.com/feedback Switching Regulators www.national.com/switchers LDOs www.national.com/ldo LED Lighting www.national.com/led PowerWise www.national.com/powerwise Serial Digital Interface (SDI) www.national.com/sdi Temperature Sensors www.national.com/tempsensors Wireless (PLL/VCO) www.national.com/wireless THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION ("NATIONAL") PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL'S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright(c) 2008 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Technical Support Center Email: support@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Technical Support Center Email: europe.support@nsc.com German Tel: +49 (0) 180 5010 771 English Tel: +44 (0) 870 850 4288 National Semiconductor Asia Pacific Technical Support Center Email: ap.support@nsc.com National Semiconductor Japan Technical Support Center Email: jpn.feedback@nsc.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated