APEM www.apem.com B1-15
B1
IP series
Pushbutton switches for harsh environments - bushing Ø 12 mm - momentary
Distinctive features and specifications
❑Illuminated or non-illuminated
❑Tactile feedback
❑Wide variety of configurations
❑Flat round actuator for optional marking
❑Sealed to IP67
ENVIRONMENTAL SPECIFICATIONS
• Front panel sealing : IP67 according to IEC 60529
IP69K according to DIN 40050-9 (non-illuminated) with cap U5125
• Shock resistance : 100 g according to IEC 512-4, test 6c
• Vibration resistance : 10-500Hz - 10 g according to IEC 512-4, test 6d
• Salt spray : IEC 512-6, test 11f
• Robustness (non-illuminated) : IK06 according to EN 50102 (1 joule)
• Operating temperature : -40°C to +85°C
ELECTRICAL SPECIFICATIONS
• Max. current/voltage rating with resistive load (gold plated silver contacts):
5A 28VDC, 70.000 cycles
0,2A 48VDC, 500.000 cycles
0,5A 48VAC, 500.000 cycles
• Initial contact resistance : 100 mΩmax.
• Insulation resistance : 1 GΩmin. at 500VDC
• Dielectric strength : 1.500 Vrms
• Contact bounce : 10 ms
MATERIALS
• Case : thermoplastic UL94-V0
• Actuator :
polyamide
6/6
• Bushing/bezel : zinc die-cast
(zamac), black painted
• Contacts : silver, gold plated (std)
brass, gold plated (for option 104)
• Output wires
(flying lead terminals)
:
F version : AWG20, section 0,6 mm2
W version : AWG24, section 0,23 mm2
•
LED wires :
F version : AWG26, section 0,12 mm2
W version : AWG24, section 0,23 mm2
• Lens : polycarbonate
• Terminal seal : epoxy
GENERAL SPECIFICATIONS
• Panel thickness : 1,5 mm (.059) min.
4 mm (.157 max.)
• Total travel :
Funct. 3 : 1,7 mm (.067) +/- 0,3 mm
Funct. 5 : 1,3 mm (.051) +/- 0,3 mm
• Typical operating force : 6N +/- 2N
• Low level/mech. life : 1.000.000 cycles
• Torque : 1,5 Nm max. applied to nut
• Soldering : 320°C max. for 3 sec.
A resistor must be series-connected by the user.
Resistor value = supply voltage - LED forward voltage
LED forward current
LED COMPONENT SPECIFICATIONS
LED colour
Forward current
Super red (L0S) 20mA
20mA
20mA
20mA
Typ. forward voltage Max. forward voltage
2,1V
2,1V
2,1V
3,2V
Yellow (L0Y)
Green (L0G)
Blue (L0B)
20mA 3,35V
2,3V
2,3V
2,3V
3,8V
4,25VWhite (L0W) AGENCY APPROVAL
2A 125VAC/250VAC
File E83438
See following pages.
MOUNTING
Panel cut-out Matrix mounting
Back of panel space requirement
Ø13.60
(.535DIA)
(.531DIA)
Ø13.50
12.90
(.507)
1
1.50min-4Max
(.059 min-.157max)
20.00
(.787)
20.00
(.787)(.787)
20.00
(.688)
17.50
➀O-ring
For W terminals, current has to
be limited to 400mA.
04-Serie IP-A-R1-FilsFins_08-Serie IP-A 31/10/14 08:04 Page15
UG1410A
B1-16 APEMwww.apem.com
B1
IP series
Pushbutton switches for harsh environments - bushing Ø 12 mm - momentary
Overview
IP
SERIES
Actuator shapes
CSquare
RRound, curved
PRound, flat
Terminals
SSolder lugs
FFlying leads, standard
WFlying leads, thin NEW!
PStraight PC
Z1 Quick-connect
(non-ill., NO only )
Electrical functions
3Normally open
(NO)
5NC/NO combined
(non-illuminated)
Actuator colours
1Blue
BDark blue
2Black
3Green
4Grey
5Yellow
6Red
7/1 White
8Bright chrome
9Orange
ASatin chrome
Contacts
AD Silver, gold
plated (standard)
CD Brass, gold
plated (option 104)
LED colours
Blank Non-illum.
L0S Super red
L0Y Yellow
L0G Green
L0B Blue
L0W White
ABOUT THIS SERIES
On the following pages, you will find successively :
model structure of switches and options in the same order as in above chart
Dimensions : first dimensions are in mm while inches are shown as bracketed numbers.
A sealing boot is available to protect the switches against frost and sand. It is presented after the IA series and in section H.
Mounting accessories : Standard hardware supplied : 1 hex nut 14 mm (.551) across flats and 1 O-ring.
Hex nut part number U166.
Packaging unit : 25 pieces
NOTICE : please note that not all combinations of above numbers are available.
Refer to the following pages for further information.
Options
100 Satin chrome
bezel
101 Bright chrome
bezel
104 High actuator
(non-illum. round
models only)
Option 104
If combined with electrical function 5 (NC/NO), this
option should be ordered with CD contacts (brass, gold
plated). Current/voltage rating : 100mA 30VDC
Approval
UL
Consult factory for
detail of approved
models.
The company reserves the right to change specifications without notice.
04-Serie IP-A-R1-FilsFins_08-Serie IP-A 31/10/14 08:04 Page16
Function 3 (NO)
APEM www.apem.com B1-17
B1
IP series
Pushbutton switches for harsh environments - bushing Ø 12 mm - momentary
Square - illuminated
MODEL
STRUCTURE
• High brightness illumination
• Five LED colours
• Tin plated LED terminals
Solder lug terminals
Ø12.00x0.75SI
(.047)
1.50
5.20
(.015)
(.204)
(.059)
2.00
(.078)
5.08
(.200)
(.267)
1.20
(.251)
6.40 6.80
0.40
EPOXY
(.472DIAx0.75IS)
5.00
(.196)
1.50 Min
(.059 Min)
12.00
(.472SQ)
17.50
(.688SQ)
2.00
(.078)
6.10
(.240)
➞Flat
IPC3SAD Normally Open
Sealed flying lead terminals
Ø12.00x0.75SI
500±10
(19.68±.393)
(.688SQ)
1.50 Min
(.059 Min)
16.00 Max
(.629 Max)
6.80
(.267)
(.472DIAx0.75IS)
5.00
(.196)
12.00
(.472SQ)
(.078)
2.00
17.50
➞Flat
IPC3FAD Normally Open
Wire colours : black : NO contact, red : LED anode(+), blue : LED cathode(-)
Cathode
(-)
LED
ACTUATOR COLOURS
1: blue - B: dark blue - 2: black - 3: green - 4: grey
5: yellow - 6: red - 7/1 : white - 8: bright chrome
9: orange - A: satin chrome
LED COLOURS
OPTIONS
L0S : super red - L0Y : yellow - L0G : green - L0B : blue
L0W : white
100 : Satin chrome bezel
101 : Bright chrome bezel
APPROVAL
UL
Consult factory for details of approved models. To order
switches marked UL, complete above box with ”UL”.
Also available with straight PC terminals : IPC3PAD
LED colour is indicated by the bottom of the switch.
Shown with standard flying lead terminals.
For THIN flying leads, replace F with W.
04-Serie IP-A-R1-FilsFins_08-Serie IP-A 31/10/14 08:04 Page17
B1-18 APEMwww.apem.com
B1
IP series
Pushbutton switches for harsh environments - bushing Ø 12 mm - momentary
Square - non-illuminated
MODEL
STRUCTURE
• Double function (NC/NO combined)
with a short behind-panel depth
Solder lug terminals
Ø12.00x0.75SI
(.047)
1.50
5.20
(.204)
(.059)
2.00
(.078)
5.08
(.200)
(.015)
(.472DIAx0.75IS)
6.40
(.251)
1.20
6.80
(.267)
0.40
EPOXY
5.00
1.50 Min
(.196)
12.00
(.472SQ)
(.059 Min)
(.078)
17.50
(.688SQ)
2.00
NO NO
NC
NC/NONO
➞Flat
IPC3SAD Normally Open
IPC5SAD NC/NO combined
Sealed flying lead terminals
Ø12.00x0.75SI
500±10
(19.68±.393)
1.50 Min
(.059 Min)
(.472DIAx0.75IS)
(.267)
16.00 Max
(.629 Max)
6.80 5.00
(.196)
12.00
(.472SQ)
(.078)
2.00
17.50
(.688SQ)
NO NC/NO
➞Flat
IPC3FAD Normally Open
IPC5FAD NC/NO combined
ACTUATOR COLOURS
1: blue - B: dark blue -2: black - 3: green - 4: grey - 5: yellow - 6: red - 7/1 : white - 8: bright chrome
9: orange - A: satin chrome
OPTIONS
100 : Satin chrome bezel
101 : Bright chrome bezel
Wire colours (NC/NO) : black : NO, blue : NC
Function 3 (N0) Function 5 (NC/NO)
5.20
(.204)
1.00
(.039)
4.55
(.179)
Straight PQuick-connect Z1
Also available with straight PC terminals : IPC3PAD (NO) or IPC5PAD (NC/NO)
and quick-connect terminals : IPC3Z1AD (NO only)
APPROVAL
UL
Consult factory for details of approved models. To order
switches marked UL, complete above box with ”UL”.
Shown with standard flying lead terminals.
For THIN flying leads, replace F with W.
04-Serie IP-A-R1-FilsFins_08-Serie IP-A 31/10/14 08:04 Page18
APEM www.apem.com B1-19
B1
IP series
Pushbutton switches for harsh environments - bushing Ø 12 mm - momentary
Round - illuminated
MODEL
STRUCTURE
• High brightness illumination
• Five LED colours
• Tin plated LED terminals
Solder lug terminals
Ø12.00x0.75SI
Ø17.50
(.688DIA)
Ø12.00
(.472DIA)
(.047)
1.50
(.059)
(.204)
(.015)
5.20
(.200)
(.078)
2.00 5.08
EPOXY
0.40
(.472DIAx0.75IS)
(.267)(.251)
1.20
6.806.40
1.50 Min
5.00
(.059 Min)
(.196)
(.078)
2.00
6.10
(.240)
➞Flat
IPR3SAD Normally Open
Sealed flying lead terminals
Ø12.00x0.75SI
(19.68±.393)
500±10
Ø12.00
(.472DIA)
(.688DIA)
Ø17.50
(.196)
5.00
(.059 Min)
1.50 Min
2.00
(.078)
(.472DIAx0.75IS)
16.00 Max
(.629 Max) (.267)
6.80
➞Flat
IPR3FAD Normally Open
Wire colours : black : NO contact, red : LED anode(+), blue : LED cathode(-)
Cathode
(-)
LED
ACTUATOR COLOURS LED COLOURS
L0S : super red - L0Y : yellow - L0G : green - L0B : blue
L0W : white
APPROVAL
UL
Consult factory for details of approved models. To order
switches marked UL, complete above box with ”UL”.
Also available with straight PC terminals : IPR3PAD
LED colour is indicated by the bottom of the switch.
Cathode
(-)
LED
Shown with standard flying lead terminals.
1: blue - B: dark blue - 2: black - 3: green - 4: grey
5: yellow - 6: red - 7/1 : white - 8: bright chrome
9: orange - A: satin chrome
OPTIONS
100 : Satin chrome bezel
101 : Bright chrome bezel
For THIN flying leads, replace F with W.
Function 3 (NO)
04-Serie IP-A-R1-FilsFins_08-Serie IP-A 31/10/14 08:04 Page19
B1-20 APEMwww.apem.com
B1
IP series
Pushbutton switches for harsh environments - bushing Ø 12 mm - momentary
Round - non-illuminated
Function 3 (NO) Function 5 (NC/NO)
MODEL
STRUCTURE
• Double function (NC/NO combined)
with a short behind-panel depth
Solder lug terminals
NO
NO
NC
NC/NONO
2.00
(.078)
(.059 Min)
1.50 Min
(.196)
5.00
(.472DIAx0.75IS)
0.40
EPOXY
(.267)
6.80
1.20
6.40
(.251)
5.08
(.200)
2.00
(.078)
5.20
(.015)
(.204)
(.059)
1.50
(.047)
(.472DIA)
Ø12.00 (.688DIA)
Ø17.50
Ø12.00x0.75SI
➞Flat
Curved actuator, NO
IPR3SAD
Curved actuator, NC/NO
IPR5SAD
Flat actuator, NO
IPP3SAD
Flat actuator, NC/NO
IPP5SAD
Sealed flying lead terminals
NC/NONO
(.472DIAx0.75IS)
6.80
(.267)(.519)
13.20
(.078)
2.00
1.50 Min
(.059 Min)
5.00
(.196)
Ø17.50
(.688DIA)
(.472DIA)
Ø12.00
500±10
(19.68±.393)
Ø12.00x0.75SI
➞Flat
Curved actuator, NO
IPR3FAD
Curved actuator, NC/NO
IPR5FAD
Flat actuator, NO
IPP3FAD
Flat actuator, NC/NO
IPP5FAD
ACTUATOR COLOURS
Wire colours (NC/NO) : black : NO, blue : NC
100 : Satin chrome bezel
101 : Bright chrome bezel
104 : High actuator - If combined with function 5
(NC/NO), order with CD contacts (instead of AD contacts).
OPTIONS
5.20
(.204)
1.00
(.039)
4.55
(.179)
Straight PQuick-connect Z1
Also available with straight PC terminals : IP•3PAD (NO) or IP•5PAD (NC/NO)
and quick-connect terminals : IP•3Z1AD (NO only)
Actuator marking available on IPP models (symbol 10 mm max.). On request.
104 IPR 104 IPP
Ø12.00
(.472DIA)
(.185)
4.70
Ø12.00
(.472DIA)
(.185)
4.70
APPROVAL
UL
Consult factory for details of approved models. To order
switches marked UL, complete above box with ”UL”.
Shown with standard flying lead terminals.
For THIN flying leads, replace F with W.
1: blue - B: dark blue - 2: black - 3: green - 4: grey
5: yellow - 6: red - 7/1 : white - 8: bright chrome
9: orange - A: satin chrome
04-Serie IP-A-R1-FilsFins_08-Serie IP-A 31/10/14 08:04 Page20
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Apem:
IPR3PAD7/1 IPR3Z1AD2 IPR3Z1AD6 IP0207 IPR3SAD6104 IRP3S472