1/66
STE10/100
September 1999
This is preliminary information on a new product now in development. Details are subject to change without notice.
1.0 DESCRIPTION
The STE10/100 is a high performance PCI Fast Eth-
ernet controller with integrated physical layer inter-
face for 10BASE-T and 100BASE-TX application.
It was designed with advanced CMOS technology to
provide glueless 32-bit bus master interface for PCI
bus, boot ROM inter face, CSMA/CD prot ocol for Fast
Ethernet, as well as the physical media interface for
100BASE-TX of IEEE802.3u and 10BASE-T of
IEEE802.3. The auto-negotiation function is also
supported for speed and duplex detection.
The STE10/100 provides both half-duplex and full-
duplex operation, as well as support for full-duplex
flow control. It prov ides long FIFO buffers for trans-
mission and receiving, and early interrupt mecha-
nism to enhance performance. The STE10/100 also
supports ACPI and PCI compliant power manage-
ment function.
2.0 FEATURES
2.1 Industry standard
■IEEE802. 3u 100BASE-TX and IEEE802.3
10BASE-T co mp lian t
■Support for IEEE802.3x flow control
■IEEE802.3u A uto-Negotiation su pport for
10BASE-T a nd 1 00BASE-TX
■PCI bus interface Rev. 2.2 co mpliant
■ACP I and PCI power managem ent standard
compliant
■Support PC99 wake on LAN
2.2 FIFO
■Provides indepe ndent transm ission and
receiving FIFOs, each 2k bytes long
■P r e - fe tc h e s u p to tw o trans m it p a ck e ts to
minimize inter frame gap (IFG) to 0.96us
■Retransmits collided packet without reload from
host memory within 64 bytes.
■Automatically retransmits FIFO under-run
packet with maximum drain threshold until 3rd
time retry failure without influencing the
registers and transmit threshold of next packet.
PQFP128 (14x20x2.7mm)
ORDER ING NUMB ER: STE1 0/100
PRODUCT PREVIEW
PCI 10/100 ETHERNET CONTROLLER
WITH INTEGRATED PHY (5V)
Figure 1. STE10/100Block Diagram
Tx FiFo
DMA
Flow
Control
Manchester
Encoder
Manchester
Decoder
MII
Controller
10 T X
Filter
100 clock
Recover
y
10 clock
Recover
y
BaseLine
Restore Adaptive
Equalization
TX Freq.
S
y
nth.
Transmitter
Scrambler
Descrambler
Auto
Ne
g
otiation
4B/5B
5B/4B +
_
Link
Polarit
y
25Mhz
125Mhz
20Mhz
M AC SubLaye
MII Co n t r o ller
Rx FiFo
PCI Controller
STE10/100
2/66
2.3 PCI I/F
■Provides 32-bit PCI bus mas ter data transfer
■Supports PCI clock with frequency from 0Hz to 33MHz
■Supports network operation with PCI system clock from 20MHz to 33MHz
■Provides performance meter and PCI bus master latency timer for t uning the threshold to enhance the
performance
■Provides burst transmit packet interrupt and transmit/receive early interrupt to reduce host CPU
utilization
■As bus master, supports memory-read, memory-read-line, memory-read-multiple, memory-write,
memo ry-write-and-invalidate command
■Supports big or little endian byte ordering
2.4 EEPROM/Boot ROM I/F
■Provides writeable Flash ROM and EPR OM as boot ROM, up to 128kB
■Provides PCI to access boot ROM by byte, word, or double word
■Re-writes Flash boot ROM through I/O port by programming register
■Provides serial interface for read/write 93C46 EEPROM
■Automatically loads device ID, vendor ID, subsyst em ID, subsystem vendor ID, Maximum-Latency , and
Minimum -Grand f rom the 64 byte conten ts of 93C46 after PCI reset de-asserted
2.5 MAC/Physical
■Integrates the complete s et of Physical layer 100BA SE-T X and 10BASE- T fun c tion s
■Provides Full-d uplex operation in both 100M bps and 10Mbps modes
■Provides Auto-negotiation (NWAY) fun ction of full/half duplex operation for both 10 and 100 Mbps
■Provides MLT-3 transceiver with DC restoration for Base-line wander comp ensation
■Provides transmit wave-shaper, receive filters, and adaptive equalizer
■Provides MAC and Transceiver (TXC VR ) loop-back mode s for diagnost ic
■Built-in Stream Cipher Scrambler/ De-scrambler and 4B/5B encoder/de coder
■Supports external transmit transforme r with 1.414:1 turn ratio
■Supports external receive transformer with 1:1 turn ratio
2.6 LED Display
■Provides 2 LED display modes:
3 LED displays for
100Mbps (on) or 10Mbps (off)
Link (Remains on when link ok) or Activity (Blinks at 10Hz when receiving or transmitting collision-free)
FD (Remains on when in Full duplex mode) or when collision detected (Blinks at 20Hz)
4 LED displays for
100 Link (On when 100M link ok)
10 Link (On when 10M link ok)
Activity (Blinks at 10Hz when receiving or transmitting)
FD (Remains on when in Full duplex mode) or when collision detected (Blinks at 20Hz)
3/66
STE10/100
2.7 Miscellaneous
■ACPI and PCI compliant power man agem ent functions offer significant power-savings performance
■Provides general purpose tim ers
■128-pin QFP package
Figure 2. System Diagram of the STE10/ 100
STE10/100
Serial
EEPROM Boot ROM
LEDs 25 MHz
Crystal
Xfmr Medium
PCI
Interface
STE10/100
4/66
3.0 PIN ASSIGNEMENT DIAGRAM
Figure 3. Pin Connection
1
2
3
5
6
4
7
8
9
10
43
11
44 45 46 47 48
123122121120 118119 117116115114113
91
90
89
87
86
88
96
95
94
92
93
AD-23
VSS-PCI
IDSEL
AD-24
AD-25
C-BEB3
VSS-PCI
AD-20
AD-21
AD-22
VDD-PCI
VSS-IR
VDD-PCI
AD-8
AD-7
C-BEB0
AD-6
VSS-PCI
AD-5
AD-4
VDD-PCI
AD-29
VDD-PCI
AD-30
AD-31
REQ#
PME#
GNT#
PCI-CLK
VSS-PCI
RST#
INTA#
LED M1/M2
LED M1/M2
VCC-detect
BrA-16/LED M2
BrA-15
VCC-detect
AVSSX
AVDDREC
AVSSREC
LED M1/M2
VSS-IR
97
102
101
100
98
99
X2
AVSSI
IREF
AVDDI
X1
AVDDX
D99TL443
39 40 41 42
124
AD-28
125
VSS-PCI
126
AD-27
127
AD-26
128
VDD-PCI
85
84
82
81
83
VDD-IR
BrA-14
BrA-12
BrA-11
BrA-13
12
13
14
15
16AD-16
AD-17
VDD-PCI
AD-19
AD-18
51 52 53 54 55 56
112 110111 109108107106105
AD-3
VSS-PCI
AD-2
AD-1
AD-0
N.C.
VSS-IR
BrA -0
VSS-IR
AVSST
VDD-IR
TX-
AVDDT
TX+
AVSSR
RX+
49 50
17
18
19
79
78
80
VSS-PCI
FRAME#
C-BEB2
BrWE#
BrOE#
BrA-10
77
76
74
73
75
BrCS#
EECS
BrD-7/ECK
BrD-6/EDI
VSS-IR
20
21
22
23
24PERR#
STOP#
DEVSEL#
IRDY#
TRDY#
25
26
27
71
70
72
VDD-PCI
PAR
SERR#
BrD-4
BrD-3
BrD-5/EDO
69
68
66
65
67
BrD-2
BrD-1
BrA-9
BrA-8
BrD-0
28
29
30
31
32AD-13
VSS-PCI
AD-14
C-BEB1
AD-15
33AD-12
34
35
36
37
38VDD-IR
AD-9
VSS-PCI
AD-11
AD-10
59 60 61 62 63 64
104103
BrA-1
BrA-3
BrA-2
VDD-IR
BrA-4
BrA-5
BrA6
BrA-7
RX-
AVDDR
57 58
5/66
STE10/100
4.0 4. PIN DESCRIPTION
Table 1. Pin Description
Pin No. Name Type Description
PCI bus Interface
113 INTA# O/D PCI interrupt request. STE10/100 asserts this signal when one of the interrupt
event is set.
114 RST# I PCI Reset signal to initialize the STE10/100. The RST signal should be asserted
for at least 100µs to ensure that the STE10/100 completes initialization. During
the reset period, all the output pins of STE10/100 will be placed in a high-
impedance state and all the O/D pins are floated.
116 PCI-CLK I PCI clock input to STE10/100 for PCI Bus functions. The Bus signals are
synchronized relative to the rising edge of PCI-CLK PCI-CLK must operate at a
frequency in the range between 20MHz and 33MHz to ensure proper network
operation
117 GNT# I PCI Bus Granted. This signal indicates that the STE10/100 has been granted
ownership of the PCI Bus as a result of a Bus Request.
118 REQ# O PCI Bus Request. STE10/100 asserts this line when it needs access to the PCI
Bus.
119 PME# O
OD The Power Management Event signal is an open drain, active low signal. The
STE10/100 will assert PME# to indicate that a power management event has
occurred.
When WOL (bit 18 of CSR18) is set, the STE10/100 is placed in Wake On LAN
mode. While in this mode, the STE10/100 will activate the PME# signal upon
receipt of a Magic Packet frame from the network.
In the Wake On LAN mode, when LWS (bit 17 of CSR18) is set, the LAN-WAKE
signal follows HP’s protocol; otherwise, it is IBM protocol.
120,121
123,124
126,127
1,2
6,7
9,10
12,13
15,16
29,30
32~35
37
41
43,44
46,47
49,50
52,53
AD-31,30
AD-29,28
AD-27,26
AD-25,24
AD-23,22
AD-21,20
AD-19,18
AD-17,16
AD-15,14
AD-13~10
AD-9
AD-8
AD-7, 6
AD-5,4
AD-3,2
AD-1,0
I/O Multiplexed PCI Bus address/data pins
3
17
28
42
C-BEB3
C-BEB2
C-BEB1
C-BEB0
I/O Bus command and byte enable
4 IDSEL I Initialization Device Select. This signal is asserted when the host issues
configuration cycles to the STE10/100.
18 FRAME# I/O Asserted by PCI Bus master during bus tenure
20 IRDY# I/O Master device is ready to begin data transaction
STE10/100
6/66
21 TRDY# I/O Target device is ready to begin data transaction
22 DEVSEL# I/O Device select. Indicates that a PCI target device address has been decoded
23 STOP# I/O PCI target device request to the PCI master to stop the current transaction
24 PERR# I/O Data parity error detected, driven by the device receiving data
25 SERR# O/D Address parity error
26 PAR I/O Parity. Even parity computed for AD[31:0] and C/BE[3:0]; master drives PAR for
address and write data phase, target drives PAR for read data phase
BootROM/E EPROM Interf ace
56~59
61~66
80~86
87
BrA0~3
BrA4~9
BrA10~15
BrA16/
LED M2 -
Fd/Col
I/O ROM data bus
Provides up to 128kB EPROM or Flash-ROM application space.
This pin can be programmed as mode 2 LED display for Full Duplex or Collision
status. It will be driven (LED on) continually when a full duplex configuration is
detected, or it will be driven at a 20 Hz blinking frequency when a collision status
is detected in the half duplex configuration.
67~71
72
73
74
BrD0~4
BrD5/EDO
BrD6/EDI
BrD7/ECK
O
O/I
O/O
O/O
BootROM data bus (0~7)
EDO: Data output of serial EEPROM, data input to STE10/100
EDI:Data input to serial EEPROM, data output from STE10/100
ECK:Clock input to serial EEPROM, sourced by STE10/100
76 EECS O Chip Select of serial EEPROM
77 BrCS# O BootROM Chip Select
78 BrOE# O BootROM Read Output Enable for flash ROM application
79 BrWE# O BootROM Write Enable for flash ROM application.
Physical Interface
98 X1 I 25 MHz reference clock input for Physical portion. When an external 25 MHz
crystal is used, this pin will be connected to one of its terminals, and X2 will be
connected to the other terminal. If an external 25 MHz oscillator is used, then this
pin will be connected to the oscillator’s output pin.
97 X2 O 25 MHz reference clock output for Physical portion. When an external 25MHz
crystal is used, this pin will be connected to one of the crystal terminals (see X1,
above). If an external clock source is used, then this pin should be left open.
107,109 TX+, TX- O The differential Transmit outputs of 100BASE-TX or 10BASE-T, these pins
connect directly to Magnetic.
105,104 RX+, RX- I The differential Receive inputs of 100BASE-TX or 10BASE-T, these pins connect
directly from Magnetic.
101 Iref O Reference Resistor connecting pin for reference current, directly connects a 5K
Ohm ± 1% resistor to Vss.
Table 1. Pin Description
Pin No. Name Type Description
7/66
STE10/100
LED display & Miscellaneous
90 LED M1-
LK/Act
or
LED M2-
Act
O This pin can be programmed as mode 1 or mode 2:
For mode 1:
LED display for Link and Activity status. This pin will be driven on continually
when a good Link test is detected. This pin will be driven at a 10 Hz blinking
frequency when either effective receiving or transmitting is detected.
For mode 2:
LED display for Activity status. This pin will be driven at a 10 Hz blinking
frequency when either effective receiving or transmitting is detected.
92 LED M1-
Speed
or
LED M2-
100 Link
O This pin can be programmed as mode 1 or mode 2:
For mode 1:
LED display for 100M b/s or 10M b/s speed. This pin will be driven on continually
when the 100M b/s network operating speed is detected.
For mode 2:
LED display for 100Ms/s link status. This pin will be driven on continually when
100Mb/s network operating spped is detected.
91 LED M1-
Fd/Col
or
LED M2-
10 Link
O This pin can be programmed as mode 1 or mode 2:
For mode 1:
LED display for Full Duplex or Collision status. This pin will be driven on
continually when a full duplex configuration is detected. This pin will be driven at
a 20 Hz blinking frequency when a collision status is detected in the half duplex
configuration.
For mode 2:
LED display for 10Ms/s link status. This pin will be driven on continually when
10Mb/s network operating speed is detected.
89 Vaux-
detect I When this pin is asserted, it indicates an auxiliary power source is supported
from the system.
88 Vcc-detect I When this pin is asserted, it indicates a PCI power source is supported.
Digital Power Pins
5,11,19,31,36,39,45,51,55,75,93,112,115,125 Vss
8,14,27,38,40,48,60,85,111,122,128 Vdd
Analog Power Pins
94,96,102,106,110 AVss
95,99,100,103,108 AVdd
Table 1. Pin Description
Pin No. Name Type Description
STE10/100
8/66
5.0 REGISTERS AND DESCRIPTORS DESCRIPTION
There are three kinds of registers within the STE10/100: STE10/100 configuration registers, PCI control/status
registers, and Transceiver control/status registers.
The STE10/100 configuration registers are used to initialize and configure the STE10/100 and for identifying
and querying the STE10/100.
The PCI control/status registers are used to communicate between the host and STE10/100. The host can ini-
tialize, control, and read the status of the ST E10/100 through mapped I/O or memory address space.
The STE10/100 contains 11 16-bit registers to supported Transceiver control and status. They include 7 basic
regi sters whi ch are defined ac cording to cl ause 22 “ Reconcili ation Sub- layer and Media Ind ependent Inter face”
and clause 28 “Physical Layer link signaling for 10 Mb/s and 100 Mb/s Auto-Negotiation on twisted pair” of the
IEEE802.3u standard. In addition, 4 special registers are provided for advanced chip control and status.
The STE10/100 also provides receive and transmit descriptors for packet buffering and management.
5.1 STE10/100 Configuration Registers
An STE10/100 software driver can initialize and configure the chip by writing its configuration registers. The
contents of configuration registers are set to their default values upon power-up or whenever a hardware reset
occurs, but their settings remain unchanged whenever a software reset occurs. The configuration registers are
byte, word, and double word accessible.
Table 2. STE10/10 0 configu ration register s list
Offset Index Name Descriptions
00h CR0 LID Loaded device ID and vendor ID
04h CR1 CSC Configuration Status and Command
08h CR2 CC Class Code and revision number
0ch CR3 LT Latency Timer
10h CR4 IOBA IO Base Address
14h CR5 MBA Memory Base Address
2ch CR11 SID Subsystem ID and vendor ID
30h CR12 BRBA Boot ROM Base Address (ROM size = 128KB)
34h CR13 CP Capability Pointer
3ch CR15 CINT C onfig uration Interr up t
40h CR16 DS driver space for special purpose
80h CR32 SIG Signature of STE10/100
c0h CR48 PMR0 Power Management Register 0
c4h CR49 PMR1 Power Management Register 1
9/66
STE10/100
Table 3. STE10/100 configuration registers table
Note: * : automatically recalled from EEPROM when PCI reset is deserted
DS(40h), bit15-8, is read/write able register
SIG(80h) is hard wired registe r, read only
5.1.1 STE10/ 100 conf iguration registers des criptions
offset b31 ----------- b16 b15 ---------- b0
00h Device ID* Vendor ID*
04h Status Command
08h Base Class Code Subclass ------ Revision # Step #
0ch ------ ------ Latency timer cache line size
10h Base I/O address
14h Base memory address
18h~
28h Reserved
2ch Subsystem ID* Subsystem vendor ID*
30h Boot ROM base address
34h Reserved Cap_Ptr
38h Reserved
3ch Max_Lat* Min_Gnt* Interrupt pin Interrupt line
40h Reserved Driver Space Reserved
80h Signature of STE10/100
c0h PMC Next_Item_Ptr Cap_ID
c4h Reserved PMCSR
Table 4. Configuration Registers Descriptions
Bit # Name Descrip tions Default Val RW Type
CR0(offset = 00h), LID - Loaded Identification number of Device and Vendor
31~16 LDID Loaded Device ID, the device ID number loaded from serial
EEPROM. From
EEPROM R/O
15~0 LVID Loaded Vendor ID, the vendor ID number loaded from serial
EEPROM. From
EEPROM R/O
From EEPRO M: Loade d from EEPROM
CR1(offset = 04h), CSC - Configuration command and status
31 SPE Status Pa rity Error.
1: means that STE10/100 detected a parity error. This bit will
be set even if the parity error response (bit 6 of CR1) is
disabled.
0 R/W
30 SES Status Syste m Error.
1: means that STE10/100 asserted the system error pin. 0 R/W
STE10/100
10/66
29 SMA Status Master Abort.
1: means that STE10/100 received a master abort and has
terminated a master transaction.
0 R/W
28 STA Status Target Abort.
1: means that STE10/100 received a target abort and has
terminated a master transaction.
0 R/W
27 --- Reserved.
26, 25 SDST Status Device Select Timing. Indicates the timing of the chip’s
assertion of device select.
01: indicates a medium assertion of DEVSEL#
01 R/O
24 SDPR Status Data Parity Repor t.
1: when three conditions are met:
a. STE10/100 asserted parity error (PERR#) or it detected
parity error asserted by another device.
b. STE10/100 is operating as a bus master.
c. STE10/100’s parity error response bit (bit 6 of CR1) is
enabled.
0 R/W
23 S FBB St atus Fast Back-to-Back
Always 1, since STE10/100 has the ability to accept fast back
to back transactions.
1 R/O
22~21 --- Reserved.
20 NC New Capabilities. Indicates whether the STE10/100 provides a
list of extended capabilities, such as PCI power management.
1: the STE10/100 provides the PCI management function
0: the STE10/100 doesn’t provide New Capabilities.
Same as
bit 19 of
CSR18
RO
19~ 9 --- Reserved.
8 CSE Command System Error Response
1: enable system error response. The STE10/100 will assert
SERR# when it finds a parity error during the address phase.
0 R/W
7 --- Reserved.
6 CPE Command Parity Error Response
0: disable parity error response. STE10/100 will ignore any
detected parity error and keep on operating. Default value is
0.
1: enable parity error response. STE10/100 will assert system
error (bit 13 of CSR5) when a parity error is detected.
0 R/W
5~ 3 --- Reserved.
2 CMO Command Master Operation Ability
0: disable the STE10/100 bus master ability.
1: enable the PCI bus master ability. Default value is 1 for
normal operation.
0 R/W
1 CMSA Command Memory Space Access
0: disable the memory space access ability.
1: enable the memory space access ability.
0 R/W
Table 4. Configuration Registers Descriptions
Bit # Name Descrip tions Default Val RW Type
11/66
STE10/100
0 CIOSA Command I/O Space Access
0: enable the I/O space access ability.
1: disable the I/O space access ability.
0 R/W
R/W: R ead and Wri te able. R O: Read ab le on ly.
CR2(offset = 08h), CC - Class Code and Revision Number
31~24 BCC Base Class Code. It means STE10/100 is a network controller. 02h RO
23~16 SC Subclass Code. It means STE10/100 is a Fast Ethernet
Controller. 00h RO
15~ 8 --- Reserved.
7 ~ 4 RN Revision Number, identifies the revision number of STE10/
100. Ah RO
3 ~ 0 SN Step Number, identifies the STE10/100 steps within the
current revision. 1h RO
RO: Rea d Only.
CR3(offset = 0ch), LT - Latency Timer
31~16 --- Reserved.
15~ 8 LT Latency Timer. This value specifies the latency timer of the
STE10/100
in units of PCI b us clock cycles. Once the STE10/100
asserts FRAME#, the latency timer starts to count. If the
latency timer expires and the STE10/100 is still asserting
FRAME#, the STE10/100 will terminate the data transaction
as soon as its GNT# is removed.
0 R/W
7 ~ 0 CLS Cache Line Size. This value specifies the system cache line
size in units of 32-bit double words(DW). The STE10/100
supports cache line sizes of 8, 16, or 32 DW. CLS is used by
the STE10/100 driver to program the cache alignment bits (bit
14 and 15 of CSR0) which are used for cache oriented PCI
commands, e.g., memory-read-line, memory-read-multiple,
and memory-write-and-invalidate.
0 R/W
CR4(offset = 10h), IOBA - I/O Base Address
31~ 7 IOBA I/O Base Address. This value indicate the base address of PCI
control and status register (CSR0~28), and Transceiver
registers (XR0~10)
0 R/W
6 ~ 1 --- reserved.
0 IOSI I/O Space Indicator.
1: means that the configuration registers map into I/O space. 1RO
CR5(offset = 14h), MBA - Memory Base Address
31~ 7 MBA Memory Base Address. This value indicate the base address
of PCI control and status register(CSR0~28), and Transceiver
registers(XR0~10)
0 R/W
6 ~ 1 --- reserved.
Table 4. Configuration Registers Descriptions
Bit # Name Descrip tions Default Val RW Type
STE10/100
12/66
0 IOSI Memory Space Indicator.
1: means that the configuration registers map into I/O space. 0RO
CR11(offset = 2ch), SID - Subsystem ID.
31~16 SID Subsystem ID. This value is loaded from EEPROM as a result
of power-on or hardware reset. From
EEPROM RO
15~ 0 SVID Subsystem Vendor ID. This value is loaded from EEPROM as
a result power-on or hardware reset. From
EEPROM RO
CR12(offset = 30h), BRBA - Boot ROM Base Address. This register should be initialized before accessing the
boot ROM space.
31~10 BRBA Boot ROM Base Address. This value indicates the address
mapping of the boot ROM field as well as defining the boot
ROM size. The values of bit 16~10 are set to 0 indicating that
the STE10/100 supports up to 128kB of boot ROM.
X: b31~17
0: b16~10 R/W
RO
9 ~ 1 --- reserved RO R/W R/
W
0 BRE Boot ROM Enable. The STE10/100 will only enable its boot
ROM access if both the memory space access bit (bit 1 of
CR1) and this bit are set to 1.
1: enable Boot ROM. (if bit 1 of CR1 is also set)
0 R/W
CR13(offset = 34h), CP - Capabilities Pointer.
31~8 --- reserved
7~0 CP Capabilities Pointer. C0H RO
CR15(offset = 3ch), CI - Configuration Interrupt
31~24 ML Max_Lat register. This value indicates how often the STE10/
100 needs to access to the PCI bus in units of 250ns. This
value is loaded from serial EEPROM as a result of power-on or
hardware reset.
From
EEPROM RO
23~16 MG Min_Gnt register. This value indicates how long the STE10/
100 needs to retain the PCI bus ownership whenever it
initiates a transaction, in units of 250ns. This value is loaded
from serial EEPROM as a result power-on or hardware reset.
From
EEPROM RO
15~ 8 IP Interrupt Pin. This value indicates one of four interrupt request
pins to which the STE10/100 is connected.
01h: means the STE10/100 always connects to INTA#
01h RO
7 ~ 0 IL Interrupt Line. This value indicates the system interrupt
request lines to which the INTA# of STE10/100 is routed. The
BIOS will fill this field when it initializes and configures the
system. The STE10/100 driver can use this value to determine
priority and vector information.
0 R/W
CR16(offset = 40h), DS - Driver Space for special purpose.
31~16 --- reserved
Table 4. Configuration Registers Descriptions
Bit # Name Descrip tions Default Val RW Type
13/66
STE10/100
15~8 DS Driver Space for implementation-specific purpose. Since this
area won’t be cleared upon software reset, an STE10/100
driver can use this R/W area as user-specified storage.
0 R/W
7 ~ 0 --- reserved
CR32(offset = 80h), SIG - Signature of STE10/100
31~16 DID Device ID, the device ID number of the STE10/100. 0981h RO
15~0 VID Vendor ID 1317h RO
CR48(offset = c0h), PMR0, Power Management Register0.
31
30
29
28
27
PSD3c,
PSD3h,
PSD2,
PSD1,
PSD0
PME_Support.
The STE10/100 will assert PME# signal while in the D0, D1,
D2, D3hot and D3cold power state. The STE10/100 supports
Wake-up from the above five states. Bit 31 (support wake-up
from D3cold) is loaded from EEPROM after power-up or
hardware reset. To support the D3cold wake-up function, an
auxiliary power source will be sensed during reset by the
STE10/100 Vaux_detect pin. If sensed low, PSD3c will be set
to 0; if sensed high, and if D3CS (bit 31of CSR18) is set
(CSR18 bits 16~31 are recalled from EEPROM at reset), then
bit 31 will be set to 1.
X1111b RO
26 D2S D2_Support. The STE10/100 supports the D2 Power
Management State. 1RO
25 D1S D1_Support. The STE10/100 supports the D1 Power
Management State. 1RO
24~22 AUXC Aux Current. These three bits report the maximum 3.3Vaux
current requirements for STE10/100 chip. If bit 31 of PMR0 is
‘1’, the default value is 111b, meaning the STE10/100 need s
375 mA to support remote wake-up in D3cold power state.
Otherwise, the default value is 000b, meaning the STE10/100
does not support remote wake-up from D3cold power state.
XXXb RO
21 DSI The Device Specific Initialization bit indicates whether any
special initialization of this function is required before the
generic class device driver is able to use it.
0: indicates that the function does not require a device-specific
initialization sequence following transition to the D0
uninitialized state.
0RO
20 --- Reserved.
19 PMEC PME Clock. Indicates that the STE10/100 does not rely on the
presence of the PCI clock for PME# operation 0RO
18~16 VER Version. The value of 010b indicates that the STE10/100
complies with Revision 1.0a of the PCI Power Management
Interface Specification.
010b RO
15~8 NIP Next Item Pointer. This value is always 0h, indicating that
there are no additional items in the Capabilities List. 00h RO
7~0 CAPID Capability Identifier. This value is always 01h, indicating the
link list item as being the PCI Power Management Registers. 01h RO
Table 4. Configuration Registers Descriptions
Bit # Name Descrip tions Default Val RW Type
STE10/100
14/66
CR49(offset = c4h), PMR1, Power Management Register 1.
31~16 --- reserved
15 PMEST PME_Status. This bit is set whenever the STE10/100 detects
a wake-up event, regardless of the state of the PME-En bit.
Writing a “1” to this bit will clear it, causing the STE10/100 to
deassert PME# (if so enabled). Writing a “0” has no effect.
If PSD3c (bit 31 of PMR0) is cleared (i.e. it does not support
PME# generation from D3cold), this bit is by default 0;
otherwise, PMEST is cleared upon power-up reset only and is
not modified by either hardware or software reset.
X R/W1C*
14,13 DSCAL Data_Scale. Indicates the scaling factor to be used when
interpreting the value of the Data register. This field is
required for any function that implements the Data register.
The STE10/100 does not support Data register and
Data_Scale.
00b RO
12~9 DSEL Data_Select. This four bit field is used to select which data is
to be reported through the Data register and Data_Scale field.
This field is required for any function that implements the Data
register.
The STE10/100 does not support Data_select.
0000b R/W
8 PME_En PME_En. When set, enables the STE10/100 to assert PME#.
When cleared, disables the PME# assertion.
If PSD3c (bit 31 of PMR0) is cleared (i.e. it does not support
PME# generation from D3cold), this bit is by default 0;
otherwise, PME_En is cleared upon power up reset only and is
not modified by either hardware or software reset.
X R/W
7~2 --- reserved. 000000b RO
1,0 PWRS PowerState. This two bit field is used both to determine the
current power state of the STE10/100 and to place the STE10/
100 in a new power state. The definition of this field is given
below.
00b - D0
01b - D1
10b - D2
11b - D3hot
If software attempts to write an unsupported state to this field,
the write operation will complete normally on the bus, but the
data is discarded and no state change occurs.
00b R/W
R/W1C * , Read Onl y and Write one cleared.
Table 4. Configuration Registers Descriptions
Bit # Name Descrip tions Default Val RW Type
15/66
STE10/100
5.2 PCI Control/Status registers
Table 5. PCI Control/Status reg ister s list
offset from base
address of CSR Index Name Descriptions
00h CSR0 PAR PCI acces s register
08h CSR1 TDR transmit demand register
10h CSR2 RDR receive demand register
18h CSR3 RDB receive descriptor base address
20h CSR4 TDB transmit descriptor base address
28h CSR5 SR status register
30h CSR6 NAR network access register
38h CSR7 IER interrupt enable register
40h CSR8 LPC lost packet counter
48h CSR9 SPR serial port register
50h CSR10 --- Reserved
58h CSR11 TMR Timer
60h CSR12 --- Reserved
68h CSR13 WCSR Wake-up Control/Status Register
70h CSR14 WPDR Wake-up Pattern Data Register
78h CSR15 WTMR watchdog timer
80h CSR16 ACSR5 status register 2
84h CSR17 ACSR7 interrupt enable register 2
88h CSR18 CR command register
8ch CSR 19 PC IC PCI bus performance counter
90h CSR20 PMCSR Power Management Command and Status
94h CSR21 --- Reserved
98h CSR22 --- Reserved
9ch CSR23 TXBR transmit burst counter/time-out register
a0h CSR24 FROM flash(boot) ROM port
a4h CSR25 PAR0 physical address register 0
a8h CSR26 PAR1 physical address register 1
ach CSR27 MAR0 multicast address hash table register 0
b0h CSR28 MAR1 multicast address hash table register 1
STE10/100
16/66
Table 6. Control/Status reg ister description
Bit # Name Descrip tions Default Val RW Type
CSR0(offset = 00h), PAR - PCI Access Register
31~25 --- reserved
24 MWIE Memory Write and Invalidate Enable.
1: enable STE10/100 to generate memory write invalidate
command. The STE10/100 will generate this command
while writing full cache lines.
0: disable generating memory write invalidate command. The
STE10/100 will use memory write commands instead.
0 R/W*
23 MRLE Memory Read Line Enable.
1: enable STE10/100 to generate memory read line command
when read access instruction reaches the cache line
boundary. If the read access instruction doesn’t reach the
cache line boundary then the STE10/100 uses the memory
read command instead.
0 R/W*
22 --- reserved
21 MRME Memory Read Multiple Enable.
1: enable STE10/100 to generate memory read multiple
commands when reading a full cache line. If the memory is
not cache-aligned, the STE10/100 uses the memory read
command instead.
0 R/W*
20~19 --- reserved
18,17 TAP Transmit auto-polling in transmit suspended state.
00: disable auto-polling (default)
01: polling own-bit every 200 us
10: polling own-bit every 800 us
11: polling own-bit every 1600 us
00 R/W*
16 --- reserved
15, 14 CAL Cache alignment. Address boundary for data burst, set after
reset
00: reserved (default)
01: 8 DW boundary alignment
10: 16 DW boundary alignment
11: 32 DW boundary alignment
00 R/W*
13 ~ 8 PBL Programmable Burst Length. This value defines the maximum
number of DW to be transferred in one DMA transaction.
value: 0 (unlimited), 1, 2, 4, 8, 16(default), 32
010000 R/W*
7 BLE Big or Little Endian selection.
0: little endian (e.g. INTEL)
1: big endian (only for data buffer)
0 R/W*
6 ~ 2 DSL Descriptor Skip Length. Defines the gap between two
descriptors in the units of DW. 0 R/W*
1 BAR Bus arbitration
0: receive operations have higher priority
1: transmit operations have higher priority
0 R/W*
17/66
STE10/100
0 SWR Software reset
1: reset all internal hardware (including MAC and
transceivers), except configuration registers. This signal will be
cleared by the STE10/100 itself after the reset process is
completed.
0 R/W*
R/W* = Before writi ng the transmit and receive operati ons should be stopped.
CSR1(offset = 08h), TDR - Transmit demand register
31~ 0 TPDM Transmit poll demand.
While the STE10/100 is in the suspended state, a write to this
register (any value) will trigger the read-tx-descriptor process,
which checks the own-bit; if set, the transmit process is then
started.
FFFFFFFF
hR/W*
R/W* = Before writi ng the transmit proc ess should be in the suspended stat e.
CSR2(offset = 10h), RDR - Receive demand register
31 ~ 0 RPDM Receive poll demand
While the STE10/100 is in the suspended state, a write to this
register (any value) will trigger the read-rx-descriptor process,
which checks the own-bit, if set, the process to move data from
the FIFO to buffer is then started.
FFFFFFFF
hR/W*
R/W* = Before writi ng the receive process should be in the suspende d state.
CSR3(offset = 18h), RDB - Receive descriptor base address
31~ 2 SAR Start address of receive descriptor 0 R/W*
1, 0 RBND must be 00, DW boundary 00 RO
R/W* = Before writi ng the receive process should be stopped.
CSR4(offset = 20h), TDB - Transmit descriptor base address
31~ 2 SAT Start address of transmit descriptor 0 R/W*
1, 0 TBND must be 00, DW boundary 00 RO
R/W* = Before writi ng the transmit proc ess should be stopped.
CSR5(offset = 28h), SR - Status register
31~ 26 ---- reserved
25~ 23 BET Bus Error Type. This field is valid only when bit 13 of
CSR5(fatal bus error) is set. There is no interrupt generated by
this field.
000: parity error, 001: master abort, 010: target abort
011, 1xx: reserved
000 RO
Table 6. Control/Status reg ister description
Bit # Name Descrip tions Default Val RW Type
STE10/100
18/66
22~ 20 TS Transmit State. Reports the current transmission state only, no
interrupt will be generated.
000: stop
001: read descriptor
010: transmitting
011: FIFO fill, read the data from memory and put into FIFO
100: reserved
101: reserved
110: suspended, unavailable transmit descriptor or FIFO
overflow
111: write descriptor
000 RO
19~17 RS Receive State. Repor ts curre nt receive state only, no interrupt
will be generated.
000: stop
001: read descriptor
010: check this packet and pre-fetch next descriptor
011: wait for receiving data
100: suspended
101: write descriptor
110: flush the current FIFO
111: FIFO drain, move data from receiving FIFO into memory
000 RO
16 NISS Normal Interrupt Status Summary. Set if any of the following
bits of CSR5 are asserted:
TCI, transmit completed interrupt (bit 0)
TDU, transmit descriptor unavailable (bit 2)
RCI, receive completed interrupt (bit 6)
0 RO/LH*
15 AISS Abnormal Interrupt Status Summary. Set if any of the following
bits of CSR5 are asserted:
TPS, transmit process stopped (bit 1)
TJT, transmit jabber timer time-out (bit 3)
TUF, transmit under-flow (bit 5)
RDU, receive descriptor unavailable (bit 7)
RPS, receive process stopped (bit 8)
RWT, receive watchdog time-out (bit 9)
GPTT, general purpose timer time-out (bit 11)
FBE, fatal bus error (bit 13)
0 RO/LH*
14 ---- reserved
13 FBE Fatal Bus Error.
1: on occurrence of parity error, master abort, or target abort
(see bits 25~23 of CSR5). The STE10/100 will disable all bus
access. A software reset is required to recover from a parity
error.
0 RO/LH*
12 --- reserved
11 GPTT General Purpose Timer Timeout, based on CSR11 timer
register 0 RO/LH*
10 --- reserved
9 RWT Receive Watchdog Timeout, based on CSR15 watchdog timer
register 0 RO/LH*
8 RPS Receive Process Stopped, receive state = stop 0 RO/LH*
Table 6. Control/Status reg ister description
Bit # Name Descrip tions Default Val RW Type
19/66
STE10/100
7 RDU Receive Descriptor Unavailable
1: when the next receive descriptor can not be obtained by the
STE10/100. The receive process is suspended in this
situation. To restart the receive process, the ownership bit of
the next receive descriptor should be set to STE10/100 and a
receive poll demand command should be issued (if the receive
poll demand is not issued, the receive process will resume
when a new recognized frame is received).
0 RO/LH*
6 RCI Receive Completed Interrupt
1: when a frame reception is completed. 0 RO/LH*
5 TUF Transmit Under-Flow
1: when an under-flow condition occurs in the transmit FIFO
during transmitting. The transmit process will enter the
suspended state and report the under-flow errror on bit 1 of
TDES0.
0 RO/LH*
4 --- Reserved
3 TJT Transmit Jabber Timer Time-out
1: when the transmit jabber timer expires. The transmit
processor will enter the stop state and TO (bit 14 of TDES0,
transmit jabber time-out flag) will be asserted.
0 RO/LH*
2 TDU Transmit Descriptor Unavailable
1: when the next transmit descriptor can not be obtained by
the STE10/100. The transmission process is suspended in this
situation. To restart the transmission process, the ownership
bit of the next transmit descriptor should be set to STE10/100
and, if the transmit automatic polling is not enabled, a transmit
poll demand command should then be issued.
0 RO/LH*
1 TPS Transmit Process Stopped.
1: while transmit state = stop 0 RO/LH*
0 TCI Transmit Completed Interrupt.
1: set when a frame transmission completes with IC (bit 31 of
TDES1) asserted in the first transmit descriptor of the frame.
0 RO/LH*
LH = High Latching and cleared by writing 1.
CSR6(offset = 30h), NAR - Network access register
31~22 --- reserved
21 SF Store and forward for transmit
0: disable
1: enable, ignore the transmit threshold setting
0 R/W*
20 --- reserved
19 SQE SQE Disable
0: enable SQE function for 10BASE-T operation. The STE10/
100 provides SQE test function for 10BASE-T half duplex
operation.
1: disable SQE function.
1 R/W*
18~16 ----- reserved
Table 6. Control/Status reg ister description
Bit # Name Descrip tions Default Val RW Type
STE10/100
20/66
15~14 TR transmit threshold control
00: 128-bytes (100Mbps), 72-bytes (10Mbps)
01: 256-bytes (100Mbps), 96-bytes (10Mbps)
10: 512-bytes (100Mbps), 128-bytes (10Mbps)
11: 1024-bytes (100Mbps), 160-bytes (10Mbps)
00 R/W*
13 ST Stop transmit
0: stop (default)
1: start
0 R/W
12 FC Force collision mode
0: disable
1: generate collision upon transmit (for testing in loop-back
mode)
0 R/W**
11, 10 OM Operating Mode
00: normal
01: MAC loop-back, regardless of contents of XLBEN (bit 14 of
XR0, XCVR loop-back)
10,11: reserved
00 R/W**
9, 8 --- reserved
7 MM Multicast Mode
1: receive all multicast packets 0 R/W***
6 PR Promiscuous Mode
1: receive any good packet.
0: receive only the right destination address packets
1 R/W***
5 SBC Stop Back-off Counter
1: back-off counter stops when carrier is active, and resumes
when carrier is dropped.
0: back-off counter is not effected by carrier
0 R/W**
4 --- reserved
3 PB Pass Bad packet
1: receives any packets passing address filter, including runt
packets, CRC error, truncated packets. For receiving all
bad packets, PR (bit 6 of CSR6) should be set to 1.
0: filters all bad packets
0 R/W***
2 --- reserved
1 SR Start/Stop Receive
0: receive processor will enter stop state after the current
frame reception is completed. This value is effective only
when the receive processor is in the running or suspending
state. Note: In “Stop Receive” state, the PA USE packet and
Remote Wake Up packet will not be affected and can be
received if the corresponding function is enabled.
1: receive processor will enter running state.
0 R/W
0 --- reserved
W* = only write when the transmi t proc essor sto pped.
W* * = o n l y wr i te when the tran smi t and receive pro cessor bo th stop p ed .
W*** = onl y write when the rece ive proce sso r stoppe d.
CSR7(offset = 38h), IER - Interrupt Enable Register
Table 6. Control/Status reg ister description
Bit # Name Descrip tions Default Val RW Type
21/66
STE10/100
31~17 --- reserved
16 NIE Normal Interrupt Enable
1: enables all the normal interrupt bits (see bit 16 of CSR5) 0 R/W
15 AIE Abnormal Interrupt Enable
1: enables all the abnormal interrupt bits (see bit 15 of CSR5) 0 R/W
14 --- reserved
13 FBEIE Fatal Bus Error Interrupt Enable
1: this bit in conjunction with AIE (bit 15 of CSR7) will enable
the fatal bus error interrupt
0 R/W
12 --- Reserved
11 GPTIE General Purpose Timer Interrupt Enable
1: this bit in conjunction with AIE (bit 15 of CSR7) will enable
the general purpose timer expired interrupt.
0 R/W
10 --- Reserved
9 RWTIE Receive Watchdog Time-out Interrupt Enable
1: this bit in conjunction with AIE (bit 15 of CSR7) will enable
the receive watchdog time-out interrupt.
0 R/W
8 RSIE Receive Stopped Interrupt Enable
1: this bit in conjunction with AIE (bit 15 of CSR7) will enable
the receive stopped interrupt.
0 R/W
7 RUIE Receive Descriptor Unavailable Interrupt Enable
1: this bit in conjunction with AIE (bit 15 of CSR7) will enable
the receive descriptor unavailable interrupt.
0 R/W
6 RCIE Receive Completed Interrupt Enable
1: this bit in conjunction with NIE (bit 16 of CSR7) will enable
the receive completed interrupt.
0 R/W
5 TUIE Transmit Under-flow Interrupt Enable
1: this bit in conjunction with AIE (bit 15 of CSR7) will enable
the transmit under-flow interrupt.
0 R/W
4 --- Reserved
3 TJTTIE Transmit Jabber Timer Time-out Interrupt Enable
1: this bit in conjunction with AIE (bit 15 of CSR7) will enable
the transmit jabber timer time-out interrupt.
0 R/W
2 TDUIE Transmit Descriptor Unavailable Interrupt Enable
1: this bit in conjunction with NIE (bit 16 of CSR7) will enable
the transmit descriptor unavailable interrupt.
0 R/W
1 TPSIE Transmit Processor Stopped Interrupt Enable
1: this bit in conjunction with AIE (bit 15 of CSR7) will enable
the transmit processor stopped interrupt.
0 R/W
0 TCIE Transmit Completed Interrupt Enable
1: this bit in conjunction with NIE (bit 16 of CSR7) will enable
the transmit completed interrupt.
0 R/W
CSR8(offset = 40h), LPC - Lost packet counter
Table 6. Control/Status reg ister description
Bit # Name Descrip tions Default Val RW Type
STE10/100
22/66
31~17 --- Reserved
16 LPCO Lost Packet Counter Overflow
1: when lost packet counter overflow occurs. Cleared after
read.
0 RO/LH
15~0 LPC Lost Packet Counter
The counter is incremented whenev er a packet is discarded as
a result of no host receive descriptors being available. Cleared
after read.
0 RO/LH
CSR9(offset = 48h), SPR - Serial port register
31~15 --- Reserved
14 SRC Serial EEPROM Read Control
When set, enables read access from EEPROM, when SRS
(CSR9 bit 11) is also set.
0 R/W
13 SWC Serial EEPROM Write Control
When set, enables write access to EEPROM, when SRS
(CSR9 bit 11) is also set.
0 R/W
12 --- Reserved
11 SRS Serial EEPROM Select
When set, enables access to the serial EEPROM (see
description of CSR9 bit 14 and CSR9 bit 13)
0 R/W
10~4 --- Reserved
3 SDO Serial EEPROM data out
This bit serially shifts data from the EEPROM to the STE10/
100.
1RO
2 SDI Serial EEPROM data in
This bit serially shifts data from the STE10/100 to the
EEPROM.
1 R/W
1 SCLK Serial EEPROM clock
High/Low this bit to provide the clock signal for EEPROM. 1 R/W
0 SCS Serial EEPROM chip select
1: selects the serial EEPROM chip. 1 R/W
CSR11(offset = 58h), TMR -General-purpose Timer
31~17 --- Reserved
16 COM Continuous Operation Mode
1: sets the general-purpose timer in continuous operating
mode.
0 R/W
15~0 GTV General-purpose Timer Value
Sets the counter value. This is a count-down counter with a
cycle time of 204us.
0 R/W
CSR13(offset = 68h), WCSR –Wake-up Control/Status Register
31 --- Reserved
Table 6. Control/Status reg ister description
Bit # Name Descrip tions Default Val RW Type
23/66
STE10/100
30 CRCT CRC-16 Type
0: Initial contents = 0000h
1: Initial contents = FFFFh
0 R/W
29 WP1E Wake-up Pattern One Matched Enable. 0 R/W
28 WP2E Wake-up Pattern Two Matched Enable. 0 R/W
27 WP3E Wake-up Pattern Three Matched Enable. 0 R/W
26 WP4E Wake-up Pattern Four Matched Enable. 0 R/W
25 WP5E Wake-up Pattern Five Matched Enable. 0 R/W
24-18 --- Reserved
17 LinkOFF Link Off Detect Enable. The STE10/100 will set the LSC bit of
CSR13 after it has detected that link status has transitioned
from ON to OFF.
0 R/W
16 LinkON Link On Detect Enable. The STE10/100 will set the LSC bit of
CSR13 after it has detected that link status has transitioned
from OFF to ON.
0 R/W
15-11 --- Reserved
10 WFRE Wake-up Frame Received Enable. The STE10/100 will
include the “Wake-up Frame Received” event in its set of
wake-up events. If this bit is set, STE10/100 will assert
PMEST bit of PMR1 (CR49) after STE10/100 has received a
matched wake-up frame.
0 R/W
9 MPRE Magic Packet Received Enable. The STE10/100 will include
the “Magic Packet Received” event in its set of wake-up
events. If this bit is set, STE10/100 will assert PMEST bit of
PMR1 (CR49) after STE10/100 has received a Magic packet.
Default 1 if
PM & WOL
bits of CSR
18 are both
enabled.
R/W
8 LSCE Link Status Changed Enable. The STE10/100 will include the
“Link Status Changed” event in its set of wake-up events. If
this bit is set, STE10/100 will assert PMEST bit of PMR1 after
STE10/100 has detected a link status changed event.
0 R/W
7-3 --- Reserved
2 WFR Wake-up Frame Received,
1: Indicates STE10/100 has received a wake-up frame. It is
cleared by writing a 1 or upon power-up reset. It is not
affected by a hardware or software reset.
X R/W1C*
1 MPR Magic Packet Received,
1: Indicates STE10/100 has received a magic packet. It is
cleared by writing a 1 or upon power-up reset. It is not
affected by a hardware or software reset.
X R/W1C*
0 LSC Link Status Changed,
1: Indicates STE10/100 has detected a link status change
ev e nt. It is cleared by writing a 1 or upon power-up reset. It
is not affected by a hardware or software reset.
X R/W1C*
R/W1C * , Read On ly and Writ e o n e cleared.
Table 6. Control/Status reg ister description
Bit # Name Descrip tions Default Val RW Type
STE10/100
24/66
Table 6. Control/S tatus register description
CSR14(offset = 70h), WPDR –Wake-up Pattern Data Register
Offset 31 16 15 8 7 0
0000h Wake-up pattern 1 mask bits 31:0
0004h Wake-up pattern 1 mask bits 63:32
0008h Wake-up pattern 1 mask bits 95:64
000ch Wake-up pattern 1 mask bits 127:96
0010h CRC16 of pattern 1 Reserved Wake-up pattern 1 offset
0014h Wake-up pattern 2 mask bits 31:0
0018h Wake-up pattern 2 mask bits 63:32
001ch Wake-up pattern 2 mask bits 95:64
0020h Wake-up pattern 2 mask bits 127:96
0024h CRC16 of pattern 2 Reserved Wake-up pattern 2 offset
0028h Wake-up pattern 3 mask bits 31:0
002ch Wake-up pattern 3 mask bits 63:32
0030h Wake-up pattern 3 mask bits 95:64
0034h Wake-up pattern 3 mask bits 127:96
0038h CRC16 of pattern 3 Reserved Wake-up pattern 3 offset
003ch Wake-up pattern 4 mask bits 31:0
0040h Wake-up pattern 4 mask bits 63:32
0044h Wake-up pattern 4 mask bits 95:64
0048h Wake-up pattern 4 mask bits 127:96
004ch CRC16 of pattern 4 Reserved Wake-up pattern 4 offset
0050h Wake-up pattern 5 mask bits 31:0
0054h Wake-up pattern 5 mask bits 63:32
0058h Wake-up pattern 5 mask bits 95:64
005ch Wake-up pattern 5 mask bits 127:96
0060h CRC16 of pattern 5 Reserved Wake-up pattern 5 offset
1. Off set val ue is fr om 0-255 (8-bi t w i dth).
2. To load the whole wake-up f ram e fil tering i nform at io n, cons ecut i ve 25 l ong words wri te operation t o CS R14 should be done.
25/66
STE10/100
Table 6. Control/S tatus register description
Bit # Name Descrip tions Default Val RW Type
CSR15(offset = 78h), WTMR - Watchdog timer
31~6 --- Reserved
5 RWR Receive Watchdog Release. The time (in bit-times) from
sensing dropped carrier to releasing watchdog timer.
0: 24 bit-times
1: 48 bit-times
0 R/W
4 RWD Receive Watchdog Disable
0: If the received packet‘s length exceeds 2560 bytes, the
watchdog timer will expire.
1: disable the receive watchdog.
0 R/W
3 --- Reserved
2 J CLK Jabber clock
0: cut off transmission after 2.6 ms (100Mbps) or 26 ms
(10Mbps).
1: cut off transmission after 2560 byte-time.
0 R/W
1 NJ Non-Jabber
0: if jabber expires, re-enable transmit function after 42 ms
(100Mbps) or 420ms (10Mbps).
1: immediately re-enable the transmit function after jabber
expires.
0 R/W
0 J BD Jabber disable
1: disable transmit jabber function 0 R/W
CSR16(offset = 80h), ACSR5 - Assistant CSR5(Status register 2)
31 TEIS Transmit Early Interrupt status
Transmit early interrupt status is set to 1 when TEIE (bit 31 of
CSR17 set) is enabled and the transmitted packet is moved
from descriptors to the TX-FIFO buffer. This bit is cleared by
writing a 1.
0 RO/LH*
30 REIS Receive Early Interrupt Status.
Receive early interrupt status is set to 1 when REIE (CSR17
bit 30) is enabled and the received packet has filled up its first
receive descriptor. This bit is cleared by writing a 1.
0 RO/LH*
29 XIS Transceiver (XCVR) Interrupt Status. Formed by the logical
OR of XR8 bits 6~0. 0 RO/LH*
28 TDIS Transmit Deferred Interrupt Status. 0 RO/LH*
27 --- Reserved
26 PFR PAUSE Frame Received Interrupt Status
1: indicates receipt of a PAUSE frame while the PAUSE
function is enabled.
0 RO/LH*
25~ 23 BET Bus Error Type. This field is valid only when FBE (CSR5 bit
13, fatal bus error) is set. There is no interrupt generated by
this field.
000: parity error, 001: master abort, 010: target abort
011, 1xx: reserved
000 RO
STE10/100
26/66
22~ 20 TS Transmit State. Reports the current transmission state only,
no interrupt will be generated.
000: stop
001: read descriptor
010: transmitting
011: FIFO fill, read the data from memory and put into FIFO
100: reserved
101: reserved
110: suspended, unavailable transmit descriptor or FIFO
overflow
111: write descriptor
000 RO
19~17 RS Receive State. Reports current receive state only, no interrupt
will be generated.
000: stop
001: read descriptor
010: check this packet and pre-fetch next descriptor
011: wait for receiving data
100: suspended
101: write descriptor
110: flush the current FIFO
111: FIFO drain, move data from receiving FIFO into memory
000 RO
16 ANISS Added normal interrupt status summary.
1: whenever any of the added normal interrupts occur. 0 RO/LH*
15 AAISS Ad ded Abno r mal Interr upt Statu s Summary.
1: whenever any of the added abnormal interrupts occur. 0 RO/LH*
14~0 These bits are the same as the status register of CSR5, and
are accessible through either CSR5 or CSR16.
LH* = High Latching and clea red by writing 1.
CSR17(offset = 84h), ACSR7- Assistant CSR7(Interrupt enable register 2)
31 TEIE Transmit Early Interrupt Enable 0 R/W
30 REIE Receive Early Interrupt Enable 0 R/W
29 XIE Transceiver (XCVR) Interrupt Enable 0 R/W
28 TDIE Transmit Deferred Interrupt Enable 0 R/W
27 --- Reserved
26 PFRIE PAUSE Frame Received Interrupt Enable 0 R/W
25~17 --- Reserved
16 ANISE Added Normal Interrupt Summary Enable.
1: adds the interrupts of bits 30 and 31 of ACSR7 (CSR17) to
the normal interrupt summary (bit 16 of CSR5).
0 R/W
15 AAIE Ad ded Abno rm al Interr upt Summ ar y Enable.
1: adds the interrupt of bits 27, 28, and 29 of ACSR7 (CSR17)
to the abnormal interrupt summary (bit 16 of CSR5).
0 R/W
14~0 These bits are the same as the interrupt enable register of
CSR7, and are accessible through either CSR7 or CSR16.
Table 6. Control/S tatus register description
Bit # Name Descrip tions Default Val RW Type
27/66
STE10/100
CSR18(offset = 88h), CR - Command Register, bit31 to bit16 automatically recall from EEPROM
31 D3CS D3cold power state wake up Support. If this bit is reset then
bit 31 of PMR0 will be reset to ‘0’. If this bit is asserted and an
auxiliary power source is detected then bit 31 of PMR0 will be
set to ‘1’.
0
from
EEPROM
R/W
30-28 AUXCL Aux. Current Load. These three bits report the maximum
3.3Vaux current requirements for STE10/100 chip. If bit 31 of
PMR0 is ‘1’, the default value is 111b, which means the
STE10/100 need 375 mA to support remote wake-up in
D3cold power state. Otherwise, the default value is 000b,
which means the STE10/100 does not support remote wake-
up from D3cold power state.
000b
from
EEPROM
R/W
27-24 --- Reserved
23 4LEDmode
_on This bit is used to control the LED mode selection.
If this bit is reset, mode 1 (3 LEDs) is selected; the LEDs
definition is:
100/10 speed
Link/Activity
Full Duplex/Collision
If this bit is set, mode 2 (4 LEDs) is selected; the LEDs
definition is:
100 Link
10 Link
Activity
Full Duplex/Collision
0
from
EEPROM
R/W
22, 21 RFS Receive FIFO size control
11: 1K bytes
10: 2K bytes
01,00: reserved
10
from
EEPROM
R/W
20 --- Reserved
19 PM Power Management. Enables the STE10/100 Power
Management abilities. When this bit is set into “0” the STE10/
100 will set the Cap_Ptr register to zero, indicating no PCI
compliant power management capabilities. The value of this
bit will be mapped to NC (CR1 bit 20). In PCI Power
Management mode, the Wake Up Frames include “Magic
Packet”, “Unicast”, and “Muliticast”.
X
from
EEPROM
RO
18 WOL W ake on LAN mode enable. When this bit is set to ‘1’, then the
STE10/100 enters Wake On LAN mode and enters the sleep
state.
Once the STE10/100 enters the sleep state, it remains there
until: the Wake Up event occurs, the WOL bit is cleared, or a
reset (software or hardware) happens.
In Wake On LAN mode the Wake-Up frame is “Magic Packet”
only.
X
from
EEPROM
R/W
17~7 --- Reserved
6 RWP Reset Wake-up Pattern Data Register Pointer 0 R/W
Table 6. Control/S tatus register description
Bit # Name Descrip tions Default Val RW Type
STE10/100
28/66
5 PAUSE Disable or enable the PAUSE function for flow control. The
default value of PAUSE is determined by the result of Auto-
Negotiation. The driver software can overwrite this bit to
enable or disable it after the Auto-Negotiation has completed.
0: PAUSE function is disabled.
1: PAUSE function is enabled
Depends
on the
result of
Auto-
Negotiation
R/W
4 RTE Receive Threshold Enable.
1: the receive FIFO threshold is enabled.
0: disable the receive FIFO threshold selection in DRT (bits
3~2), and the receive threshold is set to the default 64 bytes.
0 R/W
3~2 DRT Drain Receive Threshold
00: 32 bytes (8 DW)
01: 64 bytes (16 DW)
10: store-and -forward
11: reserved
01 R/W
1 SINT Software interrupt. 0 R/W
0 ATUR 1: enable automatically transmit-underrun recovery. 0 R/W
CSR19(offset = 8ch) - PCIC, PCI bus performance counter
31~16 CLKCNT The number of PCI clocks from read request asserted to
access completed. This PCI clock count is accumulated for all
the read command cycles from the last CSR19 read to the
current CSR1 9 read.
0 RO*
15~8 --- reserved
7~0 DWCNT The number of double words accessed by the last bus master.
This double word count is accumulated for all bus master data
transactions from the last CSR19 read to the current CSR19
read.
0 RO*
RO* = Read onl y and cleared by reading.
CSR20 (offset = 90h) - PMCSR, Po wer Management Command and Status (The same register value mapping to
CR49-PMR1.)
31~16 --- reserved
15 PMES PME_Status. This bit is set whenever the STE10/100 detects
a wake-up event, regardless of the state of the PME-En bit.
Writing a “1” to this bit will clear it, causing the STE10/100 to
deassert PME# (if so enabled). Writing a “0” has no effect.
0RO
14,13 DSCAL Data_Scale. Indicates the scaling factor to be used when
interpreting the value of the Data register. This field is
required for any function that implements the Data register.
The STE10/100 does not support Data register and
Data_Scale.
00b RO
12~9 DSEL Data_Select. This four bit field is used to select which data is
to be reported through the Data register and Data_Scale field.
This field is required for any function that implements the Data
register.
The STE10/100 does not support Data_select.
0000b RO
Table 6. Control/S tatus register description
Bit # Name Descrip tions Default Val RW Type
29/66
STE10/100
8 PME_En PME_En. When set, enables the STE10/100 to assert PME#.
When cleared, disables the PME# assertion. 0RO
7~2 --- reserved. 000000b RO
1,0 PWRS PowerState, This two-bit field is used both to determine the
current power state of the STE10/100 and to set the STE10/
100 into a new power state. The definition of this field is given
below.
00b - D0
01b - D1
10b - D2
11b - D3hot
If software attempts to write an unsupported state to this field,
the write operation will complete normally on the bus, but the
data is discarded and no state change occurs.
00b RO
CSR23(offset = 9ch) - TXBR, transmit burst count / time-out
31~21 --- reserved
20~16 TBCNT Transmit Burst Count
Specifies the number of consecutive successful transmit burst
writes to complete before the transmit completed interrupt will
be generated.
0 R/W
11~0 TTO Transmit Time-Out = (deferred time + back-off time).
When TDIE (ACSR7 bit 28) is set, the timer is decreased in
increments of 2.56us (@100M) or 25.6us (@10M). If the timer
expires before another packet transmit begins, then the TDIE
interrupt will be generated.
0 R/W
CSR24(offset = a0h) - FROM, Flash ROM(also the boot ROM) port
31 bra16_on This bit is only valid when 4 LEDmode_on (CSR18 bit 23) is
set. In this case, when bra16_on is set, pin 87 functions as
brA16; otherwise it functions as LED pin – fd/col.
1 R/W
30~28 --- reserved
27 REN Read Enable. Clear if read data is ready in DATA, bit7-0 of
FROM. 0 R/W
26 WEN Write Enable. Cleared if write completed. 0 R/W
25 --- reserved
24~8 ADDR Flash ROM address 0 R/W
7~0 DATA Read/Write data of flash ROM 0 R/W
CSR25(offset = a4h) - PAR0, physical address register 0, automatically recalled from EEPROM
31~24 PAB3 physical address byte 3 From
EEPROM R/W
23~16 PAB2 physical address byte 2 From
EEPROM R/W
15~8 PAB1 physical address byte 1 From
EEPROM R/W
Table 6. Control/S tatus register description
Bit # Name Descrip tions Default Val RW Type
STE10/100
30/66
7~0 PAB0 physical address byte 0 From
EEPROM R/W
CSR26(offset = a8h) - PAR1, physical address register 1, automatically recalled from EEPROM
31~24 --- reserved
23~16 --- reserved
15~8 PAB5 physical address byte 5 From
EEPROM R/W
7~0 PAB4 physical address byte 4 From
EEPROM R/W
For exampl e, ph ysical a dd r ess = 00-00-e8-11-22-33
PAR0= 11 e8 00 00
PAR1= XX XX 33 22
PAR0 and PAR1 are readable, but can be writt en only if the receive sta te is in stopped (CSR5 bits 19-17=00 0) .
CSR27(offset = ach) - MAR0, multicast address register 0
31~24 MAB3 multicast address byte 3 (hash table 31:24) 00h R/W
23~16 MAB2 multicast address byte 2 (hash table 23:16) 00h R/W
15~8 MAB1 multicast address byte 1 (hash table 15:8) 00h R/W
7~0 MAB0 multicast address byte 0 (hash table 7:0) 00h R/W
CSR28(offset = b0h) - MAR1, multicast address register 1
31~24 MAB7 multicast address byte 7 (hash table 63:56) 00h R/W
23~16 MAB6 multicast address byte 6 (hash table 55:48) 00h R/W
15~8 MAB5 multicast address byte 5 (hash table 47:40) 00h R/W
7~0 MAB4 multicast address byte 4 (hash table 39:32) 00h R/W
MA R0 an d M AR1 are read ab le, but can b e written only if the receive state is in sto p ped(CSR5 bit 19-17=000).
Table 6. Control/S tatus register description
Bit # Name Descrip tions Default Val RW Type
31/66
STE10/100
5.3 Trans ceiver(X CV R) Registers
There are 11 16-bit registers supporting the transceiver portion of STE10/100, including 7 basic registers de-
fined according to clause 22 “Reconciliation Sublayer and Media Independent Interface” and clause 28 “Physi-
cal Layer link signal ing for 10 Mb/s and 100 Mb/s Auto-Negotiation on twisted pair” of the IEEE802.3u standard.
In addition, 4 special registers are provided for advanced chip control and status.
Note: 1. Since only Double Word access is supported for Register R/W in the STE10/100, the higher word(bit 31~16) of the XCVR registers
(XR0~X R10) shoul d be i gnored.
Table 7. Transceiver regi sters list
Offset from
b ase addres s
of CSR Reg. Index Name Register Descriptions
b4h XR0 XC R XCVR Control Register
b8h XR1 XS R XCVR Statu s Register
bch XR2 PID1 PHY Identifier 1
c0h XR3 PID2 PHY Identifier 2
c4h XR4 ANA Auto-Negotiation Advertisement Register
c8h XR5 ANLPA Auto-Negotiation Link Partner Ability Register
cch XR6 ANE Auto-Negotiation Expansion Register
d0h XR7 XMC XCVR Mode Control Register
d4h XR8 XCIIS XCVR Configuration Information and Interrupt Status Register
d8h XR9 XIE XCVR Interrupt Enable Register
dch XR10 100CTR 100BASE-TX PHY Control/Status Register
Table 8. Transcei ver registers Descrip tions
Bit # Name Descrip tions Default Val RW Type
XR0(offset = b4h) - XCR, XCVR Control Register. The default value is chosen as listed below.
15 XRST Transceiver Reset control.
1: reset transceiver . This bit will be cleared by STE10/100 after
transceiver reset has completed.
0 R/W
14 XLBEN Transceiver loop-back mode select.
1: transceiver loop-back mode is selected. OM (CSR6 bits
11,10) of must contain 00.
0 R/W
13 SPSEL Network Speed select. This bit will be ignored if Auto-
Negotiation is enabled (ANEN, XR0 bit 12).
1:100Mbps is selected.
0:10Mbps is selected.
1 R/W
12 ANEN Auto-Negotiation ability control.
1: Auto-Negotiation function is enabled.
0: Auto-Negotiation is disabled.
1 R/W
STE10/100
32/66
11 PDEN Power down mode control.
1: transceiver power-down mode is selected. In this mode, the
STE10/100 transceivers are turned off.
0 R/W
10 --- reserved 0 RO
9 RSAN Re-Start Auto-Negotiation process control.
1: Auto-negotiation process will be restarted. This bit will be
cleared by STE10/100 after the Auto-negotiation has
restarted.
0 R/W
8 DPSEL Full/Half duplex mode select.
1: full duplex mode is selected. This bit will be ignored if Auto-
Negotiation is enabled (ANEN, XR0 bit 12).
0 R/W
7 COLEN Collision test control.
1: collision test is enabled. 0 R/W
6~0 --- reserved 0 RO
R/W = Read/Write able. RO = Read Only.
XR1(offset = b8h) - XSR, XCVR Status Register. All the bits of this register are read only.
15 T4 100BASE-T4 ability.
Always 0, since STE10/100 has no T4 ability. 0RO
14 TXFD 100BASE-TX full duplex ability.
Always 1, since STE10/100 has 100BASE-TX full duplex
ability.
1RO
13 TXHD 100BASE-TX half duplex ability.
Always 1, since STE10/100 has 100BASE-TX half duplex
ability.
1RO
12 10FD 10BASE-T full duplex ability.
Always 1, since STE10/100 has 10Base-T full duplex ability. 1RO
11 10HD 10BASE-T half duplex ability.
Always 1, since STE10/100 has 10Base-T half duplex ability. 1RO
10~6 --- reserved 0 RO
5 ANC Auto-Negotiation Completed.
0: Auto-Negotiation process incomplete.
1: Auto-Negotiation process complete.
0RO
4 RF Result of remote fault detection.
0: no remote fault condition detected.
1: remote fault condition detected.
0 RO/LH*
3 AN Auto-Negotiation ability.
Always 1, since STE10/100 has Auto-negotiation ability. 1RO
2 LINK Link status.
0: a link failure condition occurred. Readin clears this bit.
1: valid link established.
0 RO/LL*
1 JAB Jabber detec tion.
1: jabber condition detected (10Base-T only). 0 RO/LH*
Table 8. Transcei ver registers Descrip tions
Bit # Name Descrip tions Default Val RW Type
33/66
STE10/100
0 EXT Extended register support.
Always 1, since STE10/100 supports extended register 1RO
LL* = Latching Low and clear by read. LH* = Latching High and clea r by read .
XR2(offset = bch) - PID1, PHY identifier 1
15~0 PHYID1 Part one of PHY Identifier.
Assigned to the 3rd to 18th bits of the Organizationally Unique
Identifier.
0382h RO
XR3(offset = c0h) - PID2, PHY identifier 2
15~10 PHYID2 Part two of PHY Identifier.
Assigned to the 19th to 24th bits of the Organizationally Unique
Identifier (OUI).
010010b RO
9~4 MODEL Model number of STE10/100.
6-bit manufacturer’s model number. 000001b RO
3~0 REV Revision number of STE10/100.
4-bits manufacturer’s revision number. 0000b RO
XR4(offset = c4h) - ANA, Auto-Negotiation Advertisement
15 NXTPG Next Page ability.
Always 0; STE10/100 does not provide next page ability. 0RO
14 --- reserved
13 RF Remote Fault function.
1: remote fault function present 0 R/W
12,11 --- reserved
10 FC Flow Control function Ability.
1: supports PAUSE operation of flow control for full duplex link. 1 R/W
9 T4 100BASE-T4 Ability.
Always 0; STE10/100 does not provide 100BASE-T4 ability. 0RO
8 TXF 100BASE-TX Full duplex Ability.
1: 100Base-TX full duplex ability supported 1 R/W
7 TXH 100BASE-TX Half duplex Ability.
1: 100Base-TX ability supported. 1 R/W
6 10F 10BASE-T Full duplex Ability.
1: 10Base-T full duplex ability supported. 1 R/W
5 10H 10BASE-T Half duplex Ability.
1: 10Base-T ability supported. 1 R/W
4~0 SF Select field. Default 00001=IEEE 802.3 00001 RO
XR5(offset = c8h) - ANLP, Auto-Negotiation Link Partner ability
15 LPNP Link partner Next Page ability.
0: link partner without next page ability.
1: link partner with next page ability.
0RO
Table 8. Transcei ver registers Descrip tions
Bit # Name Descrip tions Default Val RW Type
STE10/100
34/66
14 LPACK Received Link Partner Acknowledge.
0: link code word not yet received.
1: link partner successfully received STE10/100’s link code
word.
0RO
13 LPRF Link Partner’s Remote fault status.
0: no remote fault detected.
1: remote fault detected.
0RO
12,11 --- reserved 0 RO
10 LPFC Link Partner’s Flow control ability.
0: link partner without PAUSE function ability.
1, link partner with PAUSE function ability for full duplex link.
0RO
9 LPT4 Link Partner’s 100BASE-T4 ability.
0: link partner without 100BASE-T4 ability.
1: link partner with 100BASE-T4 ability.
0RO
8 LPTXF Link Partner’s 100BASE-TX Full duplex ability.
0: link partner without 100BASE-TX full duplex ability.
1: link partner with 100BASE-TX full duplex ability.
0RO
7 LPTXH Link Partner’s 100BASE-TX Half duplex ability.
0: link partner without 100BASE-TX.
1: link partner with 100BASE-TX ability.
0RO
6 LP10F Link Partner’s 10BASE-T Full Duplex ability.
0: link partner without 10BASE-T full duplex ability.
1: link partner with 10BASE-T full duplex ability.
0RO
5 LP10H Link Partner’s 10BASE-T Half Duplex ability.
0: link partner without 10BASE-T ability.
1: link partner with 10BASE-T ability.
0RO
4~0 LPSF Link partner select field. Default 00001=IEEE 802.3. 00001 RO
XR6(offset = cch) - ANE, Auto-Negotiation expansion
15~5 --- reserved 0 RO
4 PDF Parallel detection fault.
0: no fault detected.
1: a fault detected via parallel detection function.
0 RO/LH*
3 LPNP Link Partner’s Next Page ability.
0: link partner without next page ability.
1: link partner with next page ability.
0RO
2 NP STE10/100’s next Page ability.
Always 0; STE10/100 does not support next page ability. 0RO
1 PR Page Received.
0: no new page has been received.
1: a new page has been received.
0 RO/LH*
0 LPAN Link Partner Auto-Negotiation ability.
0: link partner has no Auto-Negotiation ability.
1: link partner has Auto-Negotiation ability.
0RO
LH = High Latching and clear ed by readi ng.
Table 8. Transcei ver registers Descrip tions
Bit # Name Descrip tions Default Val RW Type
35/66
STE10/100
XR7(offset = d0h) - XMC, XCVR Mode control
15~12 --- reserved 0 RO
11 LD Long Distance mode of 10BASE-T.
0: normal squelch level.
1: reduced 10Base-T squelch level for extended cable length.
0 R/W
10~0 --- reserved 0 RO
XR8(offset = d4h) - XCIIS, XCVR Configuration information and Interrupt Status
15~10 ---- reserved 0 RO
9 SP EED Speed configuration setting.
0: the speed is 10Mb/s.
1: the speed is 100Mb/s.
0RO
8 DUPLEX Duplex configuration setting.
0: the duplex mode is half.
1: the duplex mode is full.
0RO
7 PAUSE PAUSE function configuration setting for flow control.
0: PAUSE function is disabled.
1: PAUSE function is enabled
0RO
6 ANC Auto-Negotiation Completed Interrupt.
0: Auto-Negotiation has not completed yet.
1: Auto-Negotiation has completed.
0 RO/LH*
5 RFD Remote Fault Detected Interrupt.
0: there is no remote fault detected.
1: remote fault is detected.
0 RO/LH*
4 LS Link Fail Interrupt.
0: link test status is up.
1: link is down.
0 RO/LH*
3 ANAR Auto-Negotiation Acknowledge Received Interrupt.
0: there is no link code word received.
1: link code word is receive from link partner.
0 RO/LH*
2 PDF Parallel Detection Fault Interrupt.
0: there is no parallel detection fault.
1: parallel detection is fault.
0 RO/LH*
1 ANPR Auto-Negotiation Page Received Interrupt.
0: there is no Auto-Negotiation page received.
1: auto-negotiation page is received.
0 RO/LH*
0 REF Receive Error full Interrupt.
0: the receive error number is less than 64.
1: 64 error packets is received.
0 RO/LH*
LH = High Latching and clear ed by readi ng.
XR9(offset = d8h) - XIE, XCVR Interrupt Enable Register
15~7 --- reserved
Table 8. Transcei ver registers Descrip tions
Bit # Name Descrip tions Default Val RW Type
STE10/100
36/66
6 ANCE Auto-Negotiation Completed interrupt Enable.
0: disable Auto-Negotiation completed interrupt.
1: enable auto-negotiation complete interrupt.
0 R/W
5 RFE Remote Fault detected interrupt Enable.
0: disable remote fault detection interrupt.
1: enable remote fault detection interrupt.
0 R/W
4 LDE Link Down interrupt Enable.
0: disable link fail interrupt.
1: enable link fail interrupt.
0 R/W
3 ANAE Auto-Negotiation Acknowledge interrupt Enable.
0: disable link partner acknowledge interrupt
1: enable link partner acknowledge interrupt.
0 R/W
2 PDFE Parallel Detection Fault interrupt Enable.
0: disable fault parallel detection interrupt.
1: enable fault parallel detection interrupt.
0 R/W
1 ANPE Auto-Negotiation Page Received interrupt Enable.
0: disable Auto-Negotiation page received interrupt.
1: enable Auto-Negotiation page received interrupt.
0 R/W
0 REFE RX_ERR full interrupt Enable.
0: disable rx_err full interrupt.
1: enable rx_err interrupt.
0 R/W
XR10(offset = dch) - 100CTR, 100BASE-TX Control Register
15,14 --- reserved
13 DISRER Disable the RX_ERR counter.
0: the receive error counter - RX_ERR is enabled.
1: the receive error counter - RX_ERR is disabled.
0 R/W
12 ANC Auto-Negotiation completed. This bit is the same as bit 5 of
XR1.
0: the Auto-Negotiation process has not completed yet.
1: the Auto-Negotiation process has completed.
0RO
11 RXVPP Select peak to peak voltage of receive.
0: receive voltage peak to peak 1.0 VPP
1: receive voltage peak to peak 1.4 VPP.
0 R/W
10 --- reserved
9 ENRLB Enable remote loop-back function.
1: enable remote loop-back (CSR6 bits 11 and 10 must be 00). 0 R/W
8 ENDCR Enable DC restoration.
0: disable DC restoration.
1: enable DC restoration.
1 R/W
7 ENRZI Enable the conversions between NRZ and NRZI.
0: disable the data conversion between NRZ and NRZI.
1: enable the data conversion of NRZI to NRZ in receiving and
NRZ to NRZI in transmitting.
1 R/W
6 --- reserved.
Table 8. Transcei ver registers Descrip tions
Bit # Name Descrip tions Default Val RW Type
37/66
STE10/100
5.4 Des criptors and Buffer Manag ement
The STE10/100 provides receive and transmit descriptors for packet buffering and management.
5.4.1 Receive descript or
Table 9. Receive Descriptor Table
31 0
No te : 1. Descri ptor s and receive buffers addresse s m ust be l ongword aligned
5 ISO TX Transmit Isolation. When 1, isolate from MII and tx+/-. This bit
must be 0 for normal operation 0 R/W
4~2 CMODE Reports current transceiver operating mode.
000: in auto-negotiation
001: 10Base-T half duplex
010: 100Base-TX half duplex
011: reserved
100: reserved
101: 10Base-T full duplex
110: 100Base-TX full duplex
111: isolation, auto-negotiation disable
000 RO
1 DISMLT Disable MLT3.
0: the MLT3 encoder and decoder are enabled.
1: the MLT3 encoder and decoder are bypassed.
0 R/W
0 DISCRM Disable Scramble.
0: the scrambler and de-scrambler is enabled.
1: the scrambler and de-scrambler are disabled.
0 R/W
RDES0 Own Status
RDES1 --- Control Buffer2 byte-count Buffer1 byte-count
RDSE2 Buffer1 address (DW boundary)
RDSE3 Buffer2 address (DW boundary
Table 8. Transcei ver registers Descrip tions
Bit # Name Descrip tions Default Val RW Type
STE10/100
38/66
Table 10. Receive Descriptor Descriptions
Bit# Name Descriptions
RDES0
31 OWN Own bit
1: indicates that newly received data can be put into this descriptor
0: Host has not yet processed the received data currently in this descriptor.
30-16 FL Frame length, including CRC. This field is valid only in a frame’s last descriptor.
15 ES Error summary. Logical OR of the following bits:
0: overflow
1: CRC error
6: late collision
7: frame too long
11: runt packet
14: descriptor error
This field is valid only in a frame’s last descriptor.
14 DE Descriptor error. This bit is valid only in a frame’s last descriptor.
1: the current valid descriptor is unable to contain the packet being currently received. The
packet is truncated.
13-12 DT Data type.
00: nor ma l
01: MAC loop-b ack
10: Transceiver loop-back
11: remote loop-back
These bits are valid only in a frame’s last descriptor.
11 RF Runt frame (packet length < 64 bytes). This bit is valid only in a frame’s last descriptor.
10 MF Multicast frame. This bit is valid only in a frame’s last descriptor.
9 FS First descriptor.
8 LS Last descriptor.
7 TL Packet Too Long (packet length > 1518 bytes). This bit is valid only in a frame’s last descriptor.
6 CS Late collision. Set when collision is active after 64 bytes. This bit is valid only in a frame’s last
descriptor
5 FT Frame type. This bit is valid only in a frame’s last descriptor.
0: 802.3 type
1: Ethernet type
4 RW Receive watchdog (refer to CSR15, bit 4). This bit is valid only in a frame’s last descriptor.
3 reserved Default = 0
2 DB Dribble bit. This bit is valid only in a frame’s last descriptor
1: Packet length is not integer multiple of 8-bit.
1 CE 1: CRC error. This bit is valid only in a frame’s last descriptor
0 OF 1: Overflow. This bit is valid only in a frame’s last descriptor
RDES1
31~26 --- reserved
25 RER Receive end of ring. Indicates this descriptor is last, return to base address of descriptor
39/66
STE10/100
5.4.2 Transmit Descriptor
Table 11. Transmit Descr iptor Table
31 0
Note: 1. Descriptor addresses must be longword alignment
24 RCH Second address chain
Used for chain structure, indicating the buffer 2 address is the next descriptor address. Ring
mode takes precedence over chained mode
23~22 --- reserved
21~11 RBS2 Buffer 2 size (DW boundary)
10~ 0 RBS1 Buffer 1 size (DW boundary)
RDES2
31~0 RBA1 Receive Buffer Address 1. This buffer address should be double word aligned.
RDES3
31~0 RBA2 Receive Buffer Address 2. This buffer address should be double word aligned.
TDES0 Own Status
TDES1 Control Buffer2 byte-count Buffer1 byte-count
TDSE2 Buffer1 address
TDSE3 Buffer2 address
Table 12. Transmit Descr iptor Descr iptions
Bit# Name Descriptions
TDSE0
31 OWN Own bit
1: Indicates this descriptor is ready to transmit
0: No transmit data in this descriptor.
30-24 --- Reserved
23-22 UR Under-run count
21-16 --- Reserved
15 ES Error summary. Logical OR of the following bits:
1: under-run error
8: excessive collision
9: late collision
10: no carrier
11: loss carrier
14: jabber time-out
14 TO Transmit jabber time-out
Table 10. Receive Descriptor Descriptions
Bit# Name Descriptions
STE10/100
40/66
13-12 ----- Reserved
11 LO Loss of carrier
10 NC No carrier
9 LC Late collision
8 E C E xces sive collision
7 HF Heartbeat fail
6-3 CC Collision count
2 ----- Reserved
1 UF Under-run error
0 DE Deferred
TDES1
31 IC Interrupt completed
30 LS Last descriptor
29 FS First descriptor
28,27 --- Reserved
26 AC Disable add CRC function
25 TER End of Ring
24 TCH 2nd address chain. Indicates that the buffer 2 address is the next descriptor address
23 DPD Disable padding function
22 --- Reserved
21-11 TBS2 Buffer 2 size
10-0 TBS1 Buffer 1 size
TDES2
31~0 BA1 Buffer Address 1. No alignment limitations imposed on the transmission buffer address.
TDES3
31~0 BA2 Buffer Address 2. No alignment limitations imposed on the transmission buffer address.
Table 12. Transmit Descr iptor Descr iptions
Bit# Name Descriptions
41/66
STE10/100
6.0 FUNCTIONAL DESCRIPTIONS
6. 1 Initialization Flow
Figure 4. Initialization Flow of STE10/100
Search NIC
Get base IO address
Get IRQ value
Reset MAC (CSR0)
Reset PHY (XR0)
Need set
media type?
Read EEPROM from CSR9
Set Physical adress (CSR25, 26)
Need set
Multicast?
(Force Media)
Program the media
type to XR0
Yes
No
A
Set Multicast address
table (CSR27, 28)
No
Yes
Prepare Transmit descriptor and buffer
Prepare Receive descriptor and buffer
Install NIC ISR function
Ope n NIC inter rup t
En ab le T x & Rx f unctio n s
END
STE10/100
42/66
6.2 Network Packet Buffer Management
6.2.1 Descrip tor Stru ctur e Type s
During normal network transmit operations, the STE10/100 transfers the data packets from transmit buffers in
the host’s m emory to the STE10/100’s tr ansmit FIFO. For r eceive operations, the STE10/100 transfers the data
packet from its receive FIFO to receive buffers in the host’s memory. The STE10/100 makes use of descr iptors,
data structures which are built in host memory and contain pointers to the transmit and receive buffers and main-
tain packet and frame parameters, status, and other information vital to controlling network operation.
There are two types of structures employed to group descriptors, the
Ring
and
the
Chain
, both supported by
the STE10/100 and shown below. The sel ection of st ructure type is controlled by RCH (RDES1 bit 24) and TCH
(TDES1 bit 24).
The transmit and recei ve buffers r eside in th e host’s memory . Any buffer can contai n either a complete or p artial
packet. A buffer may not contain more than one packet.
■Ring structure: There are two buffers per descriptor i n the ring structure. Support receive early interrupt .
Figure 5. Ring structure of frame buffer
own
D ata Bu ffe r
Length 1
Data
D ata L en gth 2
Buffer1 pointer
Buffer2 pointer
Length 2 Length 1
Descriptor
.
.
.
.
.
.
.
Descriptor Pointer
CSR3 or CSR4
End of Ring
43/66
STE10/100
■Chain structure: There is only one buffer per descriptor in chain structure.
Figure 6. Chain structure of frame buffer
own
Data Buffer
Length 1
Data
Data Length 2
Buffer1 pointer
Next pointer
Length 1
---
own
Buffer1 pointer
Next pointer
Length 2
---
own
Buffer1 pointer
Next pointer
Length 3
---
Data Length 3
Descriptor
.
.
.
.
.
.
Descriptor Pointer
CSR3 or CSR4
STE10/100
44/66
6.2.2 Descrip tor Man agem ent
OWN bit = 1, ready for network side access
OWN bit = 0, ready for host side access
■Transmit Descriptors
Figure 7. Transmit descriptor management
Buffe r 1 poi nter
Buffe r 2 poi nter
Descriptor Ring
Data Buffer
data
data
end of ring
Length 1Length 2
0
1
1
1
0
0
p
acket1
p
acket1
p
acket2
next packet to be transmitted
own bit = 1,
Packet 1 and packet 2
are ready to transmit
empty desc r ip t or pointer
•
•
•
45/66
STE10/100
■Receive Descriptors
Figure 8. Receive des crip tor man agem e nt
Data
ff
end of ring
0
1
1
1
0
0
Packet 1
Packet 2
own bit=1,
next descriptor ready
for incoming packet
filled descriptor pointer
Packet 2
•
•
•
STE10/100
46/66
6.3 Transmit Schem e an d Transm i t Early Inte rrup t
6.3.1 T ransmit flow
Figure 9. The flow of packet transmit is shown as below.
Own = 1
Initialize descriptor
Pl ace data in host memory
Set Own bit to 1
Writ e Tx demand poll command
Transfer data to Tx FIFO
Exit STE10/100
chec ks descriptor
Deferring OR data less
than Tx threshold?
Transmit data
across line
Collision
occurred?
Wr ite des c riptor
Generate interrupt
Back-off
Own = 0
47/66
STE10/100
6.3.2 Transmit pre-fetch data flow
■Transmit FIFO size=2K-byte
■two packets in the FIFO at the same time
■meet the transmit min. back-to-back
Fi gure 10 . Trans m i t dat a flow of pre-fe t ch da t a
6.3.3 Tra nsm i t early int erru pt S cheme
Figure 11. Transm it norm al interru pt and early interr upt comp ari son
place the 1st packet data into host memory
issue transmit demand
FIFO-to-host memory operation (1st packet)
time
Transmit enable
place the 2nd packet data into host memory check the next
packet
check point
FIFO-to-host memory operation (2nd packet)
transm it threshold
place the 3rd packet data into host memory
1st packet is
transmitted, check
the 3rd packet
FIFO-to-host memory operation (3rd packet)
IFG
check point
1st packet 2nd packe t
: handled by driver : h andled b y STE10/1 00
Host to TX-FIFO Memory
Operation
Transm it da ta from FIFO to Media
Normal In terru pt a fter Transmit
Completed
Driver return b uffer to upper layer
Early Interrupt after Host to TX -
FIFO Operation Completed
Driver return b uffer to upper layer
The saved time when transm it
early int errupt is implem en ted
time
: handled by STE10/100
: handled by driver
STE10/100
48/66
6.4 Rec eive scheme and Recei ve earl y interrupt scheme
The following figure shows the difference of timing without early interrupt and with early interrupt.
Figure 12. Receive da ta flow (without early interrup t and with early interrup t)
Figure 13. Detailed Receive Ear ly interrupt flow
: with early int errupt
: without early interrupt
incoming packet
receive FIFO operation
FIFO-to-hos t memor y operat ion
interrupt
driver read header
higher layer process
driver read the rest data
time
receive early interrupt
dri ver read hea der(early)
hig her l ayer process( early)
dri ver read the rest data
finish time
finish time
FI FO-to- host memory
i
time
receive early
driver read
higher laye r
driver read the rest finish
i
1st
descriptor
full 2nd descriptor
The size of 1st
des c r iptor is
pro gramme d as the
he ader s ize i n
advance
issue 2nd
interrupt at end
of p acket
49/66
STE10/100
6.5 Network Operation
6.5.1 MAC Operation
The MAC (Media Access Control) portion of STE10/100 incorporates the essential protocol requirements for op-
erating as an IEEE802.3 and Ethernet compliant node.
■Format
*No te : I f padding i s disabled (T DES1 bi t 23), the dat a fiel d m ay be shorter than 46 by tes.
■Transmit Data Encapsulation
The differences between transmit data encapsulation and a MAC frame while operating in 100BASE-
TX mode are listed as follows:
1. The first byte of the preamble is replaced by the JK code according to IEE802.3u, clause 24.
2. After the CRC field of the MAC frame, the STE10/100 will insert the TR code according to IEE802.3u,
clause 24.
■Receive Data Decap sulation
When o perati ng in 100BASE -TX mode the STE10/100 detects a JK code in a preamble as well as a TR
code at the packet end. If a JK code is not detected, the STE10/100 will abort the reception of the frame
and wait for a new JK code dete ction . If a TR code is not detected, the STE10/1 00 will report a CRC
error.
■Deferring
The Inter-Frame Gap (IFG) time is divided into two parts:
1.IFG1 time (64-bit time): If a carrier is detected on the medium during this time, the STE10/100 will
reset the IFG1 time counter and restart to monitor the channel for an idle again.
2.IFG2 time (32-bit time): After counting the IFG2 time the STE10/100 will access the chan nel even
though a carrier has been sensed on the network.
■Collisio n Handlin g
The scheduling of re-transmissions are determined by a controlled randomization process called
“truncated binary expone ntial back-o ff”. At the end of enforcin g a collision (jamming), the STE10/10 0
delays before attem pting to re-transmit the packet. The delay is an integer multiple of slot time. The
number of slot times to delay before the nth re-transmission attempt is chosen as a uniformly distributed
integer r in the range:
0 · r < 2
k
where k = min(n, 10)
Field Description
Preamble A 7-byte field of (10101010b)
Start Frame Delimiter A 1-byte field of (10101011b)
Destination Address A 6-byte field
Source Address A 6-byte field
Length/Type A 2-byte field indicated the frame is in IEEE802.3 format or Ethernet format.
IEEE802.3 format: 0000H ~ 05DCH for Length field
Ethernet format: 05DD ~ FFFFH for Type field
Data *46 ~ 1500 bytes of data information
CRC A 32-bit cyclic redundancy code for error detection
STE10/100
50/66
6.5.2 Transceiver Operation
The trans ceiver portion of the S TE10/100 integrates the IE EE802.3u compliant functions of PCS (physical cod-
i ng sub-layer), PMA (phy sical medium attachment) sub-layer , and PMD (physical medium dependent) s ub-layer
for 100BASE-TX, and the IE EE802.3 compliant func tions of Manc hester enc oding/decodi ng and transceiv er for
10BASE-T. All the functions and operating schemes are described in the following sections.
■100BA SE-TX Tra nsmi t Opera tion
For 100BASE-TX transmissions, the STE10/100 transceiver provides the transmission functions of
PCS, PMA, and PMD for enc oding of MII data nibbles into five-bit code-groups (4B/5B), scram bling,
serialization of scrambled code-groups, converting the serial NRZ code into NRZI code, converting the
NRZI code into MLT3 code, and then driving the MLT3 code into the category 5 Unshielded Twisted
Pair cable through an isolation transformer with the turns ratio of 1.414 : 1.
■Data code-groups Encoder: In normal MII mode applications, the transceiver receives nibble type 4B
data via the TxD0~3 inputs of the MII. These inputs are sampled by the transceiver on the rising edge
of Tx-clk and passed to the 4B/5B encoder to gene rate the 5B code-group used by 100B ASE-TX .
■Idle c ode - gr o up s : In order to establish and maintain the clock synchronization, the transceiver must
keep transmitting signals to medium. The transceiver will generate Idle code-group s for transmission
when there is no actual data to be sent by MAC.
■Start-of-Stream Delimiter-SSD (/J/K/): In a transmission stream, the first 16 nibbles comprise the
MAC preamble . In order to let a netwo rk partner delineate the boundary of a data transm ission
sequence and to authenticate carrier events, the transceiver will replace the first 2 nibbles of the MAC
preamble with /J/K/ code-groups.
■End-of-Stream Delimiter- ESD (/T/R/): In order to indicate the termination of normal data
transmissions, the transceiver will insert 2 nibbles of /T/R/ code-group after the last nibble of the FCS.
■Scrambling: All the encoded data (including the idle, SSD, and ESD code-groups) is passed to the data
scrambler to reduce EMI by spreading the power spectrum using a 10-bit scrambler seed loaded at the
beginning.
■Data conversion of Parallel to Serial, NRZ to NRZI, NRZI to MLT3: After being scrambl ed, the 5B
type transmission data at 25MHz will be converted to a 125HMz serial bit stream by the parallel-to-serial
fun c tio n . Th e bit s trea m w ill be f u rthe r c o nv e rted from NRZ to N RZI forma t, u nle s s the c on v er s ion
function is bypassed by clearing ENRZI (bit 7 of XR10) to 0. After NRZI conversion, the NRZI bit stream
is passed through MLT3 encoder to generate the TP-PMD specified MLT3 code. By using MLT3 code,
the frequency and energy content of the transmission signal is reduced in the UTP, making the system
more easily compliant to FCC EMI specifications.
■Wave-Sh ape r and Media Sign al Driver: In order to reduce the energy of the harmonic frequency of
transmission signals, the transceiver provides a wave-shaper prior the line driver to smooth the rising/
falling edge of transmission signals while maintaining the waveforms’ symmetry. The 100BASE-TX and
10BASE-T wave - sh a ped signals are both passed to the same media signa l driver. This can simplify
system design by employing a single external magnetic connection.
■100BA SE-TX Recei ving Op erati on
For 100BASE-TX receiving operation, the transceiver provides the receiving functions of PMD, PMA,
and PCS for incoming data signals through category 5 UTP cable and an isolation transformer with a
1:1 turns ratio. The receive transc eiver portion includes the adapt ive equalizer and baseline wander,
MLT3 to NRZI data conversion, NRZI to NRZ conversion, serial to parallel conversion, a PLL for clock
and data recove ry, de-scramble r, and the 5B/4B decod er.
■Adaptive Equalizer and Baseline Wander: High speed signals over unshielded (or shielded) twisted
pair cable will experienc e attenuation and phase shift. Thes e effects depend on the signal frequency,
cable type, cable length and the cable connectors. Robust circuits in the transceiver provide reliable
adaptive equalizer and baseline wander compensation for amplitude attenuation and phase shift due to
51/66
STE10/100
transmission line parasitics.
■MLT3 to NRZI Decoder and PLL for Data Recovery: Following adaptive equalizer, baseline wander,
the transceiver converts the resulting MLT3 to NRZI code, which is passed to the Phase Lock Loop
circuits in order to extract the synchronous clock and the original data.
■Data Conversions of NRZI to NRZ and Serial to Parallel: After the data is recovered, it will be passed
to the NRZI-to-NRZ converter to produce a 125MHz serial bit stream. This serial bit stream will be
packed to parallel 5B type for further processing. The NRZI to NRZ conversion may be bypassed by
clearing ENRZI (bit 7 of XR10) to 0.
■De-scrambling and Decoding of 5B/ 4B: The parallel 5B type data is passed to the de-scrambler and
5B/4B decoder to restore it to its original MII nibble representation.
■Carrier sensing: The Carrier Sense (CRS) signal is asserted when the transceiver detects any 2 non-
contiguous zeros wit hin any 10-bit boundary of the receiving bit stream. CRS is de-asserted when ESD
code-group or Idle code-group is detected. In half duplex mode, CRS is asserted during packet
transmission or receive; in full duplex mode, CRS is asserted only during packet reception.
■10BASE-T Tra nsmissi on Opera tion
The parallel-to-serial converter, Manchester Encoder, Link test, Jabber and the transmit wave-shaper
and line driver functions described in the section of “Wave-Shaper and Media Signal Driver” of
“10 0 BASE-T Tran smis s ion Ope ra tion ” are also provided for 10BASE - T tra n s mi ssion. Addi tionally,
Collision detection and SQ E test for half duplex application are provided.
■10BASE-T Recei ve Op erati on
Carrier sense function, receiving filter, PLL for clock and data recovery, Manchester decoder, and serial
to parallel converter functions are provided to support 10BASE-T reception.
■Loop-back Operation of transceiver
The transceiver provides internal loop-back (also called transceiver loop-back) operation for both
100BASE-TX and 10BASE-T o p er at ion. The l oop -b a ck funct ion can b e enabled by setting XLBEN (bit
14 of XR0) to 1. In loop-back mode, the TX± and RX± lines are isolated from the media. The transceiver
also provides remote loop-back operation for 100BASE-TX operation. The remote loop-back operation
can be enabled by setting ENRLB (bit 9 of XR10) to 1.
In 100BASE-TX inter nal loop-back operation, the data is routed from the transm it output of NRZ-to-
NRZI converter and looped back to the receive input of NRZI-to-NRZ conv erter.
In 100BASE-T X r emo te loop-back operation, data is received from RX± pins and passed through the
receive path to the output of the data and clock recovery section, and then looped back to the input of
the NRZI-to-MLT3 convert er and out to the medium via the transm it line drivers.
In 10B ASE- T loop-back operation, the data is passed through th e transmit path to the output of the
Manches ter encoder and then looped back into the input of the Phase Lock Loop circuit in the rece ive
path.
■Full Duplex and Half Duplex Operation of Transceiver
The transceiver can operate in either full duplex or half duplex network applications. In full duplex, both
transmission and reception can take place simultaneously. In full duplex mode, collision (COL) signal is
ignored and carrier sense (CRS) signal is asserted only when the transceiver is receiving.
In half duplex mode, transmiss ion and reception can not take place simultane ously. In half duplex
mode, the collision signal is asserted when transmitted and received signals collide, and carrier sense
is asserted during both transmission and reception.
■Auto-N egotiat ion Operation
The Auto-Negotiation function provides the means to exchange information between the transceiver
and the network partner to automatically configure both to take maximum advantage of their abilities.
The Auto-Negotiation function is controlled by ANEN (bit 12 of XR0).
During Auto-Negotiation information is exchanged with the network partner using Fast Link Pulses
STE10/100
52/66
(FLPs) - a burst of link pulses. There are 16 bits of signalin g information cont ained in the link pulses
which advertise to the remote partne r the capabilities which are represented by the conten ts of ANA
(register XR4). According to this information the partners find out their highest common capabilities by
following the priority sequenc e listed below:
1. 100BASE-TX full duplex
2. 100BASE-TX half duplex
3. 10BASE-T full duplex
4. 10BASE-T half duplex
During power-up or reset, if Auto-Negotiation is enabled, the FLPs will be transmitted and the Auto-Negotia-
tion function will proceed. Otherwise, Auto-Negotiation will not occur until ANEN (bit 12 of XR0) is set to 1.
When the Au to-Negotiati on is disab led, then Network S peed and Duplex Mode ar e selected by pro gramming
the XR0 register.
■Powe r Down Ope ration
The transceiver is designed with a power-down feature which can reduce power consumption
significan tly. Since the power supply of the 100BASE-TX and 10BASE-T circu its are se p ar at e , th e
tr ansceive r ca n turn off the circu it of eith e r the 100BASE-TX or 10BASE-T when the other is active.
6.5.3 Flow Control in Full Duplex Application
The PAUSE function is used to inhibit transmission of data frames for a specified period of time. The S TE10/
100 supports the full duplex protocol of IEEE802.3x. To support the PAUSE function, the STE10/100 imple-
ments the MAC Control Sub-layer functions to decode the MAC Control frames received from MAC control cli-
ents and to execute the relative requests accordingly. When Full Duplex mode and the PAUSE function are
selected after Auto-Negotiation completes (refer to the configuration of XR8), the STE10/100 will enable the
PAUSE function for flow control in a full duplex application. In this section we will describe how the STE10/100
implements the PAUSE function.
■MAC Control Frame and PAUSE Frame
Figure 14. MAC Control Frame Format
The MAC Control frame is distinguished from other MAC frames only by its Length/Type field identifier. The
MAC Control Opcode defined in MAC Control Frame format for th PAUS E function is 0001h, and the P AUSE
time is specified in the MAC Control Parameters field with 2 Octets, representing an unsigned integer, in units
of Slot-Times. The range of possible PAUSE times is 0 to 65535 Slot-Times.
A valid PAUSE frame issued by a MAC control client (e.g., a switch or a bridge) would contain:
■The destination address, set to the globally assigned 48 bit mulitcast address 01-80-C2-00-00-01,
or to the unicast address to which the MAC control client requests to inhibit its transmission of data
frames.
■The MAC Cont rol Opcode field set to 0 001h.
6 Octets Dest inatio n Address
6 Octets S our ce Address
2 Octets Length/Type = 88-08h
2 Octets MAC Control Opcode
MAC Co nt rol P arameter
(minFrameSize - 160) / 8 Octets Reserv ed(pads with zero es )
53/66
STE10/100
■2 Octets of PAUSE time specified in the MAC Control parameter field to indicate the length of time
for which the destination is requeste d to inhibit data frame transmission.
■Receive Operation for PAUSE function
Upon reception of a valid MAC Control frame, the STE10/100 will start a timer fo r the length of time
specified by the MAC Control Parameters field. When the timer value reaches zero, the STE10/100
exits the PAUSE state. Howev er, a PAUSE frame will not affect the transmission of a fram e that has
been submitte d to the MAC (i.e., once a transmit out of the MAC is begun, it can’t be interrupted).
Conversely, the STE10/100 will not begin to transmit a frame more than one slot-time after valid PAUSE
frame is received a with a non-zero PAUSE time. If the STE10/100 receives a PAUSE frame with a zero
PAUSE time value, the STE10/100 exits the PAUSE state immediately.
Figure 15. PAUSE operation receive state diagram
Wait for Transmission Completed
transmission_in_progress = false * DA ≠ (01-80-C2-00-00-01 + Phys-address)
DA = (01-80-C2-00-00-01 + Phys-address)
PAUSE FUNCTION
n_slots_rx = data [17:32]
Start pause_timer (n_slots_rx * slot_time)
UCT
EN D PAUSE
Opcode = PAUSE Function
STE10/100
54/66
6.6 LED Display Op eration
The STE10/100 prov ides 2 LED display modes; the detailed descr iptions of their operation ar e descri bed in the
PIN Description section.
■First mode - 3 LED displays:
100Mbps (on) or 10Mbps (off)
Link (Remains on when link ok) or Activity (Blinks at 10Hz when receiving or transmitting collision-free)
FD (Remains on when in Full duplex mode) or Collision (Blinks at 20Hz when collidions detected)
■Second mo de – 4 LED displays:
100 Link (On when 100M link ok)
10 Link (On when 10M link ok)
Activity (Blinks at 10Hz when receiving or transmitting)
FD (Remains on when in Full duplex mode) or Collision (Blinks at 20Hz when collisions detected)
6.7 Reset Operation
6.7.1 Reset whol e chip
There are two ways to reset the STE10/100: Hardware reset via RST# pin (to ensure proper reset operation,
the RST# signal should be asserted at least 100ms); and software reset via SWR (bit 0 of CSR0) being set to
1 (the STE10/100 will reset all circuits, set registers to their default values, and will clear SWR.
6.7.2 Reset Transceiver only
When XRST (bit 15 of XR0) is set to 1, the transceiver will reset its circuits, will initialize its registers to their
default values, and clear XRST.
6.8 Wake on LAN Function
The STE10/100 can assert a signal to wake up the system when it has received a Magic Packet from the net-
work. The Wake on LAN operation is described as follow.
■The Magic Packe t format:
Valid destination address that can pass the address filter of the STE10/100
The payload of frame must include at least 6 contiguous ‘FF’ followed immediately by 16 repetitions of
IEEE address.
The frame can contain multiple ‘six FF + sixteen IEEE address’ pattern.
Valid CRC
■The Wake on LAN operation
The Wake on LAN enable function is controlled by WOL (bit 18 of CSR18), which is loaded from
EEPRO M after reset or programmed by driver software. If WOL is set and the STE 10/100 rece ives a
Magic Pa cket, it will as s ert the PME # sign al (activ e low) to indic ate reception of a wake up frame and
will set the PME status bit (bit 15 of CSR20).
6.9 AC P I Po wer Ma nag e m en t Fu nct i on
The STE10/100 has a built-in capability for Power Management (PM) which is controlled by the host system
The STE10/100 will provide:
■Compatibility with Device Class Power Management Reference Specification
■Network Device Class, Draft proposal v0.9, Octobe r 1996
■Compatibility with ACPI, Rev 1.0, December 22, 1996
■Compatibility with PCI Bus Power Managem ent Interface Specification, Rev 1.0, January 6, 1997
55/66
STE10/100
■Compatibility with AMD Magic Packet™ Technology.
6.9.1 Power States
■DO (Fully On)
In this state the STE10/100 operat es with full functionality and consumes normal power. While in the
D0 state, if the PCI clock is lower than 16MHz, the STE1 0/100 may not receive or transmit frames
properly.
■D1, D2, and D3hot
In these states, the STE10/10 0 doesn’t respon d to any accesses excep t configuration spac e and full
function context in place. The only network operation the STE10/100 can initiate is a wake-up event.
■D3cold (Power Removed)
In this state all function context is lost. When power is restored, a PCI reset must be asserted and the
function will return to D0.
■D3hot (So ftware Visible D3)
When the STE10/ 100 is brought back to D0 from D3hot the software must perform a full initialization.
The STE10/100 in the D3hot state responds to configuration cycles as long as power and clock are
supplied. This requires the device to perf orm an internal reset and r eturn to a power-up reset condition
without the RST# pin asserted.
Table 13. Power Stage
Device
State PCI Bus
State Function
Context Clock Power Supported
Actions to
Function
Supported
Actions from
Function
D0 B0 Full function context in
place Full speed Full
power Any PCI
transaction A ny PCI
transaction or
interrupt
D1 B0, B1 Configuration
maintained. No Tx and
Rx except wake-up
events
Stopped to
Full speed PCI configuration
access Only wake-up
events
D2 B0, B1,
B2 Configuration
maintained. No Tx and
Rx
Stopped to
Full speed PCI configuration
access(B0, B1)
D3hot B0, B1,
B2 Configuration lost, full
initialization required
upon return to D0
Stopped to
Full speed PCI configuration
access(B0, B1)
D3cold B3 All configuration lost.
Power-on defaults in
place on return to D0
No clock No power Power-on reset
STE10/100
56/66
7.0 GENER AL EEPROM FORMAT DESCR IPTI ON
Tab le 14. C onnec tion Ty pe D ef i ni tion
Offset Length Description
0 2 STE10/100 Signature: 0x81, 0x09
2 1 Format major version: 0x02,
old ROM forma t version 0x01 is for STE10/100-MAC only.
3 1 Format minor version: 0x00
4 4 Reserved
86
IEEE network address: ID1, ID2, ID3, ID4, ID5, ID6
E 1 IEEE ID checksum1:
Sm0=0, carry=0
SUM=Sm6 where Smi=(Smi-1<<1)+(carry from shift)+IDi
F 1 IEEE ID checksum2:
Reserved, should be zero.
10 1 PHY type, 0xFF: Internal PHY (STE10/100 only)
11 1 Reserved, should be zero.
12 2 Default Connection Type, see Table 15
14 0B Reserved, should be zero.
1F 1 Flow Control Field,
00: Disable Flow Control function,
01: Enable Flow Control function
20 2 PCI Device ID.
22 2 PCI Vendor ID.
24 2 PCI Subsystem ID.
26 2 PCI Subsystem Vendor ID.
28 1 MIN_GNT value.
29 1 MAX_LAT value.
2A 4 Cardbus CIS point er.
2E 2 CSR18 (CR) bit 31-16 recall data.
30 4E Reserved, should be zero.
7E 2 CheckSum, the least significant two bytes of FCS for data stored in offset 0..7D of
EEPROM
57/66
STE10/100
Tab le 15. C onnec tion Ty pe D ef i ni tion
0xFFFF Software Driver Default
0x0100 Auto-Negotiation
0x0200 Power-on Auto-detection
0x0400 Auto Sense
0x0000 10BaseT
0x0001 BNC
0x0002 AUI
0x0003 100BaseTx
0x0004 100BaseT4
0x0005 100BaseFx
0x0010 10BaseT Full Duplex
0x0013 100BaseTx Full Duplex
0x0015 100BaseFx Full Duplex
STE10/100
58/66
8.0 ELECTRICAL SPECIFICATIONS AND TIMINGS
Table 16. Absolute Maximum Ratings
Parameter Value
Supply Voltage(Vcc) -0.5 V to 7.0 V
Input Voltage -0.5 V to VCC + 0.5 V
Output Voltage -0.5 V to VCC + 0.5 V
Storage Temperature -65 °C to 150 °C(-85°F to 302°F)
Ambient Temperature 0°C to 70°C(32°F to 158°F)
ESD Protection 2000V
Table 17. General DC Specifications
Symbol Parameter Test Condition Min. Typ. Max. Units
General DC
Vcc Supply Voltage 4.75 5.25 V
Icc Power Supply 300 mA
PCI Interface DC Specfications
Vilp I nput LOW Volta ge -0.5 0 .8 V
Vihp Input HIGH Volta ge 2.0 5.5 V
Iilp Input LOW Leakage Current Vin = .8V -10 10 µA
Iihp Input HIGH Leakage Current Vin = 2.0V -10 10 µA
Volp Output LOW Voltage Iout =3mA/6mA . .55 V
Vohp Output HIGH Voltage Iout =-2mA 2.4 V
Cinp Input Pin Capaci tance 5 8 pF
Cclkp CLK Pin Capacitance 5 8 pF
Cidsel IDSEL Pin Capacitance 5 8 pF
Lpinp Pin Inductance N/A nH
Flash/EEPROM Interface DC Specifications
Vilf Input LOW Volta ge -0.5 0.8 V
Vihf I nput HIGH Voltage 2.0 5.5 V
Iif I nput Leaka ge Curren t -10 1 0 µA
Volf Output LOW Voltage Iout=3mA,6mA .55 V
Vohf Output HIGH Voltage Iout=-2mA 2.4 V
Cinf Input Pin Capaci tance 5 8 pF
59/66
STE10/100
10BASE-T Voltage/Current Characteristics
Rid10 Input Differential Resis tance DC TBD kΩ
Vida10 Input Differential Accep t Pe ak
Voltage 5MHz ~ 10MHz 585 3100 mV
Vidr10 Input Differential Rejec t Pea k
Voltage 5MHz ~ 10MHz 0 585 mV
Vicm10 Input Common Mode Voltage TBD V
Vod10 Output Differential Peak Voltage 2200 2800 V
Icct10 Line Driver Supply TBD mA
100BASE-TX Voltage/Current Characteristics
Rid100 I nput Differential Resistance TBD kΩ
Vida1 00 I nput Differential Accep t Pe ak
Voltage 200 1000 mV
Vidr100 Input Differential Rejec t Peak
Voltage 0200mV
Vicm100 Input Common Mode Voltage TBD V
Vod100 Output Differential Peak Voltage 950 1050 V
Icct100 Line Driver Supply TBD mA
Table 18. AC Specifications
Symbol Parameter Test Condition Min. Typ. Max. Units
PCI Signaling AC Specifications
Ioh(AC) Switching Current High Vout=.7Vcc -32Vcc mA
Iol(AC) Switching Current Low Vout=.18Vcc 38Vcc mA
Icl Low Clamp Current -3<Vin<-1 -
25+(Vi
n+1)/
.015
mA
Tr Unloaded Output Rise Time 1 4 V/ns
Tf Unloaded Output Fall Time 1 4 V/ns
Table 17. General DC Specifications
Symbol Parameter Test Condition Min. Typ. Max. Units
STE10/100
60/66
8.1 Timing Specifications
Table 19. PCI Clock Speci fications
Figure 16. PCI Clock Waveform
Table 20. X1 Specifications
Symbol Parameter Test Condition Min. Typ. Max. Units
Tc Clock Cycle Time 30 50 ns
Th Clock High Time 11 -- ns
Tl Clock Low Time 11 -- ns
Clock Slew Rate 1 4 V/ns
Symbol Parameter Test Condition Min. Typ. Max. Units
TX1d X1 Duty Cycle 45 50 55 %
TX1p X1 Period 30 ns
TX1t X1 Tolerance PPM
Table 21. PCI Timing
Symbol Parameter Test Condition Min. Typ. Max. Units
Tval Clock to Signal Valid Delay
(bussed signals) 211ns
Tval(ptp) Clock to Signal Valid Delay
(point to point) 211ns
Ton Float to Active Delay 2 ns
Toff Active to Float Delay 28 ns
1.5V
2.4V
0.4V
Th
Tc
2.0V
Tl
0.8V
2V pick to pi ck
61/66
STE10/100
Figure 17. PCI Timings
Tsu Input Set up Time to Clock
(bussed signals) 7ns
Tsu(ptp) Input Set up Time to Clock
(point to point) 10,12 ns
Th Input Hold Time from Clock 0 ns
Th Input Hold Time from Clock 0 ns
Trst Reset Active Time after Power
Stable 1ms
Trst-clk Reset Active Time after CLK
Stable 100 µs
Trst-off Reset Active to Output Float
delay 40 ns
Table 21. PCI Timing
Symbol Parameter Test Condition Min. Typ. Max. Units
CLK
2.4V
0.4V
Tval
OUTP UT Delay
Ton
1.5V
1.5V
Tri -state OUTPUT
IN P UT 1.5V 1.5V
Toff
Tsu Th
STE10/100
62/66
Table 22. Flash Interface Timi ngs
Figure 18. Flash write timings
Symbol Parameter Test Condition Min. Typ. Max. Units
Tfcyc Read/Write Cycle Time ns
Tfce Address to Read Data Setup
Time ns
Tfce CS# to Read Data Setup Time ns
Tfoe OE# Active to Read Data Setup
Time ns
Tfdf OE# Inactive to Data Driven
Delay Time ns
Tfas Address Setup Time before WE# ns
Tfah Address Hold Time after WE# ns
Tfcs C S# Setup Time before WE# ns
Tfch Address Hold Time after WE# ns
Tfds Data Setup Time ns
Tfdh Data Hold Time ns
Tfwpw Write Pulse Width ns
Tfwph Write Pulse Width High ns
Tfasc Address Setup Time before CS# ns
Tfahc Address Hold Time after CS# ns
CS#
WE#
DATA
ADDRESS
Tfcyc
Tfasc Tfah
Tfasw Tahw
Tfwpw
Tfds Tfdh
Tfcss Tfcsh
Tfwph
63/66
STE10/100
Figure 19. Flash read timings
Table 23. EEPROM Interface Timings
Fig ur e 20. Seria l EEPROM ti mi ng
Symbol Parameter Test Condition Min. Typ. Max. Units
Tscf Serial Clock Frequency
Tecss Delay from CS High to SK High
Tecsh Delay from SK Low to CS Low
Tedts Setup Time of DI to SK
Tedth Hold Time of DI after SK
Tecsl CS Low Time
ADDRESS
CS#
OE#
DATA
Tfce
Tfoe
Tfasd Tfdf
Tfcyc
CS
CLK
DI
Tecss Tecsh Tecsl
Tedts Tedth
STE10/100
64/66
Table 24. 10BASE-T Normal Link Pulse(NLP) Timings Specifications
Figure 21. Normal Link Pulse timings
Table 25. Auto-Negotiation Fast Link Pulse(FLP) Timing s Specification s
Figure 22. Fast Link Pulse timing
Table 26. 100BASE-TX Transmitter AC Timings Specification
Symbol Parameter Test Condition Min. Typ. Max. Units
NLP Width 10Mbps 100 ns
NLP Period 10Mbps 8 24 ms
Symbol Parameter Test Condition Min. Typ. Max. Units
Tflpw FLP Width 100
Clock pulse to clock pulse period 111 125 139
Clock pulse to Data pulse period 55.5 62.5 69.5
Number of pulses in one burst 17 33
Burst Width 2
FLP Burst period 8 16 24
Symbol Parameter Test Condition Min. Typ. Max. Units
Tjit TDP-TDN Differential Output
Peak Jitter 1.4 ps
Tnpw
Tnpc
65/66
STE10/100
DIM. mm inch
MIN. TYP. MAX. MIN. TYP. MAX.
A 3.04 3.40 0.12 0.134
A1 0.25 0.33 0.010 0.013
A2 2.57 2.71 2.87 0.101 0.107 0.113
b 0.13 0.28 0.005 0.011
C 0.13 0.23 0.005 0.009
D 20 0.787
E 14 0.551
e 0.5 0.02
HD 23.2 0.913
HE 17.2 0.677
L 0.73 0.88 1/03 0.029 0.035 0.041
L1 1.60 0.063
ZD 0.75 0.03
ZE 0.75 0.03
ccc 0.12 0.005
Angle 0°(min.), 7°(max.)
L dimension is measured at gauge plane at 0.25 above the seating
plane
A
A2
A1
C
38
39
64
65102
103
128
ZE
ZD
E
PIN 1 ID
HE
D
HD
e
1
0.7 DEGREES
b
PQF128CM
L
L1
MC DA -B
0.12
.005
CDC
0.25 GAGE PLANE
S S
PQFP128 (14x20x2.7mm)
May 1999 1020818
OUTLINE AND
MECHANICAL DATA
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences
of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted
by i m pl i cat i on or oth erwi se under any pat ent or pat ent r i ghts of S T M i croelectroni cs. Spec i ficat i ons m ent i oned i n this public at ion are subject
to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics product s are not
authorized f or use as c ritical com ponents in li fe su pport dev i ces or sy st ems wi t hout exp ress wri tt en approva l of STMi croelectr onics.
The ST logo is a registered trademark of STMicroelectronics
199 9 STM i croelectr oni cs - All Ri ghts Reserved
STMicroelectronics GROUP OF COMPANIES
Australia - Brazil - Chi na - Finl and - France - Germ any - Hong Ko ng - India - Ita l y - Japan - Mala ysia - M a l t a - Morocco - Si n gapore - S pai n
- Sweden - Sw i tz erl and - Uni ted Kingdom - U.S .A .
http://www.st.com
66/66
STE10/100
