Data Sheet
March 2008
CC025 Triple-Output-Series Power Modules:
18 Vdc to 36 Vdc Input; 25 W
The CC025 Triple-Output-Series Power Modules use
advanced, surface-mount technology and deliver high-qual-
ity, compact, dc-dc conversion at an economical price.
Features
nSmall size: 71.1 mm x 61.0 mm x 12.7 mm
(2.80 in. x 2.40 in. x 0.50 in.)
nLow output noise
nIndustry-standard pinout
nMetal case
n2:1 input voltage range
nRemote on/off (positive logic)
nUL* Recognized, CSA Certified, and VDE
Licensed
nWithin FCC and CISPR Class A radiated limits
Applications
nDistributed power architectures
nTelecommunications
Options
nIsolated case ground pin
nShort pins: 2.79 mm ± 0.25 mm
(0.110 in. ± 0.010 in.)
nHeat sink available for extended operation
nNegative logic remote on/off
Description
The CC025 Triple-Output-Series Power Modules are
dc-dc converters that operate over an input voltage
range of 18 Vdc to 36 Vdc and provide three outputs.
These modules offer extremely low noise levels with
industry-standard pinouts in a small footprint. Each
highly reliable and efficient unit features remote
on/off and current limit.
The maximum total output power of the CC025
Triple-Output-Series Power Modules is limited to
25 W. The main output (VO1) is designed to deliver
the entire 25 W. The auxiliary outputs (VO2 and VO3)
can provide a total of 22.5 W as long as the total out-
put power does not exceed 25 W.
Efficiency greater than 80%, a wide operating tem-
perature range, and a metal case are additional fea-
tures of these modules.
* UL is a registered trademark of Underwriters Laboratories, Inc.
CSA is a registered trademark of Canadian Standards Associa-
tion.
22 Lineage Power
Data Sheet
March 2008
18 Vdc to 36 Vdc Input; 25 W
CC025 Triple-Output-Series Power Modules:
Absolute Maximum Ratings
Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are abso-
lute stress ratings only. Functional operation of the device is not implied at these or any other conditions in excess
of those given in the operations sections of the data sheet. Exposure to absolute maximum ratings for extended
periods can adversely affect device reliability.
Parameter Symbol Min Max Unit
Input Voltage Continuous VI50 V
I/O Isolation Voltage:
dc
Transient (1 minute)
500
850
V
V
Operating Case Temperature TC40 100 °C
Storage Temperature Tstg 55 125 °C
Electrical Specifications
Unless otherwise indicated, specifications apply to all modules over all operating input voltage, resistive load, and
temperature conditions.
Table 1. Input Specifications
Parameter Symbol Min Typ Max Unit
Operating Input Voltage VI18 28 36 Vdc
Maximum Input Current
(VI = 0 V to 36 V; IO = IO, max; see Figure 1.)
II, max 3.0 A
Inrush Transient i2t 0.2 A2s
Input Reflected-ripple Current, Peak-to-peak
(5 Hz to 20 MHz, 12 µH source impedance;
TC = 25 °C; see Figure 18 and Design
Considerations section.)
30 mAp-p
Input Ripple Rejection (120 Hz) 60 dB
Fusing Considerations
CAUTION: This power module is not internally fused. An input line fuse must always be used.
This encapsulated power module can be used in a wide variety of applications, ranging from simple stand-alone
operation to an integrated part of a sophisticated power architecture. To preserve maximum flexibility, internal fus-
ing is not included; however, to achieve maximum safety and system protection, always use an input line fuse. The
safety agencies require a normal-blow, dc fuse with a maximum rating of 5 A in series with the ungrounded input
lead. Based on the information provided in this data sheet on inrush energy and maximum dc input current, the
same type of fuse with a lower rating can be used. Refer to the fuse manufacturer’s data for further information.
Lineage Power 3
Data Sheet
March 2008 18 Vdc to 36 Vdc Input; 25 W
CC025 Triple-Output-Series Power Modules:
Electrical Specifications (continued)
Table 2. Output Specifications
Parameter Device Symbol Min Typ Max Unit
Output Voltage
(Over all operating input voltage, resistive
load, and temperature conditions until end
of life. See Figure 20.)
CC025ABK-M
CC025ACL-M
VO1
VO2
VO3
VO1
VO2
VO3
4.80
10.80
–10.80
4.80
13.77
–13.77
5.20
13.70
–13.70
5.20
17.20
–17.20
Vdc
Vdc
Vdc
Vdc
Vdc
Vdc
Output Voltage Set Point
(VI = 28 V; TC = 25 °C; IO1 = 2.0 A,
IO2 = IO3 = 0.5 A)
CC025ABK-M
CC025ACL-M
VO1, set
VO2, set
VO3, set
VO1, set
VO2, set
VO3, set
4.90
11.83
–11.83
4.90
14.84
–14.84
5.00
12.20
–12.20
5.00
15.30
–15.30
5.10
12.57
–12.57
5.10
15.76
–15.76
Vdc
Vdc
Vdc
Vdc
Vdc
Vdc
Output Regulation:
Line (VI = 18 V to 36 V)
Load (See Figures 5—8.)
(IO1 = IO, min to IO, max, IO2 = IO3 = IO, min)
Temperature (See Figures 2—4.)
(TC = – 40 °C to +100 °C)
All
All
All
VO1
VO1
0.1
0.1
0.5
0.2
0.2
1.5
%
%
%
Output Ripple and Noise
(See Figure 19.):
RMS
Peak-to-peak (5 Hz to 20 MHz)
All
All
VO1
VO2, VO3
VO1
VO2, VO3
25
30
100
150
mVrms
mVrms
mVp-p
mVp-p
Output Current
(At IO < IO, min, the modules may exceed
output ripple specifications.)
CC025ABK-M
CC025ACL-M
IO1
IO2, IO3
IO1
IO2, IO3
0.5
0.1
0.5
0.1
5.0
1.0
5.0
0.83
A
A
A
A
Output Current-limit Inception
(VO = 90% of VO, nom and minimum load on
other outputs. See Figures 9—12.)
CC025ABK-M
CC025ACL-M
IO1
IO2, IO3
IO1
IO2, IO3
6
2
6
2
7.5
3.0
7.5
3.0
A
A
A
A
Output Short-circuit Current
(VO = 1 V and minimum load on other
outputs.)
CC025ABK-M
CC025ACL-M
IO1
IO2, IO3
IO1
IO2, IO3
8
3
8
3
10.5
4.5
10.5
4.5
A
A
A
A
Efficiency
(VI = 28 V; TC = 25 °C; see Figures 13, 14,
and 20.):
IO1 = 2.5 A, IO2 = IO3 = 0.5 A
IO1 = 2.0 A, IO2 = IO3 = 0.5 A
CC025ABK-M
CC025ACL-M
η
η
79
79
82
82
%
%
44 Lineage Power
Data Sheet
March 2008
18 Vdc to 36 Vdc Input; 25 W
CC025 Triple-Output-Series Power Modules:
General Specifications
Parameter Min Typ Max Unit
Calculated MTBF (IO = 80% of IO, max; TC = 40 °C) 2,906,000 hours
Weight 113 (4.0) g (oz.)
Dynamic Response
(ýIO/ýt = 1 A/10 µs, VI = 28 V, TC = 25 °C):
Load Change from IO = 50% to 75% of
IO, max:
Peak Deviation
Settling Time (VO < 10% peak
deviation)
Load Change from IO = 50% to 25% of
IO, max:
Peak Deviation
Settling Time (VO < 10% peak
deviation)
All
All
All
All
VO1
VO1
80
1
80
0.5
mV
ms
mV
ms
Table 3. Isolation Specifications
Parameter Min Typ Max Unit
Isolation Capacitance 0.02 µF
Isolation Resistance 10
Table 2. Output Specifications (continued)
Parameter Device Symbol Min Typ Max Unit
Electrical Specifications (continued)
Lineage Power 5
Data Sheet
March 2008 18 Vdc to 36 Vdc Input; 25 W
CC025 Triple-Output-Series Power Modules:
Feature Specifications
Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature
conditions. See Feature Descriptions and Design Considerations for further information.
Parameter Device Symbol Min Typ Max Unit
Remote On/Off
(VI = 0 V to 36 V; open collector or equivalent
compatible; signal referenced to VI(–) terminal.
See Figures 17 and 21 and Feature
Descriptions.):
CC025XXX-M (positive logic):
Logic Low—Module Off
Logic High—Module On
CC025XXX1-M (negative logic):
Logic Low—Module On
Logic High—Module Off
Module Specifications:
On/Off Current—Logic Low
On/Off Voltage:
Logic Low
Logic High (Ion/off = 0)
Open Collector Switch Specifications:
Leakage Current During Logic High
(Von/off = 10 V)
Output Low Voltage During Logic Low
(Ion/off = 1 mA)
Turn-on Time
(IO = 80% of IO, max; VO within ±1% of steady
state)
Output Voltage Overshoot (See Figure 17.)
All
All
All
All
All
All
All
Ion/off
Von/off
Von/off
Ion/off
Von/off
0
5
0
1.0
1.2
10
50
1.2
5
mA
V
V
µA
V
ms
%
Output Overvoltage Clamp CC025ABK-M
CC025ACL-M
VO1
VO2
VO3
VO1
VO2
VO3
6
15
–15
6
19
–19
6.8
17
–17
6.8
21
–21
V
V
V
V
V
V
Output Voltage Set-point Adjustment Range All 90 110 % VO, nom
6Lineage Power
Data Sheet
March 2008
18 Vdc to 36 Vdc Input; 25 W
CC025 Triple-Output-Series Power Modules:
Characteristic Curves
8-1077(C)
Figure 1. CC025 Triple-Output-Series Typical Input
Characteristics
8-1078(C)
Figure 2. CC025 Triple-Output-Series Typical
Output Voltage Variation of 5 V Output
Over Ambient Temperature Range
8-1079(C)
Figure 3. CC025 Triple-Output-Series Typical
Output Voltage Variation of 12 V Output
Over Ambient Temperature Range
8-1080(C)
Figure 4. CC025 Triple-Output-Series Typical
Output Voltage Variation of 15 V Output
Over Ambient Temperature Range
Lineage Power 7
Data Sheet
March 2008 18 Vdc to 36 Vdc Input; 25 W
CC025 Triple-Output-Series Power Modules:
Characteristic Curves (continued)
8-1081(C)
Figure 5. CC025ABK-M Typical Load Regulation
8-1082(C)
Figure 6. CC025ABK-M Typical Cross Regulation
with Respect to IO1
8-1083(C)
Figure 7. CC025ACL-M Typical Load Regulation
8-1084(C)
Figure 8. CC025ACL-M Typical Cross Regulation
with Respect to IO1
Note: Given the same load conditions, Output 3 has regulation characteristics similar to Output 2, except the
polarity is negative.
8Lineage Power
Data Sheet
March 2008
18 Vdc to 36 Vdc Input; 25 W
CC025 Triple-Output-Series Power Modules:
Characteristic Curves (continued)
8-1085(C)
Figure 9. CC025ABK-M Typical 5 V Output Characteristics
8-1086(C)
Figure 10. CC025ABK-M Typical 12 V Output Characteristics
8-1087(C)
Figure 11. CC025ACL-M Typical 5 V Output Characteristics
Data Sheet
March 2008
Lineage Power 9
18 Vdc to 36 Vdc Input; 25 W
CC025 Triple-Output-Series Power Modules:
Characteristic Curves (continued)
8-1088(C)
Figure 12. CC025ACL-M Typical 15 V Output Characteristics
8-1089(C)
Note: Loads varied proportionately from minimum to 50% of full load.
Figure 13. CC025ABK-M Typical Converter
Efficiency
8-1090(C)
Note: Loads varied proportionately from minimum to 50% of full load.
Figure 14. CC025ACL-M Typical Converter
Efficiency
10 Lineage Power
Data Sheet
March 2008
18 Vdc to 36 Vdc Input; 25 W
CC025 Triple-Output-Series Power Modules:
Characteristic Curves (continued)
8-1098(C)
Figure 15. CC025 Triple-Output-Series Typical
Output Voltage for a Step Load Change
from 75% to 50% of Full Load on
Output 1
8-1099(C)
Figure 16. CC025 Triple-Output-Series Typical
Output Voltage for a Step Load Change
from 25% to 50% of Full Load on
Output 1
8-1100(C)
Figure 17. CC025 Triple-Output-Series Typical
Output Voltage Start-Up when Signal
Applied to Remote On/Off
Test Configurations
8-489(C).a
Note: Input reflected-ripple current is measured with a simulated
source impedance (LTEST) of 12 µH. Capacitor CS offsets pos-
sible battery impedance. Current is measured at the input of
the module.
Figure 18. Input Reflected-Ripple Test Setup
Lineage Power 11
Data Sheet
March 2008 18 Vdc to 36 Vdc Input; 25 W
CC025 Triple-Output-Series Power Modules:
Test Configurations (continued)
8-810(C).c
Note: Use the specified ceramic capacitor. Scope measurement
should be made by using a BNC socket. Position the load
between 50 mm (2 in.) and 75 mm (3 in.) from the
module.
Figure 19. Output Noise Measurement Test Setup
8-749(C).c
Note: All measurements are taken at the module terminals. When
socketing, place Kelvin connections at module terminals to
avoid measurement errors due to socket contact resistance.
η
VOj +() VCOM[]IOj
j1=
3
VI+() VI()()+[]II
------------------------------------------------------- 100×=
Figure 20. Triple Output Voltage and Efficiency
Measurement Test Setup
Design Considerations
Input Source Impedance
The power module should be connected to a low
ac-impedance input source. Highly inductive source im-
pedances can affect the stability of the power module. A
33 µF electrolytic capacitor (ESR < 0.7 ¾ at 100 kHz)
mounted close to the power module helps to ensure
the stability of the unit.
Safety Considerations
For safety-agency approval of the system in which the
power module is used, the power module must be
installed in compliance with the spacing and separation
requirements of the end-use safety agency standard,
i.e., UL-1950, CSA 22.2-950, and EN60950.
For the converter output to be considered meeting the
requirements of safety extra-low voltage (SELV), the
input must meet SELV requirements.
If the input meets extra-low voltage (ELV) require-
ments, then the converter’s output is considered ELV.
The input to these units is to be provided with a maxi-
mum 5 A normal-blow fuse in the ungrounded lead.
1212 Lineage Power
Data Sheet
March 2008
18 Vdc to 36 Vdc Input; 25 W
CC025 Triple-Output-Series Power Modules:
Feature Descriptions
Output Overvoltage Clamp
The output overvoltage clamp consists of control cir-
cuitry, independent of the primary regulation loop, that
monitors the voltage on the output terminals. The con-
trol loop of the clamp has a higher voltage set point
than the primary loop (see Feature Specifications
table). This provides a redundant voltage control that
reduces the risk of output overvoltage.
Current Limit
To provide protection in a fault (output overload) condi-
tion, the unit is equipped with internal current-limiting
circuitry. At the point of current-limit inception, the unit
shifts from voltage control to current control. If the out-
put voltage is pulled very low during a severe fault, the
current-limit circuit can exhibit either foldback or
tailout characteristics (output current decrease or
increase). The unit operates normally once the output
current is brought back into its specified range.
Output Voltage Set-Point Adjustment
The output voltage adjustment feature provides the
capability of increasing or decreasing the output volt-
age set point of a module. This can be accomplished
by using an external resistor connected between the
TRIM pin and either the VO1(+) or common pins. With
an external resistor between the TRIM and common
pins (Radj-up), the output voltage set point (VO, adj)
increases.
Radj-up 42.35
VO, adj VO, nom
----------------------------------
⎝⎠
⎛⎞
=
Note: The output voltage adjustment range must not
exceed 110% of the nominal output voltage
between the VO1(+) and common terminals.
With an external resistor connected between the TRIM
and VO1(+) pins (Radj-down), the output voltage set point
(VO, adj) decreases.
Radj-down VO, adj 2.5()16.94×
VO, nom VO, adj
--------------------------------------------------
⎝⎠
⎛⎞
=
Note: The output voltage adjustment must be 90% or
more of the nominal output voltage between the
VO1(+) and common terminals.
Remote On/Off
Two remote on/off options are available. Positive logic
remote on/off turns the module on during a logic high
voltage on the REMOTE ON/OFF pin, and off during a
logic low. Negative logic remote on/off, suffix code “1,”
turns the module off during a logic high and on during a
logic low.
To turn the power module on and off, the user must
supply a switch to control the voltage between the on/
off terminal and the VI(–) terminal (Von/off). The switch
can be an open collector or equivalent (see Figure 21).
A logic low is Von/off = 0 V to 1.2 V. The maximum Ion/off
during a logic low is 1 mA. The switch should maintain
a logic low-voltage while sinking 1 mA.
During a logic high, the maximum Von/off generated by
the power module is 10 V. The maximum allowable
leakage current of the switch at Von/off = 10 V is 50 µA.
8-758(C).a
Figure 21. Remote On/Off Implementation
CAUTION: To avoid damaging the module or exter-
nal circuitry, the VI(–) pin must be con-
nected to the –48þV source before or
simultaneously to connecting the
ON/OFF pin to the –48þV source (either
directly or through the external on/off
circuitry).
Grounding Considerations
For modules without the isolated case ground pin
option, the case is internally connected to the VI(–) pin.
For modules with the isolated case ground pin, the
VI(–) is not connected to the case.
Data Sheet
March 2008
Lineage Power 13
18 Vdc to 36 Vdc Input; 25 W
CC025 Triple-Output-Series Power Modules:
Thermal Considerations
8-866(C).b
Note: Dimensions are in millimeters and (inches). Drawing is not to scale.
Figure 22. Thermal Test Setup
The 25 W triple output power modules are designed to
operate in a variety of thermal environments. As with
any electronic component, sufficient cooling must be
provided to ensure reliable operation. Heat dissipating
components inside the module are thermally coupled to
the case to enable heat removal by conduction, con-
vection, and radiation to the surrounding environment.
The thermal data presented is based on measure-
ments taken in a wind tunnel. The test setup shown in
Figure 22 was used to collect data. Actual performance
can vary depending on the particular application
environment.
1414 Lineage Power
Data Sheet
March 2008
18 Vdc to 36 Vdc Input; 25 W
CC025 Triple-Output-Series Power Modules:
Thermal Considerations (continued)
Basic Thermal Performance
The maximum operating temperature of the CC025 Tri-
ple-Output-Series Power Modules at a given operating
condition can be predicted by combining the power dis-
sipation curves (Figures 23 through 27), the power der-
ating curve (Figure 28), and the thermal resistance
curve (Figure 29).
Use Figures 23 through 28 and the steps below to pre-
dict the safe operating region for many different operat-
ing and environmental conditions.
1. Calculate the total output power.
POtotal = (IO1 x VO1) + (IO2 x VO2) + (IO3 x VO3)
2. Use POtotal with the appropriate figure (Figure 23
or 25) to determine the fixed losses (PP) associ-
ated with operating at POtotal. These losses are
independent of which output the load is being
drawn from.
3. Use the desired output current (IO1) with Figure 25
to determine PS1, which is the additional power
being dissipated due to loading of the main output.
4. Repeat Step 3 for outputs 2 and 3 using the appro-
priate figure (Figure 23 or 27) to determine PS2 and
PS3, which is the power dissipated due to loading of
the auxiliary outputs.
5. Find the total power dissipated (PDtotal) by adding
the four power dissipations obtained in Steps 2
through 4.
PDtotal = PP + PS1 + PS2 + PS3
6. Use the estimated total power dissipated (PDtotal)
along with Figure 28 to determine the maximum
ambient temperature allowable for a given air
velocity.
For example, consider the CC025ABK power module
operating with 27 V input and output currents
IO1 = 2.5 A, IO2 = 0.5 A, IO3 = 0.5 A.
The total output power (POtotal) is 24.5 W. The total
power dissipation is PDtotal = 4.86 W, which is obtained
by adding:
PP= 4.5 W (from Figure 23)
PS1 = 0.22 W (from Figure 25)
PS2 = 0.07 W (from Figure 23)
PS3 = 0.07 W (from Figure 23)
Figure 28 shows that in natural convection the maxi-
mum operating ambient temperature for this module is
approximately 66 °C.
Keep in mind that the procedure above provides
approximations of the temperature and air velocities
required to keep the case temperature below its maxi-
mum rating. The maximum case temperature, as moni-
tored at the point shown in Figure 22, should be
maintained at 100 °C or less under all conditions.
Air Velocity
The air velocity required to maintain a desired maxi-
mum case temperature for a given power dissipation
and ambient temperature can be calculated using
Figure 28 and the following equation:
θCA TCmax TA
PDtotal
----------------------------
=
where:
nθCA is the thermal resistance from case-to-ambient
air (°C/W)
nTCmax is the desired maximum case temperature (°C)
nTA is the ambient inlet temperature (°C)
nPDtotal is the total power dissipated by the module
(W) at the desired operating condition
For example, to maintain a maximum case temperature
of 85 °C with an ambient inlet temperature of 65 °C and
a power dissipation of 4.86 W, the thermal resistance is:
θCA ð 85 °C65 °C
4.86 W
------------------------------------- 4.1°C/W=
This corresponds to an airflow greater than 0.38 ms–1
(75 fpm) in Figure 28.
Lineage Power 15
Data Sheet
March 2008 18 Vdc to 36 Vdc Input; 25 W
CC025 Triple-Output-Series Power Modules:
Thermal Considerations (continued)
Air Velocity (continued)
8-1091(C)
Figure 23. CC025ABK-M Fixed Losses, PP
8-1092(C)
Figure 24. CC025ACL-M Fixed Losses, PP
8-1093(C)
Figure 25. CC025ABK-M, CC025ACL-M Losses,
Associated with 5 V Output, PS1
8-1094(C)
Figure 26. CC025ABK-M, Losses Associated with
±12 V Output, PS2/PS3
1616 Lineage Power
Data Sheet
March 2008
18 Vdc to 36 Vdc Input; 25 W
CC025 Triple-Output-Series Power Modules:
Thermal Considerations (continued)
Air Velocity (continued)
8-1095(C)
Figure 27. CC025ACL-M Losses Associated with
±15 V Output, PS2/PS3
8-1130(C)
Figure 28. Total Power Dissipation vs. Local
Ambient Temperature and Air Velocity
8-1101(C)
Figure 29. Case-to-Ambient Thermal Resistance
vs. Air Velocity
Use of Heat Sinks and Cold Plates
The CC025 Triple-Output-Series case includes
through-threaded M3 x 0.5 mounting holes allowing
attachment of heat sinks or cold plates from either side
of the module. The mounting torque must not exceed
0.56 N/m (5 in.-lb).
The following thermal model can be used to determine
the required thermal resistance of the sink to provide
the necessary cooling:
PD
θCS
TATc Ts
θSA
where PD is the power dissipated by the module, θCS
represents the interfacial contact resistance between
the module and the sink, and θSA is the sink-to-ambient
thermal impedance (°C/W). For thermal greases or
foils, a value of θCS = 0.1 °C/W to 0.3 °C/W is typical.
The required θSA is calculated from the following equa-
tion:
θSA TCTA
PDtotal
----------------- θCS=
Note that this equation assumes that all dissipated
power must be shed by the sink. Depending on the
user-defined application environment, a more accurate
model including heat transfer from the sides and rear of
the module can be used. This equation provides a con-
servative estimate in such instances.
For further thermal information on these modules, refer
to the Thermal Management for CC-, CW, DC, DW-
Series 25 W to 30 W Board-Mounted Power Modules
Technical Note.
Lineage Power 17
Data Sheet
March 2008 18 Vdc to 36 Vdc Input; 25 W
CC025 Triple-Output-Series Power Modules:
Outline Diagram
Dimensions are in millimeters and (inches).
Copper paths must not be routed beneath the power module standoffs.
Tolerances: x.x ± 0.5 mm (0.02 in.), x.xx ± 0.25 mm (0.010 in.).
Note: For standard modules, VI(–) is internally connected to the case and the CASE pin is not present. If the CASE
GROUND pin is chosen, device code suffix 7, then VI(–) is not connected to the case and the CASE
GROUND pin is floating.
Top View
Side View
Bottom View
8-846(C).b
18 Lineage Power
Data Sheet
March 2008
18 Vdc to 36 Vdc Input; 25 W
CC025 Triple-Output-Series Power Modules:
Recommended Hole Pattern
Component-side footprint.
Dimensions are in millimeters and (inches).
Recommended hole size for pin: 1.27 mm (0.050 in.)
8-846(C).b
Lineage Power 19
Data Sheet
March 2008 18 Vdc to 36 Vdc Input; 25 W
CC025 Triple-Output-Series Power Modules:
Ordering Information
Table 4. Ordering Information Table
Input
Voltage
Output
Voltage
Output
Power
Remote
On/Off Logic
Device
Code Comcode
18 V—36 V +5 V, ±12 V 25 W positive CC025ABK-M 107586919
18 V—36 V +5 V, ±15 V 25 W positive CC025ACL-M 107586927
Optional features may be ordered using the device code suffixes shown below. To order more than one option, list
suffixes in numerically descending order followed by the -M suffix, indicating metric (M3 x 0.5 heat sink hardware).
The heat sinks designed for this package have an M prefix, i.e., MHSTxxx45 and MHSLxxx45 (see Thermal
Energy Management CC-, CW-, DC-, and DW-Series 25 W to 30 W Board-Mounted Power Modules Techn i c a l
Note).
Table 5. Options Table
Option Device Code
Suffix
Short pins: 2.79 mm ± 0.25 mm
(0.110 in. ± 0.010 in.)
8
Isolated case ground pin 7
Negative on/off logic 1
Please contact your Lineage Power Account Manager or Field Application Engineer for pricing and availability.
Data Sheet
March 2008
18 Vdc to 36 Vdc Input; 25 W
CC025 Triple-Output-Series Power Modules:
March 2008
DS97-451EPS (Replaces DS97-450EPS)
World Wide Headquarters
Lineag e Po wer Co rporation
30 00 Skyline Drive, Mesquite, TX 75149, USA
+1-800-526-7819
(Outside U.S.A.: +1- 97 2-2 84 -2626)
www.line ag ep ower.com
e-m ail: techsupport1@linea gepower.com
Asia-Pacific Headquarters
Tel: +65 6 41 6 4283
Europe, Middle-East and Afric a Headquarters
Tel: +49 8 9 6089 286
India Headquarters
Tel: +91 80 28411633
Lineage Power reserves the right to make changes to the product(s) or information contained herein without notice. No liability is assumed as a result of their use or
application. No rights under any patent accompany the sale of any such product(s) or information.
© 2008 Lineage Power Corporation, (Mesquite, Texas) All International Rights Reserved.