Description
•125°C maximum total temperature operation
•Surface mount inductors designed for higher
speed switch mode applications requiring
lower inductance and high current
•Dual conductors allow for low inductance and high
current or high inductance and lower current
•Inductance range from .047uH to 0.480uH
•Current range up to 42 Amps
•Meets UL 94V-0 flammability standard
•Ferrite core material
Applications
•Next generation microprocessors
Environmental Data
•Storage temperature range: -40°C to +125°C
•Operating ambient temperature range: -40°C to +125°C
(range is application specific).
•Solder reflow temperature: +260°C max. for 10 seconds
max.
Packaging
•Supplied in tape and reel packaging, 1700 (FP2-S and
FP2-D) and 950 (FP2-S200 and FP2-VXXX) per reel
Parallel Mode
PartInductance OCL(1) IRMS(2) ISAT(3) DCR(4) Height Volt-µ
Number µH µH±Amps Amps ΩSec (VµS)
(rated) 15% nom. ref.(5)
Single Conductor
FP2-S047-R 0.047 0.047 39.0 42.0 0.00024 3.00 0.75
FP2-S068-R 0.068 0.068 39.0 32.0 0.00024 3.00 0.75
FP2-S082-R 0.082 0.082 39.0 26.0 0.00024 3.00 0.75
FP2-S100-R 0.100 0.100 39.0 22.0 0.00024 3.00 0.75
FP2-S120-R 0.120 0.120 39.0 18.0 0.00024 3.00 0.75
FP2-S200-R 0.200 0.200 37.0 19.0 0.00028 5.00 0.99
FP2-V050-R 0.050 0.050 37.0 70.0 0.00028 5.00 0.99
FP2-V100-R 0.100 0.100 37.0 40.0 0.00028 5.00 0.99
FP2-V120-R 0.120 0.120 37.0 33.0 0.00028 5.00 0.99
FP2-V150-R 0.150 0.150 37.0 25.5 0.00028 5.00 0.99
Double Conductor
FP2-D047-R 0.047 0.047 37.0 42.0 0.00026 3.00 0.75
FP2-D068-R 0.068 0.068 37.0 32.0 0.00026 3.00 0.75
FP2-D082-R 0.082 0.082 37.0 26.0 0.00026 3.00 0.75
FP2-D100-R 0.100 0.100 37.0 22.0 0.00026 3.00 0.75
FP2-D120-R 0.120 0.120 37.0 18.0 0.00026 3.00 0.75
Series Mode
Part Inductance OCL(1) IRMS(2) ISAT(3) DCR(4) Height Volt-µ(5)
Number µH ref. µH Amps Amps ΩSec (VµS)
(rated) ref. ref. ref.
Double Conductor
FP2-D047-R 0.188 0.188 16.0 21.0 0.0013 3.00 1.50
FP2-D068-R 0.272 0.272 16.0 16.0 0.0013 3.00 1.50
FP2-D082-R 0.328 0.328 16.0 13.0 0.0013 3.00 1.50
FP2-D100-R 0.400 0.400 16.0 11.0 0.0013 3.00 1.50
FP2-D120-R 0.480 0.480 16.0 9.0 0.0013 3.00 1.50
Notes: (1) Open Circuit Inductance T
est Parameters: 1MHz, .100Vrms, 0.0Adc.
(2) RMS current for an approximate ∆T of 40°Cwithout core loss. It is
recommended that the temperature of the part not exceed 125°C.
(3) Peak current for approximately 30% rolloff at 20°C.
(4) DCR limits 20°C.
(5) Applied Volt-Time product (V-µS) across the inductor.This value
represents the applied V-µS at 500KHz necessary to generate a core
loss equal to 10% of the total losses for 40°Ctemperature rise.
FLAT-PAC™
Low Profile Inductors
(Surface Mount)