www.vishay.com
4
Document Number: 70049
S-61921–Rev. G, 16-Oct-06
Vishay Siliconix
DG401/403/405
Notes:
a. Refer to PROCESS OPTION FLOWCHART.
b. Room = 25 °C, Full = as determined by the operating temperature suffix.
c. Typical values are for DESIGN AID ONLY, not guaranteed nor subject to production testing.
d. The algebraic convention whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet.
e. Guaranteed by design, not subject to production test.
f. VIN = input voltage to perform proper function.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation
of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum
rating conditions for extended periods may affect device reliability.
SPECIFICATIONSa
Parameter
Symbol
Test Conditions
Unless Specified
V+ = 15 V, V– = - 15 V
VL = 5 V, VIN = 2.4 V, 0.8 VfTempb Typc
D Suffix
- 40 to 85 °C
Unit Mind Maxd
Analog Switch
Analog Signal RangeeVANALOG Full - 15 15 V
Drain-Source
On-Resistance rDS(on)
IS = - 10 mA, VD = ± 10 V
V+ = 13.5 V, V- = - 13.5 V
Room
Full 30 45
55 Ω
Δ Drain-Source
On-Resistance ΔrDS(on)
IS = - 10 mA, VD = ± 5 V, 0 V
V+ = 16.5 V, V- = - 16.5 V
Room
Full 33
5
Switch Off Leakage Current
IS(off) V+ = 16.5 V, V- = - 16.5 V
VD = ± 15.5 V, VS = ± 15.5 V
Room
Hot - 0.01 - 0.5
- 5
0.5
5
nA
ID(off) Room
Hot - 0.01 - 0.5
- 5
0.5
5
Channel On Leakage Current ID(on)
V+ = 16.5 V, V- = - 16.5 V
VS = VD = ± 15.5 V
Room
Hot - 0.04 - 1
- 10
1
10
Digital Control
Input Current VIN Low IIL
VIN under test = 0.8 V
All Other = 2.4 V Full 0.005 - 1 1
µA
Input Current VIN High IIH
VIN under test = 2.4 V
All Other = 0.8 V Full 0.005 - 1 1
Dynamic Characteristics
Tur n - O n T i m e tON RL = 300 Ω, CL = 35 pF
See Figure 2
Room 75 150
ns
Tur n - O f f T i m e tOFF Room 30 100
Break-Before-Make
Time Delay (DG403) tDRL = 300 Ω, CL = 35 pF Room 35 5
Charge Injection Q CL = 10 nF
Vgen = 0 V, Rgen = 0 ΩRoom 60 pC
Off Isolation Reject Ratio OIRR RL = 100 Ω, CL = 5 pF
f = 1 MHz
Room 72 dB
Channel-to-Channel Crosstalk XTA L K Room 90
Source Off Capacitance CS(off)
f = 1 MHz, VS = 0 V
Room 12
pFDrain Off Capacitance CD(off) Room 12
Channel On Capacitance CD, CS(on) Room 39
Power Supplies
Positive Supply Current I+
V+ = 16.5 V, V- = - 16.5 V
VIN = 0 or 5 V
Room
Full
0.01 1
5
µA
Negative Supply Current I- Room
Full
- 0.01 - 1
- 5
Logic Supply Current ILRoom
Full
0.01 1
5
Ground Current IGND Room
Full
- 0.01 - 1
- 5