To our customers, Old Company Name in Catalogs and Other Documents On April 1st, 2010, NEC Electronics Corporation merged with Renesas Technology Corporation, and Renesas Electronics Corporation took over all the business of both companies. Therefore, although the old company name remains in this document, it is a valid Renesas Electronics document. We appreciate your understanding. Renesas Electronics website: http://www.renesas.com April 1st, 2010 Renesas Electronics Corporation Issued by: Renesas Electronics Corporation (http://www.renesas.com) Send any inquiries to http://www.renesas.com/inquiry. Notice 1. 2. 3. 4. 5. 6. 7. All information included in this document is current as of the date this document is issued. Such information, however, is subject to change without any prior notice. Before purchasing or using any Renesas Electronics products listed herein, please confirm the latest product information with a Renesas Electronics sales office. Also, please pay regular and careful attention to additional and different information to be disclosed by Renesas Electronics such as that disclosed through our website. Renesas Electronics does not assume any liability for infringement of patents, copyrights, or other intellectual property rights of third parties by or arising from the use of Renesas Electronics products or technical information described in this document. No license, express, implied or otherwise, is granted hereby under any patents, copyrights or other intellectual property rights of Renesas Electronics or others. You should not alter, modify, copy, or otherwise misappropriate any Renesas Electronics product, whether in whole or in part. Descriptions of circuits, software and other related information in this document are provided only to illustrate the operation of semiconductor products and application examples. You are fully responsible for the incorporation of these circuits, software, and information in the design of your equipment. Renesas Electronics assumes no responsibility for any losses incurred by you or third parties arising from the use of these circuits, software, or information. When exporting the products or technology described in this document, you should comply with the applicable export control laws and regulations and follow the procedures required by such laws and regulations. You should not use Renesas Electronics products or the technology described in this document for any purpose relating to military applications or use by the military, including but not limited to the development of weapons of mass destruction. Renesas Electronics products and technology may not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable domestic or foreign laws or regulations. Renesas Electronics has used reasonable care in preparing the information included in this document, but Renesas Electronics does not warrant that such information is error free. Renesas Electronics assumes no liability whatsoever for any damages incurred by you resulting from errors in or omissions from the information included herein. Renesas Electronics products are classified according to the following three quality grades: "Standard", "High Quality", and "Specific". The recommended applications for each Renesas Electronics product depends on the product's quality grade, as indicated below. You must check the quality grade of each Renesas Electronics product before using it in a particular application. You may not use any Renesas Electronics product for any application categorized as "Specific" without the prior written consent of Renesas Electronics. Further, you may not use any Renesas Electronics product for any application for which it is not intended without the prior written consent of Renesas Electronics. Renesas Electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the use of any Renesas Electronics product for an application categorized as "Specific" or for which the product is not intended where you have failed to obtain the prior written consent of Renesas Electronics. The quality grade of each Renesas Electronics product is "Standard" unless otherwise expressly specified in a Renesas Electronics data sheets or data books, etc. "Standard": 8. 9. 10. 11. 12. Computers; office equipment; communications equipment; test and measurement equipment; audio and visual equipment; home electronic appliances; machine tools; personal electronic equipment; and industrial robots. "High Quality": Transportation equipment (automobiles, trains, ships, etc.); traffic control systems; anti-disaster systems; anticrime systems; safety equipment; and medical equipment not specifically designed for life support. "Specific": Aircraft; aerospace equipment; submersible repeaters; nuclear reactor control systems; medical equipment or systems for life support (e.g. artificial life support devices or systems), surgical implantations, or healthcare intervention (e.g. excision, etc.), and any other applications or purposes that pose a direct threat to human life. You should use the Renesas Electronics products described in this document within the range specified by Renesas Electronics, especially with respect to the maximum rating, operating supply voltage range, movement power voltage range, heat radiation characteristics, installation and other product characteristics. Renesas Electronics shall have no liability for malfunctions or damages arising out of the use of Renesas Electronics products beyond such specified ranges. Although Renesas Electronics endeavors to improve the quality and reliability of its products, semiconductor products have specific characteristics such as the occurrence of failure at a certain rate and malfunctions under certain use conditions. Further, Renesas Electronics products are not subject to radiation resistance design. Please be sure to implement safety measures to guard them against the possibility of physical injury, and injury or damage caused by fire in the event of the failure of a Renesas Electronics product, such as safety design for hardware and software including but not limited to redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other appropriate measures. Because the evaluation of microcomputer software alone is very difficult, please evaluate the safety of the final products or system manufactured by you. Please contact a Renesas Electronics sales office for details as to environmental matters such as the environmental compatibility of each Renesas Electronics product. Please use Renesas Electronics products in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. Renesas Electronics assumes no liability for damages or losses occurring as a result of your noncompliance with applicable laws and regulations. This document may not be reproduced or duplicated, in any form, in whole or in part, without prior written consent of Renesas Electronics. Please contact a Renesas Electronics sales office if you have any questions regarding the information contained in this document or Renesas Electronics products, or if you have any other inquiries. (Note 1) "Renesas Electronics" as used in this document means Renesas Electronics Corporation and also includes its majorityowned subsidiaries. (Note 2) "Renesas Electronics product(s)" means any product developed or manufactured by or for Renesas Electronics. User's Manual 16 R8C/2K Group, R8C/2L Group Hardware Manual RENESAS MCU R8C FAMILY / R8C/2x SERIES All information contained in these materials, including products and product specifications, represents information on the product at the time of publication and is subject to change by Renesas Electronics Corp. without notice. Please review the latest information published by Renesas Electronics Corp. through various means, including the Renesas Electronics Corp. website (http://www.renesas.com). Rev.1.10 2007.12 Notes regarding these materials 1. This document is provided for reference purposes only so that Renesas customers may select the appropriate Renesas products for their use. Renesas neither makes warranties or representations with respect to the accuracy or completeness of the information contained in this document nor grants any license to any intellectual property rights or any other rights of Renesas or any third party with respect to the information in this document. 2. Renesas shall have no liability for damages or infringement of any intellectual property or other rights arising out of the use of any information in this document, including, but not limited to, product data, diagrams, charts, programs, algorithms, and application circuit examples. 3. You should not use the products or the technology described in this document for the purpose of military applications such as the development of weapons of mass destruction or for the purpose of any other military use. When exporting the products or technology described herein, you should follow the applicable export control laws and regulations, and procedures required by such laws and regulations. 4. All information included in this document such as product data, diagrams, charts, programs, algorithms, and application circuit examples, is current as of the date this document is issued. Such information, however, is subject to change without any prior notice. Before purchasing or using any Renesas products listed in this document, please confirm the latest product information with a Renesas sales office. Also, please pay regular and careful attention to additional and different information to be disclosed by Renesas such as that disclosed through our website. (http://www.renesas.com ) 5. Renesas has used reasonable care in compiling the information included in this document, but Renesas assumes no liability whatsoever for any damages incurred as a result of errors or omissions in the information included in this document. 6. When using or otherwise relying on the information in this document, you should evaluate the information in light of the total system before deciding about the applicability of such information to the intended application. Renesas makes no representations, warranties or guaranties regarding the suitability of its products for any particular application and specifically disclaims any liability arising out of the application and use of the information in this document or Renesas products. 7. With the exception of products specified by Renesas as suitable for automobile applications, Renesas products are not designed, manufactured or tested for applications or otherwise in systems the failure or malfunction of which may cause a direct threat to human life or create a risk of human injury or which require especially high quality and reliability such as safety systems, or equipment or systems for transportation and traffic, healthcare, combustion control, aerospace and aeronautics, nuclear power, or undersea communication transmission. If you are considering the use of our products for such purposes, please contact a Renesas sales office beforehand. Renesas shall have no liability for damages arising out of the uses set forth above. 8. Notwithstanding the preceding paragraph, you should not use Renesas products for the purposes listed below: (1) artificial life support devices or systems (2) surgical implantations (3) healthcare intervention (e.g., excision, administration of medication, etc.) (4) any other purposes that pose a direct threat to human life Renesas shall have no liability for damages arising out of the uses set forth in the above and purchasers who elect to use Renesas products in any of the foregoing applications shall indemnify and hold harmless Renesas Technology Corp., its affiliated companies and their officers, directors, and employees against any and all damages arising out of such applications. 9. You should use the products described herein within the range specified by Renesas, especially with respect to the maximum rating, operating supply voltage range, movement power voltage range, heat radiation characteristics, installation and other product characteristics. Renesas shall have no liability for malfunctions or damages arising out of the use of Renesas products beyond such specified ranges. 10. Although Renesas endeavors to improve the quality and reliability of its products, IC products have specific characteristics such as the occurrence of failure at a certain rate and malfunctions under certain use conditions. Please be sure to implement safety measures to guard against the possibility of physical injury, and injury or damage caused by fire in the event of the failure of a Renesas product, such as safety design for hardware and software including but not limited to redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other applicable measures. Among others, since the evaluation of microcomputer software alone is very difficult, please evaluate the safety of the final products or system manufactured by you. 11. In case Renesas products listed in this document are detached from the products to which the Renesas products are attached or affixed, the risk of accident such as swallowing by infants and small children is very high. You should implement safety measures so that Renesas products may not be easily detached from your products. Renesas shall have no liability for damages arising out of such detachment. 12. This document may not be reproduced or duplicated, in any form, in whole or in part, without prior written approval from Renesas. 13. Please contact a Renesas sales office if you have any questions regarding the information contained in this document, Renesas semiconductor products, or if you have any other inquiries. General Precautions in the Handling of MPU/MCU Products The following usage notes are applicable to all MPU/MCU products from Renesas. For detailed usage notes on the products covered by this manual, refer to the relevant sections of the manual. If the descriptions under General Precautions in the Handling of MPU/MCU Products and in the body of the manual differ from each other, the description in the body of the manual takes precedence. 1. Handling of Unused Pins Handle unused pins in accord with the directions given under Handling of Unused Pins in the manual. The input pins of CMOS products are generally in the high-impedance state. In operation with an unused pin in the open-circuit state, extra electromagnetic noise is induced in the vicinity of LSI, an associated shoot-through current flows internally, and malfunctions occur due to the false recognition of the pin state as an input signal become possible. Unused pins should be handled as described under Handling of Unused Pins in the manual. 2. Processing at Power-on The state of the product is undefined at the moment when power is supplied. The states of internal circuits in the LSI are indeterminate and the states of register settings and pins are undefined at the moment when power is supplied. In a finished product where the reset signal is applied to the external reset pin, the states of pins are not guaranteed from the moment when power is supplied until the reset process is completed. In a similar way, the states of pins in a product that is reset by an on-chip power-on reset function are not guaranteed from the moment when power is supplied until the power reaches the level at which resetting has been specified. 3. Prohibition of Access to Reserved Addresses Access to reserved addresses is prohibited. The reserved addresses are provided for the possible future expansion of functions. Do not access these addresses; the correct operation of LSI is not guaranteed if they are accessed. 4. Clock Signals After applying a reset, only release the reset line after the operating clock signal has become stable. When switching the clock signal during program execution, wait until the target clock signal has stabilized. When the clock signal is generated with an external resonator (or from an external oscillator) during a reset, ensure that the reset line is only released after full stabilization of the clock signal. Moreover, when switching to a clock signal produced with an external resonator (or by an external oscillator) while program execution is in progress, wait until the target clock signal is stable. 5. Differences between Products Before changing from one product to another, i.e. to one with a different part number, confirm that the change will not lead to problems. The characteristics of MPU/MCU in the same group but having different part numbers may differ because of the differences in internal memory capacity and layout pattern. When changing to products of different part numbers, implement a system-evaluation test for each of the products. How to Use This Manual 1. Purpose and Target Readers This manual is designed to provide the user with an understanding of the hardware functions and electrical characteristics of the MCU. It is intended for users designing application systems incorporating the MCU. A basic knowledge of electric circuits, logical circuits, and MCUs is necessary in order to use this manual. The manual comprises an overview of the product; descriptions of the CPU, system control functions, peripheral functions, and electrical characteristics; and usage notes. Particular attention should be paid to the precautionary notes when using the manual. These notes occur within the body of the text, at the end of each section, and in the Usage Notes section. The revision history summarizes the locations of revisions and additions. It does not list all revisions. Refer to the text of the manual for details. The following documents apply to the R8C/2K Group, R8C/2L Group. Make sure to refer to the latest versions of these documents. The newest versions of the documents listed may be obtained from the Renesas Technology Web site. Document Type Datasheet Description Document Title Document No. REJ03B0219 Hardware overview and electrical characteristics R8C/2K Group, R8C/2L Group Group Datasheet R8C/2K Group, This hardware Hardware manual Hardware specifications (pin assignments, R8C/2L Group manual memory maps, peripheral function Hardware Manual specifications, electrical characteristics, timing charts) and operation description Note: Refer to the application notes for details on using peripheral functions. Software manual Description of CPU instruction set R8C/Tiny Series REJ09B0001 Software Manual Available from Renesas Application note Information on using peripheral functions and Technology Web site. application examples Sample programs Information on writing programs in assembly language and C Renesas Product specifications, updates on documents, technical update etc. 2. Notation of Numbers and Symbols The notation conventions for register names, bit names, numbers, and symbols used in this manual are described below. (1) Register Names, Bit Names, and Pin Names Registers, bits, and pins are referred to in the text by symbols. The symbol is accompanied by the word "register," "bit," or "pin" to distinguish the three categories. Examples the PM03 bit in the PM0 register P3_5 pin, VCC pin (2) Notation of Numbers The indication "b" is appended to numeric values given in binary format. However, nothing is appended to the values of single bits. The indication "h" is appended to numeric values given in hexadecimal format. Nothing is appended to numeric values given in decimal format. Examples Binary: 11b Hexadecimal: EFA0h Decimal: 1234 3. Register Notation The symbols and terms used in register diagrams are described below. XXX Register b7 b6 b5 b4 b3 *1 b2 b1 b0 Symbol XXX 0 Bit Symbol XXX0 Address XXX Bit Name XXX bits XXX1 After Reset 00h Function RW 1 0: XXX 0 1: XXX 1 0: Do not set. 1 1: XXX RW RW (b2) Nothing is assigned. If necessary, set to 0. When read, the content is undefined. (b3) Reserved bits Set to 0. RW XXX bits Function varies according to the operating mode. RW XXX4 *3 XXX5 WO XXX6 RW XXX7 XXX bit *2 b1 b0 0: XXX 1: XXX *4 RO *1 Blank: Set to 0 or 1 according to the application. 0: Set to 0. 1: Set to 1. X: Nothing is assigned. *2 RW: Read and write. RO: Read only. WO: Write only. -: Nothing is assigned. *3 * Reserved bit Reserved bit. Set to specified value. *4 * Nothing is assigned Nothing is assigned to the bit. As the bit may be used for future functions, if necessary, set to 0. * Do not set to a value Operation is not guaranteed when a value is set. * Function varies according to the operating mode. The function of the bit varies with the peripheral function mode. Refer to the register diagram for information on the individual modes. 4. List of Abbreviations and Acronyms Abbreviation ACIA bps CRC DMA DMAC GSM Hi-Z IEBus I/O IrDA LSB MSB NC PLL PWM SFR SIM UART VCO Full Form Asynchronous Communication Interface Adapter bits per second Cyclic Redundancy Check Direct Memory Access Direct Memory Access Controller Global System for Mobile Communications High Impedance Inter Equipment bus Input/Output Infrared Data Association Least Significant Bit Most Significant Bit Non-Connection Phase Locked Loop Pulse Width Modulation Special Function Registers Subscriber Identity Module Universal Asynchronous Receiver/Transmitter Voltage Controlled Oscillator All trademarks and registered trademarks are the property of their respective owners. Table of Contents SFR Page Reference ........................................................................................................................... B - 1 1. Overview ......................................................................................................................................... 1 1.1 1.1.1 1.1.2 1.2 1.3 1.4 1.5 2. Features ..................................................................................................................................................... 1 Applications .......................................................................................................................................... 1 Specifications ........................................................................................................................................ 2 Product List ............................................................................................................................................... 6 Block Diagram ......................................................................................................................................... 8 Pin Assignment .......................................................................................................................................... 9 Pin Functions ........................................................................................................................................... 11 Central Processing Unit (CPU) ..................................................................................................... 12 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.8.1 2.8.2 2.8.3 2.8.4 2.8.5 2.8.6 2.8.7 2.8.8 2.8.9 2.8.10 3. Data Registers (R0, R1, R2, and R3) ...................................................................................................... Address Registers (A0 and A1) ............................................................................................................... Frame Base Register (FB) ....................................................................................................................... Interrupt Table Register (INTB) .............................................................................................................. Program Counter (PC) ............................................................................................................................. User Stack Pointer (USP) and Interrupt Stack Pointer (ISP) .................................................................. Static Base Register (SB) ........................................................................................................................ Flag Register (FLG) ................................................................................................................................ Carry Flag (C) ..................................................................................................................................... Debug Flag (D) ................................................................................................................................... Zero Flag (Z) ....................................................................................................................................... Sign Flag (S) ....................................................................................................................................... Register Bank Select Flag (B) ............................................................................................................ Overflow Flag (O) .............................................................................................................................. Interrupt Enable Flag (I) ..................................................................................................................... Stack Pointer Select Flag (U) .............................................................................................................. Processor Interrupt Priority Level (IPL) ............................................................................................. Reserved Bit ........................................................................................................................................ 13 13 13 13 13 13 13 13 13 13 13 13 13 13 14 14 14 14 Memory ......................................................................................................................................... 15 3.1 3.2 R8C/2K Group ........................................................................................................................................ 15 R8C/2L Group ......................................................................................................................................... 16 4. Special Function Registers (SFRs) ............................................................................................... 17 5. Resets ........................................................................................................................................... 24 5.1 5.1.1 5.1.2 5.2 5.3 5.4 5.5 5.6 5.7 Hardware Reset ....................................................................................................................................... When Power Supply is Stable ............................................................................................................. Power On ............................................................................................................................................ Power-On Reset Function ....................................................................................................................... Voltage Monitor 0 Reset ......................................................................................................................... Voltage Monitor 1 Reset ......................................................................................................................... Voltage Monitor 2 Reset ......................................................................................................................... Watchdog Timer Reset ............................................................................................................................ Software Reset ......................................................................................................................................... A-1 27 27 27 29 30 30 30 31 31 6. Voltage Detection Circuit .............................................................................................................. 32 6.1 6.1.1 6.1.2 6.1.3 6.2 6.3 6.4 7. VCC Input Voltage .................................................................................................................................. Monitoring Vdet0 ............................................................................................................................... Monitoring Vdet1 ............................................................................................................................... Monitoring Vdet2 ............................................................................................................................... Voltage Monitor 0 Reset ......................................................................................................................... Voltage Monitor 1 Interrupt and Voltage Monitor 1 Reset ..................................................................... Voltage Monitor 2 Interrupt and Voltage Monitor 2 Reset ..................................................................... 39 39 39 39 40 41 43 Programmable I/O Ports ............................................................................................................... 45 7.1 7.2 7.3 7.4 7.5 8. Functions of Programmable I/O Ports ..................................................................................................... Effect on Peripheral Functions ................................................................................................................ Pins Other than Programmable I/O Ports ................................................................................................ Port settings ............................................................................................................................................. Unassigned Pin Handling ........................................................................................................................ 45 46 46 58 68 Processor Mode ............................................................................................................................ 69 8.1 Processor Modes ...................................................................................................................................... 69 9. Bus ................................................................................................................................................ 70 10. Clock Generation Circuit ............................................................................................................... 71 10.1 10.2 10.2.1 10.2.2 10.3 10.3.1 10.3.2 10.3.3 10.3.4 10.3.5 10.3.6 10.3.7 10.3.8 10.4 10.4.1 10.4.2 10.4.3 10.5 10.5.1 10.6 10.6.1 10.6.2 10.6.3 10.6.4 XIN Clock ............................................................................................................................................... On-Chip Oscillator Clocks ...................................................................................................................... Low-Speed On-Chip Oscillator Clock ................................................................................................ High-Speed On-Chip Oscillator Clock ............................................................................................... CPU Clock and Peripheral Function Clock ............................................................................................. System Clock ...................................................................................................................................... CPU Clock .......................................................................................................................................... Peripheral Function Clock (f1, f2, f4, f8, and f32) ............................................................................. fOCO ................................................................................................................................................... fOCO40M ........................................................................................................................................... fOCO-F ............................................................................................................................................... fOCO-S ............................................................................................................................................... fOCO128 ............................................................................................................................................. Power Control .......................................................................................................................................... Standard Operating Mode ................................................................................................................... Wait Mode .......................................................................................................................................... Stop Mode ........................................................................................................................................... Oscillation Stop Detection Function ....................................................................................................... How to Use Oscillation Stop Detection Function ............................................................................... Notes on Clock Generation Circuit ......................................................................................................... Stop Mode ........................................................................................................................................... Wait Mode .......................................................................................................................................... Oscillation Stop Detection Function ................................................................................................... Oscillation Circuit Constants .............................................................................................................. A-2 81 82 82 82 83 83 83 83 83 83 83 83 83 84 84 86 89 92 92 95 95 95 95 95 11. Protection ...................................................................................................................................... 96 12. Interrupts ....................................................................................................................................... 97 12.1 12.1.1 12.1.2 12.1.3 12.1.4 12.1.5 12.1.6 12.2 12.2.1 12.2.2 12.3 12.4 12.5 12.6 12.6.1 12.6.2 12.6.3 12.6.4 12.6.5 13. Interrupt Overview .................................................................................................................................. 97 Types of Interrupts .............................................................................................................................. 97 Software Interrupts ............................................................................................................................. 98 Special Interrupts ................................................................................................................................ 99 Peripheral Function Interrupt .............................................................................................................. 99 Interrupts and Interrupt Vectors ........................................................................................................ 100 Interrupt Control ............................................................................................................................... 102 INT Interrupt ......................................................................................................................................... 111 INTi Interrupt (i = 0, 1, 3) ................................................................................................................. 111 INTi Input Filter (i = 0, 1, 3) ............................................................................................................. 113 Key Input Interrupt ................................................................................................................................ 114 Address Match Interrupt ........................................................................................................................ 116 Timer RC Interrupt, Timer RD Interrupt (Interrupts with Multiple Interrupt Request Sources) .......... 118 Notes on Interrupts ................................................................................................................................ 120 Reading Address 00000h .................................................................................................................. 120 SP Setting .......................................................................................................................................... 120 External Interrupt and Key Input Interrupt ....................................................................................... 120 Changing Interrupt Sources .............................................................................................................. 121 Changing Interrupt Control Register Contents ................................................................................. 122 ID Code Areas ............................................................................................................................ 123 13.1 Overview ............................................................................................................................................... 123 13.2 Functions ............................................................................................................................................... 123 13.3 Notes on ID Code Areas ........................................................................................................................ 124 13.3.1 Setting Example of ID Code Areas ................................................................................................... 124 14. Option Function Select Area ....................................................................................................... 125 14.1 Overview ............................................................................................................................................... 14.2 OFS Register ......................................................................................................................................... 14.3 Notes on Option Function Select Area .................................................................................................. 14.3.1 Setting Example of Option Function Select Area ............................................................................. 15. 15.1 15.2 16. 125 126 127 127 Watchdog Timer .......................................................................................................................... 128 Count Source Protection Mode Disabled .............................................................................................. 132 Count Source Protection Mode Enabled ............................................................................................... 133 Timers ......................................................................................................................................... 134 16.1 Timer RA ............................................................................................................................................... 16.1.1 Timer Mode ...................................................................................................................................... 16.1.2 Pulse Output Mode ........................................................................................................................... 16.1.3 Event Counter Mode ......................................................................................................................... 16.1.4 Pulse Width Measurement Mode ...................................................................................................... 16.1.5 Pulse Period Measurement Mode ..................................................................................................... 16.1.6 Notes on Timer RA ........................................................................................................................... 16.2 Timer RB ............................................................................................................................................... 16.2.1 Timer Mode ...................................................................................................................................... A-3 136 139 141 143 145 148 151 152 157 16.2.2 Programmable Waveform Generation Mode .................................................................................... 16.2.3 Programmable One-shot Generation Mode ...................................................................................... 16.2.4 Programmable Wait One-Shot Generation Mode ............................................................................. 16.2.5 Notes on Timer RB ........................................................................................................................... 16.3 Timer RC ............................................................................................................................................... 16.3.1 Overview ........................................................................................................................................... 16.3.2 Registers Associated with Timer RC ................................................................................................ 16.3.3 Common Items for Multiple Modes ................................................................................................. 16.3.4 Timer Mode (Input Capture Function) ............................................................................................. 16.3.5 Timer Mode (Output Compare Function) ......................................................................................... 16.3.6 PWM Mode ....................................................................................................................................... 16.3.7 PWM2 Mode ..................................................................................................................................... 16.3.8 Timer RC Interrupt ........................................................................................................................... 16.3.9 Notes on Timer RC ........................................................................................................................... 16.4 Timer RD ............................................................................................................................................... 16.4.1 Count Sources ................................................................................................................................... 16.4.2 Buffer Operation ............................................................................................................................... 16.4.3 Synchronous Operation ..................................................................................................................... 16.4.4 Pulse Output Forced Cutoff .............................................................................................................. 16.4.5 Input Capture Function ..................................................................................................................... 16.4.6 Output Compare Function ................................................................................................................ 16.4.7 PWM Mode ....................................................................................................................................... 16.4.8 Reset Synchronous PWM Mode ....................................................................................................... 16.4.9 Complementary PWM Mode ............................................................................................................ 16.4.10 PWM3 Mode ..................................................................................................................................... 16.4.11 Timer RD Interrupt ........................................................................................................................... 16.4.12 Notes on Timer RD ........................................................................................................................... 17. Serial Interface ............................................................................................................................ 316 17.1 Clock Synchronous Serial I/O Mode ..................................................................................................... 17.1.1 Polarity Select Function .................................................................................................................... 17.1.2 LSB First/MSB First Select Function ............................................................................................... 17.1.3 Continuous Receive Mode ................................................................................................................ 17.2 Clock Asynchronous Serial I/O (UART) Mode .................................................................................... 17.2.1 Bit Rate ............................................................................................................................................. 17.3 Notes on Serial Interface ....................................................................................................................... 18. 160 163 167 170 174 174 176 186 192 197 203 208 214 215 216 221 222 224 225 227 241 258 271 281 295 308 310 322 325 325 326 327 331 332 Hardware LIN .............................................................................................................................. 333 18.1 18.2 18.3 18.4 18.4.1 18.4.2 18.4.3 18.4.4 18.5 18.6 Features ................................................................................................................................................. Input/Output Pins .................................................................................................................................. Register Configuration .......................................................................................................................... Functional Description .......................................................................................................................... Master Mode ..................................................................................................................................... Slave Mode ....................................................................................................................................... Bus Collision Detection Function ..................................................................................................... Hardware LIN End Processing ......................................................................................................... Interrupt Requests .................................................................................................................................. Notes on Hardware LIN ........................................................................................................................ A-4 333 334 335 337 337 340 344 345 346 347 19. A/D Converter ............................................................................................................................. 348 19.1 19.2 19.3 19.4 19.5 19.6 19.7 20. One-Shot Mode ..................................................................................................................................... Repeat Mode .......................................................................................................................................... Sample and Hold ................................................................................................................................... A/D Conversion Cycles ......................................................................................................................... Internal Equivalent Circuit of Analog Input .......................................................................................... Output Impedance of Sensor under A/D Conversion ............................................................................ Notes on A/D Converter ........................................................................................................................ Flash Memory ............................................................................................................................. 362 20.1 20.2 20.3 20.3.1 20.3.2 20.4 20.4.1 20.4.2 20.4.3 20.4.4 20.5 20.5.1 20.6 20.6.1 20.7 20.7.1 21. 352 355 358 358 359 360 361 Overview ............................................................................................................................................... Memory Map ......................................................................................................................................... Functions to Prevent Rewriting of Flash Memory ................................................................................ ID Code Check Function .................................................................................................................. ROM Code Protect Function ............................................................................................................ CPU Rewrite Mode ............................................................................................................................... Register Description ......................................................................................................................... Status Check Procedure .................................................................................................................... EW0 Mode ........................................................................................................................................ EW1 Mode ........................................................................................................................................ Standard Serial I/O Mode ...................................................................................................................... ID Code Check Function .................................................................................................................. Parallel I/O Mode .................................................................................................................................. ROM Code Protect Function ............................................................................................................ Notes on Flash Memory ........................................................................................................................ CPU Rewrite Mode ........................................................................................................................... 362 363 364 364 365 366 367 373 374 384 392 392 395 395 396 396 Reducing Power Consumption ................................................................................................... 398 21.1 Overview ............................................................................................................................................... 21.2 Key Points and Processing Methods for Reducing Power Consumption ............................................. 21.2.1 Voltage Detection Circuit ................................................................................................................. 21.2.2 Ports .................................................................................................................................................. 21.2.3 Clocks ............................................................................................................................................... 21.2.4 Wait Mode, Stop Mode ..................................................................................................................... 21.2.5 Stopping Peripheral Function Clocks ............................................................................................... 21.2.6 Timers ............................................................................................................................................... 21.2.7 A/D Converter ................................................................................................................................... 21.2.8 Reducing Internal Power Consumption ............................................................................................ 21.2.9 Stopping Flash Memory .................................................................................................................... 21.2.10 Low-Current-Consumption Read Mode ........................................................................................... 398 398 398 398 398 398 398 398 398 399 400 401 22. Electrical Characteristics ............................................................................................................ 402 23. Usage Notes ............................................................................................................................... 423 23.1 Notes on Clock Generation Circuit ....................................................................................................... 423 23.1.1 Stop Mode ......................................................................................................................................... 423 23.1.2 Wait Mode ........................................................................................................................................ 423 23.1.3 Oscillation Stop Detection Function ................................................................................................. 423 23.1.4 Oscillation Circuit Constants ............................................................................................................ 423 A-5 23.2 23.2.1 23.2.2 23.2.3 23.2.4 23.2.5 23.3 23.3.1 23.3.2 23.3.3 23.3.4 23.4 23.5 23.6 23.7 23.7.1 23.8 23.8.1 Notes on Interrupts ................................................................................................................................ 424 Reading Address 00000h .................................................................................................................. 424 SP Setting .......................................................................................................................................... 424 External Interrupt and Key Input Interrupt ....................................................................................... 424 Changing Interrupt Sources .............................................................................................................. 425 Changing Interrupt Control Register Contents ................................................................................. 426 Notes on Timers .................................................................................................................................... 427 Notes on Timer RA ........................................................................................................................... 427 Notes on Timer RB ........................................................................................................................... 428 Notes on Timer RC ........................................................................................................................... 432 Notes on Timer RD ........................................................................................................................... 433 Notes on Serial Interface ....................................................................................................................... 439 Notes on Hardware LIN ........................................................................................................................ 440 Notes on A/D Converter ........................................................................................................................ 441 Notes on Flash Memory ........................................................................................................................ 442 CPU Rewrite Mode ........................................................................................................................... 442 Notes on Noise ...................................................................................................................................... 444 Inserting a Bypass Capacitor between VCC and VSS Pins as a Countermeasure against Noise and Latch-up ........................................................................................................................................... 444 23.8.2 Countermeasures against Noise Error of Port Control Registers ..................................................... 444 24. Notes for On-Chip Debugger ...................................................................................................... 445 Appendix 1. Package Dimensions ........................................................................................................ 446 Appendix 2. Connection Examples between Serial Writer and On-Chip Debugging Emulator ............ 447 Appendix 3. Example of Oscillation Evaluation Circuit ......................................................................... 448 Index ..................................................................................................................................................... 449 A-6 SFR Page Reference Address 0000h 0001h 0002h 0003h 0004h 0005h 0006h 0007h 0008h 0009h 000Ah 000Bh 000Ch 000Dh 000Eh 000Fh 0010h 0011h 0012h 0013h 0014h 0015h 0016h 0017h 0018h 0019h 001Ah 001Bh 001Ch 001Dh 001Eh 001Fh 0020h 0021h 0022h 0023h 0024h 0025h 0026h 0027h 0028h 0029h 002Ah 002Bh 002Ch 002Dh 002Eh 002Fh 0030h 0031h 0032h 0033h 0034h 0035h 0036h 0037h 0038h 0039h 003Ah 003Bh 003Ch 003Dh 003Eh 003Fh NOTE: 1. Register Symbol Page Processor Mode Register 0 Processor Mode Register 1 System Clock Control Register 0 System Clock Control Register 1 PM0 PM1 CM0 CM1 69 69 74 75 Protect Register PRCR 96 Oscillation Stop Detection Register Watchdog Timer Reset Register Watchdog Timer Start Register Watchdog Timer Control Register Address Match Interrupt Register 0 OCD WDTR WDTS WDC RMAD0 76 130 130 130 117 Address Match Interrupt Enable Register Address Match Interrupt Register 1 Count Source Protection Mode Register AIER RMAD1 CSPR 117 117 131 High-Speed On-Chip Oscillator Control Register 0 FRA0 High-Speed On-Chip Oscillator Control Register 1 FRA1 High-Speed On-Chip Oscillator Control Register 2 FRA2 77 77 78 High-Speed On-Chip Oscillator Control Register 6 FRA6 High-Speed On-Chip Oscillator Control Register 7 FRA7 78 78 Voltage Detection Register 1 Voltage Detection Register 2 VCA1 VCA2 35 35, 79 Voltage Monitor 1 Circuit Control Register Voltage Monitor 2 Circuit Control Register Voltage Monitor 0 Circuit Control Register VW1C VW2C VW0C 37 38 36 Address 0040h 0041h 0042h 0043h 0044h 0045h 0046h 0047h 0048h 0049h 004Ah 004Bh 004Ch 004Dh 004Eh 004Fh 0050h 0051h 0052h 0053h 0054h 0055h 0056h 0057h 0058h 0059h 005Ah 005Bh 005Ch 005Dh 005Eh 005Fh 0060h 0061h 0062h 0063h 0064h 0065h 0066h 0067h 0068h 0069h 006Ah 006Bh 006Ch 006Dh 006Eh 006Fh 0070h 0071h 0072h 0073h 0074h 0075h 0076h 0077h 0078h 0079h 007Ah 007Bh 007Ch 007Dh 007Eh 007Fh The blank regions are reserved. Do not access locations in these regions. B-1 Register Symbol Page Timer RC Interrupt Control Register Timer RD0 Interrupt Control Register Timer RD1 Interrupt Control Register TRCIC TRD0IC TRD1IC 103 103 103 UART2 Transmit Interrupt Control Register UART2 Receive Interrupt Control Register Key Input Interrupt Control Register A/D Conversion Interrupt Control Register S2TIC S2RIC KUPIC ADIC 102 102 102 102 UART0 Transmit Interrupt Control Register S0TIC UART0 Receive Interrupt Control Register S0RIC 102 102 Timer RA Interrupt Control Register TRAIC 102 Timer RB Interrupt Control Register INT1 Interrupt Control Register INT3 Interrupt Control Register TRBIC INT1IC INT3IC 102 104 104 INT0 Interrupt Control Register INT0IC 104 Address 0080h 0081h 0082h 0083h 0084h 0085h 0086h 0087h 0088h 0089h 008Ah 008Bh 008Ch 008Dh 008Eh 008Fh 0090h 0091h 0092h 0093h 0094h 0095h 0096h 0097h 0098h 0099h 009Ah 009Bh 009Ch 009Dh 009Eh 009Fh 00A0h 00A1h 00A2h 00A3h 00A4h 00A5h 00A6h 00A7h 00A8h 00A9h 00AAh 00ABh 00ACh 00ADh 00AEh 00AFh 00B0h 00B1h 00B2h 00B3h 00B4h 00B5h 00B6h 00B7h 00B8h 00B9h 00BAh 00BBh 00BCh 00BDh 00BEh 00BFh NOTE: 1. Register UART0 Transmit/Receive Mode Register UART0 Bit Rate Register UART0 Transmit Buffer Register Symbol U0MR U0BRG U0TB UART0 Transmit / Receive Control Register 0 U0C0 UART0 Transmit / Receive Control Register 1 U0C1 UART0 Receive Buffer Register U0RB Page Address 00C0h 00C1h 00C2h 00C3h 00C4h 00C5h 00C6h 00C7h 00C8h 00C9h 00CAh 00CBh 00CCh 00CDh 00CEh 00CFh 00D0h 00D1h 00D2h 00D3h 00D4h 00D5h 00D6h 00D7h 00D8h 00D9h 00DAh 00DBh 00DCh 00DDh 00DEh 00DFh 00E0h 00E1h 00E2h 00E3h 00E4h 00E5h 00E6h 00E7h 00E8h 00E9h 00EAh 00EBh 00ECh 00EDh 00EEh 00EFh 00F0h 00F1h 00F2h 00F3h 00F4h 00F5h 00F6h 00F7h 00F8h 00F9h 00FAh 00FBh 00FCh 00FDh 00FEh 00FFh 318 318 319 319 320 320 The blank regions are reserved. Do not access locations in these regions. B-2 Register Symbol Page 351 A/D Register AD A/D Control Register 2 ADCON2 351 A/D Control Register 0 A/D Control Register 1 ADCON0 ADCON1 350 351 Port P0 Register Port P1 Register Port P0 Direction Register Port P1 Direction Register Port P2 Register Port P3 Register Port P2 Direction Register Port P3 Direction Register Port P4 Register P0 P1 PD0 PD1 P2 P3 PD2 PD3 P4 55 55 54 54 55 55 54 54 55 Port P4 Direction Register PD4 54 Port P2 Drive Capacity Control Register Pin Select Register 1 Pin Select Register 2 Pin Select Register 3 Port Mode Register External Input Enable Register INT Input Filter Select Register Key Input Enable Register Pull-Up Control Register 0 Pull-Up Control Register 1 P2DRR PINSR1 PINSR2 PINSR3 PMR INTEN INTF KIEN PUR0 PUR1 55 56 56 56 56 111 112 115 57 57 Address Register 0100h Timer RA Control Register 0101h Timer RA I/O Control Register Symbol TRACR TRAIOC 0102h 0103h 0104h 0105h 0106h 0107h 0108h 0109h 010Ah Timer RA Mode Register Timer RA Prescaler Register Timer RA Register LIN Control Register 2 LIN Control Register LIN Status Register Timer RB Control Register Timer RB One-Shot Control Register Timer RB I/O Control Register TRAMR TRAPRE TRA LINCR2 LINCR LINST TRBCR TRBOCR TRBIOC 010Bh 010Ch 010Dh 010Eh 010Fh 0110h 0111h 0112h 0113h 0114h 0115h 0116h 0117h Timer RB Mode Register Timer RB Prescaler Register Timer RB Secondary Register Timer RB Primary Register TRBMR TRBPRE TRBSC TRBPR 0118h 0119h 011Ah 011Bh 011Ch 011Dh 011Eh 011Fh 0120h 0121h 0122h 0123h 0124h 0125h 0126h 0127h 0128h 0129h 012Ah 012Bh 012Ch 012Dh 012Eh 012Fh NOTE: 1. Page 137 137, 139, 142, 144, 146, 149 138 138 138 335 335 336 154 154 155, 157, 161, 164, 168 155 156 156 156 Address Register 0130h Timer RC Control Register 2 0131h Timer RC Digital Filter Function Select Register 0132h Timer RC Output Master Enable Register 0133h 0134h 0135h 0136h 0137h Timer RD Start Register TRCMR TRCCR1 Timer RC Interrupt Enable Register Timer RC Status Register Timer RC I/O Control Register 0 Timer RC I/O Control Register 1 Timer RC Counter TRCIER TRCSR TRCIOR0 TRCIOR1 TRC 177 178, 201, 205, 210 179 180 185, 194, 199 185, 195, 200 181 Timer RC General Register A TRCGRA 181 Timer RC General Register B TRCGRB 181 Timer RC General Register C TRCGRC 181 Timer RC General Register D TRCGRD 181 The blank regions are reserved. Do not access locations in these regions. Page 182 183 TRCOER 184 TRDSTR 0138h Timer RD Mode Register TRDMR 0139h 013Ah Timer RD PWM Mode Register Timer RD Function Control Register TRDPMR TRDFCR 013Bh Timer RD Output Master Enable Register 1 TRDOER1 013Ch Timer RD Output Master Enable Register 2 TRDOER2 013Dh 013Eh TRDOCR TRDDF0 TRDDF1 232 0140h Timer RD Output Control Register Timer RD Digital Filter Function Select Register 0 Timer RD Digital Filter Function Select Register 1 Timer RD Control Register 0 229, 243, 260, 273, 283, 297 229, 243, 260, 273, 284, 298 230, 244, 261 231, 245, 262, 274, 285, 299 246, 263, 275, 286, 300 246, 263, 275, 286, 300 247, 264, 301 232 0141h 0142h 0143h Timer RD I/O Control Register A0 Timer RD I/O Control Register C0 Timer RD Status Register 0 0144h Timer RD Interrupt Enable Register 0 0145h Timer RD PWM Mode Output Level Control Register 0 Timer RD Counter 0 013Fh Timer RC Mode Register Timer RC Control Register 1 Symbol TRCCR2 TRCDF 0146h 0147h 0148h 0149h 014Ah 014Bh 014Ch 014Dh 014Eh 014Fh 0150h B-3 233, 248, 264, 276, 287, 302 TRDIORA0 234, 249 TRDIORC0 235, 250 TRDSR0 236, 251, 265, 277, 288, 303 TRDIER0 237, 252, 266, 278, 289, 304 TRDPOCR0 267 TRD0 237, 253, 267, 278, 290, 304 Timer RD General Register A0 TRDGRA0 238, 253, 268, 279, 290, 305 Timer RD General Register B0 TRDGRB0 238, 253, 268, 279, 290, 305 Timer RD General Register C0 TRDGRC0 238, 253, 268, 279, 290, 305 Timer RD General Register D0 TRDGRD0 238, 253, 268, 279, 290, 305 Timer RD Control Register 1 TRDCR1 0151h 0152h 0153h Timer RD I/O Control Register A1 Timer RD I/O Control Register C1 Timer RD Status Register 1 0154h Timer RD Interrupt Enable Register 1 0155h Timer RD PWM Mode Output Level Control Register 1 Timer RD Counter 1 0156h 0157h 0158h 0159h 015Ah 015Bh 015Ch 015Dh 015Eh 015Fh TRDCR0 233, 248, 264, 287 TRDIORA1 234, 249 TRDIORC1 235, 250 TRDSR1 236, 251, 265, 277, 288, 303 TRDIER1 237, 252, 266, 278, 289, 304 TRDPOCR1 267 TRD1 237, 253, 267, 290 Timer RD General Register A1 TRDGRA1 238, 253, 268, 279, 290, 305 Timer RD General Register B1 TRDGRB1 238, 253, 268, 279, 290, 305 Timer RD General Register C1 TRDGRC1 238, 253, 268, 279, 290, 305 Timer RD General Register D1 TRDGRD1 238, 253, 268, 279, 290, 305 Address 0160h 0161h 0162h 0163h 0164h 0165h 0166h 0167h 0168h 0169h 016Ah 016Bh 016Ch 016Dh 016Eh 016Fh 0170h 0171h 0172h 0173h 0174h 0175h 0176h 0177h 0178h 0179h 017Ah 017Bh 017Ch 017Dh 017Eh 017Fh 0180h 0181h 0182h 0183h 0184h 0185h 0186h 0187h 0188h 0189h 018Ah 018Bh 018Ch 018Dh 018Eh 018Fh 0190h 0191h 0192h 0193h 0194h 0195h 0196h 0197h 0198h 0199h 019Ah 019Bh 019Ch 019Dh 019Eh 019Fh NOTE: 1. Register UART2 Transmit/Receive Mode Register UART2 Bit Rate Register UART2 Transmit Buffer Register Symbol U2MR U2BRG U2TB UART2 Transmit/Receive Control Register 0 UART2 Transmit/Receive Control Register 1 UART2 Receive Buffer Register U2C0 U2C1 U2RB Page 318 318 319 319 320 320 Address Register 01A0h 01A1h 01A2h 01A3h 01A4h 01A5h 01A6h 01A7h 01A8h 01A9h 01AAh 01ABh 01ACh 01ADh 01AEh 01AFh 01B0h 01B1h 01B2h 01B3h Flash Memory Control Register 4 01B4h 01B5h Flash Memory Control Register 1 01B6h 01B7h Flash Memory Control Register 0 01B8h 01B9h 01BAh 01BBh 01BCh 01BDh 01BEh 01BFh FFFFh The blank regions are reserved. Do not access locations in these regions. B-4 Option Function Select Register Symbol Page FMR4 371 FMR1 370 FMR0 367 OFS 26, 126, 131, 365 R8C/2K Group, R8C/2L Group RENESAS MCU 1. REJ09B0406-0110 Rev.1.10 Dec 21, 2007 Overview 1.1 Features The R8C/2K Group and R8C/2L Group of single-chip MCUs incorporates the R8C/Tiny Series CPU core, employing sophisticated instructions for a high level of efficiency. With 1 Mbyte of address space, and it is capable of executing instructions at high speed. In addition, the CPU core boasts a multiplier for high-speed operation processing. Power consumption is low, and the supported operating modes allow additional power control. These MCUs also use an anti-noise configuration to reduce emissions of electromagnetic noise and are designed to withstand EMI. Integration of many peripheral functions, including multifunction timer and serial interface, reduces the number of system components. Furthermore, the R8C/2L Group has on-chip data flash (1 KB x 2 blocks). The difference between the R8C/2K Group and R8C/2L Group is only the presence or absence of data flash. Their peripheral functions are the same. 1.1.1 Applications Electronic household appliances, office equipment, audio equipment, consumer equipment, etc. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 1 of 450 R8C/2K Group, R8C/2L Group 1.1.2 1. Overview Specifications Tables 1.1 and 1.2 outlines the Specifications for R8C/2K Group and Tables 1.3 and 1.4 outlines the Specifications for R8C/2L Group. Table 1.1 Item CPU Specifications for R8C/2K Group (1) Function Central processing unit Memory Power Supply Voltage Detection I/O Ports ROM, RAM Voltage detection circuit Clock Clock generation circuits Programmable I/O ports Interrupts Watchdog Timer Timer Timer RA Timer RB Timer RC Timer RD Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Specification R8C/Tiny series core * Number of fundamental instructions: 89 * Minimum instruction execution time: 50 ns (f(XIN) = 20 MHz, VCC = 3.0 to 5.5 V) 100 ns (f(XIN) = 10 MHz, VCC = 2.7 to 5.5 V) 200 ns (f(XIN) = 5 MHz, VCC = 2.2 to 5.5 V) * Multiplier: 16 bits x 16 bits 32 bits * Multiply-accumulate instruction: 16 bits x 16 bits + 32 bits 32 bits * Operation mode: Single-chip mode (address space: 1 Mbyte) Refer to Table 1.5 Product List for R8C/2K Group. * Power-on reset * Voltage detection 3 * Input-only: 3 pins * CMOS I/O ports: 25, selectable pull-up resistor * High current drive ports: 8 2 circuits: XIN clock oscillation circuit (with on-chip feedback resistor), On-chip oscillator (high-speed, low-speed) (high-speed on-chip oscillator has a frequency adjustment function) * Oscillation stop detection: XIN clock oscillation stop detection function * Frequency divider circuit: Dividing selectable 1, 2, 4, 8, and 16 * Low power consumption modes: Standard operating mode (high-speed clock, high-speed on-chip oscillator, low-speed on-chip oscillator), wait mode, stop mode * External: 4 sources, Internal: 15 sources, Software: 4 sources * Priority levels: 7 levels 15 bits x 1 (with prescaler), reset start selectable 8 bits x 1 (with 8-bit prescaler) Timer mode (period timer), pulse output mode (output level inverted every period), event counter mode, pulse width measurement mode, pulse period measurement mode 8 bits x 1 (with 8-bit prescaler) Timer mode (period timer), programmable waveform generation mode (PWM output), programmable one-shot generation mode, programmable wait oneshot generation mode 16 bits x 1 (with 4 capture/compare registers) Timer mode (input capture function, output compare function), PWM mode (output 3 pins), PWM2 mode (PWM output pin) 16 bits x 2 (with 4 capture/compare registers) Timer mode (input capture function, output compare function), PWM mode (output 6 pins), reset synchronous PWM mode (output three-phase waveforms (6 pins), sawtooth wave modulation), complementary PWM mode (output three-phase waveforms (6 pins), triangular wave modulation), PWM3 mode (PWM output 2 pins with fixed period) Page 2 of 450 R8C/2K Group, R8C/2L Group Table 1.2 1. Overview Specifications for R8C/2K Group (2) Item Function Serial UART0, UART2 Interface LIN Module A/D Converter Flash Memory Operating Frequency/Supply Voltage Current consumption Operating Ambient Temperature Package Specification Clock synchronous serial I/O/UART x 2 Hardware LIN: 1 (timer RA, UART0) 10-bit resolution x 9 channels, includes sample and hold function * Programming and erasure voltage: VCC = 2.7 to 5.5 V * Programming and erasure endurance: 100 times * Program security: ROM code protect, ID code check * Debug functions: On-chip debug, on-board flash rewrite function f(XIN) = 20 MHz (VCC = 3.0 to 5.5 V) f(XIN) = 10 MHz (VCC = 2.7 to 5.5 V) f(XIN) = 5 MHz (VCC = 2.2 to 5.5 V) (VCC = 2.7 to 5.5 V for A/D converter only) Typ. 10 mA (VCC = 5.0 V, f(XIN) = 20 MHz) Typ. 6 mA (VCC = 3.0 V, f(XIN) = 10 MHz) Typ. 23 A (VCC = 3.0 V, wait mode, low-speed on-chip oscillator used) Typ. 0.7 A (VCC = 3.0 V, stop mode) -20 to 85C (N version) -40 to 85C (D version)(1) -20 to 105C (Y version)(2) 32-pin LQFP * Package code: PLQP0032GB-A (previous code: 32P6U-A) NOTES: 1. Specify the D version if D version functions are to be used. 2. Please contact Renesas Technology sales offices for the Y version. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 3 of 450 R8C/2K Group, R8C/2L Group Table 1.3 Item CPU 1. Overview Specifications for R8C/2L Group (1) Function Central processing unit Memory Power Supply Voltage Detection I/O Ports ROM, RAM Voltage detection circuit Clock Clock generation circuits Programmable I/O ports Interrupts Watchdog Timer Timer Timer RA Timer RB Timer RC Timer RD Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Specification R8C/Tiny series core * Number of fundamental instructions: 89 * Minimum instruction execution time: 50 ns (f(XIN) = 20 MHz, VCC = 3.0 to 5.5 V) 100 ns (f(XIN) = 10 MHz, VCC = 2.7 to 5.5 V) 200 ns (f(XIN) = 5 MHz, VCC = 2.2 to 5.5 V) * Multiplier: 16 bits x 16 bits 32 bits * Multiply-accumulate instruction: 16 bits x 16 bits + 32 bits 32 bits * Operation mode: Single-chip mode (address space: 1 Mbyte) Refer to Table 1.6 Product List for R8C/2L Group. * Power-on reset * Voltage detection 3 * Input-only: 3 pins * CMOS I/O ports: 25, selectable pull-up resistor * High current drive ports: 8 2 circuits: XIN clock oscillation circuit (with on-chip feedback resistor), On-chip oscillator (high-speed, low-speed) (high-speed on-chip oscillator has a frequency adjustment function) * Oscillation stop detection: XIN clock oscillation stop detection function * Frequency divider circuit: Dividing selectable 1, 2, 4, 8, and 16 * Low power consumption modes: Standard operating mode (high-speed clock, high-speed on-chip oscillator, low-speed on-chip oscillator), wait mode, stop mode * External: 4 sources, Internal: 15 sources, Software: 4 sources * Priority levels: 7 levels 15 bits x 1 (with prescaler), reset start selectable 8 bits x 1 (with 8-bit prescaler) Timer mode (period timer), pulse output mode (output level inverted every period), event counter mode, pulse width measurement mode, pulse period measurement mode 8 bits x 1 (with 8-bit prescaler) Timer mode (period timer), programmable waveform generation mode (PWM output), programmable one-shot generation mode, programmable wait oneshot generation mode 16 bits x 1 (with 4 capture/compare registers) Timer mode (input capture function, output compare function), PWM mode (output 3 pins), PWM2 mode (PWM output pin) 16 bits x 2 (with 4 capture/compare registers) Timer mode (input capture function, output compare function), PWM mode (output 6 pins), reset synchronous PWM mode (output three-phase waveforms (6 pins), sawtooth wave modulation), complementary PWM mode (output three-phase waveforms (6 pins), triangular wave modulation), PWM3 mode (PWM output 2 pins with fixed period) Page 4 of 450 R8C/2K Group, R8C/2L Group Table 1.4 1. Overview Specifications for R8C/2L Group (2) Item Function Serial UART0, UART2 Interface LIN Module A/D Converter Flash Memory Operating Frequency/Supply Voltage Current consumption Operating Ambient Temperature Package Specification Clock synchronous serial I/O/UART x 2 Hardware LIN: 1 (timer RA, UART0) 10-bit resolution x 9 channels, includes sample and hold function * Programming and erasure voltage: VCC = 2.7 to 5.5 V * Programming and erasure endurance: 10,000 times (data flash) 1,000 times (program ROM) * Program security: ROM code protect, ID code check * Debug functions: On-chip debug, on-board flash rewrite function f(XIN) = 20 MHz (VCC = 3.0 to 5.5 V) f(XIN) = 10 MHz (VCC = 2.7 to 5.5 V) f(XIN) = 5 MHz (VCC = 2.2 to 5.5 V) (VCC = 2.7 to 5.5 V for A/D converter only) Typ. 10 mA (VCC = 5.0 V, f(XIN) = 20 MHz) Typ. 6 mA (VCC = 3.0 V, f(XIN) = 10 MHz) Typ. 23 A (VCC = 3.0 V, wait mode, low-speed on-chip oscillator used) Typ. 0.7 A (VCC = 3.0 V, stop mode) -20 to 85C (N version) -40 to 85C (D version)(1) -20 to 105C (Y version)(2) 32-pin LQFP * Package code: PLQP0032GB-A (previous code: 32P6U-A) NOTES: 1. Specify the D version if D version functions are to be used. 2. Please contact Renesas Technology sales offices for the Y version. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 5 of 450 R8C/2K Group, R8C/2L Group 1.2 1. Overview Product List Table 1.5 lists the Product List for R8C/2K Group, Figure 1.1 shows a Part Number, Memory Size, and Package of R8C/2K Group, Table 1.6 lists the Product List for R8C/2L Group, and Figure 1.2 shows a Part Number, Memory Size, and Package of R8C/2L Group. Table 1.5 Product List for R8C/2K Group Part No. R5F212K2SNFP R5F212K4SNFP R5F212K2SDFP R5F212K4SDFP R5F212K2SNXXXFP (D) ROM Capacity 8 Kbytes 16 Kbytes 8 Kbytes 16 Kbytes 8 Kbytes Current of Dec. 2007 RAM Capacity 1 Kbyte 1.5 Kbytes 1 Kbyte 1.5 Kbytes 1 Kbyte Package Type PLQP0032GB-A PLQP0032GB-A PLQP0032GB-A PLQP0032GB-A PLQP0032GB-A R5F212K4SNXXXFP (D) 16 Kbytes 1.5 Kbytes PLQP0032GB-A R5F212K2SDXXXFP (D) 8 Kbytes 1 Kbyte PLQP0032GB-A R5F212K4SDXXXFP (D) 16 Kbytes 1.5 Kbytes PLQP0032GB-A Remarks N version D version N version Factory programming product(1) D version Factory programming product(1) (D): Under development NOTE: 1. The user ROM is programmed before shipment. Part No. R 5 F 21 2K 2 S N XXX FP Package type: FP: PLQP0032GB-A ROM number Classification N: Operating ambient temperature -20C to 85C D: Operating ambient temperature -40C to 85C Y: Operating ambient temperature -20C to 105C (1) S: Low-voltage version ROM capacity 2: 8 KB 4: 16 KB R8C/2K Group R8C/Tiny Series Memory type F: Flash memory Renesas MCU Renesas semiconductor NOTE: 1: Please contact Renesas Technology sales offices for the Y version. Figure 1.1 Part Number, Memory Size, and Package of R8C/2K Group Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 6 of 450 R8C/2K Group, R8C/2L Group Table 1.6 1. Overview Product List for R8C/2L Group Current of Dec. 2007 ROM Capacity Program ROM Data flash R5F212L2SNFP 8 Kbytes 1 Kbyte x 2 R5F212L4SNFP 16 Kbytes 1 Kbyte x 2 R5F212L2SDFP 8 Kbytes 1 Kbyte x 2 R5F212L4SDFP 16 Kbytes 1 Kbyte x 2 R5F212L2SNXXXFP (D) 8 Kbytes 1 Kbyte x 2 RAM Capacity 1 Kbyte 1.5 Kbytes 1 Kbyte 1.5 Kbytes 1 Kbyte R5F212L4SNXXXFP (D) 16 Kbytes 1 Kbyte x 2 1.5 Kbytes R5F212L2SDXXXFP (D) 8 Kbytes 1 Kbyte x 2 1 Kbyte R5F212L4SDXXXFP (D) 16 Kbytes 1 Kbyte x 2 1.5 Kbytes Part No. Package Type Remarks PLQP0032GB-A N version PLQP0032GB-A PLQP0032GB-A D version PLQP0032GB-A PLQP0032GB-A N version Factory PLQP0032GB-A programming product(1) PLQP0032GB-A D version Factory PLQP0032GB-A programming product(1) (D): Under development NOTE: 1. The user ROM is programmed before shipment. Part No. R 5 F 21 2L 2 S N XXX FP Package type: FP: PLQP0032GB-A ROM number Classification N: Operating ambient temperature -20C to 85C D: Operating ambient temperature -40C to 85C Y: Operating ambient temperature -20C to 105C (1) S: Low-voltage version ROM capacity 2: 8 KB 4: 16 KB R8C/2L Group R8C/Tiny Series Memory type F: Flash memory Renesas MCU Renesas semiconductor NOTE: 1: Please contact Renesas Technology sales offices for the Y version. Figure 1.2 Part Number, Memory Size, and Package of R8C/2L Group Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 7 of 450 R8C/2K Group, R8C/2L Group 1.3 1. Overview Block Diagram Figure 1.3 shows a Block Diagram. I/O ports 5 8 8 3 Port P0 Port P1 Port P2 Port P3 1 3 Port P4 Peripheral functions Timers Timer RA (8 bits x 1) Timer RB (8 bits x 1) Timer RC (16 bits x 1) Timer RD (16 bits x 2) UART or clock synchronous serial I/O (8 bits x 2) System clock generation circuit XIN-XOUT High-speed on-chip oscillator Low-speed on-chip oscillator LIN module Watchdog timer (15 bits) A/D converter (10 bits x 9 channels) R8C/Tiny Series CPU core R0H R1H R0L R1L R2 R3 SB ROM(1) USP ISP INTB A0 A1 FB Memory RAM(2) PC FLG Multiplier NOTES: 1. ROM size varies with MCU type. 2. RAM size varies with MCU type. Figure 1.3 Block Diagram Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 8 of 450 R8C/2K Group, R8C/2L Group 1.4 1. Overview Pin Assignment P4_5/INT0 P1_5/RXD0/(TRAIO)/(INT1)(2) P1_6/CLK0 P1_7/TRAIO/INT1 P1_2/KI2/AN10/TRCIOB P1_3/KI3/AN11/TRBO P1_4/TXD0 P1_1/KI1/AN9/TRCIOA/TRCTRG Figure 1.4 shows the Pin Assignment (Top View). Table 1.7 outlines the Pin Name Information by Pin Number. 24 23 22 21 20 19 18 17 16 26 15 14 27 R8C/2K Group R8C/2L Group 28 29 30 13 12 11 PLQP0032GB-A (32P6U-A) (top view) 2 3 4 5 6 10 9 7 8 P3_3/INT3/TRCCLK 1 RESET XOUT/P4_7 (1) VSS/AVSS XIN/P4_6 32 VCC/AVCC 31 MODE P3_5/TRCIOD P0_5/AN2 P0_3/AN4/CLK2 P0_2/AN5/RXD2 P0_1/AN6/TXD2 P0_0/AN7 25 VREF/P4_2 P1_0/KI0/AN8 P3_4/TRCIOC P2_0/TRDIOA0/TRDCLK P2_2/TRDIOC0 P2_1/TRDIOB0 P2_3/TRDIOD0 P2_4/TRDIOA1 P2_5/TRDIOB1 P2_6/TRDIOC1 P2_7/TRDIOD1 NOTES: 1. P4_7 are an input-only port. 2. Can be assigned to the pin in parentheses by a program. 3. Confirm the pin 1 position on the package by referring to the package dimensions. Figure 1.4 Pin Assignment (Top View) Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 9 of 450 R8C/2K Group, R8C/2L Group Table 1.7 Pin Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 1. Overview Pin Name Information by Pin Number Control Pin Port VREF MODE RESET XOUT VSS/AVSS XIN VCC/AVCC P4_2 I/O Pin Functions for of Peripheral Modules Interrupt Timer INT3 TRCCLK TRDIOD1 TRDIOC1 TRDIOB1 TRDIOA1 TRDIOD0 TRDIOB0 TRDIOC0 TRDIOA0/TRDCLK A/D Converter P4_7 P4_6 P3_3 P2_7 P2_6 P2_5 P2_4 P2_3 P2_1 P2_2 P2_0 P4_5 P1_7 P1_6 P1_5 21 22 23 24 P1_4 P1_3 P1_2 P1_1 25 26 P1_0 P3_4 INT0 INT1 TRAIO (INT1)(1) (TRAIO)(1) KI3 KI2 KI1 TRBO TRCIOB TRCIOA/TRCTRG Page 10 of 450 CLK0 RXD0 TXD0 AN11 AN10 AN9 AN8 KI0 TRCIOC 27 P3_5 TRCIOD 28 P0_5 29 P0_3 30 P0_2 31 P0_1 32 P0_0 NOTE: 1. Can be assigned to the pin in parentheses by a program. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Serial Interface CLK2 RXD2 TXD2 AN2 AN4 AN5 AN6 AN7 R8C/2K Group, R8C/2L Group 1.5 1. Overview Pin Functions Table 1.8 lists Pin Functions. Table 1.8 Pin Functions Item Pin Name I/O Type Description Power supply input VCC, VSS - Apply 2.2 V to 5.5 V to the VCC pin. Apply 0 V to the VSS pin. Analog power supply input AVCC, AVSS - Power supply for the A/D converter. Connect a capacitor between AVCC and AVSS. Reset input RESET I Input "L" on this pin resets the MCU. MODE MODE I Connect this pin to VCC via a resistor. XIN clock input XIN I XIN clock output XOUT O These pins are provided for XIN clock generation circuit I/O. Connect a ceramic resonator or a crystal oscillator between the XIN and XOUT pins(1). To use an external clock, input it to the XIN pin and leave the XOUT pin open. INT interrupt input INT0, INT1, INT3 I INT interrupt input pins. INT0 is timer RB, timer RC and timer RD input pins. Key input interrupt KI0 to KI3 I Key input interrupt input pins Timer RA TRAIO I/O Timer RB TRBO O Timer RB output pin Timer RC TRCCLK I External clock input pin TRCTRG Timer RD External trigger input pin TRCIOA, TRCIOB, TRCIOC, TRCIOD I/O Timer RC I/O pins TRDIOA0, TRDIOA1, TRDIOB0, TRDIOB1, TRDIOC0, TRDIOC1, TRDIOD0, TRDIOD1 I/O Timer RD I/O pins TRDCLK Serial interface I Timer RA I/O pin I External clock input pin CLK0, CLK2 I/O RXD0, RXD2 I Serial data input pins Transfer clock I/O pins TXD0, TXD2 O Serial data output pins Reference voltage input VREF I Reference voltage input pin to A/D converter A/D converter AN2, AN4 to AN11 I Analog input pins to A/D converter I/O port P0_0 to P0_3, P0_5, P1_0 to P1_7, P2_0 to P2_7, P3_3 to P3_5, P4_5, Input port P4_2, P4_6, P4_7 I/O I CMOS I/O ports. Each port has an I/O select direction register, allowing each pin in the port to be directed for input or output individually. Any port set to input can be set to use a pull-up resistor or not by a program. P2_0 to P2_7 also function as LED drive ports. Input-only ports I: Input O: Output I/O: Input and output NOTE: 1. Refer to the oscillator manufacturer for oscillation characteristics. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 11 of 450 R8C/2K Group, R8C/2L Group 2. 2. Central Processing Unit (CPU) Central Processing Unit (CPU) Figure 2.1 shows the CPU Registers. The CPU contains 13 registers. R0, R1, R2, R3, A0, A1, and FB configure a register bank. There are two sets of register bank. b31 b15 R2 R3 b8b7 b0 R0H (high-order of R0) R0L (low-order of R0) R1H (high-order of R1) R1L (low-order of R1) Data registers(1) R2 R3 A0 A1 FB b19 b15 Address registers(1) Frame base register(1) b0 Interrupt table register INTBL INTBH The 4 high order bits of INTB are INTBH and the 16 low order bits of INTB are INTBL. b19 b0 Program counter PC b15 b0 USP User stack pointer ISP Interrupt stack pointer SB Static base register b15 b0 FLG b15 b8 IPL b7 Flag register b0 U I O B S Z D C Carry flag Debug flag Zero flag Sign flag Register bank select flag Overflow flag Interrupt enable flag Stack pointer select flag Reserved bit Processor interrupt priority level Reserved bit NOTE: 1. These registers comprise a register bank. There are two register banks. Figure 2.1 CPU Registers Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 12 of 450 R8C/2K Group, R8C/2L Group 2.1 2. Central Processing Unit (CPU) Data Registers (R0, R1, R2, and R3) R0 is a 16-bit register for transfer, arithmetic, and logic operations. The same applies to R1 to R3. R0 can be split into high-order bits (R0H) and low-order bits (R0L) to be used separately as 8-bit data registers. R1H and R1L are analogous to R0H and R0L. R2 can be combined with R0 and used as a 32-bit data register (R2R0). R3R1 is analogous to R2R0. 2.2 Address Registers (A0 and A1) A0 is a 16-bit register for address register indirect addressing and address register relative addressing. It is also used for transfer, arithmetic, and logic operations. A1 is analogous to A0. A1 can be combined with A0 and as a 32bit address register (A1A0). 2.3 Frame Base Register (FB) FB is a 16-bit register for FB relative addressing. 2.4 Interrupt Table Register (INTB) INTB is a 20-bit register that indicates the start address of an interrupt vector table. 2.5 Program Counter (PC) PC is 20 bits wide and indicates the address of the next instruction to be executed. 2.6 User Stack Pointer (USP) and Interrupt Stack Pointer (ISP) The stack pointers (SP), USP, and ISP, are each 16 bits wide. The U flag of FLG is used to switch between USP and ISP. 2.7 Static Base Register (SB) SB is a 16-bit register for SB relative addressing. 2.8 Flag Register (FLG) FLG is an 11-bit register indicating the CPU state. 2.8.1 Carry Flag (C) The C flag retains carry, borrow, or shift-out bits that have been generated by the arithmetic and logic unit. 2.8.2 Debug Flag (D) The D flag is for debugging only. Set it to 0. 2.8.3 Zero Flag (Z) The Z flag is set to 1 when an arithmetic operation results in 0; otherwise to 0. 2.8.4 Sign Flag (S) The S flag is set to 1 when an arithmetic operation results in a negative value; otherwise to 0. 2.8.5 Register Bank Select Flag (B) Register bank 0 is selected when the B flag is 0. Register bank 1 is selected when this flag is set to 1. 2.8.6 Overflow Flag (O) The O flag is set to 1 when an operation results in an overflow; otherwise to 0. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 13 of 450 R8C/2K Group, R8C/2L Group 2.8.7 2. Central Processing Unit (CPU) Interrupt Enable Flag (I) The I flag enables maskable interrupts. Interrupt are disabled when the I flag is set to 0, and are enabled when the I flag is set to 1. The I flag is set to 0 when an interrupt request is acknowledged. 2.8.8 Stack Pointer Select Flag (U) ISP is selected when the U flag is set to 0; USP is selected when the U flag is set to 1. The U flag is set to 0 when a hardware interrupt request is acknowledged or the INT instruction of software interrupt numbers 0 to 31 is executed. 2.8.9 Processor Interrupt Priority Level (IPL) IPL is 3 bits wide and assigns processor interrupt priority levels from level 0 to level 7. If a requested interrupt has higher priority than IPL, the interrupt is enabled. 2.8.10 Reserved Bit If necessary, set to 0. When read, the content is undefined. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 14 of 450 R8C/2K Group, R8C/2L Group 3. 3. Memory Memory 3.1 R8C/2K Group Figure 3.1 is a Memory Map of R8C/2K Group. The R8C/2K Group has 1 Mbyte of address space from addresses 00000h to FFFFFh. The internal ROM is allocated lower addresses, beginning with address 0FFFFh. For example, a 16-Kbyte internal ROM area is allocated addresses 0C000h to 0FFFFh. The fixed interrupt vector table is allocated addresses 0FFDCh to 0FFFFh. They store the starting address of each interrupt routine. The internal RAM is allocated higher addresses beginning with address 00400h. For example, a 1.5-Kbyte internal RAM area is allocated addresses 00400h to 009FFh. The internal RAM is used not only for storing data but also for calling subroutines and as stacks when interrupt requests are acknowledged. Special function registers (SFRs) are allocated addresses 00000h to 002FFh. The peripheral function control registers are allocated here. All addresses within the SFR, which have nothing allocated are reserved for future use and cannot be accessed by users. 00000h 002FFh SFR (Refer to 4. Special Function Registers (SFRs)) 00400h Internal RAM 0XXXh 0FFDCh Undefined instruction Overflow BRK instruction Address match Single step Watchdog timer/oscillation stop detection/voltage monitor 0YYYYh (Reserved) (Reserved) Reset Internal ROM (program ROM) 0FFFFh 0FFFFh FFFFFh NOTE: 1. The blank regions are reserved. Do not access locations in these regions. Part Number R5F212K2SNFP, R5F212K2SDFP, R5F212K2SNXXXFP, R5F212K2SDXXXFP R5F212K4SNFP, R5F212K4SDFP, R5F212K4SNXXXFP, R5F212K4SDXXXFP Figure 3.1 Internal ROM Size Address 0YYYYh Size Address 0XXXXh 8 Kbytes 0E000h 1 Kbyte 007FFh 16 Kbytes 0C000h 1.5 Kbytes 009FFh Memory Map of R8C/2K Group Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 15 of 450 Internal RAM R8C/2K Group, R8C/2L Group 3.2 3. Memory R8C/2L Group Figure 3.2 is a Memory Map of R8C/2L Group. The R8C/2L Group has 1 Mbyte of address space from addresses 00000h to FFFFFh. The internal ROM (program ROM) is allocated lower addresses, beginning with address 0FFFFh. For example, a 16-Kbyte internal ROM area is allocated addresses 0C000h to 0FFFFh. The fixed interrupt vector table is allocated addresses 0FFDCh to 0FFFFh. They store the starting address of each interrupt routine. The internal ROM (data flash) is allocated addresses 02400h to 02BFFh. The internal RAM area is allocated higher addresses, beginning with address 00400h. For example, a 1.5-Kbyte internal RAM is allocated addresses 00400h to 009FFh. The internal RAM is used not only for storing data but also for calling subroutines and as stacks when interrupt requests are acknowledged. Special function registers (SFRs) are allocated addresses 00000h to 002FFh. The peripheral function control registers are allocated here. All addresses within the SFR, which have nothing allocated are reserved for future use and cannot be accessed by users. 00000h 002FFh SFR (Refer to 4. Special Function Registers (SFRs)) 00400h Internal RAM 0XXXXh 02400h 0FFDCh Internal ROM (data flash)(1) 02BFFh Undefined instruction Overflow BRK instruction Address match Single step 0YYYYh Watchdog timer/oscillation stop detection/voltage monitor (Reserved) (Reserved) Reset Internal ROM (program ROM) 0FFFFh 0FFFFh FFFFFh NOTES: 1. Data flash block A (1 Kbyte) and B (1 Kbyte) are shown. 2. The blank regions are reserved. Do not access locations in these regions. R5F212L2SNFP, R5F212L2SDFP, R5F212L2SNXXXFP, R5F212L2SDXXXFP R5F212L4SNFP, R5F212L4SDFP, R5F212L4SNXXXFP, R5F212L4SDXXXFP Figure 3.2 Size Address 0YYYYh Size Address 0XXXXh 8 Kbytes 0E000h 1 Kbyte 007FFh 16 Kbytes 0C000h 1.5 Kbytes 009FFh Memory Map of R8C/2L Group Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 16 of 450 Internal RAM Internal ROM Part Number R8C/2K Group, R8C/2L Group 4. 4. Special Function Registers (SFRs) Special Function Registers (SFRs) An SFR (special function register) is a control register for a peripheral function. Tables 4.1 to 4.7 list the special function registers. Table 4.1 Address 0000h 0001h 0002h 0003h 0004h 0005h 0006h 0007h 0008h 0009h 000Ah 000Bh 000Ch 000Dh 000Eh 000Fh 0010h 0011h 0012h 0013h 0014h 0015h 0016h 0017h 0018h 0019h 001Ah 001Bh 001Ch SFR Information (1)(1) Register Symbol After reset Processor Mode Register 0 Processor Mode Register 1 System Clock Control Register 0 System Clock Control Register 1 PM0 PM1 CM0 CM1 00h 00h 01101000b 00100000b Protect Register PRCR 00h Oscillation Stop Detection Register Watchdog Timer Reset Register Watchdog Timer Start Register Watchdog Timer Control Register Address Match Interrupt Register 0 OCD WDTR WDTS WDC RMAD0 Address Match Interrupt Enable Register Address Match Interrupt Register 1 AIER RMAD1 00000100b XXh XXh 00X11111b 00h 00h 00h 00h 00h 00h 00h Count Source Protection Mode Register CSPR 00h 10000000b(6) High-Speed On-Chip Oscillator Control Register 0 High-Speed On-Chip Oscillator Control Register 1 High-Speed On-Chip Oscillator Control Register 2 FRA0 FRA1 FRA2 00h When shipping 00h High-Speed On-Chip Oscillator Control Register 6 High-Speed On-Chip Oscillator Control Register 7 FRA6 FRA7 When Shipping When Shipping 0030h 0031h 0032h Voltage Detection Register 1(2) Voltage Detection Register 2(2) VCA1 VCA2 00001000b 00h(3) 00100000b(4) 0033h 0034h 0035h 0036h 0037h 0038h Voltage Monitor 1 Circuit Control Register(5) Voltage Monitor 2 Circuit Control Register(5) Voltage Monitor 0 Circuit Control Register(2) VW1C VW2C VW0C 00001000b 00h 0000X000b(3) 0100X001b(4) 001Dh 001Eh 001Fh 0020h 0021h 0022h 0023h 0024h 0025h 0026h 0027h 0028h 0029h 002Ah 002Bh 002Ch 0039h 003Ah 003Eh 003Fh X: Undefined NOTES: 1. The blank regions are reserved. Do not access locations in these regions. 2. Software reset, watchdog timer reset, voltage monitor 1 reset, or voltage monitor 2 reset do not affect this register. 3. The LVD0ON bit in the OFS register is set to 1 and hardware reset. 4. Power-on reset, voltage monitor 0 reset, or the LVD0ON bit in the OFS register is set to 0 and hardware reset. 5. Software reset, watchdog timer reset, voltage monitor 1 reset, or voltage monitor 2 reset do not affect b2 and b3. 6. The CSPROINI bit in the OFS register is set to 0. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 17 of 450 R8C/2K Group, R8C/2L Group Table 4.2 Address 0040h 0041h 0042h 0043h 0044h 0045h 0046h 0047h 0048h 0049h 004Ah 004Bh 004Ch 004Dh 004Eh 004Fh 0050h 0051h 0052h 0053h 0054h 0055h 0056h 0057h 0058h 0059h 005Ah 005Bh 005Ch 005Dh 005Eh 005Fh 0060h 0061h 0062h 0063h 0064h 0065h 0066h 0067h 0068h 0069h 006Ah 006Bh 006Ch 006Dh 006Eh 006Fh 0070h 0071h 0072h 0073h 0074h 0075h 0076h 0077h 0078h 0079h 007Ah 007Bh 007Ch 007Dh 007Eh 007Fh 4. Special Function Registers (SFRs) SFR Information (2)(1) Register Symbol After reset Timer RC Interrupt Control Register Timer RD0 Interrupt Control Register Timer RD1 Interrupt Control Register TRCIC TRD0IC TRD1IC XXXXX000b XXXXX000b XXXXX000b UART2 Transmit Interrupt Control Register UART2 Receive Interrupt Control Register Key Input Interrupt Control Register A/D Conversion Interrupt Control Register S2TIC S2RIC KUPIC ADIC XXXXX000b XXXXX000b XXXXX000b XXXXX000b UART0 Transmit Interrupt Control Register UART0 Receive Interrupt Control Register S0TIC S0RIC XXXXX000b XXXXX000b Timer RA Interrupt Control Register TRAIC XXXXX000b Timer RB Interrupt Control Register INT1 Interrupt Control Register INT3 Interrupt Control Register TRBIC INT1IC INT3IC XXXXX000b XX00X000b XX00X000b INT0 Interrupt Control Register INT0IC XX00X000b X: Undefined NOTE: 1. The blank regions are reserved. Do not access locations in these regions. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 18 of 450 R8C/2K Group, R8C/2L Group Table 4.3 Address 0080h 0081h 0082h 0083h 0084h 0085h 0086h 0087h 0088h 0089h 008Ah 008Bh 008Ch 008Dh 008Eh 008Fh 0090h 0091h 0092h 0093h 0094h 0095h 0096h 0097h 0098h 0099h 009Ah 009Bh 009Ch 009Dh 009Eh 009Fh 00A0h 00A1h 00A2h 00A3h 00A4h 00A5h 00A6h 00A7h 00A8h 00A9h 00AAh 00ABh 00ACh 00ADh 00AEh 00AFh 00B0h 00B1h 00B2h 00B3h 00B4h 00B5h 00B6h 00B7h 00B8h 00B9h 00BAh 00BBh 00BCh 00BDh 00BEh 00BFh 4. Special Function Registers (SFRs) SFR Information (3)(1) Register Symbol UART0 Transmit/Receive Mode Register UART0 Bit Rate Register UART0 Transmit Buffer Register U0MR U0BRG U0TB UART0 Transmit/Receive Control Register 0 UART0 Transmit/Receive Control Register 1 UART0 Receive Buffer Register U0C0 U0C1 U0RB X: Undefined NOTE: 1. The blank regions are reserved. Do not access locations in these regions. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 19 of 450 After reset 00h XXh XXh XXh 00001000b 00000010b XXh XXh R8C/2K Group, R8C/2L Group Table 4.4 Address 00C0h 00C1h 00C2h 00C3h 00C4h 00C5h 00C6h 00C7h 00C8h 00C9h 00CAh 00CBh 00CCh 00CDh 00CEh 00CFh 00D0h 00D1h 00D2h 00D3h 00D4h 00D5h 00D6h 00D7h 00D8h 00D9h 00DAh 00DBh 00DCh 00DDh 00DEh 00DFh 00E0h 00E1h 00E2h 00E3h 00E4h 00E5h 00E6h 00E7h 00E8h 00E9h 00EAh 00EBh 00ECh 00EDh 00EEh 00EFh 00F0h 00F1h 00F2h 00F3h 00F4h 00F5h 00F6h 00F7h 00F8h 00F9h 00FAh 00FBh 00FCh 00FDh 00FEh 00FFh 4. Special Function Registers (SFRs) SFR Information (4)(1) Register Symbol After reset A/D Register AD XXh XXh A/D Control Register 2 ADCON2 00h A/D Control Register 0 A/D Control Register 1 ADCON0 ADCON1 00h 00h Port P0 Register Port P1 Register Port P0 Direction Register Port P1 Direction Register Port P2 Register Port P3 Register Port P2 Direction Register Port P3 Direction Register Port P4 Register P0 P1 PD0 PD1 P2 P3 PD2 PD3 P4 XXh XXh 00h 00h XXh XXh 00h 00h XXh Port P4 Direction Register PD4 00h Port P2 Drive Capacity Control Register Pin Select Register 1 Pin Select Register 2 Pin Select Register 3 Port Mode Register External Input Enable Register INT Input Filter Select Register Key Input Enable Register Pull-Up Control Register 0 Pull-Up Control Register 1 P2DRR PINSR1 PINSR2 PINSR3 PMR INTEN INTF KIEN PUR0 PUR1 00h XXh XXh XXh 00h 00h 00h 00h 00h XX000000b X: Undefined NOTE: 1. The blank regions are reserved. Do not access locations in these regions. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 20 of 450 R8C/2K Group, R8C/2L Group Table 4.5 Address 0100h 0101h 0102h 0103h 0104h 0105h 0106h 0107h 0108h 0109h 010Ah 010Bh 010Ch 010Dh 010Eh 010Fh 0110h 0111h 0112h 0113h 0114h 0115h 0116h 0117h 0118h 0119h 011Ah 011Bh 011Ch 011Dh 011Eh 011Fh 0120h 0121h 0122h 0123h 0124h 0125h 0126h 0127h 0128h 0129h 012Ah 012Bh 012Ch 012Dh 012Eh 012Fh 0130h 0131h 0132h 0133h 0134h 0135h 0136h 0137h 0138h 0139h 013Ah 013Bh 013Ch 013Dh 013Eh 013Fh NOTE: 1. 4. Special Function Registers (SFRs) SFR Information (5)(1) Timer RA Control Register Timer RA I/O Control Register Timer RA Mode Register Timer RA Prescaler Register Timer RA Register LIN Control Register 2 LIN Control Register LIN Status Register Timer RB Control Register Timer RB One-Shot Control Register Timer RB I/O Control Register Timer RB Mode Register Timer RB Prescaler Register Timer RB Secondary Register Timer RB Primary Register Register Symbol TRACR TRAIOC TRAMR TRAPRE TRA LINCR2 LINCR LINST TRBCR TRBOCR TRBIOC TRBMR TRBPRE TRBSC TRBPR Timer RC Mode Register Timer RC Control Register 1 Timer RC Interrupt Enable Register Timer RC Status Register Timer RC I/O Control Register 0 Timer RC I/O Control Register 1 Timer RC Counter TRCMR TRCCR1 TRCIER TRCSR TRCIOR0 TRCIOR1 TRC Timer RC General Register A TRCGRA Timer RC General Register B TRCGRB Timer RC General Register C TRCGRC Timer RC General Register D TRCGRD Timer RC Control Register 2 Timer RC Digital Filter Function Select Register Timer RC Output Master Enable Register TRCCR2 TRCDF TRCOER 01001000b 00h 01110000b 01110000b 10001000b 10001000b 00h 00h FFh FFh FFh FFh FFh FFh FFh FFh 00011111b 00h 01111111b Timer RD Start Register Timer RD Mode Register Timer RD PWM Mode Register Timer RD Function Control Register Timer RD Output Master Enable Register 1 Timer RD Output Master Enable Register 2 Timer RD Output Control Register Timer RD Digital Filter Function Select Register 0 Timer RD Digital Filter Function Select Register 1 TRDSTR TRDMR TRDPMR TRDFCR TRDOER1 TRDOER2 TRDOCR TRDDF0 TRDDF1 11111100b 00001110b 10001000b 10000000b FFh 01111111b 00h 00h 00h The blank regions are reserved. Do not access locations in these regions Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 21 of 450 After reset 00h 00h 00h FFh FFh 00h 00h 00h 00h 00h 00h 00h FFh FFh FFh R8C/2K Group, R8C/2L Group Table 4.6 Address 0140h 0141h 0142h 0143h 0144h 0145h 0146h 0147h 0148h 0149h 014Ah 014Bh 014Ch 014Dh 014Eh 014Fh 0150h 0151h 0152h 0153h 0154h 0155h 0156h 0157h 0158h 0159h 015Ah 015Bh 015Ch 015Dh 015Eh 015Fh 0160h 0161h 0162h 0163h 0164h 0165h 0166h 0167h 0168h 0169h 016Ah 016Bh 016Ch 016Dh 016Eh 016Fh 0170h 0171h 0172h 0173h 0174h 0175h 0176h 0177h 0178h 0179h 017Ah 017Bh 017Ch 017Dh 017Eh 017Fh 4. Special Function Registers (SFRs) SFR Information (6)(1) Register Timer RD Control Register 0 Timer RD I/O Control Register A0 Timer RD I/O Control Register C0 Timer RD Status Register 0 Timer RD Interrupt Enable Register 0 Timer RD PWM Mode Output Level Control Register 0 Timer RD Counter 0 Symbol TRDCR0 TRDIORA0 TRDIORC0 TRDSR0 TRDIER0 TRDPOCR0 TRD0 Timer RD General Register A0 TRDGRA0 Timer RD General Register B0 TRDGRB0 Timer RD General Register C0 TRDGRC0 Timer RD General Register D0 TRDGRD0 Timer RD Control Register 1 Timer RD I/O Control Register A1 Timer RD I/O Control Register C1 Timer RD Status Register 1 Timer RD Interrupt Enable Register 1 Timer RD PWM Mode Output Level Control Register 1 Timer RD Counter 1 TRDCR1 TRDIORA1 TRDIORC1 TRDSR1 TRDIER1 TRDPOCR1 TRD1 Timer RD General Register A1 TRDGRA1 Timer RD General Register B1 TRDGRB1 Timer RD General Register C1 TRDGRC1 Timer RD General Register D1 TRDGRD1 UART2 Transmit/Receive Mode Register UART2 Bit Rate Register UART2 Transmit Buffer Register U2MR U2BRG U2TB UART2 Transmit/Receive Control Register 0 UART2 Transmit/Receive Control Register 1 UART2 Receive Buffer Register U2C0 U2C1 U2RB X: Undefined NOTE: 1. The blank regions are reserved. Do not access locations in these regions. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 22 of 450 After reset 00h 10001000b 10001000b 11100000b 11100000b 11111000b 00h 00h FFh FFh FFh FFh FFh FFh FFh FFh 00h 10001000b 10001000b 11000000b 11100000b 11111000b 00h 00h FFh FFh FFh FFh FFh FFh FFh FFh 00h XXh XXh XXh 00001000b 00000010b XXh XXh R8C/2K Group, R8C/2L Group Table 4.7 Address 0180h 0181h 0182h 0183h 0184h 0185h 0186h 0187h 0188h 0189h 018Ah 018Bh 018Ch 018Dh 018Eh 018Fh 0190h 0191h 0192h 0193h 0194h 0195h 0196h 0197h 0198h 0199h 019Ah 019Bh 019Ch 019Dh 019Eh 019Fh 01A0h 01A1h 01A2h 01A3h 01A4h 01A5h 01A6h 01A7h 01A8h 01A9h 01AAh 01ABh 01ACh 01ADh 01AEh 01AFh 01B0h 01B1h 01B2h 01B3h 01B4h 01B5h 01B6h 01B7h 01B8h 01B9h 01BAh 01BBh 01BCh 01BDh 01BEh 01BFh FFFFh 4. Special Function Registers (SFRs) SFR Information (7)(1) Register Symbol After reset Flash Memory Control Register 4 FMR4 01000000b Flash Memory Control Register 1 FMR1 1000000Xb Flash Memory Control Register 0 FMR0 00000001b Option Function Select Register OFS (Note 2) X: Undefined NOTES: 1. The blank regions are reserved. Do not access locations in these regions. 2. The OFS register cannot be changed by a program. Use a flash programmer to write to it. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 23 of 450 R8C/2K Group, R8C/2L Group 5. 5. Resets Resets The following resets are implemented: hardware reset, power-on reset, voltage monitor 0 reset, voltage monitor 1 reset, voltage monitor 2 reset, watchdog timer reset, and software reset. Table 5.1 lists the Reset Names and Sources. Table 5.1 Reset Names and Sources Reset Name Source Hardware reset Power-on reset Voltage monitor 0 reset Voltage monitor 1 reset Voltage monitor 2 reset Watchdog timer reset Software reset Input voltage of RESET pin is held "L" VCC rises VCC falls (monitor voltage: Vdet0) VCC falls (monitor voltage: Vdet1) VCC falls (monitor voltage: Vdet2) Underflow of watchdog timer Write 1 to PM03 bit in PM0 register Hardware reset RESET SFRs Bits VCA25, VW0C0, and VW0C6 SFRs Power-on reset circuit VCC Bits VCA25, VW0C0, and VW0C6 Power-on reset Voltage monitor 0 reset Voltage detection circuit Voltage monitor 1 reset Voltage monitor 2 reset Watchdog timer CPU SFRs Bits VCA13, VCA26, VCA27, VW1C2, VW1C3, VW2C2, VW2C3, VW0C1, VW0F0, VW0F1, and VW0C7 Watchdog timer reset Pin, CPU, and SFR bits other than those listed above Software reset VCA13: Bit in VCA1 register VCA25, VCA26, VCA27: Bits in VCA2 register VW0C0, VW0C1, VW0C6, VW0F0, VW0F1, VW0C7: Bits in VW0C register VW1C2, VW1C3: Bits in VW1C register VW2C2, VW2C3: Bits in VW2C register Figure 5.1 Block Diagram of Reset Circuit Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 24 of 450 R8C/2K Group, R8C/2L Group 5. Resets Table 5.2 shows the Pin Functions while RESET Pin Level is "L", Figure 5.2 shows the CPU Register Status after Reset, Figure 5.3 shows the Reset Sequence, and Figure 5.4 shows the OFS Register. Table 5.2 Pin Functions while RESET Pin Level is "L" Pin Name P0_0 to P0_3, P0_5 P1, P2 P3_3 to P3_5 P4_2, P4_5 to P4_7 Pin Functions Input port Input port Input port Input port b15 b0 0000h Data register(R0) 0000h Data register(R1) 0000h Data register(R2) 0000h 0000h 0000h 0000h Data register(R3) b19 Address register(A0) Address register(A1) Frame base register(FB) b0 00000h Content of addresses 0FFFEh to 0FFFCh b15 Interrupt table register(INTB) Program counter(PC) b0 0000h User stack pointer(USP) 0000h Interrupt stack pointer(ISP) 0000h Static base register(SB) b15 b0 Flag register(FLG) 0000h b15 b8 IPL Figure 5.2 b7 b0 U I O B S Z D C CPU Register Status after Reset fOCO-S RESET pin 10 cycles or more are needed(1) fOCO-S clock x 32 cycles(2) Internal reset signal Start time of flash memory (CPU clock x 14 cycles) CPU clock x 28 cycles CPU clock 0FFFCh 0FFFEh Address (internal address signal) 0FFFDh Content of reset vector NOTES: 1. Hardware reset. 2. When the "L" input width to the RESET pin is set to fOCO-S clock x 32 cycles or more, setting the RESET pin to "H" also sets the internal reset signal to "H" at the same. Figure 5.3 Reset Sequence Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 25 of 450 R8C/2K Group, R8C/2L Group 5. Resets Option Function Select Register(1) b7 b6 b5 b4 b3 b2 b1 b0 1 1 1 Symbol OFS Bit Symbol WDTON -- (b1) ROMCR ROMCP1 -- (b4) LVD0ON -- (b6) Address 0FFFFh Bit Name Watchdog timer start select bit When Shipping FFh(3) Function 0 : Starts w atchdog timer automatically after reset 1 : Watchdog timer is inactive after reset Reserved bit Set to 1. ROM code protect disabled bit 0 : ROM code protect disabled 1 : ROMCP1 enabled RW ROM code protect bit 0 : ROM code protect enabled 1 : ROM code protect disabled RW Reserved bit Set to 1. Voltage detection 0 circuit start bit(2) 0 : Voltage monitor 0 reset enabled after hardw are reset 1 : Voltage monitor 0 reset disabled after hardw are reset Reserved bit Set to 1. Count source protect CSPROINI mode after reset select bit 0 : Count source protect mode enabled after reset 1 : Count source protect mode disabled after reset RW RW RW RW RW RW RW NOTES: 1. The OFS register is on the flash memory. Write to the OFS register w ith a program. After w riting is completed, do not w rite additions to the OFS register. 2. Setting the LVD0ON bit is only valid after a hardw are reset. To use the pow er-on reset, set the LVD0ON bit to 0 (voltage monitor 0 reset enabled after hardw are reset). 3. If the block including the OFS register is erased, FFh is set to the OFS register. Figure 5.4 OFS Register Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 26 of 450 R8C/2K Group, R8C/2L Group 5.1 5. Resets Hardware Reset A reset is applied using the RESET pin. When an "L" signal is applied to the RESET pin while the supply voltage meets the recommended operating conditions, pins, CPU, and SFRs are all reset (refer to Table 5.2 Pin Functions while RESET Pin Level is "L"). When the input level applied to the RESET pin changes from "L" to "H", a program is executed beginning with the address indicated by the reset vector. After reset, the low-speed on-chip oscillator clock divided by 8 is automatically selected as the CPU clock. Refer to 4. Special Function Registers (SFRs) for the state of the SFRs after reset. The internal RAM is not reset. If the RESET pin is pulled "L" while writing to the internal RAM is in progress, the contents of internal RAM will be undefined. Figure 5.5 shows an Example of Hardware Reset Circuit and Operation and Figure 5.6 shows an Example of Hardware Reset Circuit (Usage Example of External Supply Voltage Detection Circuit) and Operation. 5.1.1 When Power Supply is Stable (1) Apply "L" to the RESET pin. (2) Wait for 10 s. (3) Apply "H" to the RESET pin. 5.1.2 Power On (1) Apply "L" to the RESET pin. (2) Let the supply voltage increase until it meets the recommended operating conditions. (3) Wait for td(P-R) or more to allow the internal power supply to stabilize (refer to 22. Electrical Characteristics). (4) Wait for 10 s. (5) Apply "H" to the RESET pin. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 27 of 450 R8C/2K Group, R8C/2L Group 5. Resets VCC 2.2 V VCC 0V RESET RESET 0.2 VCC or below 0V td(P-R) + 10s or more NOTE: 1. Refer to 22. Electrical Characteristics. Figure 5.5 Example of Hardware Reset Circuit and Operation Supply voltage detection circuit RESET 5V VCC 2.2 V VCC 0V 5V RESET 0V td(P-R) + 10s or more Example when VCC = 5 V NOTE: 1. Refer to 22. Electrical Characteristics. Figure 5.6 Example of Hardware Reset Circuit (Usage Example of External Supply Voltage Detection Circuit) and Operation Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 28 of 450 R8C/2K Group, R8C/2L Group 5.2 5. Resets Power-On Reset Function When the RESET pin is connected to the VCC pin via a pull-up resistor, and the VCC pin voltage level rises while the rise gradient is trth or more, the power-on reset function is enabled and the MCU resets its pins, CPU, and SFR. When a capacitor is connected to the RESET pin, too, always keep the voltage to the RESET pin 0.8VCC or more. When the input voltage to the VCC pin reaches the Vdet0 level or above, the low-speed on-chip oscillator clock starts counting. When the low-speed on-chip oscillator clock count reaches 32, the internal reset signal is held "H" and the MCU enters the reset sequence (refer to Figure 5.3). The low-speed on-chip oscillator clock divided by 8 is automatically selected as the CPU clock after reset. Refer to 4. Special Function Registers (SFRs) for the states of the SFR after power-on reset. The voltage monitor 0 reset is enabled after power-on reset. Figure 5.7 shows an Example of Power-On Reset Circuit and Operation. VCC 4.7 k (reference) RESET Vdet0(3) Vdet0(3) 2.2V trth trth External Power VCC Vpor2 Vpor1 Sampling time(1, 2) tw(por1) Internal reset signal ("L" valid) 1 x 32 fOCO-S 1 x 32 fOCO-S NOTES: 1. When using the voltage monitor 0 digital filter, ensure that the voltage is within the MCU operation voltage range (2.2 V or above) during the sampling time. 2. The sampling clock can be selected. Refer to 6. Voltage Detection Circuit for details. 3. Vdet0 indicates the voltage detection level of the voltage detection 0 circuit. Refer to 6. Voltage Detection Circuit for details. 4. Refer to 22. Electrical Characteristics. 5. To use the power-on reset function, enable voltage monitor 0 reset by setting the LVD0ON bit in the OFS register to 0, the VW0C0 and VW0C6 bits in the VW0C register to 1 respectively, and the VCA25 bit in the VCA2 register to 1. Figure 5.7 Example of Power-On Reset Circuit and Operation Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 29 of 450 R8C/2K Group, R8C/2L Group 5.3 5. Resets Voltage Monitor 0 Reset A reset is applied using the on-chip voltage detection 0 circuit. The voltage detection 0 circuit monitors the input voltage to the VCC pin. The voltage to monitor is Vdet0. When the input voltage to the VCC pin reaches the Vdet0 level or below, the pins, CPU, and SFR are reset. When the input voltage to the VCC pin reaches the Vdet0 level or above, the low-speed on-chip oscillator clock start counting. When the low-speed on-chip oscillator clock count reaches 32, the internal reset signal is held "H" and the MCU enters the reset sequence (refer to Figure 5.3). The low-speed on-chip oscillator clock divided by 8 is automatically selected as the CPU clock after reset. The LVD0ON bit in the OFS register can be used to enable or disable voltage monitor 0 reset after a hardware reset. Setting the LVD0ON bit is only valid after a hardware reset. To use the power-on reset function, enable voltage monitor 0 reset by setting the LVD0ON bit in the OFS register to 0, the VW0C0 and VW0C6 bits in the VW0C register to 1 respectively, and the VCA25 bit in the VCA2 register to 1. The LVD0ON bit cannot be changed by a program. To set the LVD0ON bit, write 0 (voltage monitor 0 reset enabled after hardware reset) or 1 (voltage monitor 0 reset disabled after hardware reset) to bit 5 of address 0FFFFh using a flash programmer. Refer to Figure 5.4 OFS Register for details of the OFS register. Refer to 4. Special Function Registers (SFRs) for the status of the SFR after voltage monitor 0 reset. The internal RAM is not reset. When the input voltage to the VCC pin reaches the Vdet0 level or below while writing to the internal RAM is in progress, the contents of internal RAM are undefined. Refer to 6. Voltage Detection Circuit for details of voltage monitor 0 reset. 5.4 Voltage Monitor 1 Reset A reset is applied using the on-chip voltage detection 1 circuit. The voltage detection 1 circuit monitors the input voltage to the VCC pin. The voltage to monitor is Vdet1. When the input voltage to the VCC pin reaches the Vdet1 level or below, the pins, CPU, and SFR are reset and a program is executed beginning with the address indicated by the reset vector. After reset, the low-speed on-chip oscillator clock divided by 8 is automatically selected as the CPU clock. The voltage monitor 1 does not reset some portions of the SFR. Refer to 4. Special Function Registers (SFRs) for details. The internal RAM is not reset. When the input voltage to the VCC pin reaches the Vdet1 level or below while writing to the internal RAM is in progress, the contents of internal RAM are undefined. Refer to 6. Voltage Detection Circuit for details of voltage monitor 1 reset. 5.5 Voltage Monitor 2 Reset A reset is applied using the on-chip voltage detection 2 circuit. The voltage detection 2 circuit monitors the input voltage to the VCC pin. The voltage to monitor is Vdet2. When the input voltage to the VCC pin reaches the Vdet2 level or below, the pins, CPU, and SFR are reset and the program beginning with the address indicated by the reset vector is executed. After reset, the low-speed on-chip oscillator clock divided by 8 is automatically selected as the CPU clock. The voltage monitor 2 does not reset some SFRs. Refer to 4. Special Function Registers (SFRs) for details. The internal RAM is not reset. When the input voltage to the VCC pin reaches the Vdet2 level or below while writing to the internal RAM is in progress, the contents of internal RAM are undefined. Refer to 6. Voltage Detection Circuit for details of voltage monitor 2 reset. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 30 of 450 R8C/2K Group, R8C/2L Group 5.6 5. Resets Watchdog Timer Reset When the PM12 bit in the PM1 register is set to 1 (reset when watchdog timer underflows), the MCU resets its pins, CPU, and SFR if the watchdog timer underflows. Then the program beginning with the address indicated by the reset vector is executed. After reset, the low-speed on-chip oscillator clock divided by 8 is automatically selected as the CPU clock. The watchdog timer reset does not reset some SFRs. Refer to 4. Special Function Registers (SFRs) for details. The internal RAM is not reset. When the watchdog timer underflows, the contents of internal RAM are undefined. Refer to 15. Watchdog Timer for details of the watchdog timer. 5.7 Software Reset When the PM03 bit in the PM0 register is set to 1 (MCU reset), the MCU resets its pins, CPU, and SFR. The program beginning with the address indicated by the reset vector is executed. After reset, the low-speed on-chip oscillator clock divided by 8 is automatically selected for the CPU clock. The software reset does not reset some SFRs. Refer to 4. Special Function Registers (SFRs) for details. The internal RAM is not reset. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 31 of 450 R8C/2K Group, R8C/2L Group 6. 6. Voltage Detection Circuit Voltage Detection Circuit The voltage detection circuit monitors the input voltage to the VCC pin. This circuit can be used to monitor the VCC input voltage by a program. Alternately, voltage monitor 0 reset, voltage monitor 1 interrupt, voltage monitor 1 reset, voltage monitor 2 interrupt, and voltage monitor 2 reset can also be used. Table 6.1 lists the Specifications of Voltage Detection Circuit and Figures 6.1 to 6.4 show the Block Diagrams. Figures 6.5 to 6.8 show the Associated Registers. Table 6.1 VCC Monitor Specifications of Voltage Detection Circuit Item Voltage to monitor Detection target Monitor Process Reset When Voltage is Detected Voltage monitor 0 reset Reset at Vdet0 > VCC; restart CPU operation at VCC > Vdet0 None Interrupt Digital Filter Switch enabled/disabled Sampling time Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Voltage Detection 0 Vdet0 Whether passing through Vdet0 by rising or falling None Available Voltage Detection 1 Voltage Detection 2 Vdet1 Vdet2 Passing through Vdet1 by Passing through Vdet2 by rising or falling rising or falling VW1C3 bit in VW1C register Whether VCC is higher or lower than Vdet1 Voltage monitor 1 reset Reset at Vdet1 > VCC; restart CPU operation after a specified time Voltage monitor 1 interrupt Interrupt request at Vdet1 > VCC and VCC > Vdet1 when digital filter is enabled; interrupt request at Vdet1 > VCC or VCC > Vdet1 when digital filter is disabled Available (Divide-by-n of fOCO-S) (Divide-by-n of fOCO-S) x4 x4 n: 1, 2, 4, and 8 n: 1, 2, 4, and 8 Page 32 of 450 VCA13 bit in VCA1 register Whether VCC is higher or lower than Vdet2 Voltage monitor 2 reset Reset at Vdet2 > VCC; restart CPU operation after a specified time Voltage monitor 2 interrupt Interrupt request at Vdet2 > VCC and VCC > Vdet2 when digital filter is enabled; interrupt request at Vdet2 > VCC or VCC > Vdet2 when digital filter is disabled Available (Divide-by-n of fOCO-S) x4 n: 1, 2, 4, and 8 R8C/2K Group, R8C/2L Group 6. Voltage Detection Circuit VCA27 VCC - Voltage detection 2 signal Noise filter + Internal reference voltage Vdet2 VCA1 register b3 VCA13 bit VCA26 - Voltage detection 1 signal Noise filter + Vdet1 VW1C register b3 VW1C3 bit VCA25 Voltage detection 0 signal + - Figure 6.1 Vdet0 Block Diagram of Voltage Detection Circuit Voltage monitor 0 reset generation circuit VW0F1 to VW0F0 = 00b = 01b Voltage detection 0 circuit = 10b fOCO-S 1/2 1/2 1/2 = 11b VCA25 VW0C1 VCC Internal reference voltage + Digital filter Voltage detection 0 signal - Voltage detection 0 signal is held "H" when VCA25 bit is set to 0 (disabled) Voltage monitor 0 reset signal VW0C1 VW0C0 VW0C7 VW0C0 to VW0C1, VW0F0 to VW0F1, VW0C6, VW0C7: Bits in VW0C register VCA25: Bit in VCA2 register Figure 6.2 Block Diagram of Voltage Monitor 0 Reset Generation Circuit Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 33 of 450 VW0C6 R8C/2K Group, R8C/2L Group 6. Voltage Detection Circuit Voltage monitor 1 interrupt/reset generation circuit VW1F1 to VW1F0 = 00b = 01b Voltage detection 1 circuit VW1C2 bit is set to 0 (not detected) by writing 0 by a program. When VCA26 bit is set to 0 (voltage detection 1 circuit disabled), VW1C2 bit is set to 0 = 10b fOCO-S 1/2 1/2 1/2 = 11b VCA26 VW1C1 VW1C3 VCC + Noise filter Internal reference voltage (Filter width: 200 ns) Digital filter Voltage detection 1 signal Watchdog timer interrupt signal VW1C2 Voltage detection 1 signal is held "H" when VCA26 bit is set to 0 (disabled) Voltage monitor 1 interrupt signal Non-maskable interrupt signal VW1C1 Oscillation stop detection interrupt signal VW1C7 VW1C0 VW1C6 Voltage monitor 1 reset signal VW1C0 to VW1C3, VW1F0, VW1F1, VW1C6, VW1C7: Bits in VW1C register VCA26: Bit in VCA2 register Figure 6.3 Block Diagram of Voltage Monitor 1 Interrupt/Reset Generation Circuit Voltage monitor 2 interrupt/reset generation circuit VW2F1 to VW2F0 = 00b = 01b Voltage detection 2 circuit = 10b fOCO-S 1/2 1/2 1/2 VW2C2 bit is set to 0 (not detected) by writing 0 by a program. When VCA27 bit is set to 0 (voltage detection 2 circuit disabled), VW2C2 bit is set to 0 = 11b VCA27 VW2C1 VCA13 VCC + Noise filter Internal reference voltage (Filter width: 200 ns) Digital filter Voltage detection 2 signal Watchdog timer interrupt signal VW2C2 Voltage detection 2 signal is held "H" when VCA27 bit is set to 0 (disabled) Voltage monitor 2 interrupt signal Non-maskable interrupt signal VW2C1 Oscillation stop detection interrupt signal Watchdog timer block VW2C3 VW2C7 Watchdog timer underflow signal This bit is set to 0 (not detected) by writing 0 by a program. VW2C0 VW2C6 VW2C0 to VW2C3, VW2F0, VW2F1, VW2C6, VW2C7: Bits in VW2C register VCA13: Bit in VCA1 register VCA27: Bit in VCA2 register Figure 6.4 Block Diagram of Voltage Monitor 2 Interrupt/Reset Generation Circuit Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 34 of 450 Voltage monitor 2 reset signal R8C/2K Group, R8C/2L Group 6. Voltage Detection Circuit Voltage Detection Register 1 b7 b6 b5 b4 b3 b2 b1 b0 0 0 0 0 0 0 0 After Reset(2) 00001000b Function Symbol Address 0031h VCA1 Bit Symbol Bit Name -- Reserved bits (b2-b0) VCA13 -- (b7-b4) Set to 0. Voltage detection 2 signal monitor flag(1) 0 : VCC < Vdet2 1 : VCC Vdet2 or voltage detection 2 circuit disabled Reserved bits Set to 0. RW RW RO RW NOTES: 1. The VCA13 bit is enabled w hen the VCA27 bit in the VCA2 register is set to 1 (voltage detection 2 circuit enabled). The VCA13 bit is set to 1 (VCC Vdet 2) w hen the VCA27 bit in the VCA2 register is set to 0 (voltage detection 2 circuit disabled). 2. The softw are reset, w atchdog timer reset, voltage monitor 1 reset, and voltage monitor 2 reset do not affect this register. Voltage Detection Register 2(1) b7 b6 b5 b4 b3 b2 b1 b0 0 0 0 0 Symbol VCA2 Bit Symbol VCA20 -- (b4-b1) Address 0032h Bit Name Internal pow er low consumption enable bit(6) After Reset(5) The LVD0ON bit in the OFS register is set to 1 and hardw are reset : 00h Pow er-on reset, voltage monitor 0 reset or LVD0ON bit in the OFS register is set to 0, and hardw are reset : 00100000b Function 0 : Disables low consumption 1 : Enables low consumption RW RW Reserved bits Set to 0. VCA25 Voltage detection 0 enable bit(2) 0 : Voltage detection 0 circuit disabled 1 : Voltage detection 0 circuit enabled RW VCA26 Voltage detection 1 enable bit(3) 0 : Voltage detection 1 circuit disabled 1 : Voltage detection 1 circuit enabled RW VCA27 Voltage detection 2 enable bit(4) 0 : Voltage detection 2 circuit disabled 1 : Voltage detection 2 circuit enabled RW RW NOTES: 1. Set the PRC3 bit in the PRCR register to 1 (w rite enable) before w riting to the VCA2 register. 2. To use the voltage monitor 0 reset, set the VCA25 bit to 1. After the VCA25 bit is set to 1 from 0, the voltage detection circuit w aits for td(E-A) to elapse before starting operation. 3. To use the voltage monitor 1 interrupt/reset or the VW1C3 bit in the VW1C register, set the VCA26 bit to 1. After the VCA26 bit is set to 1 from 0, the voltage detection circuit w aits for td(E-A) to elapse before starting operation. 4. To use the voltage monitor 2 interrupt/reset or the VCA13 bit in the VCA1 register, set the VCA27 bit to 1. After the VCA27 bit is set to 1 from 0, the voltage detection circuit w aits for td(E-A) to elapse before starting operation. 5. Softw are reset, w atchdog timer reset, voltage monitor 1 reset, and voltage monitor 2 reset do not affect this register. 6. Use the VCA20 bit only w hen entering to w ait mode. To set the VCA20 bit, follow the procedure show n in Figure 10.9 Procedure for Enabling Reduced Internal Pow er Consum ption Using VCA20 bit. Figure 6.5 Registers VCA1 and VCA2 Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 35 of 450 R8C/2K Group, R8C/2L Group 6. Voltage Detection Circuit Voltage Monitor 0 Circuit Control Register(1) b7 b6 b5 b4 b3 b2 b1 b0 0 Symbol VW0C Bit Symbol VW0C0 VW0C1 VW0C2 -- (b3) 0038h Bit Name Voltage monitor 0 reset enable bit(3) Function 0 : Disable 1 : Enable Set to 0. Reserved bit When read, the content is undefined. Sampling clock select bits b5 b4 0 0 : fOCO-S divided by 0 1 : fOCO-S divided by 1 0 : fOCO-S divided by 1 1 : fOCO-S divided by RW RW Reserved bit VW0F1 VW0C7 The LVD0ON bit in the OFS register is set to 1 and hardw are reset : 0000X000b Pow er-on reset, voltage monitor 0 reset or LVD0ON bit in the OFS register is set to 0, and hardw are reset : 0100X001b Voltage monitor 0 digital filter 0 : Digital filter enabled mode (digital filter circuit enabled) disable mode select bit 1 : Digital filter disabled mode (digital filter circuit disabled) VW0F0 VW0C6 After Reset(2) Address RW RW 1 2 4 8 RO RW RW Voltage monitor 0 circuit mode select bit When the VW0C0 bit is set to 1 (voltage monitor 0 reset enabled), set to 1. RW Voltage monitor 0 reset generation condition select bit(4) When the VW0C1 bit is set to 1 (digital filter disabled mode), set to 1. RW NOTES: 1. Set the PRC3 bit in the PRCR register to 1 (w rite enable) before w riting to the VW0C register. 2. The value remains unchanged after a softw are reset, w atchdog timer reset, voltage monitor 1 reset, and voltage monitor 2 reset. 3. The VW0C0 bit is enabled w hen the VCA25 bit in the VCA2 register is set to 1 (voltage detection 0 circuit enabled). Set the VW0C0 bit to 0 (disable), w hen the VCA25 bit is set to 0 (voltage detection 0 circuit disabled). 4. The VW0C7 bit is enabled w hen the VW0C1 bit set to 1 (digital filter disabled mode). Figure 6.6 VW0C Register Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 36 of 450 R8C/2K Group, R8C/2L Group 6. Voltage Detection Circuit Voltage Monitor 1 Circuit Control Register(1) b7 b6 b5 b4 b3 b2 b1 b0 Symbol VW1C Bit Symbol Address 0036h Bit Name Voltage monitor 1 interrupt/reset enable bit(6) After Reset(8) 00001000b Function RW 0 : Disable 1 : Enable RW Voltage monitor 1 digital filter disable mode select bit(2) 0 : Digital filter enabled mode (digital filter circuit enabled) 1 : Digital filter disabled mode (digital filter circuit disabled) RW VW1C2 Voltage change detection flag(3, 4, 8) 0 : Not detected 1 : Vdet1 crossing detected RW VW1C3 Voltage detection 1 signal monitor 0 : VCC < Vdet1 1 : VCC Vdet1 or voltage detection 1 flag(3, 8) circuit disabled VW1C0 VW1C1 Sampling clock select bits VW1F0 VW1C6 VW1C7 b5 b4 0 0 : fOCO-S divided by 0 1 : fOCO-S divided by 1 0 : fOCO-S divided by 1 1 : fOCO-S divided by VW1F1 RO 1 2 4 8 Voltage monitor 1 circuit mode select bit(5) 0 : Voltage monitor 1 interrupt mode 1 : Voltage monitor 1 reset mode Voltage monitor 1 interrupt/reset generation condition select bit(7, 9) 0 : When VCC reaches Vdet1 or above 1 : When VCC reaches Vdet1 or below RW RW RW RW NOTES: 1. Set the PRC3 bit in the PRCR register to 1 (rew rite enable) before w riting to the VW1C register. 2. To use the voltage monitor 1 interrupt to exit stop mode and to return again, w rite 0 to the VW1C1 bit before w riting 1. 3. Bits VW1C2 and VW1C3 are enabled w hen the VCA26 bit in the VCA2 register is set to 1 (voltage detection 1 circuit enabled). 4. Set this bit to 0 by a program. When 0 is w ritten by a program, it is set to 0 (and remains unchanged even if 1 is w ritten to it). 5. The VW1C6 bit is enabled w hen the VW1C0 bit is set to 1 (voltage monitor 1 interrupt/enabled reset). 6. The VW1C0 bit is enabled w hen the VCA26 bit in the VCA2 register is set to 1 (voltage detection 1 circuit enabled). Set the VW1C0 bit to 0 (disable) w hen the VCA26 bit is set to 0 (voltage detection 1 circuit disabled). 7. The VW1C7 bit is enabled w hen the VW1C1 bit is set to 1 (digital filter disabled mode). 8. Bits VW1C2 and VW1C3 remain unchanged after a softw are reset, w atchdog timer reset, voltage monitor 1 reset, or voltage monitor 2 reset. 9. When the VW1C6 bit is set to 1 (voltage monitor 1 reset mode), set the VW1C7 bit to 1 (w hen VCC reaches Vdet1 or below ). (Do not set to 0.) Figure 6.7 VW1C Register Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 37 of 450 R8C/2K Group, R8C/2L Group 6. Voltage Detection Circuit Voltage Monitor 2 Circuit Control Register(1) b7 b6 b5 b4 b3 b2 b1 b0 Symbol VW2C Bit Symbol VW2C0 VW2C1 VW2C2 VW2C3 Address 0037h Bit Name Voltage monitor 2 interrupt/reset enable bit(6) RW Voltage monitor 2 digital filter disable mode select bit(2) 0 : Digital filter enabled mode (digital filter circuit enabled) 1 : Digital filter disabled mode (digital filter circuit disabled) RW Voltage change detection flag(3, 4, 8) 0 : Not detected 1 : VCC has crossed Vdet2 RW WDT detection flag(4, 8) 0 : Not detected 1 : Detected RW Sampling clock select bits b5 b4 0 0 : fOCO-S divided by 0 1 : fOCO-S divided by 1 0 : fOCO-S divided by 1 1 : fOCO-S divided by VW2F1 VW2C7 RW 0 : Disable 1 : Enable VW2F0 VW2C6 After Reset(8) 00h Function 1 2 4 8 Voltage monitor 2 circuit mode select bit(5) 0 : Voltage monitor 2 interrupt mode 1 : Voltage monitor 2 reset mode Voltage monitor 2 interrupt/reset generation condition select bit(7, 9) 0 : When VCC reaches Vdet2 or above 1 : When VCC reaches Vdet2 or below RW RW RW RW NOTES: 1. Set the PRC3 bit in the PRCR register to 1 (w rite enable) before w riting to the VW2C register. 2. To use the voltage monitor 2 interrupt to exit stop mode and to return again, w rite 0 to the VW2C1 bit before w riting 1. 3. The VW2C2 bit is enabled w hen the VCA27 bit in the VCA2 register is set to 1 (voltage detection 2 circuit enabled). 4. Set this bit to 0 by a program. When 0 is w ritten by a program, it is set to 0 (and remains unchanged even if 1 is w ritten to it). 5. The VW2C6 bit is enabled w hen the VW2C0 bit is set to 1 (voltage monitor 2 interrupt/enables reset). 6. The VW2C0 bit is enabled w hen the VCA27 bit in the VCA2 register is set to 1 (voltage detection 2 circuit enabled). Set the VW2C0 bit to 0 (disable) w hen the VCA27 bit is set to 0 (voltage detection 2 circuit disabled). 7. The VW2C7 bit is enabled w hen the VW2C1 bit is set to 1 (digital filter disabled mode). 8. Bits VW2C2 and VW2C3 remain unchanged after a softw are reset, w atchdog timer reset, voltage monitor 1 reset, or voltage monitor 2 reset. 9. When the VW2C6 bit is set to 1 (voltage monitor 2 reset mode), set the VW2C7 bit to 1 (w hen VCC reaches Vdet2 or below ). (Do not set to 0.) Figure 6.8 VW2C Register Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 38 of 450 R8C/2K Group, R8C/2L Group 6.1 6. Voltage Detection Circuit VCC Input Voltage 6.1.1 Monitoring Vdet0 Vdet0 cannot be monitored. 6.1.2 Monitoring Vdet1 Set the VCA26 bit in the VCA2 register to 1 (voltage detection 1 circuit enabled). After td(E-A) has elapsed (refer to 22. Electrical Characteristics), Vdet1 can be monitored by the VW1C3 bit in the VW1C register. 6.1.3 Monitoring Vdet2 Set the VCA27 bit in the VCA2 register to 1 (voltage detection 2 circuit enabled). After td(E-A) has elapsed (refer to 22. Electrical Characteristics), Vdet2 can be monitored by the VCA13 bit in the VCA1 register. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 39 of 450 R8C/2K Group, R8C/2L Group 6.2 6. Voltage Detection Circuit Voltage Monitor 0 Reset Table 6.2 lists the Procedure for Setting Bits Associated with Voltage Monitor Reset and Figure 6.9 shows an Example of Voltage Monitor 0 Reset Operation. To use the voltage monitor 0 reset to exit stop mode, set the VW0C1 bit in the VW0C register to 1 (digital filter disabled). Table 6.2 Step 1 2 3 4(1) 5(1) 6 7 8 9 Procedure for Setting Bits Associated with Voltage Monitor Reset When Using Digital Filter When Not Using Digital Filter Set the VCA25 bit in the VCA2 register to 1 (voltage detection 0 circuit enabled) Wait for td(E-A) Select the sampling clock of the digital filter Set the VW0C7 bit in the VW0C register to by the VW0F0 to VW0F1 bits in the VW0C 1 register Set the VW0C1 bit in the VW0C register to Set the VW0C1 bit in the VW0C register to 0 (digital filter enabled) 1 (digital filter disabled) Set the VW0C6 bit in the VW0C register to 1 (voltage monitor 0 reset mode) Set the VW0C2 bit in the VW0C register to 0 Set the CM14 bit in the CM1 register to 0 - (low-speed on-chip oscillator on) Wait for 4 cycles of the sampling clock of - (No wait time required) the digital filter Set the VW0C0 bit in the VW0C register to 1 (voltage monitor 0 reset enabled) NOTE: 1. When the VW0C0 bit is set to 0, steps 3, 4, and 5 can be executed simultaneously (with 1 instruction). VCC Vdet0 Sampling clock of digital filter x 4 cycles When the VW0C1 bit is set to 0 (digital filter enabled) 1 x 32 fOCO-S Internal reset signal 1 x 32 fOCO-S When the VW0C1 bit is set to 1 (digital filter disabled) and the VW0C7 bit is set to 1 Internal reset signal VW0C1 and VW0C7: Bits in VW0C register The above applies under the following conditions. * VCA25 bit in VCA2 register = 1 (voltage detection 0 circuit enabled) * VW0C0 bit in VW0C register = 1 (voltage monitor 0 reset enabled) * VW0C6 bit in VW0C register = 1 (voltage monitor 0 reset mode) When the internal reset signal is held "L", the pins, CPU and SFR are reset. The internal reset signal level changes from "L" to "H", and a program is executed beginning with the address indicated by the reset vector. Refer to 4. Special Function Registers (SFRs) for the SFR status after reset. Figure 6.9 Example of Voltage Monitor 0 Reset Operation Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 40 of 450 R8C/2K Group, R8C/2L Group 6.3 6. Voltage Detection Circuit Voltage Monitor 1 Interrupt and Voltage Monitor 1 Reset Table 6.3 lists the Procedure for Setting Bits Associated with Voltage Monitor 1 Interrupt and Reset. Figure 6.10 shows an Example of Voltage Monitor 1 Interrupt and Voltage Monitor 1 Reset Operation. To use the voltage monitor 1 interrupt or voltage monitor 1 reset to exit stop mode, set the VW1C1 bit in the VW1C register to 1 (digital filter disabled). Table 6.3 Step 1 2 3 4(2) 5(2) 6 7 8 9 Procedure for Setting Bits Associated with Voltage Monitor 1 Interrupt and Reset When Using Digital Filter When Not Using Digital Filter Voltage Monitor 1 Voltage Monitor 1 Voltage Monitor 1 Voltage Monitor 1 Interrupt Reset Interrupt Reset Set the VCA26 bit in the VCA2 register to 1 (voltage detection 1 circuit enabled) Wait for td(E-A) Select the sampling clock of the digital filter Select the timing of the interrupt and reset by the VW1F0 to VW1F1 bits in the VW1C request by the VW1C7 bit in the VW1C register register(1) Set the VW1C1 bit in the VW1C register to 0 Set the VW1C1 bit in the VW1C register to 1 (digital filter enabled) (digital filter disabled) Set the VW1C6 bit in Set the VW1C6 bit in Set the VW1C6 bit in Set the VW1C6 bit in the VW1C register to the VW1C register to the VW1C register to the VW1C register to 0 (voltage monitor 1 1 (voltage monitor 1 0 (voltage monitor 1 1 (voltage monitor 1 reset mode) interrupt mode) reset mode) interrupt mode) Set the VW1C2 bit in the VW1C register to 0 (passing of Vdet1 is not detected) Set the CM14 bit in the CM1 register to 0 - (low-speed on-chip oscillator on) Wait for 4 cycles of the sampling clock of the - (No wait time required) digital filter Set the VW1C0 bit in the VW1C register to 1 (voltage monitor 1 interrupt/reset enabled) NOTES: 1. Set the VW1C7 bit to 1 (when VCC reaches Vdet1 or below) for the voltage monitor 1 reset. 2. When the VW1C0 bit is set to 0, steps 3, 4, and 5 can be executed simultaneously (with 1 instruction). Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 41 of 450 R8C/2K Group, R8C/2L Group 6. Voltage Detection Circuit VCC Vdet1 2.2 V(1) 1 VW1C3 bit 0 4 cycles of sampling clock of digital filter 4 cycles of sampling clock of digital filter 1 VW1C2 bit 0 Set to 0 by a program When the VW1C1 bit is set to 0 (digital filter enabled) Set to 0 by interrupt request acknowledgement Voltage monitor 1 interrupt request (VW1C6 = 0) Internal reset signal (VW1C6 = 1) Set to 0 by a program 1 When the VW1C1 bit is set to 1 (digital filter disabled) and the VW1C7 bit is set to 0 (Vdet1 or above) VW1C2 bit 0 Set to 0 by interrupt request acknowledgement Voltage monitor 1 interrupt request (VW1C6 = 0) Set to 0 by a program 1 VW1C2 bit 0 When the VW1C1 bit is set to 1 (digital filter disabled) and the VW1C7 bit is set to 1 (Vdet1 or below) Voltage monitor 1 interrupt request (VW1C6 = 0) Set to 0 by interrupt request acknowledgement Internal reset signal (VW1C6 = 1) VW1C1, VW1C2, VW1C3, VW1C6, VW1C7: Bit in VW1C Register The above applies under the following conditions. * VCA26 bit in VCA2 register = 1 (voltage detection 1 circuit enabled) * VW1C0 bit in VW1C register = 1 (voltage monitor 1 interrupt and voltage monitor 1 reset enabled) NOTE: 1. If voltage monitor 0 reset is not used, set the power supply to VCC 2.2. Figure 6.10 Example of Voltage Monitor 1 Interrupt and Voltage Monitor 1 Reset Operation Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 42 of 450 R8C/2K Group, R8C/2L Group 6.4 6. Voltage Detection Circuit Voltage Monitor 2 Interrupt and Voltage Monitor 2 Reset Table 6.4 lists the Procedure for Setting Bits Associated with Voltage Monitor 2 Interrupt and Reset. Figure 6.11 shows an Example of Voltage Monitor 2 Interrupt and Voltage Monitor 2 Reset Operation. To use the voltage monitor 2 interrupt or voltage monitor 2 reset to exit stop mode, set the VW2C1 bit in the VW2C register to 1 (digital filter disabled). Table 6.4 Step 1 2 3 4 5(2) 6 7 8 9 Procedure for Setting Bits Associated with Voltage Monitor 2 Interrupt and Reset When Using Digital Filter When Not Using Digital Filter Voltage Monitor 2 Voltage Monitor 2 Voltage Monitor 2 Voltage Monitor 2 Interrupt Reset Interrupt Reset Set the VCA27 bit in the VCA2 register to 1 (voltage detection 2 circuit enabled) Wait for td(E-A) Select the sampling clock of the digital filter Select the timing of the interrupt and reset by the VW2F0 to VW2F1 bits in the VW2C request by the VW2C7 bit in the VW2C register register(1) Set the VW2C1 bit in the VW2C register to 0 Set the VW2C1 bit in the VW2C register to 1 (digital filter enabled) (digital filter disabled) Set the VW2C6 bit in Set the VW2C6 bit in Set the VW2C6 bit in Set the VW2C6 bit in the VW2C register to the VW2C register to the VW2C register to the VW2C register to 0 (voltage monitor 2 1 (voltage monitor 2 0 (voltage monitor 2 1 (voltage monitor 2 reset mode) interrupt mode) reset mode) interrupt mode) Set the VW2C2 bit in the VW2C register to 0 (passing of Vdet2 is not detected) Set the CM14 bit in the CM1 register to 0 - (low-speed on-chip oscillator on) Wait for 4 cycles of the sampling clock of the - (No wait time required) digital filter Set the VW2C0 bit in the VW2C register to 1 (voltage monitor 2 interrupt/reset enabled) NOTES: 1. Set the VW2C7 bit to 1 (when VCC reaches Vdet2 or below) for the voltage monitor 2 reset. 2. When the VW2C0 bit is set to 0, steps 3, 4, and 5 can be executed simultaneously (with 1 instruction). Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 43 of 450 R8C/2K Group, R8C/2L Group 6. Voltage Detection Circuit VCC Vdet2 2.2 V(1) 1 VCA13 bit 0 4 cycles of sampling clock of digital filter 4 cycles of sampling clock of digital filter 1 VW2C2 bit 0 Set to 0 by a program When the VW2C1 bit is set to 0 (digital filter enabled) Set to 0 by interrupt request acknowledgement Voltage monitor 2 interrupt request (VW2C6 = 0) Internal reset signal (VW2C6 = 1) Set to 0 by a program 1 When the VW2C1 bit is set to 1 (digital filter disabled) and the VW2C7 bit is set to 0 (Vdet2 or above) VW2C2 bit 0 Set to 0 by interrupt request acknowledgement Voltage monitor 2 interrupt request (VW2C6 = 0) Set to 0 by a program 1 VW2C2 bit 0 When the VW2C1 bit is set to 1 (digital filter disabled) and the VW2C7 bit is set to 1 (Vdet2 or below) Voltage monitor 2 interrupt request (VW2C6 = 0) Set to 0 by interrupt request acknowledgement Internal reset signal (VW2C6 = 1) VCA13: Bit in VCA1 register VW2C1, VW2C2, VW2C6, VW2C7: Bits in VW2C register The above applies under the following conditions. * VCA27 bit in VCA2 register = 1 (voltage detection 2 circuit enabled) * VW2C0 bit in VW2C register = 1 (voltage monitor 2 interrupt and voltage monitor 2 reset enabled) NOTE: 1. When voltage monitor 0 reset is not used, set the power supply to VCC 2.2. Figure 6.11 Example of Voltage Monitor 2 Interrupt and Voltage Monitor 2 Reset Operation Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 44 of 450 R8C/2K Group, R8C/2L Group 7. 7. Programmable I/O Ports Programmable I/O Ports There are 25 programmable Input/Output ports (I/O ports) P0_0 to P0_3, P0_5, P1, P2, P3_3 to P3_5, P4_5. Also, if the XIN clock oscillation circuit is not used, P4_6 and P4_7 can be used as input-only ports. If the A/D converter is not used, P4_2 can be used as an input-only port. Table 7.1 lists an Overview of Programmable I/O Ports. Table 7.1 Overview of Programmable I/O Ports Ports P0_0 to P0_3, P1, P2 I/O I/O Type of Output CMOS3 State I/O Setting Set per bit Set every 4 bits(1) P3_4, P3_5 I/O CMOS3 State Set per bit Set every 2 bits(1) I/O CMOS3 State Set per bit (No output function) None Set every bit(1) None P0_5, P3_3, P4_5 P4_2, P4_6(2), P4_7(2) I Internal Pull-Up Resister NOTES: 1. In input mode, whether an internal pull-up resistor is connected or not can be selected by registers PUR0, and PUR1. 2. When the XIN clock oscillation circuit is not used, these ports can be used as the input-only ports. 7.1 Functions of Programmable I/O Ports The PDi_j (j = 0 to 7) bit in the PDi (i = 0 to 4) register controls I/O of the ports P0_0 to P0_3, P0_5, P1, P2, P3_3 to P3_5, P4_5. The Pi register consists of a port latch to hold output data and a circuit to read pin states. Figures 7.1 to 7.6 show the Configurations of Programmable I/O Ports. Table 7.2 lists the Functions of Programmable I/O Ports. Also, Figure 7.8 shows the PDi (i = 0 to 4) Registers. Figure 7.9 shows the Pi (i = 0 to 4) Registers, Figure 7.10 shows the P2DRR Register, Figure 7.11 shows Registers PINSR1, PINSR2, PINSR3, and PMR, Figure 7.12 shows Registers PUR0, and PUR1. Table 7.2 Functions of Programmable I/O Ports Operation When Value of PDi_j Bit in PDi Register(1) Accessing When PDi_j Bit is Set to 0 (Input Mode) When PDi_j Bit is Set to 1 (Output Mode) Pi Register Reading Read pin input level Read the port latch Writing Write to the port latch Write to the port latch. The value written to the port latch is output from the pin. i = 0 to 4, j = 0 to 7 NOTE: 1. Nothing is assigned to the following bits: PD0_4, PD0_6, PD0_7, PD3_0 to PD3_2, PD3_6, PD3_7, PD4_0 to PD4_4, PD4_6, PD4_7 Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 45 of 450 R8C/2K Group, R8C/2L Group 7.2 7. Programmable I/O Ports Effect on Peripheral Functions Programmable I/O ports function as I/O ports for peripheral functions (Refer to Table 1.7 Pin Name Information by Pin Number). Table 7.3 lists the Setting of PDi_j Bit when Functioning as I/O Ports for Peripheral Functions (i = 0 to 4, j = 0 to 7). Refer to the description of each function for information on how to set peripheral functions. Table 7.3 Setting of PDi_j Bit when Functioning as I/O Ports for Peripheral Functions (i = 0 to 4, j = 0 to 7) I/O of Peripheral Functions PDi_j Bit Settings for Shared Pin Functions Input Set this bit to 0 (input mode). Output This bit can be set to either 0 or 1 (output regardless of the port setting) 7.3 Pins Other than Programmable I/O Ports Figure 7.7 shows the Configuration of I/O Pins. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 46 of 450 R8C/2K Group, R8C/2L Group 7. Programmable I/O Ports P0_0 to P0_3 Pull-up selection Direction register (Note 1) Data bus Port latch (Note 1) Analog input P0_5 Pull-up selection Direction register 1 (Note 1) Output from individual peripheral function Data bus Port latch (Note 1) Input to individual peripheral function Analog input NOTE: 1. symbolizes a parasitic diode. Ensure the input voltage to each port does not exceed VCC. Figure 7.1 Configuration of Programmable I/O Ports (1) Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 47 of 450 R8C/2K Group, R8C/2L Group 7. Programmable I/O Ports P1_0 to P1_3 Pull-up selection Direction register 1 (Note 1) Output from individual peripheral function Data bus Port latch (Note 1) Input to individual peripheral function Analog input P1_4 Pull-up selection Direction register 1 (Note 1) Output from individual peripheral function Data bus Port latch (Note 1) Pull-up selection P1_5 and P1_7 Direction register 1 (Note 1) Output from individual peripheral function Data bus Port latch (Note 1) INT1 input Digital filter Input to individual peripheral function NOTE: 1. symbolizes a parasitic diode. Ensure the input voltage to each port does not exceed VCC. Figure 7.2 Configuration of Programmable I/O Ports (2) Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 48 of 450 R8C/2K Group, R8C/2L Group P1_6 7. Programmable I/O Ports Pull-up selection Direction register 1 (Note 1) Output from individual peripheral function Data bus Port latch (Note 1) Input to individual peripheral function Drive capacity selection P2 Pull-up selection Direction register 1 (Note 1) Output from individual peripheral function Data bus Port latch (Note 1) Input to individual peripheral function Drive capacity selection NOTE: 1. symbolizes a parasitic diode. Ensure the input voltage to each port does not exceed VCC. Figure 7.3 Configuration of Programmable I/O Ports (3) Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 49 of 450 R8C/2K Group, R8C/2L Group 7. Programmable I/O Ports P3_3, P3_4, P3_5 Pull-up selection Direction register 1 (Note 1) Output from individual peripheral function Data bus Port latch (Note 1) Input to individual peripheral function NOTE: 1. symbolizes a parasitic diode. Ensure the input voltage to each port does not exceed VCC. Figure 7.4 Configuration of Programmable I/O Ports (4) Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 50 of 450 R8C/2K Group, R8C/2L Group 7. Programmable I/O Ports (Note 1) P4_2/VREF Data bus (Note 1) P4_5 Pull-up selection Direction register (Note 1) Data bus Port latch (Note 1) INT0 input Digital filter NOTE: 1. symbolizes a parasitic diode. Ensure the input voltage to each port does not exceed VCC. Figure 7.5 Configuration of Programmable I/O Ports (5) Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 51 of 450 R8C/2K Group, R8C/2L Group 7. Programmable I/O Ports (Note 1) P4_6/XIN Data bus (Note 1) Clocked inverter(2) (Note 3) (Note 1) P4_7/XOUT (Note 4) Data bus (Note 1) NOTES: 1. symbolizes a parasitic diode. Ensure the input voltage to each port does not exceed VCC. 2. When CM05 = 1, CM10 = 1, or CM13 = 0, the clocked inverter is cut off. 3. When CM10 = 1 or CM13 = 0, the feedback resistor is disconnected. 4. When CM05 = CM13 = 1 or CM10 = CM13 = 1, this pin is pulled up. Figure 7.6 Configuration of Programmable I/O Ports (6) Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 52 of 450 R8C/2K Group, R8C/2L Group 7. Programmable I/O Ports MODE MODE signal input (Note 1) (Note 1) RESET RESET signal input (Note 1) NOTE: 1. symbolizes a parasitic diode. Ensure the input voltage to each port does not exceed VCC. Figure 7.7 Configuration of I/O Pins Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 53 of 450 R8C/2K Group, R8C/2L Group 7. Programmable I/O Ports Port Pi Direction Register (i = 0 to 4) b7 b6 b5 b4 b3 b2 b1 b0 Symbol PD0(1) PD1 PD2 PD3(2) PD4(3) Bit Symbol PDi_0 PDi_1 PDi_2 PDi_3 PDi_4 PDi_5 PDi_6 PDi_7 Address 00E2h 00E3h 00E6h 00E7h 00EAh Bit Name Port Pi_0 direction bit Port Pi_1 direction bit Port Pi_2 direction bit Port Pi_3 direction bit Port Pi_4 direction bit Port Pi_5 direction bit Port Pi_6 direction bit Port Pi_7 direction bit After Reset 00h 00h 00h 00h 00h Function 0 : Input mode (functions as an input port) 1 : Output mode (functions as an output port) RW RW RW RW RW RW RW RW RW NOTES: 1. Write to the PD0 register w ith the next instruction after that used to set the PRC2 bit in the PRCR register to 1 (w rite enabled). Bits PD0_4, PD0_6, and PD0_7 in the PD0 register are unavailable on this MCU. If it is necessary to set bits PD0_4, PD0_6, and PD0_7 in the PD0 register, set to 0 (input mode). When read, the content is 0. 2. Bits PD3_0 to PD3_2, PD3_6, and PD3_7 in the PD3 register are unavailable on this MCU. If it is necessary to set bits PD3_0 to PD3_2, PD3_6, and PD3_7 in the PD3 register, set to 0 (input mode). When read, the content is 0. 3. Bits PD4_0 to PD4_4, PD4_6, and PD4_7 in the PD4 register are unavailable on this MCU. If it is necessary to set bits PD4_0 to PD4_4, PD4_6, and PD4_7 in the PD4 register, set to 0 (input mode). When read, the content is 0. Figure 7.8 PDi (i = 0 to 4) Registers Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 54 of 450 R8C/2K Group, R8C/2L Group 7. Programmable I/O Ports Port Pi Register (i = 0 to 4) b7 b6 b5 b4 b3 b2 b1 b0 Symbol P0(1) P1 P2 P3(2) P4(3) Bit Symbol Pi_0 Pi_1 Pi_2 Pi_3 Pi_4 Pi_5 Pi_6 Pi_7 Address 00E0h 00E1h 00E4h 00E5h 00E8h Bit Name Port Pi_0 bit Port Pi_1 bit Port Pi_2 bit Port Pi_3 bit Port Pi_4 bit Port Pi_5 bit Port Pi_6 bit Port Pi_7 bit After Reset Undefined Undefined Undefined Undefined Undefined Function The pin level of any I/O port w hich is set to input mode can be read by reading the corresponding bit in this register. The pin level of any I/O port w hich is set to output mode can be controlled by w riting to the corresponding bit in this register. 0 : "L" level 1 : "H" level RW RW RW RW RW RW RW RW RW NOTES: 1. Bits P0_4, P0_6, and P0_7 in the P0 register are unavailable on this MCU. If it is necessary to set bits P0_4, P0_6, and P0_7, set to 0 ("L" level). When read, the content is 0. 2. Bits P3_0 to P3_2, P3_6, and P3_7 in the P3 register are unavailable on this MCU. If it is necessary to set bits P3_0 to P3_2, P3_6, and P3_7, set to 0 ("L" level). When read, the content is 0. 3. Bits P4_0, P4_1, P4_3, and P4_4 in the P4 register are unavailable on this MCU. If it is necessary to set bits P4_0, P4_1, P4_3, and P4_4, set to 0 ("L" level). When read, the content is 0. Figure 7.9 Pi (i = 0 to 4) Registers Port P2 Drive Capacity Control Register b7 b6 b5 b4 b3 b2 b1 b0 Symbol P2DRR Bit Symbol P2DRR0 P2DRR1 P2DRR2 P2DRR3 P2DRR4 P2DRR5 P2DRR6 P2DRR7 Address 00F4h Bit Name P2_0 drive capacity P2_1 drive capacity P2_2 drive capacity P2_3 drive capacity P2_4 drive capacity P2_5 drive capacity P2_6 drive capacity P2_7 drive capacity NOTE: 1. Both "H" and "L" output are set to high drive capacity. Figure 7.10 P2DRR Register Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 55 of 450 After Reset 00h Function Set P2 output transistor drive capacity 0 : Low 1 : High(1) RW RW RW RW RW RW RW RW RW R8C/2K Group, R8C/2L Group 7. Programmable I/O Ports Pin Select Register 1 b7 b0 Symbol PINSR1 Address 00F5h Function After Reset Undefined RW Set to "70h" w hen using UART2. Do not set values other than "70h". When read, its content is undefined. WO Pin Select Register 2 b7 b0 Symbol PINSR2 Address 00F6h Function After Reset Undefined RW Set to "40h" w hen using Timer RB. Do not set values other than "40h". When read, its content is undefined. WO Pin Select Register 3 b7 b0 Symbol PINSR3 Address 00F7h Function After Reset Undefined RW Set to "1Fh" w hen using Timer RC. Do not set values other than "1Fh". When read, its content is undefined. WO Port Mode Register b7 b0 Symbol PMR _____ Address 00F8h Function Set to "04h" w hen using INT3. Do not set values other than "04h". When read, its content is undefined. Figure 7.11 Registers PINSR1, PINSR2, PINSR3, and PMR Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 56 of 450 After Reset 00h RW WO R8C/2K Group, R8C/2L Group 7. Programmable I/O Ports Pull-Up Control Register 0 b7 b6 b5 b4 b3 b2 b1 b0 Symbol PUR0 Bit Symbol PU00 PU01 PU02 PU03 PU04 PU05 PU06 PU07 Address 00FCh Bit Name P0_0 to P0_3 pull-up(1) P0_5 pull-up(1) P1_0 to P1_3 pull-up(1) P1_4 to P1_7 pull-up(1) P2_0 to P2_3 pull-up(1) P2_4 to P2_7 pull-up(1) P3_3 pll-up(1) P3_4 to P3_5 pll-up(1) After Reset 00h Function 0 : Not pulled up 1 : Pulled up RW RW RW RW RW RW RW RW RW NOTE: 1. When this bit is set to 1 (pulled up), the pin w hose direction bit is set to 0 (input mode) is pulled up. Pull-Up Control Register 1 b7 b6 b5 b4 b3 b2 b1 b0 Symbol Address 00FDh PUR1 Bit Symbol Bit Name Nothing is assigned. If necessary, set to 0. -- When read, the content is undefined. (b0) PU11 -- (b7-b2) P4_5 pull-up(1) After Reset XX000000b Function 0 : Not pulled up 1 : Pulled up Nothing is assigned. If necessary, set to 0. When read, the content is undefined. NOTE: 1. When this bit is set to 1 (pulled up), the pin w hose direction bit is set to 0 (input mode) is pulled up. Figure 7.12 Registers PUR0, and PUR1 Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 57 of 450 RW -- RW -- R8C/2K Group, R8C/2L Group 7.4 7. Programmable I/O Ports Port settings Tables 7.4 to 7.36 list the port settings. Table 7.4 Port P0_0/AN7 Register PD0 Bit PD0_0 ADCON0 0 X X X X Setting Value Input port(1) 1 X X X X Output port 0 1 1 1 0 A/D converter input (AN7) CH2 CH1 CH0 Function ADGSEL0 X: 0 or 1 NOTE: 1. Pulled up by setting the PU00 bit in the PUR0 register to 1. Table 7.5 Port P0_1/AN6/TXD2 Register PD0 Bit PD0_1 CH2 CH1 CH0 ADGSEL0 SMD2 SMD1 SMD0 0 X X X X X X X Input port(1) 1 X X X X X X X Output port Setting Value ADCON0 U2MR 0 X X X X X 0 1 1 0 0 Function 1 0 0 1 1 X 1 0 X X TXD2 output(2, 3) A/D converter input (AN6) X: 0 or 1 NOTES: 1. Pulled up by setting the PU00 bit in the PUR0 register to 1. 2. N-channel open drain output by setting the NCH bit in the U2C0 register to 1. 3. To use the UART2, set the PINSR1 register to "70h". Table 7.6 Port P0_2/AN5/RXD2 Register PD0 Bit PD0_2 ADCON0 0 X X X X Input port(1) Setting Value 1 X X X X Output port CH2 CH1 CH0 Function ADGSEL0 0 1 0 1 0 A/D converter input (AN5) 0 X X X X RXD2 output(2) X: 0 or 1 NOTES: 1. Pulled up by setting the PU00 bit in the PUR0 register to 1. 2. To use the UART2, set the PINSR1 register to "70h". Table 7.7 Port P0_3/AN4/CLK2 Register PD0 Bit PD0_3 Setting Value ADCON0 CH2 CH1 CH0 U2MR ADGSEL0 SMD2 SMD1 SMD0 CKDIR X X X X 0 X X X X 1 X X X X Other than 001b Function Input port(1) X Output port 0 X X X X X X X 1 CLK2 (external clock) input(2) X X X X X 0 0 1 0 CLK2 (internal clock) output(2) 0 1 0 0 0 X X X X A/D converter input (AN4) X: 0 or 1 NOTES: 1. Pulled up by setting the PU00 bit in the PUR0 register to 1. 2. To use the UART2, set the PINSR1 register to "70h". Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 58 of 450 R8C/2K Group, R8C/2L Group Table 7.8 7. Programmable I/O Ports Port P0_5/AN2 Register PD0 Bit PD0_5 CH2 CH1 CH0 ADGSEL0 0 X X X X 1 X X X X Output port 0 0 1 0 0 A/D converter input (AN2) Setting Value ADCON0 Function Input port(1) X: 0 or 1 NOTE: 1. Pulled up by setting the PU01 bit in the PUR0 register to 1. Table 7.9 Port P1_0/AN8/KI0 Register PD0 KIEN Bit PD0_3 KI0EN CH2 CH1 ADCON0 CH0 ADGSEL0 0 0 X X X X Input port(1) Setting Value 1 0 X X X X Output port 0 1 X X X X KI0 input 0 0 1 0 0 1 A/D converter input (AN8) Function X: 0 or 1 NOTE: 1. Pulled up by setting the PU02 bit in the PUR0 register to 1. Table 7.10 Register Bit Setting value Port P1_1/AN9/KI1/TRCIOA/TRCTRG PD1 KIEN Timer RC Setting ADCON0 - PD1_1 KI1EN CH2 CH1 CH0 ADGSEL0 Function 0 0 Other than TRCIOA usage conditions X X X X Input port(1) 1 0 Other than TRCIOA usage conditions X X X X Output port 0 0 Other than TRCIOA usage conditions 1 0 1 1 A/D converter input (AN9) 0 1 Other than TRCIOA usage conditions X X X X KI1 input(1) X 0 Refer to Table 7.11 TRCIOA Pin Setting X X X X TRCIOA output(2) 0 0 Refer to Table 7.11 TRCIOA Pin Setting X X X X TRCIOA input(1, 2) X: 0 or 1 NOTES: 1. Pulled up by setting the PU02 bit in the PUR0 register to 1. 2. To use the Timer RC, set the PINSR3 register to "1Fh". Table 7.11 TRCIOA Pin Setting Register TRCOER TRCMR Bit EA PWM2 0 1 Setting value 0 1 1 TRCIOR0 IOA2 IOA1 0 0 1 0 TCEG1 TCEG0 0 1 X X 1 X X X 1 X X X X X Other than above X: 0 or 1 Rev.1.10 Dec 21, 2007 REJ09B0406-0110 TRCCR2 IOA0 Page 59 of 450 X X X X 0 1 1 X Function Timer waveform output (output compare function) Timer mode (input capture function) PWM2 mode TRCTRG input Other than TRCIOA usage conditions R8C/2K Group, R8C/2L Group Table 7.12 Register Bit Setting value 7. Programmable I/O Ports Port P1_2/AN10/KI2/TRCIOB PD1 KIEN Timer RC Setting PD1_2 KI2EN ADCON0 - CH2 CH1 Function CH0 ADGSEL0 0 0 Other than TRCIOB usage conditions X X X X Input port(1) 1 0 Other than TRCIOB usage conditions X X X X Output port 0 0 Other than TRCIOB usage conditions 1 1 0 1 A/D converter input (AN10) 0 1 Other than TRCIOB usage conditions X X X X KI2 input(1) X 0 Refer to Table 7.13 TRCIOB Pin Setting X X X X TRCIOB output(2) 0 0 Refer to Table 7.13 TRCIOB Pin Setting X X X X TRCIOB input(1, 2) X: 0 or 1 NOTES: 1. Pulled up by setting the PU02 bit in the PUR0 register to 1. 2. To use the Timer RC, set the PINSR3 register to "1Fh". Table 7.13 TRCIOB Pin Setting Register TRCOER Bit EB Setting value TRCMR TRCIOR0 PWMB 0 0 X X X X PWM2 mode waveform output 0 1 1 X X X PWM mode waveform output 0 1 0 0 0 1 0 1 X Timer waveform output (output compare function) 1 0 1 X X Timer mode (input capture function) 0 1 IOB2 IOB1 Function PWM2 IOB0 Other than above Other than TRCIOB usage conditions X: 0 or 1 Table 7.14 Port P1_3/AN11/KI3/ TRBO Register PD1 KIEN Timer RB Setting Bit PD1_3 KI3EN - CH2 CH1 CH0 ADGSEL0 0 0 Other than TRBO usage conditions X X X X Input port(1) Setting value ADCON0 Function 1 0 Other than TRBO usage conditions X X X X Output port 0 0 Other than TRBO usage conditions 1 1 1 1 A/D converter input (AN11) 0 1 Other than TRBO usage conditions X X X X KI3 input(1) 0 Refer to Table 7.15 TRBO Pin Setting X X X X TRBO output(2) X X: 0 or 1 NOTES: 1. Pulled up by setting the PU02 bit in the PUR0 register to 1. 2. To use the Timer RB, set the PINSR2 register to "40h". Table 7.15 TRBO Pin Setting Register TRBIOC Bit TOCNT(1) TMOD1 TMOD0 0 0 1 Programmable waveform generation mode 0 1 0 Programmable one-shot generation mode 0 1 1 Programmable wait one-shot generation mode 1 0 1 P1_3 output port Setting value TRBMR Other than above Function Other than TRBO usage conditions NOTE: 1. Set the TOCNT bit in the TRBIOC register to 0 in modes except for programmable waveform generation mode. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 60 of 450 R8C/2K Group, R8C/2L Group Table 7.16 7. Programmable I/O Ports Port P1_4/TXD0 Register PD1 Bit PD1_4 SMD2 U0MR SMD1 SMD0 0 0 0 0 Input port(1) 1 0 0 0 Output port 0 0 1 1 0 0 1 0 1 1 1 0 Setting value X Function TXD0 output(2) X: 0 or 1 NOTES: 1. Pulled up by setting the PU03 bit in the PUR0 register to 1. 2. N-channel open drain output by setting the NCH bit in the U0C0 register to 1. Table 7.17 Port P1_5/RXD0/(TRAIO)/(INT1) Register PD1 Bit PD1_5 TIOSEL TOPCR(2) TMOD2 TMOD1 TMOD0 INT1EN 0 X X X X X 0 1 1 0 0 1 0 1 Setting value 0 X TRAIOC TRAMR INTEN 1 0 0 0 0 0 0 X X X X X 1 0 0 0 0 X 0 X X X X X 1 0 1 0 1 0 0 0 0 1 1 1 0 0 1 1 1 0 1 0 Other than 001b 0 Other than 000b, 001b 0 Other than 000b, 001b 0 0 1 Function Input port(1) Output port RXD0 input(1) TRAIO input(1) INT1 1 TRAIO input/INT1(1) X TRAIO pulse output X: 0 or 1 NOTES: 1. Pulled up by setting the PU03 bit in the PUR0 register to 1. 2. Set the TOPCR bit in the TRAIOC register to 0 in modes except for pulse output mode. Table 7.18 Port P1_6/CLK0 Register PD1 Bit PD1_6 SMD2 SMD1 SMD0 CKDIR 0 X X X X Input port(1) Setting Value U2MR 1 Other than 001b Function X Output port X 0 0 1 0 CLK0 output 0 X X X 1 CLK0 input(1) X: 0 or 1 NOTE: 1. Pulled up by setting the PU03 bit in the PUR0 register to 1. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 61 of 450 R8C/2K Group, R8C/2L Group Table 7.19 7. Programmable I/O Ports Port P1_7/TRAIO/INT1 Register PD1 Bit PD1_7 TRAIOC TRAMR INTEN TIOSEL TOPCR(2) TMOD2 TMOD1 TMOD0 INT1EN 1 X X X X X 0 1 0 0 1 0 0 1 Setting value 0 X 0 0 0 0 0 0 1 X X X X X 0 0 0 0 0 X 0 0 0 0 0 0 0 1 0 1 0 0 1 1 0 0 0 0 Other than 000b, 001b 0 Other than 000b, 001b 0 0 1 Function Input port(1) Output port TRAIO input(1) INT1 1 TRAIO input/INT1(1) X TRAIO pulse output X: 0 or 1 NOTES: 1. Pulled up by setting the PU03 bit in the PUR0 register to 1. 2. Set the TOPCR bit in the TRAIOC register to 0 in modes except for pulse output mode. Table 7.20 Port P2_0/TRDIOA0/TRDCLK Register PD2 TRDOER1 Bit PD2_0 EA0 CMD1 CMD0 0 1 X X X 1 1 X X 0 X 0 0 0 X X X 1 1 0 X 0 0 0 0 0 X 0 0 Setting Value X TRDFCR 0 0 TRDIORA0 STCLK PWM3 0 Function IOA2 IOA1 IOA0 X X X X X X X X X Output port(2) 0 1 1 X X Timer mode (input capture function) 0 0 External clock input (TRDCLK) X X PWM3 mode waveform output(2) 0 1 1 X Timer mode waveform output (output compare function)(2) 0 1 Input port(1) X: 0 or 1 NOTES: 1. Pulled up by setting the PU04 bit in the PUR0 register to 1. 2. Output drive capacity high by setting the P2DRR0 bit in the P2DRR register to 1. Table 7.21 Port P2_1/TRDIOB0 Register PD2 TRDOER1 TRDFCR TRDPMR TRDIORA0 Bit PD2_1 EB0 CMD1 CMD0 PWM3 PWMB0 IOB2 IOB1 IOB0 0 1 X X X X X 1 1 X X X X X X X Output port(2) 0 X 0 0 1 0 1 X X Timer mode (input capture function) X 0 1 0 1 1 X X X X X Complementary PWM mode waveform output X 0 0 1 X X X X X Reset synchronous PWM mode waveform output X 0 0 0 0 X X X X PWM3 mode waveform output(2) X 0 0 0 1 1 X X X PWM mode waveform output(2) X 0 0 0 1 0 0 0 1 0 1 X Timer mode waveform output (output compare function)(2) Setting Value X X Function Input port(1) X: 0 or 1 NOTES: 1. Pulled up by setting the PU04 bit in the PUR0 register to 1. 2. Output drive capacity high by setting the P2DRR1 bit in the P2DRR register to 1. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 62 of 450 R8C/2K Group, R8C/2L Group Table 7.22 7. Programmable I/O Ports Port P2_2/TRDIOC0 Register PD2 TRDOER1 Bit PD2_2 EC0 CMD1 0 1 X X X X X X X 1 1 X X X X X X X Output port(2) 0 X 0 0 1 0 1 X X Timer mode (input capture function) X 0 1 0 1 1 X X X X X Complementary PWM mode waveform output(2) X 0 0 1 X X X X X Reset synchronous PWM mode waveform output(2) X 0 0 0 1 1 X X X PWM mode waveform output(2) X 0 0 0 1 0 0 0 1 0 1 X Timer mode waveform output (output compare function)(2) Setting Value TRDFCR CMD0 PWM3 TRDPMR TRDIORC0 PWMC0 IOC2 IOC1 IOC0 Function Input port(1) X: 0 or 1 NOTES: 1. Pulled up by setting the PU04 bit in the PUR0 register to 1. 2. Output drive capacity high by setting the P2DRR2 bit in the P2DRR register to 1. Table 7.23 Port P2_3/TRDIOD0 Register PD2 TRDOER1 Bit PD2_3 ED0 CMD1 0 1 X X X X X X X 1 1 X X X X X X X Output port(2) 0 X 0 0 1 0 1 X X Timer mode (input capture function) X 0 1 0 1 1 X X X X X Complementary PWM mode waveform output(2) X 0 0 1 X X X X X Reset synchronous PWM mode waveform output(2) X 0 0 0 1 1 X X X PWM mode waveform output(2) 0 0 1 0 1 X Timer mode waveform output (output compare function)(2) Setting Value X 0 TRDFCR 0 CMD0 PWM3 0 TRDPMR TRDIORC0 PWMD0 IOD2 IOD1 IOD0 1 0 Function Input port(1) X: 0 or 1 NOTES: 1. Pulled up by setting the PU04 bit in the PUR0 register to 1. 2. Output drive capacity high by setting the P2DRR3 bit in the P2DRR register to 1. Table 7.24 Port P2_4/TRDIOA1 Register PD2 TRDOER1 Bit PD2_4 EA1 CMD1 0 1 X X X X X X Input port(1) 1 1 X X X X X X Output port(2) 0 X 0 0 1 1 X X Timer mode (input capture function) 1 0 1 1 X X X X Complementary PWM mode waveform output(2) 0 1 X X X X Reset synchronous PWM mode waveform output(2) 0 0 1 0 1 X Timer mode waveform output (output compare function)(2) Setting Value X 0 X 0 X 0 TRDFCR 0 TRDIORA1 CMD0 PWM3 IOA2 0 1 Function IOA1 IOA0 X: 0 or 1 NOTES: 1. Pulled up by setting the PU05 bit in the PUR0 register to 1. 2. Output drive capacity high by setting the P2DRR4 bit in the P2DRR register to 1. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 63 of 450 R8C/2K Group, R8C/2L Group Table 7.25 7. Programmable I/O Ports Port P2_5/TRDIOB1 Register PD2 TRDOER1 Bit PD2_5 EB1 CMD1 0 1 X X X X X X X 1 1 X X X X X X X Output port(2) 0 X 0 0 1 0 1 X X Timer mode (input capture function) X 0 1 0 1 1 X X X X X Complementary PWM mode waveform output(2) X 0 0 1 X X X X X Reset synchronous PWM mode waveform output(2) X 0 0 0 1 1 X X X PWM mode waveform output(2) X 0 0 0 1 0 0 0 1 0 1 X Timer mode waveform output (output compare function)(2) Setting Value TRDFCR CMD0 PWM3 TRDPMR TRDIORA1 PWMB1 IOB2 IOB1 IOB0 Function Input port(1) X: 0 or 1 NOTES: 1. Pulled up by setting the PU05 bit in the PUR0 register to 1. 2. Output drive capacity high by setting the P2DRR5 bit in the P2DRR register to 1. Table 7.26 Port P2_6/TRDIOC1 Register PD2 TRDOER1 Bit PD2_6 EC1 CMD1 0 1 X X X X X X X 1 1 X X X X X X X Output port(2) 0 X 0 0 1 0 1 X X Timer mode (input capture function) X 0 1 0 1 1 X X X X X Complementary PWM mode waveform output(2) X 0 0 1 X X X X X Reset synchronous PWM mode waveform output(2) X 0 0 0 1 1 X X X PWM mode waveform output(2) 0 0 1 0 1 X Timer mode waveform output (output compare function)(2) Setting Value X 0 TRDFCR 0 CMD0 PWM3 0 1 TRDPMR TRDIORC1 PWMC1 IOC2 IOC1 IOC0 0 Function Input port(1) X: 0 or 1 NOTES: 1. Pulled up by setting the PU05 bit in the PUR0 register to 1. 2. Output drive capacity high by setting the P2DRR6 bit in the P2DRR register to 1. Table 7.27 Port P2_7/TRDIOD1 Register PD2 TRDOER1 Bit PD2_7 ED1 CMD1 0 1 X X X X X X X Input port(1) 1 1 X X X X X X X Output port(2) 0 X 0 0 1 0 1 X X Timer mode (input capture function) 1 0 1 1 X X X X X Complementary PWM mode waveform output(2) Setting Value TRDFCR CMD0 PWM3 TRDPMR TRDIORC1 PWMD1 IOD2 IOD1 IOD0 Function X 0 X 0 0 1 X X X X X Reset synchronous PWM mode waveform output(2) X 0 0 0 1 1 X X X PWM mode waveform output(2) 0 0 1 0 1 X Timer mode waveform output (output compare function)(2) X 0 0 0 1 0 X: 0 or 1 NOTES: 1. Pulled up by setting the PU05 bit in the PUR0 register to 1. 2. Output drive capacity high by setting the P2DRR7 bit in the P2DRR register to 1. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 64 of 450 R8C/2K Group, R8C/2L Group Table 7.28 7. Programmable I/O Ports Port P3_3/INT3/ TRCCLK Register PD3 Bit PD3_3 Setting Value TRCCR1 TCK2 INTEN TCK1 TCK0 Function INT3EN 0 Other than 101b 0 Input port(1) 1 Other than 101b 0 Output port 0 Other than 101b 1 INT3 input(1, 2) 0 TRCCLK input(1, 3) 0 1 0 1 NOTES: 1. Pulled up by setting the PU06 bit in the PUR0 register to 1. 2. To use the INT3, set the PMR register to "04h". 3. To use the Timer RC, set the PINSR3 register to "1Fh". Table 7.29 Port P3_4/TRCIOC Register PD3 Timer RC Setting Bit PD3_3 - 0 Other than TRCIOC usage conditions Input port(1) 1 Other than TRCIOC usage conditions Output port X Refer to Table 7.30 TRCIOC Pin Setting TRCIOC output(2) 0 Refer to Table 7.30 TRCIOC Pin Setting TRCIOC input(1, 2) Setting Value Function X: 0 or 1 NOTES: 1. Pulled up by setting the PU07 bit in the PUR0 register to 1. 2. To use the Timer RC, set the PINSR3 register to "1Fh". Table 7.30 TRCIOC Pin Setting Register TRCOER Bit EC PWM2 PWMC IOC2 IOC1 IOC0 0 1 1 X X X PWM mode waveform output 0 0 1 0 1 X Timer waveform output (output compare function) Setting value 0 0 1 TRCMR TRCIOR1 1 0 1 0 1 X X 1 X X Other than above Function Timer mode (input capture function) Other than TRCIOC usage conditions X: 0 or 1 Table 7.31 Port P3_5/TRCIOD Register PD3 Timer RC Setting Bit PD3_5 - 0 Other than TRCIOD usage conditions Setting Value Function Input port(1) 1 Other than TRCIOD usage conditions X Refer to Table 7.32 TRCIOD Pin Setting TRCIOD output(2) 0 Refer to Table 7.32 TRCIOD Pin Setting TRCIOD input(1, 2) X: 0 or 1 NOTES: 1. Pulled up by setting the PU07 bit in the PUR0 register to 1. 2. To use the Timer RC, set the PINSR3 register to "1Fh". Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 65 of 450 Output port R8C/2K Group, R8C/2L Group Table 7.32 7. Programmable I/O Ports TRCIOD Pin Setting Register TRCOER Bit EC PWM2 TRCMR PWMD IOC2 IOC1 IOC0 0 1 1 X X X PWM mode waveform output 0 1 1 X Timer waveform output (output compare function) 0 Setting value 0 1 TRCIOR1 1 0 0 1 0 1 X X X X Other than above Function Timer mode (input capture function) Other than TRCIOD usage conditions X: 0 or 1 Table 7.33 Port P4_2/VREF Register ADCON1 Bit VCUT Setting value 0 Input port 1 Input port/VREF input Table 7.34 Function Port P4_5/INT0 Register PD4 INTEN Bit PD4_5 INT0EN 0 0 Input port(1) Setting Value 1 0 Output port 0 1 INT0 input(1) Function NOTE: 1. Pulled up by setting the PU11 bit in the PUR1 register to 1. Table 7.35 Register Bit Setting Value Port P4_6/XIN CM0 CM1 Circuit specifications CM13 CM11 CM10 1 0 X 0 OFF - 0 1 0 0 ON ON XIN clock oscillation (on-chip feedback resistor enabled) 0 1 1 0 ON OFF XIN clock oscillation (on-chip feedback resistor disabled) 1 1 0 0 OFF ON External clock input 1 1 0 0 OFF ON XIN clock oscillation stop (on-chip feedback resistor enabled) 1 1 1 0 OFF OFF XIN clock oscillation stop (on-chip feedback resistor disabled) 1 1 1 1 OFF OFF XIN clock oscillation stop (stop mode) X: 0 or 1 Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 66 of 450 Feedback resistor Function CM5 Oscillation buffer Input port R8C/2K Group, R8C/2L Group Table 7.36 Register Bit Setting Value 7. Programmable I/O Ports Port P4_7/XOUT CM0 CM1 Circuit specifications CM13 CM11 CM10 1 0 X 0 OFF - 0 1 0 0 ON ON XIN clock oscillation (on-chip feedback resistor enabled) 0 1 1 0 ON OFF XIN clock oscillation (on-chip feedback resistor disabled) 1 1 0 0 OFF ON External clock input 1 1 0 0 OFF ON XIN clock oscillation stop (on-chip feedback resistor enabled) 1 1 1 0 OFF OFF XIN clock oscillation stop (on-chip feedback resistor disabled) 1 1 1 1 OFF OFF XIN clock oscillation stop (stop mode) X: 0 or 1 Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 67 of 450 Feedback resistor Function CM5 Oscillation buffer Input port R8C/2K Group, R8C/2L Group 7.5 7. Programmable I/O Ports Unassigned Pin Handling Table 7.37 lists the Unassigned Pin Handling. Table 7.37 Unassigned Pin Handling Pin Name Ports P0_0 to P0_3, P0_5, P1, P2, P3_3 to P3_5, P4_5 Connection * After setting to input mode, connect each pin to VSS via a resistor (pull-down) or connect each pin to VCC via a resistor (pull-up).(2) * After setting to output mode, leave these pins open.(1,2) Ports P4_2, P4_6, P4_7 VREF Connect to VCC via a pull-up resistor(2) Connect to VCC RESET (3) Connect to VCC via a pull-up resistor(2) NOTES: 1. If these ports are set to output mode and left open, they remain in input mode until they are switched to output mode by a program. The voltage level of these pins may be undefined and the power current may increase while the ports remain in input mode. The content of the direction registers may change due to noise or program runaway caused by noise. In order to enhance program reliability, the program should periodically repeat the setting of the direction registers. 2. Connect these unassigned pins to the MCU using the shortest wire length (2 cm or less) possible. 3. When the power-on reset function is in use. MCU Ports P0_0 to P0_3, (Input mode ) : P0_5, P1, P2, : P3_3 to P3_5, P4_5 (Input mode) (Output mode) Port P4_2, P4_6, P4_7 RESET(1) VREF NOTE: 1. When the power-on reset function is in use. Figure 7.13 Unassigned Pin Handling Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 68 of 450 : : Open R8C/2K Group, R8C/2L Group 8. 8. Processor Mode Processor Mode 8.1 Processor Modes Single-chip mode can be selected as the processor mode. Table 8.1 lists Features of Processor Mode. Figure 8.1 shows the PM0 Register and Figure 8.2 shows the PM1 Register. Table 8.1 Features of Processor Mode Processor Mode Single-chip mode Accessible Areas Pins Assignable as I/O Port Pins SFR, internal RAM, internal ROM All pins are I/O ports or peripheral function I/O pins Processor Mode Register 0(1) b7 b6 b5 b4 b3 b2 b1 b0 0 0 0 Symbol Address PM0 0004h Bit Symbol Bit Name Reserved bits -- (b2-b0) PM03 -- (b7-b4) Softw are reset bit After Reset 00h Function Set to 0. RW RW The MCU is reset w hen this bit is set to 1. When read, the content is 0. Nothing is assigned. If necessary, set to 0. When read, the content is 0. RW -- NOTE: 1. Set the PRC1 bit in the PRCR register to 1 (w rite enable) before rew riting the PM0 register. Figure 8.1 PM0 Register Processor Mode Register 1(1) b7 b6 b5 b4 b3 b2 b1 b0 0 0 0 Symbol Address PM1 0005h Bit Symbol Bit Name -- Reserved bits (b1-b0) PM12 -- (b6-b3) -- (b7) WDT interrupt/reset sw itch bit After Reset 00h Function Set to 0. 0 : Watchdog timer interrupt 1 : Watchdog timer reset(2) Nothing is assigned. If necessary, set to 0. When read, the content is 0. Reserved bit Set to 0. NOTES: 1. Set the PRC1 bit in the PRCR register to 1 (w rite enable) before rew riting the PM1 register. 2. The PM12 bit is set to 1 by a program (and remains unchanged even if 0 is w ritten to it). When the CSPRO bit in the CSPR register is set to 1 (count source protect mode enabled), the PM12 bit is automatically set to 1. Figure 8.2 PM1 Register Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 69 of 450 RW RW RW -- RW R8C/2K Group, R8C/2L Group 9. 9. Bus Bus The bus cycles differ when accessing ROM/RAM, and when accessing SFR. Table 9.1 lists Bus Cycles by Access Space of the R8C/2K Group and Table 9.2 lists Bus Cycles by Access Space of the R8C/2L Group. ROM/RAM and SFR are connected to the CPU by an 8-bit bus. When accessing in word (16-bit) units, these areas are accessed twice in 8-bit units. Table 9.3 lists Access Units and Bus Operations. Table 9.1 Bus Cycles by Access Space of the R8C/2K Group Access Area SFR ROM/RAM Table 9.2 Bus Cycle 2 cycles of CPU clock 1 cycle of CPU clock Bus Cycles by Access Space of the R8C/2L Group Access Area SFR/Data flash Program ROM/RAM Table 9.3 Bus Cycle 2 cycles of CPU clock 1 cycle of CPU clock Access Units and Bus Operations SFR, data flash Area Even address Byte access CPU clock CPU clock Even Address Data Odd address Byte access CPU clock Odd Data Even Data Even+1 Data CPU clock Data Data Odd Data Data CPU clock Data Address Data Address CPU clock Address Even CPU clock Data Odd address Word access Address Data Address Even address Word access ROM (program ROM), RAM Address Data Even Data Even+1 Data CPU clock Odd Odd+1 Data Data Address Data Odd+1 Odd Data Data However, only following SFRs are connected with the 16-bit bus: Timer RC: registers TRC, TRCGRA, TRCGRB, TRCGRC, and TRCGRD Timer RD: registers TRDi (i=0, 1), TRDGRAi, TRDGRBi, TRDGRCi, and TRDGRDi Therefore, when accessing in word (16-bit) unit, 16-bit data is accessed at a time. The bus operation is the same as "Area: SFR, data flash, even address byte access" in Table 9.3 Access Units and Bus Operations, and 16-bit data is accessed at a time. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 70 of 450 R8C/2K Group, R8C/2L Group 10. Clock Generation Circuit 10. Clock Generation Circuit The clock generation circuit has: * XIN clock oscillation circuit * Low-speed on-chip oscillator * High-speed on-chip oscillator Table 10.1 lists the Specifications of Clock Generation Circuit. Figure 10.1 shows a Clock Generation Circuit. Figure 10.2 shows a Peripheral Function Clock. Figures 10.3 to 10.8 show clock associated registers. Table 10.1 Specifications of Clock Generation Circuit Item Applications XIN Clock Oscillation Circuit * CPU clock source * Peripheral function clock source On-Chip Oscillator High-Speed On-Chip Oscillator Low-Speed On-Chip Oscillator * CPU clock source * CPU clock source * Peripheral function clock * Peripheral function clock source source * CPU and peripheral function * CPU and peripheral function clock sources when XIN clock clock sources when XIN clock stops oscillating stops oscillating (3) Approx. 125 kHz Approx. 40 MHz Clock frequency 0 to 20 MHz Connectable oscillator Oscillator connect pins Oscillation stop, restart function Oscillator status after reset Others * Ceramic resonator * Crystal oscillator - - XIN, XOUT(1) -(1) -(1) Usable Usable Usable Stop Stop Oscillate * Externally generated clock can be input(2) * On-chip feedback resistor RfXIN (connected/ not connected, selectable) - - NOTES: 1. These pins can be used as P4_6 or P4_7 when using the on-chip oscillator clock as the CPU clock while the XIN clock oscillation circuit is not used. 2. Set the CM05 bit in the CM0 register to 1 (XIN clock stopped), and the CM13 bit in the CM1 register to 1 (XINXOUT pin) when an external clock is input. 3. The clock frequency is automatically set to up to 20 MHz by a divider when using the high-speed on-chip oscillator as the CPU clock source. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 71 of 450 R8C/2K Group, R8C/2L Group 10. Clock Generation Circuit FRA1 register Frequency adjustable FRA00 High-speed on-chip oscillator fOCO40M FRA2 register Divider fOCO-F FRA01 = 1 Divider (1/128) fOCO fOCO128 On-chip oscillator clock FRA01 = 0 fOCO fOCO-F Low-speed on-chip oscillator CM14 Power-on reset circuit fOCO-S S Q CM10 = 1 (stop mode) Peripheral function clock Voltage detection circuit fOCO-S b f1 R RESET c Power-on reset Software reset Interrupt request Oscillation stop detection S Q WAIT instruction R f2 d f4 e XIN clock OCD2 = 1 f8 g f32 CM13 XIN a Divider h CPU clock OCD2 = 0 XOUT CM13 CM05 System clock CM02 1/2 a g e d c b 1/2 1/2 1/2 1/2 CM06 = 0 CM17 to CM16 = 11b CM06 = 1 CM06 = 0 CM17 to CM16 = 10b h CM06 = 0 CM17 to CM16 = 01b CM02, CM04, CM05, CM06: Bits in CM0 register CM10, CM13, CM14, CM16, CM17: Bits in CM1 register OCD0, OCD1, OCD2: Bits in OCD register FRA00, FRA01: Bits in FRA0 register CM06 = 0 CM17 to CM16 = 00b Detail of divider Oscillation Stop Detection Circuit Forcible discharge when OCD0 = 0 XIN clock Pulse generation circuit for clock edge detection and charge, discharge control circuit Charge, discharge circuit OCD1 Oscillation stop detection interrupt generation circuit detection Watchdog timer interrupt Voltage monitor 1 interrupt Voltage monitor 2 interrupt OCD2 bit switch signal CM14 bit switch signal Figure 10.1 Clock Generation Circuit Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 72 of 450 Oscillation stop detection, Watchdog timer, Voltage monitor 1 interrupt, Voltage monitor 2 interrupt R8C/2K Group, R8C/2L Group 10. Clock Generation Circuit fOCO40M fOCO128 fOCO fOCO-F Watchdog timer fOCO-S INT0 Timer RA Timer RB Timer RC Timer RD A/D converter f1 f2 f4 f8 f32 CPU CPU clock Figure 10.2 Peripheral Function Clock Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 73 of 450 UART0 UART2 R8C/2K Group, R8C/2L Group 10. Clock Generation Circuit System Clock Control Register 0(1) b7 b6 b5 b4 b3 b2 b1 b0 0 0 1 0 0 Symbol Address 0006h CM0 Bit Symbol Bit Name -- Reserved bits (b1-b0) After Reset 01101000b Function Set to 0. RW RW WAIT peripheral function clock stop bit 0 : Peripheral function clock does not stop in w ait mode 1 : Peripheral function clock stops in w ait mode -- (b3) Reserved bit Set to 1. -- (b4) Reserved bit Set to 0. CM05 XIN clock (XIN-XOUT) stop bit(2, 3) 0 : XIN clock oscillates 1 : XIN clock stops (4) RW CM06 System clock division select bit 0(5) 0 : CM16, CM17 enabled 1 : Divide-by-8 mode RW Reserved bit Set to 0. CM02 -- (b7) RW RW RW RW NOTES: 1. Set the PRC0 bit in the PRCR register to 1 (w rite enable) before rew riting the CM0 register. 2. P4_6 and P4_7 can be used as input ports w hen the CM05 bit is set to 1 (XIN clock stops) and the CM13 bit in the CM1 register is set to 0 (P4_6, P4_7). 3. The CM05 bit stops the XIN clock w hen the high-speed on-chip oscillator mode or low -speed on-chip oscillator mode is selected. Do not use this bit to detect w hether the XIN clock is stopped. To stop the XIN clock, set the bits in the follow ing order: (a) Set bits OCD1 to OCD0 in the OCD register to 00b. (b) Set the OCD2 bit to 1 (selects on-chip oscillator clock). 4. During external clock input, only the clock oscillation buffer is turned off and clock input is acknow ledged. 5. When entering stop mode, the CM06 bit is set to 1 (divide-by-8 mode). Figure 10.3 CM0 Register Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 74 of 450 R8C/2K Group, R8C/2L Group 10. Clock Generation Circuit System Clock Control Register 1(1) b7 b6 b5 b4 b3 b2 b1 b0 0 Symbol CM1 Bit Symbol CM10 CM11 -- (b2) Address 0007h Bit Name All clock stop control bit(2, After Reset 00100000b Function 0 : Clock operates 1 : Stops all clocks (stop mode) 3, 4) XIN-XOUT on-chip feedback resistor 0 : On-chip feedback resistor enabled select bit 1 : On-chip feedback resistor disabled Reserved bit Set to 0. (3, 5) CM13 CM14 RW RW RW Port XIN-XOUT sw itch bit 0 : Input ports P4_6, P4_7 1 : XIN-XOUT pin RW Low -speed on-chip oscillation stop bit(4, 6, 7) 0 : Low -speed on-chip oscillator on 1 : Low -speed on-chip oscillator off RW 0 : Low 1 : High RW (8) CM15 RW XIN-XOUT drive capacity select bit (9) System clock division select bits 1 CM16 CM17 b7 b6 0 0 : No division mode 0 1 : Divide-by-2 mode 1 0 : Divide-by-4 mode 1 1 : Divide-by-16 mode RW RW NOTES: 1. Set the PRC0 bit in the PRCR register to 1 (w rite enable) before rew riting the CM1 register. 2. If the CM10 bit is set to 1 (stop mode), the on-chip feedback resistor is disabled. 3. When the CM10 bit is set to 1 (stop mode) and the CM13 bit is set to 1 (XIN-XOUT pin), the XOUT (P4_7) pin goes "H". When the CM13 bit is set to 0 (input ports, P4_6, P4_7), P4_7 (XOUT) enters input mode. 4. In count source protect mode (Refer to 15.2 Count Source Protection Mode Enabled), the value remains unchanged even if bits CM10 and CM14 are set. 5. Once the CM13 bit is set to 1 by a program, it cannot be set to 0. 6. When the OCD2 bit is set to 0 (XIN clock selected), the CM14 bit is set to 1 (low -speed on-chip oscillator stopped). When the OCD2 bit is set to 1 (on-chip oscillator clock selected), the CM14 bit is set to 0 (low -speed on-chip oscillator on). It remains unchanged even if 1 is w ritten to it. 7. When using the voltage monitor 1 interrupt or voltage monitor 2 interrupt (w hen using the digital filter), set the CM14 bit to 0 (low -speed on-chip oscillator on). 8. When entering stop mode, the CM15 bit is set to 1 (drive capacity high). 9. When the CM06 bit is set to 0 (bits CM16, CM17 enabled), bits CM16 to CM17 are enabled. Figure 10.4 CM1 Register Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 75 of 450 R8C/2K Group, R8C/2L Group 10. Clock Generation Circuit Oscillation Stop Detection Register(1) b7 b6 b5 b4 b3 b2 b1 b0 0 0 0 0 Symbol OCD Bit Symbol OCD0 OCD1 OCD2 OCD3 -- (b7-b4) Address After Reset 000Ch 00000100b Bit Name Function Oscillation stop detection enable 0 : Oscillation stop detection function bit(7) disabled(2) 1 : Oscillation stop detection function enabled RW RW Oscillation stop detection interrupt enable bit 0 : Disabled(2) 1 : Enabled RW System clock select bit(4) 0 : Selects XIN clock(7) 1 : Selects on-chip oscillator clock(3) RW Clock monitor bit(5, 6) 0 : XIN clock oscillates 1 : XIN clock stops RO Reserved bits Set to 0. RW NOTES: 1. Set the PRC0 bit in the PRCR register to 1 (w rite enable) before rew riting to the OCD register. 2. Set bits OCD1 to OCD0 to 00b before entering stop mode, high-speed on-chip oscillator mode, or low -speed on-chip oscillator mode (XIN clock stops). 3. The CM14 bit is set to 0 (low -speed on-chip oscillator on) if the OCD2 bit is set to 1 (on-chip oscillator clock selected). 4. The OCD2 bit is automatically set to 1 (on-chip oscillator clock selected) if a XIN clock oscillation stop is detected w hile bits OCD1 to OCD0 are set to 11b. If the OCD3 bit is set to 1 (XIN clock stopped), the OCD2 bit remains unchanged even w hen set to 0 (XIN clock selected). 5. The OCD3 bit is enabled w hen the OCD0 bit is set to 1 (oscillation stop detection function enabled). 6. The OCD3 bit remains 0 (XIN clock oscillates) if bits OCD1 to OCD0 are set to 00b. 7. Refer to Figure 10.14 Procedure for Sw itching Clock Source from Low -Speed On-Chip Oscillator to XIN Clock for the sw itching procedure w hen the XIN clock re-oscillates after detecting an oscillation stop. Figure 10.5 OCD Register Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 76 of 450 R8C/2K Group, R8C/2L Group 10. Clock Generation Circuit High-Speed On-Chip Oscillator Control Register 0(1) b7 b6 b5 b4 b3 b2 b1 b0 0 0 0 0 0 0 Symbol FRA0 Bit Symbol FRA00 FRA01 -- (b7-b2) Address 0023h Bit Name High-speed on-chip oscillator enable bit After Reset 00h Function 0 : High-speed on-chip oscillator off 1 : High-speed on-chip oscillator on RW RW (3) High-speed on-chip oscillator select bit(2) 0 : Selects low -speed on-chip oscillator 1 : Selects high-speed on-chip oscillator Reserved bits Set to 0. RW RW NOTES: 1. Set the PRC0 bit in the PRCR register to 1 (w rite enable) before rew riting the FRA0 register. 2. Change the FRA01 bit under the follow ing conditions. * FRA00 = 1 (high-speed on-chip oscillation) * The CM14 bit in the CM1 register = 0 (low -speed on-chip oscillator on) * Bits FRA22 to FRA20 in the FRA2 register: All divide ratio mode settings are supported w hen VCC = 3.0 V to 5.5 V 000b to 111b Divide ratio of 4 or more w hen VCC = 2.7 V to 5.5 V 010b to 111b (divide by 4 or more) Divide ratio of 8 or more w hen VCC = 2.2 V to 5.5 V 110b to 111b (divide by 8 or more) 3. When setting the FRA01 bit to 0 (low -speed on-chip oscillator selected), do not set the FRA00 bit to 0 (high-speed on-chip oscillator off) at the same time. Set the FRA00 bit to 0 after setting the FRA01 bit to 0. High-Speed On-Chip Oscillator Control Register 1(1) b7 b6 b5 b4 b3 b2 b1 b0 Symbol FRA1 Address 0024h After Reset When Shipping Function The frequency of the high-speed on-chip oscillator is adjusted w ith bits 0 to 7. High-speed on-chip oscillator frequency = 40 MHz (FRA1 register = value w hen shipping) Setting the FRA1 register to a low er value results in a higher frequency. Setting the FRA1 register to a higher value results in a low er frequency.(2) RW RW NOTES: 1. Set the PRC0 bit in the PRCR register to 1 (w rite enable) before rew riting the FRA1 register. 2. When changing the values of the FRA1 register, adjust the FRA1 register so that the frequency of the high-speed on-chip oscillator clock w ill be 40 MHz or less. Figure 10.6 Registers FRA0 and FRA1 Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 77 of 450 R8C/2K Group, R8C/2L Group 10. Clock Generation Circuit High-Speed On-Chip Oscillator Control Register 2(1) b7 b6 b5 b4 b3 b2 b1 b0 0 0 0 0 0 Symbol FRA2 Bit Symbol FRA20 Address 0025h Bit Name High-speed on-chip oscillator frequency sw itching bits b2 b1 b0 0 0 0: Divide-by-2 mode 0 0 1: Divide-by-3 mode 0 1 0: Divide-by-4 mode 0 1 1: Divide-by-5 mode 1 0 0: Divide-by-6 mode 1 0 1: Divide-by-7 mode 1 1 0: Divide-by-8 mode 1 1 1: Divide-by-9 mode FRA21 FRA22 -- (b7-b3) After Reset 00h Function Selects the dividing ratio for the highspeed on-chip oscillator clock. Reserved bits Set to 0. RW RW RW RW RW NOTE: 1. Set the PRC0 bit in the PRCR register to 1 (w rite enable) before rew riting the FRA2 register. High-Speed On-Chip Oscillator Control Register 6 b7 b6 b5 b4 b3 b2 b1 b0 Symbol FRA6 Address 002Bh After Reset When Shipping Function Stores data for frequency correction w hen VCC = 2.2 to 5.5 V. Optimal frequency correction to match the voltage conditions can be achieved by transferring this value to the FRA1 register. RW RO High-Speed On-Chip Oscillator Control Register 7 b7 b6 b5 b4 b3 b2 b1 b0 Symbol FRA7 Address 002Ch After Reset When Shipping Function 36.864 MHz frequency correction data is stored. The oscillation frequency of the high-speed on-chip oscillator can be adjusted to 36.864 MHz by transferring this value to the FRA1 register. Figure 10.7 Registers FRA2, FRA6 and FRA7 Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 78 of 450 RW RO R8C/2K Group, R8C/2L Group 10. Clock Generation Circuit Voltage Detection Register 2(1) b7 b6 b5 b4 b3 b2 b1 b0 0 0 0 0 Symbol VCA2 Bit Symbol VCA20 -- (b4-b1) Address 0032h Bit Name Internal pow er low consumption enable bit(6) After Reset(5) The LVD0ON bit in the OFS register is set to 1 and hardw are reset : 00h Pow er-on reset, voltage monitor 0 reset or LVD0ON bit in the OFS register is set to 0, and hardw are reset : 00100000b Function 0 : Disables low consumption 1 : Enables low consumption RW RW Reserved bits Set to 0. VCA25 Voltage detection 0 enable bit(2) 0 : Voltage detection 0 circuit disabled 1 : Voltage detection 0 circuit enabled RW VCA26 Voltage detection 1 enable bit(3) 0 : Voltage detection 1 circuit disabled 1 : Voltage detection 1 circuit enabled RW VCA27 Voltage detection 2 enable bit(4) 0 : Voltage detection 2 circuit disabled 1 : Voltage detection 2 circuit enabled RW RW NOTES: 1. Set the PRC3 bit in the PRCR register to 1 (w rite enable) before w riting to the VCA2 register. 2. To use the voltage monitor 0 reset, set the VCA25 bit to 1. After the VCA25 bit is set to 1 from 0, the voltage detection circuit w aits for td(E-A) to elapse before starting operation. 3. To use the voltage monitor 1 interrupt/reset or the VW1C3 bit in the VW1C register, set the VCA26 bit to 1. After the VCA26 bit is set to 1 from 0, the voltage detection circuit w aits for td(E-A) to elapse before starting operation. 4. To use the voltage monitor 2 interrupt/reset or the VCA13 bit in the VCA1 register, set the VCA27 bit to 1. After the VCA27 bit is set to 1 from 0, the voltage detection circuit w aits for td(E-A) to elapse before starting operation. 5. Softw are reset, w atchdog timer reset, voltage monitor 1 reset, and voltage monitor 2 reset do not affect this register. 6. Use the VCA20 bit only w hen entering to w ait mode. To set the VCA20 bit, follow the procedure show n in Figure 10.9 Procedure for Enabling Reduced Internal Pow er Consum ption Using VCA20 bit. Figure 10.8 VCA2 Register Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 79 of 450 R8C/2K Group, R8C/2L Group 10. Clock Generation Circuit Exit wait mode by interrupt Handling procedure of internal power low consumption enabled by VCA20 bit (Note 1) In interrupt routine Step (1) Enter low-speed on-chip oscillator mode Step (5) VCA20 0 (internal power low consumption disabled)(2) Step (2) Stop XIN clock and high-speed on-chip oscillator clock Step (6) Start XIN clock or high-speed on-chip oscillator clock Step (3) VCA20 1 (internal power low consumption enabled)(2, 3) Step (7) (Wait until XIN clock oscillation stabilizes) Step (4) Enter wait mode(4) Step (8) Enter high-speed clock mode or high-speed on-chip oscillator mode Step (5) VCA20 0 (internal power low consumption disabled)(2) Step (6) Start XIN clock or high-speed on-chip oscillator clock Step (7) (Wait until XIN clock oscillation stabilizes) Step (8) Enter high-speed clock mode or high-speed on-chip oscillator mode If it is necessary to start the high-speed clock or the high-speed on-chip oscillator in the interrupt routine, execute steps (5) to (7) in the interrupt routine. Interrupt handling Step (1) Enter low-speed on-chip oscillator mode Step (2) Stop XIN clock and high-speed on-chip oscillator clock Step (3) VCA20 1 (internal power low consumption enabled)(2, 3) If the high-speed clock or high-speed on-chip oscillator is started in the interrupt routine, execute steps (1) to (3) at the last of the interrupt routine. Interrupt handling completed NOTES: 1. Execute this routine to handle all interrupts generated in wait mode. However, this does not apply if it is not necessary to start the high-speed clock or high-speed on-chip oscillator during the interrupt routine. 2. Do not set the VCA20 bit to 0 with the instruction immediately after setting the VCA20 bit to 1. Also, do not do the opposite. 3. When the VCA20 bit is set to 1, do not set the CM10 bit to 1 (stop mode). 4. When entering wait mode, follow 10.6.2 Wait Mode. VCA20: Bit in VCA2 register Figure 10.9 Procedure for Enabling Reduced Internal Power Consumption Using VCA20 bit Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 80 of 450 R8C/2K Group, R8C/2L Group 10. Clock Generation Circuit The clocks generated by the clock generation circuits are described below. 10.1 XIN Clock This clock is supplied by the XIN clock oscillation circuit. This clock is used as the clock source for the CPU and peripheral function clocks. The XIN clock oscillation circuit is configured by connecting a resonator between the XIN and XOUT pins. The XIN clock oscillation circuit includes an on-chip feedback resistor, which is disconnected from the oscillation circuit in stop mode in order to reduce the amount of power consumed by the chip. The XIN clock oscillation circuit may also be configured by feeding an externally generated clock to the XIN pin. Figure 10.10 shows Examples of XIN Clock Connection Circuit. In reset and after reset, the XIN clock stops. The XIN clock starts oscillating when the CM05 bit in the CM0 register is set to 0 (XIN clock oscillates) after setting the CM13 bit in the CM1 register to 1 (XIN- XOUT pin). To use the XIN clock for the CPU clock source, set the OCD2 bit in the OCD register to 0 (select XIN clock) after the XIN clock is oscillating stably. The power consumption can be reduced by setting the CM05 bit in the CM0 register to 1 (XIN clock stops) if the OCD2 bit is set to 1 (select on-chip oscillator clock). When an external clock is input to the XIN pin are input, the XIN clock does not stop if the CM05 bit is set to 1. If necessary, use an external circuit to stop the clock. This MCU has an on-chip feedback resistor and on-chip resistor disable/enable switching is possible by the CM11 bit in the CM1 register. In stop mode, all clocks including the XIN clock stop. Refer to 10.4 Power Control for details. MCU (on-chip feedback resistor) MCU (on-chip feedback resistor) XIN XIN XOUT XOUT Open Rf(1) Rd(1) Externally derived clock CIN COUT VCC VSS Ceramic resonator external circuit External clock input circuit NOTE: 1. Insert a damping resistor if required. The resistance will vary depending on the oscillator and the oscillation drive capacity setting. Use the value recommended by the manufacturer of the oscillator. Use high drive when oscillation starts and, if it is necessary to switch the oscillation drive capacity, do so after oscillation stabilizes. When the oscillation drive capacity is set to low, check that oscillation is stable. Also, if the oscillator manufacturer's data sheet specifies that a feedback resistor be added to the chip externally, insert a feedback resistor between XIN and XOUT following the instructions. To use this MCU with supply voltage below VCC = 2.7 V, it is recommended to set the CM11 bit in the CM1 register to 1 (on-chip feedback resistor disabled), the CM15 bit to 1 (high drive capacity), and connect the feedback resistor to the chip externally. Figure 10.10 Examples of XIN Clock Connection Circuit Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 81 of 450 R8C/2K Group, R8C/2L Group 10.2 10. Clock Generation Circuit On-Chip Oscillator Clocks These clocks are supplied by the on-chip oscillators (high-speed on-chip oscillator and a low-speed on-chip oscillator). The on-chip oscillator clock is selected by the FRA01 bit in the FRA0 register. 10.2.1 Low-Speed On-Chip Oscillator Clock The clock generated by the low-speed on-chip oscillator is used as the clock source for the CPU clock, peripheral function clock, fOCO, and fOCO-S. After reset, the on-chip oscillator clock generated by the low-speed on-chip oscillator divided by 8 is selected as the CPU clock. If the XIN clock stops oscillating when bits OCD1 to OCD0 in the OCD register are set to 11b, the low-speed on-chip oscillator automatically starts operating, supplying the necessary clock for the MCU. The frequency of the low-speed on-chip oscillator varies depending on the supply voltage and the operating ambient temperature. Application products must be designed with sufficient margin to allow for frequency changes. 10.2.2 High-Speed On-Chip Oscillator Clock The clock generated by the high-speed on-chip oscillator is used as the clock source for the CPU clock, peripheral function clock, fOCO, fOCO-F, and fOCO40M. To use the high-speed on-chip oscillator clock as the clock source for the CPU clock, peripheral clock, fOCO, and fOCO-F, set bits FRA20 to FRA22 in the FRA2 register as follows: * All divide ratio mode settings are supported when VCC = 3.0 V to 5.5 V 000b to 111b * Divide ratio of 4 or more when VCC = 2.7 V to 5.5 V 010b to 111b (divide by 4 or more) * Divide ratio of 8 or more when VCC = 2.2 V to 5.5 V 110b to 111b (divide by 8 or more) After reset, the on-chip oscillator clock generated by the high-speed on-chip oscillator stops. Oscillation is started by setting the FRA00 bit in the FRA0 register to 1 (high-speed on-chip oscillator on). The frequency can be adjusted by registers FRA1 and FRA2. Furthermore, frequency correction data corresponding to the supply voltage ranges VCC = 2.2 V to 5.5 V is stored in FRA6 register. To use separate correction values to match this voltage ranges, transfer them from the FRA6 register to the FRA1 register. The frequency correction data of 36.864 MHz is stored in the FRA7 register. To set the frequency of the highspeed on-chip oscillator to 36.864 MHz, transfer the correction value in the FRA7 register to the FRA1 register before use. This enables the setting errors of bit rates such as 9600 bps and 38400 bps to be 0% when the serial interface is used in UART mode (refer to Table 17.7 Bit Rate Setting Example in UART Mode). Since there are differences in the amount of frequency adjustment among the bits in the FRA1 register, make adjustments by changing the settings of individual bits. Adjust the FRA1 register so that the frequency of the high-speed on-chip oscillator clock will be 40 MHz or less. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 82 of 450 R8C/2K Group, R8C/2L Group 10.3 10. Clock Generation Circuit CPU Clock and Peripheral Function Clock There are a CPU clock to operate the CPU and a peripheral function clock to operate the peripheral functions. Refer to Figure 10.1 Clock Generation Circuit. 10.3.1 System Clock The system clock is the clock source for the CPU and peripheral function clocks. Either the XIN clock or the on-chip oscillator clock can be selected. 10.3.2 CPU Clock The CPU clock is an operating clock for the CPU and watchdog timer. The system clock can be divided by 1 (no division), 2, 4, 8, or 16 to produce the CPU clock. Use the CM06 bit in the CM0 register and bits CM16 to CM17 in the CM1 register to select the value of the division. After reset, the low-speed on-chip oscillator clock divided by 8 provides the CPU clock. When entering stop mode from high-speed clock mode, the CM06 bit is set to 1 (divide-by-8 mode). 10.3.3 Peripheral Function Clock (f1, f2, f4, f8, and f32) The peripheral function clock is the operating clock for the peripheral functions. The clock fi (i = 1, 2, 4, 8, and 32) is generated by the system clock divided by i. The clock fi is used for timers RA, RB, RC, and RD, the serial interface and the A/D converter. When the WAIT instruction is executed after setting the CM02 bit in the CM0 register to 1 (peripheral function clock stops in wait mode), the clock fi stop. 10.3.4 fOCO fOCO is an operating clock for the peripheral functions. fOCO runs at the same frequency as the on-chip oscillator clock and can be used as the source for timer RA. When the WAIT instruction is executed, the clocks fOCO does not stop. 10.3.5 fOCO40M fOCO40M is used as the count source for timer RC and timer RD. fOCO40M is generated by the high-speed on-chip oscillator and supplied by setting the FRA00 bit to 1. When the WAIT instruction is executed, the clock fOCO40M does not stop. fOCO40M can be used with supply voltage VCC = 3.0 to 5.5 V. 10.3.6 fOCO-F fOCO-F is used as the count source for the A/D converter. fOCO-F is generated by the high-speed on-chip oscillator and supplied by setting the FRA00 bit to 1. When the WAIT instruction is executed, the clock fOCO-F does not stop. 10.3.7 fOCO-S fOCO-S is an operating clock for the watchdog timer and voltage detection circuit. fOCO-S is supplied by setting the CM14 bit to 0 (low-speed on-chip oscillator on) and uses the clock generated by the low-speed onchip oscillator. When the WAIT instruction is executed or in count source protect mode of the watchdog timer, fOCO-S does not stop. 10.3.8 fOCO128 fOCO128 is generated by fOCO divided by 128. The clock fOCO128 is used for capture signal of timer RC's TRCGRA register and timer RD (channel 0). Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 83 of 450 R8C/2K Group, R8C/2L Group 10.4 10. Clock Generation Circuit Power Control There are three power control modes. All modes other than wait mode and stop mode are referred to as standard operating mode. 10.4.1 Standard Operating Mode Standard operating mode is further separated into four modes. In standard operating mode, the CPU clock and the peripheral function clock are supplied to operate the CPU and the peripheral function clocks. Power consumption control is enabled by controlling the CPU clock frequency. The higher the CPU clock frequency, the more processing power increases. The lower the CPU clock frequency, the more power consumption decreases. When unnecessary oscillator circuits stop, power consumption is further reduced. Before the clock sources for the CPU clock can be switched over, the new clock source needs to be oscillating and stable. If the new clock source is the XIN clock, allow sufficient wait time in a program until oscillation is stabilized before exiting. Table 10.2 Settings and Modes of Clock Associated Bits Modes High-speed clock mode High-speed on-chip oscillator mode Low-speed on-chip oscillator mode No division Divide-by-2 Divide-by-4 Divide-by-8 Divide-by-16 No division Divide-by-2 Divide-by-4 Divide-by-8 Divide-by-16 No division Divide-by-2 Divide-by-4 Divide-by-8 Divide-by-16 OCD Register OCD2 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 -: can be 0 or 1, no change in outcome Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 84 of 450 CM1 Register CM17, CM16 CM14 00b - 01b - 10b - - - 11b - 00b - 01b - 10b - - - 11b - 00b 0 01b 0 10b 0 - 0 11b 0 CM13 1 1 1 1 1 - - - - - - - - - - CM0 Register CM06 CM05 0 0 0 0 0 0 1 0 0 0 0 - 0 - 0 - 1 - 0 - 0 - 0 - 0 - 1 - 0 - FRA0 Register FRA01 FRA00 - - - - - - - - - - 1 1 1 1 1 1 1 1 1 1 0 - 0 - 0 - 0 - 0 - R8C/2K Group, R8C/2L Group 10.4.1.1 10. Clock Generation Circuit High-Speed Clock Mode The XIN clock divided by 1 (no division), 2, 4, 8, or 16 provides the CPU clock. Set the CM06 bit to 1 (divideby-8 mode) when transiting to high-speed on-chip oscillator mode, low-speed on-chip oscillator mode. If the CM14 bit is set to 0 (low-speed on-chip oscillator on) or the FRA00 bit in the FRA0 register is set to 1 (highspeed on-chip oscillator on), fOCO can be used as timer RA. When the FRA00 bit is set to 1, fOCO40M can be used as timer RC and timer RD. When the CM14 bit is set to 0 (low-speed on-chip oscillator on), fOCO-S can be used as the watchdog timer and voltage detection circuit. 10.4.1.2 High-Speed On-Chip Oscillator Mode The high-speed on-chip oscillator is used as the on-chip oscillator clock when the FRA00 bit in the FRA0 register is set to 1 (high-speed on-chip oscillator on) and the FRA01 bit in the FRA0 register is set to 1. The onchip oscillator divided by 1 (no division), 2, 4, 8, or 16 provides the CPU clock. Set the CM06 bit to 1 (divideby-8 mode) when transiting to high-speed clock mode. If the FRA00 bit is set to 1, fOCO40M can be used as timer RC and timer RD. When the CM14 bit is set to 0 (low-speed on-chip oscillator on), fOCO-S can be used as the watchdog timer and voltage detection circuit. 10.4.1.3 Low-Speed On-Chip Oscillator Mode If the CM14 bit in the CM1 register is set to 0 (low-speed on-chip oscillator on) or the FRA01bit in the FRA0 register is set to 0, the low-speed on-chip oscillator provides the on-chip oscillator clock. The on-chip oscillator clock divided by 1 (no division), 2, 4, 8 or 16 provides the CPU clock. The on-chip oscillator clock is also the clock source for the peripheral function clocks. Set the CM06 bit to 1 (divide-by-8 mode) when transiting to high-speed clock mode. When the FRA00 bit is set to 1, fOCO40M can be used as timer RC and timer RD. When the CM14 bit is set to 0 (low-speed on-chip oscillator on), fOCO-S can be used as the watchdog timer and voltage detection circuit. In this mode, stopping the XIN clock and high-speed on-chip oscillator, and setting the FMR47 bit in the FMR4 register to 1 (flash memory low consumption current read mode enabled) enables low consumption operation. To enter wait mode from low-speed on-chip oscillator mode, setting the VCA20 bit in the VCA2 register to 1 (internal power low consumption enabled) enables lower consumption current in wait mode. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 85 of 450 R8C/2K Group, R8C/2L Group 10.4.2 10. Clock Generation Circuit Wait Mode Since the CPU clock stops in wait mode, the CPU, which operates using the CPU clock, and the watchdog timer, when count source protection mode is disabled, stop. The XIN clock and on-chip oscillator clock do not stop and the peripheral functions using these clocks continue operating. 10.4.2.1 Peripheral Function Clock Stop Function If the CM02 bit is set to 1 (peripheral function clock stops in wait mode), the f1, f2, f4, f8, and f32 clocks stop in wait mode. This reduces power consumption. 10.4.2.2 Entering Wait Mode The MCU enters wait mode when the WAIT instruction is executed. When the OCD2 bit in the OCD register is set to 1 (on-chip oscillator selected as system clock), set the OCD1 bit in the OCD register to 0 (oscillation stop detection interrupt disabled) before executing the WAIT instruction. If the MCU enters wait mode while the OCD1 bit is set to 1 (oscillation stop detection interrupt enabled), current consumption is not reduced because the CPU clock does not stop. 10.4.2.3 Pin Status in Wait Mode The I/O port is the status before wait mode was entered is maintained. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 86 of 450 R8C/2K Group, R8C/2L Group 10.4.2.4 10. Clock Generation Circuit Exiting Wait Mode The MCU exits wait mode by a reset or a peripheral function interrupt. The peripheral function interrupts are affected by the CM02 bit. When the CM02 bit is set to 0 (peripheral function clock does not stop in wait mode), all peripheral function interrupts can be used to exit wait mode. When the CM02 bit is set to 1 (peripheral function clock stops in wait mode), the peripheral functions using the peripheral function clock stop operating and the peripheral functions operated by external signals or on-chip oscillator clock can be used to exit wait mode. Table 10.3 lists Interrupts to Exit Wait Mode and Usage Conditions. Table 10.3 Interrupts to Exit Wait Mode and Usage Conditions Interrupt Serial interface interrupt Key input interrupt A/D conversion interrupt Timer RA interrupt CM02 = 0 Usable when operating with internal or external clock Usable Usable in one-shot mode Usable in all modes Timer RB interrupt Timer RC interrupt Timer RD interrupt Usable in all modes Usable in all modes Usable in all modes INT interrupt Usable Voltage monitor 1 interrupt Voltage monitor 2 interrupt Oscillation stop detection interrupt Usable Usable Usable Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 87 of 450 CM02 = 1 Usable when operating with external clock Usable (Do not use) Can be used if there is no filter in event counter mode. Usable by selecting fOCO or fC32 as count source. (Do not use) (Do not use) Usable by selecting fOCO40M as count source. Usable (INT0, INT1, INT3 can be used if there is no filter.) Usable Usable (Do not use) R8C/2K Group, R8C/2L Group 10. Clock Generation Circuit Figure 10.11 shows the Time from Wait Mode to Interrupt Routine Execution. When using a peripheral function interrupt to exit wait mode, set up the following before executing the WAIT instruction. (1) Set the interrupt priority level in bits ILVL2 to ILVL0 in the interrupt control registers of the peripheral function interrupts to be used for exiting wait mode. Set bits ILVL2 to ILVL0 of the peripheral function interrupts that are not to be used for exiting wait mode to 000b (interrupt disabled). (2) Set the I flag to 1. (3) Operate the peripheral function to be used for exiting wait mode. When exiting by a peripheral function interrupt, the time (number of cycles) between interrupt request generation and interrupt routine execution is determined by the settings of the FMSTP bit in the FMR0 register, as described in Figure 10.11. The CPU clock, when exiting wait mode by a peripheral function interrupt, is the same clock as the CPU clock when the WAIT instruction is executed. FMR0 Register FMSTP Bit Time until Flash Memory is Activated (T1) Time until CPU Clock is Supplied (T2) 0 (flash memory operates) Period of XIN clock x 12 cycles + 30 s (max.) Period of CPU clock x 6 cycles 1 (flash memory stops) Period of XIN clock x 12 cycles Same as above Wait mode Time for Interrupt Sequence (T3) Period of CPU clock Following total time is x 20 cycles the time from wait mode until an interrupt Same as above routine is executed. T1 T2 T3 Flash memory activation sequence CPU clock restart sequence Interrupt sequence Interrupt request generated Figure 10.11 Time from Wait Mode to Interrupt Routine Execution Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Remarks Page 88 of 450 R8C/2K Group, R8C/2L Group 10.4.3 10. Clock Generation Circuit Stop Mode Since the oscillator circuits stop in stop mode, the CPU clock and peripheral function clock stop and the CPU and peripheral functions that use these clocks stop operating. The least power required to operate the MCU is in stop mode. If the voltage applied to the VCC pin is VRAM or more, the contents of internal RAM is maintained. The peripheral functions clocked by external signals continue operating. Table 10.4 lists Interrupts to Exit Stop Mode and Usage Conditions. Table 10.4 Interrupts to Exit Stop Mode and Usage Conditions Interrupt Key input interrupt Usage Conditions - INT0, INT1, INT3 interrupt Timer RA interrupt Serial interface interrupt Voltage monitor 1 interrupt Voltage monitor 2 interrupt 10.4.3.1 Can be used if there is no filter When there is no filter and external pulse is counted in event counter mode When external clock is selected Usable in digital filter disabled mode (VW1C1 bit in VW1C register is set to 1) Usable in digital filter disabled mode (VW2C1 bit in VW2C register is set to 1) Entering Stop Mode The MCU enters stop mode when the CM10 bit in the CM1 register is set to 1 (all clocks stop). At the same time, the CM06 bit in the CM0 register is set to 1 (divide-by-8 mode) and the CM15 bit in the CM1 register is set to 1 (XIN clock oscillator circuit drive capacity high). When using stop mode, set bits OCD1 to OCD0 to 00b before entering stop mode. 10.4.3.2 Pin Status in Stop Mode The status before wait mode was entered is maintained. However, when the CM13 bit in the CM1 register is set to 1 (XIN-XOUT pins), the XOUT(P4_7) pin is held "H". When the CM13 bit is set to 0 (input ports P4_6 and P4_7), the P4_7(XOUT pin) is held in input status. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 89 of 450 R8C/2K Group, R8C/2L Group 10.4.3.3 10. Clock Generation Circuit Exiting Stop Mode The MCU exits stop mode by a reset or peripheral function interrupt. Figure 10.12 shows the Time from Stop Mode to Interrupt Routine Execution. When using a peripheral function interrupt to exit stop mode, set up the following before setting the CM10 bit to 1. (1) Set the interrupt priority level in bits ILVL2 to ILVL0 of the peripheral function interrupts to be used for exiting stop mode. Set bits ILVL2 to ILVL0 of the peripheral function interrupts that are not to be used for exiting stop mode to 000b (interrupt disabled). (2) Set the I flag to 1. (3) Operates the peripheral function to be used for exiting stop mode. When exiting by a peripheral function interrupt, the interrupt sequence is executed when an interrupt request is generated and the CPU clock supply is started. If the clock used immediately before stop mode is a system clock and stop mode is exited by a peripheral function interrupt, the CPU clock becomes the previous system clock divided by 8. FMR0 Register Time until Flash Memory is Activated (T2) Time until CPU Clock is Supplied (T3) 0 (flash memory operates) Period of XIN clock x 12 cycles + 30 s (max.) Period of CPU clock x 6 cycles 1 (flash memory stops) Period of XIN clock x 12 cycles Same as above FMSTP Bit Stop mode Time for Interrupt Sequence (T4) Period of CPU clock Following total time of T0 to T4 x 20 cycles is the time from stop mode until an interrupt Same as above handling is executed. T0 T1 T2 T3 T4 Internal power stability time Oscillation time of CPU clock source used immediately before stop mode Flash memory activation sequence CPU clock restart sequence Interrupt sequence 150 s Interrupt (max.) request generated Figure 10.12 Time from Stop Mode to Interrupt Routine Execution Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 90 of 450 Remarks R8C/2K Group, R8C/2L Group 10. Clock Generation Circuit Figure 10.13 shows the State Transitions in Power Control Mode. State Transitions in Power Control Mode Reset Standard operating mode Low-speed on-chip oscillator mode CM14 = 0 OCD2 = 1 FRA01 = 0 CM14 = 0 OCD2 = 1 FRA01 = 0 CM05 = 0 CM13 = 1 OCD2 = 0 High-speed clock mode CM14 = 0 FRA01 = 0 CM05 = 0 CM13 = 1 OCD2 = 0 FRA00 = 1 FRA01 = 1 OCD2 = 1 FRA00 = 1 FRA01 = 1 CM05 = 0 CM13 = 1 OCD2 = 0 High-speed on-chip oscillator mode OCD2 = 1 FRA00 = 1 FRA01 = 1 Interrupt WAIT instruction Wait mode Stop mode CPU operation stops All oscillators stop CM05: Bit in CM0 register CM13, CM14: Bits in CM1 register OCD2: Bit in OCD register FRA00, FRA01: Bits in FRA0 register Figure 10.13 CM10 = 1 Interrupt State Transitions in Power Control Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 91 of 450 R8C/2K Group, R8C/2L Group 10.5 10. Clock Generation Circuit Oscillation Stop Detection Function The oscillation stop detection function detects the stop of the XIN clock oscillating circuit. The oscillation stop detection function can be enabled and disabled by the OCD0 bit in the OCD register. Table 10.5 lists the Specifications of Oscillation Stop Detection Function. When the XIN clock is the CPU clock source and bits OCD1 to OCD0 are set to 11b, the system is placed in the following state if the XIN clock stops. * OCD2 bit in OCD register = 1 (on-chip oscillator clock selected) * OCD3 bit in OCD register = 1 (XIN clock stops) * CM14 bit in CM1 register = 0 (low-speed on-chip oscillator oscillates) * Oscillation stop detection interrupt request is generated. Table 10.5 Specifications of Oscillation Stop Detection Function Item Oscillation stop detection clock and frequency bandwidth Enabled condition for oscillation stop detection function Operation at oscillation stop detection 10.5.1 Specification f(XIN) 2 MHz Set bits OCD1 to OCD0 to 11b Oscillation stop detection interrupt is generated How to Use Oscillation Stop Detection Function * The oscillation stop detection interrupt shares a vector with the voltage monitor 1 interrupt, the voltage monitor 2 interrupt, and the watchdog timer interrupt. When using the oscillation stop detection interrupt and watchdog timer interrupt, the interrupt source needs to be determined. Table 10.6 lists the Determining Interrupt Source for Oscillation Stop Detection, Watchdog Timer, Voltage Monitor 1, and Voltage Monitor 2 Interrupts. Figure 10.15 shows the Example of Determining Interrupt Source for Oscillation Stop Detection, Watchdog Timer, Voltage Monitor 1, or Voltage Monitor 2 Interrupt. * When the XIN clock restarts after oscillation stop, switch the XIN clock to the clock source of the CPU clock and peripheral functions by a program. Figure 10.14 shows the Procedure for Switching Clock Source from Low-Speed On-Chip Oscillator to XIN Clock. * To enter wait mode while using the oscillation stop detection function, set the CM02 bit to 0 (peripheral function clock does not stop in wait mode). * Since the oscillation stop detection function is a function for cases where the XIN clock is stopped by an external cause, set bits OCD1 to OCD0 to 00b when the XIN clock stops or is started by a program, (stop mode is selected or the CM05 bit is changed). * This function cannot be used when the XIN clock frequency is 2 MHz or below. In this case, set bits OCD1 to OCD0 to 00b. * To use the low-speed on-chip oscillator clock for the CPU clock and clock sources of peripheral functions after detecting the oscillation stop, set the FRA01 bit in the FRA0 register to 0 (low-speed on-chip oscillator selected) and bits OCD1 to OCD0 to 11b. To use the high-speed on-chip oscillator clock for the CPU clock and clock sources of peripheral functions after detecting the oscillation stop, set the FRA00 bit to 1 (high-speed on-chip oscillator on) and the FRA01 bit to 1 (high-speed on-chip oscillator selected) and then set bits OCD1 to OCD0 to 11b. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 92 of 450 R8C/2K Group, R8C/2L Group Table 10.6 10. Clock Generation Circuit Determining Interrupt Source for Oscillation Stop Detection, Watchdog Timer, Voltage Monitor 1, and Voltage Monitor 2 Interrupts Generated Interrupt Source Bit Showing Interrupt Cause Oscillation stop detection (a) OCD3 bit in OCD register = 1 ((a) or (b)) (b) OCD1 to OCD0 bits in OCD register = 11b and OCD2 bit = 1 Watchdog timer VW2C3 bit in VW2C register = 1 Voltage monitor 1 VW1C2 bit in VW1C register = 1 Voltage monitor 2 VW2C2 bit in VW2C register = 1 Switch to XIN clock NO Multiple confirmations that OCD3 bit is set to 0 (XIN clock oscillates) ? YES Set OCD1 to OCD0 bits to 00b Set OCD2 bit to 0 (select XIN clock) End OCD3 to OCD0: Bits in OCD register Figure 10.14 Procedure for Switching Clock Source from Low-Speed On-Chip Oscillator to XIN Clock Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 93 of 450 R8C/2K Group, R8C/2L Group 10. Clock Generation Circuit Interrupt sources judgment OCD3 = 1 ? (XIN clock stopped) NO YES OCD1 = 1 (oscillation stop detection interrupt enabled) and OCD2 = 1 (on-chip oscillator clock selected as system clock) ? NO YES VW2C3 = 1 ? (Watchdog timer underflow) NO YES VW2C2 = 1 ? (passing Vdet2) NO YES Set OCD1 bit to 0 (oscillation stop detection interrupt disabled). (1) To oscillation stop detection interrupt routine To watchdog timer interrupt routine To voltage monitor 2 interrupt routine To voltage monitor 1 interrupt routine NOTE: 1. This disables multiple oscillation stop detection interrupts. OCD1 to OCD3: Bits in OCD register VW2C2, VW2C3: Bits in VW2C register Figure 10.15 Example of Determining Interrupt Source for Oscillation Stop Detection, Watchdog Timer, Voltage Monitor 1, or Voltage Monitor 2 Interrupt Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 94 of 450 R8C/2K Group, R8C/2L Group 10.6 10. Clock Generation Circuit Notes on Clock Generation Circuit 10.6.1 Stop Mode When entering stop mode, set the FMR01 bit in the FMR0 register to 0 (CPU rewrite mode disabled) and the CM10 bit in the CM1 register to 1 (stop mode). An instruction queue pre-reads 4 bytes from the instruction which sets the CM10 bit to 1 (stop mode) and the program stops. Insert at least 4 NOP instructions following the JMP.B instruction after the instruction which sets the CM10 bit to 1. * Program example to enter stop mode BCLR BSET FSET BSET JMP.B LABEL_001 : NOP NOP NOP NOP 10.6.2 1,FMR0 0,PRCR I 0,CM1 LABEL_001 ; CPU rewrite mode disabled ; Protect disabled ; Enable interrupt ; Stop mode Wait Mode When entering wait mode, set the FMR01 bit in the FMR0 register to 0 (CPU rewrite mode disabled) and execute the WAIT instruction. An instruction queue pre-reads 4 bytes from the WAIT instruction and the program stops. Insert at least 4 NOP instructions after the WAIT instruction. * Program example to execute the WAIT instruction BCLR 1,FMR0 FSET I WAIT NOP NOP NOP NOP 10.6.3 ; CPU rewrite mode disabled ; Enable interrupt ; Wait mode Oscillation Stop Detection Function Since the oscillation stop detection function cannot be used if the XIN clock frequency is 2 MHz or below, set bits OCD1 to OCD0 to 00b. 10.6.4 Oscillation Circuit Constants Ask the manufacturer of the oscillator to specify the best oscillation circuit constants for your system. To use this MCU with supply voltage below VCC = 2.7 V, it is recommended to set the CM11 bit in the CM1 register to 1 (on-chip feedback resistor disabled), the CM15 bit to 1 (high drive capacity), and connect the feedback resistor to the chip externally. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 95 of 450 R8C/2K Group, R8C/2L Group 11. Protection 11. Protection The protection function protects important registers from being easily overwritten when a program runs out of control. Figure 11.1 shows the PRCR Register. The registers protected by the PRCR register are listed below. * Registers protected by PRC0 bit: Registers CM0, CM1, OCD, FRA0, FRA1, and FRA2 * Registers protected by PRC1 bit: Registers PM0 and PM1 * Registers protected by PRC2 bit: PD0 register * Registers protected by PRC3 bit: Registers VCA2, VW0C, VW1C, and VW2C Protect Register b7 b6 b5 b4 b3 b2 b1 b0 0 0 Symbol PRCR Bit Symbol Address 000Ah Bit Name Protect bit 0 PRC0 Protect bit 1 PRC1 Protect bit 2 PRC2 Protect bit 3 PRC3 After Reset 00h Function Writing to registers CM0, CM1, OCD, FRA0, FRA1, and FRA2 is enabled. 0 : Disables w riting 1 : Enables w riting RW RW Writing to registers PM0 and PM1 is enabled. 0 : Disables w riting 1 : Enables w riting RW Writing to the PD0 register is enabled. 0 : Disables w riting 1 : Enables w riting(1) RW Writing to registers VCA2, VW0C, VW1C, and VW2C is enabled. 0 : Disables w riting 1 : Enables w riting RW -- (b5-b4) Reserved bits Set to 0. -- (b7-b6) Reserved bits When read, the content is 0. RW RO NOTE: 1. This bit is set to 0 after w riting 1 to the PRC2 bit and executing a w rite to any address. Since the other bits are not set to 0, set them to 0 by a program. Figure 11.1 PRCR Register Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 96 of 450 R8C/2K Group, R8C/2L Group 12. Interrupts 12. Interrupts 12.1 Interrupt Overview 12.1.1 Types of Interrupts Figure 12.1 shows the types of Interrupts. Software (non-maskable interrupts) Interrupts Special (non-maskable interrupts) Hardware Peripheral functions(1) (maskable interrupts) Undefined instruction (UND instruction) Overflow (INTO instruction) BRK instruction INT instruction Watchdog timer Oscillation stop detection Voltage monitor 1 Voltage monitor 2 Single step(2) Address break(2) Address match NOTES: 1. Peripheral function interrupts in the MCU are used to generate peripheral interrupts. 2. Do not use this interrupt. This is for use with development tools only. Figure 12.1 Interrupts * Maskable Interrupts: * Non-Maskable Interrupts: Rev.1.10 Dec 21, 2007 REJ09B0406-0110 The interrupt enable flag (I flag) enables or disables these interrupts. The interrupt priority order can be changed based on the interrupt priority level. The interrupt enable flag (I flag) does not enable or disable these interrupts. The interrupt priority order cannot be changed based on interrupt priority level. Page 97 of 450 R8C/2K Group, R8C/2L Group 12.1.2 12. Interrupts Software Interrupts A software interrupt is generated when an instruction is executed. Software interrupts are non-maskable. 12.1.2.1 Undefined Instruction Interrupt The undefined instruction interrupt is generated when the UND instruction is executed. 12.1.2.2 Overflow Interrupt The overflow interrupt is generated when the O flag is set to 1 (arithmetic operation overflow) and the INTO instruction is executed. Instructions that set the O flag are: ABS, ADC, ADCF, ADD, CMP, DIV, DIVU, DIVX, NEG, RMPA, SBB, SHA, and SUB. 12.1.2.3 BRK Interrupt A BRK interrupt is generated when the BRK instruction is executed. 12.1.2.4 INT Instruction Interrupt An INT instruction interrupt is generated when the INT instruction is executed. The INT instruction can select software interrupt numbers 0 to 63. Software interrupt numbers 3 to 31 are assigned to the peripheral function interrupt. Therefore, the MCU executes the same interrupt routine when the INT instruction is executed as when a peripheral function interrupt is generated. For software interrupt numbers 0 to 31, the U flag is saved to the stack during instruction execution and the U flag is set to 0 (ISP selected) before the interrupt sequence is executed. The U flag is restored from the stack when returning from the interrupt routine. For software interrupt numbers 32 to 63, the U flag does not change state during instruction execution, and the selected SP is used. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 98 of 450 R8C/2K Group, R8C/2L Group 12.1.3 12. Interrupts Special Interrupts Special interrupts are non-maskable. 12.1.3.1 Watchdog Timer Interrupt The watchdog timer interrupt is generated by the watchdog timer. For details, refer to 15. Watchdog Timer. 12.1.3.2 Oscillation Stop Detection Interrupt The oscillation stop detection interrupt is generated by the oscillation stop detection function. For details of the oscillation stop detection function, refer to 10. Clock Generation Circuit. 12.1.3.3 Voltage Monitor 1 Interrupt The voltage monitor 1 interrupt is generated by the voltage detection circuit. For details of the voltage detection circuit, refer to 6. Voltage Detection Circuit. 12.1.3.4 Voltage Monitor 2 Interrupt The voltage monitor 2 interrupt is generated by the voltage detection circuit. For details of the voltage detection circuit, refer to 6. Voltage Detection Circuit. 12.1.3.5 Single-Step Interrupt, and Address Break Interrupt Do not use these interrupts. They are for use by development tools only. 12.1.3.6 Address Match Interrupt The address match interrupt is generated immediately before executing an instruction that is stored at an address indicated by registers RMAD0 to RMAD1 when the AIER0 or AIER1 bit in the AIER register is set to 1 (address match interrupt enable). For details of the address match interrupt, refer to 12.4 Address Match Interrupt. 12.1.4 Peripheral Function Interrupt The peripheral function interrupt is generated by the internal peripheral function of the MCU and is a maskable interrupt. Refer to Table 12.2 Relocatable Vector Tables for sources of the peripheral function interrupt. For details of peripheral functions, refer to the descriptions of individual peripheral functions. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 99 of 450 R8C/2K Group, R8C/2L Group 12.1.5 12. Interrupts Interrupts and Interrupt Vectors There are 4 bytes in each vector. Set the starting address of an interrupt routine in each interrupt vector. When an interrupt request is acknowledged, the CPU branches to the address set in the corresponding interrupt vector. Figure 12.2 shows an Interrupt Vector. MSB LSB Vector address (L) Low address Mid address Vector address (H) Figure 12.2 12.1.5.1 0000 High address 0000 0000 Interrupt Vector Fixed Vector Tables The fixed vector tables are allocated addresses 0FFDCh to 0FFFFh. Table 12.1 lists the Fixed Vector Tables. The vector addresses (H) of fixed vectors are used by the ID code check function. For details, refer to 20.3 Functions to Prevent Rewriting of Flash Memory. Table 12.1 Fixed Vector Tables Interrupt Source Undefined instruction Overflow BRK instruction Address match Single step(1) Watchdog timer, Oscillation stop detection, Voltage monitor 1, Voltage monitor 2 Address break(1) (Reserved) Reset Vector Addresses Remarks Reference Address (L) to (H) 0FFDCh to 0FFDFh Interrupt on UND R8C/Tiny Series Software instruction Manual 0FFE0h to 0FFE3h Interrupt on INTO instruction 0FFE4h to 0FFE7h If the content of address 0FFE7h is FFh, program execution starts from the address shown by the vector in the relocatable vector table. 0FFE8h to 0FFEBh 12.4 Address Match Interrupt 0FFECh to 0FFEFh 0FFF0h to 0FFF3h 15. Watchdog Timer 10. Clock Generation Circuit 6. Voltage Detection Circuit 0FFF4h to 0FFF7h 0FFF8h to 0FFFBh 0FFFCh to 0FFFFh 5. Resets NOTE: 1. Do not use these interrupts. They are for use by development tools only. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 100 of 450 R8C/2K Group, R8C/2L Group 12.1.5.2 12. Interrupts Relocatable Vector Tables The relocatable vector tables occupy 256 bytes beginning from the starting address set in the INTB register. Table 12.2 lists the Relocatable Vector Tables. Table 12.2 Relocatable Vector Tables +28 to +31 (001Ch to 001Fh) +32 to +35 (0020h to 0023h) Software Interrupt Control Interrupt Reference Register Number 0 - R8C/Tiny Series Software Manual 1 to 6 - - 7 TRCIC 16.3 Timer RC 8 TRD0IC 16.4 Timer RD +36 to +39 (0024h to 0027h) 9 TRD1IC +96 to +99 (0060h to 0063h) +100 to +103 (0064h to 0067h) 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 - S2TIC S2RIC KUPIC ADIC - - S0TIC S0RIC - - - TRAIC - TRBIC INT1IC INT3 (Reserved) (Reserved) +104 to +107 (0068h to 006Bh) 26 INT3IC INT0 (Reserved) (Reserved) Software interrupt(2) +116 to +119 (0074h to 0077h) 27 28 29 - - INT0IC Vector Addresses(1) Address (L) to Address (H) Interrupt Source BRK instruction(2) (Reserved) Timer RC Timer RD (channel 0) Timer RD (channel 1) (Reserved) UART2 transmit UART2 receive Key input A/D (Reserved) (Reserved) UART0 transmit UART0 receive (Reserved) (Reserved) (Reserved) Timer RA (Reserved) Timer RB INT1 +0 to +3 (0000h to 0003h) +44 to +47 (002Ch to 002Fh) +48 to +51 (0030h to 0033h) +52 to +55 (0034h to 0037h) +56 to +59 (0038h to 003Bh) +68 to +71 (0044h to 0047h) +72 to +75 (0048h to 004Bh) +88 to +91 (0058h to 005Bh) 30 31 +128 to +131 (0080h to 0083h) to 32 to 63 +252 to +255 (00FCh to 00FFh) NOTES: 1. These addresses are relative to those in the INTB register. 2. The I flag does not disable these interrupts. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 101 of 450 - - - - 17. Serial Interface 12.3 Key Input Interrupt 19. A/D Converter - - 17. Serial Interface - - - 16.1 Timer RA - 16.2 Timer RB 12.2 INT Interrupt - - 12.2 INT Interrupt - - R8C/Tiny Series Software Manual R8C/2K Group, R8C/2L Group 12.1.6 12. Interrupts Interrupt Control The following describes enabling and disabling the maskable interrupts and setting the priority for acknowledgement. The explanation does not apply to nonmaskable interrupts. Use the I flag in the FLG register, IPL, and bits ILVL2 to ILVL0 in each interrupt control register to enable or disable maskable interrupts. Whether an interrupt is requested is indicated by the IR bit in each interrupt control register. Figure 12.3 shows the Interrupt Control Register, Figure 12.4 shows Registers TRCIC, TRD0IC, and TRD1IC and Figure 12.5 shows the INTiIC Register. Interrupt Control Register(2) b7 b6 b5 b4 b3 b2 b1 b0 Symbol S2TIC S2RIC KUPIC ADIC S0TIC S0RIC TRAIC TRBIC Bit Symbol Address 004Bh 004Ch 004Dh 004Eh 0051h 0052h 0056h After Reset XXXXX000b XXXXX000b XXXXX000b XXXXX000b XXXXX000b XXXXX000b XXXXX000b 0058h XXXXX000b Bit Name Interrupt priority level select bits 0 0 0 : Level 0 (interrupt disable) 0 0 1 : Level 1 0 1 0 : Level 2 0 1 1 : Level 3 1 0 0 : Level 4 1 0 1 : Level 5 1 1 0 : Level 6 1 1 1 : Level 7 ILVL0 ILVL1 ILVL2 IR -- (b7-b4) Function Interrupt request bit RW b2 b1 b0 0 : Requests no interrupt 1 : Requests interrupt Nothing is assigned. If necessary, set to 0. When read, the content is undefined. RW RW RW RW(1) -- NOTES: 1. Only 0 can be w ritten to the IR bit. Do not w rite 1. 2. Rew rite the interrupt control register w hen the interrupt request w hich is applicable for the register is not generated. Refer to 12.6.5 Changing Interrupt Control Register Contents. Figure 12.3 Interrupt Control Register Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 102 of 450 R8C/2K Group, R8C/2L Group 12. Interrupts Interrupt Control Register(1) b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRCIC TRD0IC TRD1IC Bit Symbol Address 0047h 0048h After Reset XXXXX000b XXXXX000b 0049h XXXXX000b Bit Name Interrupt priority level select bits ILVL0 ILVL1 ILVL2 IR -- (b7-b4) Interrupt request bit Function RW b2 b1 b0 0 0 0 : Level 0 (interrupt disable) 0 0 1 : Level 1 0 1 0 : Level 2 0 1 1 : Level 3 1 0 0 : Level 4 1 0 1 : Level 5 1 1 0 : Level 6 1 1 1 : Level 7 RW 0 : Requests no interrupt 1 : Requests interrupt RO Nothing is assigned. If necessary, set to 0. When read, the content is undefined. RW RW -- NOTE: 1. Rew rite the interrupt control register w hen the interrupt request w hich is applicable for the register is not generated. Refer to 12.6.5 Changing Interrupt Control Register Contents. Figure 12.4 Registers TRCIC, TRD0IC, and TRD1IC Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 103 of 450 R8C/2K Group, R8C/2L Group 12. Interrupts INTi Interrupt Control Register (i=0, 1, 3)(2) b7 b6 b5 b4 b3 b2 b1 b0 0 Symbol INT1IC INT3IC Address 0059h 005Ah After Reset XX00X000b XX00X000b INT0IC 005Dh XX00X000b Bit Symbol Bit Name Interrupt priority level select bits 0 0 0 : Level 0 (interrupt disable) 0 0 1 : Level 1 0 1 0 : Level 2 0 1 1 : Level 3 1 0 0 : Level 4 1 0 1 : Level 5 1 1 0 : Level 6 1 1 1 : Level 7 ILVL0 ILVL1 ILVL2 IR POL -- (b5) -- (b7-b6) Function RW b2 b1 b0 RW RW RW Interrupt request bit 0 : Requests no interrupt 1 : Requests interrupt RW(1) Polarity sw itch bit(4) 0 : Selects falling edge 1 : Selects rising edge(3) RW Reserved bit Set to 0. Nothing is assigned. If necessary, set to 0. When read, the content is undefined. RW -- NOTES: 1. Only 0 can be w ritten to the IR bit. (Do not w rite 1.) 2. Rew rite the interrupt control register w hen the interrupt request w hich is applicable for the register is not generated. Refer to 12.6.5 Changing Interrupt Control Register Contents . 3. If the INTiPL bit in the INTEN register is set to 1 (both edges), set the POL bit to 0 (selects falling edge). 4. The IR bit may be set to 1 (requests interrupt) w hen the POL bit is rew ritten. Refer to 12.6.4 Changing Interrupt Sources. Figure 12.5 INTiIC Register Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 104 of 450 R8C/2K Group, R8C/2L Group 12.1.6.1 12. Interrupts I Flag The I flag enables or disables maskable interrupts. Setting the I flag to 1 (enabled) enables maskable interrupts. Setting the I flag to 0 (disabled) disables all maskable interrupts. 12.1.6.2 IR Bit The IR bit is set to 1 (interrupt requested) when an interrupt request is generated. Then, when the interrupt request is acknowledged and the CPU branches to the corresponding interrupt vector, the IR bit is set to 0 (= interrupt not requested). The IR bit can be set to 0 by a program. Do not write 1 to this bit. However, the IR bit operations of the timer RD Interrupt, Clock Synchronous Serial I/O with Chip Select Interrupt and the I2C bus Interface Interrupt are different. Refer to 12.5 Timer RC Interrupt, Timer RD Interrupt (Interrupts with Multiple Interrupt Request Sources). 12.1.6.3 Bits ILVL2 to ILVL0 and IPL Interrupt priority levels can be set using bits ILVL2 to ILVL0. Table 12.3 lists the Settings of Interrupt Priority Levels and Table 12.4 lists the Interrupt Priority Levels Enabled by IPL. The following are conditions under which an interrupt is acknowledged: * I flag = 1 * IR bit = 1 * Interrupt priority level > IPL The I flag, IR bit, bits ILVL2 to ILVL0, and IPL are independent of each other. They do not affect one another. Table 12.3 ILVL2 to ILVL0 Bits 000b 001b 010b 011b 100b 101b 110b 111b Settings of Interrupt Priority Levels Interrupt Priority Level Priority Order Level 0 (interrupt disabled) Level 1 Level 2 Level 3 Level 4 Level 5 Level 6 Level 7 - Low Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 105 of 450 High Table 12.4 IPL 000b 001b 010b 011b 100b 101b 110b 111b Interrupt Priority Levels Enabled by IPL Enabled Interrupt Priority Levels Interrupt level 1 and above Interrupt level 2 and above Interrupt level 3 and above Interrupt level 4 and above Interrupt level 5 and above Interrupt level 6 and above Interrupt level 7 and above All maskable interrupts are disabled R8C/2K Group, R8C/2L Group 12.1.6.4 12. Interrupts Interrupt Sequence An interrupt sequence is performed between an interrupt request acknowledgement and interrupt routine execution. When an interrupt request is generated while an instruction is being executed, the CPU determines its interrupt priority level after the instruction is completed. The CPU starts the interrupt sequence from the following cycle. However, for the SMOVB, SMOVF, SSTR, or RMPA instruction if an interrupt request is generated while the instruction is being executed, the MCU suspends the instruction to start the interrupt sequence. The interrupt sequence is performed as indicated below. Figure 12.6 shows the Time Required for Executing Interrupt Sequence. (1) The CPU gets interrupt information (interrupt number and interrupt request level) by reading address 00000h. The IR bit for the corresponding interrupt is set to 0 (interrupt not requested).(2) (2) The FLG register is saved to a temporary register(1) in the CPU immediately before entering the interrupt sequence. (3) The I, D and U flags in the FLG register are set as follows: The I flag is set to 0 (interrupts disabled). The D flag is set to 0 (single-step interrupt disabled). The U flag is set to 0 (ISP selected). However, the U flag does not change state if an INT instruction for software interrupt number 32 to 63 is executed. (4) The CPU's internal temporary register(1) is saved to the stack. (5) The PC is saved to the stack. (6) The interrupt priority level of the acknowledged interrupt is set in the IPL. (7) The starting address of the interrupt routine set in the interrupt vector is stored in the PC. After the interrupt sequence is completed, instructions are executed from the starting address of the interrupt routine. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 CPU Clock Address Bus Data Bus Address 0000h Undefined Interrupt information RD Undefined SP-2 SP-1 SP-4 SP-2 SP-1 SP-4 contents contents contents SP-3 SP-3 contents VEC VEC contents VEC+1 VEC+1 contents VEC+2 PC VEC+2 contents Undefined WR The indeterminate state depends on the instruction queue buffer. A read cycle occurs when the instruction queue buffer is ready to acknowledge instructions. Figure 12.6 Time Required for Executing Interrupt Sequence NOTES: 1. This register cannot be accessed by the user. 2. Refer to 12.5 Timer RC Interrupt, Timer RD Interrupt (Interrupts with Multiple Interrupt Request Sources) for the IR bit operations of the timer RC Interrupt, timer RD Interrupt, Clock Synchronous Serial I/O with Chip Select Interrupt, and the I2C bus Interface Interrupt. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 106 of 450 R8C/2K Group, R8C/2L Group 12.1.6.5 12. Interrupts Interrupt Response Time Figure 12.7 shows the Interrupt Response Time. The interrupt response time is the period between an interrupt request generation and the execution of the first instruction in the interrupt routine. The interrupt response time includes the period between interrupt request generation and the completion of execution of the instruction (refer to (a) in Figure 12.7) and the period required to perform the interrupt sequence (20 cycles, refer to (b) in Figure 12.7). Interrupt request is generated. Interrupt request is acknowledged. Time Instruction (a) Instruction in interrupt routine Interrupt sequence 20 cycles (b) Interrupt response time (a) Period between interrupt request generation and the completion of execution of an instruction. The length of time varies depending on the instruction being executed. The DIVX instruction requires the longest time, 30 cycles (assuming no wait states and that a register is set as the divisor). (b) 21 cycles for address match and single-step interrupts. Figure 12.7 12.1.6.6 Interrupt Response Time IPL Change when Interrupt Request is Acknowledged When an interrupt request of a maskable interrupt is acknowledged, the interrupt priority level of the acknowledged interrupt is set in the IPL. When a software interrupt or special interrupt request is acknowledged, the level listed in Table 12.5 is set in the IPL. Table 12.5 lists the IPL Value When Software or Special Interrupt Is Acknowledged. Table 12.5 IPL Value When Software or Special Interrupt Is Acknowledged Interrupt Source Watchdog timer, oscillation stop detection, voltage monitor 1, voltage monitor 2, Address break Software, address match, single-step Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 107 of 450 Value Set in IPL 7 Not changed R8C/2K Group, R8C/2L Group 12.1.6.7 12. Interrupts Saving a Register In the interrupt sequence, the FLG register and PC are saved to the stack. After an extended 16 bits, 4 high-order bits in the PC and 4 high-order (IPL) and 8 low-order bits in the FLG register, are saved to the stack, the 16 low-order bits in the PC are saved. Figure 12.8 shows the Stack State Before and After Acknowledgement of Interrupt Request. The other necessary registers are saved by a program at the beginning of the interrupt routine. The PUSHM instruction can save several registers in the register bank being currently used(1) with a single instruction. NOTE: 1. Selectable from registers R0, R1, R2, R3, A0, A1, SB, and FB. Stack Address Stack Address MSB LSB MSB LSB m-4 m-4 PCL m-3 m-3 PCM m-2 m-2 FLGL m-1 m-1 m Previous stack contents m+1 Previous stack contents [SP] SP value before interrupt is generated m m+1 Stack state before interrupt request is acknowledged FLGH [SP] New SP value PCH Previous stack contents Previous stack contents PCH PCM PCL FLGH FLGL : 4 high-order bits of PC : 8 middle-order bits of PC : 8 low-order bits of PC : 4 high-order bits of FLG : 8 low-order bits of FLG Stack state after interrupt request is acknowledged NOTE: 1.When executing software number 32 to 63 INT instructions, this SP is specified by the U flag. Otherwise it is ISP. Figure 12.8 Stack State Before and After Acknowledgement of Interrupt Request The register saving operation, which is performed as part of the interrupt sequence, saved in 8 bits at a time in four steps. Figure 12.9 shows the Register Saving Operation. Stack Address Sequence in which order registers are saved [SP]-5 [SP]-4 PCL (3) [SP]-3 PCM (4) [SP]-2 FLGL (1) Saved, 8 bits at a time [SP]-1 FLGH PCH (2) [SP] Completed saving registers in four operations. PCH PCM PCL FLGH FLGL NOTE: 1. [SP] indicates the initial value of the SP when an interrupt request is acknowledged. After registers are saved, the SP content is [SP] minus 4. When executing software number 32 to 63 INT instructions, this SP is specified by the U flag. Otherwise it is ISP. Figure 12.9 Register Saving Operation Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 108 of 450 : 4 high-order bits of PC : 8 middle-order bits of PC : 8 low-order bits of PC : 4 high-order bits of FLG : 8 low-order bits of FLG R8C/2K Group, R8C/2L Group 12.1.6.8 12. Interrupts Returning from an Interrupt Routine When the REIT instruction is executed at the end of an interrupt routine, the FLG register and PC, which have been saved to the stack, are automatically restored. The program, that was running before the interrupt request was acknowledged, starts running again. Restore registers saved by a program in an interrupt routine using the POPM instruction or others before executing the REIT instruction. 12.1.6.9 Interrupt Priority If two or more interrupt requests are generated while a single instruction is being executed, the interrupt with the higher priority is acknowledged. Set bits ILVL2 to ILVL0 to select the desired priority level for maskable interrupts (peripheral functions). However, if two or more maskable interrupts have the same priority level, their interrupt priority is resolved by hardware, and the higher priority interrupts acknowledged. The priority levels of special interrupts, such as reset (reset has the highest priority) and watchdog timer, are set by hardware. Figure 12.10 shows the Priority Levels of Hardware Interrupts. The interrupt priority does not affect software interrupts. The MCU jumps to the interrupt routine when the instruction is executed. Reset High Address break Watchdog timer Oscillation stop detection Voltage monitor 1 Voltage monitor 2 Peripheral function Single step Address match Figure 12.10 Priority Levels of Hardware Interrupts Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 109 of 450 Low R8C/2K Group, R8C/2L Group 12. Interrupts 12.1.6.10 Interrupt Priority Judgement Circuit The interrupt priority judgement circuit selects the highest priority interrupt, as shown in Figure 12.11. Priority level of interrupt Level 0 (default value) Highest INT3 Timer RB Timer RA INT0 INT1 Timer RC Priority of peripheral function interrupts (if priority levels are same) UART0 receive A/D conversion UART2 receive Timer RD0 UART0 transmit Key input UART2 transmit Timer RD1 Lowest IPL Interrupt request level judgment output signal I flag Address match Watchdog timer Oscillation stop detection Voltage monitor 1 Voltage monitor 2 Figure 12.11 Interrupt Priority Level Judgement Circuit Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 110 of 450 Interrupt request acknowledged R8C/2K Group, R8C/2L Group 12.2 12. Interrupts INT Interrupt 12.2.1 INTi Interrupt (i = 0, 1, 3) The INTi interrupt is generated by an INTi input. When using the INTi interrupt, the INTiEN bit in the INTEN register is set to 1 (enable). The edge polarity is selected using the INTiPL bit in the INTEN register and the POL bit in the INTiIC register. Inputs can be passed through a digital filter with three different sampling clocks. The INT0 pin is shared with the pulse output forced cutoff of timer RC and timer RD, and the external trigger input of timer RB. Figure 12.12 shows the PMR Register, Figure 12.13 shows the INTEN Register, Figure 12.14 shows the INTF Register, and Figure 12.15 shows the TRAIOC Register. Port Mode Register b7 b0 Symbol PMR _____ Address 00F8h Function After Reset 00h RW Set to "04h" w hen using INT3. Do not set values other than "04h". When read, its content is undefined. Figure 12.12 WO PMR Register External Input Enable Register b7 b6 b5 b4 b3 b2 b1 b0 0 0 Symbol INTEN Bit Symbol INT0EN Address 00F9h Bit Name _____ INT0 input enable bit RW 0 : One edge 1 : Both edges RW 0 : Disable 1 : Enable RW INT1 input polarity select bit(1,2) 0 : One edge 1 : Both edges RW Reserved bit Set to 0. INT0 input polarity select bit(1,2) _____ INT1EN INT1 input enable bit _____ INT1PL -- (b5-b4) _____ INT3EN INT3 input enable bit _____ INT3PL RW 0 : Disable 1 : Enable _____ INT0PL After Reset 00h Function INT3 input polarity select bit(1,2) RW 0 : Disable 1 : Enable RW 0 : One edge 1 : Both edges RW NOTES: 1. When setting the INTiPL bit (i = 0, 1, 3) to 1 (both edges), set the POL bit in the INTiIC register to 0 (selects falling edge). 2. The IR bit in the INTiIC register may be set to 1 (requests interrupt) w hen the INTiPL bit is rew ritten. Refer to 12.6.4 Changing Interrupt Sources. Figure 12.13 INTEN Register Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 111 of 450 R8C/2K Group, R8C/2L Group 12. Interrupts _____ INT Input Filter Select Register b7 b6 b5 b4 b3 b2 b1 b0 0 0 Symbol INTF Bit Symbol Address 00FAh Bit Name _____ INT0F0 INT0 input filter select bits INT0F1 _____ INT1F0 INT1 input filter select bits INT1F1 -- (b5-b4) INT3F0 0 0 : No filter 0 1 : Filter w ith f1 sampling 1 0 : Filter w ith f8 sampling 1 1 : Filter w ith f32 sampling RW RW b3 b2 0 0 : No filter 0 1 : Filter w ith f1 sampling 1 0 : Filter w ith f8 sampling 1 1 : Filter w ith f32 sampling Set to 0. _____ b7 b6 INT3 input filter select bits RW b1 b0 Reserved bit INT3F1 Figure 12.14 After Reset 00h Function 0 0 : No filter 0 1 : Filter w ith f1 sampling 1 0 : Filter w ith f8 sampling 1 1 : Filter w ith f32 sampling RW RW RW RW RW INTF Register Timer RA I/O Control Register b7 b6 b5 b4 b3 b2 b1 b0 0 Symbol TRAIOC Bit Symbol TEDGSEL TOPCR -- (b2) Address 0101h Bit Name TRAIO polarity sw itch bit TRAIO output control bit Reserved bit _____ TIOSEL TIPF0 TIPF1 -- (b7-b6) Figure 12.15 Set to 0. RW RW _____ 0 : INT1/TRAIO pin (P1_7) _____ 1 : INT1/TRAIO pin (P1_5) TRAIO input filter select bits Function varies depending on operating mode. Nothing is assigned. If necessary, set to 0. When read, the content is 0. Page 112 of 450 RW RW INT1/TRAIO select bit TRAIOC Register Rev.1.10 Dec 21, 2007 REJ09B0406-0110 After Reset 00h Function Function varies depending on operating mode. RW RW -- R8C/2K Group, R8C/2L Group 12.2.2 12. Interrupts INTi Input Filter (i = 0, 1, 3) The INTi input contains a digital filter. The sampling clock is selected by bits INTiF1 to INTiF0 in the INTF register. The INTi level is sampled every sampling clock cycle and if the sampled input level matches three times, the IR bit in the INTiIC register is set to 1 (interrupt requested). Figure 12.16 shows the Configuration of INTi Input Filter. Figure 12.17 shows an Operating Example of INTi Input Filter. INTiF1 to INTiF0 f1 f8 f32 INTi Port direction register(1) = 01b = 10b Sampling clock = 11b INTiEN Digital filter (input level matches 3x) Other than INTiF1 to INTiF0 = 00b = 00b INTi interrupt INTiPL = 0 Both edges detection INTiPL = 1 circuit INTiF0, INTiF1: Bits in INTF register INTiEN, INTiPL: Bits in INTEN register i = 0, 1, 3 NOTE: 1. INT0: Port P4_5 direction register INT1: Port P1_5 direction register when using the P1_5 pin Port P1_7 direction register when using the P1_7 pin INT3: Port P3_3 direction register Figure 12.16 Configuration of INTi Input Filter INTi input Sampling timing IR bit in INTiIC register Set to 0 by a program This is an operation example when bits INTiF1 to INTiF0 in the INTiF register are set to 01b, 10b, or 11b (digital filter enabled). i = 0, 1, 3 Figure 12.17 Operating Example of INTi Input Filter Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 113 of 450 R8C/2K Group, R8C/2L Group 12.3 12. Interrupts Key Input Interrupt A key input interrupt request is generated by one of the input edges of pins K10 to K13. The key input interrupt can be used as a key-on wake-up function to exit wait or stop mode. The KIiEN (i = 0 to 3) bit in the KIEN register can select whether or not the pins are used as KIi input. The KIiPL bit in the KIEN register can select the input polarity. When inputting "L" to the KIi pin which sets the KIiPL bit to 0 (falling edge), the input of the other pins K10 to K13 is not detected as interrupts. Also, when inputting "H" to the KIi pin, which sets the KIiPL bit to 1 (rising edge), the input of the other pins K10 to K13 is not detected as interrupts. Figure 12.18 shows a Block Diagram of Key Input Interrupt. PU02 bit in PUR0 register KUPIC register Pull-up transistor PD1_3 bit in PD1 register KI3EN bit PD1_3 bit KI3PL = 0 KI3 KI3PL = 1 Pull-up transistor KI2EN bit PD1_2 bit KI2PL = 0 Interrupt control circuit KI2 KI2PL = 1 Pull-up transistor Key input interrupt request KI1EN bit PD1_1 bit KI1PL = 0 KI1 KI1PL = 1 Pull-up transistor KI0EN bit PD1_0 bit KI0PL = 0 KI0 KI0PL = 1 Figure 12.18 Block Diagram of Key Input Interrupt Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 114 of 450 KI0EN, KI1EN, KI2EN, KI3EN, KI0PL, KI1PL, KI2PL, KI3PL: Bits in KIEN register PD1_0, PD1_1, PD1_2, PD1_3: Bits in PD1 register R8C/2K Group, R8C/2L Group 12. Interrupts Key Input Enable Register(1) b7 b6 b5 b4 b3 b2 b1 b0 Symbol KIEN Bit Symbol KI0EN KI0PL KI1EN KI1PL KI2EN KI2PL KI3EN KI3PL Address 00FBh Bit Name KI0 input enable bit After Reset 00h Function RW KI0 input polarity select bit 0 : Falling edge 1 : Rising edge RW KI1 input enable bit 0 : Disable 1 : Enable RW KI1 input polarity select bit 0 : Falling edge 1 : Rising edge RW KI2 input enable bit 0 : Disable 1 : Enable RW KI2 input polarity select bit 0 : Falling edge 1 : Rising edge RW KI3 input enable bit 0 : Disable 1 : Enable RW KI3 input polarity select bit 0 : Falling edge 1 : Rising edge RW NOTE: 1. The IR bit in the KUPIC register may be set to 1 (requests interrupt) w hen the KIEN register is rew ritten. Refer to 12.6.4 Changing Interrupt Sources. Figure 12.19 KIEN Register Rev.1.10 Dec 21, 2007 REJ09B0406-0110 RW 0 : Disable 1 : Enable Page 115 of 450 R8C/2K Group, R8C/2L Group 12.4 12. Interrupts Address Match Interrupt An address match interrupt request is generated immediately before execution of the instruction at the address indicated by the RMADi register (i = 0 or 1). This interrupt is used as a break function by the debugger. When using the on-chip debugger, do not set an address match interrupt (registers of AIER, RMAD0, and RMAD1 and fixed vector tables) in a user system. Set the starting address of any instruction in the RMADi register. Bits AIER0 and AIER1 in the AIER0 register can be used to select enable or disable of the interrupt. The I flag and IPL do not affect the address match interrupt. The value of the PC (Refer to 12.1.6.7 Saving a Register for the value of the PC) which is saved to the stack when an address match interrupt is acknowledged varies depending on the instruction at the address indicated by the RMADi register. (The appropriate return address is not saved on the stack.) When returning from the address match interrupt, return by one of the following means: * Change the content of the stack and use the REIT instruction. * Use an instruction such as POP to restore the stack as it was before the interrupt request was acknowledged. Then use a jump instruction. Table 12.6 lists the Values of PC Saved to Stack when Address Match Interrupt is Acknowledged. Figure 12.20 shows Registers AIER and RMAD0 to RMAD1. Table 12.6 Values of PC Saved to Stack when Address Match Interrupt is Acknowledged Address Indicated by RMADi Register (i = 0 or 1) * Instruction with 2-byte operation code(2) * Instruction with 1-byte operation code(2) ADD.B:S #IMM8,dest SUB.B:S #IMM8,dest AND.B:S #IMM8,dest OR.B:S #IMM8,dest MOV.B:S #IMM8,dest STZ #IMM8,dest STNZ #IMM8,dest STZX #IMM81,#IMM82,dest CMP.B:S #IMM8,dest PUSHM src POPM dest JMPS #IMM8 JSRS #IMM8 MOV.B:S #IMM,dest (however, dest = A0 or A1) * Instructions other than the above PC Value Saved(1) Address indicated by RMADi register + 2 Address indicated by RMADi register + 1 NOTES: 1. Refer to the 12.1.6.7 Saving a Register for the PC value saved. 2. Operation code: Refer to the R8C/Tiny Series Software Manual (REJ09B0001). Chapter 4. Instruction Code/Number of Cycles contains diagrams showing operation code below each syntax. Operation code is shown in the bold frame in the diagrams. Table 12.7 Correspondence Between Address Match Interrupt Sources and Associated Registers Address Match Interrupt Source Address Match Interrupt Enable Bit Address Match Interrupt Register Address match interrupt 0 AIER0 RMAD0 Address match interrupt 1 AIER1 RMAD1 Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 116 of 450 R8C/2K Group, R8C/2L Group 12. Interrupts Address Match Interrupt Enable Register b7 b6 b5 b4 b3 b2 b1 b0 Symbol AIER Bit Symbol AIER0 AIER1 -- (b7-b2) Address 0013h Bit Name Address match interrupt 0 enable bit 0 : Disable 1 : Enable After Reset 00h Function RW RW Address match interrupt 1 enable bit 0 : Disable 1 : Enable RW Nothing is assigned. If necessary, set to 0. When read, the content is 0. -- Address Match Interrupt Register i (i = 0 or 1) (b23) b7 (b19) b3 (b16) (b15) b0 b7 (b8) b0 b7 b0 Symbol RMAD0 RMAD1 Address 0012h-0010h 0016h-0014h Function Address setting register for address match interrupt -- Nothing is assigned. If necessary, set to 0. (b7-b4) When read, the content is 0. Figure 12.20 Registers AIER and RMAD0 to RMAD1 Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 117 of 450 After Reset 000000h 000000h Setting Range RW 00000h to FFFFFh RW -- R8C/2K Group, R8C/2L Group 12.5 12. Interrupts Timer RC Interrupt, Timer RD Interrupt (Interrupts with Multiple Interrupt Request Sources) The timer RC interrupt, timer RD (channel 0) interrupt, and timer RD (channel 1) interrupt each have multiple interrupt request sources. An interrupt request is generated by the logical OR of several interrupt request factors and is reflected in the IR bit in the corresponding interrupt control register. Therefore, each of these peripheral functions has its own interrupt request source status register (status register) and interrupt request source enable register (enable register) to control the generation of interrupt requests (change the IR bit in the interrupt control register). Table 12.8 lists the Registers Associated with Timer RC Interrupt and Timer RD Interrupt and Figure 12.21 shows a Block Diagram of Timer RD Interrupt. Table 12.8 Registers Associated with Timer RC Interrupt and Timer RD Interrupt Peripheral Function Name Timer RC Timer RD Channel 0 Channel 1 Status Register of Interrupt Request Source TRCSR TRDSR0 TRDSR1 Enable Register of Interrupt Control Interrupt Request Source Register TRCIER TRCIC TRDIER0 TRD0IC TRDIER1 TRD1IC Channel i IMFA bit IMIEA bit IMFB bit IMIEB bit IMFC bit IMIEC bit IMFD bit IMIED bit UDF bit OVF bit OVIE bit i = 0 or 1 IMFA, IMFB, IMFC, IMFD, OVF, UDF: Bits in TRDSRi register IMIEA, IMIEB, IMIEC, IMIED, OVIE: Bits in TRDIER register Figure 12.21 Block Diagram of Timer RD Interrupt Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 118 of 450 Timer RD (channel i) interrupt request (IR bit in TRDiIC register) R8C/2K Group, R8C/2L Group 12. Interrupts As with other maskable interrupts, the timer RC interrupt, timer RD (channel 0) interrupt, and timer RD (channel 1) interrupt are controlled by the combination of the I flag, IR bit, bits ILVL0 to ILVL2, and IPL. However, since each interrupt source is generated by a combination of multiple interrupt request sources, the following differences from other maskable interrupts apply: * When bits in the enable register corresponding to bits set to 1 in the status register are set to 1 (enable interrupt), the IR bit in the interrupt control register is set to 1 (interrupt requested). * When either bits in the status register or bits in the enable register corresponding to bits in the status register, or both, are set to 0, the IR bit is set to 0 (interrupt not requested). Basically, even though the interrupt is not acknowledged after the IR bit is set to 1, the interrupt request will not be maintained. Also, the IR bit is not set to 0 even if 0 is written to the IR bit. * Individual bits in the status register are not automatically set to 0 even if the interrupt is acknowledged. Therefore, the IR bit is also not automatically set to 0 when the interrupt is acknowledged. Set each bit in the status register to 0 in the interrupt routine. Refer to the status register figure for how to set individual bits in the status register to 0. * When multiple bits in the enable register are set to 1 and other request sources are generated after the IR bit is set to 1, the IR bit remains 1. * When multiple bits in the enable register are set to 1, determine by the status register which request source causes an interrupt. Refer to chapters of the individual peripheral functions (16.3 Timer RC and 16.4 Timer RD) for the status register and enable register. Refer to 12.1.6 Interrupt Control for the interrupt control register. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 119 of 450 R8C/2K Group, R8C/2L Group 12.6 12. Interrupts Notes on Interrupts 12.6.1 Reading Address 00000h Do not read address 00000h by a program. When a maskable interrupt request is acknowledged, the CPU reads interrupt information (interrupt number and interrupt request level) from 00000h in the interrupt sequence. At this time, the acknowledged interrupt IR bit is set to 0. If address 00000h is read by a program, the IR bit for the interrupt which has the highest priority among the enabled interrupts is set to 0. This may cause the interrupt to be canceled, or an unexpected interrupt to be generated. 12.6.2 SP Setting Set any value in the SP before an interrupt is acknowledged. The SP is set to 0000h after reset. Therefore, if an interrupt is acknowledged before setting a value in the SP, the program may run out of control. 12.6.3 External Interrupt and Key Input Interrupt Either "L" level or an "H" level of width shown in the Electrical Characteristics is necessary for the signal input to pins INT0, INT1, INT3 and pins KI0 to KI3, regardless of the CPU clock. For details, refer to Table 22.19 (VCC = 5V), Table 22.25 (VCC = 3V), Table 22.31 (VCC = 2.2V) External Interrupt INTi (i = 0, 1, 3) Input. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 120 of 450 R8C/2K Group, R8C/2L Group 12.6.4 12. Interrupts Changing Interrupt Sources The IR bit in the interrupt control register may be set to 1 (interrupt requested) when the interrupt source changes. When using an interrupt, set the IR bit to 0 (no interrupt requested) after changing the interrupt source. In addition, changes of interrupt sources include all factors that change the interrupt sources assigned to individual software interrupt numbers, polarities, and timing. Therefore, if a mode change of a peripheral function involves interrupt sources, edge polarities, and timing, set the IR bit to 0 (no interrupt requested) after the change. Refer to the individual peripheral function for its related interrupts. Figure 12.22 shows an Example of Procedure for Changing Interrupt Sources. Interrupt source change Disable interrupts(2, 3) Change interrupt source (including mode of peripheral function) Set the IR bit to 0 (interrupt not requested) using the MOV instruction(3) Enable interrupts (2, 3) Change completed IR bit: The interrupt control register bit of an interrupt whose source is changed. NOTES: 1. Execute the above settings individually. Do not execute two or more settings at once (by one instruction). 2. To prevent interrupt requests from being generated disable the peripheral function before changing the interrupt source. In this case, use the I flag if all maskable interrupts can be disabled. If all maskable interrupts cannot be disabled, use bits ILVL0 to ILVL2 of the interrupt whose source is changed. 3. Refer to 12.6.5 Changing Interrupt Control Register Contents for the instructions to be used and usage notes. Figure 12.22 Example of Procedure for Changing Interrupt Sources Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 121 of 450 R8C/2K Group, R8C/2L Group 12.6.5 12. Interrupts Changing Interrupt Control Register Contents (a) The contents of an interrupt control register can only be changed while no interrupt requests corresponding to that register are generated. If interrupt requests may be generated, disable interrupts before changing the interrupt control register contents. (b) When changing the contents of an interrupt control register after disabling interrupts, be careful to choose appropriate instructions. Changing any bit other than IR bit If an interrupt request corresponding to a register is generated while executing the instruction, the IR bit may not be set to 1 (interrupt requested), and the interrupt request may be ignored. If this causes a problem, use the following instructions to change the register: AND, OR, BCLR, BSET Changing IR bit If the IR bit is set to 0 (interrupt not requested), it may not be set to 0 depending on the instruction used. Therefore, use the MOV instruction to set the IR bit to 0. (c) When disabling interrupts using the I flag, set the I flag as shown in the sample programs below. Refer to (b) regarding changing the contents of interrupt control registers by the sample programs. Sample programs 1 to 3 are for preventing the I flag from being set to 1 (interrupts enabled) before the interrupt control register is changed for reasons of the internal bus or the instruction queue buffer. Example 1: Use NOP instructions to prevent I flag from being set to 1 before interrupt control register is changed INT_SWITCH1: FCLR I ; Disable interrupts AND.B #00H,0056H ; Set TRAIC register to 00h NOP ; NOP FSET I ; Enable interrupts Example 2: Use dummy read to delay FSET instruction INT_SWITCH2: FCLR I ; Disable interrupts AND.B #00H,0056H ; Set TRAIC register to 00h MOV.W MEM,R0 ; Dummy read FSET I ; Enable interrupts Example 3: Use POPC instruction to change I flag INT_SWITCH3: PUSHC FLG FCLR I ; Disable interrupts AND.B #00H,0056H ; Set TRAIC register to 00h POPC FLG ; Enable interrupts Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 122 of 450 R8C/2K Group, R8C/2L Group 13. ID Code Areas 13. ID Code Areas 13.1 Overview The ID code areas are used to implement a function that prevents the flash memory from being rewritten in standard serial I/O mode. This function prevents the flash memory from read, rewritten, or erased. The ID code areas are assigned to 0FFDFh, 0FFE3h, 0FFEBh, 0FFEFh, 0FFF3h, 0FFF7h, and 0FFFBh of the respective vector highest-order addresses of the fixed vector table. Figure 13.1 shows the ID Code Areas. ID code areas Address 0FFDFh to 0FFDCh ID1 Undefined instruction vector 0FFE3h to 0FFE0h ID2 Overflow vector BRK instruction vector 0FFE7h to 0FFE4h 0FFEBh to 0FFE8h ID3 Address match vector 0FFEFh to 0FFECh ID4 Single step vector 0FFF3h to 0FFF0h ID5 Oscillation stop detection/watchdog timer/ voltage monitor 1 and voltage monitor 2 0FFF7h to 0FFF4h ID6 Address break vector 0FFFBh to 0FFF8h ID7 0FFFFh to 0FFFCh OFS (Reserved) Reset vector 4 bytes Figure 13.1 13.2 ID Code Areas Functions The ID code areas are used in standard serial I/O mode. Unless 3 bytes (addresses from 0FFFCh to 0FFFEh) of the reset vector are set to FFFFFFh, the ID codes stored in the ID code areas and the ID codes sent from the serial programmer or the on-chip debugging emulator are checked to see if they match. If the ID codes match, the commands sent from the serial programmer or the on-chip debugging emulator are acknowledged. If the ID codes do not match, the commands are not acknowledged. To use the serial programmer or the on-chip debugging simulator, first write predetermined ID codes to the ID code areas. As the ID code areas are allocated in the flash memory (not in the SFRs), they cannot be rewritten by executing an instruction. Write appropriate values when creating a program. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 123 of 450 R8C/2K Group, R8C/2L Group 13.3 13. ID Code Areas Notes on ID Code Areas 13.3.1 Setting Example of ID Code Areas As the ID code areas are allocated in the flash memory (not in the SFRs), they cannot be rewritten by executing an instruction. Write appropriate values when creating a program. The following shows a setting example. * To set 55h in all of the ID code areas .org 00FFDCH .lword dummy | (55000000h) ; UND .lword dummy | (55000000h) ; INTO .lword dummy ; BREAK .lword dummy | (55000000h) ; ADDRESS MATCH .lword dummy | (55000000h) ; SET SINGLE STEP .lword dummy | (55000000h) ; WDT .lword dummy | (55000000h) ; ADDRESS BREAK .lword dummy | (55000000h) ; RESERVE (Programming formats vary depending on the compiler. Check the compiler manual.) Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 124 of 450 R8C/2K Group, R8C/2L Group 14. Option Function Select Area 14. Option Function Select Area 14.1 Overview The option function select area is used to select the MCU state after reset or the function to prevent rewriting in parallel I/O mode. The reset vector highest-order-address, 0FFFFh, is assigned as the option function select area. Figure 14.1 shows the Option Function Select Area. Option function select area Address 0FFFFh to 0FFFCh OFS Reset vector 4 bytes Figure 14.1 Option Function Select Area Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 125 of 450 R8C/2K Group, R8C/2L Group 14.2 14. Option Function Select Area OFS Register The OFS register is used to select the MCU state after reset or the function to prevent rewriting in parallel I/O mode. Figure 14.2 shows the OFS Register. Option Function Select Register(1) b7 b6 b5 b4 b3 b2 b1 b0 1 1 1 Symbol OFS Bit Symbol WDTON -- (b1) ROMCR ROMCP1 -- (b4) LVD0ON -- (b6) Address 0FFFFh Bit Name Watchdog timer start select bit When Shipping FFh(3) Function 0 : Starts w atchdog timer automatically after reset 1 : Watchdog timer is inactive after reset Reserved bit Set to 1. ROM code protect disabled bit 0 : ROM code protect disabled 1 : ROMCP1 enabled RW ROM code protect bit 0 : ROM code protect enabled 1 : ROM code protect disabled RW Reserved bit Set to 1. Voltage detection 0 circuit start bit(2) 0 : Voltage monitor 0 reset enabled after hardw are reset 1 : Voltage monitor 0 reset disabled after hardw are reset Reserved bit Set to 1. Count source protect CSPROINI mode after reset select bit 0 : Count source protect mode enabled after reset 1 : Count source protect mode disabled after reset RW RW RW RW RW RW RW NOTES: 1. The OFS register is on the flash memory. Write to the OFS register w ith a program. After w riting is completed, do not w rite additions to the OFS register. 2. Setting the LVD0ON bit is only valid after a hardw are reset. To use the pow er-on reset, set the LVD0ON bit to 0 (voltage monitor 0 reset enabled after hardw are reset). 3. If the block including the OFS register is erased, FFh is set to the OFS register. Figure 14.2 OFS Register Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 126 of 450 R8C/2K Group, R8C/2L Group 14.3 14. Option Function Select Area Notes on Option Function Select Area 14.3.1 Setting Example of Option Function Select Area As the option function select area is allocated in the flash memory (not in the SFRs), they cannot be rewritten by executing an instruction. Write appropriate values when creating a program. The following shows a setting example. * To set FFh in the OFS register .org 00FFFCH .lword reset | (0FF000000h) ; RESET (Programming formats vary depending on the compiler. Check the compiler manual.) Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 127 of 450 R8C/2K Group, R8C/2L Group 15. Watchdog Timer 15. Watchdog Timer The watchdog timer is a function that detects when a program is out of control. Use of the watchdog timer is recommended to improve the reliability of the system. The watchdog timer contains a 15-bit counter and allows selection of count source protection mode enable or disable. Table 15.1 lists information on the Watchdog Timer Specifications. Refer to 5.6 Watchdog Timer Reset for details on the watchdog timer. Figure 15.1 shows the Block Diagram of Watchdog Timer. Figure 15.2 shows the Registers WDTR, WDTS, and WDC. Figure 15.3 shows the Registers CSPR and OFS. Table 15.1 Watchdog Timer Specifications Item Count source Count Source Protection Mode Disabled CPU clock Count operation Count start condition Count Source Protection Mode Enabled Low-speed on-chip oscillator clock Decrement Either of the following can be selected * After reset, count starts automatically * Count starts by writing to WDTS register Count stop condition Stop mode, wait mode None Reset condition of watchdog * Reset timer * Write 00h to the WDTR register before writing FFh * Underflow Operation at the time of underflow Watchdog timer interrupt or Watchdog timer reset watchdog timer reset Select functions * Division ratio of prescaler Selected by the WDC7 bit in the WDC register * Count source protection mode Whether count source protection mode is enabled or disabled after a reset can be selected by the CSPROINI bit in the OFS register (flash memory). If count source protection mode is disabled after a reset, it can be enabled or disabled by the CSPRO bit in the CSPR register (program). * Starts or stops of the watchdog timer after a reset Selected by the WDTON bit in the OFS register (flash memory). Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 128 of 450 R8C/2K Group, R8C/2L Group 15. Watchdog Timer Prescaler 1/16 CM07 = 0, WDC7 = 0 CSPRO = 0 1/128 CPU clock CM07 = 0, WDC7 = 1 PM12 = 0 Watchdog timer interrupt request Watchdog timer 1/2 CM07 = 1 fOCO-S CSPRO = 1 Write to WDTR register Set to 7FFFh(1) PM12 = 1 Watchdog timer reset Internal reset signal ("L" active) CSPRO: Bit in CSPR register WDC7: Bit in WDC register PM12: Bit in PM1 register CM07: Bit in CM0 register NOTE: 1. When the CSPRO bit is set to 1 (count source protection mode enabled), 0FFFh is set. Figure 15.1 Block Diagram of Watchdog Timer Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 129 of 450 R8C/2K Group, R8C/2L Group 15. Watchdog Timer Watchdog Timer Reset Register b7 b0 Symbol WDTR Address 000Dh After Reset Undefined Function When 00h is w ritten before w riting FFh, the w atchdog timer is reset.(1) The default value of the w atchdog timer is 7FFFh w hen count source protection mode is disabled and 0FFFh w hen count source protection mode is enabled.(2) RW WO NOTES: 1. Do not generate an interrupt betw een w hen 00h and FFh are w ritten. 2. When the CSPRO bit in the CSPR register is set to 1 (count source protection mode enabled), 0FFFh is set in the w atchdog timer. Watchdog Timer Start Register b7 b0 Symbol WDTS Address 000Eh After Reset Undefined Function The w atchdog timer starts counting after a w rite instruction to this register. RW WO Watchdog Timer Control Register b7 b6 b5 b4 b3 b2 b1 b0 0 0 Symbol Address 000Fh WDC Bit Symbol Bit Name -- High-order bits of w atchdog timer (b4-b0) -- (b5) Reserved bit Set to 0. When read, the content is undefined. -- (b6) Reserved bit Set to 0. Prescaler select bit 0 : Divide-by-16 1 : Divide-by-128 WDC7 Figure 15.2 Registers WDTR, WDTS, and WDC Rev.1.10 Dec 21, 2007 REJ09B0406-0110 After Reset 00X11111b Function Page 130 of 450 RW RO RW RW RW R8C/2K Group, R8C/2L Group 15. Watchdog Timer Count Source Protection Mode Register b7 b6 b5 b4 b3 b2 b1 b0 0 0 0 0 0 0 0 Symbol Address 001Ch CSPR Bit Symbol Bit Name -- Reserved bits (b6-b0) CSPRO After Reset(1) 00h Function Set to 0. Count source protection mode 0 : Count source protection mode disabled 1 : Count source protection mode enabled select bit(2) RW RW RW NOTES: 1. When 0 is w ritten to the CSPROINI bit in the OFS register, the value after reset is 10000000b. 2. Write 0 before w riting 1 to set the CSPRO bit to 1. 0 cannot be set by a program. Option Function Select Register(1) b7 b6 b5 b4 b3 b2 b1 b0 1 1 1 Symbol OFS Bit Symbol WDTON -- (b1) ROMCR ROMCP1 -- (b4) LVD0ON -- (b6) Address 0FFFFh Bit Name Watchdog timer start select bit When Shipping FFh(3) Function 0 : Starts w atchdog timer automatically after reset 1 : Watchdog timer is inactive after reset Reserved bit Set to 1. ROM code protect disabled bit 0 : ROM code protect disabled 1 : ROMCP1 enabled RW ROM code protect bit 0 : ROM code protect enabled 1 : ROM code protect disabled RW Reserved bit Set to 1. Voltage detection 0 circuit start bit(2) 0 : Voltage monitor 0 reset enabled after hardw are reset 1 : Voltage monitor 0 reset disabled after hardw are reset Reserved bit Set to 1. Count source protect CSPROINI mode after reset select bit 0 : Count source protect mode enabled after reset 1 : Count source protect mode disabled after reset RW RW RW RW RW RW RW NOTES: 1. The OFS register is on the flash memory. Write to the OFS register w ith a program. After w riting is completed, do not w rite additions to the OFS register. 2. Setting the LVD0ON bit is only valid after a hardw are reset. To use the pow er-on reset, set the LVD0ON bit to 0 (voltage monitor 0 reset enabled after hardw are reset). 3. If the block including the OFS register is erased, FFh is set to the OFS register. Figure 15.3 Registers CSPR and OFS Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 131 of 450 R8C/2K Group, R8C/2L Group 15.1 15. Watchdog Timer Count Source Protection Mode Disabled The count source of the watchdog timer is the CPU clock when count source protection mode is disabled. Table 15.2 lists the Watchdog Timer Specifications (with Count Source Protection Mode Disabled). Table 15.2 Watchdog Timer Specifications (with Count Source Protection Mode Disabled) Item Specification Count source Count operation Period CPU clock Decrement Reset condition of watchdog timer Count start condition Count stop condition Operation at time of underflow Division ratio of prescaler (n) x count value of watchdog timer (32768)(1) CPU clock n: 16 or 128 (selected by WDC7 bit in WDC register) Example: When the CPU clock frequency is 16 MHz and prescaler divided by 16, the period is approximately 32.8 ms * Reset * Write 00h to the WDTR register before writing FFh * Underflow The WDTON bit(2) in the OFS register (0FFFFh) selects the operation of the watchdog timer after a reset * When the WDTON bit is set to 1 (watchdog timer is in stop state after reset) The watchdog timer and prescaler stop after a reset and the count starts when the WDTS register is written to * When the WDTON bit is set to 0 (watchdog timer starts automatically after exiting) The watchdog timer and prescaler start counting automatically after a reset Stop and wait modes (inherit the count from the held value after exiting modes) * When the PM12 bit in the PM1 register is set to 0 Watchdog timer interrupt * When the PM12 bit in the PM1 register is set to 1 Watchdog timer reset (Refer to 5.6 Watchdog Timer Reset.) NOTES: 1. The watchdog timer is reset when 00h is written to the WDTR register before FFh. The prescaler is reset after the MCU is reset. Some errors in the period of the watchdog timer may be caused by the prescaler. 2. The WDTON bit cannot be changed by a program. To set the WDTON bit, write 0 to bit 0 of address 0FFFFh with a flash programmer. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 132 of 450 R8C/2K Group, R8C/2L Group 15.2 15. Watchdog Timer Count Source Protection Mode Enabled The count source of the watchdog timer is the low-speed on-chip oscillator clock when count source protection mode is enabled. If the CPU clock stops when a program is out of control, the clock can still be supplied to the watchdog timer. Table 15.3 lists the Watchdog Timer Specifications (with Count Source Protection Mode Enabled). Table 15.3 Watchdog Timer Specifications (with Count Source Protection Mode Enabled) Item Count source Count operation Period Reset condition of watchdog timer Count start condition Count stop condition Operation at time of underflow Registers, bits Specification Low-speed on-chip oscillator clock Decrement Count value of watchdog timer (4096) Low-speed on-chip oscillator clock Example: Period is approximately 32.8 ms when the low-speed onchip oscillator clock frequency is 125 kHz * Reset * Write 00h to the WDTR register before writing FFh * Underflow The WDTON bit(1) in the OFS register (0FFFFh) selects the operation of the watchdog timer after a reset. * When the WDTON bit is set to 1 (watchdog timer is in stop state after reset) The watchdog timer and prescaler stop after a reset and the count starts when the WDTS register is written to * When the WDTON bit is set to 0 (watchdog timer starts automatically after reset) The watchdog timer and prescaler start counting automatically after a reset None (The count does not stop in wait mode after the count starts. The MCU does not enter stop mode.) Watchdog timer reset (Refer to 5.6 Watchdog Timer Reset.) * When setting the CSPPRO bit in the CSPR register to 1 (count source protection mode is enabled)(2), the following are set automatically - Set 0FFFh to the watchdog timer - Set the CM14 bit in the CM1 register to 0 (low-speed on-chip oscillator on) - Set the PM12 bit in the PM1 register to 1 (The watchdog timer is reset when watchdog timer underflows) * The following conditions apply in count source protection mode - Writing to the CM10 bit in the CM1 register is disabled (It remains unchanged even if it is set to 1. The MCU does not enter stop mode.) - Writing to the CM14 bit in the CM1 register is disabled (It remains unchanged even if it is set to 1. The low-speed on-chip oscillator does not stop.) NOTES: 1. The WDTON bit cannot be changed by a program. To set the WDTON bit, write 0 to bit 0 of address 0FFFFh with a flash programmer. 2. Even if 0 is written to the CSPROINI bit in the OFS register, the CSPRO bit is set to 1. The CSPROINI bit cannot be changed by a program. To set the CSPROINI bit, write 0 to bit 7 of address 0FFFFh with a flash programmer. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 133 of 450 R8C/2K Group, R8C/2L Group 16. Timers 16. Timers The MCU has two 8-bit timers with 8-bit prescalers and two 16-bit timers. The two 8-bit timers with 8-bit prescalers are timer RA and timer RB. These timers contain a reload register to store the default value of the counter. The two 16bit timers are timer RC, timer RD, and have input capture and output compare functions. All the timers operate independently. Tables 16.1 lists Functional Comparison of Timers. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 134 of 450 R8C/2K Group, R8C/2L Group Table 16.1 16. Timers Functional Comparison of Timers Item Configuration Count Count sources Function Count of the internal count source Count of the external count source External pulse width/ period measurement Timer RA 8-bit timer with 8-bit prescaler (with reload register) Decrement * f1 * f2 * f8 * fOCO Timer RB 8-bit timer with 8-bit prescaler (with reload register) Decrement * f1 * f2 * f8 * Timer RA underflow Timer mode Timer mode Event counter mode -- Pulse width measurement mode, pulse period measurement mode -- Timer RC 16-bit timer (with input capture and output compare) Increment * f1 * f2 * f4 * f8 * f32 * fOCO40M * TRCCLK Timer mode (output compare function) Timer mode (output compare function) Timer mode (input capture function; 4 pins) Timer RD 16-bit timer x 2 (with input capture and output compare) Increment/Decrement * f1 * f2 * f4 * f8 * f32 * fOCO40M * TRDIOA0 Timer mode (output compare function) Timer mode (output compare function) Timer mode (input compare function; 2 channels x 4 pins) Timer mode (output compare function; 2 channels x 4 pins)(1), PWM mode (2 channels x 3 pins), PWM3 mode (2 channels x 2 pins) PWM mode (2 channels x 3 pins) PWM output Pulse output mode(1), Programmable Event counter mode(1) waveform generation mode Timer mode (output compare function; 4 pins)(1), PWM mode (3 pins), PWM2 mode (1 pin) One-shot waveform output -- PWM mode (3 pins) Three-phase waveforms output -- Programmable oneshot generation mode, Programmable wait one-shot generation mode -- -- Reset synchronous PWM mode (2 channels x 3 pins, Sawtooth wave modulation), Complementary PWM mode (2 channels x 3 pins, triangular wave modulation, dead time) Input pin TRAIO INT0 INT0, TRCCLK, TRCTRG, TRCIOA, TRCIOB, TRCIOC, TRCIOD Output pin TRAO TRAIO TRBO TRCIOA, TRCIOB, TRCIOC, TRCIOD Related interrupt Timer RA interrupt, INT1 interrupt Timer RB interrupt, INT0 interrupt Compare match/input capture A to D interrupt, Overflow interrupt, INT0 interrupt Timer stop Provided Provided Provided INT0, TRDCLK, TRDIOA0, TRDIOA1, TRDIOB0, TRDIOB1, TRDIOC0, TRDIOC1, TRDIOD0, TRDIOD1 TRDIOA0, TRDIOA1, TRDIOB0, TRDIOB1, TRDIOC0, TRDIOC1, TRDIOD0, TRDIOD1 Compare match/input capture A0 to D0 interrupt, Compare match/input capture A1 to D1 interrupt, Overflow interrupt, Underflow interrupt(2), INT0 interrupt Provided NOTES: 1. Rectangular waves are output in these modes. Since the waves are inverted at each overflow, the "H" and "L" level widths of the pulses are the same. 2. The underflow interrupt can be set to channel 1. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 135 of 450 R8C/2K Group, R8C/2L Group 16.1 16. Timers Timer RA Timer RA is an 8-bit timer with an 8-bit prescaler. The prescaler and timer each consist of a reload register and counter. The reload register and counter are allocated at the same address, and can be accessed when accessing registers TRAPRE and TRA (refer to Tables 16.2 to 16.6 the Specification of Each Modes). The count source for timer RA is the operating clock that regulates the timing of timer operations such as counting and reloading. Figure 16.1 shows a Block Diagram of Timer RA. Figures 16.2 and 16.3 show the registers associated with Timer RA. Timer RA contains the following five operating modes: * Timer mode: The timer counts the internal count source. * Pulse output mode: The timer counts the internal count source and outputs pulses which invert the polarity by underflow of the timer. * Event counter mode: The timer counts external pulses. * Pulse width measurement mode: The timer measures the pulse width of an external pulse. * Pulse period measurement mode: The timer measures the pulse period of an external pulse. Data bus TCK2 to TCK0 bit = 000b f1 = 001b f8 = 010b fOCO = 011b f2 TCKCUT bit TMOD2 to TMOD0 = other than 010b TIPF1 to TIPF0 bits TMOD2 to TMOD0 = 010b Reload register Reload register TCSTF bit Counter TRAPRE register (prescaler) Counter TRA register (timer) Underflow signal Timer RA interrupt = 01b f1 = 10b f8 = 11b f32 TIPF1 to TIPF0 bits TIOSEL = 0 = other than Digital 000b INT1/TRAIO (P1_7) pin filter INT1/TRAIO (P1_5) pin TIOSEL = 1 TMOD2 to TMOD0 = 011b or 100b Polarity switching Count control circle = 00b TMOD2 to TMOD0 = 001b TEDGSEL = 1 TOPCR bit Q Q TEDGSEL = 0 Measurement completion signal Toggle flip-flop CK CLR Write to TRAMR register Write 1 to TSTOP bit TCSTF, TSTOP: TRACR register TEDGSEL, TOPCR, TIOSEL, TIPF1, TIPF0: TRAIOC register TMOD2 to TMOD0, TCK2 to TCK0, TCKCUT: TRAMR register Figure 16.1 Block Diagram of Timer RA Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 136 of 450 R8C/2K Group, R8C/2L Group 16. Timers Timer RA Control Register(4) b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRACR Bit Symbol Address 0100h Bit Name Timer RA count start bit(1) After Reset 00h Function RW 0 : Count stops 1 : Count starts RW TCSTF Timer RA count status flag(1) 0 : Count stops 1 : During count RO TSTOP Timer RA count forcible stop When this bit is set to 1, the count is forcibly bit(2) stopped. When read, its content is 0. RW TSTART -- (b3) TEDGF Nothing is assigned. If necessary, set to 0. When read, the content is 0. Active edge judgment flag(3, 5) 0 : Active edge not received 1 : Active edge received (end of measurement period) -- RW TUNDF Timer RA underflow flag(3, 5) 0 : No underflow 1 : Underflow RW -- (b7-b6) Nothing is assigned. If necessary, set to 0. When read, the content is 0. -- NOTES: 1. Refer to 16.1.6 Notes on Tim er RA for precautions regarding bits TSTART and TCSTF. 2. When the TSTOP bit is set to 1, bits TSTART and TCSTF and registers TPRAPRE and TRA are set to the values after a reset. 3. Bits TEDGF and TUNDF can be set to 0 by w riting 0 to these bits by a program. How ever, their value remains unchanged w hen 1 is w ritten. 4. In pulse w idth measurement mode and pulse period measurement mode, use the MOV instruction to set the TRACR register. If it is necessary to avoid changing the values of bits TEDGF and TUNDF, w rite 1 to them. 5. Set to 0 in timer mode, pulse output mode, and event counter mode. Timer RA I/O Control Register b7 b6 b5 b4 b3 b2 b1 b0 0 Symbol TRAIOC Bit Symbol TEDGSEL TOPCR -- (b2) Address 0101h Bit Name TRAIO polarity sw itch bit TRAIO output control bit Reserved bit _____ TIOSEL TIPF0 TIPF1 -- (b7-b6) Figure 16.2 INT1/TRAIO select bit Set to 0. Function varies depending on operating mode. Nothing is assigned. If necessary, set to 0. When read, the content is 0. Page 137 of 450 RW RW RW TRAIO input filter select bits Registers TRACR and TRAIOC Rev.1.10 Dec 21, 2007 REJ09B0406-0110 After Reset 00h Function Function varies depending on operating mode. RW RW RW -- R8C/2K Group, R8C/2L Group 16. Timers Timer RA Mode Register b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRAMR Bit Symbol TMOD0 Address 0102h Bit Name Timer RA operating mode select bits (1) TMOD1 TMOD2 After Reset 00h Function 0 0 0 : Timer mode 0 0 1 : Pulse output mode 0 1 0 : Event counter mode 0 1 1 : Pulse w idth measurement mode 1 0 0 : Pulse period measurement mode 101: 1 1 0 : Do not set. 111: -- (b3) Nothing is assigned. If necessary, set to 0. When read, the content is 0. TCK0 Timer RA count source select bits TCK1 TCK2 TCKCUT Timer RA count source cutoff bit RW b2 b1 b0 RW RW RW -- b6 b5 b4 0 0 0 : f1 0 0 1 : f8 0 1 0 : fOCO 0 1 1 : f2 100: 1 0 1 : Do not set. 110: 111: RW 0 : Provides count source 1 : Cuts off count source RW RW RW NOTE: 1. When both the TSTART and TCSTF bits in the TRACR register are set to 0 (count stops), rew rite this register. Timer RA Prescaler Register b7 b0 Symbol TRAPRE Mode Timer mode Pulse output mode Event counter mode Pulse w idth measurement mode Address 0103h Function Counts an internal count source Pulse period measurement mode Measure pulse period of input pulses from external (counts internal count source) Counts an external count source Measure pulse w idth of input pulses from external (counts internal count source) After Reset FFh(1) Setting Range 00h to FFh 00h to FFh 00h to FFh RW RW RW RW 00h to FFh RW 00h to FFh RW After Reset FFh(1) Setting Range RW 00h to FFh RW NOTE: 1. When the TSTOP bit in the TRACR register is set to 1, the TRAPRE register is set to FFh. Timer RA Register b7 b0 Symbol TRA Mode All modes Address 0104h Function Counts on underflow of timer RA prescaler register NOTE: 1. When the TSTOP bit in the TRACR register is set to 1, the TRA register is set to FFh. Figure 16.3 Registers TRAMR, TRAPRE, and TRA Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 138 of 450 R8C/2K Group, R8C/2L Group 16.1.1 16. Timers Timer Mode In this mode, the timer counts an internally generated count source (refer to Table 16.2 Timer Mode Specifications). Figure 16.4 shows the TRAIOC Register in Timer Mode. Table 16.2 Timer Mode Specifications Item Count sources Count operations Divide ratio Count start condition Count stop conditions Interrupt request generation timing INT1/TRAIO pin function Read from timer Write to timer Specification f1, f2, f8, fOCO * Decrement * When the timer underflows, the contents of the reload register are reloaded and the count is continued. 1/(n+1)(m+1) n: Value set in TRAPRE register, m: Value set in TRA register 1 (count starts) is written to the TSTART bit in the TRACR register. * 0 (count stops) is written to the TSTART bit in the TRACR register. * 1 (count forcibly stops) is written to the TSTOP bit in the TRACR register. When timer RA underflows [timer RA interrupt]. Programmable I/O port, or INT1 interrupt input The count value can be read by reading registers TRA and TRAPRE. * When registers TRAPRE and TRA are written while the count is stopped, values are written to both the reload register and counter. * When registers TRAPRE and TRA are written during the count, values are written to the reload register and counter. (Refer to 16.1.1.1 Timer Write Control during Count Operation.) Timer RA I/O Control Register b7 b6 b5 b4 b3 b2 b1 b0 0 0 0 0 0 Symbol TRAIOC Bit Symbol TEDGSEL TOPCR -- (b2) Address 0101h Bit Name TRAIO polarity sw itch bit TRAIO output control bit Reserved bit _____ TIOSEL TIPF0 TIPF1 -- (b7-b6) Figure 16.4 Set to 0. RW RW _____ 0 : INT1/TRAIO pin (P1_7) _____ 1 : INT1/TRAIO pin (P1_5) TRAIO input filter select bits Set to 0 in timer mode. Nothing is assigned. If necessary, set to 0. When read, the content is 0. Page 139 of 450 RW RW INT1/TRAIO select bit TRAIOC Register in Timer Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 After Reset 00h Function Set to 0 in timer mode. RW RW -- R8C/2K Group, R8C/2L Group 16.1.1.1 16. Timers Timer Write Control during Count Operation Timer RA has a prescaler and a timer (which counts the prescaler underflows). The prescaler and timer each consist of a reload register and a counter. When writing to the prescaler or timer, values are written to both the reload register and counter. However, values are transferred from the reload register to the counter of the prescaler in synchronization with the count source. In addition, values are transferred from the reload register to the counter of the timer in synchronization with prescaler underflows. Therefore, if the prescaler or timer is written to when count operation is in progress, the counter value is not updated immediately after the WRITE instruction is executed. Figure 16.5 shows an Operating Example of Timer RA when Counter Value is Rewritten during Count Operation. Set 01h to the TRAPRE register and 25h to the TRA register by a program. Count source After writing, the reload register is written to at the first count source. Reloads register of timer RA prescaler Previous value New value (01h) Reload at second count source Counter of timer RA prescaler 06h 05h 04h 01h 00h Reload at underflow 01h 00h 01h 00h 01h 00h After writing, the reload register is written to at the first underflow. Reloads register of timer RA Previous value New value (25h) Reload at the second underflow Counter of timer RA IR bit in TRAIC register 03h 02h 25h 24h 0 The IR bit remains unchanged until underflow is generated by a new value. The above applies under the following conditions. Both bits TSTART and TCSTF in the TRACR register are set to 1 (During count). Figure 16.5 Operating Example of Timer RA when Counter Value is Rewritten during Count Operation Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 140 of 450 R8C/2K Group, R8C/2L Group 16.1.2 16. Timers Pulse Output Mode In pulse output mode, the internally generated count source is counted, and a pulse with inverted polarity is output from the TRAIO pin each time the timer underflows (refer to Table 16.3 Pulse Output Mode Specifications). Figure 16.6 shows the TRAIOC Register in Pulse Output Mode. Table 16.3 Pulse Output Mode Specifications Item Count sources Count operations Specification f1, f2, f8, fOCO * Decrement * When the timer underflows, the contents in the reload register is reloaded and the count is continued. Divide ratio 1/(n+1)(m+1) n: Value set in TRAPRE register, m: Value set in TRA register Count start condition 1 (count starts) is written to the TSTART bit in the TRACR register. Count stop conditions * 0 (count stops) is written to the TSTART bit in the TRACR register. * 1 (count forcibly stops) is written to the TSTOP bit in the TRACR register. Interrupt request When timer RA underflows [timer RA interrupt]. generation timing INT1/TRAIO pin function Pulse output, programmable output port, or INT1 interrupt(1) Read from timer Write to timer The count value can be read by reading registers TRA and TRAPRE. Select functions * TRAIO signal polarity switch function The TEDGSEL bit in the TRAIOC register selects the level at the start of pulse output.(1) * Pulse output stop function Output from the TRAIO pin is stopped by the TOPCR bit in the TRAIOC register. * INT1/TRAIO pin select function P1_7 or P1_5 is selected by the TIOSEL bit in the TRAIOC register. * When registers TRAPRE and TRA are written while the count is stopped, values are written to both the reload register and counter. * When registers TRAPRE and TRA are written during the count, values are written to the reload register and counter. (Refer to 16.1.1.1 Timer Write Control during Count Operation.) NOTE: 1. The level of the output pulse becomes the level when the pulse output starts when the TRAMR register is written to. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 141 of 450 R8C/2K Group, R8C/2L Group 16. Timers Timer RA I/O Control Register b7 b6 b5 b4 b3 b2 b1 b0 0 0 0 Symbol TRAIOC Bit Symbol TEDGSEL TOPCR -- (b2) Address 0101h Bit Name TRAIO polarity sw itch bit After Reset 00h Function 0 : TRAIO output starts at "H" 1 : TRAIO output starts at "L" RW TRAIO output control bit 0 : TRAIO output 1 : Port P1_7 or P1_5 RW Reserved bit Set to 0. _____ TIOSEL TIPF0 TIPF1 -- (b7-b6) Figure 16.6 Rev.1.10 Dec 21, 2007 REJ09B0406-0110 0 : INT1/TRAIO pin (P1_7) _____ 1 : INT1/TRAIO pin (P1_5) TRAIO input filter select bits Set to 0 in pulse output mode. Nothing is assigned. If necessary, set to 0. When read, the content is 0. Page 142 of 450 RW _____ INT1/TRAIO select bit TRAIOC Register in Pulse Output Mode RW RW RW RW -- R8C/2K Group, R8C/2L Group 16.1.3 16. Timers Event Counter Mode In event counter mode, external signal inputs to the INT1/TRAIO pin are counted (refer to Table 16.4 Event Counter Mode Specifications). Figure 16.7 shows the TRAIOC Register in Event Counter Mode. Table 16.4 Event Counter Mode Specifications Item Count source Count operations Specification External signal which is input to TRAIO pin (active edge selectable by a program) * Decrement * When the timer underflows, the contents of the reload register are reloaded and the count is continued. Divide ratio 1/(n+1)(m+1) n: setting value of TRAPRE register, m: setting value of TRA register Count start condition 1 (count starts) is written to the TSTART bit in the TRACR register. Count stop conditions * 0 (count stops) is written to the TSTART bit in the TRACR register. * 1 (count forcibly stops) is written to the TSTOP bit in the TRACR register. Interrupt request * When timer RA underflows [timer RA interrupt]. generation timing INT1/TRAIO pin function Read from timer Write to timer Count source input (INT1 interrupt input) Select functions * INT1 input polarity switch function The TEDGSEL bit in the TRAIOC register selects the active edge of the count source. * Count source input pin select function P1_7 or P1_5 is selected by the TIOSEL bit in the TRAIOC register. * Digital filter function Bits TIPF0 and TIPF1 in the TRAIOC register enable or disable the digital filter and select the sampling frequency. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 The count value can be read by reading registers TRA and TRAPRE. * When registers TRAPRE and TRA are written while the count is stopped, values are written to both the reload register and counter. * When registers TRAPRE and TRA are written during the count, values are written to the reload register and counter. (Refer to 16.1.1.1 Timer Write Control during Count Operation.) Page 143 of 450 R8C/2K Group, R8C/2L Group 16. Timers Timer RA I/O Control Register b7 b6 b5 b4 b3 b2 b1 b0 0 0 Symbol TRAIOC Bit Symbol Address 0101h Bit Name TRAIO polarity sw itch bit TEDGSEL TOPCR -- (b2) TRAIO output control bit Set to 0 in event counter mode. Reserved bit Set to 0. _____ TIOSEL TIPF0 0 : INT1/TRAIO pin (P1_7) _____ 1 : INT1/TRAIO pin (P1_5) TRAIO input filter select bits (1) b5 b4 0 0 : No filter 0 1 : Filter w ith f1 sampling 1 0 : Filter w ith f8 sampling 1 1 : Filter w ith f32 sampling Nothing is assigned. If necessary, set to 0. When read, the content is 0. NOTE: 1. When the same value from the TRAIO pin is sampled three times continuously, the input is determined. Figure 16.7 TRAIOC Register in Event Counter Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 144 of 450 RW RW RW RW _____ INT1/TRAIO select bit TIPF1 -- (b7-b6) After Reset 00h Function 0 : Starts counting at rising edge of the TRAIO input or TRAIO starts output at "L" 1 : Starts counting at falling edge of the TRAIO input or TRAIO starts output at "H" RW RW -- R8C/2K Group, R8C/2L Group 16.1.4 16. Timers Pulse Width Measurement Mode In pulse width measurement mode, the pulse width of an external signal input to the INT1/TRAIO pin is measured (refer to Table 16.5 Pulse Width Measurement Mode Specifications). Figure 16.8 shows the TRAIOC Register in Pulse Width Measurement Mode and Figure 16.9 shows an Operating Example of Pulse Width Measurement Mode. Table 16.5 Pulse Width Measurement Mode Specifications Item Count sources Count operations Count start condition Count stop conditions Interrupt request generation timing Specification f1, f2, f8, fOCO * Decrement * Continuously counts the selected signal only when measurement pulse is "H" level, or conversely only "L" level. * When the timer underflows, the contents of the reload register are reloaded and the count is continued. 1 (count starts) is written to the TSTART bit in the TRACR register. * 0 (count stops) is written to the TSTART bit in the TRACR register. * 1 (count forcibly stops) is written to the TSTOP bit in the TRACR register. * When timer RA underflows [timer RA interrupt]. * Rising or falling of the TRAIO input (end of measurement period) [timer RA interrupt] INT1/TRAIO pin function Measured pulse input (INT1 interrupt input) Read from timer Write to timer The count value can be read by reading registers TRA and TRAPRE. * When registers TRAPRE and TRA are written while the count is stopped, values are written to both the reload register and counter. * When registers TRAPRE and TRA are written during the count, values are written to the reload register and counter. (Refer to 16.1.1.1 Timer Write Control during Count Operation.) Select functions * Measurement level select The TEDGSEL bit in the TRAIOC register selects the "H" or "L" level period. * Measured pulse input pin select function P1_7 or P1_5 is selected by the TIOSEL bit in the TRAIOC register. * Digital filter function Bits TIPF0 and TIPF1 in the TRAIOC register enable or disable the digital filter and select the sampling frequency. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 145 of 450 R8C/2K Group, R8C/2L Group 16. Timers Timer RA I/O Control Register b7 b6 b5 b4 b3 b2 b1 b0 0 0 Symbol TRAIOC Bit Symbol TEDGSEL TOPCR -- (b2) Address 0101h Bit Name TRAIO polarity sw itch bit After Reset 00h Function 0 : TRAIO input starts at "L" 1 : TRAIO input starts at "H" TRAIO output control bit Set to 0 in pulse w idth measurement mode. Reserved bit Set to 0. _____ TIOSEL TIPF0 -- (b7-b6) 0 : INT1/TRAIO pin (P1_7) _____ 1 : INT1/TRAIO pin (P1_5) TRAIO input filter select bits (1) b5 b4 0 0 : No filter 0 1 : Filter w ith f1 sampling 1 0 : Filter w ith f8 sampling 1 1 : Filter w ith f32 sampling Nothing is assigned. If necessary, set to 0. When read, the content is 0. NOTE: 1. When the same value from the TRAIO pin is sampled three times continuously, the input is determined. Figure 16.8 TRAIOC Register in Pulse Width Measurement Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 146 of 450 RW RW RW _____ INT1/TRAIO select bit TIPF1 RW RW RW -- R8C/2K Group, R8C/2L Group 16. Timers n = high level: the contents of TRA register, low level: the contents of TRAPRE register FFFFh Count start Underflow Content of counter (hex) n Count stop Count stop Count start 0000h Count start Period Set to 1 by program TSTART bit in TRACR register 1 Measured pulse (TRAIO pin input) 1 0 0 Set to 0 when interrupt request is acknowledged, or set by program IR bit in TRAIC register 1 0 Set to 0 by program TEDGF bit in TRACR register 1 0 Set to 0 by program TUNDF bit in TRACR register 1 0 The above applies under the following conditions. * "H" level width of measured pulse is measured. (TEDGSEL = 1) * TRAPRE = FFh Figure 16.9 Operating Example of Pulse Width Measurement Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 147 of 450 R8C/2K Group, R8C/2L Group 16.1.5 16. Timers Pulse Period Measurement Mode In pulse period measurement mode, the pulse period of an external signal input to the INT1/TRAIO pin is measured (refer to Table 16.6 Pulse Period Measurement Mode Specifications). Figure 16.10 shows the TRAIOC Register in Pulse Period Measurement Mode and Figure 16.11 shows an Operating Example of Pulse Period Measurement Mode. Table 16.6 Pulse Period Measurement Mode Specifications Item Count sources Count operations Count start condition Count stop conditions Interrupt request generation timing Specification f1, f2, f8, fOCO * Decrement * After the active edge of the measured pulse is input, the contents of the readout buffer are retained at the first underflow of timer RA prescaler. Then timer RA reloads the contents in the reload register at the second underflow of timer RA prescaler and continues counting. 1 (count start) is written to the TSTART bit in the TRACR register. * 0 (count stop) is written to TSTART bit in the TRACR register. * 1 (count forcibly stops) is written to the TSTOP bit in the TRACR register. * When timer RA underflows or reloads [timer RA interrupt]. * Rising or falling of the TRAIO input (end of measurement period) [timer RA interrupt] INT1/TRAIO pin function Measured pulse input(1) (INT1 interrupt input) Read from timer The count value can be read by reading registers TRA and TRAPRE. Write to timer * When registers TRAPRE and TRA are written while the count is stopped, values are written to both the reload register and counter. * When registers TRAPRE and TRA are written during the count, values are written to the reload register and counter. (Refer to 16.1.1.1 Timer Write Control during Count Operation.) Select functions * Measurement period select The TEDGSEL bit in the TRAIOC register selects the measurement period of the input pulse. * Measured pulse input pin select function P1_7 or P1_5 is selected by the TIOSEL bit in the TRAIOC register. * Digital filter function Bits TIPF0 and TIPF1 in the TRAIOC register enable or disable the digital filter and select the sampling frequency. NOTE: 1. Input a pulse with a period longer than twice the timer RA prescaler period. Input a pulse with a longer "H" and "L" width than the timer RA prescaler period. If a pulse with a shorter period is input to the TRAIO pin, the input may be ignored. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 148 of 450 R8C/2K Group, R8C/2L Group 16. Timers Timer RA I/O Control Register b7 b6 b5 b4 b3 b2 b1 b0 0 0 Symbol TRAIOC Bit Symbol Address 0101h Bit Name TRAIO polarity sw itch bit TEDGSEL TOPCR -- (b2) TRAIO output control bit Set to 0 in pulse period measurement mode. Reserved bit Set to 0. _____ TIOSEL TIPF0 0 : INT1/TRAIO pin (P1_7) _____ 1 : INT1/TRAIO pin (P1_5) TRAIO input filter select bits (1) b5 b4 0 0 : No filter 0 1 : Filter w ith f1 sampling 1 0 : Filter w ith f8 sampling 1 1 : Filter w ith f32 sampling Nothing is assigned. If necessary, set to 0. When read, the content is 0. NOTE: 1. When the same value from the TRAIO pin is sampled three times continuously, the input is determined. Figure 16.10 TRAIOC Register in Pulse Period Measurement Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 149 of 450 RW RW RW RW _____ INT1/TRAIO select bit TIPF1 -- (b7-b6) After Reset 00h Function 0 : Measures measurement pulse from one rising edge to next rising edge 1 : Measures measurement pulse from one falling edge to next falling edge RW RW -- R8C/2K Group, R8C/2L Group 16. Timers Underflow signal of timer RA prescaler Set to 1 by program TSTART bit in TRACR register 1 0 Starts counting Measurement pulse (TRAIO pin input) 1 0 TRA reloads TRA reloads 0Fh 0Eh 0Dh 0Fh 0Eh 0Dh 0Ch 0Bh 0Ah 09h 0Fh 0Eh 0Dh Contents of TRA 01h 00h 0Fh 0Eh Underflow Retained Contents of read-out buffer(1) 0Fh Retained 0Dh 0Eh 0Bh 0Ah 09h 0Dh 01h 00h 0Fh 0Eh TRA read(3) (Note 2) TEDGF bit in TRACR register (Note 2) 1 0 Set to 0 by program (Note 4) (Note 6) TUNDF bit in TRACR register 1 0 Set to 0 by program IR bit in TRAIC register (Note 5) 1 0 Set to 0 when interrupt request is acknowledged, or set by program Conditions: The period from one rising edge to the next rising edge of the measured pulse is measured (TEDGSEL = 0) with the default value of the TRA register as 0Fh. NOTES: 1. The contents of the read-out buffer can be read by reading the TRA register in pulse period measurement mode. 2. After an active edge of the measured pulse is input, the TEDGF bit in the TRACR register is set to 1 (active edge found) when the timer RA prescaler underflows for the second time. 3. The TRA register should be read before the next active edge is input after the TEDGF bit is set to 1 (active edge found). The contents in the read-out buffer are retained until the TRA register is read. If the TRA register is not read before the next active edge is input, the measured result of the previous period is retained. 4. To set to 0 by a program, use a MOV instruction to write 0 to the TEDGF bit in the TRACR register. At the same time, write 1 to the TUNDF bit in the TRACR register. 5. To set to 0 by a program, use a MOV instruction to write 0 to the TUNDF bit. At the same time, write 1 to the TEDGF bit. 6. Bits TUNDF and TEDGF are both set to 1 if timer RA underflows and reloads on an active edge simultaneously. Figure 16.11 Operating Example of Pulse Period Measurement Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 150 of 450 R8C/2K Group, R8C/2L Group 16.1.6 16. Timers Notes on Timer RA * Timer RA stops counting after a reset. Set the values in the timer RA and timer RA prescalers before the count starts. * Even if the prescaler and timer RA are read out in 16-bit units, these registers are read 1 byte at a time by the MCU. Consequently, the timer value may be updated during the period when these two registers are being read. * In pulse period measurement mode, bits TEDGF and TUNDF in the TRACR register can be set to 0 by writing 0 to these bits by a program. However, these bits remain unchanged if 1 is written. When using the READ-MODIFY-WRITE instruction for the TRACR register, the TEDGF or TUNDF bit may be set to 0 although these bits are set to 1 while the instruction is being executed. In this case, write 1 to the TEDGF or TUNDF bit which is not supposed to be set to 0 with the MOV instruction. * When changing to pulse period measurement mode from another mode, the contents of bits TEDGF and TUNDF are undefined. Write 0 to bits TEDGF and TUNDF before the count starts. * The TEDGF bit may be set to 1 by the first timer RA prescaler underflow generated after the count starts. * When using the pulse period measurement mode, leave two or more periods of the timer RA prescaler immediately after the count starts, then set the TEDGF bit to 0. * The TCSTF bit retains 0 (count stops) for 0 to 1 cycle of the count source after setting the TSTART bit to 1 (count starts) while the count is stopped. During this time, do not access registers associated with timer RA(1) other than the TCSTF bit. Timer RA starts counting at the first valid edge of the count source after The TCSTF bit is set to 1 (during count). The TCSTF bit remains 1 for 0 to 1 cycle of the count source after setting the TSTART bit to 0 (count stops) while the count is in progress. Timer RA counting is stopped when the TCSTF bit is set to 0. During this time, do not access registers associated with timer RA(1) other than the TCSTF bit. NOTE: 1. Registers associated with timer RA: TRACR, TRAIOC, TRAMR, TRAPRE, and TRA. * When the TRAPRE register is continuously written during count operation (TCSTF bit is set to 1), allow three or more cycles of the count source clock for each write interval. * When the TRA register is continuously written during count operation (TCSTF bit is set to 1), allow three or more cycles of the prescaler underflow for each write interval. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 151 of 450 R8C/2K Group, R8C/2L Group 16.2 16. Timers Timer RB Timer RB is an 8-bit timer with an 8-bit prescaler. The prescaler and timer each consist of a reload register and counter (refer to Tables 16.7 to 16.10 the Specifications of Each Mode). Timer RB has timer RB primary and timer RB secondary as reload registers. The count source for timer RB is the operating clock that regulates the timing of timer operations such as counting and reloading. Figure 16.12 shows a Block Diagram of Timer RB. Figures 16.13 to 16.16 show the registers associated with timer RB. Timer RB has four operation modes listed as follows: * Timer mode: * Programmable waveform generation mode: * Programmable one-shot generation mode: * Programmable wait one-shot generation mode: Reload register TCK1 to TCK0 bits f1 f8 = 00b Timer RA underflow = 10b = 11b f2 The timer counts an internal count source (peripheral function clock or timer RA underflows). The timer outputs pulses of a given width successively. The timer outputs a one-shot pulse. The timer outputs a delayed one-shot pulse. Data bus TRBSC register Reload register TRBPR register Reload register TCKCUT bit = 01b Counter TRBPRE register (prescaler) Timer RB interrupt Counter (timer RB) (Timer) TMOD1 to TMOD0 bits = 10b or 11b TSTRAT bit TOSSTF bit INT0 interrupt Digital filter INT0 pin Input polarity selected to be one edge or both edges INT0PL bit TMOD1 to TMOD0 bits = 01b, 10b, 11b INT0EN bit Polarity select INOSEG bit TOPL = 1 TOCNT = 0 TRBO pin P3_1 bit in P3 register TOCNT = 1 TSTART, TCSTF: Bits in TRBCR register TOSSTF: Bit in TRBOCR register TOPL, TOCNT, INOSTG, INOSEG: Bits in TRBIOC register TMOD1 to TMOD0, TCK1 to TCK0, TCKCUT: Bits in TRBMR register Figure 16.12 Block Diagram of Timer RB Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 152 of 450 INOSTG bit TOPL = 0 Q Toggle flip-flop Q CLR CK TCSTF bit TMOD1 to TMOD0 bits = 01b, 10b, 11b R8C/2K Group, R8C/2L Group 16. Timers Pin Select Register 2 b7 b0 Symbol PINSR2 Set to "40h" w hen using Timer RB. Do not set values other than "40h". When read, its content is undefined. Figure 16.13 PINSR2 Register Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 153 of 450 Address 00F6h Function After Reset Undefined RW WO R8C/2K Group, R8C/2L Group 16. Timers Timer RB Control Register b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRBCR Bit Symbol TSTART Address 0108h Bit Name Timer RB count start bit(1) After Reset 00h Function 0 : Count stops 1 : Count starts RW RW TCSTF Timer RB count status flag(1) 0 : Count stops 1 : During count(3) RO TSTOP Timer RB count forcible stop When this bit is set to 1, the count is forcibly bit(1, 2) stopped. When read, its content is 0. RW -- (b7-b3) Nothing is assigned. If necessary, set to 0. When read, the content is 0. -- NOTES: 1. Refer to 16.2.5 Notes on Tim er RB for precautions regarding bits TSTART, TCSTF and TSTOP. 2. When the TSTOP bit is set to 1, registers TRBPRE, TRBSC, TRBPR, and bits TSTART and TCSTF, and the TOSSTF bit in the TRBOCR register are set to values after a reset. 3. Indicates that count operation is in progress in timer mode or programmable w aveform mode. In programmable oneshot generation mode or programmable w ait one-shot generation mode, indicates that a one-shot pulse trigger has been acknow ledged. Timer RB One-Shot Control Register(2) b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRBOCR Bit Symbol TOSST Address 0109h Bit Name Timer RB one-shot start bit After Reset 00h Function When this bit is set to 1, one-shot trigger generated. When read, its content is 0. Timer RB one-shot stop bit When this bit is set to 1, counting of one-shot pulses (including programmable w ait one-shot pulses) stops. When read, its content is 0. RW 0 : One-shot stopped 1 : One-shot operating (Including w ait period) RO TOSSP TOSSTF Timer RB one-shot status flag(1) -- (b7-b3) Nothing is assigned. If necessary, set to 0. When read, the content is 0. RW RW NOTES: 1. When 1 is set to the TSTOP bit in the TRBCR register, the TOSSTF bit is set to 0. 2. This register is enabled w hen bits TMOD1 to TMOD0 in the TRBMR register is set to 10b (programmable one-shot generation mode) or 11b (programmable w ait one-shot generation mode). Figure 16.14 Registers TRBCR and TRBOCR Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 154 of 450 -- R8C/2K Group, R8C/2L Group 16. Timers Timer RB I/O Control Register b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRBIOC Bit Symbol TOPL TOCNT INOSTG Address After Reset 010Ah 00h Bit Name Function Timer RB output level select Function varies depending on operating mode. bit Timer RB output sw itch bit RW RW RW One-shot trigger control bit RW INOSEG One-shot trigger polarity select bit RW -- (b7-b4) Nothing is assigned. If necessary, set to 0. When read, the content is 0. -- Timer RB Mode Register b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRBMR Bit Symbol TMOD0 Address 010Bh Bit Name Timer RB operating mode select bits (1) TMOD1 -- (b2) TWRC TCK0 TCKCUT RW b1 b0 0 0 : Timer mode 0 1 : Programmable w aveform generation mode 1 0 : Programmable one-shot generation mode 1 1 : Programmable w ait one-shot generation mode Nothing is assigned. If necessary, set to 0. When read, the content is 0. Timer RB w rite control bit(2) 0 : Write to reload register and counter 1 : Write to reload register only Timer RB count source select bits (1) b5 b4 TCK1 -- (b6) After Reset 00h Function 0 0 : f1 0 1 : f8 1 0 : Timer RA underflow 1 1 : f2 RW RW -- RW RW RW Nothing is assigned. If necessary, set to 0. When read, the content is 0. -- Timer RB count source cutoff bit(1) RW 0 : Provides count source 1 : Cuts off count source NOTES: 1. Change bits TMOD1 and TMOD0; TCK1 and TCK0; and TCKCUT w hen both the TSTART and TCSTF bits in the TRBCR register set to 0 (count stops). 2. The TWRC bit can be set to either 0 or 1 in timer mode. In programmable w aveform generation mode, programmable one-shot generation mode, or programmable w ait one-shot generation mode, the TWRC bit must be set to 1 (w rite to reload register only). Figure 16.15 Registers TRBIOC and TRBMR Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 155 of 450 R8C/2K Group, R8C/2L Group 16. Timers Timer RB Prescaler Register(1) b7 b0 Symbol TRBPRE Mode Timer mode Address 010Ch Function Counts an internal count source or timer RA underflow s After Reset FFh Setting Range 00h to FFh Programmable w aveform generation mode 00h to FFh Programmable one-shot generation mode 00h to FFh Programmable w ait one-shot generation mode 00h to FFh RW RW RW RW RW NOTE: 1. When the TSTOP bit in the TRBCR register is set to 1, the TRBPRE register is set to FFh. Timer RB Secondary Register(3, 4) b7 b0 Symbol TRBSC Mode Timer mode Address 010Dh Function Disabled After Reset FFh Setting Range 00h to FFh Programmable w aveform generation mode Counts timer RB prescaler underflow s (1) 00h to FFh Programmable one-shot generation mode Disabled 00h to FFh Programmable w ait one-shot Counts timer RB prescaler underflow s generation mode (one-shot w idth is counted) 00h to FFh RW -- WO(2) -- WO(2) NOTES: 1. The values of registers TRBPR and TRBSC are reloaded to the counter alternately and counted. 2. The count value can be read out by reading the TRBPR register even w hen the secondary period is being counted. 3. When the TSTOP bit in the TRBCR register is set to 1, the TRBSC register is set to FFh. 4. To w rite to the TRBSC register, perform the follow ing steps. (1) Write the value to the TRBSC register. (2) Write the value to the TRBPR register. (If the value does not change, w rite the same value second time.) Timer RB Primary Register(2) b7 b0 Symbol TRBPR Mode Timer mode Address 010Eh Function Counts timer RB prescaler underflow s After Reset FFh Setting Range 00h to FFh Programmable w aveform generation mode Counts timer RB prescaler underflow s (1) 00h to FFh Programmable one-shot generation mode Counts timer RB prescaler underflow s (one-shot w idth is counted) 00h to FFh Programmable w ait one-shot Counts timer RB prescaler underflow s generation mode (w ait period w idth is counted) 00h to FFh NOTES: 1. The values of registers TRBPR and TRBSC are reloaded to the counter alternately and counted. 2. When the TSTOP bit in the TRBCR register is set to 1, the TRBPR register is set to FFh. Figure 16.16 Registers TRBPRE, TRBSC, and TRBPR Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 156 of 450 RW RW RW RW RW R8C/2K Group, R8C/2L Group 16.2.1 16. Timers Timer Mode In timer mode, a count source which is internally generated or timer RA underflows are counted (refer to Table 16.7 Timer Mode Specifications). Registers TRBOCR and TRBSC are not used in timer mode. Figure 16.17 shows the TRBIOC Register in Timer Mode. Table 16.7 Timer Mode Specifications Item Count sources Count operations Specification Divide ratio Count start condition Count stop conditions Interrupt request generation timing TRBO pin function f1, f2, f8, timer RA underflow * Decrement * When the timer underflows, it reloads the reload register contents before the count continues (when timer RB underflows, the contents of timer RB primary reload register is reloaded). 1/(n+1)(m+1) n: setting value in TRBPRE register, m: setting value in TRBPR register 1 (count starts) is written to the TSTART bit in the TRBCR register. * 0 (count stops) is written to the TSTART bit in the TRBCR register. * 1 (count forcibly stop) is written to the TSTOP bit in the TRBCR register. When timer RB underflows [timer RB interrupt]. Programmable I/O port INT0 pin function Read from timer Write to timer Programmable I/O port or INT0 interrupt input The count value can be read out by reading registers TRBPR and TRBPRE. * When registers TRBPRE and TRBPR are written while the count is stopped, values are written to both the reload register and counter. * When registers TRBPRE and TRBPR are written to while count operation is in progress: If the TWRC bit in the TRBMR register is set to 0, the value is written to both the reload register and the counter. If the TWRC bit is set to 1, the value is written to the reload register only. (Refer to 16.2.1.1 Timer Write Control during Count Operation.) Timer RB I/O Control Register b7 b6 b5 b4 b3 b2 b1 b0 0 0 0 0 Symbol TRBIOC Bit Symbol TOPL TOCNT INOSTG Figure 16.17 Address After Reset 010Ah 00h Bit Name Function Timer RB output level select Set to 0 in timer mode. bit Timer RB output sw itch bit One-shot trigger control bit RW RW RW INOSEG One-shot trigger polarity select bit RW -- (b7-b4) Nothing is assigned. If necessary, set to 0. When read, the content is 0. -- TRBIOC Register in Timer Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 RW Page 157 of 450 R8C/2K Group, R8C/2L Group 16.2.1.1 16. Timers Timer Write Control during Count Operation Timer RB has a prescaler and a timer (which counts the prescaler underflows). The prescaler and timer each consist of a reload register and a counter. In timer mode, the TWRC bit in the TRBMR register can be used to select whether writing to the prescaler or timer during count operation is performed to both the reload register and counter or only to the reload register. However, values are transferred from the reload register to the counter of the prescaler in synchronization with the count source. In addition, values are transferred from the reload register to the counter of the timer in synchronization with prescaler underflows. Therefore, even if the TWRC bit is set for writing to both the reload register and counter, the counter value is not updated immediately after the WRITE instruction is executed. In addition, if the TWRC bit is set for writing to the reload register only, the synchronization of the writing will be shifted if the prescaler value changes. Figure 16.18 shows an Operating Example of Timer RB when Counter Value is Rewritten during Count Operation. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 158 of 450 R8C/2K Group, R8C/2L Group 16. Timers When the TWRC bit is set to 0 (write to reload register and counter) Set 01h to the TRBPRE register and 25h to the TRBPR register by a program. Count source After writing, the reload register is written with the first count source. Reloads register of timer RB prescaler Previous value Counter of timer RB prescaler 06h 05h New value (01h) 04h Reload with the second count source Reload on underflow 01h 01h 00h 00h 01h 00h 01h 00h After writing, the reload register is written on the first underflow. Reloads register of timer RB Previous value New value (25h) Reload on the second underflow Counter of timer RB IR bit in TRBIC register 03h 02h 25h 24h 0 The IR bit remains unchanged until underflow is generated by a new value. When the TWRC bit is set to 1 (write to reload register only) Set 01h to the TRBPRE register and 25h to the TRBPR register by a program. Count source After writing, the reload register is written with the first count source. Reloads register of timer RB prescaler Previous value New value (01h) Reload on underflow Counter of timer RB prescaler 06h 05h 04h 03h 02h 01h 00h 01h 00h 01h 00h 01h 00h 01h After writing, the reload register is written on the first underflow. Reloads register of timer RB Previous value New value (25h) Reload on underflow Counter of timer RB IR bit in TRBIC register 03h 02h 01h 00h 25h 0 Only the prescaler values are updated, extending the duration until timer RB underflow. The above applies under the following conditions. Both bits TSTART and TCSTF in the TRBCR register are set to 1 (During count). Figure 16.18 Operating Example of Timer RB when Counter Value is Rewritten during Count Operation Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 159 of 450 R8C/2K Group, R8C/2L Group 16.2.2 16. Timers Programmable Waveform Generation Mode In programmable waveform generation mode, the signal output from the TRBO pin is inverted each time the counter underflows, while the values in registers TRBPR and TRBSC are counted alternately (refer to Table 16.8 Programmable Waveform Generation Mode Specifications). Counting starts by counting the setting value in the TRBPR register. The TRBOCR register is unused in this mode. Figure 16.19 shows the TRBIOC Register in Programmable Waveform Generation Mode. Figure 16.20 shows an Operating Example of Timer RB in Programmable Waveform Generation Mode. Table 16.8 Programmable Waveform Generation Mode Specifications Item Count sources Count operations Width and period of output waveform Count start condition Count stop conditions Interrupt request generation timing TRBO pin function INT0 pin function Read from timer Write to timer Select functions Specification f1, f2, f8, timer RA underflow * Decrement * When the timer underflows, it reloads the contents of the primary reload and secondary reload registers alternately before the count continues. Primary period: (n+1)(m+1)/fi Secondary period: (n+1)(p+1)/fi Period: (n+1){(m+1)+(p+1)}/fi fi: Count source frequency n: Value set in TRBPRE register m: Value set in TRBPR register p: Value set in TRBSC register 1 (count start) is written to the TSTART bit in the TRBCR register. * 0 (count stop) is written to the TSTART bit in the TRBCR register. * 1 (count forcibly stop) is written to the TSTOP bit in the TRBCR register. In half a cycle of the count source, after timer RB underflows during the secondary period (at the same time as the TRBO output change) [timer RB interrupt] Programmable output port or pulse output Programmable I/O port or INT0 interrupt input The count value can be read out by reading registers TRBPR and TRBPRE(1). * When registers TRBPRE, TRBSC, and TRBPR are written while the count is stopped, values are written to both the reload register and counter. * When registers TRBPRE, TRBSC, and TRBPR are written to during count operation, values are written to the reload registers only.(2) * Output level select function The TOPL bit in the TRBIOC register selects the output level during primary and secondary periods. * TRBO pin output switch function Timer RB pulse output or P1_3 latch output is selected by the TOCNT bit in the TRBIOC register.(3) NOTES: 1. Even when counting the secondary period, the TRBPR register may be read. 2. The set values are reflected in the waveform output beginning with the following primary period after writing to the TRBPR register. 3. The value written to the TOCNT bit is enabled by the following. * When counting starts. * When a timer RB interrupt request is generated. The contents after the TOCNT bit is changed are reflected from the output of the following primary period. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 160 of 450 R8C/2K Group, R8C/2L Group 16. Timers Timer RB I/O Control Register b7 b6 b5 b4 b3 b2 b1 b0 0 0 Symbol TRBIOC Bit Symbol TOPL TOCNT INOSTG Figure 16.19 Address 010Ah Bit Name Timer RB output level select 0 : Outputs bit Outputs Outputs 1 : Outputs Outputs Outputs After Reset 00h Function "H" for primary period "L" for secondary period "L" w hen the timer is stopped "L" for primary period "H" for secondary period "H" w hen the timer is stopped RW Timer RB output sw itch bit 0 : Outputs timer RB w aveform 1 : Outputs value in P1_3 port register RW One-shot trigger control bit Set to 0 in programmable w aveform generation mode. RW INOSEG One-shot trigger polarity select bit RW -- (b7-b4) Nothing is assigned. If necessary, set to 0. When read, the content is 0. -- TRBIOC Register in Programmable Waveform Generation Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 RW Page 161 of 450 R8C/2K Group, R8C/2L Group 16. Timers Set to 1 by program TSTART bit in TRBCR register 1 0 Count source Timer RB prescaler underflow signal Timer RB secondary reloads 01h Counter of timer RB 00h 02h 01h Timer RB primary reloads 00h 01h 00h 02h Set to 0 when interrupt request is acknowledged, or set by program. IR bit in TRBIC register 1 0 Set to 0 by program TOPL bit in TRBIO register 1 0 Waveform output starts Waveform output inverted Waveform output starts 1 TRBO pin output 0 Initial output is the same level as during secondary period. Primary period Secondary period Primary period The above applies under the following conditions. TRBPRE = 01h, TRBPR = 01h, TRBSC = 02h TRBIOC register TOCNT = 0 (timer RB waveform is output from the TRBO pin) Figure 16.20 Operating Example of Timer RB in Programmable Waveform Generation Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 162 of 450 R8C/2K Group, R8C/2L Group 16.2.3 16. Timers Programmable One-shot Generation Mode In programmable one-shot generation mode, a one-shot pulse is output from the TRBO pin by a program or an external trigger input (input to the INT0 pin) (refer to Table 16.9 Programmable One-Shot Generation Mode Specifications). When a trigger is generated, the timer starts operating from the point only once for a given period equal to the set value in the TRBPR register. The TRBSC register is not used in this mode. Figure 16.21 shows the TRBIOC Register in Programmable One-Shot Generation Mode. Figure 16.22 shows an Operating Example of Programmable One-Shot Generation Mode. Table 16.9 Programmable One-Shot Generation Mode Specifications Item Count sources Count operations Specification f1, f2, f8, timer RA underflow * Decrement the setting value in the TRBPR register * When the timer underflows, it reloads the contents of the reload register before the count completes and the TOSSTF bit is set to 0 (one-shot stops). * When the count stops, the timer reloads the contents of the reload register before it stops. One-shot pulse (n+1)(m+1)/fi output time fi: Count source frequency, n: Setting value in TRBPRE register, m: Setting value in TRBPR register(2) Count start conditions * The TSTART bit in the TRBCR register is set to 1 (count starts) and the next trigger is generated * Set the TOSST bit in the TRBOCR register to 1 (one-shot starts) * Input trigger to the INT0 pin Count stop conditions * When reloading completes after timer RB underflows during primary period * When the TOSSP bit in the TRBOCR register is set to 1 (one-shot stops) * When the TSTART bit in the TRBCR register is set to 0 (stops counting) * When the TSTOP bit in the TRBCR register is set to 1 (forcibly stops counting) Interrupt request In half a cycle of the count source, after the timer underflows (at the same time as generation timing the TRBO output ends) [timer RB interrupt] TRBP pin function Pulse output INT0 pin functions Read from timer Write to timer Select functions * When the INOSTG bit in the TRBIOC register is set to 0 (INT0 one-shot trigger disabled): programmable I/O port or INT0 interrupt input * When the INOSTG bit in the TRBIOC register is set to 1 (INT0 one-shot trigger enabled): external trigger (INT0 interrupt input) The count value can be read out by reading registers TRBPR and TRBPRE. * When registers TRBPRE and TRBPR are written while the count is stopped, values are written to both the reload register and counter. * When registers TRBPRE and TRBPR are written during the count, values are written to the reload register only (the data is transferred to the counter at the following reload)(1). * Output level select function The TOPL bit in the TRBIOC register selects the output level of the one-shot pulse waveform. * One-shot trigger select function Refer to 16.2.3.1 One-Shot Trigger Selection. NOTES: 1. The set value is reflected at the following one-shot pulse after writing to the TRBPR register. 2. Do not set both the TRBPRE and TRBPR registers to 00h. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 163 of 450 R8C/2K Group, R8C/2L Group 16. Timers Timer RB I/O Control Register b7 b6 b5 b4 b3 b2 b1 b0 0 Symbol TRBIOC Bit Symbol TOPL TOCNT Address 010Ah Bit Name Timer RB Output Level Select Bit Timer RB Output Sw itch Bit 0 : Outputs Outputs 1 : Outputs Outputs After Reset 00h Function one-shot pulse "H" "L" w hen the timer is stopped one-shot pulse "L" "H" w hen the timer is stopped Set to 0 in programmable one-shot generation mode. INOSTG One-Shot Trigger Control Bit(1) INOSEG One-Shot Trigger Polarity Select Bit(1) -- (b7-b4) Nothing is assigned. if necessary, set to 0. When read, its content is 0. 0 : INT0 pin one-shot trigger disabled _____ 1 : INT0 pin one-shot trigger enabled 0 : Falling edge trigger 1 : Rising edge trigger TRBIOC Register in Programmable One-Shot Generation Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 164 of 450 RW RW _____ NOTE: 1. Refer to 16.2.3.1 One-Shot Trigger Selection. Figure 16.21 RW RW RW -- R8C/2K Group, R8C/2L Group 16. Timers Set to 1 by program TSTART bit in TRBCR register 1 0 Set to 0 when counting ends Set to 1 by program TOSSTF bit in TRBOCR register Set to 1 by INT0 pin input trigger 1 0 INT0 pin input Count source Timer RB prescaler underflow signal Count starts 01h Counter of timer RB Timer RB primary reloads 00h Count starts 01h Timer RB primary reloads 00h 01h Set to 0 when interrupt request is acknowledged, or set by program IR bit in TRBIC register 1 0 Set to 0 by program TOPL bit in TRBIOC register 1 0 Waveform output starts Waveform output ends Waveform output starts 1 TRBIO pin output 0 The above applies under the following conditions. TRBPRE = 01h, TRBPR = 01h TRBIOC register TOPL = 0, TOCNT = 0 INOSTG = 1 (INT0 one-shot trigger enabled) INOSEG = 1 (edge trigger at rising edge) Figure 16.22 Operating Example of Programmable One-Shot Generation Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 165 of 450 Waveform output ends R8C/2K Group, R8C/2L Group 16.2.3.1 16. Timers One-Shot Trigger Selection In programmable one-shot generation mode and programmable wait one-shot generation mode, operation starts when a one-shot trigger is generated while the TCSTF bit in the TRBCR register is set to 1 (count starts). A one-shot trigger can be generated by either of the following causes: * 1 is written to the TOSST bit in the TRBOCR register by a program. * Trigger input from the INT0 pin. When a one-shot trigger occurs, the TOSSTF bit in the TRBOCR register is set to 1 (one-shot operation in progress) after one or two cycles of the count source have elapsed. Then, in programmable one-shot generation mode, count operation begins and one-shot waveform output starts. (In programmable wait one-shot generation mode, count operation starts for the wait period.) If a one-shot trigger occurs while the TOSSTF bit is set to 1, no retriggering occurs. To use trigger input from the INT0 pin, input the trigger after making the following settings: * Set the PD4_5 bit in the PD4 register to 0 (input port). * Select the INT0 digital filter with bits INT0F1 and INT0F0 in the INTF register. * Select both edges or one edge with the INT0PL bit in INTEN register. If one edge is selected, further select falling or rising edge with the INOSEG bit in TRBIOC register. * Set the INT0EN bit in the INTEN register to 0 (enabled). * After completing the above, set the INOSTG bit in the TRBIOC register to 1 (INT pin one-shot trigger enabled). Note the following points with regard to generating interrupt requests by trigger input from the INT0 pin. * Processing to handle the interrupts is required. Refer to 12. Interrupts, for details. * If one edge is selected, use the POL bit in the INT0IC register to select falling or rising edge. (The INOSEG bit in the TRBIOC register does not affect INT0 interrupts). * If a one-shot trigger occurs while the TOSSTF bit is set to 1, timer RB operation is not affected, but the value of the IR bit in the INT0IC register changes. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 166 of 450 R8C/2K Group, R8C/2L Group 16.2.4 16. Timers Programmable Wait One-Shot Generation Mode In programmable wait one-shot generation mode, a one-shot pulse is output from the TRBO pin by a program or an external trigger input (input to the INT0 pin) (refer to Table 16.10 Programmable Wait One-Shot Generation Mode Specifications). When a trigger is generated from that point, the timer outputs a pulse only once for a given length of time equal to the setting value in the TRBSC register after waiting for a given length of time equal to the setting value in the TRBPR register. Figure 16.23 shows the TRBIOC Register in Programmable Wait One-Shot Generation Mode. Figure 16.24 shows an Operating Example of Programmable Wait One-Shot Generation Mode. Table 16.10 Programmable Wait One-Shot Generation Mode Specifications Item Count sources Count operations Wait time One-shot pulse output time Count start conditions Count stop conditions Interrupt request generation timing TRBO pin function INT0 pin functions Read from timer Write to timer Select functions Specification f1, f2, f8, timer RA underflow * Decrement the timer RB primary setting value. * When a count of the timer RB primary underflows, the timer reloads the contents of timer RB secondary before the count continues. * When a count of the timer RB secondary underflows, the timer reloads the contents of timer RB primary before the count completes and the TOSSTF bit is set to 0 (one-shot stops). * When the count stops, the timer reloads the contents of the reload register before it stops. (n+1)(m+1)/fi fi: Count source frequency n: Value set in the TRBPRE register, m Value set in the TRBPR register(2) (n+1)(p+1)/fi fi: Count source frequency n: Value set in the TRBPRE register, p: Value set in the TRBSC register * The TSTART bit in the TRBCR register is set to 1 (count starts) and the next trigger is generated. * Set the TOSST bit in the TRBOCR register to 1 (one-shot starts). * Input trigger to the INT0 pin * When reloading completes after timer RB underflows during secondary period. * When the TOSSP bit in the TRBOCR register is set to 1 (one-shot stops). * When the TSTART bit in the TRBCR register is set to 0 (starts counting). * When the TSTOP bit in the TRBCR register is set to 1 (forcibly stops counting). In half a cycle of the count source after timer RB underflows during secondary period (complete at the same time as waveform output from the TRBO pin) [timer RB interrupt]. Pulse output * When the INOSTG bit in the TRBIOC register is set to 0 (INT0 one-shot trigger disabled): programmable I/O port or INT0 interrupt input * When the INOSTG bit in the TRBIOC register is set to 1 (INT0 one-shot trigger enabled): external trigger (INT0 interrupt input) The count value can be read out by reading registers TRBPR and TRBPRE. * When registers TRBPRE, TRBSC, and TRBPR are written while the count stops, values are written to both the reload register and counter. * When registers TRBPRE, TRBSC, and TRBPR are written to during count operation, values are written to the reload registers only.(1) * Output level select function The TOPL bit in the TRBIOC register selects the output level of the one-shot pulse waveform. * One-shot trigger select function Refer to 16.2.3.1 One-Shot Trigger Selection. NOTES: 1. The set value is reflected at the following one-shot pulse after writing to registers TRBSC and TRBPR. 2. Do not set both the TRBPRE and TRBPR registers to 00h. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 167 of 450 R8C/2K Group, R8C/2L Group 16. Timers Timer RB I/O Control Register b7 b6 b5 b4 b3 b2 b1 b0 0 Symbol TRBIOC Bit Symbol TOPL TOCNT Address 010Ah Bit Name Timer RB output level select 0 : Outputs bit Outputs w ait. 1 : Outputs Outputs w ait. Timer RB output sw itch bit one-shot pulse "L". "H" w hen the timer stops or during Set to 0 in programmable w ait one-shot generation mode. (1) INOSTG After Reset 00h Function one-shot pulse "H". "L" w hen the timer stops or during One-shot trigger control bit 0 : INT0 pin one-shot trigger disabled _____ 1 : INT0 pin one-shot trigger enabled 0 : Falling edge trigger 1 : Rising edge trigger INOSEG One-shot trigger polarity select bit(1) -- (b7-b4) Nothing is assigned. If necessary, set to 0. When read, the content is 0. TRBIOC Register in Programmable Wait One-Shot Generation Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 168 of 450 RW RW _____ NOTE: 1. Refer to 16.2.3.1 One-Shot Trigger Selection. Figure 16.23 RW RW RW -- R8C/2K Group, R8C/2L Group 16. Timers Set to 1 by program TSTART bit in TRBCR register 1 0 Set to 1 by setting 1 to TOSST bit in TRBOCR register, or INT0 pin input trigger. TOSSTF bit in TRBOCR register Set to 0 when counting ends 1 0 INT0 pin input Count source Timer RB prescaler underflow signal Count starts Counter of timer RB 01h Timer RB secondary reloads 00h 04h Timer RB primary reloads 03h 02h 01h 00h 01h Set to 0 when interrupt request is acknowledged, or set by program. IR bit in TRBIC register 1 TOPL bit in TRBIOC register 1 0 Set to 0 by program 0 Wait starts Waveform output starts Waveform output ends 1 TRBIO pin output 0 Wait (primary period) One-shot pulse (secondary period) The above applies under the following conditions. TRBPRE = 01h, TRBPR = 01h, TRBSC = 04h INOSTG = 1 (INT0 one-shot trigger enabled) INOSEG = 1 (edge trigger at rising edge) Figure 16.24 Operating Example of Programmable Wait One-Shot Generation Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 169 of 450 R8C/2K Group, R8C/2L Group 16.2.5 16. Timers Notes on Timer RB * Timer RB stops counting after a reset. Set the values in the timer RB and timer RB prescalers before the count starts. * Even if the prescaler and timer RB is read out in 16-bit units, these registers are read 1 byte at a time by the MCU. Consequently, the timer value may be updated during the period when these two registers are being read. * In programmable one-shot generation mode and programmable wait one-shot generation mode, when setting the TSTART bit in the TRBCR register to 0, 0 (stops counting) or setting the TOSSP bit in the TRBOCR register to 1 (stops one-shot), the timer reloads the value of reload register and stops. Therefore, in programmable one-shot generation mode and programmable wait one-shot generation mode, read the timer count value before the timer stops. * The TCSTF bit remains 0 (count stops) for 1 to 2 cycles of the count source after setting the TSTART bit to 1 (count starts) while the count is stopped. During this time, do not access registers associated with timer RB(1) other than the TCSTF bit. Timer RB starts counting at the first valid edge of the count source after the TCSTF bit is set to 1 (during count). The TCSTF bit remains 1 for 1 to 2 cycles of the count source after setting the TSTART bit to 0 (count stops) while the count is in progress. Timer RB counting is stopped when the TCSTF bit is set to 0. During this time, do not access registers associated with timer RB(1) other than the TCSTF bit. NOTE: 1. Registers associated with timer RB: TRBCR, TRBOCR, TRBIOC, TRBMR, TRBPRE, TRBSC, and TRBPR. * If the TSTOP bit in the TRBCR register is set to 1 during timer operation, timer RB stops immediately. * If 1 is written to the TOSST or TOSSP bit in the TRBOCR register, the value of the TOSSTF bit changes after one or two cycles of the count source have elapsed. If the TOSSP bit is written to 1 during the period between when the TOSST bit is written to 1 and when the TOSSTF bit is set to 1, the TOSSTF bit may be set to either 0 or 1 depending on the content state. Likewise, if the TOSST bit is written to 1 during the period between when the TOSSP bit is written to 1 and when the TOSSTF bit is set to 0, the TOSSTF bit may be set to either 0 or 1. 16.2.5.1 Timer mode The following workaround should be performed in timer mode. To write to registers TRBPRE and TRBPR during count operation (TCSTF bit is set to 1), note the following points: * When the TRBPRE register is written continuously, allow three or more cycles of the count source for each write interval. * When the TRBPR register is written continuously, allow three or more cycles of the prescaler underflow for each write interval. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 170 of 450 R8C/2K Group, R8C/2L Group 16.2.5.2 16. Timers Programmable waveform generation mode The following three workarounds should be performed in programmable waveform generation mode. (1) To write to registers TRBPRE and TRBPR during count operation (TCSTF bit is set to 1), note the following points: * When the TRBPRE register is written continuously, allow three or more cycles of the count source for each write interval. * When the TRBPR register is written continuously, allow three or more cycles of the prescaler underflow for each write interval. (2) To change registers TRBPRE and TRBPR during count operation (TCSTF bit is set to 1), synchronize the TRBO output cycle using a timer RB interrupt, etc. This operation should be preformed only once in the same output cycle. Also, make sure that writing to the TRBPR register does not occur during period A shown in Figures 16.25 and 16.26. The following shows the detailed workaround examples. * Workaround example (a): As shown in Figure 16.25, write to registers TRBSC and TRBPR in the timer RB interrupt routine. These write operations must be completed by the beginning of period A. Period A Count source/ prescaler underflow signal TRBO pin output IR bit in TRBIC register Primary period (a) Interrupt request is acknowledged Secondary period Ensure sufficient time (b) Interrupt request is generated Instruction in Interrupt sequence interrupt routine Set the secondary and then the primary register immediately (a) Period between interrupt request generation and the completion of execution of an instruction. The length of time varies depending on the instruction being executed. The DIVX instruction requires the longest time, 30 cycles (assuming no wait states and that a register is set as the divisor). (b) 20 cycles. 21 cycles for address match and single-step interrupts. Figure 16.25 Workaround Example (a) When Timer RB interrupt is Used Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 171 of 450 R8C/2K Group, R8C/2L Group 16. Timers * Workaround example (b): As shown in Figure 16.26 detect the start of the primary period by the TRBO pin output level and write to registers TRBSC and TRBPR. These write operations must be completed by the beginning of period A. If the port register's bit value is read after the port direction register's bit corresponding to the TRBO pin is set to 0 (input mode), the read value indicates the TRBO pin output value. Period A Count source/ prescaler underflow signal TRBO pin output Read value of the port register's bit corresponding to the TRBO pin (when the bit in the port direction register is set to 0) Secondary period Primary period (i) (ii) (iii) Ensure sufficient time The TRBO output inversion is detected at the end of the secondary period. Figure 16.26 Upon detecting (i), set the secondary and then the primary register immediately. Workaround Example (b) When TRBO Pin Output Value is Read (3) To stop the timer counting in the primary period, use the TSTOP bit in the TRBCR register. In this case, registers TRBPRE and TRBPR are initialized and their values are set to the values after reset. 16.2.5.3 Programmable one-shot generation mode The following two workarounds should be performed in programmable one-shot generation mode. (1) To write to registers TRBPRE and TRBPR during count operation (TCSTF bit is set to 1), note the following points: * When the TRBPRE register is written continuously during count operation (TCSTF bit is set to 1), allow three or more cycles of the count source for each write interval. * When the TRBPR register is written continuously during count operation (TCSTF bit is set to 1), allow three or more cycles of the prescaler underflow for each write interval. (2) Do not set both the TRBPRE and TRBPR registers to 00h. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 172 of 450 R8C/2K Group, R8C/2L Group 16.2.5.4 16. Timers Programmable wait one-shot generation mode The following three workarounds should be performed in programmable wait one-shot generation mode. (1) To write to registers TRBPRE and TRBPR during count operation (TCSTF bit is set to 1), note the following points: * When the TRBPRE register is written continuously, allow three or more cycles of the count source for each write interval. * When the TRBPR register is written continuously, allow three or more cycles of the prescaler underflow for each write interval. (2) Do not set both the TRBPRE and TRBPR registers to 00h. (3) Set registers TRBSC and TRBPR using the following procedure. (a) To use "INT0 pin one-shot trigger enabled" as the count start condition Set the TRBSC register and then the TRBPR register. At this time, after writing to the TRBPR register, allow an interval of 0.5 or more cycles of the count source before trigger input from the INT0 pin. (b) To use "writing 1 to TOSST bit" as the start condition Set the TRBSC register, the TRBPR register, and then TOSST bit. At this time, after writing to the TRBPR register, allow an interval of 0.5 or more cycles of the count source before writing to the TOSST bit. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 173 of 450 R8C/2K Group, R8C/2L Group 16.3 16. Timers Timer RC 16.3.1 Overview Timer RC is a 16-bit timer with four I/O pins. Timer RC uses either f1 or fOCO40M as its operation clock. Table 16.11 lists the Timer RC Operation Clock. Table 16.11 Timer RC Operation Clock Condition Timer RC Operation Clock Count source is f1, f2, f4, f8, f32, or TRCCLK input (bits TCK2 to TCK0 in f1 TRCCR1 register are set to a value from 000b to 101b) Count source is fOCO40M (bits TCK2 to TCK0 in TRCCR1 register are set fOCO40M to 110b) Table 16.12 lists the Timer RC I/O Pins, and Figure 16.27 shows a Timer RC Block Diagram. Timer RC has three modes. * Timer mode - Input capture function The counter value is captured to a register, using an external signal as the trigger. - Output compare function Matches between the counter and register values are detected. (Pin output state changes when a match is detected.) The following two modes use the output compare function. * PWM mode Pulses of a given width are output continuously. * PWM2 mode A one-shot waveform or PWM waveform is output following the trigger after the wait time has elapsed. Input capture function, output compare function, and PWM mode settings may be specified independently for each pin. In PWM2 mode waveforms are output based on a combination of the counter or the register. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 174 of 450 R8C/2K Group, R8C/2L Group 16. Timers f1, f2, f4, f8, f32, fOCO40M TRCMR register TRCCR1 register TRCIER register INT0 Count source select circuit TRCSR register TRCIOR0 register TRCIOA/TRCTRG TRCIOR1 register Data bus TRCCLK TRCIOB Timer RC control circuit TRC register TRCGRA register TRCIOC TRCIOD TRCGRB register TRCGRC register TRCGRD register TRCCR2 register TRCDF register Timer RC interrupt request TRCOER register Figure 16.27 Table 16.12 Timer RC Block Diagram Timer RC I/O Pins Pin Name TRCIOA(P1_1) TRCIOB(P1_2) TRCIOC(P3_4) TRCIOD(P3_5) TRCCLK(P3_3) TRCTRG(P1_1) Rev.1.10 Dec 21, 2007 REJ09B0406-0110 I/O I/O Function Function differs according to the mode. Refer to descriptions of individual modes for details Input Input External clock input PWM2 mode external trigger input Page 175 of 450 R8C/2K Group, R8C/2L Group 16.3.2 16. Timers Registers Associated with Timer RC Table 16.13 lists the Registers Associated with Timer RC. Figures 16.28 to 16.38 show details of the registers associated with timer RC. Table 16.13 Registers Associated with Timer RC 00F7h PINSR3 Mode Timer Input Output PWM Capture Compare Function Function Valid Valid Valid 0120h TRCMR Valid Valid Valid Valid 0121h TRCCR1 Valid Valid Valid Valid 0122h TRCIER Valid Valid Valid Valid 0123h TRCSR Valid Valid Valid Valid 0124h TRCIOR0 Valid Valid - - 0125h TRCIOR1 0126h 0127h 0128h 0129h 012Ah 012Bh 012Ch 012Dh 012Eh 012Fh 0130h TRC Valid Valid Valid Valid TRCGRA Valid Valid Valid Valid TRCCR2 - - - Valid 0131h TRCDF Valid - - Valid 0132h TRCOER - Valid Valid Valid Address Symbol PWM2 Valid TRCGRB Related Information Pin Select Register 3 Figure 16.28 PINSR3 Register Timer RC mode register Figure 16.29 TRCMR Register Timer RC control register 1 Figure 16.30 TRCCR1 Register Figure 16.51 TRCCR1 Register for Output Compare Function Figure 16.54 TRCCR1 Register in PWM Mode Figure 16.58 TRCCR1 Register in PWM2 Mode Timer RC interrupt enable register Figure 16.31 TRCIER Register Timer RC status register Figure 16.32 TRCSR Register Timer RC I/O control register 0, timer RC I/O control register 1 Figure 16.38 Registers TRCIOR0 and TRCIOR1 Figure 16.45 TRCIOR0 Register for Input Capture Function Figure 16.46 TRCIOR1 Register for Input Capture Function Figure 16.49 TRCIOR0 Register for Output Compare Function Figure 16.50 TRCIOR1 Register for Output Compare Function Timer RC counter Figure 16.33 TRC Register Timer RC general registers A, B, C, and D Figure 16.34 Registers TRCGRA, TRCGRB, TRCGRC, and TRCGRD TRCGRC TRCGRD - : Invalid Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 176 of 450 Timer RC control register 2 Figure 16.35 TRCCR2 Register Timer RC digital filter function select register Figure 16.36 TRCDF Register Timer RC output mask enable register Figure 16.37 TRCOER Register R8C/2K Group, R8C/2L Group 16. Timers Pin Select Register 3 b7 b0 Symbol PINSR3 Address 00F7h Function After Reset Undefined RW Set to "1Fh" w hen using Timer RC. Do not set values other than "1Fh". When read, its content is undefined. Figure 16.28 WO PINSR3 Register Timer RC Mode Register(1) b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRCMR Bit Symbol Address 0120h Bit Name PWM mode of TRCIOB select bit(2) After Reset 01001000b Function RW 0 : Timer mode 1 : PWM mode RW PWM mode of TRCIOD select bit 0 : Timer mode 1 : PWM mode RW PWM2 mode select bit 0 : PWM 2 mode 1 : Timer mode or PWM mode RW BFC TRCGRC register function select bit(3) 0 : General register 1 : Buffer register of TRCGRA register RW BFD TRCGRD register function select bit 0 : General register 1 : Buffer register of TRCGRB register RW -- (b6) Nothing is assigned. If necessary, set to 0. When read, the content is 1. PWMB (2) PWMC PWM mode of TRCIOC select bit (2) PWMD PWM2 TSTART TRC count start bit 0 : Count stops 1 : Count starts NOTES: 1. For notes on PWM2 mode, refer to 16.3.9.5 TRCMR Register in PWM2 Mode. 2. These bits are enabled w hen the PWM2 bit is set to 1 (timer mode or PWM mode). 3. Set the BFC bit to 0 (general register) in PWM2 mode. Figure 16.29 TRCMR Register Rev.1.10 Dec 21, 2007 REJ09B0406-0110 RW 0 : Timer mode 1 : PWM mode Page 177 of 450 -- RW R8C/2K Group, R8C/2L Group 16. Timers Timer RC Control Register 1 b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRCCR1 Bit Symbol TOA Address 0121h Bit Name TRCIOA output level select bit(1) After Reset 00h Function Function varies according to the operating mode (function).(2) RW RW (1) TOB TRCIOB output level select bit RW (1) TOC TRCIOC output level select bit RW (1) TOD TRCIOD output level select bit Count source select bits (1) RW b6 b5 b4 0 0 0 0 1 1 1 1 TCK0 TCK1 TCK2 TRC counter clear select bit(2, 3) CCLR 0 0 1 1 0 0 1 1 0 : f1 1 : f2 0 : f4 1 : f8 0 : f32 1 : TRCCLK input rising edge 0 : fOCO40M 1 : Do not set. RW 0 : Disable clear (free-running operation) 1 : Clear by compare match in the TRCGRA register RW RW RW NOTES: 1. Set to these bits w hen the TSTART bit in the TRCMR register is set to 0 (count stops). 2. Bits CCLR, TOA, TOB, TOC and TOD are disabled for the input capture function of the timer mode. 3. The TRC counter performs free-running operation for the input capture function of the timer mode independent of the CCLR bit setting. Figure 16.30 TRCCR1 Register Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 178 of 450 R8C/2K Group, R8C/2L Group 16. Timers Timer RC Interrupt Enable Register b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRCIER Bit Symbol IMIEA IMIEB IMIEC IMIED -- (b6-b4) Address 0122h Bit Name Input capture / compare match interrupt enable bit A After Reset 01110000b Function 0 : Disable interrupt (IMIA) by the IMFA bit 1 : Enable interrupt (IMIA) by the IMFA bit Input capture / compare match interrupt enable bit B 0 : Disable interrupt (IMIB) by the IMFB bit 1 : Enable interrupt (IMIB) by the IMFB bit RW Input capture / compare match interrupt enable bit C 0 : Disable interrupt (IMIC) by the IMFC bit 1 : Enable interrupt (IMIC) by the IMFC bit RW Input capture / compare match interrupt enable bit D 0 : Disable interrupt (IMID) by the IMFD bit 1 : Enable interrupt (IMID) by the IMFD bit RW Nothing is assigned. If necessary, set to 0. When read, the content is 1. Overflow interrupt enable bit OVIE Figure 16.31 TRCIER Register Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 179 of 450 0 : Disable interrupt (OVI) by the OVF bit 1 : Enable interrupt (OVI) by the OVF bit RW RW -- RW R8C/2K Group, R8C/2L Group 16. Timers Timer RC Status Register b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRCSR Bit Symbol IMFA Address 0123h Bit Name Input capture / compare match flag A After Reset 01110000b Function [Source for setting this bit to 0] Write 0 after read(1). [Source for setting this bit to 1] Refer to the table below . Input capture / compare match flag B IMFC Input capture / compare match flag C RW IMFD Input capture / compare match flag D RW Nothing is assigned. If necessary, set to 0. When read, the content is 1. -- Overflow flag OVF [Source for setting this bit to 0] Write 0 after read(1). [Source for setting this bit to 1] Refer to the table below . NOTE: 1. The w riting results are as follow s: * This bit is set to 0 w hen the read result is 1 and 0 is w ritten to the same bit. * This bit remains unchanged even if the read result is 0 and 0 is w ritten to the same bit. (This bit remains 1 even if it is set to 1 from 0 after reading, and w riting 0.) * This bit remains unchanged if 1 is w ritten to it. IMFA IMFB IMFC IMFD OVF Timer Mode PWM Mode PWM2 Mode Input capture Function Output Compare Function When the values of the registers TRC and TRCGRA match. TRCIOA pin input edge(1) TRCIOB pin input edge(1) When the values of the registers TRC and TRCGRB match. TRCIOC pin input edge(1) When the values of the registers TRC and TRCGRC match.(2) TRCIOD pin input edge(1) When the values of the registers TRC and TRCGRD match.(2) When the TRC register overflow s. NOTES: 1. Edge selected by bits IOj1 to IOj0 (j = A, B, C, or D). 2. Includes the condition that bits BFC and BFD are set to 1 (buffer registers of registers TRCGRA and TRCGRB). Figure 16.32 TRCSR Register Rev.1.10 Dec 21, 2007 REJ09B0406-0110 RW IMFB -- (b6-b4) Bit Symbol RW Page 180 of 450 RW RW R8C/2K Group, R8C/2L Group 16. Timers Timer RC Counter(1) (b15) b7 (b8) b0 b7 b0 Symbol TRC Address 0127h-0126h Function After Reset 0000h Setting Range Count a count source. Count operation is incremented. When an overflow occurs, the OVF bit in the TRCSR register is set to 1. RW 0000h to FFFFh RW NOTE: 1. Access the TRC register in 16-bit units. Do not access it in 8-bit units. Figure 16.33 TRC Register Timer RC General Register A, B, C and D(1) (b15) b7 (b8) b0 b7 b0 Symbol TRCGRA TRCGRB TRCGRC TRCGRD Address 0129h-0128h 012Bh-012Ah 012Dh-012Ch 012Fh-012Eh Function Function varies according to the operating mode. NOTE: 1. Access registers TRCGRA to TRCGRD in 16-bit units. Do not access them in 8-bit units. Figure 16.34 Registers TRCGRA, TRCGRB, TRCGRC, and TRCGRD Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 181 of 450 After Reset FFFFh FFFFh FFFFh FFFFh RW RW R8C/2K Group, R8C/2L Group 16. Timers Timer RC Control Register 2 b7 b6 b5 b4 b3 b2 b1 b0 Symbol Address TRCCR2 0130h Bit Symbol Bit Name -- Nothing is assigned. If necessary, set to 0. (b4-b0) When read, the content is 1. CSEL After Reset 00011111b Function TRC count operation select bit(1, 2) 0 : Count continues at compare match w ith the TRCGRA register 1 : Count stops at compare match w ith the TRCGRA register TRCTRG input edge select bits (3) b7 b6 TCEG0 TCEG1 0 0 : Disable the trigger input from the TRCTRG pin 0 1 : Rising edge selected 1 0 : Falling edge selected 1 1 : Both edges selected RW -- RW RW RW NOTES: 1. For notes on PWM2 mode, refer to 16.3.9.5 TRCMR Register in PWM2 Mode. 2. In timer mode and PWM mode this bit is disabled (the count operation continues independent of the CSEL bit setting). 3. In timer mode and PWM mode these bits are disabled. Figure 16.35 TRCCR2 Register Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 182 of 450 R8C/2K Group, R8C/2L Group 16. Timers Timer RC Digital Filter Function Select Register b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRCDF Bit Symbol DFA Address 0131h Bit Name TRCIOA pin digital filter function select bit(1) After Reset 00h Function 0 : Function is not used 1 : Function is used RW RW DFB TRCIOB pin digital filter function select bit(1) RW DFC TRCIOC pin digital filter function select bit(1) RW DFD TRCIOD pin digital filter function select bit(1) RW DFTRG TRCTRG pin digital filter function select bit(2) RW Nothing is assigned. If necessary, set to 0. When read, the content is 0. -- -- (b5) DFCK0 Clock select bits for digital filter function(1, 2) DFCK1 b7 b6 0 0 1 1 0 : f32 1 : f8 0 : f1 1 : Count source (clock selected by bits TCK2 to TCK0 in the TRCCR1 register) RW RW NOTES: 1. These bits are enabled for the input capture function. 2. These bits are enabled w hen in PWM2 mode and bits TCEG1 to TCEG0 in the TRCCR2 register are set to 01b, 10b, or 11b (TRCTRG trigger input enabled). Figure 16.36 TRCDF Register Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 183 of 450 R8C/2K Group, R8C/2L Group 16. Timers Timer RC Output Master Enable Register b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRCOER Bit Symbol Address 0132h Bit Name TRCIOA output disable bit(1) EA TRCIOB output disable bit(1) EB TRCIOC output disable bit(1) EC TRCIOD output disable bit(1) ED -- (b6-b4) After Reset 01111111b Function RW 0 : Enable output 1 : Disable output (The TRCIOA pin is used as a programmable I/O port.) RW 0 : Enable output 1 : Disable output (The TRCIOB pin is used as a programmable I/O port.) RW 0 : Enable output 1 : Disable output (The TRCIOC pin is used as a programmable I/O port.) RW 0 : Enable output 1 : Disable output (The TRCIOD pin is used as a programmable I/O port.) RW Nothing is assigned. If necessary, set to 0. When read, the content is 1. -- _____ PTO INT0 of pulse output forced cutoff signal input enabled bit 0 : Pulse output forced cutoff input disabled 1 : Pulse output forced cutoff input enabled (Bits EA, EB, EC, and ED are set to 1 (disable output) w hen "L" is applied to the _____ INT0 pin) NOTE: 1. These bits are disabled for input pins set to the input capture function. Figure 16.37 TRCOER Register Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 184 of 450 RW R8C/2K Group, R8C/2L Group 16. Timers Timer RC I/O Control Register 0(1) b7 b6 b5 b4 b3 b2 b1 b0 Symbol Address TRCIOR0 0124h Bit Symbol Bit Name IOA0 TRCGRA control bits IOA1 TRCGRA mode select bit(2) IOA2 IOA3 IOB0 IOB1 IOB2 -- (b7) After Reset 10001000b Function Function varies according to the operating mode (function). RW RW RW 0 : Output compare function 1 : Input capture function RW TRCGRA input capture input sw itch bit(4) 0 : fOCO128 signal 1 : TRCIOA pin input RW TRCGRB control bits Function varies according to the operating mode (function). RW RW TRCGRB mode select bit(3) 0 : Output compare function 1 : Input capture function RW Nothing is assigned. If necessary, set to 0. When read, the content is 1. -- NOTES: 1. The TRCIOR0 register is enabled in timer mode. It is disabled in modes PWM and PWM2. 2. When the BFC bit in the TRCMR register is set to 1 (buffer register of TRCGRA register), set the IOC2 bit in the TRCIOR1 register to the same value as the IOA2 bit in the TRCIOR0 register. 3. When the BFD bit in the TRCMR register is set to 1 (buffer register of TRCGRB register), set the IOD2 bit in the TRCIOR1 register to the same value as the IOB2 bit in the TRCIOR0 register. 4. The IOA3 bit is enabled w hen the IOA2 bit is set to 1 (input capture function). Timer RC I/O Control Register 1(1) b7 b6 b5 b4 b3 b2 b1 b0 Symbol Address TRCIOR1 0125h Bit Symbol Bit Name IOC0 TRCGRC control bits IOC1 TRCGRC mode select bit(2) IOC2 After Reset 10001000b Function Function varies according to the operating mode (function). 0 : Output compare function 1 : Input capture function Nothing is assigned. If necessary, set to 0. When read, the content is 1. IOD0 IOD1 TRCGRD control bits Function varies according to the operating mode (function). RW RW TRCGRD mode select bit(3) 0 : Output compare function 1 : Input capture function RW -- (b7) Nothing is assigned. If necessary, set to 0. When read, the content is 1. NOTES: 1. The TRCIOR1 register is enabled in timer mode. It is disabled in modes PWM and PWM2. 2. When the BFC bit in the TRCMR register is set to 1 (buffer register of TRCGRA register), set the IOC2 bit in the TRCIOR1 register to the same value as the IOA2 bit in the TRCIOR0 register. 3. When the BFD bit in the TRCMR register is set to 1 (buffer register of TRCGRB register), set the IOD2 bit in the TRCIOR1 register to the same value as the IOB2 bit in the TRCIOR0 register. Registers TRCIOR0 and TRCIOR1 Rev.1.10 Dec 21, 2007 REJ09B0406-0110 RW -- (b3) IOD2 Figure 16.38 RW RW RW Page 185 of 450 -- -- R8C/2K Group, R8C/2L Group 16.3.3 16. Timers Common Items for Multiple Modes 16.3.3.1 Count Source The method of selecting the count source is common to all modes. Table 16.14 lists the Count Source Selection, and Figure 16.39 shows a Count Source Block Diagram. Table 16.14 Count Source Selection Count Source f1, f2, f4, f8, f32 fOCO40M Selection Method Count source selected using bits TCK2 to TCK0 in TRCCR1 register FRA00 bit in FRA0 register set to 1 (high-speed on-chip oscillator on) and bits TCK2 to TCK0 in TRCCR1 register are set to 110b (fOCO40M) External signal input Bits TCK2 to TCK0 in TRCCR1 register are set to 101b (count source is rising edge to TRCCLK pin of external clock) and PD5_0 bit in PD5 register is set to 0 (input mode) TCK2 to TCK0 f1 = 000b = 001b f2 = 010b f4 Count source = 011b f8 TRC register = 100b f32 = 101b TRCCLK = 110b fOCO40M TCK2 to TCK0: Bits in TRCCR1 register Figure 16.39 Count Source Block Diagram The pulse width of the external clock input to the TRCCLK pin should be three cycles or more of the timer RC operation clock (see Table 16.11 Timer RC Operation Clock). To select fOCO40M as the count source, set the FRA00 bit in the FRA0 register set to 1 (high-speed on-chip oscillator on), and then set bits TCK2 to TCK0 in the TRCCR1 register to 110b (fOCO40M). Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 186 of 450 R8C/2K Group, R8C/2L Group 16.3.3.2 16. Timers Buffer Operation Bits BFC and BFD in the TRCMR register are used to select the TRCGRC or TRCGRD register as the buffer register for the TRCGRA or TRCGRB register. * Buffer register for TRCGRA register: TRCGRC register * Buffer register for TRCGRB register: TRCGRD register Buffer operation differs depending on the mode. Table 16.15 lists the Buffer Operation in Each Mode, Figure 16.40 shows the Buffer Operation for Input Capture Function, and Figure 16.41 shows the Buffer Operation for Output Compare Function. Table 16.15 Buffer Operation in Each Mode Function, Mode Input capture function Transfer Timing Input capture signal input Transfer Destination Register Contents of TRCGRA (TRCGRB) register are transferred to buffer register Contents of buffer register are transferred to TRCGRA (TRCGRB) register Contents of buffer register (TRCGRD) are transferred to TRCGRB register Output compare function Compare match between TRC register and TRCGRA (TRCGRB) PWM mode register PWM2 mode * Compare match between TRC register and TRCGRA register * TRCTRG pin trigger input TRCIOA input (input capture signal) TRCGRC register TRCGRA register TRC TRCIOA input TRC register n n-1 n+1 Transfer TRCGRA register m n Transfer TRCGRC register (buffer) m The above applies under the following conditions: * The BFC bit in the TRCMR register is set to 1 (the TRCGRC register functions as the buffer register for the TRCGRA register). * Bits IOA2 to IOA0 in the TRCIOR0 register are set to 100b (input capture at the rising edge). Figure 16.40 Buffer Operation for Input Capture Function Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 187 of 450 R8C/2K Group, R8C/2L Group 16. Timers Compare match signal TRCGRC register TRC register TRCGRA register TRCGRA register Comparator m m-1 TRC m+1 m n Transfer TRCGRC register (buffer) n TRCIOA output The above applies under the following conditions: * The BFC bit in the TRCMR register is set to 1 (the TRCGRC register functions as the buffer register for the TRCGRA register). * Bits IOA2 to IOA0 in the TRCIOR0 register are set to 001b ("L" output at compare match). Figure 16.41 Buffer Operation for Output Compare Function Make the following settings in timer mode. * To use the TRCGRC register as the buffer register for the TRCGRA register: Set the IOC2 bit in the TRCIOR1 register to the same value as the IOA2 bit in the TRCIOR0 register. * To use the TRCGRD register as the buffer register for the TRCGRB register: Set the IOD2 bit in the TRCIOR1 register to the same value as the IOB2 bit in the TRCIOR0 register. The output compare function, PWM mode, or PWM2 mode, and the TRCGRC or TRCGRD register is functioning as a buffer register, the IMFC bit or IMFD bit in the TRCSR register is set to 1 when a compare match with the TRC register occurs. The input capture function and the TRCGRC register or TRCGRD register is functioning as a buffer register, the IMFC bit or IMFD bit in the TRCSR register is set to 1 at the input edge of a signal input to the TRCIOC pin or TRCIOD pin. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 188 of 450 R8C/2K Group, R8C/2L Group 16.3.3.3 16. Timers Digital Filter The input to TRCTRG or TRCIOj (j = A, B, C, or D) is sampled, and the level is considered to be determined when three matches occur. The digital filter function and sampling clock are selected using the TRCDF register. Figure 16.42 shows a Block Diagram of Digital Filter. TCK2 to TCK0 f1 f2 f4 f8 f32 TRCCLK DFCK1 to DFCK0 = 000b = 00b f32 = 001b = 01b f8 = 010b = 10b f1 = 011b = 11b Count source = 100b IOA2 to IOA0 IOB2 to IOB0 IOC2 to IOC0 IOD2 to IOD0 (or TCEG1 to TCEG0) = 101b = 110b fOCO40M Sampling clock DFj (or DFTRG) C TRCIOj input signal (or TRCTRG input signal) D C Q Latch C D Q Latch D 1 C Q Latch D Q Match detect circuit Edge detect circuit Latch 0 Timer RC operation clock f1 or fOCO40M C D Q Latch Clock cycle selected by TCK2 to TCK0 (or DFCK1 to DFCK0) Sampling clock TRCIOj input signal (or TRCTRG input signal) Three matches occur and a signal change is confirmed. Input signal after passing through digital filter Maximum signal transmission delay is five sampling clock pulses. If fewer than three matches occur, the matches are treated as noise and no transmission is performed. j = A, B, C, or D TCK0 to TCK2: Bits in TRCCR1 register DFTRG, DFCK0 to DFCK1, DFj: Bits in TRCDF register IOA0 to IOA2, IOB0 to IOB2: Bits in TRCIOR0 register IOC0 to IOC2, IOD0 to IOD2: Bits in TRCIOR1 register TCEG1 to TCEG0: Bits in TRCCR2 register Figure 16.42 Block Diagram of Digital Filter Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 189 of 450 R8C/2K Group, R8C/2L Group 16.3.3.4 16. Timers Forced Cutoff of Pulse Output When using the timer mode's output compare function, the PWM mode, or the PWM2 mode, pulse output from the TRCIOj (j = A, B, C, or D) output pin can be forcibly cut off and the TRCIOj pin set to function as a programmable I/O port by means of input to the INT0 pin. A pin used for output by the timer mode's output compare function, the PWM mode, or the PWM2 mode can be set to function as the timer RC output pin by setting the Ej bit in the TRCOER register to 0 (timer RC output enabled). If "L" is input to the INT0 pin while the PTO bit in the TRCOER register is set to 1 (pulse output forced cutoff signal input INT0 enabled), bits EA, EB, EC, and ED in the TRCOER register are all set to 1 (timer RC output disabled, TRCIOj output pin functions as the programmable I/O port). When one or two cycles of the timer RC operation clock after "L" input to the INT0 pin (refer to Table 16.11 Timer RC Operation Clock) has elapsed, the TRCIOj output pin becomes a programmable I/O port. Make the following settings to use this function. * Set the pin state following forced cutoff of pulse output (high impedance (input), "L" output, or "H" output). (Refer to 7. Programmable I/O Ports.) * Set the INT0EN bit to 1 (INT0 input enabled) and the INT0PL bit to 0 (one edge) in the INTEN register. * Set the PD4_5 bit in the PD4 register to 0 (input mode). * Select the INT0 digital filter by means of bits INT0F1 to INT0F0 in the INTF register. * Set the PTO bit in the TRCOER register to 1 (pulse output forced cutoff signal input INT0 enabled). The IR bit in the INT0IC register is set to 1 (interrupt request) in accordance with the setting of the POL bit and a change in the INT0 pin input (refer to 12.6 Notes on Interrupts). For details on interrupts, refer to 12. Interrupts. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 190 of 450 R8C/2K Group, R8C/2L Group 16. Timers EA bit write value INT0 input EA bit D Q S Timer RC output data TRCIOA Port P1_1 output data PTO bit Port P1_1 input data EB bit write value EB bit D Q S Timer RC output data TRCIOB Port P1_2 output data Port P1_2 input data EC bit write value EC bit D Q S Timer RC output data TRCIOC Port P3_4 output data Port P3_4 input data ED bit write value ED bit D Q S Timer RC output data Port P3_5 output data Port P3_5 input data EA, EB, EC, ED, PTO: Bits in TRCOER register Figure 16.43 Forced Cutoff of Pulse Output Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 191 of 450 TRCIOD R8C/2K Group, R8C/2L Group 16.3.4 16. Timers Timer Mode (Input Capture Function) This function measures the width or period of an external signal. An external signal input to the TRCIOj (j = A, B, C, or D) pin acts as a trigger for transferring the contents of the TRC register (counter) to the TRCGRj register (input capture). The input capture function, or any other mode or function, can be selected for each individual pin. The TRCGRA register can also select fOCO128 signal as input-capture trigger input. Table 16.16 lists the Specifications of Input Capture Function, Figure 16.44 shows a Block Diagram of Input Capture Function, Figures 16.45 and 16.46 show the registers associated with the input capture function, Table 16.17 lists the Functions of TRCGRj Register when Using Input Capture Function, and Figure 16.47 shows an Operating Example of Input Capture Function. Table 16.16 Specifications of Input Capture Function Item Count source Count operation Count period Count start condition Count stop condition Interrupt request generation timing TRCIOA, TRCIOB, TRCIOC, and TRCIOD pin functions INT0 pin function Read from timer Write to timer Select functions Specification f1, f2, f4, f8, f32, fOCO40M, or external signal (rising edge) input to TRCCLK pin Increment 1/fk x 65,536 fk: Count source frequency 1 (count starts) is written to the TSTART bit in the TRCMR register. 0 (count stops) is written to the TSTART bit in the TRCMR register. The TRC register retains a value before count stops. * Input capture (valid edge of TRCIOj input or fOCO128 signal edge) * The TRC register overflows. Programmable I/O port or input capture input (selectable individually by pin) Programmable I/O port or INT0 interrupt input The count value can be read by reading TRC register. The TRC register can be written to. * Input capture input pin select One or more of pins TRCIOA, TRCIOB, TRCIOC, and TRCIOD * Input capture input valid edge selected Rising edge, falling edge, or both rising and falling edges * Buffer operation (Refer to 16.3.3.2 Buffer Operation.) * Digital filter (Refer to 16.3.3.3 Digital Filter.) * Input-capture trigger selected fOCO128 can be selected for input-capture trigger input of the TRCGRA register. j = A, B, C, or D Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 192 of 450 R8C/2K Group, R8C/2L Group fOCO Divided by 128 16. Timers fOCO128 IOA3 = 0 Input capture signal(3) TRCIOA IOA3 = 1 (Note 1) TRCGRA register TRC register TRCGRC register TRCIOC Input capture signal Input capture signal TRCIOB (Note 2) TRCGRB register TRCGRD register TRCIOD Input capture signal IOA3: Bit in TRCIOR0 register NOTES: 1. The BFC bit in the TRCMR register is set to 1 (TRCGRC register functions as the buffer register for the TRCGRA register) 2. The BFD bit in the TRCMR register is set to 1 (TRCGRD register functions as the buffer register for the TRCGRB register) 3. The trigger input of the TRCGRA register can select the TRCIOA pin input or fOCO128 signal. Figure 16.44 Block Diagram of Input Capture Function Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 193 of 450 R8C/2K Group, R8C/2L Group 16. Timers Timer RC I/O Control Register 0 b7 b6 b5 b4 b3 b2 b1 b0 1 1 Symbol TRCIOR0 Bit Symbol Address 0124h Bit Name TRCGRA control bits IOA1 IOA3 RW TRCGRA input capture input sw itch bit(3) 0 : fOCO128 signal 1 : TRCIOA pin input RW TRCGRB control bits b5 b4 0 0 : Input capture to the TRCGRB register at the rising edge 0 1 : Input capture to the TRCGRB register at the falling edge 1 0 : Input capture to the TRCGRB register at both edges 1 1 : Do not set. TRCGRB mode select bit(2) Set to 1 (input capture) in the input capture function. Nothing is assigned. If necessary, set to 0. When read, the content is 1. NOTES: 1. When the BFC bit in the TRCMR register is set to 1 (buffer register of TRCGRA register), set the IOC2 bit in the TRCIOR1 register to the same value as the IOA2 bit in the TRCIOR0 register. 2. When the BFD bit in the TRCMR register is set to 1 (buffer register of TRCGRB register), set the IOD2 bit in the TRCIOR1 register to the same value as the IOB2 bit in the TRCIOR0 register. 3. The IOA3 bit is enabled w hen the IOA2 bit is set to 1 (input capture function). Figure 16.45 TRCIOR0 Register for Input Capture Function Rev.1.10 Dec 21, 2007 REJ09B0406-0110 RW Set to 1 (input capture) in the input capture function. IOB1 -- (b7) RW TRCGRA mode select bit(1) IOB0 IOB2 RW b1 b0 0 0 : Input capture to the TRCGRA register at the rising edge 0 1 : Input capture to the TRCGRA register at the falling edge 1 0 : Input capture to the TRCGRA register at both edges 1 1 : Do not set. IOA0 IOA2 After Reset 10001000b Function Page 194 of 450 RW RW RW -- R8C/2K Group, R8C/2L Group 16. Timers Timer RC I/O Control Register 1 b7 b6 b5 b4 b3 b2 b1 b0 1 1 Symbol TRCIOR1 Bit Symbol Address 0125h Bit Name TRCGRC control bits After Reset 10001000b Function 0 0 : Input capture to the TRCGRC register at the rising edge 0 1 : Input capture to the TRCGRC register at the falling edge 1 0 : Input capture to the TRCGRC register at both edges 1 1 : Do not set. IOC0 IOC1 IOC2 -- (b3) TRCGRC mode select bit(1) RW RW RW -- b5 b4 0 0 : Input capture to the TRCGRD register at the rising edge 0 1 : Input capture to the TRCGRD register at the falling edge 1 0 : Input capture to the TRCGRD register at both edges 1 1 : Do not set. IOD0 IOD1 -- (b7) Set to 1 (input capture) in the input capture function. Nothing is assigned. If necessary, set to 0. When read, the content is 1. TRCGRD control bits IOD2 RW b1 b0 TRCGRD mode select bit(2) Set to 1 (input capture) in the input capture function. Nothing is assigned. If necessary, set to 0. When read, the content is 1. RW RW RW -- NOTES: 1. When the BFC bit in the TRCMR register is set to 1 (buffer register of TRCGRA register), set the IOC2 bit in the TRCIOR1 register to the same value as the IOA2 bit in the TRCIOR0 register. 2. When the BFD bit in the TRCMR register is set to 1 (buffer register of TRCGRB register), set the IOD2 bit in the TRCIOR1 register to the same value as the IOB2 bit in the TRCIOR0 register. Figure 16.46 Table 16.17 TRCIOR1 Register for Input Capture Function Functions of TRCGRj Register when Using Input Capture Function Register TRCGRA TRCGRB TRCGRC TRCGRD TRCGRC TRCGRD Setting - BFC = 0 BFD = 0 BFC = 1 BFD = 1 Input Capture Input Pin General register. Can be used to read the TRC register value TRCIOA at input capture. TRCIOB General register. Can be used to read the TRC register value TRCIOC at input capture. TRCIOD Buffer registers. Can be used to hold transferred value from TRCIOA the general register. (Refer to 16.3.3.2 Buffer Operation.) TRCIOB Register Function j = A, B, C, or D BFC, BFD: Bits in TRCMR register Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 195 of 450 R8C/2K Group, R8C/2L Group 16. Timers TRCCLK input count source TRC register count value FFFFh 0006h 0003h 0000h TSTART bit in TRCMR register 1 0 65536 TRCIOA input TRCGRA register 0006h Transfer TRCGRC register 0003h Transfer 0006h IMFA bit in TRCSR register 1 OVF bit in TRCSR register 1 0 Set to 0 by a program 0 The above applies under the following conditions: * Bits TCK2 to TCK0 in the TRCCR1 register are set to 101b (the count source is TRCCLK input). * Bits IOA2 to IOA0 in the TRCIORA register are set to 101b (input capture at the falling edge of the TRCIOA input). * The BFC bit in the TRCMR register is set to 1 (the TRCGRC register functions as the buffer register for the TRCGRA register). Figure 16.47 Operating Example of Input Capture Function Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 196 of 450 R8C/2K Group, R8C/2L Group 16.3.5 16. Timers Timer Mode (Output Compare Function) This function detects when the contents of the TRC register (counter) and the TRCGRj register (j = A, B, C, or D) match (compare match). When a match occurs a signal is output from the TRCIOj pin at a given level. The output compare function, or other mode or function, can be selected for each individual pin. Table 16.18 lists the Specifications of Output Compare Function, Figure 16.48 shows a Block Diagram of Output Compare Function, Figures 16.49 to 16.51 show the registers associated with the output compare function, Table 16.19 lists the Functions of TRCGRj Register when Using Output Compare Function, and Figure 16.52 shows an Operating Example of Output Compare Function. Table 16.18 Specifications of Output Compare Function Item Count source Count operation Count period Waveform output timing Count start condition Count stop condition Interrupt request generation timing TRCIOA, TRCIOB, TRCIOC, and TRCIOD pin functions Specification f1, f2, f4, f8, f32, fOCO40M, or external signal (rising edge) input to TRCCLK pin Increment * The CCLR bit in the TRCCR1 register is set to 0 (free running operation): 1/fk x 65,536 fk: Count source frequency * The CCLR bit in the TRCCR1 register is set to 1 (TRC register set to 0000h at TRCGRA compare match): 1/fk x (n + 1) n: TRCGRA register setting value Compare match 1 (count starts) is written to the TSTART bit in the TRCMR register. 0 (count stops) is written to the TSTART bit in the TRCMR register. The output compare output pin retains output level before count stops, the TRC register retains a value before count stops. * Compare match (contents of registers TRC and TRCGRj match) * The TRC register overflows. Programmable I/O port or output compare output (selectable individually by pin) INT0 pin function Programmable I/O port, pulse output forced cutoff signal input, or INT0 interrupt input Read from timer Write to timer Select functions The count value can be read by reading the TRC register. The TRC register can be written to. * Output compare output pin selected One or more of pins TRCIOA, TRCIOB, TRCIOC, and TRCIOD * Compare match output level select "L" output, "H" output, or toggle output * Initial output level select Sets output level for period from count start to compare match * Timing for clearing the TRC register to 0000h Overflow or compare match with the TRCGRA register * Buffer operation (Refer to 16.3.3.2 Buffer Operation.) * Pulse output forced cutoff signal input (Refer to 16.3.3.4 Forced Cutoff of Pulse Output.) * Can be used as an internal timer by disabling timer RC output j = A, B, C, or D Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 197 of 450 R8C/2K Group, R8C/2L Group 16. Timers TRC TRCIOA TRCIOC TRCIOB TRCIOD Figure 16.48 Output control Output control Output control Output control Compare match signal TRCGRA Comparator TRCGRC Comparator TRCGRB Comparator TRCGRD Compare match signal Compare match signal Compare match signal Block Diagram of Output Compare Function Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Comparator Page 198 of 450 R8C/2K Group, R8C/2L Group 16. Timers Timer RC I/O Control Register 0 b7 b6 b5 b4 b3 b2 b1 b0 0 1 0 Symbol TRCIOR0 Bit Symbol Address 0124h Bit Name TRCGRA control bits IOA1 IOA3 TRCGRA mode select bit(1) Set to 0 (output compare) in the output compare function. TRCGRA input capture input sw itch bit Set to 1. TRCGRB control bits b5 b4 0 0 : Disable pin output by compare match (TRCIOB pin functions as the programmable I/O port) 0 1 : "L" output by compare match in the TRCGRB register 1 0 : "H" output by compare match in the TRCGRB register 1 1 : Toggle output by compare match in the TRCGRB register IOB0 IOB1 IOB2 -- (b7) TRCGRB mode select bit(2) Set to 0 (output compare) in the output compare function. Nothing is assigned. If necessary, set to 0. When read, the content is 1. NOTES: 1. When the BFC bit in the TRCMR register is set to 1 (buffer register of TRCGRA register), set the IOC2 bit in the TRCIOR1 register to the same value as the IOA2 bit in the TRCIOR0 register. 2. When the BFD bit in the TRCMR register is set to 1 (buffer register of TRCGRB register), set the IOD2 bit in the TRCIOR1 register to the same value as the IOB2 bit in the TRCIOR0 register. Figure 16.49 TRCIOR0 Register for Output Compare Function Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 199 of 450 RW b1 b0 0 0 : Disable pin output by compare match (TRCIOA pin functions as the programmable I/O port) 0 1 : "L" output by compare match in the TRCGRA register 1 0 : "H" output by compare match in the TRCGRA register 1 1 : Toggle output by compare match in the TRCGRA register IOA0 IOA2 After Reset 10001000b Function RW RW RW RW RW RW RW -- R8C/2K Group, R8C/2L Group 16. Timers Timer RC I/O Control Register 1 b7 b6 b5 b4 b3 b2 b1 b0 0 0 Symbol TRCIOR1 Bit Symbol Address 0125h Bit Name TRCGRC control bits IOC1 -- (b3) TRCGRC mode select bit(1) IOD1 -- (b7) TRCGRD mode select bit(2) Set to 0 (output compare) in the output compare function. Nothing is assigned. If necessary, set to 0. When read, the content is 1. NOTES: 1. When the BFC bit in the TRCMR register is set to 1 (buffer register of TRCGRA register), set the IOC2 bit in the TRCIOR1 register to the same value as the IOA2 bit in the TRCIOR0 register. 2. When the BFD bit in the TRCMR register is set to 1 (buffer register of TRCGRB register), set the IOD2 bit in the TRCIOR1 register to the same value as the IOB2 bit in the TRCIOR0 register. Figure 16.50 TRCIOR1 Register for Output Compare Function Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 200 of 450 RW RW RW -- b5 b4 0 0 : Disable pin output by compare match 0 1 : "L" output by compare match in the TRCGRD register 1 0 : "H" output by compare match in the TRCGRD register 1 1 : Toggle output by compare match in the TRCGRD register IOD0 IOD2 Set to 0 (output compare) in the output compare function. Nothing is assigned. If necessary, set to 0. When read, the content is 1. TRCGRD control bits RW b1 b0 0 0 : Disable pin output by compare match 0 1 : "L" output by compare match in the TRCGRC register 1 0 : "H" output by compare match in the TRCGRC register 1 1 : Toggle output by compare match in the TRCGRC register IOC0 IOC2 After Reset 10001000b Function RW RW RW -- R8C/2K Group, R8C/2L Group 16. Timers Timer RC Control Register 1 b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRCCR1 Bit Symbol TOA TOB TOC TOD Address 0121h Bit Name TRCIOA output level select bit(1, 2) After Reset 00h Function 0 : Initial output "L" 1 : Initial output "H" RW RW TRCIOB output level select bit(1, 2) RW TRCIOC output level select bit(1, 2) RW TRCIOD output level select bit(1, 2) Count source select bits (1) RW b6 b5 b4 0 0 0 0 1 1 1 1 TCK0 TCK1 TCK2 TRC counter clear select bit CCLR 0 0 1 1 0 0 1 1 0 : f1 1 : f2 0 : f4 1 : f8 0 : f32 1 : TRCCLK input rising edge 0 : fOCO40M 1 : Do not set. RW 0 : Disable clear (free-running operation) 1 : Clear by compare match in the TRCGRA register RW RW RW NOTES: 1. Set to these bits w hen the TSTART bit in the TRCMR register is set to 0 (count stops). 2. If the pin function is set for w aveform output (refer to Tables 7.10 to 7.13 and Tables 7.29 to 7.32), the initial output level is output w hen the TRCCR1 register is set. Figure 16.51 Table 16.19 TRCCR1 Register for Output Compare Function Functions of TRCGRj Register when Using Output Compare Function Register TRCGRA TRCGRB TRCGRC TRCGRD TRCGRC TRCGRD Setting Register Function - General register. Write a compare value to one of these registers. BFC = 0 BFD = 0 BFC = 1 BFD = 1 General register. Write a compare value to one of these registers. Buffer register. Write the next compare value to one of these registers. (Refer to 16.3.3.2 Buffer Operation.) j = A, B, C, or D BFC, BFD: Bits in TRCMR register Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 201 of 450 Output Compare Output Pin TRCIOA TRCIOB TRCIOC TRCIOD TRCIOA TRCIOB R8C/2K Group, R8C/2L Group 16. Timers Count source TRC register value m n p Count restarts Count stops TSTART bit in TRCMR register 1 0 m+1 m+1 Output level held TRCIOA output Output inverted at compare match Initial output "L" IMFA bit in TRCSR register 1 0 Set to 0 by a program Output level held n+1 TRCIOB output "H" output at compare match Initial output "L" IMFB bit in TRCSR register 1 0 Set to 0 by a program P+1 Output level held "L" output at compare match TRCIOC output Initial output "H" IMFC bit in TRCSR register 1 0 Set to 0 by a program m: TRCGRA register setting value n: TRCGRB register setting value p: TRCGRC register setting value The above applies under the following conditions: * Bits BFC and BFD in the TRCMR register are set to 0 (TRCGRC and TRCGRD do not operate as buffers). * Bits EA, EB, and EC in the TRCOER register are set to 0 (output from TRCIOA, TRCIOB, and TRCIOC enabled). * The CCLR bit in the TRCCR1 register is set to 1 (set the TRC register to 0000h by TRCGRA compare match). * In the TRCCR1 register, bits TOA and TOB are set to 0 ("L" initial output until compare match) and the TOC bit is set to 1 ("H" initial output until compare match). * Bits IOA2 to IOA0 in the TRCIOR0 register are set to 011b (TRCIOA output inverted at TRCGRA compare match). * Bits IOB2 to IOB0 in the TRCIOR0 register are set to 010b ("H" TRCIOB output at TRCGRB compare match). * Bits IOC2 to IOC2 in the TRCIOR1 register are set to 001b ("L" TRCIOC output at TRCGRC compare match). Figure 16.52 Operating Example of Output Compare Function Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 202 of 450 R8C/2K Group, R8C/2L Group 16.3.6 16. Timers PWM Mode This mode outputs PWM waveforms. A maximum of three PWM waveforms with the same period are output. The PWM mode, or the timer mode, can be selected for each individual pin. (However, since the TRCGRA register is used when using any pin for the PWM mode, the TRCGRA register cannot be used for the timer mode.) Table 16.20 lists the Specifications of PWM Mode, Figure 16.53 shows a Block Diagram of PWM Mode, Figure 16.54 shows the registers associated with the PWM mode, Table 16.21 lists the Functions of TRCGRj Register in PWM Mode, and Figures 16.55 and 16.56 show Operating Examples of PWM Mode. Table 16.20 Specifications of PWM Mode Item Specification f1, f2, f4, f8, f32, fOCO40M, or external signal (rising edge) input to TRCCLK pin Increment PWM period: 1/fk x (m + 1) Active level width: 1/fk x (m - n) Inactive width: 1/fk x (n + 1) fk: Count source frequency m: TRCGRA register setting value n: TRCGRj register setting value Count source Count operation PWM waveform m+1 n+1 Count start condition Count stop condition Interrupt request generation timing TRCIOA pin function TRCIOB, TRCIOC, and TRCIOD pin functions INT0 pin function Read from timer Write to timer Select functions ("L" is active level) 1 (count starts) is written to the TSTART bit in the TRCMR register. 0 (count stops) is written to the TSTART bit in the TRCMR register. PWM output pin retains output level before count stops, TRC register retains value before count stops. * Compare match (contents of registers TRC and TRCGRh match) * The TRC register overflows. Programmable I/O port Programmable I/O port or PWM output (selectable individually by pin) Programmable I/O port, pulse output forced cutoff signal input, or INT0 interrupt input The count value can be read by reading the TRC register. The TRC register can be written to. * One to three pins selectable as PWM output pins per channel One or more of pins TRCIOB, TRCIOC, and TRCIOD * Active level selectable by individual pin * Buffer operation (Refer to 16.3.3.2 Buffer Operation.) * Pulse output forced cutoff signal input (Refer to 16.3.3.4 Forced Cutoff of Pulse Output.) j = B, C, or D h = A, B, C, or D Rev.1.10 Dec 21, 2007 REJ09B0406-0110 m-n Page 203 of 450 R8C/2K Group, R8C/2L Group 16. Timers TRC Compare match signal Comparator TRCIOB TRCGRA Compare match signal (Note 1) Output control TRCIOC Comparator TRCGRB Comparator TRCGRC Compare match signal TRCIOD (Note 2) Compare match signal Comparator TRCGRD NOTES: 1. The BFC bit in the TRCMR register is set to 1 (TRCGRC register functions as the buffer register for the TRCGRA register) 2. The BFD bit in the TRCMR register is set to 1 (TRCGRD register functions as the buffer register for the TRCGRB register) Figure 16.53 Block Diagram of PWM Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 204 of 450 R8C/2K Group, R8C/2L Group 16. Timers Timer RC Control Register 1 b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRCCR1 Bit Symbol TOA Address 0121h Bit Name TRCIOA output level select bit(1) After Reset 00h Function Disabled in PWM mode TRCIOB output level select bit(1, 2) 0 : Active level "H" (Initial output "L" "H" output by compare match in the TRCGRj register "L" output by compare match in the TRCGRA register 1 : Active level "L" (Initial output "H" "L" output by compare match in the TRCGRj register "H" output by compare match in the TRCGRA register TOB TRCIOC output level select bit(1, 2) TOC TRCIOD output level select bit(1, 2) TOD Count source select bits (1) TCK1 TCK2 TRC counter clear select bit CCLR RW RW RW RW b6 b5 b4 0 0 0 0 1 1 1 1 TCK0 RW 0 0 1 1 0 0 1 1 0 : f1 1 : f2 0 : f4 1 : f8 0 : f32 1 : TRCCLK input rising edge 0 : fOCO40M 1 : Do not set. 0 : Disable clear (free-running operation) 1 : Clear by compare match in the TRCGRA register RW RW RW RW j = B, C or D NOTES: 1. Set to these bits w hen the TSTART bit in the TRCMR register is set to 0 (count stops). 2. If the pin function is set for w aveform output (refer to Tables 7.12 to 7.13 and Tables 7.29 to 7.32), the initial output level is output w hen the TRCCR1 register is set. Figure 16.54 Table 16.21 TRCCR1 Register in PWM Mode Functions of TRCGRj Register in PWM Mode Register TRCGRA TRCGRB TRCGRC TRCGRD TRCGRC Setting - - BFC = 0 BFD = 0 BFC = 1 TRCGRD BFD = 1 Register Function General register. Set the PWM period. General register. Set the PWM output change point. General register. Set the PWM output change point. Buffer register. Set the next PWM period. (Refer to 16.3.3.2 Buffer Operation.) Buffer register. Set the next PWM output change point. (Refer to 16.3.3.2 Buffer Operation.) PWM Output Pin - TRCIOB TRCIOC TRCIOD - TRCIOB j = A, B, C, or D BFC, BFD: Bits in TRCMR register NOTE: 1. The output level does not change even when a compare match occurs if the TRCGRA register value (PWM period) is the same as the TRCGRB, TRCGRC, or TRCGRD register value. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 205 of 450 R8C/2K Group, R8C/2L Group 16. Timers Count source TRC register value m n p q m+1 n+1 Active level is "H" TRCIOB output m-n Inactive level is "L" p+1 m-p "L" initial output until compare match TRCIOC output q+1 m-q Active level is "L" TRCIOD output "H" initial output until compare match IMFA bit in TRCSR register 1 IMFB bit in TRCSR register 1 IMFC bit in TRCSR register 1 IMFD bit in TRCSR register 1 0 Set to 0 by a program Set to 0 by a program 0 0 Set to 0 by a program Set to 0 by a program 0 m: TRCGRA register setting value n: TRCGRB register setting value p: TRCGRC register setting value q: TRCGRD register setting value The above applies under the following conditions: * Bits BFC and BFD in the TRCMR register are set to 0 (registers TRCGRC and TRCGRD do not operate as buffers). * Bits EB, EC, and ED in the TRCOER register are set to 0 (output from TRCIOB, TRCIOC, and TRCIOD enabled). * In the TRCCR1 register, bits TOB and TOC are set to 0 (active level is "H") and the TOD bit is set to 1 (active level is "L"). Figure 16.55 Operating Example of PWM Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 206 of 450 R8C/2K Group, R8C/2L Group 16. Timers TRC register value p m q n 0000h TSTART bit in TRCMR register 1 TRCIOB output does not switch to "L" because no compare match with the TRCGRB register has occurred 0 Duty 0% TRCIOB output TRCGRB register n q p (p>m) Rewritten by a program IMFA bit in TRCSR register 1 IMFB bit in TRCSR register 1 0 Set to 0 by a program Set to 0 by a program 0 TRC register value m p n 0000h TSTART bit in TRCMR register 1 If compare matches occur simultaneously with registers TRCGRA and TRCGRB, the compare match with the TRCGRB register has priority. TRCIOB output switches to "L". (In other words, no change). 0 Duty 100% TRCIOB output TRCIOB output switches to "L" at compare match with the TRCGRB register. (In other words, no change). n TRCGRB register IMFA bit in TRCSR register 1 IMFB bit in TRCSR register 1 m p Rewritten by a program 0 Set to 0 by a program Set to 0 by a program 0 m: TRCGRA register setting value The above applies under the following conditions: * The EB bit in the TRCOER register is set to 0 (output from TRCIOB enabled). * The TOB bit in the TRCCR1 register is set to 1 (active level is "L"). Figure 16.56 Operating Example of PWM Mode (Duty 0% and Duty 100%) Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 207 of 450 R8C/2K Group, R8C/2L Group 16.3.7 16. Timers PWM2 Mode This mode outputs a single PWM waveform. After a given wait duration has elapsed following the trigger, the pin output switches to active level. Then, after a given duration, the output switches back to inactive level. Furthermore, the counter stops at the same time the output returns to inactive level, making it possible to use PWM2 mode to output a programmable wait one-shot waveform. Since timer RC uses multiple general registers in PWM2 mode, other modes cannot be used in conjunction with it. Figure 16.57 shows a Block Diagram of PWM2 Mode, Table 16.22 lists the Specifications of PWM2 Mode, Figure 16.58 shows the register associated with PWM2 mode, Table 16.23 lists the Functions of TRCGRj Register in PWM2 Mode, and Figures 16.59 to 16.61 show Operating Examples of PWM2 Mode. Trigger signal Compare match signal TRCTRG TRCIOB Input control Count clear signal TRC (Note 1) Comparator TRCGRA Comparator TRCGRB Comparator TRCGRC TRCGRD register Output control NOTE: 1. The BFD bit in the TRCMR register is set to 1 (the TRCGRD register functions as the buffer register for the TRCGRB register). Figure 16.57 Block Diagram of PWM2 Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 208 of 450 R8C/2K Group, R8C/2L Group Table 16.22 16. Timers Specifications of PWM2 Mode Item Count source Count operation PWM waveform Specification f1, f2, f4, f8, f32, fOCO40M, or external signal (rising edge) input to TRCCLK pin Increment TRC register PWM period: 1/fk x (m + 1) (no TRCTRG input) Active level width: 1/fk x (n - p) Wait time from count start or trigger: 1/fk x (p + 1) fk: Count source frequency m: TRCGRA register setting value n: TRCGRB register setting value p: TRCGRC register setting value TRCTRG input m+1 n+1 n+1 p+1 p+1 TRCIOB output n-p n-p (TRCTRG: Rising edge, active level is "H") Count start conditions Count stop conditions * Bits TCEG1 to TCEG0 in the TRCCR2 register are set to 00b (TRCTRG trigger disabled) or the CSEL bit in the TRCCR2 register is set to 0 (count continues). 1 (count starts) is written to the TSTART bit in the TRCMR register. * Bits TCEG1 to TCEG0 in the TRCCR2 register are set to 01b, 10b, or 11b (TRCTRG trigger enabled) and the TSTART bit in the TRCMR register is set to 1 (count starts). A trigger is input to the TRCTRG pin * 0 (count stops) is written to the TSTART bit in the TRCMR register while the CSEL bit in the TRCCR2 register is set to 0 or 1. The TRCIOB pin outputs the initial level in accordance with the value of the TOB bit in the TRCCR1 register. The TRC register retains the value before count stops. * The count stops due to a compare match with TRCGRA while the CSEL bit in the TRCCR2 register is set to 1 The TRCIOB pin outputs the initial level. The TRC register retains the value before count stops if the CCLR bit in the TRCCR1 register is set to 0. The TRC register is set to 0000h if the CCLR bit in the TRCCR1 register is set to 1. * Compare match (contents of TRC and TRCGRj registers match) * The TRC register overflows Programmable I/O port or TRCTRG input Interrupt request generation timing TRCIOA/TRCTRG pin function TRCIOB pin function PWM output TRCIOC and TRCIOD pin Programmable I/O port functions INT0 pin function Read from timer Write to timer Select functions Programmable I/O port, pulse output forced cutoff signal input, or INT0 interrupt input The count value can be read by reading the TRC register. The TRC register can be written to. * External trigger and valid edge selected The edge or edges of the signal input to the TRCTRG pin can be used as the PWM output trigger: rising edge, falling edge, or both rising and falling edges * Buffer operation (Refer to 16.3.3.2 Buffer Operation.) * Pulse output forced cutoff signal input (Refer to 16.3.3.4 Forced Cutoff of Pulse Output.) * Digital filter (Refer to 16.3.3.3 Digital Filter.) j = A, B, or C Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 209 of 450 R8C/2K Group, R8C/2L Group 16. Timers Timer RC Control Register 1 b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRCCR1 Bit Symbol TOA Address 0121h Bit Name TRCIOA output level select bit(1) After Reset 00h Function Disabled in the PWM2 mode TRCIOB output level select bit(1, 2) 0 : Active level "H" (Initial output "L" "H" output by compare match in the TRCGRC register "L" output by compare match in the TRCGRB register 1 : Active level "L" (Initial output "H" "L" output by compare match in the TRCGRC register "H" output by compare match in the TRCGRB register TOB TOC TOD TRCIOC output level select bit(1) Disabled in the PWM2 mode TRCIOD output level select bit(1) Count source select bits (1) TCK1 TCK2 TRC counter clear select bit CCLR RW RW RW RW b6 b5 b4 0 0 0 0 1 1 1 1 TCK0 RW 0 0 1 1 0 0 1 1 0 : f1 1 : f2 0 : f4 1 : f8 0 : f32 1 : TRCCLK input rising edge 0 : fOCO40M 1 : Do not set. 0 : Disable clear (free-running operation) 1 : Clear by compare match in the TRCGRA register RW RW RW RW NOTES: 1. Set to these bits w hen the TSTART bit in the TRCMR register is set to 0 (count stops). 2. If the pin function is set for w aveform output (refer to Tables 7.12 and 7.13), the initial output level is output w hen the TRCCR1 register is set. Figure 16.58 Table 16.23 TRCCR1 Register in PWM2 Mode Functions of TRCGRj Register in PWM2 Mode Register TRCGRA TRCGRB TRCGRC Setting - - BFC = 0 TRCGRD TRCGRD BFD = 0 BFD = 1 Register Function PWM2 Output Pin General register. Set the PWM period. TRCIOB pin General register. Set the PWM output change point. General register. Set the PWM output change point (wait time after trigger). (Not used in PWM2 mode) - Buffer register. Set the next PWM output change point. (Refer to TRCIOB pin 16.3.3.2 Buffer Operation.) j = A, B, C, or D BFC, BFD: Bits in TRCMR register NOTE: 1. Do not set the TRCGRB and TRCGRC registers to the same value. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 210 of 450 R8C/2K Group, R8C/2L Group 16. Timers Count source TRC register value FFFFh TRC register cleared at TRCGRA register compare match m n Previous value held if the TSTART bit is set to 0 Set to 0000h by a program p 0000h TSTART bit in TRCMR register Count stops because the CSEL bit is set to 1 1 0 Set to 1 by a program CSEL bit in TRCCR2 register TSTART bit is set to 0 1 0 m+1 n+1 p+1 "H" output at TRCGRC register compare match p+1 Return to initial output if the TSTART bit is set to 0 "L" initial output TRCIOB output "L" output at TRCGRB register compare match No change No change "H" output at TRCGRC register compare match IMFA bit in TRCSR register 1 IMFB bit in TRCSR register 1 IMFC bit in TRCSR register 1 0 Set to 0 by a program 0 Set to 0 by a program Set to 0 by a program 0 TRCGRB register n Transfer TRCGRD register n Transfer Next data Transfer from buffer register to general register m: TRCGRA register setting value n: TRCGRB register setting value p: TRCGRC register setting value The above applies under the following conditions: * The TOB bit in the TRCCR1 register is set to 0 (initial level is "L", "H" output at compare match with the TRCGRC register, "L" output at compare match with the TRCGRB register). * Bits TCEG1 and TCEG0 in the TRCCR2 register are set to 00b (TRCTRG trigger input disabled). Figure 16.59 Operating Example of PWM2 Mode (TRCTRG Trigger Input Disabled) Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 211 of 450 R8C/2K Group, R8C/2L Group 16. Timers Count source TRC register value TRC register cleared at TRCGRA register compare match FFFFh m TRC register (counter) cleared at TRCTRG pin trigger input Previous value held if the TSTART bit is set to 0 n Set to 0000h by a program p 0000h TRCTRG input Count starts at TRCTRG pin trigger input Count starts TSTART bit is set to 1 TSTART bit in TRCMR register 1 CSEL bit in TRCCR2 register 1 Count stops because the CSEL bit is set to 1 Changed by a program The TSTART bit is set to 0 0 Set to 1 by a program 0 m+1 n+1 n+1 p+1 p+1 "H" output at TRCGRC register compare match "L" output at TRCGRB register compare match "L" initial output TRCIOB output IMFA bit in TRCSR register 1 IMFB bit in TRCSR register 1 IMFC bit in TRCSR register 1 TRCGRB register p+1 Inactive level so TRCTRG input is enabled Return to initial value if the TSTART bit is set to 0 Active level so TRCTRG input is disabled 0 Set to 0 by a program 0 Set to 0 by a program Set to 0 by a program Set to 0 by a program 0 n n n Transfer TRCGRD register Transfer n Transfer from buffer register to general register n Transfer Transfer Next data Transfer from buffer register to general register m: TRCGRA register setting value n: TRCGRB register setting value p: TRCGRC register setting value The above applies under the following conditions: * The TOB bit in the TRCCR1 register is set to 0 (initial level is "L", "H" output at compare match with the TRCGRC register, "L" output at compare match with the TRCGRB register). * Bits TCEG1 and TCEG0 in the TRCCR2 register are set to 11b (trigger at both rising and falling edges of TRCTRG input). Figure 16.60 Operating Example of PWM2 Mode (TRCTRG Trigger Input Enabled) Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 212 of 450 R8C/2K Group, R8C/2L Group 16. Timers * TRCGRB register setting value greater than TRCGRA register setting value TRC register value * TRCGRC register setting value greater than TRCGRA register setting value TRC register value n p m m n p 0000h TSTART bit in TRCMR register 0000h 1 TSTART bit in TRCMR register 0 n+1 m+1 m+1 TRCIOB output "H" output at TRCGRC register compare match 1 IMFB bit in TRCSR register 1 IMFC bit in TRCSR register 0 p+1 No compare match with TRCGRB register, so "H" output continues IMFA bit in TRCSR register 1 "L" initial output 0 0 1 No compare match with TRCGRC register, so "L" output continues TRCIOB output IMFA bit in TRCSR register 1 IMFB bit in TRCSR register 1 IMFC bit in TRCSR register 1 Set to 0 by a program 0 "L" output at TRCGRB register compare match with no change. "L" initial output 0 0 0 m: TRCGRA register setting value n: TRCGRB register setting value p: TRCGRC register setting value The above applies under the following conditions: * The TOB bit in the TRCCR1 register is set to 0 (initial level is "L", "H" output at compare match with the TRCGRC register, "L" output at compare match with the TRCGRB register). * Bits TCEG1 and TCEG0 in the TRCCR2 register are set to 00b (TRCTRG trigger input disabled). Figure 16.61 Operating Example of PWM2 Mode (Duty 0% and Duty 100%) Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 213 of 450 R8C/2K Group, R8C/2L Group 16.3.8 16. Timers Timer RC Interrupt Timer RC generates a timer RC interrupt request from five sources. The timer RC interrupt uses the single TRCIC register (bits IR and ILVL0 to ILVL2) and a single vector. Table 16.24 lists the Registers Associated with Timer RC Interrupt, and Figure 16.62 is a Timer RC Interrupt Block Diagram. Table 16.24 Registers Associated with Timer RC Interrupt Timer RC Status Register TRCSR Timer RC Interrupt Enable Register TRCIER Timer RC Interrupt Control Register TRCIC IMFA bit IMIEA bit Timer RC interrupt request (IR bit in TRCIC register) IMFB bit IMIEB bit IMFC bit IMIEC bit IMFD bit IMIED bit OVF bit OVIE bit IMFA, IMFB, IMFC, IMFD, OVF: Bits in TRCSR register IMIEA, IMIEB, IMIEC, IMIED, OVIE: Bits in TRCIER register Figure 16.62 Timer RC Interrupt Block Diagram Like other maskable interrupts, the timer RC interrupt is controlled by the combination of the I flag, IR bit, bits ILVL0 to ILVL2, and IPL. However, it differs from other maskable interrupts in the following respects because a single interrupt source (timer RC interrupt) is generated from multiple interrupt request sources. * The IR bit in the TRCIC register is set to 1 (interrupt requested) when a bit in the TRCSR register is set to 1 and the corresponding bit in the TRCIER register is also set to 1 (interrupt enabled). * The IR bit is set to 0 (no interrupt request) when the bit in the TRCSR register or the corresponding bit in the TRCIER register is set to 0, or both are set to 0. In other words, the interrupt request is not maintained if the IR bit is once set to 1 but the interrupt is not acknowledged. * If after the IR bit is set to 1 another interrupt source is triggered, the IR bit remains set to 1 and does not change. * If multiple bits in the TRCIER register are set to 1, use the TRCSR register to determine the source of the interrupt request. * The bits in the TRCSR register are not automatically set to 0 when an interrupt is acknowledged. Set them to 0 within the interrupt routine. Refer to Figure 16.32 TRCSR Register, for the procedure for setting these bits to 0. Refer to Figure 16.31 TRCIER Register, for details of the TRCIER register. Refer to 12.1.6 Interrupt Control, for details of the TRCIC register and 12.1.5.2 Relocatable Vector Tables, for information on interrupt vectors. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 214 of 450 R8C/2K Group, R8C/2L Group 16.3.9 16. Timers Notes on Timer RC 16.3.9.1 TRC Register * The following note applies when the CCLR bit in the TRCCR1 register is set to 1 (clear TRC register at compare match with TRCGRA register). When using a program to write a value to the TRC register while the TSTART bit in the TRCMR register is set to 1 (count starts), ensure that the write does not overlap with the timing with which the TRC register is set to 0000h. If the timing of the write to the TRC register and the setting of the TRC register to 0000h coincide, the write value will not be written to the TRC register and the TRC register will be set to 0000h. * Reading from the TRC register immediately after writing to it can result in the value previous to the write being read out. To prevent this, execute the JMP.B instruction between the read and the write instructions. Program Example MOV.W #XXXXh, TRC ;Write JMP.B L1 ;JMP.B instruction L1: MOV.W TRC,DATA ;Read 16.3.9.2 TRCSR Register Reading from the TRCSR register immediately after writing to it can result in the value previous to the write being read out. To prevent this, execute the JMP.B instruction between the read and the write instructions. Program Example MOV.B #XXh, TRCSR ;Write JMP.B L1 ;JMP.B instruction L1: MOV.B TRCSR,DATA ;Read 16.3.9.3 Count Source Switching * Stop the count before switching the count source. Switching procedure (1) Set the TSTART bit in the TRCMR register to 0 (count stops). (2) Change the settings of bits TCK2 to TCK0 in the TRCCR1 register. * After switching the count source from fOCO40M to another clock, allow a minimum of two cycles of f1 to elapse after changing the clock setting before stopping fOCO40M. Switching procedure (1) Set the TSTART bit in the TRCMR register to 0 (count stops). (2) Change the settings of bits TCK2 to TCK0 in the TRCCR1 register. (3) Wait for a minimum of two cycles of f1. (4) Set the FRA00 bit in the FRA0 register to 0 (high-speed on-chip oscillator off). 16.3.9.4 Input Capture Function * The pulse width of the input capture signal should be three cycles or more of the timer RC operation clock (refer to Table 16.11 Timer RC Operation Clock). * The value of the TRC register is transferred to the TRCGRj register one or two cycles of the timer RC operation clock after the input capture signal is input to the TRCIOj (j = A, B, C, or D) pin (when the digital filter function is not used). 16.3.9.5 TRCMR Register in PWM2 Mode When the CSEL bit in the TRCCR2 register is set to 1 (count stops at compare match with the TRCGRA register), do not set the TRCMR register at compare match timing of registers TRC and TRCGRA. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 215 of 450 R8C/2K Group, R8C/2L Group 16.4 16. Timers Timer RD Timer RD has 2 16-bit timers (channels 0 and 1). Each channel has 4 I/O pins. The operation clock of timer RD is f1 or fOCO40M. Table 16.25 lists the Timer RD Operation Clocks. Table 16.25 Timer RD Operation Clocks Condition Operation Clock of Timer RD The count source is f1, f2, f4, f8, f32, or TRDCLK input f1 (bits TCK2 to TCK0 in registers TRDCR0 and TRDCR1 are set to a value from 000b to 101b). The count source is fOCO40M (bits TCK2 to TCK0 in registers TRDCR0 and TRDCR1 are set to 110b). fOCO40M Figure 16.63 shows a Block Diagram of Timer RD. Timer RD has 5 modes: * Timer mode - Input capture function Transfer the counter value to a register with an external signal as the trigger - Output compare function Detect register value matches with a counter (Pin output can be changed at detection) The following 4 modes use the output compare function. * PWM mode Output pulse of any width continuously * Reset synchronous PWM mode Output three-phase waveforms (6) without sawtooth wave modulation and dead time * Complementary PWM mode Output three-phase waveforms (6) with triangular wave modulation and dead time * PWM3 mode Output PWM waveforms (2) with a fixed period In the input capture function, output compare function, and PWM mode, channels 0 and 1 have the equivalent functions, and functions or modes can be selected individually for each pin. Also, a combination of these functions and modes can be used in 1 channel. In reset synchronous PWM mode, complementary PWM mode, and PWM3 mode, a waveform is output with a combination of counters and registers in channels 0 and 1. Tables 16.26 to 16.34 list the Pin Functions of timer RD. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 216 of 450 R8C/2K Group, R8C/2L Group Table 16.26 Pin Functions TRDIOA0/TRDCLK(P2_0) Register TRDOER1 Bit EA0 Setting value 16. Timers TRDFCR TRDIORA0 Function PWM3 STCLK CMD1, CMD0 IOA3 IOA2_IOA0 0 0 0 00b X XXXb 0 1 0 00b 1 001b, 01Xb 1 0 00b X 1XXb Timer mode trigger input (input capture function)(1) 1 1 XXb X 000b External clock input (TRDCLK)(1) X Other than above PWM3 mode waveform output Timer mode waveform output (output compare function) I/O port X: can be 0 or 1, no change in outcome NOTE: 1. Set the PD2_0 bit in the PD2 register to 0 (input mode) at timer mode trigger input (input capture function) and external clock input (TRDCLK). Table 16.27 Pin Functions TRDIOB0(P2_1) Register TRDOER1 Bit EB0 Setting value TRDFCR TRDPMR TRDIORA0 PWM3 CMD1, CMD0 PWMB0 IOB2_IOB0 1Xb X XXXb Complementary PWM mode waveform output Function 0 X 0 X 01b X XXXb Reset synchronous PWM mode waveform output 0 0 00b X XXXb PWM3 mode waveform output 0 1 00b 1 XXXb PWM mode waveform output 0 1 00b 0 001b, 01Xb X 1 00b 0 1XXb Other than above Timer mode waveform output (output compare function) Timer mode trigger input (input capture function)(1) I/O port X: can be 0 or 1, no change in outcome NOTE: 1. Set the PD2_1 bit in the PD2 register to 0 (input mode) at timer mode trigger input (input capture function). Table 16.28 Pin Functions TRDIOC0(P2_2) Register TRDOER1 TRDFCR TRDPMR TRDIORC0 Bit EC0 PWM3 CMD1, CMD0 PWMC0 IOC2_IOC0 1Xb X XXXb Setting value Function 0 X 0 X 01b X XXXb Reset synchronous PWM mode waveform output 0 1 00b 1 XXXb PWM mode waveform output 0 1 00b 0 001b, 01Xb X 1 00b 0 1XXb Other than above Complementary PWM mode waveform output Timer mode waveform output (output compare function) Timer mode trigger input (input capture function)(1) I/O port X: can be 0 or 1, no change in outcome NOTE: 1. Set the PD2_2 bit in the PD2 register to 0 (input mode) at timer mode trigger input (input capture function). Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 217 of 450 R8C/2K Group, R8C/2L Group Table 16.29 16. Timers Pin Functions TRDIOD0(P2_3) Register TRDOER1 TRDFCR TRDPMR TRDIORC0 Bit ED0 PWM3 CMD1, CMD0 PWMD0 IOD2_IOD0 1Xb X XXXb Setting value Function 0 X 0 X 01b X XXXb Reset synchronous PWM mode waveform output 0 1 00b 1 XXXb PWM mode waveform output 0 1 00b 0 001b, 01Xb X 1 00b 0 1XXb Other than above Complementary PWM mode waveform output Timer mode waveform output (output compare function) Timer mode trigger input (input capture function)(1) I/O port X: can be 0 or 1, no change in outcome NOTE: 1. Set the PD2_3 bit in the PD2 register to 0 (input mode) at timer mode trigger input (input capture function). Table 16.30 Pin Functions TRDIOA1(P2_4) Register TRDOER1 TRDFCR TRDIORA1 Bit EA1 PWM3 CMD1, CMD0 IOA2_IOA0 Setting value Function 0 X 1Xb XXXb Complementary PWM mode waveform output 0 X 01b XXXb Reset synchronous PWM mode waveform output 0 1 00b 001b, 01Xb X 1 00b 1XXb Other than above Timer mode waveform output (output compare function) Timer mode trigger input (input capture function)(1) I/O port X: can be 0 or 1, no change in outcome NOTE: 1. Set the PD2_4 bit in the PD2 register to 0 (input mode) at timer mode trigger input (input capture function). Table 16.31 Pin Functions TRDIOB1(P2_5) Register TRDOER1 TRDFCR TRDPMR TRDIORA1 Bit EB1 PWM3 CMD1, CMD0 PWMB1 IOB2_IOB0 1Xb X XXXb Setting value Function 0 X 0 X 01b X XXXb Reset synchronous PWM mode waveform output 0 1 00b 1 XXXb PWM mode waveform output 0 1 00b 0 001b, 01Xb X 1 00b 0 1XXb Other than above Complementary PWM mode waveform output Timer mode waveform output (output compare function) Timer mode trigger input (input capture function)(1) I/O port X: can be 0 or 1, no change in outcome NOTE: 1. Set the PD2_5 bit in the PD2 register to 0 (input mode) at timer mode trigger input (input capture function). Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 218 of 450 R8C/2K Group, R8C/2L Group Table 16.32 16. Timers Pin Functions TRDIOC1(P2_6) Register TRDOER1 TRDFCR TRDPMR TRDIORC1 Bit EC1 PWM3 CMD1, CMD0 PWMC1 IOC2_IOC0 1Xb X XXXb Setting value Function 0 X 0 X 01b X XXXb Reset synchronous PWM mode waveform output 0 1 00b 1 XXXb PWM mode waveform output 0 1 00b 0 001b, 01Xb X 1 00b 0 1XXb Other than above Complementary PWM mode waveform output Timer mode waveform output (output compare function) Timer mode trigger input (input capture function)(1) I/O port X: can be 0 or 1, no change in outcome NOTE: 1. Set the PD2_6 bit in the PD2 register to 0 (input mode) at timer mode trigger input (input capture function). Table 16.33 Pin Functions TRDIOD1(P2_7) Register TRDOER1 TRDFCR TRDPMR TRDIORC1 Bit ED1 PWM3 CMD1, CMD0 PWMD1 IOD2_IOD0 Setting value Function 0 X 1Xb X XXXb Complementary PWM mode waveform output 0 X 01b X XXXb Reset synchronous PWM mode waveform output 0 1 00b 1 XXXb PWM mode waveform output 0 1 00b 0 001b, 01Xb X 1 00b 0 1XXb Other than above Timer mode waveform output (output compare function) Timer mode trigger input (input capture function)(1) I/O port X: can be 0 or 1, no change in outcome NOTE: 1. Set the PD2_7 bit in the PD2 register to 0 (input mode) at timer mode trigger input (input capture function). Table 16.34 Pin Functions INT0(P4_5) Register TRDOER2 Bit PTO Setting value 1 Rev.1.10 Dec 21, 2007 REJ09B0406-0110 INTEN PD4 INT0PL INT0EN PD4_5 0 1 0 Other than above Page 219 of 450 Function Pulse output forced cutoff signal input I/O port or INT0 interrupt input R8C/2K Group, R8C/2L Group 16. Timers f1, f2, f4, f8, f32, fOCO40M Channel i TRDi register TRDGRAi register TRDGRBi register TRDGRCi register INT0 Count source select circuit TRDGRDi register TRDDFi register Data bus TRDCRi register TRDIOA0/TRDCLK TRDIOB0 Timer RD control circuit TRDIOC0 TRDIOD0 TRDIORAi register TRDIOA1 TRDIORCi register TRDIOB1 TRDSRi register TRDIOC1 TRDIERi register TRDIOD1 TRDPOCRi register TRDSTR register TRDMR register TRDPMR register TRDFCR register TRDOER1 register TRDOER2 register TRDOCR register i = 0 or 1 Figure 16.63 Block Diagram of Timer RD Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 220 of 450 Channel 0 interrupt request Channel 1 interrupt request A/D trigger R8C/2K Group, R8C/2L Group 16.4.1 16. Timers Count Sources The count source selection method is the same in all modes. However, in PWM3 mode, the external clock cannot be selected. Table 16.35 Count Source Selection Count Source Selection f1, f2, f4, f8, f32 The count source is selected by bits TCK2 to TCK0 in the TRDCRi register. fOCO40M(1) The FRA00 bit in the FRA0 register is set to 1 (high-speed on-chip oscillator frequency). Bits TCK2 to TCK0 in the TRDCRi register is set to 110b (fOCO40M). External signal input to TRDCLK pin The STCLK bit in the TRDFCR register is set to 1 (external clock input enabled). Bits TCK2 to TCK0 in the TRDCRi register are set to 101b (count source: external clock). The valid edge is selected by bits CKEG1 to CKEG0 in the TRDCRi register. The PD2_0 bit in the PD2 register is set to 0 (input mode). i = 0 or 1 NOTE: 1. The count source fOCO40M can be used with VCC = 3.0 to 5.5 V. TCK2 to TCK0 f1 = 000b = 001b f2 = 010b f4 Count source = 011b f8 TRDi register = 100b f32 = 110b fOCO40M = 101b STCLK = 1 TRDCLK/ TRDIOA0 CKEG1 to CKEG0 Valid edge selected STCLK = 0 TRDIOA0 I/O or programmable I/O port TCK2 to TCK0, CKEG1 to CKEG0: Bits in TRDCRi register STCLK: Bit in TRDFCR register Figure 16.64 Block Diagram of Count Source Set the pulse width of the external clock which inputs to the TRDCLK pin to 3 cycles or above of the operation clock of timer RD (refer to Table 16.25 Timer RD Operation Clocks). When selecting fOCO40M for the count source, set the FRA00 bit in the FRA0 register to 1 (high-speed onchip oscillator on) before setting bits TCK2 to TCK0 in the TRDCRi register (i = 0 or 1) to 110b (fOCO40M). Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 221 of 450 R8C/2K Group, R8C/2L Group 16.4.2 16. Timers Buffer Operation The TRDGRCi (i = 0 or 1) register can be used as the buffer register of the TRDGRAi register, and the TRDGRDi register can be used as the buffer register of the TRDGRBi register by means of bits BFCi and BFDi in the TRDMR register. * TRDGRAi buffer register: TRDGRCi register * TRDGRBi buffer register: TRDGRDi register Buffer operation depends on the mode. Table 16.36 lists the Buffer Operation in Each Mode. Table 16.36 Buffer Operation in Each Mode Function and Mode Transfer Timing Transfer Register Input capture function Input capture signal input Transfer content in TRDGRAi (TRDGRBi) register to buffer register Output compare function Compare match with TRDi register and TRDGRAi (TRDGRBi) register Transfer content in buffer register to TRDGRAi (TRDGRBi) register Reset synchronous PWM Compare match withTRD0 register mode and TRDGRA0 register Transfer content in buffer register to TRDGRAi (TRDGRBi) register PWM mode Complementary PWM mode * Compare match with TRD0 register Transfer content in buffer register to and TRDGRA0 register registers TRDGRB0, TRDGRA1, and * TRD1 register underflow TRDGRB1 PWM3 mode Compare match with TRD0 register and TRDGRA0 register Transfer content in buffer register to registers TRDGRA0, TRDGRB0, TRDGRA1, and TRDGRB1 i = 0 or 1 TRDIOAi input (input capture signal) TRDGRCi register (buffer) TRDGRAi register TRDi TRDIOAi input TRDi register n n-1 n+1 Transfer TRDGRAi register m n Transfer TRDGRCi register (buffer) m i = 0 or 1 The above applies under the following conditions: * The BFCi bit in the TRDMR register is set to 1 (the TRDGRCi register is used as the buffer register of the TRDGRAi register). * Bits IOA2 to IOA0 in the TRDIORAi register are set to 100b (input capture at the falling edge). Figure 16.65 Buffer Operation in Input Capture Function Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 222 of 450 R8C/2K Group, R8C/2L Group 16. Timers Compare match signal TRDGRCi register (buffer) TRDi register TRDGRAi register m m-1 TRDGRAi register Comparator TRDi m+1 m n Transfer TRDGRCi register (buffer) n TRDIOAi output i = 0 or 1 The above applies under the following conditions: * BFCi bit in the TRDMR register is set to 1 (the TRDGRCi register is used as the buffer register of the TRDGRAi register). * Bits IOA2 to IOA0 in the TRDIORAi register are set to 001b ("L" output by the compare match). Figure 16.66 Buffer Operation in Output Compare Function Perform the following for the timer mode (input capture and output compare functions). When using the TRDGRCi (i = 0 or 1) register as the buffer register of the TRDGRAi register * Set the IOC3 bit in the TRDIORCi register to 1 (general register or buffer register). * Set the IOC2 bit in the TRDIORCi register to the same value as the IOA2 bit in the TRDIORAi register. When using the TRDGRDi register as the buffer register of the TRDGRBi register * Set the IOD3 bit in the TRDIORDi register to 1 (general register or buffer register). * Set the IOD2 bit in the TRDIORCi register to the same value as the IOB2 bit in the TRDIORAi register. Bits IMFC and IMFD in the TRDSRi register are set to 1 at the input edge of the TRDIOCi pin when also using registers TRDGRCi and TRDGRDi as the buffer register in the input capture function. When also using registers TRDGRCi and TRDGRDi as buffer registers for the output compare function, reset synchronous PWM mode, complementary PWM mode, and PWM3 mode, bits IMFC and IMFD in the TRDSRi register are set to 1 by a compare match with the TRDi register. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 223 of 450 R8C/2K Group, R8C/2L Group 16.4.3 16. Timers Synchronous Operation The TRD1 register is synchronized with the TRD0 register. * Synchronous preset When the SYNC bit in the TRDMR register is set to 1 (synchronous operation), the data is written to both the TRD0 and TRD1 registers after writing to the TRDi register. * Synchronous clear When the SYNC bit in the TRDMR register is set to 1 and bits CCLR2 to CCLR0 in the TRDCRi register are set to 011b (synchronous clear), the TRD0 register is set to 0000h at the same time as the TRD1 register is set to 0000h. Also, when the SYNC bit in the TRDMR register is set to 1 and bits CCLR2 to CCLR0 in the TRDCRi register are set to 011b (synchronous clear), the TRD1 register is set to 0000h at the same time as the TRD0 register is set to 0000h. TRDIOA0 input Set to 0000h by input capture Value in TRD0 register n n writing n is set Value in TRD1 register n is set n Set to 0000h with TRD0 register The above applies under the following conditions: * The SYNC bit in the TRDMR register is set to 1 (synchronous operation). * Bits CCLR2 to CCLR0 in the TRDCR0 register are set to 001b (set the TRD0 register to 0000h in input capture). Bits CCLR2 to CCLR0 in the TRDCR1 register are set to 011b (set the TRD1 register to 0000h synchronizing with the TRD0 register). * Bits IOA2 to IOA0 in the TRDIORA0 register are set to 100b. * Bits CMD1 to CMD0 in the TRDFCR register are set to 00b. (Input capture at the rising edge of the TRDIOA0 input) The PWM 3 bit in the TRDFCR register is set to 1. Figure 16.67 Synchronous Operation Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 224 of 450 R8C/2K Group, R8C/2L Group 16.4.4 16. Timers Pulse Output Forced Cutoff In the output compare function, PWM mode, reset synchronous PWM mode, complementary PWM mode, and PWM3 mode, the TRDIOji (i = 0 or 1, j = either A, B, C, or D) output pin can be forcibly set to a programmable I/O port by the INT0 pin input, and pulse output can be cut off. The pins used for output in these functions or modes can function as the output pin of timer RD when the applicable bit in the TRDOER1 register is set to 0 (enable timer RD output). When the PTO bit in the TRDOER2 register to 1 (INT0 of pulse output forced cutoff signal input enabled), all bits in the TRDOER1 register are set to 1 (disable timer RD output, the TRDIOji output pin is used as the programmable I/O port) after "L" is applied to the INT0 pin. The TRDIOji output pin is set to the programmable I/O port after "L" is applied to the INT0 pin and waiting for 1 to 2 cycles of the timer RD operation clock (refer to Table 16.25 Timer RD Operation Clocks). Set as below when using this function: * Set the pin status (high impedance, "L" or "H" output) to pulse output forced cutoff by registers P2 and PD2. * Set the INT0EN bit in the INTEN register to 1 (enable INT0 input) and the INT0PL bit to 0 (one edge). * Set the PD4_5 bit in the PD4 register to 0 (input mode). * Set the INT0 digital filter by bits INT0F1 to INT0F0 in the INTF register. * Set the PTO bit in the TRDOER2 register to 1 (enable pulse output forced cutoff signal input INT0). According to the selection of the POL bit in the INT0IC register and change of the INT0 pin input, the IR bit in the INT0IC register is set to 1 (interrupt request). Refer to 12. Interrupts for details of interrupts. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 225 of 450 R8C/2K Group, R8C/2L Group 16. Timers EA0 bit writing value INT0 input EA0 bit D Q S Timer RD output data TRDIOA0 Port P2_0 output data PTO bit Port P2_0 input data EB0 bit writing value EB0 bit D Q S Timer RD output data TRDIOB0 Port P2_1 output data Port P2_1 input data EC0 bit writing value EC0 bit D Q S Timer RD output data TRDIOC0 Port P2_2 output data Port P2_2 input data ED0 bit writing value ED0 bit D Q S Timer RD output data TRDIOD0 Port P2_3 output data Port P2_3 input data EA1 bit writing value EA1 bit D Q S Timer RD output data TRDIOA1 Port P2_4 output data Port P2_4 input data EB1 bit writing value EB1 bit D Q S Timer RD output data TRDIOB1 Port P2_5 output data Port P2_5 input data EC1 bit writing value EC1 bit D Q S Timer RD output data TRDIOC1 Port P2_6 output data Port P2_6 input data ED1 bit writing value ED1 bit D Q S Timer RD output data Port P2_7 output data Port P2_7 input data PTO: Bit in TRDOER2 register EA0, EB0, EC0, ED0, EA1, EB1, EC1, ED1: Bits in TRDOER1 register Figure 16.68 Pulse Output Forced Cutoff Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 226 of 450 TRDIOD1 R8C/2K Group, R8C/2L Group 16.4.5 16. Timers Input Capture Function The input capture function measures the external signal width and period. The content of the TRDi register (counter) is transferred to the TRDGRji register as a trigger of the TRDIOji (i = 0 or 1, j = either A, B, C, or D) pin external signal (input capture). Since this function is enabled with a combination of the TRDIOji pin and TRDGRji register, the input capture function, or any other mode or function, can be selected for each individual pin. The TRDGRA0 register can also select fOCO128 signal as input-capture trigger input. Figure 16.69 shows a Block Diagram of Input Capture Function, Table 16.37 lists the Input Capture Function Specifications. Figures 16.70 to 16.80 show the Registers Associated with Input Capture Function, and Figure 16.81 shows an Operating Example of Input Capture Function. Input capture signal TRDIOAi(3) (Note 1) TRDGRAi register TRDi register TRDGRCi register TRDIOCi Input capture signal Input capture signal TRDIOBi (Note 2) TRDGRBi register fOCO TRDIOA0 Divided by 128 fOCO128 IOA3 = 0 Input capture signal IOA3 = 1 TRDGRDi register TRDIODi Input capture signal NOTE 3: The trigger input of the TRDGRA0 register can select the TRDIOA0 pin input or fOCO128 signal. i = 0 or 1 NOTE 1: When the BFCi bit in the TRDMR register is set to 1 (the TRDGRCi register is used as the buffer register of the TRDGRAi register). NOTE 2: When the BFDi bit in the TRDMR register is set to 1 (the TRDGRDi register is used as the buffer register of the TRDGRBi register). Figure 16.69 Block Diagram of Input Capture Function Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 227 of 450 R8C/2K Group, R8C/2L Group Table 16.37 16. Timers Input Capture Function Specifications Item Specification Count sources f1, f2, f4, f8, f32, fOCO40M External signal input to the TRDCLK pin (valid edge selected by a program) Count operations Increment Count period When bits CCLR2 to CCLR0 in the TRDCRi register are set to 000b (free-running operation). 1/fk x 65536 fk: Frequency of count source Count start condition 1 (count starts) is written to the TSTARTi bit in the TRDSTR register. Count stop condition 0 (count stops) is written to the TSTARTi bit in the TRDSTR register when the CSELi bit in the TRDSTR register is set to 1. Interrupt request generation timing * Input capture (valid edge of TRDIOji input or fOCO128 signal edge) * TRDi register overflows TRDIOA0 pin function Programmable I/O port, input-capture input, or TRDCLK (external clock) input TRDIOB0, TRDIOC0, TRDIOD0, TRDIOA1 to TRDIOD1 pin functions Programmable I/O port, or input-capture input (selectable by pin) INT0 pin function Programmable I/O port or INT0 interrupt input Read from timer The count value can be read by reading the TRDi register. Write to timer * When the SYNC bit in the TRDMR register is set to 0 (channels 0 and 1 operate independently). Data can be written to the TRDi register. * When the SYNC bit in the TRDMR register is set to 1 (channels 0 and 1 operate synchronously). Data can be written to both the TRD0 and TRD1 registers by writing to the TRDi register. Select functions * Input-capture input pin selected Either 1 pin or multiple pins among TRDIOAi, TRDIOBi, TRDIOCi, or TRDIODi. * Input-capture input valid edge selected The rising edge, falling edge, or both the rising and falling edges * The timing when the TRDi register is set to 0000h At overflow or input capture * Buffer operation (Refer to 16.4.2 Buffer Operation.) * Synchronous operation (Refer to 16.4.3 Synchronous Operation.) * Digital filter The TRDIOji input is sampled, and when the sampled input level match as 3 times, the level is determined. * Input-capture trigger selected fOCO128 can be selected for input-capture trigger input of the TRDGRA0 register. i = 0 or 1, j = either A, B, C, or D Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 228 of 450 R8C/2K Group, R8C/2L Group 16. Timers Timer RD Start Register(1) b7 b6 b5 b4 b3 b2 b1 b0 1 1 Symbol TRDSTR Bit Symbol TSTART0 TSTART1 CSEL0 CSEL1 -- (b7-b4) Address 0137h Bit Name TRD0 count start flag After Reset 11111100b Function RW 0 : Count stops 1 : Count starts RW TRD1 count start flag 0 : Count stops 1 : Count starts RW TRD0 count operation select bit Set to 1 in the input capture function. TRD1 count operation select bit Set to 1 in the input capture function. Nothing is assigned. If necessary, set to 0. When read, the content is 1. RW RW -- NOTE: 1. Set the TRDSTR register using the MOV instruction (do not use the bit handling instruction). Refer to 16.4.12.1 TRDSTR Register of Notes on Tim er RD. Timer RD Mode Register b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRDMR Bit Symbol Address 0138h Bit Name Timer RD synchronous bit SYNC RW -- BFC0 TRDGRC0 register function select 0 : General register bit 1 : Buffer register of TRDGRA0 register RW BFD0 TRDGRD0 register function select 0 : General register bit 1 : Buffer register of TRDGRB0 register RW BFC1 TRDGRC1 register function select 0 : General register bit 1 : Buffer register of TRDGRA1 register RW BFD1 TRDGRD1 register function select 0 : General register bit 1 : Buffer register of TRDGRB1 register RW Registers TRDSTR and TRDMR in Input Capture Function Rev.1.10 Dec 21, 2007 REJ09B0406-0110 RW Nothing is assigned. If necessary, set to 0. When read, the content is 1. -- (b3-b1) Figure 16.70 After Reset 00001110b Function 0 : Registers TRD0 and TRD1 operate independently 1 : Registers TRD0 and TRD1 operate synchronously Page 229 of 450 R8C/2K Group, R8C/2L Group 16. Timers Timer RD PWM Mode Register b7 b6 b5 b4 b3 b2 b1 b0 0 0 0 0 0 0 Symbol TRDPMR Bit Symbol PWMB0 PWMC0 PWMD0 -- (b3) PWMB1 PWMC1 PWMD1 -- (b7) Figure 16.71 Address 0139h Bit Name PWM mode of TRDIOB0 select bit After Reset 10001000b Function Set to 0 (timer mode) in the input capture function. RW PWM mode of TRDIOC0 select bit Set to 0 (timer mode) in the input capture function. RW PWM mode of TRDIOD0 select bit Set to 0 (timer mode) in the input capture function. RW Nothing is assigned. If necessary, set to 0. When read, the content is 1. -- PWM mode of TRDIOB1 select bit Set to 0 (timer mode) in the input capture function. RW PWM mode of TRDIOC1 select bit Set to 0 (timer mode) in the input capture function. RW PWM mode of TRDIOD1 select bit Set to 0 (timer mode) in the input capture function. RW Nothing is assigned. If necessary, set to 0. When read, the content is 1. TRDPMR Register in Input Capture Function Rev.1.10 Dec 21, 2007 REJ09B0406-0110 RW Page 230 of 450 -- R8C/2K Group, R8C/2L Group 16. Timers Timer RD Function Control Register b7 b6 b5 b4 b3 b2 b1 b0 1 0 0 Symbol TRDFCR Bit Symbol CMD0 Address 013Ah Bit Name Combination mode select bits (1) After Reset 10000000b Function Set to 00b (timer mode, PWM mode, or PWM3 mode) in the input capture function. CMD1 RW OLS0 RW OLS1 Counter-phase output level select bit This bit is disabled in the input capture (in reset synchronous PWM mode or function. complementary PWM mode) RW ADTRG A/D trigger enable bit (in complementary PWM mode) This bit is disabled in the input capture function. RW ADEG A/D trigger edge select bit (in complementary PWM mode) This bit is disabled in the input capture function. RW External clock input select bit 0 : External clock input disabled 1 : External clock input enabled RW Set this bit to 1 (other than PWM3 mode) in the input capture function. RW (2) PWM3 PWM3 mode select bit NOTES: 1. Set bits CMD1 to CMD0 w hen both the TSTART0 and TSTART1 bits are set to 0 (count stops). 2. When bits CMD1 to CMD0 are set to 00b (timer mode, PWM mode, or PWM3 mode), the setting of the PWM3 bit is enabled. TRDFCR Register in Input Capture Function Rev.1.10 Dec 21, 2007 REJ09B0406-0110 RW Normal-phase output level select bit This bit is disabled in the input capture (in reset synchronous PWM mode or function. complementary PWM mode) STCLK Figure 16.72 RW Page 231 of 450 R8C/2K Group, R8C/2L Group 16. Timers Timer RD Digital Filter Function Select Register i (i = 0 or 1) b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRDDF0 TRDDF1 Bit Symbol Address 013Eh 013Fh Bit Name TRDIOA pin digital filter function select bit Function 0 : Function is not used 1 : Function is used DFB TRDIOB pin digital filter function select bit 0 : Function is not used 1 : Function is used RW DFC TRDIOC pin digital filter function select bit 0 : Function is not used 1 : Function is used RW DFD TRDIOD pin digital filter function select bit 0 : Function is not used 1 : Function is used RW DFA -- (b5-b4) DFCK0 Nothing is assigned. If necessary, set to 0. When read, the content is 0. Clock select bits for digital filter function DFCK1 Figure 16.73 After Reset 00h 00h Page 232 of 450 RW -- b7 b6 0 0 1 1 0 : f32 1 : f8 0 : f1 1 : Count source (clock selected by bits TCK2 to TCK0 in the TRDCRi register) Registers TRDDF0 to TRDDF1 in Input Capture Function Rev.1.10 Dec 21, 2007 REJ09B0406-0110 RW RW RW R8C/2K Group, R8C/2L Group 16. Timers Timer RD Control Register i (i = 0 or 1) b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRDCR0 TRDCR1 Bit Symbol Address 0140h 0150h Bit Name Count source select bits After Reset 00h 00h Function 0 0 0 0 1 1 1 1 TCK0 TCK1 TCK2 External clock edge select bits (2) CKEG1 TRDi counter clear select bits CCLR0 CCLR1 CCLR2 0 0 1 1 0 0 1 1 0 : f1 1 : f2 0 : f4 1 : f8 0 : f32 1 : TRDCLK input(1) 0 : fOCO40M 1 : Do not set. RW RW RW b4 b3 0 0 1 1 CKEG0 RW b2 b1 b0 0 : Count at the rising edge 1 : Count at the falling edge 0 : Count at both edges 1 : Do not set. RW RW b7 b6 b5 0 0 0 : Disable clear (free-running operation) 0 0 1 : Clear by input capture in the TRDGRAi register 0 1 0 : Clear by input capture in the TRDGRBi register 0 1 1 : Synchronous clear (clear simultaneously w ith other channel counter)(3) 1 0 0 : Do not set. 1 0 1 : Clear by input capture in the TRDGRCi register 1 1 0 : Clear by input capture in the TRDGRDi register 1 1 1 : Do not set. RW RW RW NOTES: 1. This setting is enabled w hen the STCLK bit in the TRDFCR register is set to 1 (external clock input enabled). 2. Bits CKEG1 to CKEG0 are enabled w hen bits TCK2 to TCK0 are set to 101b (TRDCLK input) and the STCLK bit in the TRDFCR register is set to 1 (external clock input enabled). 3. This setting is enabled w hen the SYNC bit in the TRDMR register is set to 1 (registers TRD0 and TRD1 operate synchronously). Figure 16.74 Registers TRDCR0 to TRDCR1 in Input Capture Function Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 233 of 450 R8C/2K Group, R8C/2L Group 16. Timers Timer RD I/O Control Register Ai (i = 0 or 1) b7 b6 b5 b4 b3 b2 b1 b0 1 1 Symbol TRDIORA0 TRDIORA1 Bit Symbol Address 0141h 0151h Bit Name TRDGRA control bits IOA1 IOA3 RW RW Set to 1 (input capture) in the input capture function. RW Input capture input sw itch bit(3, 4) 0 : fOCO128 Signal 1 : TRDIOA0 pin input RW TRDGRB control bits b5 b4 0 0 : Input capture to the TRDGRBi register at the rising edge 0 1 : Input capture to the TRDGRBi register at the falling edge 1 0 : Input capture to the TRDGRBi register at both edges 1 1 : Do not set. IOB1 -- (b7) RW TRDGRA mode select bit(1) IOB0 IOB2 Function b1 b0 0 0 : Input capture to the TRDGRAi register at the rising edge 0 1 : Input capture to the TRDGRAi register at the falling edge 1 0 : Input capture to the TRDGRAi register at both edges 1 1 : Do not set. IOA0 IOA2 After Reset 10001000b 10001000b TRDGRB mode select bit(2) Set to 1 (input capture) in the input capture function. Nothing is assigned. If necessary, set to 0. When read, the content is 1. RW RW RW -- NOTES: 1. To select 1 (the TRDGRCi register is used as a buffer register of the TRDGRAi register) for this bit by the BFCi bit in the TRDMR register, set the IOC2 bit in the TRDIORCi register to the same value as the IOA2 bit in the TRDIORAi register. 2. To select 1 (the TRDGRDi register is used as a buffer register of the TRDGRBi register) for this bit by the BFDi bit in the TRDMR register, set the IOD2 bit in the TRDIORCi register to the same value as the IOB2 bit in the TRDIORAi register. 3. The IOA3 bit is enabled in the TRDIORA0 register only. Set to the IOA3 bit in TRDIORA1 to 1. 4. The IOA3 bit is enabled w hen the IOA2 bit is set to 1 (input capture function). Figure 16.75 Registers TRDIORA0 to TRDIORA1 in Input Capture Function Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 234 of 450 R8C/2K Group, R8C/2L Group 16. Timers Timer RD I/O Control Register Ci (i = 0 or 1) b7 b6 b5 b4 b3 b2 b1 b0 1 1 1 1 Symbol TRDIORC0 TRDIORC1 Bit Symbol Address 0142h 0152h Bit Name TRDGRC control bits IOC1 IOC3 RW RW Set to 1 (input capture) in the input capture function. RW TRDGRC register function select bit Set to 1 (general register or buffer register) in the input capture function. RW TRDGRD control bits b5 b4 0 0 : Input capture to the TRDGRDi register at the rising edge 0 1 : Input capture to the TRDGRDi register at the falling edge 1 0 : Input capture to the TRDGRDi register at both edges 1 1 : Do not set. IOD1 IOD3 RW TRDGRC mode select bit(1) IOD0 IOD2 Function b1 b0 0 0 : Input capture to the TRDGRCi register at the rising edge 0 1 : Input capture to the TRDGRCi register at the falling edge 1 0 : Input capture to the TRDGRCi register at both edges 1 1 : Do not set. IOC0 IOC2 After Reset 10001000b 10001000b RW RW TRDGRD mode select bit(2) Set to 1 (input capture) in the input capture function. RW TRDGRD register function select bit Set to 1 (general register or buffer register) in the input capture function. RW NOTES: 1. To select 1 (the TRDGRCi register is used as a buffer register of the TRDGRAi register) for this bit by the BFCi bit in the TRDMR register, set the IOC2 bit in the TRDIORCi register to the same value as the IOA2 bit in the TRDIORAi register. 2. To select 1 (the TRDGRDi register is used as a buffer register of the TRDGRBi register) for this bit by the BFDi bit in the TRDMR register, set the IOD2 bit in the TRDIORCi register to the same value as the IOB2 bit in the TRDIORAi register. Figure 16.76 Registers TRDIORC0 to TRDIORC1 in Input Capture Function Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 235 of 450 R8C/2K Group, R8C/2L Group 16. Timers Timer RD Status Register i (i = 0 or 1) b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRDSR0 TRDSR1 Bit Symbol Address 0143h 0153h Bit Name Input capture/compare match flag A IMFA After Reset 11100000b 11000000b Function [Source for setting this bit to 0] Write 0 after read(2) [Source for setting this bit to 1] TRDSR0 register: fOCO128 signal edge w hen the IOA3 bit in the TRDIORA0 register is set to 0 (fOCO128 signal) TRDIOA0 pin input edge w hen the IOA3 bit in the TRDIORA0 register is set to 1 (TRDIOA0 input)(3) RW RW TRDSR1 register: Input edge of TRDIOA1 pin(3) IMFB IMFC IMFD Input capture/compare match flag B [Source for setting this bit to 0] Write 0 after read(2) [Source for setting this bit to 1] Input edge of TRDIOBi pin(3) RW Input capture/compare match flag C [Source for setting this bit to 0] Write 0 after read(2) [Source for setting this bit to 1] Input edge of TRDIOCi pin(4) RW Input capture/compare match flag D [Source for setting this bit to 0] Write 0 after read(2) [Source for setting this bit to 1] Input edge of TRDIODi pin(4) RW Overflow flag [Source for setting this bit to 0] Write 0 after read(2) [Source for setting this bit to 1] When the TRDi register overflow s RW OVF UDF -- (b7-b6) Underflow flag(1) This bit is disabled in the input capture function. RW Nothing is assigned. If necessary, set to 0. When read, the content is 1. NOTES: 1. Nothing is assigned to b5 in the TRDSR0 register. When w riting to b5, w rite 0. When reading, the content is 1. 2. The w riting results are as follow s: * This bit is set to 0 w hen the read result is 1 and 0 is w ritten to the same bit. * This bit remains unchanged even if the read result is 0 and 0 is w ritten to the same bit. (This bit remains 1 even if it is set to 1 from 0 after reading, and w riting 0.) * This bit remains unchanged if 1 is w ritten to it. 3. Edge selected by bits IOj1 to IOj0 (j = A or B) in the TRDIORAi register. 4. Edge selected by bits IOk1 to IOk0 (k = C or D) in the TRDIORCi register Including w hen the BFki bit in the TRDMR register is set to 1 (TRDGRki is used as the buffer register). Figure 16.77 Registers TRDSR0 to TRDSR1 in Input Capture Function Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 236 of 450 -- R8C/2K Group, R8C/2L Group 16. Timers Timer RD Interrupt Enable Register i (i = 0 or 1) b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRDIER0 TRDIER1 Bit Symbol After Reset 11100000b 11100000b Bit Name Input capture/compare match interrupt enable bit A Function 0 : Disable interrupt (IMIA) by the IMFA bit 1 : Enable interrupt (IMIA) by the IMFA bit IMIEB Input capture/compare match interrupt enable bit B 0 : Disable interrupt (IMIB) by the IMFB bit 1 : Enable interrupt (IMIB) by the IMFB bit RW IMIEC Input capture/compare match interrupt enable bit C 0 : Disable interrupt (IMIC) by the IMFC bit 1 : Enable interrupt (IMIC) by the IMFC bit RW IMIED Input capture/compare match interrupt enable bit D 0 : Disable interrupt (IMID) by the IMFD bit 1 : Enable interrupt (IMID) by the IMFD bit RW OVIE Overflow /underflow interrupt enable bit 0 : Disable interrupt (OVI) by the OVF bit 1 : Enable interrupt (OVI) by the OVF bit RW IMIEA -- (b7-b5) Figure 16.78 Address 0144h 0154h Nothing is assigned. If necessary, set to 0. When read, the content is 1. RW RW -- Registers TRDIER0 to TRDIER1 in Input Capture Function Timer RD Counter i (i = 0 or 1)(1) (b15) b7 (b8) b0 b7 b0 Symbol TRD0 TRD1 Address 0147h-0146h 0157h-0156h Function Count the count source. Count operation is incremented. When an overflow occurs, the OVF bit in the TRDSRi register is set to 1. NOTE: 1. Access the TRDi register in 16-bit units. Do not access it in 8-bit units. Figure 16.79 Registers TRD0 to TRD1 in Input Capture Function Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 237 of 450 After Reset 0000h 0000h Setting Range 0000h to FFFFh RW RW R8C/2K Group, R8C/2L Group 16. Timers Timer RD General Registers Ai, Bi, Ci, and Di (i = 0 or 1)(1) (b15) b7 (b8) b0 b7 b0 Symbol Address After Reset TRDGRA0 TRDGRB0 TRDGRC0 TRDGRD0 TRDGRA1 TRDGRB1 TRDGRC1 TRDGRD1 0149h-0148h 014Bh-014Ah 014Dh-014Ch 014Fh-014Eh 0159h-0158h 015Bh-015Ah 015Dh-015Ch 015Fh-015Eh FFFFh FFFFh FFFFh FFFFh FFFFh FFFFh FFFFh FFFFh Function Refer to Table 16.38 TRDGRji Register Functions in Input Capture Function RW RW NOTE: 1. Access registers TRDGRAi to TRDGRDi in 16-bit units. Do not access them in 8-bit units. Figure 16.80 Registers TRDGRAi, TRDGRBi, TRDGRCi, and TRDGRDi in Input Capture Function The following registers are disabled in the input capture function: TRDOER1, TRDOER2, TRDOCR, TRDPOCR0, and TRDPOCR1. Table 16.38 TRDGRji Register Functions in Input Capture Function Register TRDGRAi Setting - TRDGRBi TRDGRCi BFCi = 0 TRDGRDi BFDi = 0 TRDGRCi BFCi = 1 TRDGRDi BFDi = 1 Register Function General register The value in the TRDi register can be read at input capture. General register The value in the TRDi register can be read at input capture. Buffer register The value in the TRDi register can be read at input capture. (Refer to 16.4.2 Buffer Operation) Input-Capture Input Pin TRDIOAi TRDIOBi TRDIOCi TRDIODi TRDIOAi TRDIOBi i = 0 or 1, j = either A, B, C, or D BFCi, BFDi: Bits in TRDMR register Set the pulse width of the input capture signal applied to the TRDIOji pin to 3 cycles or more of the timer RD operation clock (refer to Table 16.25 Timer RD Operation Clocks) for no digital filter (the DFj bit in the TRDDFi register set to 0). Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 238 of 450 R8C/2K Group, R8C/2L Group 16. Timers TRDCLK input count source Count value in TRDi register FFFFh 0009h 0006h 0000h TSTARTi bit in TRDSTR register 1 0 65536 TRDIOAi input TRDGRAi register 0006h Transfer TRDGRCi register 0009h Transfer 0006h IMFA bit in TRDSRi register 1 OVF bit in TRDSRi register 1 0 Set to 0 by a program 0 i = 0 or 1 The above applies under the following conditions: Bits CCLR2 to CCLR0 in the TRDCRi register are set to 001b. (the TRDi register set to 0000h by TRDGRAi register input capture). Bits TCK2 to TCK0 in the TRDCRi register are set to 101b (TRDCLK input for the count source). Bits CKEG1 to CKEG0 in the TRDCRi register are set to 01b (count at the falling edge for the count source). Bits IOA2 to IOA0 in the TRDIORAi register are set to 101b (input capture at the falling edge of the TRDIOAi input). The BFCi bit in the TRDMR register is set to 1 (the TRDGRCi register is used as the buffer register of the TRDGRAi register). Figure 16.81 Operating Example of Input Capture Function Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 239 of 450 R8C/2K Group, R8C/2L Group 16.4.5.1 16. Timers Digital Filter The TRDIOji input is sampled, and when the sampled input level matches 3 times, its level is determined. Select the digital filter function and sampling clock by the TRDDFi register. Figure 16.82 shows a Block Diagram of Digital Filter. TCK2 to TCK0 fOCO40M TRDCLK f32 f8 f4 f2 DFCK1 to DFCK0 = 110b = 00b f32 = 101b = 01b f8 = 100b = 10b f1 = 011b = 11b Count source = 010b IOA2 to IOA0 IOB2 to IOB0 IOC3 to IOC0 IOD3 to IOD0 = 001b = 000b f1 Sampling clock DFj C TRDIOji input signal D C Q D Latch C Q D Latch 1 C Q Latch D Q Match detection circuit Edge detection circuit Latch 0 Timer RD operation clock f1, fOCO40M) C D Q Latch Clock period selected by bits TCK2 to TCK0 or bits DFCK1 to DFCK0 Sampling clock TRDIOji input signal Recognition of the signal change with 3-time match Input signal through digital filtering Signal transmission delayed up to 5-sampling clock Transmission cannot be performed without 3-time match because the input signal is assumed to be noise. i = 0 or 1, j = either A, B, C, or D TCK0 to TCK2: Bits in TRDCRi register DFCK0 to DFCK1 and DFj: Bits in TRDDF register IOA0 to IOA2 and IOB0 to IOB2: Bits in TRDIORAi register IOC0 to IOC3 and IOD0 to IOD3: Bits in TRDIORCi register Figure 16.82 Block Diagram of Digital Filter Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 240 of 450 R8C/2K Group, R8C/2L Group 16.4.6 16. Timers Output Compare Function This function detects matches (compare match) between the content of the TRDGRji (j = either A, B, C, or D) register and the content of the TRDi (i = 0 or 1) register. When the content matches, a user-set level is output from the TRDIOji pin. Since this function is enabled with a combination of the TRDIOji pin and TRDGRji register, the output compare function, or any other mode or function, can be selected for each individual pin. Figure 16.83 shows a Block Diagram of Output Compare Function, Table 16.39 lists the Output Compare Function Specifications. Figures 16.84 to 16.95 list the Registers Associated with Output Compare Function, and Figure 16.96 shows an Operating Example of Output Compare Function. Channel 0 TRD0 Compare match signal Output control TRDIOA0 IOC3 = 0 in TRDIORC0 register Comparator TRDGRA0 Comparator TRDGRC0 Comparator TRDGRB0 Comparator TRDGRD0 Compare match signal Output control TRDIOC0 IOC3 = 1 Compare match signal Output control TRDIOB0 IOD3 = 0 in TRDIORD0 register Compare match signal Output control TRDIOD0 IOD3 = 1 Channel 1 TRD1 Compare match signal Output control TRDIOA1 IOC3 = 0 in TRDIORC1 register Comparator TRDGRA1 Comparator TRDGRC1 Comparator TRDGRB1 Comparator TRDGRD1 Compare match signal Output control TRDIOC1 IOC3 = 1 Compare match signal Output control TRDIOB1 IOD3 = 0 in TRDIORD1 register Compare match signal Output control TRDIOD1 Figure 16.83 IOD3 = 1 Block Diagram of Output Compare Function Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 241 of 450 R8C/2K Group, R8C/2L Group Table 16.39 16. Timers Output Compare Function Specifications Item Specification Count sources f1, f2, f4, f8, f32, fOCO40M External signal input to the TRDCLK pin (valid edge selected by a program) Count operations Increment Count period * When bits CCLR2 to CCLR0 in the TRDCRi register are set to 000b (free-running operation) 1/fk x 65536 fk: Frequency of count source * Bits CCLR1 to CCLR0 in the TRDCRi register are set to 01b or 10b (set the TRDi register to 0000h at the compare match in the TRDGRji register). Frequency of count source x (n+1) n: Setting value in the TRDGRji register Waveform output timing Compare match Count start condition 1 (count starts) is written to the TSTARTi bit in the TRDSTR register. Count stop conditions * 0 (count stops) is written to the TSTARTi bit in the TRDSTR register when the CSELi bit in the TRDSTR register is set to 1. The output compare output pin holds output level before the count stops. * When the CSELi bit in the TRDSTR register is set to 0, the count stops at the compare match in the TRDGRAi register. The output compare output pin holds level after output change by the compare match. Interrupt request generation timing * Compare match (content of the TRDi register matches content of the TRDGRji register.) * TRDi register overflows TRDIOA0 pin function Programmable I/O port, output-compare output, or TRDCLK (external clock) input TRDIOB0, TRDIOC0, TRDIOD0, TRDIOA1 to TRDIOD1 pin functions Programmable I/O port or output-compare output (Selectable by pin) INT0 pin function Programmable I/O port, pulse output forced cutoff signal input, or INT0 interrupt input Read from timer The count value can be read by reading the TRDi register. Write to timer * When the SYNC bit in the TRDMR register is set to 0 (channels 0 and 1 operate independently). Data can be written to the TRDi register. * When the SYNC bit in the TRDMR register is set to 1 (channels 0 and 1 operate synchronously). Data can be written to both the TRD0 and TRD1 registers by writing to the TRDi register. Select functions * Output-compare output pin selected Either 1 pin or multiple pins among TRDIOAi, TRDIOBi, TRDIOCi, or TRDIODi. * Output level at the compare match selected "L" output, "H" output, or output level inversed * Initial output level selected Set the level at period from the count start to the compare match. * Timing to set the TRDi register to 0000h Overflow or compare match in the TRDGRAi register * Buffer operation (Refer to 16.4.2 Buffer Operation.) * Synchronous operation (Refer to 16.4.3 Synchronous Operation.) * Output pin in registers TRDGRCi and TRDGRDi changed The TRDGRCi register can be used as output control of the TRDIOAi pin and the TRDGRDi register can be used as output control of the TRDIOBi pin. * Pulse output forced cutoff signal input (Refer to 16.4.4 Pulse Output Forced Cutoff.) * Timer RD can be used as the internal timer without output. i = 0 or 1, j = either A, B, C, or D Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 242 of 450 R8C/2K Group, R8C/2L Group 16. Timers Timer RD Start Register(1) b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRDSTR Bit Symbol TSTART0 TSTART1 CSEL0 CSEL1 -- (b7-b4) Address 0137h Bit Name TRD0 count start flag(4) After Reset 11111100b Function RW 0 : Count stops (2) 1 : Count starts RW TRD1 count start flag(5) 0 : Count stops (3) 1 : Count starts RW TRD0 count operation select bit 0 : Count stops at the compare match w ith the TRDGRA0 register 1 : Count continues after the compare match w ith the TRDGRA0 register RW TRD1 count operation select bit 0 : Count stops at the compare match w ith the TRDGRA1 register 1 : Count continues after the compare match w ith the TRDGRA1 register RW Nothing is assigned. If necessary, set to 0. When read, the content is 1. -- NOTES: 1. Set the TRDSTR register using the MOV instruction (do not use the bit handling instruction). Refer to 16.4.12.1 TRDSTR Register of Notes on Tim er RD. 2. When the CSEL0 bit is 3. When the CSEL1 bit is 4. When the CSEL0 bit is stops). 5. When the CSEL1 bit is stops). set to 1, w rite 0 to the TSTART0 bit. set to 1, w rite 0 to the TSTART1 bit. set to 0 and the compare match signal (TRDIOA0) is generated, this bit is set to 0 (count set to 0 and the compare match signal (TRDIOA1) is generated, this bit is set to 0 (count Timer RD Mode Register b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRDMR Bit Symbol Address 0138h Bit Name Timer RD synchronous bit SYNC -- (b3-b1) After Reset 00001110b Function 0 : Registers TRD0 and TRD1 operate independently 1 : Registers TRD0 and TRD1 operate synchronously -- BFC0 TRDGRC0 register function select 0 : General register bit(1) 1 : Buffer register of TRDGRA0 register RW BFD0 TRDGRD0 register function select 0 : General register bit(1) 1 : Buffer register of TRDGRB0 register RW BFC1 TRDGRC1 register function select 0 : General register bit(1) 1 : Buffer register of TRDGRA1 register RW BFD1 TRDGRD1 register function select 0 : General register 1 : Buffer register of TRDGRB1 register bit(1) RW Registers TRDSTR and TRDMR in Output Compare Function Rev.1.10 Dec 21, 2007 REJ09B0406-0110 RW Nothing is assigned. If necessary, set to 0. When read, the content is 1. NOTE: 1. When selecting 0 (change the TRDGRji register output pin) by the IOj3 (j = C or D) bit in the TRDIORCi (i = 0 or 1) register, set the BFji bit in the TRDMR register to 0. Figure 16.84 RW Page 243 of 450 R8C/2K Group, R8C/2L Group 16. Timers Timer RD PWM Mode Register b7 b6 b5 b4 b3 b2 b1 b0 0 0 0 0 0 0 Symbol TRDPMR Bit Symbol PWMB0 PWMC0 PWMD0 -- (b3) PWMB1 PWMC1 PWMD1 -- (b7) Figure 16.85 Address 0139h Bit Name PWM mode of TRDIOB0 select bit After Reset 10001000b Function Set to 0 (timer mode) in the output compare function. RW PWM mode of TRDIOC0 select bit Set to 0 (timer mode) in the output compare function. RW PWM mode of TRDIOD0 select bit Set to 0 (timer mode) in the output compare function. RW Nothing is assigned. If necessary, set to 0. When read, the content is 1. -- PWM mode of TRDIOB1 select bit Set to 0 (timer mode) in the output compare function. RW PWM mode of TRDIOC1 select bit Set to 0 (timer mode) in the output compare function. RW PWM mode of TRDIOD1 select bit Set to 0 (timer mode) in the output compare function. RW Nothing is assigned. If necessary, set to 0. When read, the content is 1. TRDPMR Register in Output Compare Function Rev.1.10 Dec 21, 2007 REJ09B0406-0110 RW Page 244 of 450 -- R8C/2K Group, R8C/2L Group 16. Timers Timer RD Function Control Register b7 b6 b5 b4 b3 b2 b1 b0 1 0 0 Symbol TRDFCR Bit Symbol CMD0 Address 013Ah Bit Name Combination mode select bits (1) After Reset 10000000b Function Set to 00b (timer mode, PWM mode, or PWM3 mode) in the output compare function. CMD1 RW OLS0 RW OLS1 Counter-phase output level select bit This bit is disabled in the output compare (in reset synchronous PWM mode or function. complementary PWM mode) RW ADTRG A/D trigger enable bit (in complementary PWM mode) This bit is disabled in the output compare function. RW ADEG A/D trigger edge select bit (in complementary PWM mode) This bit is disabled in the output compare function. RW External clock input select bit 0 : External clock input disabled 1 : External clock input enabled RW PWM3 mode select bit(2) Set this bit to 1 (other than PWM3 mode) in the output compare function. RW PWM3 NOTES: 1. Set bits CMD1 to CMD0 w hen both the TSTART0 and TSTART1 bits are set to 0 (count stops). 2. When bits CMD1 to CMD0 are set to 00b (timer mode, PWM mode, or PWM3 mode), the setting of the PWM3 bit is enabled. TRDFCR Register in Output Compare Function Rev.1.10 Dec 21, 2007 REJ09B0406-0110 RW Normal-phase output level select bit This bit is disabled in the output compare (in reset synchronous PWM mode or function. complementary PWM mode) STCLK Figure 16.86 RW Page 245 of 450 R8C/2K Group, R8C/2L Group 16. Timers Timer RD Output Master Enable Register 1 b7 b6 b5 b4 b3 b2 b1 b0 1 1 Symbol TRDOER1 Bit Symbol Address 013Bh Bit Name TRDIOA0 output disable bit EA0 TRDIOB0 output disable bit EB0 TRDIOC0 output disable bit EC0 TRDIOD0 output disable bit ED0 TRDIOA1 output disable bit EA1 TRDIOB1 output disable bit EB1 TRDIOC1 output disable bit EC1 TRDIOD1 output disable bit ED1 After Reset FFh Function 0 : Enable output 1 : Disable output (The TRDIOA0 pin is used as a programmable I/O port.) RW RW 0 : Enable output 1 : Disable output (The TRDIOB0 pin is used as a programmable I/O port.) RW 0 : Enable output 1 : Disable output (The TRDIOC0 pin is used as a programmable I/O port.) RW 0 : Enable output 1 : Disable output (The TRDIOD0 pin is used as a programmable I/O port.) RW 0 : Enable output 1 : Disable output (The TRDIOA1 pin is used as a programmable I/O port.) RW 0 : Enable output 1 : Disable output (The TRDIOB1 pin is used as a programmable I/O port.) RW 0 : Enable output 1 : Disable output (The TRDIOC1 pin is used as a programmable I/O port.) RW 0 : Enable output 1 : Disable output (The TRDIOD1 pin is used as a programmable I/O port.) RW Timer RD Output Master Enable Register 2 b7 b6 b5 b4 b3 b2 b1 b0 Symbol Address 013Ch TRDOER2 Bit Symbol Bit Name -- Nothing is assigned. If necessary, set to 0. (b6-b0) When read, the content is 1. After Reset 01111111b Function RW -- _____ PTO INT0 of pulse output forced cutoff signal input enabled bit(1) 0 : Pulse output forced cutoff input disabled 1 : Pulse output forced cutoff input enabled (All bits in the TRDOER1 register are set to 1 (disable output) w hen "L" is _____ applied to the INT0 pin.) NOTE: 1. Refer to 16.4.4 Pulse Output Forced Cutoff. Figure 16.87 Registers TRDOER1 to TRDOER2 in Output Compare Function Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 246 of 450 RW R8C/2K Group, R8C/2L Group 16. Timers Timer RD Output Control Register(1, 2) b7 b6 b5 b4 b3 b2 b1 b0 0 0 1 Symbol TRDOCR Bit Symbol TOA0 TOB0 TOC0 TOD0 TOA1 TOB1 TOC1 TOD1 Address 013Dh Bit Name TRDIOA0 output level select bit After Reset 00h Function 0 : Initial output "L" 1 : Initial output "H" RW TRDIOB0 output level select bit 0 : Initial output "L" 1 : Initial output "H" RW TRDIOC0 initial output level select bit 0 : "L" 1 : "H" RW TRDIOD0 initial output level select bit TRDIOA1 initial output level select bit TRDIOB1 initial output level select bit TRDIOC1 initial output level select bit TRDIOD1 initial output level select bit RW RW RW RW RW RW NOTES: 1. Write to the TRDOCR register w hen both the TSTART0 and TSTART1 bits in the TRDSTR register are set to 0 (count stopped). 2. If the pin function is set for w aveform output (refer to Tables 16.26 to 16.33), the initial output level is output w hen the TRDOCR register is set. Figure 16.88 TRDOCR Register in Output Compare Function Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 247 of 450 R8C/2K Group, R8C/2L Group 16. Timers Timer RD Control Register i (i = 0 or 1) b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRDCR0 TRDCR1 Bit Symbol Address 0140h 0150h Bit Name Count source select bits Function TCK1 TCK2 External clock edge select bits (2) CKEG1 TRDi counter clear select bits CCLR0 CCLR1 CCLR2 RW b2 b1 b0 0 0 0 0 1 1 1 1 TCK0 CKEG0 After Reset 00h 00h 0 0 1 1 0 0 1 1 0 : f1 1 : f2 0 : f4 1 : f8 0 : f32 1 : TRDCLK input(1) 0 : fOCO40M 1 : Do not set. RW RW RW b4 b3 0 0 1 1 0 : Count at the rising edge 1 : Count at the falling edge 0 : Count at both edges 1 : Do not set. RW RW b7 b6 b5 0 0 0 : Disable clear (free-running operation) 0 0 1 : Clear by compare match w ith the TRDGRAi register 0 1 0 : Clear by compare match w ith the TRDGRBi register 0 1 1 : Synchronous clear (clear simultaneously w ith other channel counter)(3) 1 0 0 : Do not set. 1 0 1 : Clear by compare match w ith the TRDGRCi register 1 1 0 : Clear by compare match w ith the TRDGRDi register 1 1 1 : Do not set. RW RW RW NOTES: 1. This setting is enabled w hen the STCLK bit in the TRDFCR register is set to 1 (external clock input enabled). 2. Bits CKEG1 to CKEG0 are enabled w hen bits TCK2 to TCK0 are set to 101b (TRDCLK input) and the STCLK bit in the TRDFCR register is set to 1 (external clock input enabled). 3. This setting is enabled w hen the SYNC bit in the TRDMR register is set to 1 (TRD0 and TRD1 operate synchronously). Figure 16.89 Registers TRDCR0 to TRDCR1 in Output Compare Function Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 248 of 450 R8C/2K Group, R8C/2L Group 16. Timers Timer RD I/O Control Register Ai (i = 0 or 1) b7 b6 b5 b4 b3 b2 b1 b0 0 1 0 Symbol TRDIORA0 TRDIORA1 Bit Symbol Address 0141h 0151h Bit Name TRDGRA control bits After Reset 10001000b 10001000b Function 0 0 : Disable pin output by the compare match (TRDIOAi pin functions as programmable I/O port) 0 1 : "L" output at compare match w ith the TRDGRAi register 1 0 : "H" output at compare match w ith the TRDGRAi register 1 1 : Toggle output by compare match w ith the TRDGRAi register IOA0 IOA1 RW b1 b0 RW RW IOA2 TRDGRA mode select bit(1) Set to 0 (output compare) in the output compare function. RW IOA3 Input capture input sw itch bit Set to 1. RW TRDGRB control bits b5 b4 0 0 : Disable pin output by the compare match (TRDIOBi pin functions as programmable I/O port) 0 1 : "L" output at compare match w ith the TRDGRBi register 1 0 : "H" output at compare match w ith the TRDGRBi 1 1 : Toggle output by compare match w ith the TRDGRBi register IOB0 IOB1 IOB2 -- (b7) TRDGRB mode select bit(2) Set to 0 (output compare) in the output compare function. Nothing is assigned. If necessary, set to 0. When read, the content is 1. RW RW RW -- NOTES: 1. To select 1 (the TRDGRCi register is used as a buffer register of the TRDGRAi register) for this bit by the BFCi bit in the TRDMR register, set the IOC2 bit in the TRDIORCi register to the same value as the IOA2 bit in the TRDIORAi register. 2. To select 1 (the TRDGRDi register is used as a buffer register of the TRDGRBi register) for this bit by the BFDi bit in the TRDMR register, set the IOD2 bit in the TRDIORCi register to the same value as the IOB2 bit in the TRDIORAi register. Figure 16.90 Registers TRDIORA0 to TRDIORA1 in Output Compare Function Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 249 of 450 R8C/2K Group, R8C/2L Group 16. Timers Timer RD I/O Control Register Ci (i = 0 or 1) b7 b6 b5 b4 b3 b2 b1 b0 0 0 Symbol TRDIORC0 TRDIORC1 Bit Symbol Address 0142h 0152h Bit Name TRDGRC control bits IOC1 RW RW RW TRDGRC mode select bit(1) Set to 0 (output compare) in the output compare function. RW TRDGRC register function select bit 0 : TRDIOA output register (Refer to 16.4.6.1 Changing Output Pins in Registers TRDGRCi (i = 0 or 1) and TRDGRDi.) 1 : General register or buffer register RW IOC3 TRDGRD control bits b5 b4 0 0 : Disable pin output by compare match 0 1 : "L" output at compare match w ith the TRDGRDi register 1 0 : "H" output at compare match w ith the TRDGRDi register 1 1 : Toggle output by compare match w ith the TRDGRDi register IOD0 IOD1 IOD2 Function b1 b0 0 0 : Disable pin output by compare match 0 1 : "L" output at compare match w ith the TRDGRCi register 1 0 : "H" output at compare match w ith the TRDGRCi register 1 1 : Toggle output by compare match w ith the TRDGRCi register IOC0 IOC2 After Reset 10001000b 10001000b RW RW TRDGRD mode select bit(2) Set to 0 (output compare) in the output compare function. RW TRDGRD register function select bit 0 : TRDIOB output register (Refer to 16.4.6.1 Changing Output Pins in Registers TRDGRCi (i = 0 or 1) and TRDGRDi.) 1 : General register or buffer register RW IOD3 NOTES: 1. To select 1 (the TRDGRCi register is used as a buffer register of the TRDGRAi register) for this bit by the BFCi bit in the TRDMR register, set the IOC2 bit in the TRDIORCi register to the same value as the IOA2 bit in the TRDIORAi register. 2. To select 1 (the TRDGRDi register is used as a buffer register of the TRDGRBi register) for this bit by the BFDi bit in the TRDMR register, set the IOD2 bit in the TRDIORCi register to the same value as the IOB2 bit in the TRDIORAi register. Figure 16.91 Registers TRDIORC0 to TRDIORC1 in Output Compare Function Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 250 of 450 R8C/2K Group, R8C/2L Group 16. Timers Timer RD Status Register i (i=0 or 1) b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRDSR0 TRDSR1 Bit Symbol IMFA Address 0143h 0153h After Reset 11100000b 11000000b Bit Name Function Input capture/compare match [Source for setting this bit to 0] flag A Write 0 after read(2). [Source for setting this bit to 1] When the value in the TRDi register matches w ith the value in the TRDGRAi register. IMFB RW IMFC Input capture/compare match [Source for setting this bit to 0] flag C Write 0 after read(2). [Source for setting this bit to 1] When the value in the TRDi register matches w ith the value in the TRDGRCi register (3). RW IMFD Input capture/compare match [Source for setting this bit to 0] flag D Write 0 after read(2). [Source for setting this bit to 1] When the value in the TRDi register matches w ith the value in the TRDGRDi register (3). RW OVF UDF -- (b7-b6) Underflow flag(1) [Source for setting this bit to 0] Write 0 after read(2). [Source for setting this bit to 1] When the TRDi register overflow s. This bit is disabled in the output compare function. Nothing is assigned. If necessary, set to 0. When read, the content is 1. NOTES: 1. Nothing is assigned to b5 in the TRDSR0 register. When w riting to b5, w rite 0. When reading, the content is 1. 2. The w riting results are as follow s: * This bit is set to 0 w hen the read result is 1 and 0 is w ritten to the same bit. * This bit remains unchanged even if the read result is 0 and 0 is w ritten to the same bit. (This bit remains 1 even if it is set to 1 from 0 after reading, and w riting 0.) * This bit remains unchanged if 1 is w ritten to it. 3. Including w hen the BFji bit in the TRDMR register is set to 1 (TRDGRji is used as the buffer register). Registers TRDSR0 to TRDSR1 in Output Compare Function Rev.1.10 Dec 21, 2007 REJ09B0406-0110 RW Input capture/compare match [Source for setting this bit to 0] flag B Write 0 after read(2). [Source for setting this bit to 1] When the value in the TRDi register matches w ith the value in the TRDGRBi register. Overflow flag Figure 16.92 RW Page 251 of 450 RW RW -- R8C/2K Group, R8C/2L Group 16. Timers Timer RD Interrupt Enable Register i (i = 0 or 1) b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRDIER0 TRDIER1 Bit Symbol IMIEA IMIEB IMIEC IMIED OVIE -- (b7-b5) Figure 16.93 Address 0144h 0154h After Reset 11100000b 11100000b Bit Name Input capture/compare match interrupt enable bit A Function 0 : Disable interrupt (IMIA) by the IMFA bit 1 : Enable interrupt (IMIA) by the IMFA bit Input capture/compare match interrupt enable bit B 0 : Disable interrupt (IMIB) by the IMFB bit 1 : Enable interrupt (IMIB) by the IMFB bit RW Input capture/compare match interrupt enable bit C 0 : Disable interrupt (IMIC) by the IMFC bit 1 : Enable interrupt (IMIC) by the IMFC bit RW Input capture/compare match interrupt enable bit D 0 : Disable interrupt (IMID) by the IMFD bit 1 : Enable interrupt (IMID) by the IMFD bit RW Overflow /underflow interrupt enable 0 : Disable interrupt (OVI) by the bit OVF bit 1 : Enable interrupt (OVI) by the OVF bit RW Nothing is assigned. If necessary, set to 0. When read, the content is 1. -- Registers TRDIER0 to TRDIER1 in Output Compare Function Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 252 of 450 RW RW R8C/2K Group, R8C/2L Group 16. Timers Timer RD Counter i (i = 0 or 1)(1) (b15) b7 (b8) b0 b7 b0 Symbol Address 0147h-0146h 0157h-0156h TRD0 TRD1 Function Count a count source. Count operation is incremented. When an overflow occurs, the OVF bit in the TRDSRi register is set to 1. After Reset 0000h 0000h Setting Range 0000h to FFFFh RW RW NOTE: 1. Access the TRDi register in 16-bit units. Do not access it in 8-bit units. Figure 16.94 Registers TRD0 to TRD1 in Output Compare Function Timer RD General Register Ai, Bi, Ci and Di (i = 0 or 1)(1) (b15) b7 (b8) b0 b7 b0 Symbol Address After Reset TRDGRA0 TRDGRB0 TRDGRC0 TRDGRD0 TRDGRA1 TRDGRB1 TRDGRC1 TRDGRD1 0149h-0148h 014Bh-014Ah 014Dh-014Ch 014Fh-014Eh 0159h-0158h 015Bh-015Ah 015Dh-015Ch 015Fh-015Eh FFFFh FFFFh FFFFh FFFFh FFFFh FFFFh FFFFh FFFFh Function Refer to Table 16.40 TRDGRji Register Function in Output Com pare Function RW RW NOTE: 1. Access registers TRDGRAi to TRDGRDi in 16-bit units. Do not access them in 8-bit units. Figure 16.95 Registers TRDGRAi, TRDGRBi, TRDGRCi, and TRDGRDi in Output Compare Function The following registers are disabled in the output compare function: TRDDF0, TRDDF1, TRDPOCR0, and TRDPOCR1. Table 16.40 Register TRDGRAi TRDGRBi TRDGRCi TRDGRDi TRDGRCi TRDGRDi TRDGRCi TRDGRDi TRDGRji Register Function in Output Compare Function Setting BFji IOj3 - - 0 1 1 1 0 0 Output-Compare Output Pin General register. Write the compare value. TRDIOAi TRDIOBi General register. Write the compare value. TRDIOCi TRDIODi Buffer register. Write the next compare value TRDIOAi (Refer to 16.4.2 Buffer Operation.) TRDIOBi TRDIOAi output control (Refer to 16.4.6.1 Changing TRDIOAi Output Pins in Registers TRDGRCi (i = 0 or 1) and TRDIOBi TRDGRDi.) Register Function i = 0 or 1, j = either A, B, C, or D BFji: Bit in TRDMR register IOj3: Bit in TRDIORCi register Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 253 of 450 R8C/2K Group, R8C/2L Group 16. Timers Count source Value in TRDi register m n p Count restarts Count stops TSTARTi bit in TRDSTR register 1 0 m+1 m+1 Output level held TRDIOAi output Output inverted by compare match Initial output "L" IMFA bit in TRDSRi register 1 0 Set to 0 by a program n+1 TRDIOBi output "H" output by compare match Output level held n+1 Initial output "L" IMFB bit in TRDSRi register 1 0 Set to 0 by a program P+1 "L" output by compare match Output level held TRDIOCi output Initial output "H" IMFC bit in TRDSRi register 1 0 Set to 0 by a program i = 0 or 1 M: Value set in TRDGRAi register n: Value set in TRDGRBi register p: Value set in TRDGRCi register The above applies under the following conditions: The CSELi bit in the TRDSTR register is set to 1 (the TRDi register is not stopped by compare match). Bits BFCi and BFDi in the TRDMR register are set to 0 (registers TRDGRCi and TRDGRDi are not used as buffer registers). Bits EAi, EBi, and ECi in the TRDOER1 register are set to 0 (enable the TRDIOAi, TRDIOBi and TRDIOCi pin outputs). Bits CCLR2 to CCLR0 in the TRDCRi register are set to 001b (set the TRDi register to 000h by compare match in the TRDGRAi register). Bits TOAi and TOBi in the TRDOCR register is set to 0 (initial output "L" to compare match), the TOCi bit is set to 1 (initial output "H" to compare match). Bits IOA2 to IOA0 in the TRDIORAi register are set to 011b (TRDIOAi output inverted at TRDGRAi register compare match). Bits IOB2 to IOB0 in the TRDIORAi register are set to 010b (TRDIOBi "H" output at TRDGRBi register compare match). Bits IOC3 to IOC0 in the TRDIORCi register are set to 1001b (TRDIOCi "L" output at TRDGRCi register compare match). The IOD3 bit in the TRDIORCi register is set to 1 (TRDGRDi register does not control TRDIOBi pin output). Figure 16.96 Operating Example of Output Compare Function Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 254 of 450 R8C/2K Group, R8C/2L Group 16.4.6.1 16. Timers Changing Output Pins in Registers TRDGRCi (i = 0 or 1) and TRDGRDi The TRDGRCi register can be used for output control of the TRDIOAi pin, and the TRDGRDi register can be used for output control of the TRDIOBi pin. Therefore, each pin output can be controlled as follows: * TRDIOAi output is controlled by the values in registers TRDGRAi and TRDGRCi. * TRDIOBi output is controlled by the values in registers TRDGRBi and TRDGRDi. Change output pins in registers TRDGRCi and TRDGRDi as follows: * Select 0 (change TRDGRji register output pin) by the IOj3 (j = C or D) bit in the TRDIORCi register. * Set the BFji bit in the TRDMR register to 0 (general register). * Set different values in registers TRDGRCi and TRDGRAi. Also, set different values in registers TRDGRDi and TRDGRBi. Figure 16.98 shows an Operating Example When TRDGRCi Register is Used for Output Control of TRDIOAi Pin and TRDGRDi Register is Used for Output Control of TRDIOBi Pin. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 255 of 450 R8C/2K Group, R8C/2L Group 16. Timers Channel 0 TRD0 Compare match signal Output control TRDIOA0 IOC3 = 0 in TRDIORC0 register Comparator TRDGRA0 Comparator TRDGRC0 Comparator TRDGRB0 Comparator TRDGRD0 Compare match signal Output control TRDIOC0 IOC3 = 1 Compare match signal Output control TRDIOB0 IOD3 = 0 in TRDIORD0 register Compare match signal Output control TRDIOD0 IOD3 = 1 Channel 1 TRD1 Compare match signal Output control TRDIOA1 IOC3 = 0 in TRDIORC1 register Comparator TRDGRA1 Comparator TRDGRC1 Comparator TRDGRB1 Comparator TRDGRD1 Compare match signal Output control TRDIOC1 IOC3 = 1 Compare match signal Output control TRDIOB1 IOD3 = 0 in TRDIORD1 register Compare match signal Output control TRDIOD1 Figure 16.97 IOD3 = 1 Changing Output Pins in Registers TRDGRCi and TRDGRDi Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 256 of 450 R8C/2K Group, R8C/2L Group 16. Timers Count source Value in TRDi register FFFFh m n p q 0000h m+1 n+1 m-n p+1 q+1 p-q Initial output "L" TRDIOAi output Output inverted by compare match IMFA bit in TRDSRi register 1 0 Set to 0 by a program IMFC bit in TRDSRi register Set to 0 by a program 1 0 Initial output "L" TRDIOBi output Output inverted by compare match IMFB bit in TRDSRi register 1 IMFD bit in TRDSRi register 1 0 Set to 0 by a program Set to 0 by a program 0 m: Value set in TRDGRAi register n: Value set in TRDGRCi register p: Value set in TRDGRBi register q: Value set in TRDGRDi register i = 0 or 1 The above applies under the following conditions: The CSELi bit in the TRDSTR register is set to 1 (the TRDi register is not stopped by compare match). Bits BFCi and BFDi in the TRDMR register are set to 0 (registers TRDGRCi and TRDGRDi are not used as buffer register). Bits EAi and EBi in the TRDOER1 register are set to 0 (enable TRDIOAi and TRDIOBi pin outputs). Bits CCLR2 to CCLR0 in the TRDCRi register are set to 001b (set the TRDi register to 0000h by compare match in the TRDGRAi register). Bits TOAi and TOBi in the TRDOCR register are set to 0 (initial output "L" to compare match). Bits IOA2 to IOA0 in the TRDIORAi register are set to 011b (TRDIOAi output inverted at TRDGRAi register compare match). Bits IOB2 to IOB0 in the TRDIORAi register are set to 011b (TRDIOBi output inverted at TRDGRBi register compare match). Bits IOC3 to IOC0 in the TRDIORCi register are set to 0011b (TRDIOAi output inverted at TRDGRCi register compare match). Bits IOD3 to IOD0 in the TRDIORCi register are set to 0011b (TRDIOBi output inverted at TRDGRDi register compare match). Figure 16.98 Operating Example When TRDGRCi Register is Used for Output Control of TRDIOAi Pin and TRDGRDi Register is Used for Output Control of TRDIOBi Pin Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 257 of 450 R8C/2K Group, R8C/2L Group 16.4.7 16. Timers PWM Mode In PWM mode, a PWM waveform is output. Up to 3 PWM waveforms with the same period can be output by 1 channel. Also, up to 6 PWM waveforms with the same period can be output by synchronizing channels 0 and 1. Since this mode functions by a combination of the TRDIOji (i = 0 or 1, j = B, C, or D) pin and TRDGRji register, the PWM mode, or any other mode or function, can be selected for each individual pin. (However, since the TRDGRAi register is used when using any pin for PWM mode, the TRDGRAi register cannot be used for other modes.) Figure 16.99 shows a Block Diagram of PWM Mode, and Table 16.41 lists the PWM Mode Specifications. Figures 16.100 to 16.109 show the Registers Associated with PWM Mode, and Figures 16.110 and 16.111 show Operating Examples of PWM Mode. TRDi Compare match signal Comparator TRDIOBi TRDGRAi Compare match signal (Note 1) TRDIOCi Output control Comparator TRDGRBi Comparator TRDGRCi Compare match signal TRDIODi Compare match signal (Note 2) Comparator TRDGRDi i = 0 or 1 NOTES: 1. When the BFCi bit in the TRDMR register is set to 1 (the TRDGRCi register is used as the buffer register of the TRDGRAi register). 2. When the BFDi bit in the TRDMR register is set to 1 (the TRDGRDi register is used as the buffer register of the TRDGRBi register). Figure 16.99 Block Diagram of PWM Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 258 of 450 R8C/2K Group, R8C/2L Group Table 16.41 16. Timers PWM Mode Specifications Item Specification Count sources f1, f2, f4, f8, f32, fOCO40M External signal input to the TRDCLK pin (valid edge selected by a program) Count operations Increment PWM waveform PWM period: 1/fk x (m+1) Active level width: 1/fk x (m-n) Inactive level width: 1/fk x (n+1) fk: Frequency of count source m: Value set in the TRDGRAi (i = 0 or 1) register n: Value set in the TRDGRji (j = B, C, or D) register m+1 n+1 m-n (When "L" is selected as the active level) Count start condition 1 (count starts) is written to the TSTARTi bit in the TRDSTR register. Count stop conditions * 0 (count stops) is written to the TSTARTi bit in the TRDSTR register when the CSELi bit in the TRDSTR register is set to 1. The PWM output pin holds output level before the count stops. * When the CSELi bit in the TRDSTR register is set to 0, the count stops at the compare match in the TRDGRAi register. The PWM output pin holds level after output change by compare match. Interrupt request generation timing * Compare match (The content of the TRDi register matches content of the TRDGRji register.) * TRDi register overflows TRDIOA0 pin function Programmable I/O port or TRDCLK (external clock) input TRDIOA1 pin function Programmable I/O port TRDIOB0, TRDIOC0, TRDIOD0, Programmable I/O port or pulse output (selectable by pin) TRDIOB1, TRDIOC1, TRDIOD1 pin functions INT0 pin function Programmable I/O port, pulse output forced cutoff signal input, or INT0 interrupt input Read from timer The count value can be read by reading the TRDi register. Write to timer The value can be written to the TRDi register. Select functions * 1 to 3 PWM output pins selected per 1 channel Either 1 pin or multiple pins of the TRDIOBi, TRDIOCi or TRDIODi pin. * The active level selected by pin. * Initial output level selected by pin. * Synchronous operation (Refer to 16.4.3 Synchronous Operation.) * Buffer operation (Refer to 16.4.2 Buffer Operation.) * Pulse output forced cutoff signal input (Refer to 16.4.4 Pulse Output Forced Cutoff.) i = 0 or 1 Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 259 of 450 R8C/2K Group, R8C/2L Group 16. Timers Timer RD Start Register(1) b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRDSTR Bit Symbol TSTART0 TSTART1 Address 0137h Bit Name TRD0 count start flag(4) TRD1 count start flag(5) After Reset 11111100b Function RW 0 : Count stops (2) 1 : Count starts RW 0 : Count stops (3) 1 : Count starts RW CSEL0 TRD0 count operation select bit 0 : Count stops at the compare match w ith the TRDGRA0 register 1 : Count continues after the compare match w ith the TRDGRA0 register RW CSEL1 TRD1 count operation select bit 0 : Count stops at the compare match w ith the TRDGRA1 register 1 : Count continues after the compare match w ith the TRDGRA1 register RW -- (b7-b4) Nothing is assigned. If necessary, set to 0. When read, the content is 1. -- NOTES: 1. Set the TRDSTR register using the MOV instruction (do not use the bit handling instruction). Refer to 16.4.12.1 TRDSTR Register of Notes on Tim er RD. 2. When the CSEL0 bit is set to 1, w rite 0 to the TSTART0 bit. 3. When the CSEL1 bit is set to 1, w rite 0 to the TSTART1 bit. 4. When the CSEL0 bit is set to 0 and the compare match signal (TRDIOA0) is generated, this bit is set to 0 (count stops). 5. When the CSEL1 bit is set to 0 and the compare match signal (TRDIOA1) is generated, this bit is set to 0 (count stops). Timer RD Mode Register b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRDMR Bit Symbol Address 0138h Bit Name Timer RD synchronous bit SYNC -- (b3-b1) After Reset 00001110b Function 0 : Registers TRD0 and TRD1 operate independently 1 : Registers TRD0 and TRD1 operate synchronously RW Nothing is assigned. If necessary, set to 0. When read, the content is 1. -- BFC0 TRDGRC0 register function select bit 0 : General register 1 : Buffer register of TRDGRA0 register RW BFD0 TRDGRD0 register function select bit 0 : General register 1 : Buffer register of TRDGRB0 register RW BFC1 TRDGRC1 register function select bit 0 : General register 1 : Buffer register of TRDGRA1 register RW BFD1 TRDGRD1 register function select bit 0 : General register 1 : Buffer register of TRDGRB1 register RW Figure 16.100 Registers TRDSTR and TRDMR in PWM Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 RW Page 260 of 450 R8C/2K Group, R8C/2L Group 16. Timers Timer RD PWM Mode Register b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRDPMR Bit Symbol PWMB0 PWMC0 PWMD0 -- (b3) PWMB1 PWMC1 PWMD1 -- (b7) Address 0139h Bit Name PWM mode of TRDIOB0 select bit RW 0 : Timer mode 1 : PWM mode RW PWM mode of TRDIOC0 select bit 0 : Timer mode 1 : PWM mode RW PWM mode of TRDIOD0 select bit 0 : Timer mode 1 : PWM mode RW Nothing is assigned. If necessary, set to 0. When read, the content is 1. -- PWM mode of TRDIOB1 select bit 0 : Timer mode 1 : PWM mode RW PWM mode of TRDIOC1 select bit 0 : Timer mode 1 : PWM mode RW PWM mode of TRDIOD1 select bit 0 : Timer mode 1 : PWM mode RW Nothing is assigned. If necessary, set to 0. When read, the content is 1. Figure 16.101 TRDPMR Register in PWM Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 After Reset 10001000b Function Page 261 of 450 -- R8C/2K Group, R8C/2L Group 16. Timers Timer RD Function Control Register b7 b6 b5 b4 b3 b2 b1 b0 1 0 0 Symbol TRDFCR Bit Symbol CMD0 Address 013Ah Bit Name Combination mode select bits (1) After Reset 10000000b Function Set to 00b (timer mode, PWM mode, or PWM3 mode) in PWM mode. CMD1 RW RW OLS0 Normal-phase output level select Bit This bit is disabled in PWM mode. (in reset synchronous PWM mode or complementary PWM mode) RW OLS1 Counter-phase output level select bit This bit is disabled in PWM mode. (in reset synchronous PWM mode or complementary PWM mode) RW ADTRG A/D trigger enable bit (in complementary PWM mode) This bit is disabled in PWM mode. ADEG A/D trigger edge select bit (in complementary PWM mode) This bit is disabled in PWM mode. External clock input select bit 0 : External clock input disabled 1 : External clock input enabled RW PWM3 mode select bit(2) Set this bit to 1 (other than PWM3 mode) in PWM mode. RW STCLK PWM3 NOTES: 1. Set bits CMD1 to CMD0 w hen both the TSTART0 and TSTART1 bits are set to 0 (count stops). 2. When bits CMD1 to CMD0 are set to 00b (timer mode, PWM mode, or PWM3 mode), the setting of the PWM3 bit is enabled. Figure 16.102 TRDFCR Register in PWM Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 RW Page 262 of 450 RW RW R8C/2K Group, R8C/2L Group 16. Timers Timer RD Output Master Enable Register 1 b7 b6 b5 b4 b3 b2 b1 b0 1 1 Symbol TRDOER1 Bit Symbol Address 013Bh Bit Name TRDIOA0 output disable bit EA0 TRDIOB0 output disable bit EB0 TRDIOC0 output disable bit EC0 TRDIOD0 output disable bit ED0 TRDIOA1 output disable bit EA1 TRDIOB1 output disable bit EB1 TRDIOC1 output disable bit EC1 TRDIOD1 output disable bit ED1 After Reset FFh Function 0 : Enable output 1 : Disable output (The TRDIOA0 pin is used as a programmable I/O port.) RW RW 0 : Enable output 1 : Disable output (The TRDIOB0 pin is used as a programmable I/O port.) RW 0 : Enable output 1 : Disable output (The TRDIOC0 pin is used as a programmable I/O port.) RW 0 : Enable output 1 : Disable output (The TRDIOD0 pin is used as a programmable I/O port.) RW 0 : Enable output 1 : Disable output (The TRDIOA1 pin is used as a programmable I/O port.) RW 0 : Enable output 1 : Disable output (The TRDIOB1 pin is used as a programmable I/O port.) RW 0 : Enable output 1 : Disable output (The TRDIOC1 pin is used as a programmable I/O port.) RW 0 : Enable output 1 : Disable output (The TRDIOD1 pin is used as a programmable I/O port.) RW Timer RD Output Master Enable Register 2 b7 b6 b5 b4 b3 b2 b1 b0 Symbol Address 013Ch TRDOER2 Bit Symbol Bit Name -- Nothing is assigned. If necessary, set to 0. (b6-b0) When read, the content is 1. After Reset 01111111b Function RW -- _____ PTO INT0 of pulse output forced 0 : Pulse output forced cutoff input disabled cutoff signal input enabled bit(1) 1 : Pulse output forced cutoff input enabled (All bits in the TRDOER1 register are set to 1 (disable output) w hen "L" is _____ applied to the INT0 pin.) NOTE: 1. Refer to 16.4.4 Pulse Output Forced Cutoff. Figure 16.103 Registers TRDOER1 to TRDOER2 in PWM Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 263 of 450 RW R8C/2K Group, R8C/2L Group 16. Timers Timer RD Output Control Register(1) b7 b6 b5 b4 b3 b2 b1 b0 0 0 Symbol TRDOCR Bit Symbol TOA0 TOB0 TOC0 TOD0 TOA1 TOB1 TOC1 TOD1 Address 013Dh Bit Name TRDIOA0 output level select bit After Reset 00h Function Set this bit to 0 (enable output) in PWM mode. RW TRDIOB0 output level select bit(2) TRDIOC0 initial output level select bit(2) TRDIOD0 initial output level select bit(2) TRDIOA1 initial output level select bit 0 : Initial output is inactive level 1 : Initial output is active level RW RW RW Set this bit to 0 (enable output) in PWM mode. RW TRDIOB1 initial output level select bit(2) TRDIOC1 initial output level select bit(2) TRDIOD1 initial output level select bit(2) 0 : Inactive level 1 : Active level RW RW RW RW NOTES: 1. Write to the TRDOCR register w hen both the TSTART0 and TSTART1 bits in the TRDSTR register are set to 0 (count stops). 2. If the pin function is set for w aveform output (refer to Tables 16.27 to 16.29 and Tables 16.31 to 16.33), the initial output level is output w hen the TRDOCR register is set. Timer RD Control Register i (i = 0 or 1) b7 b6 b5 b4 b3 b2 b1 b0 0 0 1 Symbol TRDCR0 TRDCR1 Bit Symbol Address 0140h 0150h Bit Name Count source select bits Function TCK1 TCK2 External clock edge select bits (2) CKEG1 TRDi counter clear select bits 0 0 1 1 0 0 1 1 0 : f1 1 : f2 0 : f4 1 : f8 0 : f32 1 : TRDCLK input(1) 0 : fOCO40M 1 : Do not set. RW RW RW b4 b3 0 0 1 1 CKEG0 RW b2 b1 b0 0 0 0 0 1 1 1 1 TCK0 CCLR0 CCLR1 CCLR2 After Reset 00h 00h 0 : Count at the rising edge 1 : Count at the falling edge 0 : Count at both edges 1 : Do not set. RW RW Set to 001b (the TRDi register cleared at RW compare match w ith TRDGRAi register) in PWM RW mode. RW NOTES: 1. This setting is enabled w hen the STCLK bit in the TRDFCR register is set to 1 (external clock input enabled). 2. Bits CKEG1 to CKEG0 are enabled w hen bits TCK2 to TCK0 are set to 101b (TRDCLK input) and the STCLK bit in the TRDFCR register is set to 1 (external clock input enabled). Figure 16.104 Registers TRDOCR and TRDCR0 to TRDCR1 in PWM Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 264 of 450 R8C/2K Group, R8C/2L Group 16. Timers Timer RD Status Register i (i=0 or 1) b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRDSR0 TRDSR1 Bit Symbol IMFA Address 0143h 0153h After Reset 11100000b 11000000b Bit Name Function Input capture/compare match [Source for setting this bit to 0] flag A Write 0 after read(2). [Source for setting this bit to 1] When the value in the TRDi register matches w ith the value in the TRDGRAi register. RW IMFB Input capture/compare match [Source for setting this bit to 0] flag B Write 0 after read(2). [Source for setting this bit to 1] When the value in the TRDi register matches w ith the value in the TRDGRBi register. RW IMFC Input capture/compare match [Source for setting this bit to 0] flag C Write 0 after read(2). [Source for setting this bit to 1] When the value in the TRDi register matches w ith the value in the TRDGRCi register (3). RW IMFD Input capture/compare match [Source for setting this bit to 0] flag D Write 0 after read(2). [Source for setting this bit to 1] When the value in the TRDi register matches w ith the value in the TRDGRDi register (3). RW Overflow flag OVF UDF -- (b7-b6) Underflow flag(1) [Source for setting this bit to 0] Write 0 after read(2). [Source for setting this bit to 1] When the TRDi register overflow s. This bit is disabled in PWM mode. Nothing is assigned. If necessary, set to 0. When read, the content is 1. NOTES: 1. Nothing is assigned to b5 in the TRDSR0 register. When w riting to b5, w rite 0. When reading, the content is 1. 2. The w riting results are as follow s: * This bit is set to 0 w hen the read result is 1 and 0 is w ritten to the same bit. * This bit remains unchanged even if the read result is 0 and 0 is w ritten to the same bit. (This bit remains 1 even if it is set to 1 from 0 after reading, and w riting 0.) * This bit remains unchanged if 1 is w ritten. 3. Including w hen the BFji bit in the TRDMR register is set to 1 (TRDGRji is used as the buffer register). Figure 16.105 Registers TRDSR0 to TRDSR1 in PWM Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 RW Page 265 of 450 RW RW -- R8C/2K Group, R8C/2L Group 16. Timers Timer RD Interrupt Enable Register i (i = 0 or 1) b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRDIER0 TRDIER1 Bit Symbol IMIEA IMIEB IMIEC IMIED OVIE -- (b7-b5) Address 0144h 0154h After Reset 11100000b 11100000b Bit Name Input capture/compare match interrupt enable bit A Function 0 : Disable interrupt (IMIA) by the IMFA bit 1 : Enable interrupt (IMIA) by the IMFA bit Input capture/compare match interrupt enable bit B 0 : Disable interrupt (IMIB) by the IMFB bit 1 : Enable interrupt (IMIB) by the IMFB bit RW Input capture/compare match interrupt enable bit C 0 : Disable interrupt (IMIC) by the IMFC bit 1 : Enable interrupt (IMIC) by the IMFC bit RW Input capture/compare match interrupt enable bit D 0 : Disable interrupt (IMID) by the IMFD bit 1 : Enable interrupt (IMID) by the IMFD bit RW Overflow /underflow interrupt enable 0 : Disable interrupt (OVI) by the bit OVF bit 1 : Enable interrupt (OVI) by the OVF bit RW Nothing is assigned. If necessary, set to 0. When read, the content is 1. -- Figure 16.106 Registers TRDIER0 to TRDIER1 in PWM Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 266 of 450 RW RW R8C/2K Group, R8C/2L Group 16. Timers Timer RD PWM Mode Output Level Control Register i (i = 0 or 1) b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRDPOCR0 TRDPOCR1 Bit Symbol POLB POLC POLD -- (b7-b3) Address 0145h 0155h After Reset 11111000b 11111000b Bit Name PWM mode output level control bit B Function 0 : "L" active TRDIOBi output level is selected 1 : "H" active TRDIOBi output level is selected PWM mode output level control bit C 0 : "L" active TRDIOCi output level is selected 1 : "H" active TRDIOCi output level is selected RW PWM mode output level control bit D 0 : "L" active TRDIODi output level is selected 1 : "H" active TRDIODi output level is selected RW Nothing is assigned. If necessary, set to 0. When read, the content is 1. RW RW -- Figure 16.107 Registers TRDPOCR0 to TRDPOCR1 in PWM Mode Timer RD Counter i (i = 0 or 1)(1) (b15) b7 (b8) b0 b7 b0 Symbol TRD0 TRD1 Address 0147h-0146h 0157h-0156h Function Count a count source. Count operation is incremented. When an overflow occurs, the OVF bit in the TRDSRi register is set to 1. NOTE: 1. Access the TRDi register in 16-bit units. Do not access it in 8-bit units. Figure 16.108 Registers TRD0 to TRD1 in PWM Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 267 of 450 After Reset 0000h 0000h Setting Range 0000h to FFFFh RW RW R8C/2K Group, R8C/2L Group 16. Timers Timer RD General Registers Ai, Bi, Ci, and Di (i = 0 or 1)(1) (b15) b7 (b8) b0 b7 b0 Symbol Address After Reset TRDGRA0 TRDGRB0 TRDGRC0 TRDGRD0 TRDGRA1 TRDGRB1 TRDGRC1 TRDGRD1 0149h-0148h 014Bh-014Ah 014Dh-014Ch 014Fh-014Eh 0159h-0158h 015Bh-015Ah 015Dh-015Ch 015Fh-015Eh FFFFh FFFFh FFFFh FFFFh FFFFh FFFFh FFFFh FFFFh Function Refer to Table 16.42 TRDGRji Register Functions in PWM Mode. RW RW NOTE: 1. Access registers TRDGRAi to TRDGRDi in 16-bit units. Do not access them in 8-bit units. Figure 16.109 Registers TRDGRAi, TRDGRBi, TRDGRCi, and TRDGRDi in PWM Mode The following registers are disabled in the PWM mode: TRDDF0, TRDDF1, TRDIORA0, TRDIORC0, TRDIORA1, and TRDIORC1. Table 16.42 TRDGRji Register Functions in PWM Mode Register Setting Register Function PWM Output Pin TRDGRAi - General register. Set the PWM period TRDGRBi - General register. Set the changing point of PWM output TRDIOBi TRDGRCi BFCi = 0 General register. Set the changing point of PWM output TRDIOCi TRDGRDi BFDi = 0 TRDIODi TRDGRCi BFCi = 1 Buffer register. Set the next PWM period (Refer to 16.4.2 Buffer Operation.) TRDGRDi BFDi = 1 Buffer register. Set the changing point of the next PWM TRDIOBi output (Refer to 16.4.2 Buffer Operation.) i = 0 or 1 BFCi, BFDi: Bits in TRDMR register Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 268 of 450 - - R8C/2K Group, R8C/2L Group 16. Timers Count source Value in TRDi register m n p q m+1 n+1 m-n Active level "H" Initial output "L" to compare match TRDIOBi output Inactive level "L" p+1 TRDIOCi output Initial output "H" to compare match m-p Inactive level "H" q+1 m-q Active level "L" TRDIODi output Initial output "L" to compare match IMFA bit in TRDSRi register 1 IMFB bit in TRDSRi register 1 IMFC bit in TRDSRi register 1 IMFD bit in TRDSRi register 1 0 Set to 0 by a program Set to 0 by a program 0 0 Set to 0 by a program Set to 0 by a program 0 m: Value set in TRDGRAi register n: Value set in TRDGRBi register p: Value set in TRDGRCi register q: Value set in TRDGRDi register i = 0 or 1 The above applies under the following conditions: Bits BFCi and BFDi in the TRDMR register are set to 0 (registers TRDGRCi and TRDGRDi are not used as buffer registers). Bits EBi, ECi and EDi in the TRDOER1 register are set to 0 (enable TRDIOBi, TRDIOCi and TRDIODi pin outputs). Bits TOBi and TOCi in the TRDOCR register are set to 0 (inactive level), the TODi bit is set to 1 (active level). The POLB bit in the TRDPOCRi register is set to 1 (active level "H"), bits POLC and POLD are set to 0 (active level "L"). Figure 16.110 Operating Example of PWM Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 269 of 450 R8C/2K Group, R8C/2L Group 16. Timers Value in TRDi register p m q n 0000h TSTARTi bit in TRDSTR register 1 Since no compare match in the TRDGRBi register is generated, "L" is not applied to the TRDIOBi output 0 TRDIOBi output Duty 0% n TRDGRBi register p (p>m) q Rewrite by a program IMFA bit in TRDSRi register 1 IMFB bit in TRDSRi register 1 0 Set to 0 by a program Set to 0 by a program 0 Value in TRDi register m p n 0000h TSTARTi bit in TRDSTR register 1 When compare matches with registers TRDGRAi and TRDGRBi are generated simultaneously, the compare match with the TRDGRBi register has priority. "L" is applied to the TRDIOBi output without any change. 0 Duty 100% TRDIOBi output "L" is applied to TRDIOBi output at compare match with the TRDGRBi register with no change. TRDGRBi register n m p Rewrite by a program IMFA bit in TRDSRi register 1 IMFB bit in TRDSRi register 1 0 Set to 0 by a program Set to 0 by a program 0 i = 0 or 1 m: Value set in TRDGRAi register The above applies under the following conditions: The EBi bit in the TRDOER1 register is set to 0 (enable TRDIOBi output). The POLB bit in the TRDPOCRi register is set to 0 (active level "L"). Figure 16.111 Operating Example of PWM Mode (Duty 0%, Duty 100%) Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 270 of 450 R8C/2K Group, R8C/2L Group 16.4.8 16. Timers Reset Synchronous PWM Mode In this mode, 3 normal-phases and 3 counter-phases of the PWM waveform are output with the same period (three-phase, sawtooth wave modulation, and no dead time). Figure 16.112 shows a Block Diagram of Reset Synchronous PWM Mode, and Table 16.43 lists the Reset Synchronous PWM Mode Specifications. Figures 16.113 to 16.120 show the Registers Associated with Reset Synchronous PWM Mode and Figure 16.121 shows an Operating Example of Reset Synchronous PWM Mode. Refer to Figure 16.111 Operating Example of PWM Mode (Duty 0%, Duty 100%) for an operating example of PWM Mode with duty 0% and duty 100%. Buffer(1) Waveform control TRDGRC0 register TRDGRA0 register TRDGRD0 register TRDGRB0 register Period TRDIOC0 Normal-phase TRDIOB0 PWM1 Counter-phase TRDIOD0 Normal-phase TRDGRC1 register TRDGRA1 register TRDIOA1 PWM2 Counter-phase TRDIOC1 Normal-phase TRDGRD1 register TRDGRB1 register TRDIOB1 PWM3 Counter-phase TRDIOD1 NOTE: 1. When bits BFC0, BFD0, BFC1, and BFD1 in the TRDMR register are set to 1 (buffer register). Figure 16.112 Block Diagram of Reset Synchronous PWM Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 271 of 450 R8C/2K Group, R8C/2L Group Table 16.43 16. Timers Reset Synchronous PWM Mode Specifications Item Specification f1, f2, f4, f8, f32, fOCO40M External signal input to the TRDCLK pin (valid edge selected by a program) The TRD0 register is incremented (the TRD1 register is not used). PWM period : 1/fk x (m+1) Active level width of normal-phase : 1/fk x (m-n) Active level width of counter-phase: 1/fk x (n+1) fk:Frequency of count source m:Value set in the TRDGRA0 register n: Value set in the TRDGRB0 register (PWM1 output), Value set in the TRDGRA1 register (PWM2 output), Value set in the TRDGRB1 register (PWM3 output) Count sources Count operations PWM waveform m+1 Normal-phase m-n Counter-phase n+1 Count start condition Count stop conditions Interrupt request generation timing TRDIOA0 pin function TRDIOB0 pin function TRDIOD0 pin function TRDIOA1 pin function TRDIOC1 pin function TRDIOB1 pin function TRDIOD1 pin function TRDIOC0 pin function INT0 pin function Read from timer Write to timer Select functions 1 (count starts) is written to the TSTART0 bit in the TRDSTR register. * 0 (count stops) is written to the TSTART0 bit in the TRDSTR register when the CSEL0 bit in the TRDSTR register is set to 1. The PWM output pin holds output level before the count stops * When the CSEL0 bit in the TRDSTR register is set to 0, the count stops at the compare match in the TRDGRA0 register. The PWM output pin holds level after output change at compare match. * Compare match (the content of the TRD0 register matches content of registers TRDGRj0, TRDGRA1, and TRDGRB1). * The TRD0 register overflows Programmable I/O port or TRDCLK (external clock) input PWM1 output normal-phase output PWM1 output counter-phase output PWM2 output normal-phase output PWM2 output counter-phase output PWM3 output normal-phase output PWM3 output counter-phase output Output inverted every PWM period Programmable I/O port, pulse output forced cutoff signal input, or INT0 interrupt input The count value can be read by reading the TRD0 register. The value can be written to the TRD0 register. * The active level of normal-phase and counter-phase and initial output level selected individually. * Buffer operation (Refer to 16.4.2 Buffer Operation.) * Pulse output forced cutoff signal input (Refer to 16.4.4 Pulse Output Forced Cutoff.) j = either A, B, C, or D Rev.1.10 Dec 21, 2007 REJ09B0406-0110 (When "L" is selected as the active level) Page 272 of 450 R8C/2K Group, R8C/2L Group 16. Timers Timer RD Start Register(1) b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRDSTR Bit Symbol TSTART0 TSTART1 Address 0137h Bit Name TRD0 count start flag(4) TRD1 count start flag(5) After Reset 11111100b Function RW 0 : Count stops (2) 1 : Count starts RW 0 : Count stops (3) 1 : Count starts RW CSEL0 TRD0 count operation select bit 0 : Count stops at the compare match w ith the TRDGRA0 register 1 : Count continues after the compare match w ith the TRDGRA0 register RW CSEL1 TRD1 count operation select bit 0 : Count stops at the compare match w ith the TRDGRA1 register 1 : Count continues after the compare match w ith the TRDGRA1 register RW -- (b7-b4) Nothing is assigned. If necessary, set to 0. When read, the content is 1. -- NOTES: 1. Set the TRDSTR register using the MOV instruction (do not use the bit handling instruction). Refer to 16.4.12.1 TRDSTR Register of Notes on Tim er RD. 2. When the CSEL0 bit is set to 1, w rite 0 to the TSTART0 bit. 3. When the CSEL1 bit is set to 1, w rite 0 to the TSTART1 bit. 4. When the CSEL0 bit is set to 0 and the compare match signal (TRDIOA0) is generated, this bit is set to 0 (count stops). 5. When the CSEL1 bit is set to 0 and the compare match signal (TRDIOA1) is generated, this bit is set to 0 (count stops). Timer RD Mode Register b7 b6 b5 b4 b3 b2 b1 b0 0 Symbol TRDMR Bit Symbol Address 0138h Bit Name Timer RD synchronous bit SYNC -- (b3-b1) After Reset 00001110b Function Set this bit to 0 (registers TRD0 and TRD1 operate independently) in reset synchronous PWM mode. RW Nothing is assigned. If necessary, set to 0. When read, the content is 1. -- BFC0 TRDGRC0 register function select 0 : General register bit 1 : Buffer register of TRDGRA0 register RW BFD0 TRDGRD0 register function select 0 : General register bit 1 : Buffer register of TRDGRB0 register RW BFC1 TRDGRC1 register function select 0 : General register bit 1 : Buffer register of TRDGRA1 register RW BFD1 TRDGRD1 register function select 0 : General register bit 1 : Buffer register of TRDGRB1 register RW Figure 16.113 Registers TRDSTR and TRDMR in Reset Synchronous PWM Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 RW Page 273 of 450 R8C/2K Group, R8C/2L Group 16. Timers Timer RD Function Control Register b7 b6 b5 b4 b3 b2 b1 b0 0 1 Symbol TRDFCR Bit Symbol CMD0 Address 013Ah Bit Name Combination mode select bits (1, 2) After Reset 10000000b Function Set to 01b (reset synchronous PWM mode) in reset synchronous PWM mode. CMD1 OLS0 OLS1 RW RW Normal-phase output level select bit 0 : Initial output "H" (in reset synchronous PWM mode or Active level "L" complementary PWM mode) 1 : Initial output "L" Active level "H" Counter-phase output level select bit 0 : Initial output "H" (in reset synchronous PWM mode or Active level "L" complementary PWM mode) 1 : Initial output "L" Active level "H" RW RW ADTRG A/D trigger enable bit (in complementary PWM mode) This bit is disabled in reset synchronous PWM mode. RW ADEG A/D trigger edge select bit (in complementary PWM mode) This bit is disabled in reset synchronous PWM mode. RW External clock input select bit 0 : External clock input disabled 1 : External clock input enabled RW PWM3 mode select bit(3) This bit is disabled in reset synchronous PWM mode. RW STCLK PWM3 NOTES: 1. When bits CMD1 to CMD0 are set to 01b, 10b, or 11b, the MCU enters reset synchronous PWM mode or complementary PWM mode in spite of the setting of the TRDPMR register. 2. Set bits CMD1 to CMD0 w hen both the TSTART0 and TSTART1 bits are set to 0 (count stops). 3. When bits CMD1 to CMD0 are set to 00b (timer mode, PWM mode, or PWM3 mode), the setting of the PWM3 bit is enabled. Figure 16.114 TRDFCR Register in Reset Synchronous PWM Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 RW Page 274 of 450 R8C/2K Group, R8C/2L Group 16. Timers Timer RD Output Master Enable Register 1 b7 b6 b5 b4 b3 b2 b1 b0 1 Symbol TRDOER1 Bit Symbol Address 013Bh Bit Name TRDIOA0 output disable bit EA0 TRDIOB0 output disable bit EB0 TRDIOC0 output disable bit EC0 TRDIOD0 output disable bit ED0 TRDIOA1 output disable bit EA1 TRDIOB1 output disable bit EB1 TRDIOC1 output disable bit EC1 TRDIOD1 output disable bit ED1 After Reset FFh Function Set this bit to 1 (the TRDIOA0 pin is used as a programmable I/O port) in reset synchronous PWM mode. RW RW 0 : Enable output 1 : Disable output (The TRDIOB0 pin is used as a programmable I/O port.) RW 0 : Enable output 1 : Disable output (The TRDIOC0 pin is used as a programmable I/O port.) RW 0 : Enable output 1 : Disable output (The TRDIOD0 pin is used as a programmable I/O port.) RW 0 : Enable output 1 : Disable output (The TRDIOA1 pin is used as a programmable I/O port.) RW 0 : Enable output 1 : Disable output (The TRDIOB1 pin is used as a programmable I/O port.) RW 0 : Enable output 1 : Disable output (The TRDIOC1 pin is used as a programmable I/O port.) RW 0 : Enable output 1 : Disable output (The TRDIOD1 pin is used as a programmable I/O port.) RW Timer RD Output Master Enable Register 2 b7 b6 b5 b4 b3 b2 b1 b0 Symbol Address 013Ch TRDOER2 Bit Symbol Bit Name -- Nothing is assigned. If necessary, set to 0. (b6-b0) When read, the content is 1. After Reset 01111111b Function RW -- _____ PTO INT0 of pulse output forced 0 : Pulse output forced cutoff input disabled cutoff signal input enabled bit(1) 1 : Pulse output forced cutoff input enabled (All bits in the TRDOER1 register are set to 1 (disable output) w hen "L" is _____ applied to the INT0 pin.) NOTE: 1. Refer to 16.4.4 Pulse Output Forced Cutoff. Figure 16.115 Registers TRDOER1 to TRDOER2 in Reset Synchronous PWM Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 275 of 450 RW R8C/2K Group, R8C/2L Group 16. Timers Timer RD Control Register 0(3) b7 b6 b5 b4 b3 b2 b1 b0 0 0 1 Symbol TRDCR0 Bit Symbol Address 0140h Bit Name Count source select bits TCK1 TCK2 External clock edge select bits (2) CKEG1 TRD0 counter clear select bits 0 0 1 1 0 0 1 1 0 : f1 1 : f2 0 : f4 1 : f8 0 : f32 1 : TRDCLK input(1) 0 : fOCO40M 1 : Do not set. RW RW RW b4 b3 0 0 1 1 CKEG0 RW b2 b1b0 0 0 0 0 1 1 1 1 TCK0 CCLR0 CCLR1 CCLR2 After Reset 00h Function 0 : Count at the rising edge 1 : Count at the falling edge 0 : Count at both edges 1 : Do not set. Set to 001b (TRD0 register cleared at compare match w ith TRDGRA0 register) in reset synchronous PWM mode. RW RW RW RW RW NOTES: 1. This setting is enabled w hen the STCLK bit in the TRDFCR register is set to 1 (external clock input enabled). 2. Bits CKEG1 to CKEG0 are enabled w hen bits TCK2 to TCK0 are set to 101b (TRDCLK input) and the STCLK bit in the TRDFCR register is set to 1 (external clock input enabled). 3. The TRDCR1 register is not used in reset synchronous PWM mode. Figure 16.116 TRDCR0 Register in Reset Synchronous PWM Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 276 of 450 R8C/2K Group, R8C/2L Group 16. Timers Timer RD Status Register i (i = 0 or 1) b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRDSR0 TRDSR1 Bit Symbol IMFA Address 0143h 0153h After Reset 11100000b 11000000b Bit Name Function Input capture/compare match [Source for setting this bit to 0] flag A Write 0 after read(2). [Source for setting this bit to 1] When the value in the TRDi register matches w ith the value in the TRDGRAi register. RW IMFB Input capture/compare match [Source for setting this bit to 0] flag B Write 0 after read(2). [Source for setting this bit to 1] When the value in the TRDi register matches w ith the value in the TRDGRBi register. RW IMFC Input capture/compare match [Source for setting this bit to 0] flag C Write 0 after read(2). [Source for setting this bit to 1] When the value in the TRDi register matches w ith the value in the TRDGRCi register (3). RW IMFD Input capture/compare match [Source for setting this bit to 0] flag D Write 0 after read(2). [Source for setting this bit to 1] When the value in the TRDi register matches w ith the value in the TRDGRDi register (3). RW Overflow flag OVF UDF -- (b7-b6) Underflow flag(1) [Source for setting this bit to 0] Write 0 after read(2). [Source for setting this bit to 1] When the TRDi register overflow s. RW This bit is disabled in reset synchronous PWM mode. RW Nothing is assigned. If necessary, set to 0. When read, the content is 1. NOTES: 1. Nothing is assigned to b5 in the TRDSR0 register. When w riting to b5, w rite 0. When reading, the content is 1. 2. The w riting results are as follow s: * This bit is set to 0 w hen the read result is 1 and 0 is w ritten to the same bit. * This bit remains unchanged even if the read result is 0 and 0 is w ritten to the same bit (this bit remains 1 even if it is set to 1 from 0 after reading, and w riting 0). * This bit remains unchanged if 1 is w ritten to it. 3. Including w hen the BFji bit in the TRDMR register is set to 1 (TRDGRji is used as the buffer register). Figure 16.117 Registers TRDSR0 to TRDSR1 in Reset Synchronous PWM Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 RW Page 277 of 450 -- R8C/2K Group, R8C/2L Group 16. Timers Timer RD Interrupt Enable Register i (i = 0 or 1) b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRDIER0 TRDIER1 Bit Symbol IMIEA IMIEB IMIEC IMIED OVIE -- (b7-b5) Address 0144h 0154h After Reset 11100000b 11100000b Bit Name Input capture/compare match interrupt enable bit A Function 0 : Disable interrupt (IMIA) by the IMFA bit 1 : Enable interrupt (IMIA) by the IMFA bit RW Input capture/compare match interrupt enable bit B 0 : Disable interrupt (IMIB) by the IMFB bit 1 : Enable interrupt (IMIB) by the IMFB bit RW Input capture/compare match interrupt enable bit C 0 : Disable interrupt (IMIC) by the IMFC bit 1 : Enable interrupt (IMIC) by the IMFC bit RW Input capture/compare match interrupt enable bit D 0 : Disable interrupt (IMID) by the IMFD bit 1 : Enable interrupt (IMID) by the IMFD bit RW Overflow /underflow interrupt enable 0 : Disable interrupt (OVI) by the bit OVF bit 1 : Enable interrupt (OVI) by the OVF bit RW Nothing is assigned. If necessary, set to 0. When read, the content is 1. -- RW Figure 16.118 Registers TRDIER0 to TRDIER1 in Reset Synchronous PWM Mode Timer RD Counter 0(1, 2) (b15) b7 (b8) b0 b7 b0 Symbol TRD0 Address 0147h-0146h Function Count a count source. Count operation is incremented. When an overflow occurs, the OVF bit in the TRDSR0 register is set to 1. NOTES: 1. Access the TRD0 register in 16-bit units. Do not access it in 8-bit units. 2. The TRD1 register is not used in reset synchronous PWM mode. Figure 16.119 TRD0 Registrar in Reset Synchronous PWM Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 278 of 450 After Reset 0000h Setting Range 0000h to FFFFh RW RW R8C/2K Group, R8C/2L Group 16. Timers Timer RD General Registers Ai, Bi, Ci, and Di (i = 0 or 1)(1) (b15) b7 (b8) b0 b7 b0 Symbol Address After Reset TRDGRA0 TRDGRB0 TRDGRC0 TRDGRD0 TRDGRA1 TRDGRB1 TRDGRC1 TRDGRD1 0149h-0148h 014Bh-014Ah 014Dh-014Ch 014Fh-014Eh 0159h-0158h 015Bh-015Ah 015Dh-015Ch 015Fh-015Eh FFFFh FFFFh FFFFh FFFFh FFFFh FFFFh FFFFh FFFFh Function RW Refer to Table 16.44 TRDGRji Register Function in Reset Synchronous PWM Mode. RW NOTE: 1. Access registers TRDGRAi to TRDGRDi in 16-bit units. Do not access them in 8-bit units. Figure 16.120 Registers TRDGRAi, TRDGRBi, TRDGRCi, and TRDGRDi in Reset Synchronous PWM Mode The following registers are disabled in the reset synchronous PWM mode: TRDPMR, TRDOCR, TRDDF0, TRDDF1, TRDIORA0, TRDIORC0, TRDPOCR0, TRDIORA1, TRDIORC1, and TRDPOCR1. Table 16.44 TRDGRji Register Functions in Reset Synchronous PWM Mode Register Setting Register Function PWM Output Pin TRDGRA0 - General register. Set the PWM period. (Output inverted every PWM period and TRDIOC0 pin) TRDGRB0 - General register. Set the changing point of PWM1 output. TRDIOB0 TRDIOD0 TRDGRC0 BFC0 = 0 - TRDGRD0 BFD0 = 0 (These registers are not used in reset synchronous PWM mode.) TRDGRA1 - General register. Set the changing point of PWM2 output. TRDIOA1 TRDIOC1 TRDGRB1 - General register. Set the changing point of PWM3 output. TRDIOB1 TRDIOD1 TRDGRC1 BFC1 = 0 - TRDGRD1 BFD1 = 0 (These points are not used in reset synchronous PWM mode.) TRDGRC0 BFC0 = 1 Buffer register. Set the next PWM period. (Refer to 16.4.2 Buffer Operation.) (Output inversed every PWM period and TRDIOC0 pin) TRDGRD0 BFD0 = 1 Buffer register. Set the changing point of the next PWM1 output. (Refer to 16.4.2 Buffer Operation.) TRDIOB0 TRDIOD0 TRDGRC1 BFC1 = 1 Buffer register. Set the changing point of the next PWM2 output. (Refer to 16.4.2 Buffer Operation.) TRDIOA1 TRDIOC1 TRDGRD1 BFD1 = 1 Buffer register. Set the changing point of the next PWM3 output. (Refer to 16.4.2 Buffer Operation.) TRDIOB1 TRDIOD1 BFC0, BFD0, BFC1, BFD1: Bits in TRDMR register Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 279 of 450 R8C/2K Group, R8C/2L Group 16. Timers Count source Value in TRD0 register m n p q 0000h TSTARTi bit in TRDSTR register 1 0 m+1 m-n TRDIOB0 output n+1 TRDIOD0 output m-p TRDIOA1 output p+1 TRDIOC1 output m-q TRDIOB1 output Initial output "H" q+1 Active level "L" TRDIOD1 output Active level "L" TRDIOC0 output Initial output "H" IMFA bit in TRDSR0 register 1 IMFB bit in TRDSR0 register 1 IMFA bit in TRDSR1 register 1 IMFB bit in TRDSR1 register 1 0 Set to 0 by a program Set to 0 by a program 0 0 Set to 0 by a program Set to 0 by a program 0 Transfer from the buffer register to the general register during buffer operation Transfer from the buffer register to the general register during buffer operation m: Value set in TRDGRA0 register n: Value set in TRDGRB0 register p: Value set in TRDGRA1 register q: Value set in TRDGRB1 register i = 0 or 1 The above applies under the following conditions: Bits OLS1 and OLS0 in the TRDFCR register are set to 0 (initial output level "H", active level "L"). Figure 16.121 Operating Example of Reset Synchronous PWM Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 280 of 450 R8C/2K Group, R8C/2L Group 16.4.9 16. Timers Complementary PWM Mode In this mode, 3 normal-phases and 3 counter-phases of the PWM waveform are output with the same period (three-phase, triangular wave modulation, and with dead time). Figure 16.122 shows a Block Diagram of Complementary PWM Mode, and Table 16.45 lists the Complementary PWM Mode Specifications. Figures 16.123 to 16.131 show the Registers Associated with Complementary PWM Mode, Figure 16.132 shows the Output Model of Complementary PWM Mode, and Figure 16.133 shows an Operating Example of Complementary PWM Mode. Buffer Waveform control TRDGRA0 register Period TRDGRB0 register PWM1 TRDIOC0 Normal-phase TRDGRD0 register Counter-phase Normal-phase TRDGRC1 register TRDGRA1 register PWM2 Counter-phase Normal-phase TRDGRD1 register TRDGRB1 register PWM3 Figure 16.122 Block Diagram of Complementary PWM Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 281 of 450 Counter-phase TRDIOB0 TRDIOD0 TRDIOA1 TRDIOC1 TRDIOB1 TRDIOD1 R8C/2K Group, R8C/2L Group Table 16.45 16. Timers Complementary PWM Mode Specifications Item Count sources Specification f1, f2, f4, f8, f32, fOCO40M External signal input to the TRDCLK pin (valid edge selected by a program) Set bits TCK2 to TCK0 in the TRDCR1 register to the same value (same count source) as bits TCK2 to TCK0 in the TRDCR0 register. Increment or decrement Registers TRD0 and TRD1 are decremented with the compare match in registers TRD0 and TRDGRA0 during increment operation. The TRD1 register value is changed from 0000h to FFFFh during decrement operation, and registers TRD0 and TRD1 are incremented. Count operations PWM operations PWM period: 1/fk x (m+2-p) x 2(1) Dead time: p Active level width of normal-phase: 1/fk x (m-n-p+1) x 2 Active level width of counter-phase: 1/fk x (n+1-p) x 2 fk: Frequency of count source m: Value set in the TRDGRA0 register n: Value set in the TRDGRB0 register (PWM1 output) Value set in the TRDGRA1 register (PWM2 output) Value set in the TRDGRB1 register (PWM3 output) p: Value set in the TRD0 register m+2-p n+1 Normal-phase Counter-phase n+1-p Count start condition Count stop conditions Interrupt request generation timing p m-p-n+1 (When "L" is selected as the active level) 1 (count starts) is written to bits TSTART0 and TSTART1 in the TRDSTR register. 0 (count stops) is written to bits TSTART0 and TSTART1 in the TRDSTR register when the CSEL0 bit in the TRDSTR register is set to 1. (The PWM output pin holds output level before the count stops.) * Compare match (The content of the TRDi register matches content of the TRDGRji register.) * The TRD1 register underflows TRDIOA0 pin function TRDIOB0 pin function TRDIOD0 pin function TRDIOA1 pin function TRDIOC1 pin function TRDIOB1 pin function TRDIOD1 pin function TRDIOC0 pin function Programmable I/O port or TRDCLK (external clock) input PWM1 output normal-phase output PWM1 output counter-phase output PWM2 output normal-phase output PWM2 output counter-phase output PWM3 output normal-phase output PWM3 output counter-phase output Output inverted every 1/2 period of PWM INT0 pin function Read from timer Write to timer Select functions Programmable I/O port, pulse output forced cutoff signal input or INT0 interrupt input The count value can be read by reading the TRDi register. The value can be written to the TRDi register. * Pulse output forced cutoff signal input (Refer to 16.4.4 Pulse Output Forced Cutoff.) * The active level of normal-phase and counter-phase and initial output level selected individually * Transfer timing from the buffer register selected * A/D trigger generated i = 0 or 1, j = either A, B, C, or D NOTE: 1. After a count starts, the PWM period is fixed. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 282 of 450 R8C/2K Group, R8C/2L Group 16. Timers Timer RD Start Register(1) b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRDSTR Bit Symbol TSTART0 TSTART1 Address 0137h Bit Name TRD0 count start flag(4) TRD1 count start flag(5) After Reset 11111100b Function RW 0 : Count stops (3) 1 : Count starts RW CSEL0 TRD0 count operation select bit 0 : Count stops at the compare match w ith the TRDGRA0 register 1 : Count continues after the compare match w ith the TRDGRA0 register RW CSEL1 TRD1 count operation select bit 0 : Count stops at the compare match w ith the TRDGRA1 register 1 : Count continues after the compare match w ith the TRDGRA1 register RW -- (b7-b4) Nothing is assigned. If necessary, set to 0. When read, the content is 1. -- NOTES: 1. Set the TRDSTR register using the MOV instruction (do not use the bit handling instruction). Refer to 16.4.12.1 TRDSTR Register of Notes on Tim er RD. 2. When the CSEL0 bit is set to 1, w rite 0 to the TSTART0 bit. 3. When the CSEL1 bit is set to 1, w rite 0 to the TSTART1 bit. 4. When the CSEL0 bit is set to 0 and the compare match signal (TRDIOA0) is generated, this bit is set to 0 (count stops). 5. When the CSEL1 bit is set to 0 and the compare match signal (TRDIOA1) is generated, this bit is set to 0 (count stops). Figure 16.123 TRDSTR Register in Complementary PWM Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 RW 0 : Count stops (2) 1 : Count starts Page 283 of 450 R8C/2K Group, R8C/2L Group 16. Timers Timer RD Mode Register b7 b6 b5 b4 b3 b2 b1 b0 0 0 Symbol TRDMR Bit Symbol Address 0138h Bit Name Timer RD synchronous bit SYNC -- (b3-b1) After Reset 00001110b Function Set this bit to 0 (registers TRD0 and TRD1 operate independently) in complementary PWM mode. Nothing is assigned. If necessary, set to 0. When read, the content is 1. RW -- BFC0 TRDGRC0 register function select bit Set this bit to 0 (general register) in complementary PWM mode. RW BFD0 TRDGRD0 register function select bit 0 : General register 1 : Buffer register of TRDGRB0 register RW BFC1 TRDGRC1 register function select bit 0 : General register 1 : Buffer register of TRDGRA1 register RW BFD1 TRDGRD1 register function select bit 0 : General register 1 : Buffer register of TRDGRB1 register RW Figure 16.124 TRDMR Register in Complementary PWM Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 RW Page 284 of 450 R8C/2K Group, R8C/2L Group 16. Timers Timer RD Function Control Register b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRDFCR Bit Symbol Address 013Ah Bit Name Combination mode select bits (1,2) CMD1 OLS1 ADTRG Normal-phase output level select bit 0 : Initial output "H" (in reset synchronous PWM mode or Active level "L" complementary PWM mode) 1 : Initial output "L" Active level "H" Counter-phase output level select bit 0 : Initial output "H" (in reset synchronous PWM mode or Active level "L" complementary PWM mode) 1 : Initial output "L" Active level "H" PWM3 RW RW RW RW A/D trigger enable bit (in complementary PWM mode) 0 : Disable A/D trigger 1 : Enable A/D trigger (3) A/D trigger edge select bit (in complementary PWM mode) 0 : A/D trigger is generated at compare match betw een registers TRD0 and TRDGRA0 1 : A/D trigger is generated at underflow in the TRD1 register RW External clock input select bit 0 : External clock input disabled 1 : External clock input enabled RW PWM3 mode select bit(4) This bit is disabled in complementary PWM mode. RW ADEG STCLK RW b1 b0 1 0 : Complementary PWM mode (transfer from the buffer register to the general register at the underflow in the TRD1 register) 1 1 : Complementary PWM mode (transfer from the buffer register to the general register at the compare match w ith registers TRD0 and TRDGRA0.) Other than above : Do not set. CMD0 OLS0 After Reset 10000000b Function RW NOTES: 1. When setting bits CMD1 to CMD0 to 10b or 11b, the MCU enters complementary PWM mode in spite of the setting of the TRDPMR register. 2. Set bits CMD1 to CMD0 w hen both the TSTART0 and TSTART1 bits are set to 0 (count stops). 3. Set the ADCAP bit in the ADC0N0 register to 1 (starts by timer RD). 4. When bits CMD1 to CMD0 are set to 00b (timer mode, PWM mode, or PWM3 mode), the setting of the PWM3 bit is enabled. Figure 16.125 TRDFCR Register in Complementary PWM Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 285 of 450 R8C/2K Group, R8C/2L Group 16. Timers Timer RD Output Master Enable Register 1 b7 b6 b5 b4 b3 b2 b1 b0 1 Symbol TRDOER1 Bit Symbol Address 013Bh Bit Name TRDIOA0 output disable bit EA0 TRDIOB0 output disable bit EB0 TRDIOC0 output disable bit EC0 TRDIOD0 output disable bit ED0 TRDIOA1 output disable bit EA1 TRDIOB1 output disable bit EB1 TRDIOC1 output disable bit EC1 TRDIOD1 output disable bit ED1 After Reset FFh Function Set this bit to 1 (the TRDIOA0 pin is used as a programmable I/O port) in complementary PWM mode. RW RW 0 : Enable output 1 : Disable output (The TRDIOB0 pin is used as a programmable I/O port.) RW 0 : Enable output 1 : Disable output (The TRDIOC0 pin is used as a programmable I/O port.) RW 0 : Enable output 1 : Disable output (The TRDIOD0 pin is used as a programmable I/O port.) RW 0 : Enable output 1 : Disable output (The TRDIOA1 pin is used as a programmable I/O port.) RW 0 : Enable output 1 : Disable output (The TRDIOB1 pin is used as a programmable I/O port.) RW 0 : Enable output 1 : Disable output (The TRDIOC1 pin is used as a programmable I/O port.) RW 0 : Enable output 1 : Disable output (The TRDIOD1 pin is used as a programmable I/O port.) RW Timer RD Output Master Enable Register 2 b7 b6 b5 b4 b3 b2 b1 b0 Symbol Address 013Ch TRDOER2 Bit Symbol Bit Name -- Nothing is assigned. If necessary, set to 0. (b6-b0) When read, the content is 1. After Reset 01111111b Function RW -- _____ PTO INT0 of pulse output forced 0 : Pulse output forced cutoff input disabled cutoff signal input enabled bit(1) 1 : Pulse output forced cutoff input enabled (All bits in the TRDOER1 register are set to 1 (disable output) w hen "L" is _____ applied to the INT0 pin.) NOTE: 1. Refer to 16.4.4 Pulse Output Forced Cutoff. Figure 16.126 Registers TRDOER1 to TRDOER2 in Complementary PWM Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 286 of 450 RW R8C/2K Group, R8C/2L Group 16. Timers Timer RD Control Register i (i = 0 or 1) b7 b6 b5 b4 b3 b2 b1 b0 0 0 0 Symbol TRDCR0 TRDCR1 Bit Symbol Address 0140h 0150h Bit Name Count source select bits (2) Function TCK1 TCK2 External clock edge select bits (2,3) CKEG1 TRDi counter clear select bits 0 0 1 1 0 0 1 1 0 : f1 1 : f2 0 : f4 1 : f8 0 : f32 1 : TRDCLK input(1) 0 : fOCO40M 1 : Do not set. RW RW RW b4 b3 0 0 1 1 CKEG0 RW b2 b1 b0 0 0 0 0 1 1 1 1 TCK0 CCLR0 After Reset 00h 00h 0 : Count at the rising edge 1 : Count at the falling edge 0 : Count at both edges 1 : Do not set. Set to 000b (disable clearing (free-running operation)) in complementary PWM mode. RW RW RW CCLR1 RW CCLR2 RW NOTES: 1. This setting is enabled w hen the STCLK bit in the TRDFCR register is set to 1 (external clock input enabled). 2. Set bits TCK2 to TCK0 and bits CKEG1 to CKEG0 in registers TRDCR0 and TRDCR1 to the same values. 3. Bits CKEG1 to CKEG0 are enabled w hen bits TCK2 to TCK0 are set to 101b (TRDCLK input) and the STCLK bit in the TRDFCR register is set to 1 (external clock input enabled). Figure 16.127 Registers TRDCR0 to TRDCR1 in Complementary PWM Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 287 of 450 R8C/2K Group, R8C/2L Group 16. Timers Timer RD Status Register i (i = 0 or 1) b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRDSR0 TRDSR1 Bit Symbol Address 0143h 0153h Bit Name Input capture/compare match flag A IMFA Input capture/compare match flag B IMFB Input capture/compare match flag C IMFC Input capture/compare match flag D IMFD Overflow flag OVF Underflow flag(1) UDF -- (b7-b6) After Reset 11100000b 11000000b Function [Source for setting this bit to 0] Write 0 after read(2). [Source for setting this bit to 1] When the value in the TRDi register matches w ith the value in the TRDGRAi register. RW [Source for setting this bit to 0] Write 0 after read(2). [Source for setting this bit to 1] When the value in the TRDi register matches w ith the value in the TRDGRCi register (3). RW [Source for setting this bit to 0] Write 0 after read(2). [Source for setting this bit to 1] When the value in the TRDi register matches w ith the value in the TRDGRDi register (3). RW [Source for setting this bit to 0] Write 0 after read(2). [Source for setting this bit to 1] When the TRDi register overflow s. RW [Source for setting this bit to 0] Write 0 after read(2). [Source for setting this bit to 1] When the TRD1 register underflow s. RW Nothing is assigned. If necessary, set to 0. When read, the content is 1. 3. Including w hen the BFji bit in the TRDMR register is set to 1 (TRDGRji is used as the buffer register). Figure 16.128 Registers TRDSR0 to TRDSR1 in Complementary PWM Mode Page 288 of 450 RW [Source for setting this bit to 0] Write 0 after read(2). [Source for setting this bit to 1] When the value in the TRDi register matches w ith the value in the TRDGRBi register. NOTES: 1. Nothing is assigned to b5 in the TRDSR0 register. When w riting to b5, w rite 0. When reading, the content is 1. 2. The w riting results are as follow s: * This bit is set to 0 w hen the read result is 1 and 0 is w ritten to the same bit. * This bit remains unchanged even if the read result is 0 and 0 is w ritten to the same bit (this bit remains 1 even if it is set to 1 from 0 after reading, and w riting 0). * This bit remains unchanged if 1 is w ritten to it. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 RW -- R8C/2K Group, R8C/2L Group 16. Timers Timer RD Interrupt Enable Register i (i = 0 or 1) b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRDIER0 TRDIER1 Bit Symbol IMIEA IMIEB IMIEC IMIED OVIE -- (b7-b5) Address 0144h 0154h After Reset 11100000b 11100000b Bit Name Input capture/compare match interrupt enable bit A Function 0 : Disable interrupt (IMIA) by the IMFA bit 1 : Enable interrupt (IMIA) by the IMFA bit Input capture/compare match interrupt enable bit B 0 : Disable interrupt (IMIB) by the IMFB bit 1 : Enable interrupt (IMIB) by the IMFB bit RW Input capture/compare match interrupt enable bit C 0 : Disable interrupt (IMIC) by the IMFC bit 1 : Enable interrupt (IMIC) by the IMFC bit RW Input capture/compare match interrupt enable bit D 0 : Disable interrupt (IMID) by the IMFD bit 1 : Enable interrupt (IMID) by the IMFD bit RW Overflow /underflow interrupt enable 0 : Disable interrupt (OVI) by the bit OVF and UDF bits 1 : Enable interrupt (OVI) by the OVF and UDF bits RW Nothing is assigned. If necessary, set to 0. When read, the content is 1. -- Figure 16.129 Registers TRDIER0 to TRDIER1 in Complementary PWM Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 289 of 450 RW RW R8C/2K Group, R8C/2L Group 16. Timers Timer RD Counter 0(1) (b15) b7 (b8) b0 b7 b0 Symbol TRD0 Address 0147h-0146h Function Set the dead time. Count a count source. Count operation is incremented or decremented. When an overflow occurs, the OVF bit in the TRDSR0 register is set to 1. After Reset 0000h Setting Range 0000h to FFFFh RW RW NOTE: 1. Access the TRD0 register in 16-bit units. Do not access it in 8-bit units. Timer RD Counter 1(1) (b15) b7 (b8) b0 b7 b0 Symbol TRD1 Address 0157h-0156h Function Select 0000h. Count a count source. Count operation is incremented or decremented. When an underflow occurs, the UDF bit in the TRDSR1 register is set to 1. After Reset 0000h Setting Range 0000h to FFFFh RW RW NOTE: 1. Access the TRD1 register in 16-bit units. Do not access it in 8-bit units. Figure 16.130 Registers TRD0 to TRD1 in Complementary PWM Mode Timer RD General Registers Ai, Bi, C1, and Di (i = 0 or 1)(1, 2) (b15) b7 (b8) b0 b7 b0 Symbol TRDGRA0 TRDGRB0 TRDGRD0 TRDGRA1 TRDGRB1 TRDGRC1 TRDGRD1 Address 0149h-0148h 014Bh-014Ah 014Fh-014Eh 0159h-0158h 015Bh-015Ah 015Dh-015Ch 015Fh-015Eh After Reset FFFFh FFFFh FFFFh FFFFh FFFFh FFFFh FFFFh Function Refer to Table 16.46 TRDGRji Register Functions in Com plem entary PWM Mode . RW RW NOTES: 1. Access registers TRDGRAi to TRDGRDi in 16-bit units. Do not access them in 8-bit units. 2. The TRDGRC0 register is not used in complementary PWM mode. Figure 16.131 Registers TRDGRAi, TRDGRBi, TRDGRC1, and TRDGRDi in Complementary PWM Mode The following registers are disabled in the complementary PWM mode: TRDPMR, TRDOCR, TRDDF0, TRDDF1, TRDIORA0, TRDIORC0, TRDPOCR0, TRDIORA1, TRDIORC1, and TRDPOCR1. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 290 of 450 R8C/2K Group, R8C/2L Group Table 16.46 16. Timers TRDGRji Register Functions in Complementary PWM Mode Register Setting Register Function PWM Output Pin TRDGRA0 - General register. Set the PWM period at initialization. (Output inverted every half Setting range: Setting value or above in TRD0 register period of TRDIOC0 pin) FFFFh - TRD0 register setting value or below Do not write to this register when the TSTART0 and TSTART1 bits in the TRDSTR register are set to 1 (count starts). TRDGRB0 - General register. Set the changing point of PWM1 output at TRDIOB0 initialization. TRDIOD0 Setting range: Setting value or above in TRD0 register TRDGRA0 register - TRD0 register setting value or below Do not write to this register when the TSTART0 and TSTART1 bits in the TRDSTR register are set to 1 (count starts). TRDGRA1 - General register. Set the changing point of PWM2 output at TRDIOA1 initialization. TRDIOC1 Setting range: Setting value or above in TRD0 register TRDGRA0 register - TRD0 register setting value or below Do not write to this register when the TSTART0 and TSTART1 bits in the TRDSTR register are set to 1 (count starts). TRDGRB1 - General register. Set the changing point of PWM3 output at TRDIOB1 initialization. TRDIOD1 Setting range: Setting value or above in TRD0 register TRDGRA0 register - TRD0 register setting value or below Do not write to this register when the TSTART0 and TSTART1 bits in the TRDSTR register are set to 1 (count starts). TRDGRC0 - This register is not used in complementary PWM mode. - TRDGRD0 BFD0 = 1 Buffer register. Set the changing point of next PWM1 output. (Refer to 16.4.2 Buffer Operation.) Setting range: Setting value or above in TRD0 register TRDGRA0 register - TRD0 register setting value or below Set this register to the same value as the TRDGRB0 register for initialization. TRDIOB0 TRDIOD0 TRDGRC1 BFC1 = 1 Buffer register. Set the changing point of next PWM2 output. (Refer to 16.4.2 Buffer Operation.) Setting range: Setting value or above in TRD0 register TRDGRA0 register - TRD0 register setting value or below Set this register to the same value as the TRDGRA1 register for initialization. TRDIOA1 TRDIOC1 TRDGRD1 BFD1 = 1 Buffer register. Set the changing point of next PWM3 output. (Refer to 16.4.2 Buffer Operation.) Setting range: Setting value or above in TRD0 register TRDGRA0 register - TRD0 register setting value or below Set this register to the same value as the TRDGRB1 register for initialization. TRDIOB1 TRDIOD1 BFC0, BFD0, BFC1, BFD1: Bits in TRDMR register Since values cannot be written to the TRDGRB0, TRDGRA1, or TRDGRB1 register directly after count operation starts (prohibited item), use the TRDGRD0, TRDGRC1, or TRDGRD1 register as a buffer register. However, to write data to the TRDGRD0, TRDGRC1, or TRDGRD1 register, set bits BFD0, BFC1, and BFD1 to 0 (general register). After this, bits BFD0, BFC1, and BFD1 may be set to 1 (buffer register). Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 291 of 450 R8C/2K Group, R8C/2L Group 16. Timers Value in TRDi register Value in TRD0 register Value in TRDGRA0 register Value in TRD1 register Value in TRDGRB0 register Value in TRDGRA1 register Value in TRDGRB1 register 0000h TRDIOB0 output TRDIOD0 output TRDIOA1 output TRDIOC1 output TRDIOB1 output TRDIOD1 output TRDIOC0 output i = 0 or 1 Figure 16.132 Output Model of Complementary PWM Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 292 of 450 R8C/2K Group, R8C/2L Group 16. Timers Count source Value in TRDi register m+1 m Value in TRD0 register n Value in TRD1 register p 0000h Set to FFFFh Bits TSTART0 and TSTART1 in TRDSTR register 1 0 TRDIOB0 output Initial output "H" Active level "L" TRDIOD0 output TRDIOC0 output Initial output "H" m+2-p m-p-n+1 n+1 n+1-p p p (m-p-n+1) x 2 Width of normalphase active level UDF bit in TRDSR1 register 1 IMFA bit in TRDSR0 register 1 Dead time n+1-p (n+1-p) x 2 Width of counter-phase active level 0 Set to 0 by a program 0 TRDGRB0 register n n Transfer (when bits CMD1 to CMD0 are set to 11b) TRDGRD0 register Transfer (when bits CMD1 to CMD0 are set to 10b) n Following data Modify with a program IMFB bit in TRDSR0 register 1 Set to 0 by a program Set to 0 by a program 0 CMD0, CMD1: Bits in TRDFCR register i = 0 or 1 m: Value set in TRDGRA0 register n: Value set in TRDGRB0 register p: Value set in TRD0 register The above applies under the following conditions: Bits OLS1 and OLS0 in TRDFCR are set to 0 (initial output level "H", active level "L" for normal-phase and counter-phase) Figure 16.133 Operating Example of Complementary PWM Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 293 of 450 R8C/2K Group, R8C/2L Group 16.4.9.1 16. Timers Transfer Timing from Buffer Register * Transfer from the TRDGRD0, TRDGRC1, or TRDGRD1 register to the TRDGRB0, TRDGRA1, or TRDGRB1 register. When bits CMD1 to CMD0 in the TRDFCR register are set to 10b, the content is transferred when the TRD1 register underflows. When bits CMD1 to CMD0 are set to 11b, the content is transferred at compare match between registers TRD0 and TRDGRA0. 16.4.9.2 A/D Trigger Generation Compare match between registers TRD0 and TRDGRA0 and TRD1 underflow can be used as the conversion start trigger of the A/D converter. The trigger is selected by bits ADEG and ADTRG in the TRDFCR register. Also, set the ADCAP bit in the ADCON0 register to 1 (starts by timer RD). Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 294 of 450 R8C/2K Group, R8C/2L Group 16. Timers 16.4.10 PWM3 Mode In this mode, 2 PWM waveforms are output with the same period. Figure 16.134 shows a Block Diagram of PWM3 Mode, and Table 16.47 lists the PWM3 Mode Specifications. Figures 16.135 to 16.144 show the Registers Associated with PWM3 Mode, and Figure 16.145 shows an Operating Example of PWM3 Mode. Buffer Compare match signal TRD0 TRDIOA0 Output control Comparator TRDGRA0 TRDGRC0 Comparator TRDGRA1 TRDGRC1 Comparator TRDGRB0 TRDGRD0 Comparator TRDGRB1 TRDGRD1 Compare match signal Compare match signal TRDIOB0 Output control Compare match signal Figure 16.134 Block Diagram of PWM3 Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 295 of 450 R8C/2K Group, R8C/2L Group Table 16.47 16. Timers PWM3 Mode Specifications Item Specification Count sources f1, f2, f4, f8, f32, fOCO40M Count operations The TRD0 register is incremented (the TRD1 is not used). PWM waveform PWM period: 1/fk x (m+1) Active level width of TRDIOA0 output: 1/fk x (m-n) Active level width of TRDIOB0 output: 1/fk x (p-q) fk: Frequency of count source m: Value set in the TRDGRA0 register n: Value set in the TRDGRA1 register p: Value set in the TRDGRB0 register q: Value set in the TRDGRB1 register m+1 n+1 p+1 q+1 TRDIOA0 output m-n TRDIOB0 output p-q (When "H" is selected as the active level) Count start condition 1 (count starts) is written to the TSTART0 bit in the TRDSTR register. Count stop conditions * 0 (count stops) is written to the TSTART0 bit in the TRDSTR register when the CSEL0 bit in the TRDSTR register is set to 1. The PWM output pin holds output level before the count stops * When the CSEL0 bit in the TRDSTR register is set to 0, the count stops at compare match with the TRDGRA0 register. The PWM output pin holds level after output change by compare match. Interrupt request generation timing * Compare match (The content of the TRDi register matches content of the TRDGRji register.) * The TRD0 register overflows TRDIOA0, TRDIOB0 pin functions PWM output TRDIOC0, TRDIOD0, TRDIOA1 to TRDIOD1 pin functions Programmable I/O port INT0 pin function Programmable I/O port, pulse output forced cutoff signal input, or INT0 interrupt input Read from timer The count value can be read by reading the TRD0 register. Write to timer The value can be written to the TRD0 register. Select functions * Pulse output forced cutoff signal input (Refer to 16.4.4 Pulse Output Forced Cutoff.) * Buffer Operation (Refer to 16.4.2 Buffer Operation.) * Active level selectable by pin i = 0 or 1, j = either A, B, C, or D Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 296 of 450 R8C/2K Group, R8C/2L Group 16. Timers Timer RD Start Register(1) b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRDSTR Bit Symbol Address 0137h Bit Name TRD0 count start flag(4) After Reset 11111100b Function RW TRD1 count start flag(5) 0 : Count stops (3) 1 : Count starts RW TRD0 count operation select bit CSEL0 0 : Count stops at the compare match w ith the TRDGRA0 register 1 : Count continues after the compare match w ith the TRDGRA0 register RW CSEL1 TRD1 count operation select bit 0 : Count stops at the compare match [this bit is not used in PWM3 mode] w ith the TRDGRA1 register 1 : Count continues after the compare match w ith the TRDGRA1 register RW -- (b7-b4) Nothing is assigned. If necessary, set to 0. When read, the content is 1. -- TSTART0 TSTART1 NOTES: 1. Set the TRDSTR register using the MOV instruction (do not use the bit handling instruction). Refer to 16.4.12.1 TRDSTR Register of Notes on Tim er RD. 2. When the CSEL0 bit is set to 1, w rite 0 to the TSTART0 bit. 3. When the CSEL1 bit is set to 1, w rite 0 to the TSTART1 bit. 4. When the CSEL0 bit is set to 0 and the compare match signal (TRDIOA0) is generated, this bit is set to 0 (count stops). 5. When the CSEL1 bit is set to 0 and the compare match signal (TRDIOA1) is generated, this bit is set to 0 (count stops). Figure 16.135 TRDSTR Register in PWM3 Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 RW 0 : Count stops (2) 1 : Count starts Page 297 of 450 R8C/2K Group, R8C/2L Group 16. Timers Timer RD Mode Register b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRDMR Bit Symbol SYNC Address 0138h Bit Name Timer RD synchronous bit RW RW Nothing is assigned. If necessary, set to 0. When read, the content is 1. -- BFC0 TRDGRC0 register function select 0 : General register bit 1 : Buffer register of TRDGRA0 register RW BFD0 TRDGRD0 register function select 0 : General register bit 1 : Buffer register of TRDGRB0 register RW BFC1 TRDGRC1 register function select 0 : General register bit 1 : Buffer register of TRDGRA1 register RW BFD1 TRDGRD1 register function select 0 : General register bit 1 : Buffer register of TRDGRB1 register RW -- (b3-b1) Figure 16.136 TRDMR Register in PWM3 Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 After Reset 00001110b Function Set this bit to 0 (TRD0 and TRD1 operate independently) in PWM3 mode. Page 298 of 450 R8C/2K Group, R8C/2L Group 16. Timers Timer RD Function Control Register b7 b6 b5 b4 b3 b2 b1 b0 0 0 0 0 Symbol TRDFCR Bit Symbol CMD0 Address 013Ah Bit Name Combination mode select bits (1) After Reset 10000000b Function Set to 00b (timer mode, PWM mode, or PWM3 mode) in PWM3 mode. CMD1 RW RW This bit is disabled in PWM3 mode. OLS0 Normal-phase output level select bit (enabled in reset synchronous PWM mode or complementary PWM mode) This bit is disabled in PWM3 mode. OLS1 Counter-phase output level select bit (enabled in reset synchronous PWM mode or complementary PWM mode) RW RW ADTRG A/D trigger enable bit This bit is disabled in PWM3 mode. (enabled in complementary PWM mode) RW ADEG A/D trigger edge select bit This bit is disabled in PWM3 mode. (enabled in complementary PWM mode) RW STCLK PWM3 External clock input select bit Set this bit to 0 (external clock input disabled) in PWM3 mode. RW PWM3 mode select bit(2) Set this bit to 0 (PWM3 mode) in PWM3 mode. RW NOTES: 1. Set bits CMD1 to CMD0 w hen both the TSTART0 and TSTART1 bits are set to 0 (count stops). 2. When bits CMD1 to CMD0 are set to 00b (timer mode, PWM mode, or PWM3 mode), the setting of the PWM3 bit is enabled. Figure 16.137 TRDFCR Register in PWM3 Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 RW Page 299 of 450 R8C/2K Group, R8C/2L Group 16. Timers Timer RD Output Master Enable Register 1 b7 b6 b5 b4 b3 b2 b1 b0 1 1 1 1 1 1 Symbol TRDOER1 Bit Symbol Address 013Bh Bit Name TRDIOA0 output disable bit EA0 TRDIOB0 output disable bit EB0 EC0 ED0 EA1 EB1 EC1 ED1 TRDIOC0 output disable bit TRDIOD0 output disable bit TRDIOA1 output disable bit TRDIOB1 output disable bit TRDIOC1 output disable bit TRDIOD1 output disable bit After Reset FFh Function 0 : Enable output 1 : Disable output (The TRDIOA0 pin is used as a programmable I/O port.) 0 : Enable output 1 : Disable output (The TRDIOB0 pin is used as a programmable I/O port.) Set these bits to 1 (programmable I/O port) in PWM3 mode. RW RW RW RW RW RW RW RW RW Timer RD Output Master Enable Register 2 b7 b6 b5 b4 b3 b2 b1 b0 Symbol Address 013Ch TRDOER2 Bit Symbol Bit Name -- Nothing is assigned. If necessary, set to 0. (b6-b0) When read, the content is 1. After Reset 01111111b Function RW -- _____ PTO INT0 of pulse output forced cutoff signal input enabled bit(1) 0 : Pulse output forced cutoff input disabled 1 : Pulse output forced cutoff input enabled (All bits in the TRDOER1 register are set to 1 (disable output) w hen "L" is _____ applied to the INT0 pin.) NOTE: 1. Refer to 16.4.4 Pulse Output Forced Cutoff. Figure 16.138 Registers TRDOER1 to TRDOER2 in PWM3 Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 300 of 450 RW R8C/2K Group, R8C/2L Group 16. Timers Timer RD Output Control Register(1) b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRDOCR Bit Symbol Address 013Dh Bit Name TRDIOA0 output level select bit(2) TOA0 TRDIOB0 output level select bit(2) TOB0 After Reset 00h Function 0 : Active level "H", initial output "L", output "H" at compare match w ith the TRDGRA1register, output "L" at compare match w ith the TRDGRA0 register 1 : Active level "L", initial output "H", output "L" at compare match w ith the TRDGRA1register, output "H" at compare match w ith the TRDGRA0 register 0 : Active level "H", initial output "L", output "H" at compare match w ith the TRDGRB1register, output "L" at compare match w ith the TRDGRB0 register 1 : Active level "L", initial output "H", output "L" at compare match w ith the TRDGRB1register, output "H" at compare match w ith the TRDGRB0 register These bits are disabled in PWM3 mode. RW RW RW TOC0 TRDIOC0 initial output level select bit TOD0 TRDIOD0 initial output level select bit RW TOA1 TRDIOA1 initial output level select bit RW TOB1 TRDIOB1 initial output level select bit RW TOC1 TRDIOC1 initial output level select bit RW TOD1 TRDIOD1 initial output level select bit RW RW NOTES: 1. Write to the TRDOCR register w hen both bits TSTART0 and TSTART1 in the TRDSTR register are set to 0 (count stops). 2. If the pin function is set for w aveform output (refer to Tables 16.26 and 16.27), the initial output level is output w hen the TRDOCR register is set. Figure 16.139 TRDOCR Register in PWM3 Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 301 of 450 R8C/2K Group, R8C/2L Group 16. Timers Timer RD Control Register 0(2) b7 b6 b5 b4 b3 b2 b1 b0 0 0 1 Symbol TRDCR0 Bit Symbol Address 0140h Bit Name Count source select bits TCK1 TCK2 0 0 1 1 0 0 1 1 0 : f1 1 : f2 0 : f4 1 : f8 0 : f32 1 : Do not set. 0 : fOCO40M 1 : Do not set. External clock edge select bits (1) These bits are disabled in PWM3 mode. TRD0 counter clear select bits RW b2 b1b0 0 0 0 0 1 1 1 1 TCK0 CKEG0 CKEG1 CCLR0 CCLR1 CCLR2 After Reset 00h Function Set to 001b (the TRD0 register cleared at compare match w ith TRDGRA0 register) in PWM3 mode. RW RW RW RW RW RW RW RW NOTES: 1. Bits CKEG1 to CKEG0 are enabled w hen bits TCK2 to TCK0 are set to 101b (TRDCLK input) and the STCLK bit in the TRDFCR register is set to 1 (external clock input enabled). 2. The TRDCR1 register is not used in PWM3 mode. Figure 16.140 TRDCR0 Register in PWM3 Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 302 of 450 R8C/2K Group, R8C/2L Group 16. Timers Timer RD Status Register i (i = 0 or 1) b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRDSR0 TRDSR1 Bit Symbol Address 0143h 0153h Bit Name Input capture/compare match flag A IMFA Input capture/compare match flag B IMFB Input capture/compare match flag C IMFC Input capture/compare match flag D IMFD Overflow flag OVF UDF -- (b7-b6) Underflow flag(1) After Reset 11100000b 11000000b Function [Source for setting this bit to 0] Write 0 after read(1). [Source for setting this bit to 1] When the value in the TRDi register matches w ith the value in the TRDGRAi register. RW [Source for setting this bit to 0] Write 0 after read(1). [Source for setting this bit to 1] When the value in the TRDi register matches w ith the value in the TRDGRCi register (2). RW [Source for setting this bit to 0] Write 0 after read(1). [Source for setting this bit to 1] When the value in the TRDi register matches w ith the value in the TRDGRDi register (2). RW [Source for setting this bit to 0] Write 0 after read(1). [Source for setting this bit to 1] When the TRDi register overflow s. RW This bit is disabled in PWM3 mode. Nothing is assigned. If necessary, set to 0. When read, the content is 1. 2. Including w hen the BFji (j = C or D) bit in the TRDMR register is set to 1 (TRDGRji is used as the buffer register). Figure 16.141 Registers TRDSR0 to TRDSR1 in PWM3 Mode Page 303 of 450 RW [Source for setting this bit to 0] Write 0 after read(1). [Source for setting this bit to 1] When the value in the TRDi register matches w ith the value in the TRDGRBi register. NOTES: 1. The w riting results are as follow s: * This bit is set to 0 w hen the read result is 1 and 0 is w ritten to the same bit. * This bit remains unchanged even if the read result is 0 and 0 is w ritten to the same bit (this bit remains 1 even if it is set to 1 from 0 after reading, and w riting 0). * This bit remains unchanged if 1 is w ritten to it. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 RW RW -- R8C/2K Group, R8C/2L Group 16. Timers Timer RD Interrupt Enable Register i (i = 0 or 1) b7 b6 b5 b4 b3 b2 b1 b0 Symbol TRDIER0 TRDIER1 Bit Symbol IMIEA IMIEB IMIEC IMIED OVIE -- (b7-b5) Address 0144h 0154h Bit Name Input capture/compare match interrupt enable bit A After Reset 11100000b 11100000b Function 0 : Disable interrupt (IMIA) by the IMFA bit 1 : Enable interrupt (IMIA) by the IMFA bit Input capture/compare match interrupt enable bit B 0 : Disable interrupt (IMIB) by the IMFB bit 1 : Enable interrupt (IMIB) by the IMFB bit RW Input capture/compare match interrupt enable bit C 0 : Disable interrupt (IMIC) by the IMFC bit 1 : Enable interrupt (IMIC) by the IMFC bit RW Input capture/compare match interrupt enable bit D 0 : Disable interrupt (IMID) by the IMFD bit 1 : Enable interrupt (IMID) by the IMFD bit RW Overflow /underflow interrupt enable 0 : Disable interrupt (OVI) by the bit OVF bit 1 : Enable interrupt (OVI) by the OVF bit RW Nothing is assigned. If necessary, set to 0. When read, the content is 1. -- RW RW Figure 16.142 Registers TRDIER0 to TRDIER1 in PWM3 Mode Timer RD Counter 0(1, 2) (b15) b7 (b8) b0 b7 b0 Symbol TRD0 Address 0147h-0146h Function Count a count source. Count operation is incremented. When an overflow occurs, the OVF bit in the TRDSR0 register is set to 1. NOTES: 1. Access the TRD0 register in 16-bit units. Do not access it in 8-bit units. 2. The TRD1 register is not used in PWM3 mode. Figure 16.143 TRD0 Register in PWM3 Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 304 of 450 After Reset 0000h Setting Range 0000h to FFFFh RW RW R8C/2K Group, R8C/2L Group 16. Timers Timer RD General Registers Ai, Bi, Ci, and Di (i = 0 or 1)(1) (b15) b7 (b8) b0 b7 b0 Symbol TRDGRA0 TRDGRB0 TRDGRC0 TRDGRD0 TRDGRA1 TRDGRB1 TRDGRC1 TRDGRD1 Address After Reset 0149h-0148h 014Bh-014Ah 014Dh-014Ch 014Fh-014Eh 0159h-0158h 015Bh-015Ah 015Dh-015Ch 015Fh-015Eh FFFFh FFFFh FFFFh FFFFh FFFFh FFFFh FFFFh FFFFh Function Refer to Table 16.48 TRDGRji Register Functions in PWM3 Mode. RW RW NOTE: 1. Access registers TRDGRAi to TRDGRDi in 16-bit units. Do not access them in 8-bit units. Figure 16.144 Registers TRDGRAi, TRDGRBi, TRDGRCi, and TRDGRDi in PWM3 Mode The following registers are disabled in the PWM3 mode function: TRDPMR, TRDDF0, TRDDF1, TRDIORA0, TRDIORC0, TRDPOCR0, TRDIORA1, TRDIORC1, and TRDPOCR1. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 305 of 450 R8C/2K Group, R8C/2L Group Table 16.48 Register 16. Timers TRDGRji Register Functions in PWM3 Mode Setting Register Function TRDGRA0 - General register. Set the PWM period. Setting range: Value set in TRDGRA1 register or above TRDGRA1 General register. Set the changing point (the active level timing) of PWM output. Setting range: Value set in TRDGRA0 register or below TRDGRB0 General register. Set the changing point (the timing that returns to initial output level) of PWM output. Setting range: Value set in TRDGRB1 register or above Value set in TRDGRA0 register or below TRDGRB1 General register. Set the changing point (active level timing) of PWM output. Setting range: Value set in TRDGRB0 register or below TRDGRC0 BFC0 = 0 (These registers is not used in PWM3 mode.) PWM Output Pin TRDIOA0 TRDIOB0 - TRDGRC1 BFC1 = 0 TRDGRD0 BFD0 = 0 TRDGRD1 BFD1 = 0 TRDGRC0 BFC0 = 1 Buffer register. Set the next PWM period. (Refer to 16.4.2 Buffer Operation.) Setting range: Value set in TRDGRC1 register or above TRDIOA0 TRDGRC1 BFC1 = 1 Buffer register. Set the changing point of next PWM output. (Refer to 16.4.2 Buffer Operation.) Setting range: Value set in TRDGRC0 register or below TRDGRD0 BFD0 = 1 Buffer register. Set the changing point of next PWM output. (Refer to 16.4.2 Buffer Operation.) Setting range: Value set in TRDGRD1 register or above, setting value or below in TRDGRC0 register. TRDIOB0 TRDGRD1 BFD1 = 1 Buffer register. Set the changing point of next PWM output. (Refer to 16.4.2 Buffer Operation.) Setting range: Value set in TRDGRD0 register or below BFC0, BFD0, BFC1, BFD1: Bits in TRDMR register Registers TRDGRC0, TRDGRC1, TRDGRD0, and TRDGRD1 are not used in PWM3 mode. To use them as buffer registers, set bits BFC0, BFC1, BFD0, and BFD1 to 0 (general register) and write a value to the TRDGRC0, TRDGRC1, TRDGRD0, or TRDGRD1 register. After this, bits BFC0, BFC1, BFD0, and BFD1 may be set to 1 (buffer register). Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 306 of 450 R8C/2K Group, R8C/2L Group 16. Timers Count source Value in TRD0 register FFFFh m n p q 0000h TSTART0 bit in TRDSTR register 1 0 Count stop CSEL0 bit in TRDSTR register Set to 0 by a program 1 0 m+1 n+1 m-n p+1 q+1 p-q Output "H" at compare match with the TRDGRA1 register TRDIOA0 output Output "L" at compare match with the TRDGRA0 register Initial output "L" TRDIOB0 output IMFA bit in TRDSR0 register 1 0 Set to 0 by a program IMFB bit in TRDSR0 register Set to 0 by a program 1 0 Set to 0 by a program TRDGRA0 register Set to 0 by a program m m Transfer TRDGRC0 register m Transfer Following data Transfer from buffer register to general register j = either A or B Transfer from buffer register to general register m: Value set in TRDGRA0 register n: Value set in TRDGRA1 register p: Value set in TRDGRB0 register q: Value set in TRDGRB1 register The above applies under the following conditions: * Both the TOA0 and TOB0 bits in the TRDOCR register are set to 0 (initial output level "L", output "H" by compare match with the TRDGRj1 register, output "L" at compare match with the TRDGRj0 register). * The BFC0 bit in the TRDMR register is set to 1 (the TRDGRC0 register is used as the buffer register of the TRDGRA0 register). Figure 16.145 Operating Example of PWM3 Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 307 of 450 R8C/2K Group, R8C/2L Group 16. Timers 16.4.11 Timer RD Interrupt Timer RD generates the timer RD interrupt request based on 6 sources for each channel. The timer RD interrupt has 1 TRDiIC register (bits IR, and ILVL0 to ILVL2), and 1 vector for each channel. Table 16.49 lists the Registers Associated with Timer RD Interrupt, and Figure 16.146 shows a Block Diagram of Timer RD Interrupt. Table 16.49 Registers Associated with Timer RD Interrupt Timer RD Status Register Timer RD Interrupt Enable Register Timer RD Interrupt Control Register Channel 0 TRDSR0 TRDIER0 TRD0IC Channel 1 TRDSR1 TRDIER1 TRD1IC Channel i IMFA bit IMIEA bit Timer RD interrupt request (IR bit in TRDiIC register) IMFB bit IMIEB bit IMFC bit IMIEC bit IMFD bit IMIED bit UDF bit OVF bit OVIE bit i = 0 or 1 IMFA, IMFB, IMFC, IMFD, OVF, UDF: Bits in TRDSRi register IMIEA, IMIEB, IMIEC, IMIED, OVIE: Bits in TRDIER register Figure 16.146 Block Diagram of Timer RD Interrupt As with other maskable interrupts, the timer RD interrupt is controlled by the combination of the I flag, IR bit, bits ILVL0 to ILVL2, and IPL. However, since the interrupt source (timer RD interrupt) is generated by a combination of multiple interrupt request sources, the following differences from other maskable interrupts apply: * When bits in the TRDSRi register corresponding to bits set to 1 in the TRDIERi register are set to 1 (enable interrupt), the IR bit in the TRDiIC register is set to 1 (interrupt requested). * When either bits in the TRDSRi register or bits in the TRDIERi register corresponding to bits in the TRDSRi register, or both of them, are set to 0, the IR bit is set to 0 (interrupt not requested). Therefore, even though the interrupt is not acknowledged after the IR bit is set to 1, the interrupt request will not be maintained. * When the conditions of other request sources are met, the IR bit remains 1. * When multiple bits in the TRDIERi register are set to 1, which request source causes an interrupt is determined by the TRDSRi register. * Since each bit in the TRDSRi register is not automatically set to 0 even if the interrupt is acknowledged, set each bit to 0 in the interrupt routine. For information on how to set these bits to 0, refer to the descriptions of the registers used in the different modes (Figures 16.77, 16.92, 16.105, 16.117, 16.128, and 16.141). Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 308 of 450 R8C/2K Group, R8C/2L Group 16. Timers Refer to Registers TRDSR0 to TRDSR1 in each mode (Figures 16.77, 16.92, 16.105, 16.117, 16.128, and 16.141) for the TRDSRi register. Refer to Registers TRDIER0 to TRDIER1 in each mode (Figures 16.78, 16.93, 16.106, 16.118, 16.129, and 16.142) for the TRDIERi register. Refer to 12.1.6 Interrupt Control for information on the TRDiIC register and 12.1.5.2 Relocatable Vector Tables for the interrupt vectors. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 309 of 450 R8C/2K Group, R8C/2L Group 16. Timers 16.4.12 Notes on Timer RD 16.4.12.1 TRDSTR Register * Set the TRDSTR register using the MOV instruction. * When the CSELi (i = 0 to 1) is set to 0 (the count stops at compare match of registers TRDi and TRDGRAi), the count does not stop and the TSTARTi bit remains unchanged even if 0 (count stops) is written to the TSTARTi bit. * Therefore, set the TSTARTi bit to 0 to change other bits without changing the TSTARTi bit when the CSELi bit is se to 0. * To stop counting by a program, set the TSTARTi bit after setting the CSELi bit to 1. Although the CSELi bit is set to 1 and the TSTARTi bit is set to 0 at the same time (with 1 instruction), the count cannot be stopped. * Table 16.50 lists the TRDIOji (j = A, B, C, or D) Pin Output Level when Count Stops to use the TRDIOji (j = A, B, C, or D) pin with the timer RD output. Table 16.50 TRDIOji (j = A, B, C, or D) Pin Output Level when Count Stops Count Stop When the CSELi bit is set to 1, set the TSTARTi bit to 0 and the count stops. When the CSELi bit is set to 0, the count stops at compare match of registers TRDi and TRDGRAi. TRDIOji Pin Output when Count Stops Hold the output level immediately before the count stops. Hold the output level after output changes by compare match. 16.4.12.2 TRDi Register (i = 0 or 1) * When writing the value to the TRDi register by a program while the TSTARTi bit in the TRDSTR register is set to 1 (count starts), avoid overlapping with the timing for setting the TRDi register to 0000h, and then write. If the timing for setting the TRDi register to 0000h overlaps with the timing for writing the value to the TRDi register, the value is not written and the TRDi register is set to 0000h. These precautions are applicable when selecting the following by bits CCLR2 to CCLR0 in the TRDCRi register. - 001b (Clear by the TRDi register at compare match with the TRDGRAi register.) - 010b (Clear by the TRDi register at compare match with the TRDGRBi register.) - 011b (Synchronous clear) - 101b (Clear by the TRDi register at compare match with the TRDGRCi register.) - 110b (Clear by the TRDi register at compare match with the TRDGRDi register.) * When writing the value to the TRDi register and continuously reading the same register, the value before writing may be read. In this case, execute the JMP.B instruction between the writing and reading. Program example MOV.W #XXXXh, TRD0 ;Writing JMP.B L1 ;JMP.B L1: MOV.W TRD0,DATA ;Reading 16.4.12.3 TRDSRi Register (i = 0 or 1) When writing the value to the TRDSRi register and continuously reading the same register, the value before writing may be read. In this case, execute the JMP.B instruction between the writing and reading. Program example MOV.B #XXh, TRDSR0 ;Writing JMP.B L1 ;JMP.B L1: MOV.B TRDSR0,DATA ;Reading Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 310 of 450 R8C/2K Group, R8C/2L Group 16. Timers 16.4.12.4 Count Source Switch * Switch the count source after the count stops. Change procedure (1) Set the TSTARTi (i = 0 or 1) bit in the TRDSTR register to 0 (count stops). (2) Change bits TCK2 to TCK0 in the TRDCRi register. * When changing the count source from fOCO40M to another source and stopping fOCO40M, wait 2 cycles of f1 or more after setting the clock switch, and then stop fOCO40M. Change procedure (1) Set the TSTARTi (i = 0 or 1) bit in the TRDSTR register to 0 (count stops). (2) Change bits TCK2 to TCK0 in the TRDCRi register. (3) Wait 2 or more cycles of f1. (4) Set the FRA00 bit in the FRA0 register to 0 (high-speed on-chip oscillator stops). 16.4.12.5 Input Capture Function * Set the pulse width of the input capture signal to 3 or more cycles of the timer RD operation clock (refer to Table 16.25 Timer RD Operation Clocks). * The value in the TRDi register is transferred to the TRDGRji register 2 to 3 cycles of the timer RD operation clock after the input capture signal is applied to the TRDIOji pin (i = 0 or 1, j = either A, B, C, or D) (no digital filter). 16.4.12.6 Reset Synchronous PWM Mode * When reset synchronous PWM mode is used for motor control, make sure OLS0 = OLS1. * Set to reset synchronous PWM mode by the following procedure: Change procedure (1) Set the TSTART0 bit in the TRDSTR register to 0 (count stops). (2) Set bits CMD1 to CMD0 in the TRDFCR register to 00b (timer mode, PWM mode, and PWM3 mode). (3) Set bits CMD1 to CMD0 to 01b (reset synchronous PWM mode). (4) Set the other registers associated with timer RD again. 16.4.12.7 Complementary PWM Mode * When complementary PWM mode is used for motor control, make sure OLS0 = OLS1. * Change bits CMD1 to CMD0 in the TRDFCR register in the following procedure. Change procedure: When setting to complementary PWM mode (including re-set), or changing the transfer timing from the buffer register to the general register in complementary PWM mode. (1) Set both the TSTART0 and TSTART1 bits in the TRDSTR register to 0 (count stops). (2) Set bits CMD1 to CMD0 in the TRDFCR register to 00b (timer mode, PWM mode, and PWM3 mode). (3) Set bits CMD1 to CMD0 to 10b or 11b (complementary PWM mode). (4) Set the registers associated with other timer RD again. Change procedure: When stopping complementary PWM mode (1) Set both the TSTART0 and TSTART1 bits in the TRDSTR register to 0 (count stops). (2) Set bits CMD1 to CMD to 00b (timer mode, PWM mode, and PWM3 mode). * Do not write to TRDGRA0, TRDGRB0, TRDGRA1, or TRDGRB1 register during operation. When changing the PWM waveform, transfer the values written to registers TRDGRD0, TRDGRC1, and TRDGRD1 to registers TRDGRB0, TRDGRA1, and TRDGRB1 using the buffer operation. However, to write data to the TRDGRD0, TRDGRC1, or TRDGRD1 register, set bits BFD0, BFC1, and BFD1 to 0 (general register). After this, bits BFD0, BFC1, and BFD1 may be set to 1 (buffer register). The PWM period cannot be changed. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 311 of 450 R8C/2K Group, R8C/2L Group 16. Timers * If the value in the TRDGRA0 register is assumed to be m, the TRD0 register counts m-1, m, m+1, m, m-1, in that order, when changing from increment to decrement operation. When changing from m to m+1, the IMFA bit is set to 1. Also, bits CMD1 to CMD0 in the TRDFCR register are set to 11b (complementary PWM mode, buffer data transferred at compare match between registers TRD0 and TRDGRA0), the content in the buffer registers (TRDGRD0, TRDGRC1, and TRDGRD1) is transferred to the general registers (TRDGRB0, TRDGRA1, and TRDGRB1). During m+1, m, and m-1 operation, the IMFA bit remains unchanged and data are not transferred to registers such as the TRDGRA0 register. Count value in TRD0 register m+1 Setting value in TRDGRA0 register m Set to 0 by a program IMFA bit in TRDSR0 register No change 1 0 Transferred from buffer register Not transferred from buffer register When bits CMD1 to CMD0 in the TRDFCR register are set to 11b (transfer from the buffer register to the general register at compare match of between registers TRD0 and TRDGRA0). TRDGRB0 register TRDGRA1 register TRDGRB1 register Figure 16.147 Operation at Compare Match between Registers TRD0 and TRDGRA0 in Complementary PWM Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 312 of 450 R8C/2K Group, R8C/2L Group 16. Timers * The TRD1 register counts 1, 0, FFFFh, 0, 1, in that order, when changing from decrement to increment operation. The UDF bit is set to 1 when changing between 1, 0, and FFFFh operation. Also, when bits CMD1 to CMD0 in the TRDFCR register are set to 10b (complementary PWM mode, buffer data transferred at underflow in the TRD1 register), the content in the buffer registers (TRDGRD0, TRDGRC1, and TRDGRD1) is transferred to the general registers (TRDGRB0, TRDGRA1, and TRDGRB1). During FFFFh, 0, 1 operation, data are not transferred to registers such as the TRDGRB0 register. Also, at this time, the OVF bit remains unchanged. Count value in TRD0 register 1 0 FFFFh Set to 0 by a program UDF bit in TRDSR0 register 1 OVF bit in TRDSR0 register 1 0 No change 0 Transferred from buffer register TRDGRB0 register TRDGRA1 register TRDGRB1 register Not transferred from buffer register When bits CMD1 to CMD0 in the TRDFCR register are set to 10b (transfer from the buffer register to the general register when the TRD1 register underflows). Figure 16.148 Operation when TRD1 Register Underflows in Complementary PWM Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 313 of 450 R8C/2K Group, R8C/2L Group 16. Timers * Select with bits CMD1 to CMD0 the timing of data transfer from the buffer register to the general register. However, transfer takes place with the following timing in spite of the value of bits CMD1 to CMD0 in the following cases: Value in buffer register value in TRDGRA0 register: Transfer take place at underflow of the TRD1 register. After this, when the buffer register is set to 0001h or above and a smaller value than the value of the TRDGRA0 register, and the TRD1 register underflows for the first time after setting, the value is transferred to the general register. After that, the value is transferred with the timing selected by bits CMD1 to CMD0. n3 m+1 Count value in TRD0 register n2 n1 Count value in TRD1 register 0000h TRDGRD0 register n2 n1 Transfer with timing set by bits CMD1 to CMD0 n2 n1 Transfer Transfer Transfer TRDGRB0 register n2 n3 n3 Transfer at underflow of TRD1 register because of n3 > m Transfer n2 Transfer at underflow of TRD1 register because of first setting to n2 < m n1 Transfer with timing set by bits CMD1 to CMD0 TRDIOB0 output TRDIOD0 output m: Value set in TRDGRA0 register The above applies under the following conditions: * Bits CMD1 to CMD0 in the TRDFCR register are set to 11b (data in the buffer register is transferred at compare match between registers TRD0 and TRDGRA0 in complementary PWM mode). * Both the OSL0 and OLS1 bits in the TRDFCR register are set to 1 (active `H" for normal-phase and counter-phase). Figure 16.149 Operation when Value in Buffer Register Value in TRDGRA0 Register in Complementary PWM Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 314 of 450 R8C/2K Group, R8C/2L Group 16. Timers When the value in the buffer register is set to 0000h: Transfer takes place at compare match between registers TRD0 and TRDGRA0. After this, when the buffer register is set to 0001h or above and a smaller value than the value of the TRDGRA0 register, and a compare match occurs between registers TRD0 and TRDGRA0 for the first time after setting, the value is transferred to the general register. After that, the value is transferred with the timing selected by bits CMD1 to CMD0. m+1 Count value in TRD0 register n2 n1 Count value in TRD1 register 0000h 0000h n1 TRDGRD0 register Transfer Transfer TRDGRB0 register n2 n1 n1 Transfer with timing set by bits CMD1 to CMD0 Transfer 0000h Transfer at compare match between registers TRD0 and TRDGRA0 because content in TRDGRD0 register is set to 0000h. Transfer n1 Transfer at compare match between registers TRD0 and TRDGRA0 because of first setting to 0001h n1 < m Transfer with timing set by bits CMD1 to CMD0 TRDIOB0 output TRDIOD0 output m: Value set in TRDGRA0 register The above applies under the following conditions: * Bits CMD1 to CMD0 in the TRDFCR register are set to 10b (data in the buffer register is transferred at underflow of the TRD1 register in PWM mode). * Both the OLS0 and OLS1 bits in the TRDFCR register are set to 1 (active "H" for normal-phase and counter-phase). Figure 16.150 Operation when Value in Buffer Register Is Set to 0000h in Complementary PWM Mode 16.4.12.8 Count Source fOCO40M * The count source fOCO40M can be used with supply voltage VCC = 3.0 to 5.5 V. For supply voltage other than that, do not set bits TCK2 to TCK0 in registers TRDCR0 and TRDCR to 110b (select fOCO40M as the count source). Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 315 of 450 R8C/2K Group, R8C/2L Group 17. Serial Interface 17. Serial Interface The serial interface consists of two channels (UART0 or UART2). Each UARTi (i = 0 or 2) has an exclusive timer to generate the transfer clock and operates independently. Figure 17.1 shows a UARTi (i = 0 or 2) Block Diagram. Figure 17.2 shows a UARTi Transmit/Receive Unit. UARTi has two modes: clock synchronous serial I/O mode and clock asynchronous serial I/O mode (UART mode). Figures 17.3 to 17.5 show the Registers Associated with UARTi, and Figure 17.6 shows the PINSR1 Register. UARTi TXDi RXDi CLK1 to CLK0 = 00b f1 f8 f32 = 01b = 10b CKDIR = 0 Internal 1/16 Clock synchronous type U0BRG register 1/(n0+1) UART reception 1/16 Reception control circuit UART transmission Transmission control circuit Clock synchronous type External CKDIR = 1 1/2 Clock synchronous type (when internal clock is selected) Clock synchronous type (when external clock is selected) Clock synchronous type (when internal clock is selected) CLKi Receive clock Transmit clock CKDIR = 0 CKDIR = 1 CLK polarity switch circuit i = 0 or 2 CKDIR: Bit in UiMR register CLK0 to CLK1: Bits in UiC0 register Figure 17.1 UARTi (i = 0 or 2) Block Diagram Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 316 of 450 Transmit/ receive unit R8C/2K Group, R8C/2L Group 17. Serial Interface 1SP RXDi SP SP Clock synchronous type PRYE = 0 Clock PAR disabled synchronous type UART (7 bits) UART (8 bits) UART (7 bits) UARTi receive register PAR PAR UART enabled PRYE = 1 2SP UART (9 bits) Clock synchronous type UART (8 bits) UART (9 bits) 0 0 0 0 0 0 0 D8 D7 D6 D5 D4 D3 D2 D1 D0 UiRB register MSB/LSB conversion circuit Data bus high-order bits Data bus low-order bits MSB/LSB conversion circuit D8 PRYE = 1 PAR enabled 2SP SP SP UART (9 bits) UART D6 D5 D4 D3 D2 D1 TXDi Clock PAR disabled synchronous PRYE = 0 type 0 UARTi Transmit/Receive Unit Rev.1.10 Dec 21, 2007 REJ09B0406-0110 D0 UiTB register UART (8 bits) UART (9 bits) Clock synchronous type PAR 1SP Figure 17.2 D7 Page 317 of 450 UART (7 bits) UART (8 bits) Clock synchronous type UART (7 bits) UARTi transmit register i = 0 or 2 SP: Stop bit PAR: Parity bit R8C/2K Group, R8C/2L Group 17. Serial Interface UARTi Transmit/Receive Mode Register (i = 0 or 2) b7 b6 b5 b4 b3 b2 b1 b0 0 Symbol U0MR U2MR Bit Symbol Address 00A0h 0160h Bit Name Serial I/O mode select bits SMD0 SMD2 STPS Internal/external clock select bit 0 : Internal clock 1 : External clock -- (b7) RW RW RW RW Stop bit length select bit 0 : 1 stop bit 1 : 2 stop bits RW Odd/even parity select bit Enable w hen PRYE = 1 0 : Odd parity 1 : Even parity RW Parity enable bit 0 : Parity disabled 1 : Parity enabled RW Reserved bit Set to 0. PRY PRYE RW b2 b1 b0 0 0 0 : Serial interface disabled 0 0 1 : Clock synchronous serial I/O mode 1 0 0 : UART mode transfer data 7 bits long 1 0 1 : UART mode transfer data 8 bits long 1 1 0 : UART mode transfer data 9 bits long Other than above : Do not set. SMD1 CKDIR After Reset 00h 00h Function RW UARTi Bit Rate Register (i = 0 or 2)(1, 2, 3) b7 b0 Symbol U0BRG U2BRG Address 00A1h 0161h Function Assuming the set value is n, UiBRG divides the count source by n+1 NOTES: 1. Write to this register w hile the serial I/O is neither transmitting nor receiving. 2. Use the MOV instruction to w rite to this register. 3. After setting the CLK0 to CLK1 bits of the UiC0 register, w rite to the UiBRG register. Figure 17.3 Registers U0MR, U2MR and U0BRG, U2BRG Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 318 of 450 After Reset Undefined Undefined Setting Range 00h to FFh RW WO R8C/2K Group, R8C/2L Group 17. Serial Interface UARTi Transmit Buffer Register (i = 0 or 2)(1, 2) (b15) b7 (b8) b0 b7 b0 Symbol U0TB U2TB Address 00A3h-00A2h 0163h-0162h Function -- (b8-b0) Transmit data -- (b15-b9) Nothing is assigned. If necessary, set to 0. When read, the content is undefined. After Reset Undefined Undefined RW WO -- NOTES: 1. When the transfer data length is 9 bits, w rite data to high byte first, then low byte. 2. Use the MOV instruction to w rite to this register. UARTi Transmit/Receive Control Register 0 (i = 0 or 2) b7 b6 b5 b4 b3 b2 b1 b0 0 Symbol U0C0 U2C0 Bit Symbol CLK0 CLK1 -- (b2) TXEPT -- (b4) NCH Address 00A4h 0164h Bit Name BRG count source select b1 b0 0 0 : Selects f1 bits (1) 0 1 : Selects f8 1 0 : Selects f32 1 1 : Do not set. Reserved bit Set to 0. Transmit register empty flag 0 : Data in transmit register (during transmit) 1 : No data in transmit register (transmit completed) Nothing is assigned. If necessary, set to 0. When read, the content is 0. RW RW RO -- RW CLK polarity select bit 0 : Transmit data is output at falling edge of transfer clock and receive data is input at rising edge 1 : Transmit data is output at rising edge of transfer clock and receive data is input at falling edge RW Transfer format select bit 0 : LSB first 1 : MSB first Registers U0TB, U2TB and U0C0, U2C0 Rev.1.10 Dec 21, 2007 REJ09B0406-0110 RW 0 : TXDi pin is for CMOS output 1 : TXDi pin is for N-channel open-drain output NOTE: 1. If the BRG count source is sw itched, set the UiBRG register again. Figure 17.4 RW Data output select bit CKPOL UFORM After Reset 00001000b 00001000b Function Page 319 of 450 RW R8C/2K Group, R8C/2L Group 17. Serial Interface UARTi Transmit/Receive Control Register 1 (i = 0 or 2) b7 b6 b5 b4 b3 b2 b1 b0 0 Symbol U0C1 U2C1 Bit Symbol Address 00A5h 0165h Bit Name Transmit enable bit After Reset 00000010b 00000010b Function 0 : Disables transmission 1 : Enables transmission Transmit buffer empty flag 0 : Data in UiTB register 1 : No data in UiTB register RO Receive enable bit 0 : Disables reception 1 : Enables reception RW Receive complete flag(1) 0 : No data in UiRB register 1 : Data in UiRB register RO UiIRS UARTi transmit interrupt cause select bit 0 : Transmission buffer empty (TI=1) 1 : Transmission completed (TXEPT=1) RW UiRRM UARTi continuous receive mode enable bit(2) 0 : Disables continuous receive mode 1 : Enables continuous receive mode RW -- (b6) Reserved bit Set to 0. -- (b7) Nothing is assigned. If necessary, set to 0. When read, the content is 0. TE TI RE RI RW RW RW -- NOTES: 1. The RI bit is set to 0 w hen the higher byte of the UiRB register is read out. 2. Set the UiRRM bit to 0 (disables continuous receive mode) in UART mode. UARTi Receive Buffer Register (i = 0 or 2)(1) (b15) b7 (b8) b0 b7 b0 Symbol U0RB U2RB Bit Symbol -- (b7-b0) Address 00A7h-00A6h 0167h-0166h Bit Name -- -- (b8) -- (b11-b9) OER FER PER SUM -- After Reset Undefined Undefined Function Receive data (D7 to D0) Receive data (D8) Nothing is assigned. If necessary, set to 0. When read, the content is undefined. RW RO RO -- Overrun error flag(2) 0 : No overrun error 1 : Overrun error RO Framing error flag(2) 0 : No framing error 1 : Framing error RO Parity error flag(2) 0 : No parity error 1 : Parity error RO Error sum flag(2) 0 : No error 1 : Error RO NOTES: 1. Read out the UiRB register in 16-bit units. 2. Bits SUM, PER, FER, and OER are set to 0 (no error) w hen bits SMD2 to SMD0 in the UiMR register are set to 000b (serial interface disabled) or the RE bit in the UiC1 register is set to 0 (receive disabled). The SUM bit is set to 0 (no error) w hen bits PER, FER, and OER are set to 0 (no error). Bits PER and FER are set to 0 even w hen the higher byte of the UiRB register is read out. Also, bits PER and FER are set to 0 w hen reading the high-order byte of the UiRB register. Figure 17.5 Registers U0C1, U2C1 and U0RB, U2RB Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 320 of 450 R8C/2K Group, R8C/2L Group 17. Serial Interface Pin Select Register 1 b7 b0 Symbol PINSR1 Set to "70h" w hen using UART2. Do not set values other than "70h". When read, its content is undefined. Figure 17.6 PINSR1 Register Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 321 of 450 Address 00F5h Function After Reset Undefined RW WO R8C/2K Group, R8C/2L Group 17.1 17. Serial Interface Clock Synchronous Serial I/O Mode In clock synchronous serial I/O mode, data is transmitted and received using a transfer clock. Table 17.1 lists the Clock Synchronous Serial I/O Mode Specifications. Table 17.2 lists the Registers Used and Settings in Clock Synchronous Serial I/O Mode. Table 17.1 Clock Synchronous Serial I/O Mode Specifications Item Transfer data format Transfer clocks Specification * Transfer data length: 8 bits * CKDIR bit in UiMR register is set to 0 (internal clock): fi/(2(n+1)) fi = f1, f8, f32 n = value set in UiBRG register: 00h to FFh * The CKDIR bit is set to 1 (external clock): input from CLKi pin Transmit start conditions * Before transmission starts, the following requirements must be met(1) - The TE bit in the UiC1 register is set to 1 (transmission enabled) - The TI bit in the UiC1 register is set to 0 (data in the UiTB register) Receive start conditions * Before reception starts, the following requirements must be met(1) - The RE bit in the UiC1 register is set to 1 (reception enabled) - The TE bit in the UiC1 register is set to 1 (transmission enabled) - The TI bit in the UiC1 register is set to 0 (data in the UiTB register) * When transmitting, one of the following conditions can be selected - The UiIRS bit is set to 0 (transmit buffer empty): When transferring data from the UiTB register to UARTi transmit register (when transmission starts). - The UiIRS bit is set to 1 (transmission completes): When completing data transmission from UARTi transmit register. * When receiving When data transfer from the UARTi receive register to the UiRB register (when reception completes). Interrupt request generation timing Error detection Select functions * Overrun error(2) This error occurs if the serial interface starts receiving the next data item before reading the UiRB register and receives the 7th bit of the next data. * CLK polarity selection Transfer data input/output can be selected to occur synchronously with the rising or the falling edge of the transfer clock. * LSB first, MSB first selection Whether transmitting or receiving data begins with bit 0 or begins with bit 7 can be selected. * Continuous receive mode selection Receive is enabled immediately by reading the UiRB register. i = 0 or 2 NOTES: 1. If an external clock is selected, ensure that the external clock is "H" when the CKPOL bit in the UiC0 register is set to 0 (transmit data output at falling edge and receive data input at rising edge of transfer clock), and that the external clock is "L" when the CKPOL bit is set to 1 (transmit data output at rising edge and receive data input at falling edge of transfer clock). 2. If an overrun error occurs, the receive data (b0 to b8) of the UiRB register will be undefined. The IR bit in the SiRIC register remains unchanged. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 322 of 450 R8C/2K Group, R8C/2L Group Table 17.2 Register UiTB UiRB UiBRG UiMR UiC0 UiC1 17. Serial Interface Registers Used and Settings in Clock Synchronous Serial I/O Mode(1) Bit 0 to 7 0 to 7 OER 0 to 7 SMD2 to SMD0 CKDIR CLK1 to CLK0 TXEPT NCH CKPOL UFORM TE TI RE RI UiIRS UiRRM Function Set data transmission Data reception can be read Overrun error flag Set bit rate Set to 001b Select the internal clock or external clock Select the count source in the UiBRG register Transmit register empty flag Select TXDi pin output mode Select the transfer clock polarity Select the LSB first or MSB first Set this bit to 1 to enable transmission/reception Transmit buffer empty flag Set this bit to 1 to enable reception Reception complete flag Select the UARTi transmit interrupt source Set this bit to 1 to use continuous receive mode i = 0 or 2 NOTE: 1. Set bits which are not in this table to 0 when writing to the above registers in clock synchronous serial I/O mode. Table 17.3 lists the I/O Pin Functions in Clock Synchronous Serial I/O Mode. The TXDi pin outputs "H" level between the operating mode selection of UARTi (i = 0 or 2) and transfer start. (If the NCH bit is set to 1 (N-channel open-drain output), this pin is in a high-impedance state.) Table 17.3 I/O Pin Functions in Clock Synchronous Serial I/O Mode Pin Name TXD0 (P1_4) RXD0 (P1_5) Function Output serial data Input serial data CLK0 (P1_6) Output transfer clock Input transfer clock TXD2 (P0_1) RXD2 (P0_2) Output serial data Input serial data CLK2 (P0_3) Output transfer clock Input transfer clock Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Selection Method (Outputs dummy data when performing reception only) PD1_5 bit in PD1 register = 0 (P1_5 can be used as an input port when performing transmission only) CKDIR bit in U0MR register = 0 CKDIR bit in U0MR register = 1 PD1_6 bit in PD1 register = 0 (Outputs dummy data when performing reception only) PD0_2 bit in PD0 register = 0 (P0_2 can be used as an input port when performing transmission only) CKDIR bit in U2MR register = 0 CKDIR bit in U2MR register = 1 PD0_3 bit in PD0 register = 0 Page 323 of 450 R8C/2K Group, R8C/2L Group 17. Serial Interface * Example of transmit timing (when internal clock is selected) TC Transfer clock TE bit in UiC1 register 1 0 TI bit in UiC1 register 1 0 Set data in UiTB register Transfer from UiTB register to UARTi transmit register TCLK Stop pulsing because the TE bit is set to 0 CLKi D0 TXDi TXEPT bit in UiC0 register 1 0 IR bit in SiTIC register 1 0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7 Set to 0 when interrupt request is acknowledged, or set by a program TC=TCLK=2(n+1)/fi fi: Frequency of UiBRG count source (f1, f8, f32) The above applies under the following settings: n: Setting value to UiBRG register * CKDIR bit in UiMR register = 0 (internal clock) * CKPOL bit in UiC0 register = 0 (output transmit data at the falling edge and input receive data at the rising edge of the transfer clock) * UiIRS bit in UiC1 register = 0 (an interrupt request is generated when the transmit buffer is empty) * Example of receive timing (when external clock is selected) RE bit in UiC1 register 1 0 TE bit in UiC1 register 1 0 TI bit in UiC1 register 1 0 Write dummy data to UiTB register Transfer from UiTB register to UARTi transmit register 1/fEXT CLKi Receive data is taken in D0 RXDi RI bit in UiC1 register 1 0 IR bit in SiRIC register 1 0 D1 D2 D3 D4 D5 D6 D7 D0 D1 Transfer from UARTi receive register to UiRB register D2 D3 D4 D5 Read out from UiRB register Set to 0 when interrupt request is acknowledged, or set by a program The above applies under the following settings: * CKDIR bit in UiMR register = 1 (external clock) * CKPOL bit in UiC0 register = 0 (output transmit data at the falling edge and input receive data at the rising edge of the transfer clock) The following conditions are met when "H" is applied to the CLKi pin before receiving data: * TE bit in UiC1 register = 1 (enables transmit) * RE bit in UiC1 register = 1 (enables receive) * Write dummy data to the UiTB register fEXT: Frequency of external clock i = 0 or 2 Figure 17.7 Transmit and Receive Timing Example in Clock Synchronous Serial I/O Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 324 of 450 R8C/2K Group, R8C/2L Group 17.1.1 17. Serial Interface Polarity Select Function Figure 17.8 shows the Transfer Clock Polarity. Use the CKPOL bit in the UiC0 (i = 0 or 2) register to select the transfer clock polarity. * When the CKPOL bit in the UiC0 register = 0 (output transmit data at the falling edge and input receive data at the rising edge of the transfer clock) CLKi(1) TXDi D0 D1 D2 D3 D4 D5 D6 D7 RXDi D0 D1 D2 D3 D4 D5 D6 D7 * When the CKPOL bit in the UiC0 register = 1 (output transmit data at the rising edge and input receive data at the falling edge of the transfer clock) CLKi(2) TXDi D0 D1 D2 D3 D4 D5 D6 D7 RXDi D0 D1 D2 D3 D4 D5 D6 D7 NOTES: 1. When not transferring, the CLKi pin level is "H". 2. When not transferring, the CLKi pin level is "L". i = 0 or 2 Figure 17.8 17.1.2 Transfer Clock Polarity LSB First/MSB First Select Function Figure 17.9 shows the Transfer Format. Use the UFORM bit in the UiC0 (i = 0 or 2) register to select the transfer format. * When UFORM bit in UiC0 register = 0 (LSB first)(1) CLKi TXDi D0 D1 D2 D3 D4 D5 D6 D7 RXDi D0 D1 D2 D3 D4 D5 D6 D7 * When UFORM bit in UiC0 register = 1 (MSB first)(1) CLKi TXDi D7 D6 D5 D4 D3 D2 D1 D0 RXDi D7 D6 D5 D4 D3 D2 D1 D0 NOTE: 1. The above applies when the CKPOL bit in the UiC0 register is set to 0 (output transmit data at the falling edge and input receive data at the rising edge of the transfer clock). i = 0 or 2 Figure 17.9 Transfer Format Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 325 of 450 R8C/2K Group, R8C/2L Group 17.1.3 17. Serial Interface Continuous Receive Mode Continuous receive mode is selected by setting the UiRRM (i = 0 or 2) bit in the UiC1 register to 1 (enables continuous receive mode). In this mode, reading the UiRB register sets the TI bit in the UiC1 register to 0 (data in the UiTB register). When the UiRRM bit is set to 1, do not write dummy data to the UiTB register by a program. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 326 of 450 R8C/2K Group, R8C/2L Group 17.2 17. Serial Interface Clock Asynchronous Serial I/O (UART) Mode The UART mode allows data transmission and reception after setting the desired bit rate and transfer data format. Table 17.4 lists the UART Mode Specifications. Table 17.5 lists the Registers Used and Settings for UART Mode. Table 17.4 UART Mode Specifications Item Transfer data formats Transfer clocks Transmit start conditions Receive start conditions Interrupt request generation timing Error detection Specification * Character bit (transfer data): Selectable among 7, 8 or 9 bits * Start bit: 1 bit * Parity bit: Selectable among odd, even, or none * Stop bit: Selectable among 1 or 2 bits * CKDIR bit in UiMR register is set to 0 (internal clock): fj/(16(n+1)) fj = f1, f8, f32 n = value set in UiBRG register: 00h to FFh * CKDIR bit is set to 1 (external clock): fEXT/(16(n+1)) fEXT: Input from CLKi pin, n = value set in UiBRG register: 00h to FFh * Before transmission starts, the following are required - TE bit in UiC1 register is set to 1 (transmission enabled) - TI bit in UiC1 register is set to 0 (data in UiTB register) * Before reception starts, the following are required - RE bit in UiC1 register is set to 1 (reception enabled) - Start bit detected * When transmitting, one of the following conditions can be selected - UiIRS bit is set to 0 (transmit buffer empty): When transferring data from the UiTB register to UARTi transmit register (when transmission starts). - UiIRS bit is set to 1 (transfer ends): When serial interfac.e completes transmitting data from the UARTi transmit register * When receiving When transferring data from the UARTi receive register to UiRB register (when reception ends). * Overrun error(1) This error occurs if the serial interface starts receiving the next data item before reading the UiRB register and receive the bit preceding the final stop bit of the next data item. * Framing error This error occurs when the set number of stop bits is not detected. * Parity error This error occurs when parity is enabled, and the number of 1's in parity and character bits do not match the number of 1's set. * Error sum flag This flag is set is set to 1 when an overrun, framing, or parity error is generated. i = 0 or 2 NOTE: 1. If an overrun error occurs, the receive data (b0 to b8) of the UiRB register will be undefined. The IR bit in the SiRIC register remains unchanged. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 327 of 450 R8C/2K Group, R8C/2L Group Table 17.5 17. Serial Interface Registers Used and Settings for UART Mode Register UiTB 0 to 8 Set transmit data(1) UiRB 0 to 8 UiBRG UiMR OER,FER,PER,SUM 0 to 7 SMD2 to SMD0 Receive data can be read(1, 2) Error flag Set a bit rate Set to 100b when transfer data is 7 bits long Set to 101b when transfer data is 8 bits long Set to 110b when transfer data is 9 bits long Select the internal clock or external clock Select the stop bit Select whether parity is included and whether odd or even Select the count source for the UiBRG register Transmit register empty flag Select TXDi pin output mode Set to 0 LSB first or MSB first can be selected when transfer data is 8 bits long. Set to 0 when transfer data is 7 or 9 bits long. Set to 1 to enable transmit Transmit buffer empty flag Set to 1 to enable receive Receive complete flag Select the source of UARTi transmit interrupt Set to 0 UiC0 UiC1 Bit CKDIR STPS PRY, PRYE CLK0, CLK1 TXEPT NCH CKPOL UFORM TE TI RE RI UiIRS UiRRM Function i = 0 or 2 NOTES: 1. The bits used for transmit/receive data are as follows: Bits 0 to 6 when transfer data is 7 bits long; bits 0 to 7 when transfer data is 8 bits long; bits 0 to 8 when transfer data is 9 bits long. 2. The following bits are undefined: Bits 7 and 8 when transfer data is 7 bits long; bit 8 when transfer data is 8 bits long. Table 17.6 lists the I/O Pin Functions in UART Mode. After the UARTi (i = 0 or 2) operating mode is selected, the TXDi pin outputs "H" level. (If the NCH bit is set to 1 (N-channel open-drain output), this pin is in a highimpedance state) until transfer starts.) Table 17.6 I/O Pin Functions in UART Mode Pin name Function TXD0 (P1_4) Output serial data RXD0 (P1_5) Input serial data CLK0 (P1_6) TXD2 (P0_1) RXD2 (P0_2) CLK2 (P0_3) Selection Method (Cannot be used as a port when performing reception only) PD1_5 bit in PD1 register = 0 (P1_5 can be used as an input port when performing transmission only) Programmable I/O Port CKDIR bit in U0MR register = 0 Input transfer clock CKDIR bit in U0MR register = 1 PD1_6 bit in PD1 register = 0 Output serial data (Cannot be used as a port when performing reception only) Input serial data PD0_2 bit in PD0 register = 0 (P0_2 can be used as an input port when performing transmission only) Programmable I/O Port CKDIR bit in U2MR register = 0 Input transfer clock CKDIR bit in U2MR register = 1 PD0_3 bit in PD0 register = 0 Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 328 of 450 R8C/2K Group, R8C/2L Group 17. Serial Interface * Transmit timing when transfer data is 8 bits long (parity enabled, 1 stop bit) TC Transfer clock TE bit in UiC1 register 1 0 TI bit in UiC1 register 1 0 Write data to UiTB register Stop pulsing because the TE bit is set to 0 Transfer from UiTB register to UARTi transmit register Start bit TXDi ST TXEPT bit in UiC0 register 1 0 IR bit SiTIC register 1 0 Parity Stop bit bit D0 D1 D2 D3 D4 D5 D6 D7 P SP ST D0 D1 D2 D3 D4 D5 D6 D7 P SP ST D0 D1 Set to 0 when interrupt request is acknowledged, or set by a program TC=16 (n + 1) / fj or 16 (n + 1) / fEXT The above timing diagram applies under the following conditions: * PRYE bit in UiMR register = 1 (parity enabled) fj: Frequency of UiBRG count source (f1, f8, f32) * STPS bit in UiMR register = 0 (1 stop bit) fEXT: Frequency of UiBRG count source (external clock) * UiIRS bit in UiC1 register = 1 (an interrupt request is generated when transmit completes) n: Setting value to UiBRG register i = 0 or 2 * Transmit timing when transfer data is 9 bits long (parity disabled, 2 stop bits) TC Transfer clock TE bit in UiC1 register 1 0 TI bit in UiC1 register 1 0 Write data to UiTB register Transfer from UiTB register to UARTi transmit register Stop Stop bit bit Start bit TXDi ST TXEPT bit in UiC0 register 1 0 IR bit in SiTIC register 1 0 D0 D1 D2 D3 D4 D5 D6 D7 D8 SP SP ST D0 D1 D2 D3 D4 D5 D6 D7 D8 SP SP ST D0 Set to 0 when interrupt request is acknowledged, or set by a program The above timing diagram applies under the following conditions: * PRYE bit in UiMR register = 0 (parity disabled) * STPS bit in UiMR register = 1 (2 stop bits) * UiIRS bit in UiC1 register = 0 (an interrupt request is generated when transmit buffer is empty) Figure 17.10 Transmit Timing in UART Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 329 of 450 TC=16 (n + 1) / fj or 16 (n + 1) / fEXT fj: Frequency of UiBRG count source (f1, f8, f32) fEXT: Frequency of UiBRG count source (external clock) n: Setting value to UiBRG register i = 0 or 2 D1 R8C/2K Group, R8C/2L Group 17. Serial Interface * Example of receive timing when transfer data is 8 bits long (parity disabled, one stop bit) UiBRG output UiC1 register RE bit 1 0 Stop bit Start bit RXDi D0 D1 D7 Determined to be "L" Receive data taken in Transfer clock Reception triggered when transfer clock is generated by falling edge of start bit UiC1 register RI bit 1 0 SiRIC register IR bit 1 0 Transferred from UARTi receive register to UiRB register Set to 0 when interrupt request is accepted, or set by a program The above timing diagram applies when the register bits are set as follows: * UiMR register PRYE bit = 0 (parity disabled) * UiMR register STPS bit = 0 (1 stop bit) i = 0 or 2 Figure 17.11 Receive Timing Example in UART Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 330 of 450 R8C/2K Group, R8C/2L Group 17.2.1 17. Serial Interface Bit Rate In UART mode, the bit rate is the frequency divided by the UiBRG (i = 0 or 2) register. Figure 17.12 shows the Calculation Formula of UiBRG (i = 0 or 2) Register Setting Value. Table 17.7 lists the Bit Rate Setting Example in UART Mode (Internal Clock Selected). UART mode * Internal clock selected UiBRG register setting value = fj Bit Rate x 16 -1 Fj: Count source frequency of the UiBRG register (f1, f8, or f32) * External clock selected UiBRG register setting value = fEXT Bit Rate x 16 -1 fEXT: Count source frequency of the UiBRG register (external clock) i = 0 or 2 Figure 17.12 Calculation Formula of UiBRG (i = 0 or 2) Register Setting Value Table 17.7 Bit Rate Setting Example in UART Mode (Internal Clock Selected) System Clock = 20 MHz System Clock = 18.432 MHz(1) UiBRG Setting UiBRG Setting Actual Time Actual Time Setting Error Setting Error (bps) (bps) Value (%) Value (%) Bit Rate (bps) UiBRG Count Source 1200 f8 129 (81h) 1201.92 2400 f8 64 (40h) 2403.85 4800 f8 32 (20h) 4734.85 0.16 119 (77h) 0.16 -1.36 1200.00 0.00 System Clock = 8 MHz UiBRG Actual Setting Setting Time Error Value (bps) (%) 51 (33h) 1201.92 0.16 59 (3Bh) 2400.00 0.00 25 (19h) 2403.85 0.16 29 (1Dh) 4800.00 0.00 12 (0Ch) 4807.69 0.16 0.16 119 (77h) -0.22 79 (4Fh) 9600.00 0.00 51 (33h) 9615.38 14400.00 0.00 34 (22h) 14285.71 0.16 -0.79 9600 f1 129 (81h) 9615.38 14400 f1 86 (56h) 14367.82 19200 f1 64 (40h) 19230.77 0.16 59 (3Bh) 19200.00 0.00 25 (19h) 19230.77 0.16 28800 f1 42 (2Ah) 29069.77 39 (27h) 28800.00 0.00 16 (10h) 29411.76 2.12 38400 f1 32 (20h) 37878.79 0.94 -1.36 29 (1Dh) 38400.00 0.00 12 (0Ch) 38461.54 57600 f1 21 (15h) 56818.18 -1.36 19 (13h) 57600.00 0.00 0.16 -3.55 115200 f1 10 (0Ah) 113636.36 -1.36 9 (09h) 115200.00 0.00 8 (08h) 55555.56 - - - i = 0 to 1 NOTES: 1. For the high-speed on-chip oscillator, the correction value in the FRA7 register should be written into the FRA1 register. This applies when the high-speed on-chip oscillator is selected as the system clock and bits FRA22 to FRA20 in the FRA2 register are set to 000b (divide-by-2 mode). For the precision of the high-speed on-chip oscillator, refer to 22. Electrical Characteristics. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 331 of 450 R8C/2K Group, R8C/2L Group 17.3 17. Serial Interface Notes on Serial Interface * When reading data from the UiRB (i = 0 or 2) register either in the clock synchronous serial I/O mode or in the clock asynchronous serial I/O mode. Ensure the data is read in 16-bit units. When the high-order byte of the UiRB register is read, bits PER and FER in the UiRB register and the RI bit in the UiC1 register are set to 0. To check receive errors, read the UiRB register and then use the read data. Example (when reading receive buffer register): MOV.W 00A6H,R0 ; Read the U0RB register * When writing data to the UiTB register in the clock asynchronous serial I/O mode with 9-bit transfer data length, write data to the high-order byte first then the low-order byte, in 8-bit units. Example (when reading transmit buffer register): MOV.B #XXH,00A3H ; Write the high-order byte of U0TB register MOV.B #XXH,00A2H ; Write the low-order byte of U0TB register Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 332 of 450 R8C/2K Group, R8C/2L Group 18. Hardware LIN 18. Hardware LIN The hardware LIN performs LIN communication in cooperation with timer RA and UART0. 18.1 Features The hardware LIN has the features listed below. Figure 18.1 shows a Block Diagram of Hardware LIN. Master mode * Generates Synch Break * Detects bus collision Slave mode * Detects Synch Break * Measures Synch Field * Controls Synch Break and Synch Field signal inputs to UART0 * Detects bus collision NOTE: 1.The WakeUp function is detected by INT1. Hardware LIN Synch Field control circuit RXD0 pin Timer RA TIOSEL = 0 RXD data LSTART bit SBE bit LINE bit RXD0 input control circuit Timer RA underflow signal TIOSEL = 1 Bus collision detection circuit Timer RA interrupt Interrupt control circuit UART0 BCIE, SBIE, and SFIE bits UART0 transfer clock UART0 TE bit Timer RA output pulse MST bit UART0 TXD data TXD0 pin LINE, MST, SBE, LSTART, BCIE, SBIE, SFIE: Bits in LINCR register TIOSEL: Bit in TRAIOC register TE: Bit in U0C1 register Figure 18.1 Block Diagram of Hardware LIN Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 333 of 450 R8C/2K Group, R8C/2L Group 18.2 18. Hardware LIN Input/Output Pins The pin configuration of the hardware LIN is listed in Table 18.1. Table 18.1 Pin Configuration Name Abbreviation Input/Output Receive data input RXD0 Input Transmit data output TXD0 Output Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 334 of 450 Function Receive data input pin of the hardware LIN Transmit data output pin of the hardware LIN R8C/2K Group, R8C/2L Group 18.3 18. Hardware LIN Register Configuration The hardware LIN contains the registers listed below. These registers are detailed in Figures 18.2 and 18.3. * LIN Control Register 2 (LINCR2) * LIN Control Register (LINCR) * LIN Status Register (LINST) LIN Control Register 2 b7 b6 b5 b4 b3 b2 b1 b0 0 0 Symbol LINCR2 Bit Symbol Address 0105h Bit Name Bus collision during Sync Break transmission detection enable bit After Reset 00h Function 0 : Disables bus collision detection 1 : Enables bus collision detection -- (b2-b1) Reserved bits Set to 0. -- (b7-b3) Nothing is assigned. If necessary, set to 0. When read, the content is 0. -- Address 0106h Bit Name Synch Field measurementcompleted interrupt enable bit RW BCE RW RW RW LIN Control Register b7 b6 b5 b4 b3 b2 b1 b0 Symbol LINCR Bit Symbol SFIE After Reset 00h Function 0 : Disables Synch Field measurementcompleted interrupt 1 : Enables Synch Field measurementcompleted interrupt RW SBIE Synch Break detection interrupt 0 : Disables Synch Break detection interrupt enable bit 1 : Enables Synch Break detection interrupt RW BCIE Bus collision detection interrupt 0 : Disables bus collision detection interrupt enable bit 1 : Enables bus collision detection interrupt RW RXDSF LSTART SBE RXD0 input status flag 0 : RXD0 input enabled 1 : RXD0 input disabled RO Synch Break detection start bit(1) When this bit is set to 1, timer RA input is enabled and RXD0 input is disabled. When read, the content is 0. RW RXD0 input unmasking timing 0 : Unmasked after Synch Break is detected select bit (effective only in slave 1 : Unmasked after Synch Field measurement mode) is completed LIN operation mode setting bit(2) MST LINE LIN operation start bit RW 0 : Slave mode (Synch Break detection circuit actuated) 1 : Master mode (timer RA output OR'ed w ith TXD0) RW 0 : Causes LIN to stop 1 : Causes LIN to start operating(3) RW NOTES: 1. After setting the LSTART bit, confirm that the RXDSF flag is set to 1 before Synch Break input starts. 2. Before changing LIN operation modes, temporarily stop the LIN operation (LINE bit = 0). 3. Inputs to timer RA and UART0 are prohibited immediately after this bit is set to 1. (Refer to Figure 18.5 Exam ple of Header Field Transm ission Flow chart (1) and Figure 18.9 Exam ple of Header Field Reception Flow chart (2) .) Figure 18.2 Registers LINCR2 and LINCR Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 335 of 450 R8C/2K Group, R8C/2L Group 18. Hardware LIN LIN Status Register b7 b6 b5 b4 b3 b2 b1 b0 Symbol LINST Bit Symbol SFDCT SBDCT BCDCT Address 0107h Bit Name Synch Field measurementcompleted flag After Reset 00h Function 1 show s Synch Field measurement completed. Synch Break detection flag 1 show s Synch Break detected or Synch Break generation completed. Bus collision detection flag 1 show s Bus collision detected SFDCT bit clear bit When this bit is set to 1, the SFDCT bit is set to 0. When read, the content is 0. RW When this bit is set to 1, the SBDCT bit is set to 0. When read, the content is 0. RW When this bit is set to 1, the BCDCT bit is set to 0. When read, the content is 0. RW B0CLR SBDCT bit clear bit B1CLR BCDCT bit clear bit B2CLR -- (b7-b6) Figure 18.3 Nothing is assigned. If necessary, set to 0. When read, the content is 0. LINST Register Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 336 of 450 RW RO RO RO -- R8C/2K Group, R8C/2L Group 18.4 18. Hardware LIN Functional Description 18.4.1 Master Mode Figure 18.4 shows typical operation of the hardware LIN when transmitting a header field in master mode. Figures 18.5 and 18.6 show an Example of Header Field Transmission Flowchart. When transmitting a header field, the hardware LIN operates as described below. (1) When the TSTART bit in the TRACR register for timer RA is set by writing 1 in software, the hardware LIN outputs "L" level from the TXD0 pin for the period that is set in registers TRAPRE and TRA for timer RA. (2) When timer RA underflows upon reaching the terminal count, the hardware LIN reverses the output of the TXD0 pin and sets the SBDCT flag in the LINST register to 1. Furthermore, if the SBIE bit in the LINCR register is set to 1, it generates a timer RA interrupt. (3) The hardware LIN transmits 55h via UART0. (4) The hardware LIN transmits an ID field via UART0 after it finishes sending 55h. (5) The hardware LIN performs communication for a response field after it finishes sending the ID field. Synch Break TXD0 pin SBDCT flag in the LINST register IR bit in the TRAIC register Synch Field 1 0 Set by writing 1 to the B1CLR bit in the LINST register 1 0 Cleared to 0 upon acceptance of interrupt request or by a program 1 0 (1) (2) (3) The above applies under the following conditions: LINE = 1, MST = 1, SBIE = 1 Figure 18.4 IDENTIFIER Typical Operation when Sending a Header Field Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 337 of 450 (4) (5) R8C/2K Group, R8C/2L Group 18. Hardware LIN Timer RA Set to timer mode Bits TMOD0 to TMOD2 in TRAMR register 000b Timer RA Set the pulse output level from low to start TEDGSEL bit in TRAIOC register 1 Timer RA Set the INT1/TRAIO pin to P1_5 TIOSEL bit in TRAIOC register 1 Timer RA Set the count source (f1, f2, f8, fOCO) Bits TCK0 to TCK2 in TRAMR register Timer RA Set the Synch Break width TRAPRE register TRA register UART0 Set to transmit/receive mode (Transfer data length: 8 bits, Internal clock, 1 stop bit, Parity disabled) U0MR register UART0 Set the BRG count source (f1, f8, f32) U0C0CLK0 to 1 bit UART0 Set the bit rate U0BRG register For the hardware LIN function, set the TIOSEL bit in the TRAIOC register to 1. Set the count source and registers TRA and TRAPRE as suitable for the Synch Break period. Set the BRG count source and U0BRG register as appropriate for the bit rate. Hardware LIN Set the LIN operation to stop LINCR register LINE bit 0 Hardware LIN Set to master mode MST bit in LINCR register 1 Hardware LIN Set bus collision detection enabled BCE bit in LINCR2 register 1 Hardware LIN Set the LIN operation to start LINE bit in LINCR register 1 Hardware LIN Set the register to enable interrupts (Bus collision detection, Synch Break detection, Synch Field measurement) Bits BCIE, SBIE, SFIE in LINCR register Hardware LIN Clear the status flags (Bus collision detection, Synch Break detection, Synch Field measurement) Bits B2CLR, B1CLR, B0CLR in LINST register 1 A Figure 18.5 Example of Header Field Transmission Flowchart (1) Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 338 of 450 During master mode, the Synch Field measurementcompleted interrupt cannot be used. R8C/2K Group, R8C/2L Group 18. Hardware LIN A Timer RA Set the timer to start counting TSTART bit in TRACR register 1 Timer RA Read the count status flag TCSTF flag in TRACR register TCSTF = 1 ? NO YES Hardware LIN Read the Synch Break detection flag SBDCT flag in LINST register SBDCT = 1 ? NO YES Timer RA Set the timer to stop counting TSTART bit in TRACR register 0 Timer RA Read the count status flag TCSTF flag in TRACR register TCSTF = 0 ? NO YES UART0 Communication via UART0 TE bit in U0C1 register 1 U0TB register 0055h UART0 Communication via UART0 U0TB register ID field Figure 18.6 Timer RA generates Synch Break. If registers TRAPRE and TRA for timer RA do not need to be read or the register settings do not need to be changed after writing 1 to the TSTART bit, the procedure for reading TCSTF flag = 1 can be omitted. Zero to one cycle of the timer RA count source is required after timer RA starts counting before the TCSTF flag is set to 1. The timer RA interrupt may be used to terminate generation of Synch Break. Three to five cycles of the CPU clock are required after Synch Break generation completes before the SBDCT flag is set to 1. After timer RA Synch Break is generated, the timer should be made to stop counting. If registers TRAPRE and TRA for timer RA do not need to be read or the register settings do not need to be changed after writing 0 to the TSTART bit, the procedure for reading TCSTF flag = 0 can be omitted. Zero to one cycle of the timer RA count source is required after timer RA stops counting before the TCSTF flag is set to 0. Transmit the Synch Field. Transmit the ID field. Example of Header Field Transmission Flowchart (2) Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 339 of 450 R8C/2K Group, R8C/2L Group 18.4.2 18. Hardware LIN Slave Mode Figure 18.7 shows typical operation of the hardware LIN when receiving a header field in slave mode. Figure 18.8 through Figure 18.10 show an Example of Header Field Reception Flowchart. When receiving a header field, the hardware LIN operates as described below. (1) Synch Break detection is enabled by writing 1 to the LSTART bit in the LINCR register of the hardware LIN. (2) When "L" level is input for a duration equal to or greater than the period set in timer RA, the hardware LIN detects it as Synch Break. At this time, the SBDCT flag in the LINST register is set to 1. Furthermore, if the SBIE bit in the LINCR register is set to 1, the hardware LIN generates a timer RA interrupt. Then it goes to Synch Field measurement. (3) The hardware LIN receives a Synch Field (55h). At this time, it measures the period of the start bit and bits 0 to 6 by using timer RA. In this case, it is possible to select whether to input the Synch Field signal to RXD0 of UART0 by setting the SBE bit in the LINCR register accordingly. (4) The hardware LIN sets the SFDCT flag in the LINST register to 1 when it finishes measuring the Synch Field. Furthermore, if the SFIE bit in the LINCR register is set to 1, it generates a timer RA interrupt. (5) After it finishes measuring the Synch Field, calculate a transfer rate from the count value of timer RA and set to UART0 and registers TRAPRE and TRA of timer RA again. (6) The hardware LIN performs communication for a response field after it finishes receiving the ID field. Synch Break RXD0 pin 1 0 RXD0 input for UART0 1 0 RXDSF flag in the LINCR register SBDCT flag in the LINST register Synch Field IDENTIFIER Set by writing 1 to the LSTART bit in the LINCR register 1 0 Cleared to 0 when Synch Field measurement finishes Set by writing 1 to the B1CLR bit in the LINST register 1 0 Measure this period SFDCT flag in the LINST register 1 0 IR bit in the TRAIC register 1 0 Cleared to 0 upon acceptance of interrupt request or by a program (1) (2) (3) (4) The above applies under the following conditions: LINE = 1, MST = 0, SBE = 1, SBIE = 1, SFIE = 1 Figure 18.7 Typical Operation when Receiving a Header Field Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Set by writing 1 to the B0CLR bit in the LINST register Page 340 of 450 (5) (6) R8C/2K Group, R8C/2L Group 18. Hardware LIN Timer RA Set to pulse width measurement mode Bits TMOD0 to TMOD2 in the TRAMR register 011b Timer RA Set the pulse width measurement level low TEDGSEL bit in the TRAIOC register 0 Timer RA Set the INT1/TRAIO pin to P1_5 TIOSEL bit in the TRAIOC register 1 For the hardware LIN function, set the TIOSEL bit in the TRAIOC register to 1. Timer RA Set the count source (f1, f2, f8, fOCO) Bits TCK0 to TCK2 in the TRAMR register Timer RA Set the Synch Break width TRAPRE register TRA register Set the count source and registers TRA and TRAPRE as appropriate for the Synch Break period. Hardware LIN Set the LIN operation to stop LINE bit in the LINCR register 0 Hardware LIN Set to slave mode MST bit in the LINCR register 0 Hardware LIN Set the LIN operation to start LINE bit in the LINCR register 1 Hardware LIN Set the RXD0 input unmasking timing (After Synch Break detection, or after Synch Field measurement) SBE bit in the LINCR register Hardware LIN Set the register to enable interrupts (Bus collision detection, Synch Break detection, Synch Field measurement) Bits BCIE, SBIE, SFIE in the LINCR register A Figure 18.8 Example of Header Field Reception Flowchart (1) Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 341 of 450 Select the timing at which to unmask the RXD0 input for UART0. If the RXD0 input is chosen to be unmasked after detection of Synch Break, the Synch Field signal is also input to UART0. R8C/2K Group, R8C/2L Group 18. Hardware LIN A Hardware LIN Clear the status flags (Bus collision detection, Synch Break detection, Synch Field measurement) Bits B2CLR, B1CLR, B0CLR in the LINST register 1 Timer RA Set to start a pulse width measurement TSTART bit in the TRACR register 1 Timer RA waits until the timer starts counting. Timer RA Read the count status flag TCSTF flag in the TRACR register TCSTF = 1 ? NO YES Hardware LIN Set to start Synch Break detection LSTART bit in the LINCR register 1 Hardware LIN Read the RXD0 input status flag RXDSF flag in the LINCR register RXDSF = 1 ? NO YES Hardware LIN Read the Synch Break detection flag SBDCT flag in the LINST register SBDCT = 1 ? NO YES B Figure 18.9 Zero to one cycle of the timer RA count source is required after timer RA starts counting before the TCSTF flag is set to 1. Hardware LIN waits until the RXD0 input for UART0 is masked. Do not apply "L" level to the RXD pin until the RXDSF flag reads 1 after writing 1 to the LSTART bit. This is because the signal applied during this time is input directly to UART0. Three to five cycles of the CPU clock are required after the LSTART bit is set to 1 before the RXDSF flag is set to 1. After this, input to timer RA and UART0 is enabled. Hardware LIN detects a Synch Break. The interrupt of the timer RA may be used. When Synch Break is detected, timer RA is reloaded with the initially set count value. Even if the duration of the input "L" level is shorter than the set period, timer RA is reloaded with the initially set count value and waits until the next "L" level is input. Three to five cycles of the CPU clock are required after Synch Break detection before the SBDCT flag is set to 1. When the SBE bit in the LINCR register is set to 0 (unmasked after Synch Break is detected), timer RA can be used in timer mode after the SBDCT flag in the LINST register is set to 1 and the RXDSF flag is set to 0. Example of Header Field Reception Flowchart (2) Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 342 of 450 R8C/2K Group, R8C/2L Group 18. Hardware LIN B YES Hardware LIN Read the Synch Field measurementcompleted flag SFDCT flag in the LINST register SFDCT = 1 ? NO YES UART0 Set the UART0 communication rate U0BRG register Timer RA Set the Synch Break width again TRAPRE register TRA register UART0 Communication via UART0 Clock asynchronous serial interface (UART) mode Transmit ID field Figure 18.10 Example of Header Field Reception Flowchart (3) Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 343 of 450 Hardware LIN measures the Synch Field. The interrupt of timer RA may be used (the SBDCT flag is set when the timer RA counter underflows upon reaching the terminal count). When the SBE bit in the LINCR register is set to 1 (unmasked after Synch Field measurement is completed), timer RA may be used in timer mode after the SFDCT bit in the LINST register is set to 1. Set a communication rate based on the Synch Field measurement result. Communication via UART0 (The SBDCT flag is set when the timer RA counter underflows upon reaching the terminal count.) R8C/2K Group, R8C/2L Group 18.4.3 18. Hardware LIN Bus Collision Detection Function The bus collision detection function can be used when UART0 is enabled for transmission (TE bit in the U0C1 register = 1). To detect a bus collision during Synch Break transmission, set the BCE bit in the LINCR2 register to 1 (bus collision detection enabled). Figure 18.11 shows the Typical Operation when a Bus Collision is Detected. TXD0 pin 1 0 RXD0 pin 1 0 Transfer clock 1 0 LINE bit in the LINCR register 1 0 TE bit in the U0C1 register 1 0 Set to 1 by a program Set to 1 by a program BCDCT flag in the LINST register IR bit in the TRAIC register Figure 18.11 Set by writing 1 to the B2CLR bit in the LINST register 1 0 Cleared to 0 upon acceptance of interrupt request or by a program 1 0 Typical Operation when a Bus Collision is Detected Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 344 of 450 R8C/2K Group, R8C/2L Group 18.4.4 18. Hardware LIN Hardware LIN End Processing Figure 18.12 shows an Example of Hardware LIN Communication Completion Flowchart. Use the following timing for hardware LIN end processing: * If the hardware bus collision detection function is used Perform hardware LIN end processing after checksum transmission completes. * If the bus collision detection function is not used Perform hardware LIN end processing after header field transmission and reception complete. Timer RA Timer RA Set the timer to stop counting TSTART bit in TRACR register 0 Read the count status flag TCSTF flag in TRACR register TCSTF = 0 ? NO YES UART0 Complete transmission via UART0 Hardware LIN Hardware LIN Figure 18.12 Clear the status flags (Bus collision detection, Synch Break detection, Synch Field measurement) Bits B2CLR, B1CLR, B0CLR in the LINST register 1 Set the timer to stop counting. Zero to one cycle of the timer RA count source is required after timer RA starts counting before the TCSTF flag is set to 1. When the bus collision detection function is not used, end processing for the UART0 transmission is not required. After clearing hardware LIN status flag, stop the hardware LIN operation. Set the LIN operation to stop LINE bit in the LINCR register 0 Example of Hardware LIN Communication Completion Flowchart Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 345 of 450 R8C/2K Group, R8C/2L Group 18.5 18. Hardware LIN Interrupt Requests There are four interrupt requests that are generated by the hardware LIN: Synch Break detection, Synch Break generation completed, Synch Field measurement completed, and bus collision detection. These interrupts are shared with timer RA. Table 18.2 lists the Interrupt Requests of Hardware LIN. Table 18.2 Interrupt Requests of Hardware LIN Interrupt Request Synch Break detection Status Flag Cause of Interrupt SBDCT Generated when timer RA has underflowed after measuring the "L" level duration of RXD0 input, or when a "L" level is input for a duration longer than the Synch Break period during communication. Synch Break generation completed Generated when "L" level output to TXD0 for the duration set by timer RA completes. Synch Field measurement completed SFDCT Generated when measurement for 6 bits of the Synch Field by timer RA is completed. Bus collision detection BCDCT Generated when the RXD0 input and TXD0 output values differed at data latch timing while UART0 is enabled for transmission. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 346 of 450 R8C/2K Group, R8C/2L Group 18.6 18. Hardware LIN Notes on Hardware LIN For the time-out processing of the header and response fields, use another timer to measure the duration of time with a Synch Break detection interrupt as the starting point. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 347 of 450 R8C/2K Group, R8C/2L Group 19. A/D Converter 19. A/D Converter The A/D converter consists of one 10-bit successive approximation A/D converter circuit with a capacitive coupling amplifier. The analog input shares pins P0_0 to P0_3, P0_5, and P1_0 to P1_3. Therefore, when using these pins, ensure that the corresponding port direction bits are set to 0 (input mode). When not using the A/D converter, set the VCUT bit in the ADCON1 register to 0 (Vref unconnected) so that no current will flow from the VREF pin into the resistor ladder. This helps to reduce the power consumption of the chip. The result of A/D conversion is stored in the AD register. Table 19.1 lists the Performance of A/D converter. Figure 19.1 shows a Block Diagram of A/D Converter. Figures 19.2 and 19.3 show the A/D converter-related registers. Table 19.1 Performance of A/D converter Item A/D conversion method Performance Successive approximation (with capacitive coupling amplifier) 0 V to AVCC Analog input voltage(1) 4.2 V AVCC 5.5 V f1, f2, f4, fOCO-F 2.7 V AVCC < 4.2 V f2, f4, fOCO-F 8 bits or 10 bits selectable AVCC = Vref = 5 V, AD = 10 MHz * 8-bit resolution 2 LSB * 10-bit resolution 3 LSB AVCC = Vref = 3.3 V, AD = 10 MHz * 8-bit resolution 2 LSB * 10-bit resolution 5 LSB Operating clock AD(2) Resolution Absolute accuracy Operating mode Analog input pin A/D conversion start condition Conversion rate per pin One-shot and repeat(3) 9 pins (AN2, AN4 to AN11) * Software trigger Set the ADST bit in the ADCON0 register to 1 (A/D conversion starts) * Capture Timer RD interrupt request is generated while the ADST bit is set to 1 * Without sample and hold function 8-bit resolution: 49AD cycles, 10-bit resolution: 59AD cycles * With sample and hold function 8-bit resolution: 28AD cycles, 10-bit resolution: 33AD cycles NOTES: 1. The analog input voltage does not depend on use of a sample and hold function. When the analog input voltage is over the reference voltage, the A/D conversion result will be 3FFh in 10-bit mode and FFh in 8-bit mode. 2. When 2.7 V AVCC 5.5 V, the frequency of AD must be 10 MHz or below. Without a sample and hold function, the AD frequency should be 250 kHz or above. With a sample and hold function, the AD frequency should be 1 MHz or above. 3. In repeat mode, only 8-bit mode can be used. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 348 of 450 R8C/2K Group, R8C/2L Group 19. A/D Converter CKS0 = 1 fOCO-F A/D conversion rate selection CKS1 = 1 f1 CKS0 = 0 CKS0 = 1 AD f2 CKS1 = 0 f4 CKS0 = 0 VCUT = 0 AVSS VREF Resistor ladder VCUT = 1 Successive conversion register Software trigger ADCAP = 0 ADCON0 Trigger Timer RD interrupt request ADCAP = 1 Vcom AD register Decoder Comparator VIN Data bus P0_5/AN2 P0_3/AN4 P0_2/AN5 P0_1/AN6 P0_0/AN7 P1_0/AN8 P1_1/AN9 P1_2/AN10 P1_3/AN11 CH2 to CH0 = 010b CH2 to CH0 = 100b CH2 to CH0 = 101b CH2 to CH0 = 110b CH2 to CH0 = 111b ADGSEL0 = 0 ADGSEL0 = 1 CH2 to CH0 = 100b CH2 to CH0 = 101b CH2 to CH0 = 110b CH2 to CH0 = 111b CH0 to CH2, ADGSEL0, ADCAP, CKS0: Bits in ADCON0 register CKS1, VCUT: Bits in ADCON1 register Figure 19.1 Block Diagram of A/D Converter Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 349 of 450 R8C/2K Group, R8C/2L Group 19. A/D Converter A/D Control Register 0(1) b7 b6 b5 b4 b3 b2 b1 b0 Symbol ADCON0 Bit Symbol CH0 Address 00D6h Bit Name Analog input pin select bits (Note 4) After Reset 00h Function RW CH2 RW ADGSEL0 ADCAP ADST A/D operating mode select 0 : One-shot mode 1 : Repeat mode bit(2) RW A/D input group select bit(4) 0 : Selects port P0 group (AN2, AN4 to AN7) 1 : Selects port P1 group (AN8 to AN11) RW A/D conversion automatic start bit 0 : Starts at softw are trigger (ADST bit) 1 : Starts at timer RD (complementary PWM mode) RW A/D conversion start flag 0 : Stops A/D conversion 1 : Starts A/D conversion RW Frequency select bit 0 [When CKS1 in ADCON1 register = 0] 0 : Select f4 1 : Select f2 [When CKS1 in ADCON1 register = 1] 0 : Select f1(3) 1 : Select fOCO-F RW CKS0 NOTES: 1. If the ADCON0 register is rew ritten during A/D conversion, the conversion result is undefined. 2. When changing A/D operation mode, set the analog input pin again. 3. Set oAD frequency to 10 MHz or below . 4. The analog input pin can be selected according to a combination of bits CH0 to CH2 and the ADGSEL0 bit. Figure 19.2 ADGSEL0=0 -- Do not set. AN2 Do not set. AN4 AN5 AN6 AN7 ADGSEL0=1 Do not set. AN8 AN9 AN10 AN11 ADCON0 Register Rev.1.10 Dec 21, 2007 REJ09B0406-0110 RW CH1 MD CH2 to CH0 000b 001b 010b 011b 100b 101b 110b 111b RW Page 350 of 450 R8C/2K Group, R8C/2L Group 19. A/D Converter A/D Control Register 1(1) b7 b6 b5 b4 b3 b2 b1 b0 0 0 0 0 0 Symbol Address 00D7h ADCON1 Bit Symbol Bit Name Reserved bits -- (b2-b0) BITS CKS1 VCUT -- (b6-b7) After Reset 00h Function RW Set to 0. RW 8/10-bit mode select bit(2) 0 : 8-bit mode 1 : 10-bit mode RW Frequency select bit 1 Refer to the description of the CKS0 bit in the ADCON0 register function. RW VREF connect bit(3) 0 : VREF not connected 1 : VREF connected RW Reserved bits Set to 0. RW NOTES: 1. If the ADCON1 register is rew ritten during A/D conversion, the conversion result is undefined. 2. Set the BITS bit to 0 (8-bit mode) in repeat mode. 3. When the VCUT bit is set to 1 (connected) from 0 (not connected), w ait for 1 s or more before starting A/D conversion. A/D Control Register 2(1) b7 b6 b5 b4 b3 b2 b1 b0 0 0 0 Symbol ADCON2 Bit Symbol Address 00D4h Bit Name A/D conversion method select bit After Reset 00h Function 0 : Without sample and hold 1 : With sample and hold -- (b3-b1) Reserved bits Set to 0. -- (b7-b4) Nothing is assigned. If necessary, set to 0. When read, the content is 0. SMP RW RW RW -- NOTE: 1. If the ADCON2 register is rew ritten during A/D conversion, the conversion result is undefined. A/D Register (b15) b7 (b8) b0 b7 b0 Symbol AD Address 00C1h-00C0h After Reset Undefined Function When BITS bit in ADCON1 register is set to 1 (10-bit mode). 8 low -order bits in A/D conversion result 2 high-order bits in A/D conversion result Nothing is assigned. If necessary, set to 0. When read, the content is 0. Figure 19.3 Registers ADCON1, ADCON2, and AD Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 351 of 450 When BITS bit in ADCON1 register is set to 0 (8-bit mode). A/D conversion result When read, the content is undefined. RW RO RO -- R8C/2K Group, R8C/2L Group 19.1 19. A/D Converter One-Shot Mode In one-shot mode, the input voltage of one selected pin is A/D converted once. Table 19.2 lists the Specification of One-Shot Mode. Figures 19.4 and 19.5 show Registers ADCON0 and ADCON1 in One-Shot Mode. Table 19.2 Specification of One-Shot Mode Item Specification Function The input voltage of one pin selected by bits CH2 to CH0 and ADGSEL0 is A/D converted once Start condition * When the ADCAP bit is set to 0 (software trigger): Set the ADST bit to 1 (A/D conversion starts) * When the ADCAP bit is set to 1 (starts in timer RD (complementary PWM mode): A compare match between registers TRD0 and TRDGRA0 or a TRD1 underflow is generated while the ADST bit is set to 1 Stop condition * A/D conversion completes (when the ADCAP bit is set to 0 (software trigger), ADST bit is set to 0) * Set the ADST bit to 0 Interrupt request generation A/D conversion completes timing Input pin Select one of AN2, AN4 to AN11 Reading of A/D conversion Read AD register result Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 352 of 450 R8C/2K Group, R8C/2L Group 19. A/D Converter A/D Control Register 0(1) b7 b6 b5 b4 b3 b2 b1 b0 0 Symbol ADCON0 Bit Symbol CH0 Address 00D6h Bit Name Analog input pin select bits (Note 4) After Reset 00h Function RW CH2 RW ADGSEL0 ADCAP ADST A/D operating mode select 0 : One-shot mode bit(2) RW A/D input group select bit(4) 0 : Selects port P0 group (AN2, AN4 to AN7) 1 : Selects port P1 group (AN8 to AN11) RW A/D conversion automatic start bit 0 : Starts at softw are trigger (ADST bit) 1 : Starts at timer RD (complementary PWM mode) RW A/D conversion start flag 0 : Stops A/D conversion 1 : Starts A/D conversion RW Frequency select bit 0 [When CKS1 in ADCON1 register = 0] 0 : Select f4 1 : Select f2 [When CKS1 in ADCON1 register = 1] 0 : Select f1(3) 1 : Select fOCO-F RW CKS0 NOTES: 1. If the ADCON0 register is rew ritten during A/D conversion, the conversion result is undefined. 2. After changing the A/D operating mode, select the analog input pin again. 3. Set oAD frequency to 10 MHz or below . 4. The analog input pin can be selected according to a combination of bits CH0 to CH2 and the ADGSEL0 bit. Figure 19.4 ADGSEL0=0 -- Do not set. AN2 Do not set. AN4 AN5 AN6 AN7 ADGSEL0=1 Do not set. AN8 AN9 AN10 AN11 ADCON0 Register in One-Shot Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 RW CH1 MD CH2 to CH0 000b 001b 010b 011b 100b 101b 110b 111b RW Page 353 of 450 R8C/2K Group, R8C/2L Group 19. A/D Converter A/D Control Register 1(1) b7 b6 b5 b4 b3 b2 b1 b0 0 0 1 0 0 0 Symbol Address 00D7h ADCON1 Bit Symbol Bit Name Reserved bits -- (b2-b0) BITS CKS1 VCUT -- (b6-b7) After Reset 00h Function Set to 0. 0 : 8-bit mode 1 : 10-bit mode RW Frequency select bit 1 Refer to the description of the CKS0 bit in the ADCON0 register function. RW VREF connect bit(2) 1 : VREF connected Reserved bits Set to 0. ADCON1 Register in One-Shot Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 RW 8/10-bit mode select bit NOTES: 1. If the ADCON1 register is rew ritten during A/D conversion, the conversion result is undefined. 2. When the VCUT bit is set to 1 (connected) from 0 (not connected), w ait for 1 s or more before starting A/D conversion. Figure 19.5 RW Page 354 of 450 RW RW R8C/2K Group, R8C/2L Group 19.2 19. A/D Converter Repeat Mode In repeat mode, the input voltage of one selected pin is A/D converted repeatedly. Table 19.3 lists the Repeat Mode Specifications. Figures 19.6 and 19.7 show Registers ADCON0 and ADCON1 in Repeat Mode. Table 19.3 Repeat Mode Specifications Item Specification Function The Input voltage of one pin selected by bits CH2 to CH0 and ADGSEL0 is A/D converted repeatedly Start conditions * When the ADCAP bit is set to 0 (software trigger): Set the ADST bit to 1 (A/D conversion starts) * When the ADCAP bit is set to 1 (starts in timer RD (complementary PWM mode): A compare match between registers TRD0 and TRDGRA0 or a TRD1 underflow is generated while the ADST bit is set to 1 Stop condition Set the ADST bit to 0 Interrupt request generation Not generated timing Input pin Select one of AN2, AN4 to AN11 Reading of result of A/D Read AD register converter Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 355 of 450 R8C/2K Group, R8C/2L Group 19. A/D Converter A/D Control Register 0(1) b7 b6 b5 b4 b3 b2 b1 b0 1 Symbol ADCON0 Bit Symbol CH0 Address 00D6h Bit Name Analog input pin select bits (Note 4) After Reset 00h Function RW CH2 RW A/D operating mode select 1 : Repeat mode bit(2) (4) ADGSEL0 ADCAP ADST 0 : Selects port P0 group (AN2, AN4 to AN7) 1 : Selects port P1 group (AN8 to AN11) RW A/D conversion automatic start bit 0 : Starts at softw are trigger (ADST bit) 1 : Starts at timer RD (complementary PWM mode) RW A/D conversion start flag 0 : Stops A/D conversion 1 : Starts A/D conversion RW Frequency select bit 0 [When CKS1 in ADCON1 register = 0] 0 : Select f4 1 : Select f2 [When CKS1 in ADCON1 register = 1] 0 : Select f1(3) 1 : Do not set. RW NOTES: 1. If the ADCON0 register is rew ritten during A/D conversion, the conversion result is undefined. 2. After changing A/D operation mode, select the analog input pin again. 3. Set oAD frequency to 10 MHz or below . 4. The analog input pin can be selected according to a combination of bits CH0 to CH2 and the ADGSEL0 bit. ADGSEL0=0 -- Do not set. AN2 Do not set. AN4 AN5 AN6 AN7 ADGSEL0=1 Do not set. AN8 AN9 AN10 AN11 ADCON0 Register in Repeat Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 RW A/D input group select bit CKS0 Figure 19.6 RW CH1 MD CH2 to CH0 000b 001b 010b 011b 100b 101b 110b 111b RW Page 356 of 450 R8C/2K Group, R8C/2L Group 19. A/D Converter A/D Control Register 1(1) b7 b6 b5 b4 b3 b2 b1 b0 0 0 1 0 0 0 0 Symbol Address 00D7h ADCON1 Bit Symbol Bit Name Reserved bits -- (b2-b0) BITS CKS1 VCUT -- (b6-b7) After Reset 00h Function Set to 0. 8/10-bit mode select bit(2) 0 : 8-bit mode Frequency select bit 1 Refer to the description of the CKS0 bit in the ADCON0 register function. VREF connect bit(3) 1 : VREF connected Reserved bits Set to 0. NOTES: 1. If the ADCON1 register is rew ritten during A/D conversion, the conversion result is undefined. 2. Set the BITS bit to 0 (8-bit mode) in repeat mode. 3. When the VCUT bit is set to 1 (connected) from 0 (not connected), w ait for 1 s or more before starting A/D conversion. Figure 19.7 ADCON1 Register in Repeat Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 357 of 450 RW RW RW RW RW RW R8C/2K Group, R8C/2L Group 19.3 19. A/D Converter Sample and Hold When the SMP bit in the ADCON2 register is set to 1 (sample and hold function enabled), the A/D conversion rate per pin increases. The sample and hold function is available in all operating modes. Start A/D conversion after selecting whether the sample and hold circuit is to be used or not. Figure 19.8 shows a Timing Diagram of A/D Conversion. Sample and hold disabled Conversion time of 1st bit 2nd bit Comparison Sampling time Comparison Sampling time Comparison 2.5o AD cycles 2.5o AD cycles time time time Sampling time 4o AD cycles * Repeat until conversion ends Sample and hold enabled 2nd bit Conversion time of 1st bit Comparison time Sampling time 4o AD cycles Comparison Comparison Comparison time time time * Repeat until conversion ends Figure 19.8 19.4 Timing Diagram of A/D Conversion A/D Conversion Cycles Figure 19.9 shows the A/D Conversion Cycles. Conversion time at the 1st bit A/D Conversion Mode Conversion time at the 2nd bit and the follows Conversion Time Sampling Time Comparison Time Sampling Time 49AD 4AD 2.0AD 2.5AD End process Comparison End process Time Without Sample & Hold 8 bits Without Sample & Hold 10 bits 59AD 4AD 2.0AD 2.5AD 2.5AD 8.0AD With Sample & Hold 8 bits 28AD 4AD 2.5AD 0.0AD 2.5AD 4.0AD With Sample & Hold 10 bits 33AD 4AD 2.5AD 0.0AD 2.5AD 4.0AD Figure 19.9 A/D Conversion Cycles Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 358 of 450 2.5AD 8.0AD R8C/2K Group, R8C/2L Group 19.5 19. A/D Converter Internal Equivalent Circuit of Analog Input Figure 19.10 shows the Internal Equivalent Circuit of Analog Input. VCC VCC VSS AVCC ON Resistor Approx. 2k Wiring Resistor Approx. 0.2k Parasitic Diode AN0 SW1 ON Resistor Approx. 0.6k Analog Input Voltage SW2 Parasitic Diode i Ladder-type Switches i=9 AMP VIN ON Resistor Approx. 5k Sampling Control Signal VSS C = Approx.1.5pF SW3 SW4 i Ladder-type Wiring Resistors AVSS ON Resistor Approx. 2k Wiring Resistor Approx. 0.2k Chopper-type Amplifier AN11 SW1 b4 b2 b1 b0 A/D Control Register 0 Reference Control Signal A/D Successive Conversion Register Vref VREF Resistor ladder SW5 Comparison voltage ON Resistor Approx. 0.6k f A/D Conversion Interrupt Request AVSS Comparison reference voltage (Vref) generator Sampling Comparison SW1 conducts only on the ports selected for analog input. Connect to Control signal for SW2 Connect to Connect to Control signal for SW3 SW2 and SW3 are open when A/D conversion is not in progress; their status varies as shown by the waveforms in the diagrams on the left. SW4 conducts only when A/D conversion is not in progress. Connect to SW5 conducts when compare operation is in progress. NOTE: 1. Use only as a standard for designing this data. Mass production may cause some changes in device characteristics. Figure 19.10 Internal Equivalent Circuit of Analog Input Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 359 of 450 R8C/2K Group, R8C/2L Group 19.6 19. A/D Converter Output Impedance of Sensor under A/D Conversion To carry out A/D conversion properly, charging the internal capacitor C shown in Figure 19.11 has to be completed within a specified period of time. T (sampling time) as the specified time. Let output impedance of sensor equivalent circuit be R0, internal resistance of microcomputer be R, precision (error) of the A/D converter be X, and the resolution of A/D converter be Y (Y is 1024 in the 10-bit mode, and 256 in the 8-bit mode). VC is generally And when t = T, 1 - -------------------------C ( R0 + R ) VC = VIN 1 - e t X X VC = VIN - ---- VIN = VIN 1 - ---- Y Y 1 - --------------------------T C ( R0 + R) = X e ---Y 1 - -------------------------T = ln X ---C ( R0 + R ) Y Hence, T R0 = - ------------------- - R X C * ln ---Y Figure 19.11 shows the Analog Input Pin and External Sensor Equivalent Circuit. When the difference between VIN and VC becomes 0.1LSB, we find impedance R0 when voltage between pins VC changes from 0 to VIN-(0.1/ 1024) VIN in time T. (0.1/1024) means that A/D precision drop due to insufficient capacitor charge is held to 0.1LSB at time of A/D conversion in the 10-bit mode. Actual error however is the value of absolute precision added to 0.1LSB. When f(XIN) = 10 MHz, T = 0.25 s in the A/D conversion mode without sample and hold. Output impedance R0 for sufficiently charging capacitor C within time T is determined as follows. T = 0.25 s, R = 2.8 k, C = 6.0 pF, X = 0.1, and Y = 1024. Hence, 3 3 0.25 x 10 - 6 - - 2.8 x10 1.7 x10 R0 = - -------------------------------------------------0.1 6.0 x 10 - 12 * ln ----------1024 Thus, the allowable output impedance of the sensor equivalent circuit, making the precision (error) 0.1LSB or less, is approximately 1.7 k. maximum. MCU Sensor equivalent circuit R0 R (2.8 k) VIN C (6.0 pF) VC NOTE: 1. The capacity of the terminal is assumed to be 4.5 pF. Figure 19.11 Analog Input Pin and External Sensor Equivalent Circuit Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 360 of 450 R8C/2K Group, R8C/2L Group 19.7 19. A/D Converter Notes on A/D Converter * Write to each bit (other than bit 6) in the ADCON0 register, each bit in the ADCON1 register, or the SMP bit * * * * * * * in the ADCON2 register when A/D conversion is stopped (before a trigger occurs). When the VCUT bit in the ADCON1 register is changed from 0 (VREF not connected) to 1 (VREF connected), wait for at least 1 s before starting the A/D conversion. After changing the A/D operating mode, select an analog input pin again. When using the one-shot mode, ensure that A/D conversion is completed before reading the AD register. The IR bit in the ADIC register or the ADST bit in the ADCON0 register can be used to determine whether A/D conversion is completed. When using the repeat mode, select the frequency of the A/D converter operating clock AD or more for the CPU clock during A/D conversion. If the ADST bit in the ADCON0 register is set to 0 (A/D conversion stops) by a program and A/D conversion is forcibly terminated during an A/D conversion operation, the conversion result of the A/D converter will be undefined. If the ADST bit is set to 0 by a program, do not use the value of the AD register. Connect 0.1 F capacitor between the P4_2/VREF pin and AVSS pin. Do not enter stop mode during A/D conversion. Do not enter wait mode when the CM02 bit in the CM0 register is set to 1 (peripheral function clock stops in wait mode) during A/D conversion. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 361 of 450 R8C/2K Group, R8C/2L Group 20. Flash Memory 20. Flash Memory 20.1 Overview Rewrite operations to the flash memory can be performed in three modes: CPU rewrite, standard serial I/O, and parallel I/O. Table 20.1 lists the Flash Memory Version Performance (refer to Tables 1.1 and 1.4 Specifications for items not listed in Table 20.1). Table 20.1 Flash Memory Version Performance Item Flash memory operating modes Division of erase block Programming method Erase method Programming and erasure control method Suspend functions Protection method Number of commands Programming and Blocks 0 and 1 erasure endurance(1) (program ROM) Blocks A and B (data flash)(2) Programming and erasure voltage ID code check function ROM code protect Specification 3 modes (CPU rewrite, standard serial I/O, and parallel I/O) Refer to Figures 20.1 and 20.2. Byte unit Block erase Programming and erasure control by software command Program-suspend and erase-suspend Program ROM protection by FMR0 register 5 commands R8C/2K Group: 100 times; R8C/2L Group: 1,000 times 10,000 times VCC = 2.7 to 5.5 V Standard serial I/O mode supported Parallel I/O mode supported NOTES: 1. Definition of programming and erasure endurance. The programming and erasure endurance is defined on a per-block basis. 2. Blocks A and B (data flash) are included in the R8C/2L Group. Table 20.2 Flash Memory Rewrite Modes Flash Memory Rewrite Mode Function CPU Rewrite Mode User ROM area is rewritten by executing software commands from the CPU. Rewritable areas User ROM area Rewrite programs User program Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 362 of 450 Standard Serial I/O Mode Parallel I/O Mode User ROM area is rewritten by a dedicated serial programmer. User ROM area Standard boot program User ROM area is rewritten by a dedicated parallel programmer. User ROM area - R8C/2K Group, R8C/2L Group 20.2 20. Flash Memory Memory Map The flash memory contains a user ROM area and a boot ROM area (reserved area). Figure 20.1 shows the Flash Memory Block Diagram for R8C/2K Group and Figure 20.2 shows the Flash Memory Block Diagram for R8C/2L Group. The user ROM area contains program ROM. In addition, the R8C/2L Group has on-chip data flash. The user ROM area is divided into several blocks. The user ROM area can be rewritten in CPU rewrite mode, and standard serial I/O mode, and parallel I/O mode. The rewrite control program (standard boot program) for standard serial I/O mode is stored in the boot ROM area before shipment. The boot ROM area and the user ROM area share the same address, but have separate memory areas. 16 Kbytes ROM product 0C000h Block 1: 8 Kbytes(1) 0DFFFh 0E000h Block 0: 8 Kbytes(1) 8 Kbytes ROM product Program ROM 0E000h Block 0: 8 Kbytes(1) 0E000h 8 Kbytes 0FFFFh 0FFFFh 0FFFFh User ROM area User ROM area Boot ROM area (reserved area)(2) NOTES: 1. When the FMR02 bit in the FMR0 register is set to 1 (rewrite enabled) and the FMR15 bit in the FMR1 register is set to 0 (rewrite enabled), block 0 is rewritable. When the FMR16 bit is set to 0 (rewrite enabled), block 1 is rewritable (only for CPU rewrite mode). 2. This area is for storing the boot program provided by Renesas Technology. Figure 20.1 Flash Memory Block Diagram for R8C/2K Group 16 Kbytes ROM product 02400h Block A: 1 Kbyte 8 Kbytes ROM product 02400h Block A: 1 Kbyte Data flash 02BFFh 0C000h 0DFFFh 0E000h 0FFFFh Block B: 1 Kbyte 02BFFh Block B: 1 Kbyte Block 1: 8 Kbytes(1) Block 0: 8 Kbytes(1) 0E000h Program ROM Block 0: 8 Kbytes(1) User ROM area User ROM area 0E000h 8 Kbytes 0FFFFh 0FFFFh Boot ROM area (reserved area)(2) NOTES: 1. When the FMR02 bit in the FMR0 register is set to 1 (rewrite enabled) and the FMR15 bit in the FMR1 register is set to 0 (rewrite enabled), block 0 is rewritable. When the FMR16 bit is set to 0 (rewrite enabled), block 1 is rewritable (only for CPU rewrite mode). 2. This area is for storing the boot program provided by Renesas Technology. Figure 20.2 Flash Memory Block Diagram for R8C/2L Group Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 363 of 450 R8C/2K Group, R8C/2L Group 20.3 20. Flash Memory Functions to Prevent Rewriting of Flash Memory Standard serial I/O mode has an ID code check function, and parallel I/O mode has a ROM code protect function to prevent the flash memory from being read, rewritten, or erased. 20.3.1 ID Code Check Function The ID code check function is used in standard serial I/O mode. Unless 3 bytes (addresses from 0FFFCh to 0FFFEh) of the reset vector are set to FFFFFFh, the ID codes sent from the serial programmer or the on-chip debugging emulator and the 7-byte ID codes written in the flash memory are checked to see if they match. If the ID codes do not match, the commands sent from the serial programmer or the on-chip debugging emulator are not acknowledged. For details of the ID code check function, refer to 13. ID Code Areas. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 364 of 450 R8C/2K Group, R8C/2L Group 20.3.2 20. Flash Memory ROM Code Protect Function The ROM protect function prevents the contents of the flash memory from being read, rewritten, or erased by means of the OFS register when parallel I/O mode is used. Figure 20.3 shows the OFS Register. Refer to 14. Option Function Select Area for details of the OFS register. The ROM code protect function is enabled by writing 0 to the ROMCP1 bit and 1 to the ROMCR bit. It disables reading or changing the contents of the on-chip flash memory. Once ROM code protect is enabled, the content in the internal flash memory cannot be rewritten in parallel I/O mode. To disable ROM code protect, erase the block including the OFS register with CPU rewrite mode or standard serial I/O mode. Option Function Select Register(1) b7 b6 b5 b4 b3 b2 b1 b0 1 1 1 Symbol OFS Bit Symbol WDTON -- (b1) ROMCR ROMCP1 -- (b4) LVD0ON -- (b6) Address 0FFFFh Bit Name Watchdog timer start select bit When Shipping FFh(3) Function 0 : Starts w atchdog timer automatically after reset 1 : Watchdog timer is inactive after reset Reserved bit Set to 1. ROM code protect disabled bit 0 : ROM code protect disabled 1 : ROMCP1 enabled RW ROM code protect bit 0 : ROM code protect enabled 1 : ROM code protect disabled RW Reserved bit Set to 1. Voltage detection 0 circuit start bit(2) 0 : Voltage monitor 0 reset enabled after hardw are reset 1 : Voltage monitor 0 reset disabled after hardw are reset Reserved bit Set to 1. Count source protect CSPROINI mode after reset select bit 0 : Count source protect mode enabled after reset 1 : Count source protect mode disabled after reset RW RW RW RW RW RW RW NOTES: 1. The OFS register is on the flash memory. Write to the OFS register w ith a program. After w riting is completed, do not w rite additions to the OFS register. 2. Setting the LVD0ON bit is only valid after a hardw are reset. To use the pow er-on reset, set the LVD0ON bit to 0 (voltage monitor 0 reset enabled after hardw are reset). 3. If the block including the OFS register is erased, FFh is set to the OFS register. Figure 20.3 OFS Register Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 365 of 450 R8C/2K Group, R8C/2L Group 20.4 20. Flash Memory CPU Rewrite Mode In CPU rewrite mode, the user ROM area can be rewritten by executing software commands from the CPU. Therefore, the user ROM area can be rewritten directly while the MCU is mounted on a board without using a ROM programmer. Execute the software command only to blocks in the user ROM area. The flash module has an erase-suspend function when an interrupt request is generated during an erase operation in CPU rewrite mode. It performs an interrupt process after the erase operation is halted temporarily. During erasesuspend, the user ROM area can be read by a program. In case an interrupt request is generated during an auto-program operation in CPU rewrite mode, the flash module has a program-suspend function which performs the interrupt process after the auto-program operation is suspended. During program-suspend, the user ROM area can be read by a program. CPU rewrite mode has an erase write 0 mode (EW0 mode) and an erase write 1 mode (EW1 mode). Table 20.3 lists the Differences between EW0 Mode and EW1 Mode. Table 20.3 Differences between EW0 Mode and EW1 Mode Item Operating mode Areas in which a rewrite control program can be executed Rewritable areas EW0 Mode Single-chip mode RAM (Rewrite control program is executed after being transferred) EW1 Mode Single-chip mode User ROM or RAM User ROM Software command restrictions None Modes after program or erase Modes after read status register CPU status during autowrite and auto-erase Flash memory status detection Read status register mode User ROM However, blocks which contain a rewrite control program are excluded * Program and block erase commands Cannot be run on any block which contains a rewrite control program * Read status register command Cannot be executed Read array mode Read status register mode Do not execute this command Operating Conditions for transition to erase-suspend Conditions for transitions to program-suspend CPU clock Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Hold state (I/O ports hold state before the command is executed) * Read bits FMR00, FMR06, and FMR07 Read bits FMR00, FMR06, and FMR07 in in the FMR0 register by a program the FMR0 register by a program * Execute the read status register command and read bits SR7, SR5, and SR4 in the status register. Set bits FMR40 and FMR41 in the FMR4 The FMR40 bit in the FMR4 register is set register to 1 by a program. to 1 and the interrupt request of the enabled maskable interrupt is generated Set bits FMR40 and FMR42 in the FMR4 The FMR40 bit in the FMR4 register is set register to 1 by a program. to 1 and the interrupt request of the enabled maskable interrupt is generated 5 MHz or below No restriction (on clock frequency to be used) Page 366 of 450 R8C/2K Group, R8C/2L Group 20.4.1 20. Flash Memory Register Description The registers used in CPU rewrite mode are described. 20.4.1.1 FMR0 Register (FMR0) Figure 20.4 shows the FMR0 Register. Flash Memory Control Register 0 b7 b6 b5 b4 b3 b2 b1 b0 0 0 Symbol FMR0 Bit Symbol FMR00 FMR01 FMR02 Address 01B7h ____ Bit Name RY/BY status flag FMR06 FMR07 Function 0 : Busy (w riting or erasing in progress) 1 : Ready RW RO CPU rew rite mode select bit(1) 0 : CPU rew rite mode disabled 1 : CPU rew rite mode enabled RW Blocks 0 and 1 rew rite enable bit(2, 6) 0 : Rew rite disabled 1 : Rew rite enabled RW Flash memory stop bit(3, 5) 0 : Flash memory operates 1 : Flash memory stops (low -pow er consumption state and flash memory initialization) RW FMSTP -- (b5-b4) After Reset 00000001b Reserved bits Set to 0. Program status flag(4) 0 : Completed successfully 1 : Terminated in error RO Erase status flag(4) 0 : Completed successfully 1 : Terminated in error RO RW NOTES: 1. To set this bit to 1, set it to 1 immediately after setting it first to 0. Do not generate an interrupt betw een setting the bit to 0 and setting it to 1. Enter read array mode and set this bit to 0. 2. Set this bit to 1 immediately after setting it first to 0 w hile the FMR01 bit is set to 1. Do not generate an interrupt betw een setting the bit to 0 and setting it to 1. 3. Set this bit by a program located in a space other than the flash memory. 4. This bit is set to 0 by executing the clear status command. 5. This bit is enabled w hen the FMR01 bit is set to 1 (CPU rew rite mode). When the FMR01 bit is set to 0, w riting 1 to the FMSTP bit causes the FMSTP bit to be set to 1. The flash memory does not enter low -pow er consumption state nor is it initialized. 6. When setting the FMR01 bit to 0 (CPU rew rite mode disabled), the FMR02 bit is set to 0 (rew rite disabled). Figure 20.4 FMR0 Register Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 367 of 450 R8C/2K Group, R8C/2L Group 20. Flash Memory * FMR00 Bit This bit indicates the operating status of the flash memory. The bits value is 0 during programming, erasure (including suspend periods), or erase-suspend mode; otherwise, it is 1. * FMR01 Bit The MCU is made ready to accept commands by setting the FMR01 bit to 1 (CPU rewrite mode). * FMR02 Bit Rewriting of blocks 0 and 1 does not accept program or block erase commands if the FMR02 bit is set to 0 (rewrite disabled). Rewriting of blocks 0 and 1 is controlled by bits FMR15 and FMR16 if the FMR02 bit is set to 1 (rewrite enabled). * FMSTP Bit This bit is used to initialize the flash memory control circuits, and also to reduce the amount of current consumed by the flash memory. Access to the flash memory is disabled by setting the FMSTP bit to 1. Therefore, the FMSTP bit must be written to by a program transferred to the RAM. In the following cases, set the FMSTP bit to 1: - When flash memory access resulted in an error while erasing or programming in EW0 mode (FMR00 bit not initialized to 1 (ready)) - To provide lower consumption in low-speed on-chip oscillator mode and low-speed clock mode. Note that when going to stop or wait mode while the CPU rewrite mode is disabled, the FMR0 register does not need to be set because the power for the flash memory is automatically turned off and is turned back on again after returning from stop or wait mode. * FMR06 Bit This is a read-only bit indicating the status of an auto-program operation. The bit is set to 1 when a program error occurs; otherwise, it is set to 0. For details, refer to the description in Table 20.4 Errors and FMR0 Register Status. * FMR07 Bit This is a read-only bit indicating the status of an auto-erase operation. The bit is set to 1 when an erase error occurs; otherwise, it is set to 0. Refer to Table 20.4 Errors and FMR0 Register Status for details. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 368 of 450 R8C/2K Group, R8C/2L Group Table 20.4 20. Flash Memory Errors and FMR0 Register Status FRM0 Register (Status Register) Status Error FMR07 (SR5) FMR06 (SR4) 1 1 Command sequence error 1 0 0 1 0 0 Error Occurrence Condition * When a command is not written correctly. * When D0h or FFh is not written in the 2nd byte of the block erase command.(1) * When the program command or block erase command is executed while rewriting is disabled by the FMR02 bit in the FMR0 register, or the FMR15 bit in the FMR1 register. * When an address not allocated in flash memory is input during erase command input * When attempting to erase the block for which rewriting is disabled during erase command input. * When an address not allocated in flash memory is input during write command input. * When attempting to write to a block for which rewriting is disabled during write command input. Erase error * When the block erase command is executed but auto-erasure does not complete correctly Program error * When the program command is executed but not auto-programming does not complete. Completed successfully - NOTE: 1. When FFh is written in the 2nd byte of the block erase command, the MCU enters read array mode, and the command code written in the 1st byte is disabled. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 369 of 450 R8C/2K Group, R8C/2L Group 20.4.1.2 20. Flash Memory FMR1 Register (FMR1) Figure 20.5 shows the FMR1 Register. Flash Memory Control Register 1 b7 b6 b5 b4 b3 b2 b1 b0 1 0 0 0 Symbol Address 01B5h FMR1 Bit Symbol Bit Name Reserved bit -- (b0) FMR11 -- (b4-b2) FMR15 FMR16 -- (b7) After Reset 1000000Xb Function When read, the content is undefined. RW RO EW1 mode select bit(1, 2) 0 : EW0 mode 1 : EW1 mode Reserved bits Set to 0. Block 0 rew rite disable bit(2,3) 0 : Rew rite enabled 1 : Rew rite disabled RW Block 1 rew rite disable bit(2,3) 0 : Rew rite enabled 1 : Rew rite disabled RW Reserved bit Set to 1. RW RW RW NOTES: 1. To set this bit to 1, set it to 1 immediately after setting it first to 0 w hile the FMR01 bit is set to 1 (CPU rew rite mode enabled). Do not generate an interrupt betw een setting the bit to 0 and setting it to 1. 2. This bit is set to 0 by setting the FMR01 bit in the FMR0 register to 0 (CPU rew rite mode disabled). 3. While the FMR01 bit is set to 1 (CPU rew rite mode enabled), bits FMR15 and FMR 16 can be w ritten to. To set this bit to 0, set it to 0 immediately after setting it first to 1. To set this bit to 1, set it to 1. Figure 20.5 FMR1 Register * FMR11 Bit Setting this bit to 1 (EW1 mode) places the MCU in EW1 mode. * FMR15 Bit When the FMR02 bit is set to 1 (rewrite enabled) and the FMR15 bit is set to 0 (rewrite enabled), block 0 accepts program and block erase commands. * FMR16 Bit When the FMR02 bit is set to 1 (rewrite enabled) and the FMR16 bit is set to 0 (rewrite enabled), block 1 accepts program and block erase commands. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 370 of 450 R8C/2K Group, R8C/2L Group 20.4.1.3 20. Flash Memory FMR4 Register (FMR4) Figure 20.6 shows the FMR4 Register. Flash Memory Control Register 4 b7 b6 b5 b4 b3 b2 b1 b0 0 Symbol FMR4 Bit Symbol FMR40 FMR41 FMR42 FMR43 FMR44 -- (b5) FMR46 FMR47 Address 01B3h Bit Name Erase-suspend function enable bit(1) Erase-suspend request bit(2) After Reset 01000000b Function RW 0 : Disabled 1 : Enabled RW 0 : Erasure restarts 1 : Erase-suspend request RW Program-suspend request bit(3) 0 : Programming restarts 1 : Program-suspend request RW Erase command flag 0 : Erase not executed 1 : Erase execution in progress RO Program command flag 0 : Program not executed 1 : Program execution in progress RO Reserved bit Set to 0. Read status flag 0 : Reading disabled 1 : Reading enabled RO Low -current-consumption read mode enable bit (1, 4, 5) 0 : Disabled 1 : Enabled RW RO NOTES: 1. To set this bit to 1, set it to 1 immediately after setting it first to 0. Do not generate an interrupt betw een setting the bit to 0 and setting it to 1. 2. This bit is enabled w hen the FMR40 bit is set to 1 (enabled) and it can be w ritten to during the period betw een issuing an erase command and completing the erase. (This bit is set to 0 during periods other than the above.) In EW0 mode, it can be set to 0 or 1 by a program. In EW1 mode, it is automatically set to 1 if a maskable interrupt is generated during an erase operation w hile the FMR40 bit is set to 1. Do not set this bit to 1 by a program (0 can be w ritten). 3. The FMR42 bit is enabled only w hen the FMR40 bit is set to 1 (enabled) and programming to the FMR42 bit is enabled until auto-programming ends after a program command is generated. (This bit is set to 0 during periods other than the above.) In EW0 mode, 0 or 1 can be programmed to the FMR42 bit by a program. In EW1 mode, the FMR42 bit is automatically set to 1 by generating a maskable interrupt during auto-programming w hen the FMR40 bit is set to 1. 1 cannot be w ritten to the FMR42 bit by a program. 4. In high-speed clock mode and high-speed on-chip oscillator mode, set the FMR47 bit to 0 (disabled). 5. Set the FMR01 bit to 0 (CPU rew rite mode disabled) in low -current-consumption read mode. Figure 20.6 FMR4 Register Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 371 of 450 R8C/2K Group, R8C/2L Group 20. Flash Memory * FMR40 Bit The suspend function is enabled by setting the FMR40 bit to 1 (enabled). * FMR41 Bit In EW0 mode, the MCU enters erase-suspend mode when the FMR41 bit is set to 1 by a program. The FMR41 bit is automatically set to 1 (erase-suspend request) when an interrupt request of an enabled interrupt is generated in EW1 mode, and then the MCU enters erase-suspend mode. Set the FMR41 bit to 0 (erasure restarts) when the auto-erase operation restarts. * FMR42 Bit In EW0 mode, the MCU enters program-suspend mode when the FMR42 bit is set to 1 by a program. The FMR42 bit is automatically set to 1 (program-suspend request) when an interrupt request of an enabled interrupt is generated in EW1 mode, and then the MCU enters program-suspend mode. Set the FMR42 bit to 0 (programming restarts) when the auto-program operation restarts. * FMR43 Bit When the auto-erase operation starts, the FMR43 bit is set to 1 (erase execution in progress). The FMR43 bit remains set to 1 (erase execution in progress) during erase-suspend operation. When the auto-erase operation ends, the FMR43 bit is set to 0 (erase not executed). * FMR44 Bit When the auto-program operation starts, the FMR44 bit is set to 1 (program execution in progress). The FMR44 bit remains set to 1 (program execution in progress) during program-suspend operation. When the auto-program operation ends, the FMR44 bit is set to 0 (program not executed). * FMR46 Bit The FMR46 bit is set to 0 (reading disabled) during auto-program or auto-erase execution and set to 1 (reading enabled) in suspend mode. Do not access the flash memory while this bit is set to 0. * FMR47 Bit Current consumption when reading the flash memory can be reduced by setting the FMR47 bit to 1 (enabled) in low-speed clock mode and low-speed on-chip oscillator mode. Refer to 21.2.10 Low-Current-Consumption Read Mode for details of the handling procedure. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 372 of 450 R8C/2K Group, R8C/2L Group 20.4.2 20. Flash Memory Status Check Procedure When an error occurs, bits FMR06 to FMR07 in the FMR0 register are set to 1, indicating the occurrence of an error. Therefore, checking these status bits (full status check) can be used to determine the execution result. Figure 20.7 shows the Full Status Check and Handling Procedure for Individual Errors. Command sequence error Full status check Execute the clear status register command (set these status flags to 0) FMR06 = 1 and FMR07 = 1? Yes Command sequence error Check if the command is properly input No Re-execute the command FMR07 = 1? Yes Erase error Erase error No Execute the clear status register command (set these status flags to 0) Erase command re-execution times 3 times? FMR06 = 1? Yes Program error No Yes Re-execute the block erase command No Program error Execute the clear status register command (set these status flags to 0) Full status check completed Specify an address other than the write address where the error occurs as the program address(1) NOTE: 1. To rewrite to the address where the program error occurs, check if the full status check is complete normally and write to the address after the block erase command is executed. Figure 20.7 Re-execute the program command Full Status Check and Handling Procedure for Individual Errors Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 373 of 450 Block targeting for erasure cannot be used R8C/2K Group, R8C/2L Group 20.4.3 20. Flash Memory EW0 Mode The MCU enters CPU rewrite mode and software commands can be acknowledged by setting the FMR01 bit in the FMR0 register to 1 (CPU rewrite mode enabled). In this case, since the FMR11 bit in the FMR1 register is set to 0, EW0 mode is selected. Use software commands to control program and erase operations. The FMR0 register or the status register can be used to determine when program and erase operations complete. Figure 20.8 shows the How to Set and Exit EW0 Mode. EW0 Mode Operating Procedure Rewrite control program Write 0 to the FMR01 bit before writing 1 (CPU rewrite mode enabled)(2) Set registers(1) CM0 and CM1 Execute software commands Transfer a rewrite control program which uses CPU rewrite mode to the RAM. Jump to the rewrite control program which has been transferred to the RAM. (The subsequent process is executed by the rewrite control program in the RAM.) Execute the read array command(3) Write 0 to the FMR01 bit (CPU rewrite mode disabled) Jump to a specified address in the flash memory NOTES: 1. Select 5 MHz or below for the CPU clock by the CM06 bit in the CM0 register and bits CM16 to CM17 in the CM1 register. 2. To set the FMR01 bit to 1, write 0 to the FMR01 bit before writing 1. Do not generate an interrupt between writing 0 and 1. Write to the FMR01 bit in the RAM. 3. Disable the CPU rewrite mode after executing the read array command. Figure 20.8 How to Set and Exit EW0 Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 374 of 450 R8C/2K Group, R8C/2L Group 20.4.3.1 20. Flash Memory Software Commands There are five types of software commands: * Read array * Read status register * Clear status register * Program * Block erase Figure 20.9 shows the Software Command Status Transition Diagram in EW0 Mode. Read array mode Reset CPU rewrite disabled (FMR46 = 1 Reading enabled) No command required Reading only available Write 1 to the FMR01 bit immediately after writing 0. CPU rewrite mode (EW0 mode) FMR01 = 0 Program suspend 40h (Program command) 70h FMR42 = 0 (Read status register command) (Restart) FFh (Programming starts) FMR41 = 0 (Restart) (Read array command) Program Read status register mode 20h (Block erase command) Clear ends Clear status register Block erase Non-D0h and non-FFh D0h (Block erasure starts) FMR42 = 1 (Suspend request) FMR41 = 1 (Suspend request) Auto-erase Auto-program (FMR46 = 0 Reading disabled) Auto-programming completed Figure 20.9 (FMR46 = 0 Reading disabled) Auto-erasure completed Software Command Status Transition Diagram in EW0 Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 375 of 450 50h (Clear status register command) FFh (Read array command) Write data Erase suspend Read array mode (FMR46 = 1 Reading enabled) R8C/2K Group, R8C/2L Group 20. Flash Memory * Read Array Command The read array command reads the flash memory. When FFh is written to an address in the user ROM area, the MCU enters read array mode. In this mode, the contents of the specified address can be read. Read array mode continues until other commands are written. The MCU enters this mode after a reset is deasserted. * Read Status Register Command The read status register command is used to read the status register. Figure 20.10 shows the Status Register. The status register indicates the operating status of the flash memory and whether an erase or program operation has completed normally or in error (refer to Table 20.4 Errors and FMR0 Register Status). When 70h is written to an address in the user ROM area, the MCU enters read status register mode. When the address in the user ROM area is read subsequently, the status register can be read. The MCU remains in read status register mode until the next read array command is written. The status of the status register can be determined by reading bits FMR00, FMR06, and FMR07 in the FMR0 register. D7 D6 D5 D4 D3 D2 D1 D0 SR7 SR6 SR5 SR4 SR3 SR2 SR1 SR0 Status register FMR0 register FMR06 bit FMR07 bit FMR00 bit D0 to D7: These indicate the read data buses when the read status command is executed. Figure 20.10 Status Register * Clear Status Register Command The clear status register command sets the status register to 0. When 50h is written to an address in the user ROM area, bits FMR07 and FMR06 in the FMR0 register and bits SR5 and SR4 in the status register are set to 00b. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 376 of 450 R8C/2K Group, R8C/2L Group 20. Flash Memory * Program Command The program command writes data to the flash memory in 1-byte units. When 40h is written and then data is written to the write address, an auto-program operation (data program and verify) starts. The FMR00 bit in the FMR0 register can be used to determine whether auto-programming has completed. When suspend function disabled, the FMR00 bit is set to 0 during auto-programming and set to 1 when autoprogramming completes. When suspend function enabled, the FMR44 bit is set to 1 during auto-programming and set to 0 when auto-programming completes. The FMR06 bit in the FMR0 register can be used to determine the result of auto-programming after it has been finished (refer to 20.4.2 Status Check Procedure). Do not write additions to the already programmed addresses. Also, when the FMR02 bit in the FMR0 register is set to 0 (rewrite disabled), or the FMR02 bit is set to 1 (rewrite enabled) and the FMR15 bit in the FMR1 register is set to 1 (rewrite disabled), program commands targeting block 0 are not acknowledged. Figure 20.11 shows the Program Command in EW0 Mode (When Suspend Function Disabled). Figure 20.12 shows the Program Command in EW0 Mode (When Suspend Function Enabled). In EW0 mode, the MCU enters read status register mode at the same time auto-programming starts and the status register can be read. In this case, the MCU remains in read status register mode until the next read array command is written. Start Write the command code 40h to the write address Write data to the write address FMR00 = 1? No Yes Full status check Program completed Figure 20.11 Program Command in EW0 Mode (When Suspend Function Disabled) Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 377 of 450 R8C/2K Group, R8C/2L Group 20. Flash Memory Maskable interrupt(1) Start FMR40 = 1 FMR44 = 1 ? Write the command code 40h No Yes FMR42 = 1(3) I = 1 (enable interrupt)(2) FMR46 = 1 ? No Write data to the write address Access flash memory Yes FMR44 = 0 ? No Yes Access flash memory FMR42 = 0 Full status check REIT Program completed NOTES: 1. In EW0 mode, the interrupt vector table and interrupt routine for interrupts to be used should be allocated to the RAM area. 2. When no interrupt is used, the instruction to enable interrupts is not needed. 3. td(SR-SUS) is needed until program is suspended after the FMR42 bit in the FMR4 register is set to 1. Figure 20.12 Program Command in EW0 Mode (When Suspend Function Enabled) Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 378 of 450 R8C/2K Group, R8C/2L Group 20. Flash Memory * Block Erase When 20h is first written and then D0h is written to a given block address, an auto-erase operation (erase and verify) of the specified block starts. The FMR00 bit in the FMR0 register can be used to determine whether auto-erasure has completed. The FMR00 bit is set to 0 during auto-erasure and set to 1 when auto-erasure completes. The FMR07 bit in the FMR0 register can be used to determine the result of auto-erasure after auto-erasure has completed (refer to 20.4.2 Status Check Procedure). Also, when the FMR02 bit in the FMR0 register is set to 0 (rewrite disabled), or the FMR02 bit is set to 1 (rewrite enabled) and the FMR15 bit in the FMR1 register is set to 1 (rewrite disabled), block erase commands targeting block 0 are not acknowledged. Do not use the block erase command during program-suspend. In EW0 mode, the MCU enters read status register mode at the same time auto-erasure starts and the status register can be read. In this case, the MCU remains in read status register mode until the next read array command is written. Figure 20.13 shows the Block Erase Command in EW0 Mode (When Suspend Function Disabled). Figure 20.14 shows the Block Erase Command in EW0 Mode (When Suspend Function Enabled). If the programming and erasure endurance is n (n = 100, 1,000, or 10,000), each block can be erased n times. For example, if 1,024 1-byte writes are performed to block A, a 1-Kbyte block, and then the block is erased, the erase count stands at one. When performing 100 or more rewrites, the actual erase count can be reduced by executing programming operations in such a way that all blank areas are used before performing an erase operation. Avoid rewriting only particular blocks and try to average out the programming and erasure endurance of the blocks. It is also advisable to retain data on the erase count of each block and limit the number of erase operations to a certain number. Start Write the command code 20h Write D0h to any block address FMR00 = 1? No Yes Full status check Block erase completed Figure 20.13 Block Erase Command in EW0 Mode (When Suspend Function Disabled) Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 379 of 450 R8C/2K Group, R8C/2L Group 20. Flash Memory Maskable interrupt(1) Start FMR40 = 1 FMR43 = 1 ? No Yes Write the command code 20h FMR41 = 1(3) I = 1 (enable interrupt)(2) FMR46 = 1 ? Write D0h to any block address No Access flash memory Yes Access flash memory FMR00 = 1 ? No FMR41 = 0 Yes Full status check REIT Block erase completed NOTES: 1. In EW0 mode, the interrupt vector table and interrupt routine for interrupts to be used should be allocated to the RAM area. 2. When no interrupt is used, the instruction to enable interrupts is not needed. 3. td(SR-SUS) is needed until erase is suspended after the FMR41 bit in the FMR4 register is set to 1. Figure 20.14 Block Erase Command in EW0 Mode (When Suspend Function Enabled) Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 380 of 450 R8C/2K Group, R8C/2L Group 20.4.3.2 20. Flash Memory Suspend Function The suspend function halts auto-erasure and auto-programming temporarily while these operations are in progress. This function is used for interrupt handling as the user ROM area can be read after the above operations have been suspended. When using erase-suspend or program-suspend in EW0 mode, first check the status of the flash memory in the interrupt routine and then enter erase-suspend or program-suspend. Figure 20.15 shows the Timing of Suspend Operation in EW0 Mode. The procedure for entering erase-suspend during auto-erase operation is as follows: (1) Set the FMR40 bit to 1 (suspend enabled) (2) Set the FMR41 bit to 1 (erase-suspend request). (3) Wait for td (SR-SUS). (4) Confirm that the FMR46 bit is set to 1 (reading enabled) (5) Access the user ROM area. (6) When the FMR41 bit is set to 0 (erasure restarts), auto-erase operation restarts. The procedure for entering program-suspend during auto-programming operation is as follows: (1) Set the FMR40 bit to 1 (suspend enabled) (2) Set the FMR42 bit to 1 (program-suspend request). (3) Wait for td (SR-SUS). (4) Confirm that the FMR46 bit is set to 1 (reading enabled) (5) Access the user ROM area. (6) When the FMR42 bit is set to 0 (programming restarts), auto-programming operation restarts. Erasure starts Erasure suspends Programming Programming Programming Programming Erasure starts suspends restarts(1) ends restarts During erasure FMR00 bit in FMR0 register 1 FMR46 bit in FMR4 register 1 FMR44 bit in FMR4 register 1 FMR43 bit in FMR4 register 1 FMR41 bit in FMR4 register 1 FMR42 bit in FMR4 register 1 During programming During programming Erasure ends During erasure Remains 0 during suspend 0 0 0 Remains 1 during suspend 0 Set to 1 by a program Set to 0 by a program 0 Set to 1 by a program Set to 0 by a program 0 Check that the FMR43 bit is set to 1 (during erase execution), and that the erase-operation has not ended. Check that the FMR44 bit is set to 1 (during program execution), and that the program has not ended. Check the status, and that the programming ends normally. Check the status, and that the erasure ends normally. The above figure shows an example of the use of program-suspend during programming following erase-suspend. NOTE: 1. If program-suspend is entered during erase-suspend, restart programming first. Figure 20.15 Timing of Suspend Operation in EW0 Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 381 of 450 R8C/2K Group, R8C/2L Group 20. Flash Memory Figure 20.16 shows the Program Flowchart during Erase-Suspend in EW0 Mode. (EW0 Mode) Maskable interrupt 1(1) Start FMR40 = 1 FMR43 = 1 ? No Yes Write the command code 20h FMR41 = 1(3) I = 1 (enable interrupt)(2) FMR46 = 1 ? No Write D0h to any block address Yes FMR00 = 1 ? No Yes Write the command code 40h to the write address Write the command code 40h to the write address I = 1 (enable interrupt)(2) I = 1 (enable interrupt)(2) Write data to the write address Write data to the write address Full status check Block erase completed FMR44 = 0 ? No Yes FMR44 = 0 ? No Yes Maskable interrupt 2(1) Full status check FMR44 = 1 ? No Yes Full status check FMR41 = 0 REIT FMR42 = 1(3) FMR46 = 1 ? No Access flash memory Yes Access flash memory FMR42 = 0 REIT NOTES: 1. In EW0 mode, the interrupt vector table and interrupt routine for interrupts to be used should be allocated to the RAM area. 2. When no interrupt is used, the instruction to enable interrupts is not needed. 3. td(SR-SUS) is needed until erase or program is suspended after the FMR41 bit or the FMR42 bit in the FMR4 register is set to 1. Maskable interrupt 1: interrupt in erase-suspend, maskable interrupt 2: interrupt in program-suspend Figure 20.16 Program Flowchart during Erase-Suspend in EW0 Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 382 of 450 R8C/2K Group, R8C/2L Group 20.4.3.3 20. Flash Memory EW0 Mode Interrupts In EW0 mode, maskable interrupts can be used by allocating a vector in RAM. Table 20.5 lists the EW0 Mode Interrupts. Refer to 20.7.1.3 Non-Maskable Interrupts for details of the non-maskable interrupt. Table 20.5 EW0 Mode Interrupts Status During auto-erasure Auto-programming Rev.1.10 Dec 21, 2007 REJ09B0406-0110 When Maskable Interrupt Request is Acknowledged Interrupt handling is executed. Page 383 of 450 R8C/2K Group, R8C/2L Group 20.4.4 20. Flash Memory EW1 Mode The MCU is switched to EW1 mode by setting the FMR11 bit to 1 (EW1 mode) after setting the FMR01 bit to 1 (CPU rewrite mode enabled). The FMR0 register can be used to determine when program and erase operations complete. Figure 20.17 shows the How to Set and Exit EW1 Mode. EW1 Mode Operating Procedure Program in ROM Write 0 to the FMR01 bit before writing 1 (CPU rewrite mode enabled)(1) Write 0 to the FMR11 bit before writing 1 (EW1 mode) Execute software commands Write 0 to the FMR01 bit (CPU rewrite mode disabled) NOTE: 1. To set the FMR01 bit to 1, write 0 to the FMR01 bit before writing 1. Do not generate an interrupt between writing 0 and 1. Figure 20.17 How to Set and Exit EW1 Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 384 of 450 R8C/2K Group, R8C/2L Group 20.4.4.1 20. Flash Memory Software Commands There are four types of software commands: * Read array * Clear status register * Program * Block erase Do not execute read status register command in EW1 mode. Figure 20.18 shows the Software Command Status Transition Diagram in EW1 Mode. Read array mode Reset CPU rewrite disabled (FMR46 = 1 Write 1 to the FMR01 bit immediately after writing 0, and write 1 to the FMR11 bit immediately after writing 0. Reading enabled) No command required Reading only available CPU rewrite mode (EW1 mode) FMR01 = 0 Program suspend Erase suspend Read array mode (FMR46 = 1 Reading enabled) 40h FMR42 = 0 20h FMR41 = 0 (Program command) (Restart) (Block erase command) (Restart) FFh (Read array command) 50h (Clear status register command) Clear ends Program Clear status register Block erase Write data (Programming starts) D0h (Block erasure starts) Interrupt (FMR42 = 1) Interrupt (FMR41 = 1) Auto-program Auto-erase (FMR46 = 0 Reading disabled) (FMR46 = 0 Reading disabled) Auto-programming completed Figure 20.18 CPU stops Auto-erasure completed Software Command Status Transition Diagram in EW1 Mode * Read Array Command The read array command reads the flash memory. When FFh is written to an address in the user ROM area, the MCU enters read array mode. In this mode, the contents of the specified address can be read. Read array mode continues until other commands are written. The MCU enters this mode after a reset is deasserted. * Clear Status Register Command The clear status register command sets the status register to 0. When 50h is written to an address in the user ROM area, bits FMR07 and FMR06 in the FMR0 register and bits SR5 and SR4 in the status register are set to 00b. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 385 of 450 R8C/2K Group, R8C/2L Group 20. Flash Memory * Program Command The program command writes data to the flash memory in 1-byte units. When 40h is written and then data is written to the write address, an auto-program operation (data program and verify) starts. The FMR00 bit in the FMR0 register can be used to determine whether auto-programming has completed. When suspend function disabled, the FMR00 bit is set to 0 during auto-programming and set to 1 when autoprogramming completes. When suspend function enabled, the FMR44 bit is set to 1 during auto-programming and set to 0 when auto-programming completes. The FMR06 bit in the FMR0 register can be used to determine the result of auto-programming after it has been finished (refer to 20.4.2 Status Check Procedure). Do not write additions to the already programmed addresses. Also, when the FMR02 bit in the FMR0 register is set to 0 (rewrite disabled), or the FMR02 bit is set to 1 (rewrite enabled) and the FMR15 bit in the FMR1 register is set to 1 (rewrite disabled), program commands targeting block 0 are not acknowledged. In EW1 mode, do not execute this command for any address which a rewrite control program is allocated. Figure 20.19 shows the Program Command in EW1 Mode (When Suspend Function Disabled). Figure 20.20 shows the Program Command in EW1 Mode (When Suspend Function Enabled). Start Write the command code 40h to the write address Write data to the write address FMR00 = 1? No Yes Full status check Program completed Figure 20.19 Program Command in EW1 Mode (When Suspend Function Disabled) Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 386 of 450 R8C/2K Group, R8C/2L Group 20. Flash Memory Start Maskable interrupt(1) FMR40 = 1 Access flash memory Write the command code 40h REIT I = 1 (enable interrupt) Write data to the write address FMR42 = 0 FMR44 = 0 ? No Yes Full status check Program completed NOTE: 1. td(SR-SUS) is needed until the interrupt request is acknowledged after it is generated. The interrupt to enter suspend should be in interrupt enabled status. Figure 20.20 Program Command in EW1 Mode (When Suspend Function Enabled) Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 387 of 450 R8C/2K Group, R8C/2L Group 20. Flash Memory * Block Erase When 20h is first written and then D0h is written to a given block address, an auto-erase operation (erase and verify) of the specified block starts. The FMR00 bit in the FMR0 register can be used to determine whether auto-erasure has completed. The FMR00 bit is set to 0 during auto-erasure and set to 1 when auto-erasure completes. The FMR07 bit in the FMR0 register can be used to determine the result of auto-erasure after auto-erasure has completed (refer to 20.4.2 Status Check Procedure). Also, when the FMR02 bit in the FMR0 register is set to 0 (rewrite disabled), or the FMR02 bit is set to 1 (rewrite enabled) and the FMR15 bit in the FMR1 register is set to 1 (rewrite disabled), block erase commands targeting block 0 are not acknowledged. Do not use the block erase command during program-suspend. Do not execute this command for any address to which a rewrite control program is allocated. Figure 20.21 shows the Block Erase Command in EW1 Mode (When Suspend Function Disabled). Figure 20.22 shows the Block Erase Command in EW1 Mode (When Suspend Function Enabled). If the programming and erasure endurance is n (n = 100, 1000, or 10,000), each block can be erased n times. For example, if 1,024 1-byte writes are performed to block A, a 1-Kbyte block, and then the block is erased, the erase count stands at one. When performing 100 or more rewrites, the actual erase count can be reduced by executing programming operations in such a way that all blank areas are used before performing an erase operation. Avoid rewriting only particular blocks and try to average out the programming and erasure endurance of the blocks. It is also advisable to retain data on the erase count of each block and limit the number of erase operations to a certain number. Start Write the command code 20h Write D0h to any block address FMR00 = 1? No Yes Full status check Block erase completed Figure 20.21 Block Erase Command in EW1 Mode (When Suspend Function Disabled) Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 388 of 450 R8C/2K Group, R8C/2L Group 20. Flash Memory Start Maskable interrupt(1) FMR40 = 1 Access flash memory Write the command code 20h REIT I = 1 (enable interrupt) Write D0h to any block address FMR41 = 0 FMR00 = 1 ? No Yes Full status check Block erase completed NOTE: 1. td(SR-SUS) is needed until the interrupt request is acknowledged after it is generated. The interrupt to enter suspend should be in interrupt enabled status. Figure 20.22 Block Erase Command in EW1 Mode (When Suspend Function Enabled) Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 389 of 450 R8C/2K Group, R8C/2L Group 20.4.4.2 20. Flash Memory Suspend Function The suspend function halts auto-erasure and auto-programming temporarily while these operations are in progress. This function is used for interrupt handling as the user ROM area can be read after the above operations have been suspended. When the suspend function is used in EW1 mode, the MCU enters erase-suspend or program-suspend after an interrupt request is acknowledged. To enable the suspend function, set the FMR40 bit to 1 (suspend enabled). The interrupt to enter suspend should also be set to enable beforehand. When td (SR-SUS) has elapsed after the interrupt request is generated, the request is acknowledged. When an interrupt request is generated during an erase operation, the FMR41 bit is automatically set to 1 (erasesuspend request) and the auto-erase operation suspends. If an auto-erase operation does not complete (FMR00 bit is 0) after an interrupt process completes, the auto-erase operation restarts by setting the FMR41 bit to 0 (erasure restarts). When an interrupt request is generated during an auto-program operation, the FMR42 bit is automatically set to 1 (program-suspend request) and the auto-program operation suspends. When the auto-program operation does not complete (FMR00 bit is 0) after the interrupt process completes, the auto-program operation can be restarted by setting the FMR42 bit to 0 (programming restarts). Figure 20.23 shows the Timing of Suspend Operation in EW1 Mode. Figure 20.24 shows the Program Flowchart during Erase-Suspend in EW1 Mode. Erasure starts Erasure suspends Programming Programming Programming Programming Erasure starts suspends restarts(1) ends restarts During erasure FMR00 bit in FMR0 register 1 FMR46 bit in FMR4 register 1 FMR44 bit in FMR4 register 1 FMR43 bit in FMR4 register 1 During programming During programming Erasure ends During erasure Remains 0 during suspend 0 0 0 0 Remains 1 during suspend Check that the FMR43 bit is set to 1 (during erase execution), and that the erase-operation has not ended. Check that the FMR44 bit is set to 1 (during program execution), and that the program has not ended. Check the status, and that the programming ends normally. Check the status, and that the erasure ends normally. Set to 0 when interrupt request is acknowledged, or set by a program. IR bit in interrupt control register 1 0 The above figure shows an example of the use of program-suspend during programming following erase-suspend. NOTE: 1. If program-suspend is entered during erase-suspend, restart programming first. Figure 20.23 Timing of Suspend Operation in EW1 Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 390 of 450 R8C/2K Group, R8C/2L Group 20. Flash Memory (EW1 Mode) Start Maskable interrupt 1(1) Maskable interrupt 2(1) FMR40 = 1 Write the command code 40h to the write address Access flash memory Write the command code 20h REIT I = 1 (enable interrupt) I = 1 (enable interrupt) Write data to the write address Write D0h to any block address FMR42 = 0 FMR41 = 0 FMR44 = 0 ? No FMR00 = 1 ? No Yes Full status check Yes Full status check REIT Block erase completed NOTE: 1.td(SR-SUS) is needed until the interrupt request is acknowledged after it is generated. The interrupt to enter suspend should be in interrupt enabled status. Maskable interrupt 1: interrupt in erase-suspend, maskable interrupt 2: interrupt in program-suspend Figure 20.24 20.4.4.3 Program Flowchart during Erase-Suspend in EW1 Mode EW1 Mode Interrupts In EW1 mode, maskable interrupts can be used. Table 20.6 lists the EW1 Mode Interrupts. Refer to 20.7.1.3 Non-Maskable Interrupts for details of the nonmaskable interrupt. Table 20.6 EW1 Mode Interrupts Status During auto-erasure (erasesuspend function enabled) During auto-erasure (erasesuspend function disabled) During auto-programming (program suspend function enabled) During auto- programming (program suspend function disabled) Rev.1.10 Dec 21, 2007 REJ09B0406-0110 When Maskable Interrupt Request is Acknowledged Auto-erasure is suspended after td(SR-SUS) and interrupt handling is executed. Auto-erasure can be restarted by setting the FMR41 bit in theFMR4 register to 0 (erasure restarts) after interrupt handling completes. Auto-erasure has priority and the interrupt request acknowledgement is put on standby. Interrupt handling is executed after auto-erasure completes. Auto-programming is suspended after td(SR-SUS) and interrupt handling is executed. Auto-programming can be restarted by setting the FMR42 bit in the FMR4 register to 0 (programming restarts) after interrupt handling completes. Auto-programming has priority and the interrupt request acknowledgement is put on standby. Interrupt handling is executed after auto-programming completes. Page 391 of 450 R8C/2K Group, R8C/2L Group 20.5 20. Flash Memory Standard Serial I/O Mode In standard serial I/O mode, the user ROM area can be rewritten while the MCU is mounted on-board by using a serial programmer which is suitable for the MCU. There are three types of standard serial I/O modes: * Standard serial I/O mode 1 ..................Clock synchronous serial I/O used to connect with a serial programmer * Standard serial I/O mode 2 ..................Clock asynchronous serial I/O used to connect with a serial programmer * Standard serial I/O mode 3 ..................Special clock asynchronous serial I/O used to connect with a serial programmer This MCU uses standard serial I/O mode 2 and standard serial I/O mode 3. Refer to Appendix 2. Connection Examples between Serial Writer and On-Chip Debugging Emulator. Contact the manufacturer of your serial programmer for details. Refer to the user's manual of your serial programmer for instructions on how to use it. Table 20.7 lists the Pin Functions (Flash Memory Standard Serial I/O Mode 2) and Figure 20.25 shows an Example of Pin Processing in Standard Serial I/O Mode 2. Table 20.8 lists the Pin Functions (Flash Memory Standard Serial I/O Mode 3) and Figure 20.26 shows an Example of Pin Processing in Standard Serial I/O Mode 3. After processing the pins shown in Table 20.8 and rewriting the flash memory using the programmer, apply "H" to the MODE pin and reset the hardware to run a program in the flash memory in single-chip mode. 20.5.1 ID Code Check Function The ID code check function determines whether the ID codes sent from the serial programmer and those written in the flash memory match. Refer to 13. ID Code Areas for details of the ID code check. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 392 of 450 R8C/2K Group, R8C/2L Group Table 20.7 20. Flash Memory Pin Functions (Flash Memory Standard Serial I/O Mode 2) Pin VCC, VSS Name Power input I/O RESET P4_6/XIN P4_7/XOUT P0_1 to P0_3, P0_5 P1_0 to P1_7 P2_0 to P2_7 P3_3 to P3_5 P4_2/VREF MODE P0_0 P4_5 Reset input I P4_6 input/clock input P4_7 input/clock output Input port P0 Input port P1 Input port P2 Input port P3 Input port P4 MODE TXD output RXD input I I/O I I I I I I/O O I Description Apply the voltage guaranteed for programming and erasure to the VCC pin and 0 V to the VSS pin. Reset input pin. Connect a ceramic resonator or crystal oscillator between the XIN and XOUT pins. Input "H" or "L" level signal or leave the pin open. Input "L". Serial data output pin. Serial data input pin. MCU Data output VCC TXD AVCC Data input RXD MODE User reset signal RESET VSS AVSS XIN XOUT Connect an oscillation circuit(2) NOTES: 1. In this example, modes are switched between single-chip mode and standard serial I/O mode by controlling the MODE input with a switch. 2. An oscillator must be connected. Set the main clock frequency to 1 MHz to 20 MHz. Refer to Appendix Figure 2.1 Connection Example with M16C Flash Starter (M3A-0806). Figure 20.25 Example of Pin Processing in Standard Serial I/O Mode 2 Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 393 of 450 R8C/2K Group, R8C/2L Group Table 20.8 20. Flash Memory Pin Functions (Flash Memory Standard Serial I/O Mode 3) Pin VCC, VSS Name Power input I/O Description Apply the voltage guaranteed for programming and erasure to the VCC pin and 0 V to the VSS pin. Reset input pin. RESET P4_6/XIN Reset input I P4_6 input/clock input I Input port P0 Input port P1 Input port P2 Input port P3 Input port P4 MODE I Input "H" or "L" level signal or leave the pin open. I I I I I/O Serial data I/O pin. Connect to the flash programmer. Connect a ceramic resonator or crystal oscillator between the XIN and XOUT pins when connecting P4_7 input/clock output I/O external oscillator. Apply "H" and "L" or leave the pin open when using as input port. P4_7/XOUT P0_0 to P0_3, P0_5 P1_0 to P1_7 P2_0 to P2_7 P3_3 to P3_5 P4_2/VREF, P4_5 MODE MCU MODE I/O MODE VCC AVCC Reset input RESET User reset signal VSS AVSS NOTES: 1. Controlled pins and external circuits vary depending on the programmer. Refer to the programmer manual for details. 2. In this example, modes are switched between single-chip mode and standard serial I/O mode by connecting a programmer. 3. When operating with the on-chip oscillator clock, it is not necessary to connect an oscillating circuit. Figure 20.26 Example of Pin Processing in Standard Serial I/O Mode 3 Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 394 of 450 R8C/2K Group, R8C/2L Group 20.6 20. Flash Memory Parallel I/O Mode Parallel I/O mode is used to input and output software commands, addresses and data necessary to control (read, program, and erase) the on-chip flash memory. Use a parallel programmer which supports this MCU. Contact the manufacturer of the parallel programmer for more information, and refer to the user's manual of the parallel programmer for details on how to use it. ROM areas shown in Figures 20.1 and 20.2 can be rewritten in parallel I/O mode. 20.6.1 ROM Code Protect Function The ROM code protect function disables the reading and rewriting of the flash memory. (Refer to the 20.3.2 ROM Code Protect Function.) Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 395 of 450 R8C/2K Group, R8C/2L Group 20.7 20. Flash Memory Notes on Flash Memory 20.7.1 CPU Rewrite Mode 20.7.1.1 Operating Speed Before entering CPU rewrite mode (EW0 mode), select 5 MHz or below for the CPU clock using the CM06 bit in the CM0 register and bits CM16 to CM17 in the CM1 register. This does not apply to EW1 mode. 20.7.1.2 Prohibited Instructions The following instructions cannot be used in EW0 mode because they reference data in the flash memory: UND, INTO, and BRK. 20.7.1.3 Non-Maskable Interrupts * EW0 Mode Once a watchdog timer, oscillation stop detection, voltage monitor1, or voltage monitor 2 interrupt request is acknowledged, auto-erasure or auto-programming is forcibly stopped immediately and the flash memory is reset. Interrupt handling starts after a fixed period and the flash memory restarts. As the block during auto-erasure or the address during auto-programming is forcibly stopped, the normal value may not be readable. Execute auto-erasure again and ensure it completes normally. The watchdog timer does not stop during command operation, so that interrupt requests may be generated. Initialize the watchdog timer regularly. Do not use the address match interrupt while a command is being executed because the vector of the address match interrupt is allocated in ROM. Do not use a non-maskable interrupt while block 0 is being automatically erased because the fixed vector is allocated in block 0. * EW1 Mode Once a watchdog timer, oscillation stop detection, voltage monitor1, or voltage monitor 2 interrupt request is acknowledged, auto-erasure or auto-programming is forcibly stopped immediately and the flash memory is reset. Interrupt handling starts after a fixed period and the flash memory restarts. As the block during auto-erasure or the address during auto-programming is forcibly stopped, the normal value may not be readable. Execute auto-erasure again and ensure it completes normally. The watchdog timer does not stop even during command operation, so that interrupt requests may be generated. Initialize the watchdog timer by using the erase-suspend function. Do not use the address match interrupt while a command is being executed because the vector of the address match interrupt is allocated in ROM. Do not use a non-maskable interrupt while block 0 is being automatically erased because the fixed vector is allocated in block 0. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 396 of 450 R8C/2K Group, R8C/2L Group 20.7.1.4 20. Flash Memory How to Access Write 0 before writing 1 when setting Bits FMR01, FMR02 in the FMR0 register, or FMR11 bit in the FMR1 register to 1. Do not generate an interrupt between writing 0 and 1. 20.7.1.5 Rewriting User ROM Area In EW0 Mode, if the supply voltage drops while rewriting any block in which a rewrite control program is stored, it may not be possible to rewrite the flash memory because the rewrite control program cannot be rewritten correctly. In this case, use standard serial I/O mode. 20.7.1.6 Program Do not write additions to the already programmed address. 20.7.1.7 Suspend Do not use the block erase command during program-suspend. 20.7.1.8 Entering Stop Mode or Wait Mode Do not enter stop mode or wait mode during erase-suspend. 20.7.1.9 Program and Erase Voltage for Flash Memory To perform programming and erasure, use VCC = 2.7 V to 5.5 V as the supply voltage. Do not perform programming and erasure at less than 2.7 V. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 397 of 450 R8C/2K Group, R8C/2L Group 21. Reducing Power Consumption 21. Reducing Power Consumption 21.1 Overview This chapter describes key points and processing methods for reducing power consumption. 21.2 Key Points and Processing Methods for Reducing Power Consumption Key points for reducing power consumption are shown below. They should be referred to when designing a system or creating a program. 21.2.1 Voltage Detection Circuit When voltage monitor 1 is not used, set the VCA26 bit in the VCA2 register to 0 (voltage detection 1 circuit disabled). When voltage monitor 2 is not used, set the VCA27 bit in the VCA2 register to 0 (voltage detection 2 circuit disabled). If the power-on reset and voltage monitor 0 reset are not used, set the VCA25 bit in the VCA2 register to 0 (voltage detection 0 circuit disabled). 21.2.2 Ports Even after the MCU enters wait mode or stop mode, the states of the I/O ports are retained. Current flows into the output ports in the active state, and shoot-through current flows into the input ports in the high-impedance state. Unnecessary ports should be set to input and fixed to a stable electric potential before the MCU enters wait mode or stop mode. 21.2.3 Clocks Power consumption generally depends on the number of the operating clocks and their frequencies. The fewer the number of operating clocks or the lower their frequencies, the more power consumption decreases. Unnecessary clocks should be stopped accordingly. Stopping XIN clock: CM05 bit in CM0 register Stopping low-speed on-chip oscillator oscillation: CM14 bit in CM1 register Stopping high-speed on-chip oscillator oscillation: HRA00 bit in HRA0 register 21.2.4 Wait Mode, Stop Mode Power consumption can be reduced in wait mode and stop mode. Refer to 10.4 Power Control for details. 21.2.5 Stopping Peripheral Function Clocks If the peripheral function f1, f2, f4, f8, and f32 clocks are not necessary in wait mode, set the CM02 bit in the CM0 register to 1 (peripheral function clock stops in wait mode). This will stop the f1, f2, f4, f8, and f32 clocks in wait mode. 21.2.6 Timers If timer RA is not used, set the TCKCUT bit in the TRAMR register to 1 (count source cutoff). If timer RB is not used, set the TCKCUT bit in the TRBMR register to 1 (count source cutoff). 21.2.7 A/D Converter When A/D conversion is not performed, set the VCUT bit in the ADCON1 register to 0 (VREF unconnected). To perform A/D conversion, wait for at least 1 s after setting the VCUT bit to 1 (VREF connected) before starting the A/D conversion. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 398 of 450 R8C/2K Group, R8C/2L Group 21.2.8 21. Reducing Power Consumption Reducing Internal Power Consumption When the MCU enters wait mode using low-speed on-chip oscillator mode, internal power consumption can be reduced by using the VCA20 bit in the VCA2 register. Figure 21.1 shows the Handling Procedure of Internal Power Low Consumption Using VCA20 Bit. To enable internal power low consumption by the VCA20 bit, follow Figure 21.1 Handling Procedure of Internal Power Low Consumption Using VCA20 Bit. Exit wait mode by interrupt Handling procedure of internal power low consumption enabled by VCA20 bit (Note 1) In interrupt routine Step (1) Enter low-speed on-chip oscillator mode Step (5) VCA20 0 (internal power low consumption disabled)(2) Step (2) Stop XIN clock and high-speed on-chip oscillator clock Step (6) Start XIN clock or high-speed on-chip oscillator clock Step (3) VCA20 1 (internal power low consumption enabled)(2, 3) Step (7) (Wait until XIN clock oscillation stabilizes) Step (4) Enter wait mode(4) Step (8) Enter high-speed clock mode or high-speed on-chip oscillator mode Step (5) VCA20 0 (internal power low consumption disabled)(2) Step (6) Start XIN clock or high-speed on-chip oscillator clock Step (7) (Wait until XIN clock oscillation stabilizes) Step (8) Enter high-speed clock mode or high-speed on-chip oscillator mode If it is necessary to start the high-speed clock or the high-speed on-chip oscillator in the interrupt routine, execute steps (5) to (7) in the interrupt routine. Interrupt handling Step (1) Enter low-speed on-chip oscillator mode Step (2) Stop XIN clock and high-speed on-chip oscillator clock Step (3) VCA20 1 (internal power low consumption enabled)(2, 3) If the high-speed clock or high-speed on-chip oscillator is started in the interrupt routine, execute steps (1) to (3) at the last of the interrupt routine. Interrupt handling completed NOTES: 1. Execute this routine to handle all interrupts generated in wait mode. However, this does not apply if it is not necessary to start the high-speed clock or high-speed on-chip oscillator during the interrupt routine. 2. Do not set the VCA20 bit to 0 with the instruction immediately after setting the VCA20 bit to 1. Also, do not do the opposite. 3. When the VCA20 bit is set to 1, do not set the CM10 bit to 1 (stop mode). 4. When entering wait mode, follow 10.6.2 Wait Mode. VCA20: Bit in VCA2 register Figure 21.1 Handling Procedure of Internal Power Low Consumption Using VCA20 Bit Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 399 of 450 R8C/2K Group, R8C/2L Group 21.2.9 21. Reducing Power Consumption Stopping Flash Memory In low-speed on-chip oscillator mode, power consumption can be further reduced by stopping the flash memory using the FMSTP bit in the FMR0 register. Access to the flash memory is disabled by setting the FMSTP bit to 1 (flash memory stops). The FMSTP bit must be written to by a program transferred to RAM. When the MUC enters stop mode or wait mode while CPU rewrite mode is disabled, the power for the flash memory is automatically turned off. It is turned back on again after the MCU exit stop mode or wait mode. This eliminates the need to set the FMR0 register. Figure 21.2 shows the Handling Procedure Example of Low Power Consumption Using FMSTP Bit. FMSTP bit setting program Transfer FMSTP bit setting program to RAM After writing 0 to FMR01 bit, write 1 (CPU rewrite mode enabled) Write 1 to FMSTP bit (flash memory stops. low power consumption state)(1) Jump to FMSTP bit setting program (The subsequent processing is executed by the program in the RAM) Enter low-speed on-chip oscillator mode Stop high-speed on-chip oscillator Process in low-speed on-chip oscillator mode Switch clock source for CPU clock(2) Write 0 to FMSTP bit (flash memory operates) Write 0 to FMR01 bit (CPU rewrite mode disabled) NOTES: 1. After setting the FMR01 bit to 1 (CPU rewrite mode enabled), set the FMSTP bit to 1 (flash memory stops). 2. Before switching the CPU clock source, make sure the designated clock is stable. 3. Insert a 30 s wait time by a program. Do not access to the flash memory during this wait time. Wait until flash memory circuit stabilizes (30 s)(3) Jump to specified address in flash memory FMR01, FMSTP: Bits in FMR0 register Figure 21.2 Handling Procedure Example of Low Power Consumption Using FMSTP Bit Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 400 of 450 R8C/2K Group, R8C/2L Group 21. Reducing Power Consumption 21.2.10 Low-Current-Consumption Read Mode In low-speed on-chip oscillator mode, the current consumption when reading the flash memory can be reduced by setting the FMR47 bit in the FMR4 register to 1 (enabled). Figure 21.3 shows the Handling Procedure Example of Low-Current-Consumption Read Mode. Handling procedure of low-current-consumption read mode enabled by FMR47 bit Step (1) low-speed on-chip oscillator mode Step (2) Stop high-speed on-chip oscillator clock Step (3) FMR47 1 (low-current-consumption read mode enabled)(1) Step (4) Enter low-current-consumption read mode(2) Step (5) FMR47 0 (low-current-consumption read mode disabled) Step (6) Start high-speed on-chip oscillator clock Step (7) (Wait until high-speed on-chip oscillator clock oscillation stabilizes) Step (8) Enter high-speed on-chip oscillator mode NOTES: 1. To set the FMR47 bit to 1, first write 0 and then write 1 immediately. After writing 0, do not generate an interrupt before writing 1. 2. In low-current-consumption read mode, set the FMR01 bit in the FMR0 register to 0 (CPU rewrite mode disabled). FMR47: Bit in FMR4 register Figure 21.3 Handling Procedure Example of Low-Current-Consumption Read Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 401 of 450 R8C/2K Group, R8C/2L Group 22. Electrical Characteristics 22. Electrical Characteristics The electrical characteristics of N version (Topr = -20C to 85C) and D version (Topr = -40C to 85C) are listed below. Please contact Renesas Technology sales offices for the electrical characteristics in the Y version (Topr = -20C to 105C). Table 22.1 Absolute Maximum Ratings Symbol VCC/AVCC VI VO Pd Topr Parameter Supply voltage Input voltage Output voltage Power dissipation Operating ambient temperature Tstg Storage temperature Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 402 of 450 Condition Topr = 25C Rated Value -0.3 to 6.5 -0.3 to VCC + 0.3 -0.3 to VCC + 0.3 500 -20 to 85 (N version) / -40 to 85 (D version) -65 to 150 Unit V V V mW C C R8C/2K Group, R8C/2L Group Table 22.2 Recommended Operating Conditions Symbol VCC AVCC VSS/AVSS VIH VIL IOH(sum) 22. Electrical Characteristics Parameter f(XIN) Supply voltage Supply voltage Supply voltage Input "H" voltage Input "L" voltage Peak sum output Sum of all pins IOH(peak) "H" current Average sum Sum of all pins IOH(avg) output "H" current Peak output "H" Except P2_0 to P2_7 current P2_0 to P2_7 Average output Except P2_0 to P2_7 "H" current P2_0 to P2_7 Peak sum output Sum of all pins IOL(peak) "L" currents Average sum Sum of all pins IOL(avg) output "L" currents Peak output "L" Except P2_0 to P2_7 currents P2_0 to P2_7 Average output Except P2_0 to P2_7 "L" current P2_0 to P2_7 XIN clock input oscillation frequency - System clock IOH(sum) IOH(peak) IOH(avg) IOL(sum) IOL(sum) IOL(peak) IOL(avg) OCD2 = 0 XlN clock selected OCD2 = 1 On-chip oscillator clock selected Conditions 3.0 V VCC 5.5 V 2.7 V VCC < 3.0 V 2.2 V VCC < 2.7 V 3.0 V VCC 5.5 V 2.7 V VCC < 3.0 V 2.2 V VCC < 2.7 V FRA01 = 0 Low-speed on-chip oscillator clock selected FRA01 = 1 High-speed on-chip oscillator clock selected 3.0 V VCC 5.5 V FRA01 = 1 High-speed on-chip oscillator clock selected 2.7 V VCC 5.5 V FRA01 = 1 High-speed on-chip oscillator clock selected 2.2 V VCC 5.5 V Min. 2.2 2.7 - 0.8 VCC 0 - Standard Typ. - - 0 - - - Max. 5.5 5.5 - VCC 0.2 VCC -160 - - -80 mA - - - - - - - - - - -10 -40 -5 -20 160 mA mA mA mA mA - - 80 mA - - - - 0 0 0 0 0 0 - - - - - - - - - - - 125 10 40 5 20 20 10 5 20 10 5 - mA mA mA mA MHz MHz MHz MHz MHz MHz kHz - - 20 MHz - - 10 MHz - - 5 MHz NOTES: 1. VCC = 2.2 to 5.5 V at Topr = -20 to 85C (N version) / -40 to 85C (D version), unless otherwise specified. 2. The average output current indicates the average value of current measured during 100 ms. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 403 of 450 Unit V V V V mA R8C/2K Group, R8C/2L Group Table 22.3 A/D Converter Characteristics Symbol - - Rladder tconv Vref VIA - 22. Electrical Characteristics Parameter Resolution Absolute accuracy Conditions Vref = AVCC AD = 10 MHz, Vref = AVCC = 5.0 V AD = 10 MHz, Vref = AVCC = 5.0 V AD = 10 MHz, Vref = AVCC = 3.3 V AD = 10 MHz, Vref = AVCC = 3.3 V Vref = AVCC AD = 10 MHz, Vref = AVCC = 5.0 V AD = 10 MHz, Vref = AVCC = 5.0 V 10-bit mode 8-bit mode 10-bit mode 8-bit mode Resistor ladder Conversion time 10-bit mode 8-bit mode Reference voltage Analog input voltage(2) A/D operating Without sample and hold clock frequency With sample and hold Vref = AVCC = 2.7 to 5.5 V Vref = AVCC = 2.7 to 5.5 V Min. - - - - - 10 3.3 2.8 2.2 0 0.25 1 Standard Typ. Max. - 10 - 3 - 2 - 5 - 2 - 40 - - - - - AVCC - AVCC - - 10 10 Unit Bits LSB LSB LSB LSB k s s V V MHz MHz NOTES: 1. AVCC = 2.7 to 5.5 V at Topr = -20 to 85C (N version) / -40 to 85C (D version), unless otherwise specified. 2. When the analog input voltage is over the reference voltage, the A/D conversion result will be 3FFh in 10-bit mode and FFh in 8-bit mode. P0 P1 P2 P3 P4 Figure 22.1 Ports P0 to P4 Timing Measurement Circuit Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 404 of 450 30pF R8C/2K Group, R8C/2L Group Table 22.4 Flash Memory (Program ROM) Electrical Characteristics Symbol - - Parameter Program/erase endurance(2) - Byte program time Block erase time Time delay from suspend request until suspend Interval from erase start/restart until following suspend request Interval from program start/restart until following suspend request Time from suspend until program/erase restart Program, erase voltage Read voltage Program, erase temperature - Data hold time(7) - td(SR-SUS) - - - - - 22. Electrical Characteristics Conditions Min. Standard Typ. - Unit Max. - times R8C/2K Group 100(3) R8C/2L Group 1,000(3) - - - - - times 50 0.4 - s 650 - 400 9 97+CPU clock x 6 cycles - s 0 - - ns - - s 2.7 2.2 0 20 - 3+CPU clock x 4 cycles 5.5 5.5 60 - Ambient temperature = 55C - - - s s V V C year NOTES: 1. VCC = 2.7 to 5.5 V at Topr = 0 to 60C, unless otherwise specified. 2. Definition of programming/erasure endurance The programming and erasure endurance is defined on a per-block basis. If the programming and erasure endurance is n (n = 100 or 10,000), each block can be erased n times. For example, if 1,024 1-byte writes are performed to block A, a 1 Kbyte block, and then the block is erased, the programming/erasure endurance still stands at one. However, the same address must not be programmed more than once per erase operation (overwriting prohibited). 3. Endurance to guarantee all electrical characteristics after program and erase. (1 to Min. value can be guaranteed). 4. In a system that executes multiple programming operations, the actual erasure count can be reduced by writing to sequential addresses in turn so that as much of the block as possible is used up before performing an erase operation. For example, when programming groups of 16 bytes, the effective number of rewrites can be minimized by programming up to 128 groups before erasing them all in one operation. It is also advisable to retain data on the erase count of each block and limit the number of erase operations to a certain number. 5. If an error occurs during block erase, attempt to execute the clear status register command, then execute the block erase command at least three times until the erase error does not occur. 6. Customers desiring program/erase failure rate information should contact their Renesas technical support representative. 7. The data hold time includes time that the power supply is off or the clock is not supplied. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 405 of 450 R8C/2K Group, R8C/2L Group Table 22.5 Flash Memory (Data flash Block A, Block B) Electrical Characteristics(4) Symbol - Parameter - Program/erase endurance(2) Byte program time (program/erase endurance 1,000 times) Byte program time (program/erase endurance > 1,000 times) Block erase time (program/erase endurance 1,000 times) Block erase time (program/erase endurance > 1,000 times) Time delay from suspend request until suspend Interval from erase start/restart until following suspend request Interval from program start/restart until following suspend request Time from suspend until program/erase restart Program, erase voltage Read voltage Program, erase temperature - Data hold time(9) - - - - td(SR-SUS) - - - - - 22. Electrical Characteristics Conditions Min. Unit Max. - times 50 400 s - 65 - s - 0.2 9 s - 0.3 - s - - s 650 - 97+CPU clock x 6 cycles - s 0 - - ns - - s 2.7 2.2 - -20(8) - 3+CPU clock x 4 cycles 5.5 5.5 85 20 - - year 10,000(3) - Ambient temperature = 55 C Standard Typ. - - V V C NOTES: 1. VCC = 2.7 to 5.5 V at Topr = -20 to 85C (N version) / -40 to 85C (D version), unless otherwise specified. 2. Definition of programming/erasure endurance The programming and erasure endurance is defined on a per-block basis. If the programming and erasure endurance is n (n = 100 or 10,000), each block can be erased n times. For example, if 1,024 1-byte writes are performed to block A, a 1 Kbyte block, and then the block is erased, the programming/erasure endurance still stands at one. However, the same address must not be programmed more than once per erase operation (overwriting prohibited). 3. Endurance to guarantee all electrical characteristics after program and erase. (1 to Min. value can be guaranteed). 4. Standard of block A and block B when program and erase endurance exceeds 1,000 times. Byte program time to 1,000 times is the same as that in program ROM. 5. In a system that executes multiple programming operations, the actual erasure count can be reduced by writing to sequential addresses in turn so that as much of the block as possible is used up before performing an erase operation. For example, when programming groups of 16 bytes, the effective number of rewrites can be minimized by programming up to 128 groups before erasing them all in one operation. It is also advisable to retain data on the erase count of each block and limit the number of erase operations to a certain number. 6. If an error occurs during block erase, attempt to execute the clear status register command, then execute the block erase command at least three times until the erase error does not occur. 7. Customers desiring program/erase failure rate information should contact their Renesas technical support representative. 8. -40C for D version. 9. The data hold time includes time that the power supply is off or the clock is not supplied. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 406 of 450 R8C/2K Group, R8C/2L Group 22. Electrical Characteristics Suspend request (maskable interrupt request) FMR46 Clock-dependent time Fixed time Access restart td(SR-SUS) Figure 22.2 Table 22.6 Time delay until Suspend Voltage Detection 0 Circuit Electrical Characteristics Symbol Vdet0 - td(E-A) Vccmin Parameter Voltage detection level Voltage detection circuit self power consumption Waiting time until voltage detection circuit operation starts(2) MCU operating voltage minimum value Condition VCA25 = 1, VCC = 5.0 V Min. 2.2 - - 2.2 Standard Typ. Max. 2.3 2.4 0.9 - - 300 - - Unit V A s V NOTES: 1. The measurement condition is VCC = 2.2 to 5.5 V and Topr = -20 to 85C (N version) / -40 to 85C (D version). 2. Necessary time until the voltage detection circuit operates when setting to 1 again after setting the VCA25 bit in the VCA2 register to 0. Table 22.7 Voltage Detection 1 Circuit Electrical Characteristics Symbol Parameter Vdet1 Voltage detection level(4) - Voltage monitor 1 interrupt request generation time(2) Voltage detection circuit self power consumption Waiting time until voltage detection circuit operation starts(3) - td(E-A) Condition VCA26 = 1, VCC = 5.0 V Min. 2.70 Standard Typ. Max. 2.85 3.00 Unit V - 40 - s - 0.6 - - 100 A - s NOTES: 1. The measurement condition is VCC = 2.2 to 5.5 V and Topr = -20 to 85C (N version) / -40 to 85C (D version). 2. Time until the voltage monitor 1 interrupt request is generated after the voltage passes Vdet1. 3. Necessary time until the voltage detection circuit operates when setting to 1 again after setting the VCA26 bit in the VCA2 register to 0. 4. This parameter shows the voltage detection level when the power supply drops. The voltage detection level when the power supply rises is higher than the voltage detection level when the power supply drops by approximately 0.1 V. Table 22.8 Voltage Detection 2 Circuit Electrical Characteristics Symbol Parameter Vdet2 Voltage detection level - Voltage monitor 2 interrupt request generation time(2) Voltage detection circuit self power consumption Waiting time until voltage detection circuit operation starts(3) - td(E-A) Condition VCA27 = 1, VCC = 5.0 V Min. 3.3 - - - Standard Typ. Max. 3.6 3.9 40 - 0.6 - - 100 Unit V s A s NOTES: 1. The measurement condition is VCC = 2.2 to 5.5 V and Topr = -20 to 85C (N version) / -40 to 85C (D version). 2. Time until the voltage monitor 2 interrupt request is generated after the voltage passes Vdet2. 3. Necessary time until the voltage detection circuit operates after setting to 1 again after setting the VCA27 bit in the VCA2 register to 0. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 407 of 450 R8C/2K Group, R8C/2L Group Table 22.9 Power-on Reset Circuit, Voltage Monitor 0 Reset Electrical Characteristics(3) Symbol Vpor1 22. Electrical Characteristics Parameter Condition Vpor2 Power-on reset valid voltage(4) Power-on reset or voltage monitor 0 reset valid voltage trth External power VCC rise gradient(2) Min. - Standard Typ. - Max. 0.1 0 - Vdet0 V 20 - - mV/msec Unit V NOTES: 1. The measurement condition is Topr = -20 to 85C (N version) / -40 to 85C (D version), unless otherwise specified. 2. This condition (external power VCC rise gradient) does not apply if VCC 1.0 V. 3. To use the power-on reset function, enable voltage monitor 0 reset by setting the LVD0ON bit in the OFS register to 0, the VW0C0 and VW0C6 bits in the VW0C register to 1 respectively, and the VCA25 bit in the VCA2 register to 1. 4. tw(por1) indicates the duration the external power VCC must be held below the effective voltage (Vpor1) to enable a power on reset. When turning on the power for the first time, maintain tw(por1) for 30 s or more if -20C Topr 85C, maintain tw(por1) for 3,000 s or more if -40C Topr < -20C. Vdet0(3) Vdet0(3) 2.2V trth trth External Power VCC Vpor2 Vpor1 Sampling time(1, 2) tw(por1) Internal reset signal ("L" valid) 1 x 32 fOCO-S 1 x 32 fOCO-S NOTES: 1. When using the voltage monitor 0 digital filter, ensure that the voltage is within the MCU operation voltage range (2.2 V or above) during the sampling time. 2. The sampling clock can be selected. Refer to 6. Voltage Detection Circuit for details. 3. Vdet0 indicates the voltage detection level of the voltage detection 0 circuit. Refer to 6. Voltage Detection Circuit for details. Figure 22.3 Reset Circuit Electrical Characteristics Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 408 of 450 R8C/2K Group, R8C/2L Group Table 22.10 22. Electrical Characteristics High-speed On-Chip Oscillator Circuit Electrical Characteristics Symbol Parameter fOCO40M High-speed on-chip oscillator frequency temperature * supply voltage dependence High-speed on-chip oscillator frequency when correction value in FRA7 register is written to FRA1 register(4) - Value in FRA1 register after reset - Oscillation frequency adjustment unit of highspeed on-chip oscillator - - Condition Standard Unit Min. Typ. Max. VCC = 2.7 V to 5.5 V -20C Topr 85C(2) 39.2 40 40.8 MHz VCC = 2.7 V to 5.5 V -40C Topr 85C(2) 39.0 40 41.0 MHz VCC = 2.2 V to 5.5 V -20C Topr 85C(3) 35.2 40 44.8 MHz VCC = 2.2 V to 5.5 V -40C Topr 85C(3) 34.0 40 46.0 MHz - 36.864 - MHz -3% - 3% % VCC = 5.0 V, Topr = 25C VCC = 2.7 V to 5.5 V -20C Topr 85C 08h - F7h - Adjust FRA1 register (value after reset) to -1 - +0.3 - MHz Oscillation stability time VCC = 5.0 V, Topr = 25C - 10 100 s Self power consumption at oscillation VCC = 5.0 V, Topr = 25C - 550 - A NOTES: 1. VCC = 2.2 to 5.5 V, Topr = -20 to 85C (N version) / -40 to 85C (D version), unless otherwise specified. 2. These standard values show when the FRA1 register value after reset is assumed. 3. These standard values show when the corrected value of the FRA6 register is written to the FRA1 register. 4. This enables the setting errors of bit rates such as 9600 bps and 38400 bps to be 0% when the serial interface is used in UART mode. Table 22.11 Low-speed On-Chip Oscillator Circuit Electrical Characteristics Symbol Parameter Condition Standard Min. Typ. Max. Unit fOCO-S Low-speed on-chip oscillator frequency 30 125 250 - Oscillation stability time - 10 100 s - Self power consumption at oscillation - 15 - A VCC = 5.0 V, Topr = 25C kHz NOTE: 1. VCC = 2.2 to 5.5 V, Topr = -20 to 85C (N version) / -40 to 85C (D version), unless otherwise specified. Table 22.12 Power Supply Circuit Timing Characteristics Symbol Parameter Condition Standard Min. Typ. Max. Unit td(P-R) Time for internal power supply stabilization during power-on(2) 1 - 2000 s td(R-S) STOP exit time(3) - - 150 s NOTES: 1. The measurement condition is VCC = 2.2 to 5.5 V and Topr = 25C. 2. Waiting time until the internal power supply generation circuit stabilizes during power-on. 3. Time until system clock supply starts after the interrupt is acknowledged to exit stop mode. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 409 of 450 R8C/2K Group, R8C/2L Group Table 22.13 Electrical Characteristics (1) [VCC = 5 V] Symbol VOH Parameter Output "H" voltage Except P2_0 to P2_7, XOUT P2_0 to P2_7 XOUT VOL Output "L" voltage Except P2_0 to P2_7, XOUT P2_0 to P2_7 XOUT VT+-VT- IIH IIL RPULLUP RfXIN VRAM 22. Electrical Characteristics Hysteresis Condition IOH = -5 mA IOH = -200 A Drive capacity HIGH Drive capacity LOW Drive capacity HIGH Drive capacity LOW IOL = 5 mA IOL = 200 A Drive capacity HIGH Drive capacity LOW Drive capacity HIGH Drive capacity LOW INT0, INT1, INT3, KI0, KI1, KI2, KI3, TRAIO, RXD0, RXD2, CLK0, CLK2 RESET Input "H" current Input "L" current Pull-up resistance Feedback XIN resistance RAM hold voltage VI = 5 V, VCC = 5 V VI = 0 V, VCC = 5 V VI = 0 V, VCC = 5 V During stop mode IOH = -20 mA IOH = -5 mA IOH = -1 mA IOH = -500 A IOL = 20 mA IOL = 5 mA IOL = 1 mA IOL = 500 A Standard Min. Typ. VCC - 2.0 - VCC - 0.5 - VCC - 2.0 - VCC - 2.0 - VCC - 2.0 - VCC - 2.0 - - - - - - - - - - - - - 0.1 0.5 Max. VCC VCC VCC VCC VCC VCC 2.0 0.45 2.0 2.0 2.0 2.0 - Unit V V V V V V V V V V V V V 0.1 1.0 - V - - A - 30 - - 50 1.0 5.0 -5.0 167 - A k M 1.8 - - V NOTE: 1. VCC = 4.2 to 5.5 V at Topr = -20 to 85C (N version) / -40 to 85C (D version), f(XIN) = 20 MHz, unless otherwise specified. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 410 of 450 R8C/2K Group, R8C/2L Group Table 22.14 Symbol ICC 22. Electrical Characteristics Electrical Characteristics (2) [Vcc = 5 V] (Topr = -20 to 85C (N version) / -40 to 85C (D version), unless otherwise specified.) Parameter Condition Power supply High-speed current clock mode (VCC = 3.3 to 5.5 V) Single-chip mode, output pins are open, other pins are VSS High-speed on-chip oscillator mode Low-speed on-chip oscillator mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 XIN = 20 MHz (square wave) High-speed on-chip oscillator off Low-speed on-chip oscillator on = 125 kHz No division Min. - Standard Typ. Max. 10 17 Unit mA XIN = 16 MHz (square wave) High-speed on-chip oscillator off Low-speed on-chip oscillator on = 125 kHz No division - 9 15 mA XIN = 10 MHz (square wave) High-speed on-chip oscillator off Low-speed on-chip oscillator on = 125 kHz No division - 6 - mA XIN = 20 MHz (square wave) High-speed on-chip oscillator off Low-speed on-chip oscillator on = 125 kHz Divide-by-8 - 5 - mA XIN = 16 MHz (square wave) High-speed on-chip oscillator off Low-speed on-chip oscillator on = 125 kHz Divide-by-8 - 4 - mA XIN = 10 MHz (square wave) High-speed on-chip oscillator off Low-speed on-chip oscillator on = 125 kHz Divide-by-8 - 2.5 - mA XIN clock off High-speed on-chip oscillator on fOCO = 20 MHz Low-speed on-chip oscillator on = 125 kHz No division - 10 15 mA XIN clock off High-speed on-chip oscillator on fOCO = 20 MHz Low-speed on-chip oscillator on = 125 kHz Divide-by-8 - 4 - mA XIN clock off High-speed on-chip oscillator on fOCO = 10 MHz Low-speed on-chip oscillator on = 125 kHz No division - 5.5 10 mA XIN clock off High-speed on-chip oscillator on fOCO = 10 MHz Low-speed on-chip oscillator on = 125 kHz Divide-by-8 - 2.5 - mA XIN clock off High-speed on-chip oscillator off Low-speed on-chip oscillator on = 125 kHz Divide-by-8, FMR47 = 1 - 130 300 A Page 411 of 450 R8C/2K Group, R8C/2L Group Table 22.15 Symbol ICC 22. Electrical Characteristics Electrical Characteristics (3) [Vcc = 5 V] (Topr = -20 to 85C (N version) / -40 to 85C (D version), unless otherwise specified.) Parameter Condition Power supply Wait mode current (VCC = 3.3 to 5.5 V) Single-chip mode, output pins are open, other pins are VSS Stop mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 XIN clock off High-speed on-chip oscillator off Low-speed on-chip oscillator on = 125 kHz While a WAIT instruction is executed Peripheral clock operation VCA27 = VCA26 = VCA25 = 0 VCA20 = 1 Min. - Standard Typ. Max. 25 75 Unit A XIN clock off High-speed on-chip oscillator off Low-speed on-chip oscillator on = 125 kHz While a WAIT instruction is executed Peripheral clock off VCA27 = VCA26 = VCA25 = 0 VCA20 = 1 - 23 60 A XIN clock off, Topr = 25C High-speed on-chip oscillator off Low-speed on-chip oscillator off CM10 = 1 Peripheral clock off VCA27 = VCA26 = VCA25 = 0 - 0.8 3.0 A XIN clock off, Topr = 85C High-speed on-chip oscillator off Low-speed on-chip oscillator off CM10 = 1 Peripheral clock off VCA27 = VCA26 = VCA25 = 0 - 1.2 - A Page 412 of 450 R8C/2K Group, R8C/2L Group 22. Electrical Characteristics Timing Requirements (Unless Otherwise Specified: VCC = 5 V, VSS = 0 V at Topr = 25C) [VCC = 5 V] Table 22.16 XIN Input Symbol tc(XIN) tWH(XIN) tWL(XIN) Standard Min. Max. 50 - 25 - 25 - Parameter XIN input cycle time XIN input "H" width XIN input "L" width tC(XIN) Unit ns ns ns VCC = 5 V tWH(XIN) XIN input tWL(XIN) Figure 22.4 Table 22.17 XIN Input Timing Diagram when VCC = 5 V TRAIO Input Symbol tc(TRAIO) tWH(TRAIO) tWL(TRAIO) Standard Min. Max. 100 - 40 - 40 - Parameter TRAIO input cycle time TRAIO input "H" width TRAIO input "L" width tC(TRAIO) tWH(TRAIO) TRAIO input tWL(TRAIO) Figure 22.5 TRAIO Input Timing Diagram when VCC = 5 V Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 413 of 450 Unit ns ns ns VCC = 5 V R8C/2K Group, R8C/2L Group Table 22.18 22. Electrical Characteristics Serial Interface Symbol tc(CK) tW(CKH) tW(CKL) td(C-Q) th(C-Q) tsu(D-C) th(C-D) Standard Min. Max. 200 - 100 - 100 - - 50 0 - 50 - 90 - Parameter CLKi input cycle time CLKi input "H" width CLKi input "L" width TXDi output delay time TXDi hold time RXDi input setup time RXDi input hold time Unit ns ns ns ns ns ns ns i = 0, 2 VCC = 5 V tC(CK) tW(CKH) CLKi tW(CKL) th(C-Q) TXDi td(C-Q) tsu(D-C) th(C-D) RXDi i = 0, 2 Figure 22.6 Table 22.19 Serial Interface Timing Diagram when VCC = 5 V External Interrupt INTi (i = 0, 1, 3) Input tW(INH) INTi input "H" width Standard Min. Max. (1) - 250 tW(INL) INTi input "L" width 250(2) Symbol Parameter - Unit ns ns NOTES: 1. When selecting the digital filter by the INTi input filter select bit, use an INTi input HIGH width of either (1/digital filter clock frequency x 3) or the minimum value of standard, whichever is greater. 2. When selecting the digital filter by the INTi input filter select bit, use an INTi input LOW width of either (1/digital filter clock frequency x 3) or the minimum value of standard, whichever is greater. VCC = 5 V tW(INL) INTi input tW(INH) i = 0, 1, 3 Figure 22.7 External Interrupt INTi Input Timing Diagram when VCC = 5 V Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 414 of 450 R8C/2K Group, R8C/2L Group Table 22.20 Electrical Characteristics (1) [VCC = 3 V] Symbol VOH 22. Electrical Characteristics Parameter Output "H" voltage Except P2_0 to P2_7, XOUT P2_0 to P2_7 XOUT VOL Output "L" voltage Except P2_0 to P2_7, XOUT P2_0 to P2_7 XOUT VT+-VT- Hysteresis IIH IIL RPULLUP RfXIN VRAM Input "H" current Input "L" current Pull-up resistance Feedback resistance RAM hold voltage Condition IOH = -1 mA Standard Min. Typ. VCC - 0.5 - Max. VCC Unit V Drive capacity HIGH Drive capacity LOW Drive capacity HIGH Drive capacity LOW IOL = 1 mA IOH = -5 mA VCC - 0.5 - VCC V IOH = -1 mA VCC - 0.5 - VCC V IOH = -0.1 mA VCC - 0.5 - VCC V IOH = -50 A VCC - 0.5 - VCC V - - 0.5 V Drive capacity HIGH Drive capacity LOW Drive capacity HIGH Drive capacity LOW IOL = 5 mA - - 0.5 V IOL = 1 mA - - 0.5 V IOL = 0.1 mA - - 0.5 V IOL = 50 A - - 0.5 V 0.1 0.3 - V 0.1 0.4 - V - - A - 66 - 1.8 - 160 3.0 - 4.0 -4.0 500 - - INT0, INT1, INT3, KI0, KI1, KI2, KI3, TRAIO, RXD0, RXD2, CLK0, CLK2 RESET VI = 3 V, VCC = 3 V VI = 0 V, VCC = 3 V VI = 0 V, VCC = 3 V XIN During stop mode A k M V NOTE: 1. VCC =2.7 to 3.3 V at Topr = -20 to 85C (N version) / -40 to 85C (D version), f(XIN) = 10 MHz, unless otherwise specified. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 415 of 450 R8C/2K Group, R8C/2L Group Table 22.21 Symbol ICC 22. Electrical Characteristics Electrical Characteristics (2) [Vcc = 3 V] (Topr = -20 to 85C (N version) / -40 to 85C (D version), unless otherwise specified.) Parameter Condition Power supply current High-speed (VCC = 2.7 to 3.3 V) clock mode Single-chip mode, output pins are open, other pins are VSS High-speed on-chip oscillator mode Low-speed on-chip oscillator mode Wait mode Stop mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 XIN = 10 MHz (square wave) High-speed on-chip oscillator off Low-speed on-chip oscillator on = 125 kHz No division XIN = 10 MHz (square wave) High-speed on-chip oscillator off Low-speed on-chip oscillator on = 125 kHz Divide-by-8 XIN clock off High-speed on-chip oscillator on fOCO = 10 MHz Low-speed on-chip oscillator on = 125 kHz No division XIN clock off High-speed on-chip oscillator on fOCO = 10 MHz Low-speed on-chip oscillator on = 125 kHz Divide-by-8 XIN clock off High-speed on-chip oscillator off Low-speed on-chip oscillator on = 125 kHz Divide-by-8, FMR47 = 1 XIN clock off High-speed on-chip oscillator off Low-speed on-chip oscillator on = 125 kHz While a WAIT instruction is executed Peripheral clock operation VCA27 = VCA26 = VCA25 = 0 VCA20 = 1 XIN clock off High-speed on-chip oscillator off Low-speed on-chip oscillator on = 125 kHz While a WAIT instruction is executed Peripheral clock off VCA27 = VCA26 = VCA25 = 0 VCA20 = 1 XIN clock off, Topr = 25C High-speed on-chip oscillator off Low-speed on-chip oscillator off CM10 = 1 Peripheral clock off VCA27 = VCA26 = VCA25 = 0 XIN clock off, Topr = 85C High-speed on-chip oscillator off Low-speed on-chip oscillator off CM10 = 1 Peripheral clock off VCA27 = VCA26 = VCA25 = 0 Page 416 of 450 Min. - Standard Typ. Max. 6 - Unit mA - 2 - mA - 5 9 mA - 2 - mA - 130 300 A - 25 70 A - 23 55 A - 0.7 3.0 A - 1.1 - A R8C/2K Group, R8C/2L Group 22. Electrical Characteristics Timing requirements (Unless Otherwise Specified: VCC = 3 V, VSS = 0 V at Topr = 25C) [VCC = 3 V] Table 22.22 XIN Input Symbol tc(XIN) tWH(XIN) tWL(XIN) Standard Min. Max. 100 - 40 - 40 - Parameter XIN input cycle time XIN input "H" width XIN input "L" width tC(XIN) Unit ns ns ns VCC = 3 V tWH(XIN) XIN input tWL(XIN) Figure 22.8 XIN Input Timing Diagram when VCC = 3 V Table 22.23 TRAIO Input Symbol tc(TRAIO) tWH(TRAIO) tWL(TRAIO) Standard Min. Max. 300 - 120 - 120 - Parameter TRAIO input cycle time TRAIO input "H" width TRAIO input "L" width tC(TRAIO) tWH(TRAIO) TRAIO input tWL(TRAIO) Figure 22.9 TRAIO Input Timing Diagram when VCC = 3 V Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 417 of 450 Unit ns ns ns VCC = 3 V R8C/2K Group, R8C/2L Group Table 22.24 22. Electrical Characteristics Serial Interface Symbol tc(CK) tW(CKH) tW(CKL) td(C-Q) th(C-Q) tsu(D-C) th(C-D) Standard Min. Max. 300 - 150 - 150 - - 80 0 - 70 - 90 - Parameter CLKi input cycle time CLKi input "H" width CLKi Input "L" width TXDi output delay time TXDi hold time RXDi input setup time RXDi input hold time Unit ns ns ns ns ns ns ns i = 0, 2 VCC = 3 V tC(CK) tW(CKH) CLKi tW(CKL) th(C-Q) TXDi td(C-Q) tsu(D-C) th(C-D) RXDi i = 0, 2 Figure 22.10 Table 22.25 Serial Interface Timing Diagram when VCC = 3 V External Interrupt INTi (i = 0, 1, 3) Input tW(INH) INTi input "H" width Standard Min. Max. (1) - 380 tW(INL) INTi input "L" width 380(2) Symbol Parameter Unit - ns ns NOTES: 1. When selecting the digital filter by the INTi input filter select bit, use an INTi input HIGH width of either (1/digital filter clock frequency x 3) or the minimum value of standard, whichever is greater. 2. When selecting the digital filter by the INTi input filter select bit, use an INTi input LOW width of either (1/digital filter clock frequency x 3) or the minimum value of standard, whichever is greater. VCC = 3 V tW(INL) INTi input tW(INH) i = 0, 1, 3 Figure 22.11 External Interrupt INTi Input Timing Diagram when VCC = 3 V Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 418 of 450 R8C/2K Group, R8C/2L Group Table 22.26 Electrical Characteristics (1) [VCC = 2.2 V] Symbol VOH 22. Electrical Characteristics Parameter Output "H" voltage Except P2_0 to P2_7, XOUT P2_0 to P2_7 XOUT VOL Output "L" voltage Except P2_0 to P2_7, XOUT P2_0 to P2_7 XOUT VT+-VT- Hysteresis IIH IIL RPULLUP RfXIN VRAM Input "H" current Input "L" current Pull-up resistance Feedback resistance RAM hold voltage Condition IOH = -1 mA Standard Min. Typ. VCC - 0.5 - Max. VCC IOH = -2 mA VCC - 0.5 - VCC V IOH = -1 mA VCC - 0.5 - VCC V IOH = -0.1 mA VCC - 0.5 - VCC V IOH = -50 A VCC - 0.5 - VCC V - - 0.5 V Drive capacity HIGH Drive capacity LOW Drive capacity HIGH Drive capacity LOW IOL = 2 mA - - 0.5 V IOL = 1 mA - - 0.5 V IOL = 0.1 mA - - 0.5 V IOL = 50 A - - 0.5 V 0.05 0.3 - V 0.05 0.15 - V - - A - 100 - 1.8 - 200 5 - 4.0 -4.0 600 - - INT0, INT1, INT3, KI0, KI1, KI2, KI3, TRAIO, RXD0, RXD2, CLK0, CLK2 VI = 2.2 V VI = 0 V VI = 0 V XIN During stop mode NOTE: 1. VCC = 2.2 V at Topr = -20 to 85C (N version) / -40 to 85C (D version), f(XIN) = 5 MHz, unless otherwise specified. Page 419 of 450 V Drive capacity HIGH Drive capacity LOW Drive capacity HIGH Drive capacity LOW IOL = 1 mA RESET Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Unit A k M V R8C/2K Group, R8C/2L Group Table 22.27 Symbol ICC 22. Electrical Characteristics Electrical Characteristics (2) [Vcc = 2.2 V] (Topr = -20 to 85C (N version) / -40 to 85C (D version), unless otherwise specified.) Parameter Condition Power supply current High-speed (VCC = 2.2 to 2.7 V) clock mode Single-chip mode, output pins are open, other pins are VSS High-speed on-chip oscillator mode Low-speed on-chip oscillator mode Wait mode Stop mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 XIN = 5 MHz (square wave) High-speed on-chip oscillator off Low-speed on-chip oscillator on = 125 kHz No division XIN = 5 MHz (square wave) High-speed on-chip oscillator off Low-speed on-chip oscillator on = 125 kHz Divide-by-8 XIN clock off High-speed on-chip oscillator on fOCO = 5 MHz Low-speed on-chip oscillator on = 125 kHz No division XIN clock off High-speed on-chip oscillator on fOCO = 5 MHz Low-speed on-chip oscillator on = 125 kHz Divide-by-8 XIN clock off High-speed on-chip oscillator off Low-speed on-chip oscillator on = 125 kHz Divide-by-8, FMR47 = 1 XIN clock off High-speed on-chip oscillator off Low-speed on-chip oscillator on = 125 kHz While a WAIT instruction is executed Peripheral clock operation VCA27 = VCA26 = VCA25 = 0 VCA20 = 1 XIN clock off High-speed on-chip oscillator off Low-speed on-chip oscillator on = 125 kHz While a WAIT instruction is executed Peripheral clock off VCA27 = VCA26 = VCA25 = 0 VCA20 = 1 XIN clock off, Topr = 25C High-speed on-chip oscillator off Low-speed on-chip oscillator off CM10 = 1 Peripheral clock off VCA27 = VCA26 = VCA25 = 0 XIN clock off, Topr = 85C High-speed on-chip oscillator off Low-speed on-chip oscillator off CM10 = 1 Peripheral clock off VCA27 = VCA26 = VCA25 = 0 Page 420 of 450 Min. - Standard Typ. Max. 3.5 - Unit mA - 1.5 - mA - 3.5 - mA - 1.5 - mA - 100 230 A - 22 60 A - 20 55 A - 0.7 3.0 A - 1.1 - A R8C/2K Group, R8C/2L Group 22. Electrical Characteristics Timing requirements (Unless Otherwise Specified: VCC = 2.2 V, VSS = 0 V at Topr = 25C) [VCC = 2.2 V] Table 22.28 XIN Input Symbol tc(XIN) tWH(XIN) tWL(XIN) Standard Min. Max. 200 - 90 - 90 - Parameter XIN input cycle time XIN input "H" width XIN input "L" width tC(XIN) Unit ns ns ns VCC = 2.2 V tWH(XIN) XIN input tWL(XIN) Figure 22.12 XIN Input Timing Diagram when VCC = 2.2 V Table 22.29 TRAIO Input Symbol tc(TRAIO) tWH(TRAIO) tWL(TRAIO) Standard Min. Max. 500 - 200 - 200 - Parameter TRAIO input cycle time TRAIO input "H" width TRAIO input "L" width tC(TRAIO) tWH(TRAIO) TRAIO input tWL(TRAIO) Figure 22.13 TRAIO Input Timing Diagram when VCC = 2.2 V Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 421 of 450 Unit ns ns ns VCC = 2.2 V R8C/2K Group, R8C/2L Group Table 22.30 22. Electrical Characteristics Serial Interface Symbol tc(CK) tW(CKH) tW(CKL) td(C-Q) th(C-Q) tsu(D-C) th(C-D) Standard Min. Max. 800 - 400 - 400 - - 200 0 - 150 - 90 - Parameter CLKi input cycle time CLKi input "H" width CLKi input "L" width TXDi output delay time TXDi hold time RXDi input setup time RXDi input hold time Unit ns ns ns ns ns ns ns i = 0, 2 VCC = 2.2 V tC(CK) tW(CKH) CLKi tW(CKL) th(C-Q) TXDi td(C-Q) tsu(D-C) th(C-D) RXDi i = 0, 2 Figure 22.14 Table 22.31 Serial Interface Timing Diagram when VCC = 2.2 V External Interrupt INTi (i = 0, 1, 3) Input INTi input "H" width Standard Min. Max. - 1000(1) INTi input "L" width 1000(2) Symbol tW(INH) tW(INL) Parameter - Unit ns ns NOTES: 1. When selecting the digital filter by the INTi input filter select bit, use an INTi input HIGH width of either (1/digital filter clock frequency x 3) or the minimum value of standard, whichever is greater. 2. When selecting the digital filter by the INTi input filter select bit, use an INTi input LOW width of either (1/digital filter clock frequency x 3) or the minimum value of standard, whichever is greater. VCC = 2.2 V tW(INL) INTi input tW(INH) i = 0, 1, 3 Figure 22.15 External Interrupt INTi Input Timing Diagram when VCC = 2.2 V Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 422 of 450 R8C/2K Group, R8C/2L Group 23. Usage Notes 23. Usage Notes 23.1 Notes on Clock Generation Circuit 23.1.1 Stop Mode When entering stop mode, set the FMR01 bit in the FMR0 register to 0 (CPU rewrite mode disabled) and the CM10 bit in the CM1 register to 1 (stop mode). An instruction queue pre-reads 4 bytes from the instruction which sets the CM10 bit to 1 (stop mode) and the program stops. Insert at least 4 NOP instructions following the JMP.B instruction after the instruction which sets the CM10 bit to 1. * Program example to enter stop mode BCLR BSET FSET BSET JMP.B LABEL_001 : NOP NOP NOP NOP 23.1.2 1,FMR0 0,PRCR I 0,CM1 LABEL_001 ; CPU rewrite mode disabled ; Protect disabled ; Enable interrupt ; Stop mode Wait Mode When entering wait mode, set the FMR01 bit in the FMR0 register to 0 (CPU rewrite mode disabled) and execute the WAIT instruction. An instruction queue pre-reads 4 bytes from the WAIT instruction and the program stops. Insert at least 4 NOP instructions after the WAIT instruction. * Program example to execute the WAIT instruction BCLR 1,FMR0 FSET I WAIT NOP NOP NOP NOP 23.1.3 ; CPU rewrite mode disabled ; Enable interrupt ; Wait mode Oscillation Stop Detection Function Since the oscillation stop detection function cannot be used if the XIN clock frequency is 2 MHz or below, set bits OCD1 to OCD0 to 00b. 23.1.4 Oscillation Circuit Constants Ask the manufacturer of the oscillator to specify the best oscillation circuit constants for your system. To use this MCU with supply voltage below VCC = 2.7 V, it is recommended to set the CM11 bit in the CM1 register to 1 (on-chip feedback resistor disabled), the CM15 bit to 1 (high drive capacity), and connect the feedback resistor to the chip externally. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 423 of 450 R8C/2K Group, R8C/2L Group 23.2 23. Usage Notes Notes on Interrupts 23.2.1 Reading Address 00000h Do not read address 00000h by a program. When a maskable interrupt request is acknowledged, the CPU reads interrupt information (interrupt number and interrupt request level) from 00000h in the interrupt sequence. At this time, the acknowledged interrupt IR bit is set to 0. If address 00000h is read by a program, the IR bit for the interrupt which has the highest priority among the enabled interrupts is set to 0. This may cause the interrupt to be canceled, or an unexpected interrupt to be generated. 23.2.2 SP Setting Set any value in the SP before an interrupt is acknowledged. The SP is set to 0000h after reset. Therefore, if an interrupt is acknowledged before setting a value in the SP, the program may run out of control. 23.2.3 External Interrupt and Key Input Interrupt Either "L" level or an "H" level of width shown in the Electrical Characteristics is necessary for the signal input to pins INT0, INT1, INT3 and pins KI0 to KI3, regardless of the CPU clock. For details, refer to Table 22.19 (VCC = 5V), Table 22.25 (VCC = 3V), Table 22.31 (VCC = 2.2V) External Interrupt INTi (i = 0, 1, 3) Input. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 424 of 450 R8C/2K Group, R8C/2L Group 23.2.4 23. Usage Notes Changing Interrupt Sources The IR bit in the interrupt control register may be set to 1 (interrupt requested) when the interrupt source changes. When using an interrupt, set the IR bit to 0 (no interrupt requested) after changing the interrupt source. In addition, changes of interrupt sources include all factors that change the interrupt sources assigned to individual software interrupt numbers, polarities, and timing. Therefore, if a mode change of a peripheral function involves interrupt sources, edge polarities, and timing, set the IR bit to 0 (no interrupt requested) after the change. Refer to the individual peripheral function for its related interrupts. Figure 23.1 shows an Example of Procedure for Changing Interrupt Sources. Interrupt source change Disable interrupts(2, 3) Change interrupt source (including mode of peripheral function) Set the IR bit to 0 (interrupt not requested) using the MOV instruction(3) Enable interrupts (2, 3) Change completed IR bit: The interrupt control register bit of an interrupt whose source is changed. NOTES: 1. Execute the above settings individually. Do not execute two or more settings at once (by one instruction). 2. To prevent interrupt requests from being generated disable the peripheral function before changing the interrupt source. In this case, use the I flag if all maskable interrupts can be disabled. If all maskable interrupts cannot be disabled, use bits ILVL0 to ILVL2 of the interrupt whose source is changed. 3. Refer to 12.6.5 Changing Interrupt Control Register Contents for the instructions to be used and usage notes. Figure 23.1 Example of Procedure for Changing Interrupt Sources Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 425 of 450 R8C/2K Group, R8C/2L Group 23.2.5 23. Usage Notes Changing Interrupt Control Register Contents (a) The contents of an interrupt control register can only be changed while no interrupt requests corresponding to that register are generated. If interrupt requests may be generated, disable interrupts before changing the interrupt control register contents. (b) When changing the contents of an interrupt control register after disabling interrupts, be careful to choose appropriate instructions. Changing any bit other than IR bit If an interrupt request corresponding to a register is generated while executing the instruction, the IR bit may not be set to 1 (interrupt requested), and the interrupt request may be ignored. If this causes a problem, use the following instructions to change the register: AND, OR, BCLR, BSET Changing IR bit If the IR bit is set to 0 (interrupt not requested), it may not be set to 0 depending on the instruction used. Therefore, use the MOV instruction to set the IR bit to 0. (c) When disabling interrupts using the I flag, set the I flag as shown in the sample programs below. Refer to (b) regarding changing the contents of interrupt control registers by the sample programs. Sample programs 1 to 3 are for preventing the I flag from being set to 1 (interrupts enabled) before the interrupt control register is changed for reasons of the internal bus or the instruction queue buffer. Example 1: Use NOP instructions to prevent I flag from being set to 1 before interrupt control register is changed INT_SWITCH1: FCLR I ; Disable interrupts AND.B #00H,0056H ; Set TRAIC register to 00h NOP ; NOP FSET I ; Enable interrupts Example 2: Use dummy read to delay FSET instruction INT_SWITCH2: FCLR I ; Disable interrupts AND.B #00H,0056H ; Set TRAIC register to 00h MOV.W MEM,R0 ; Dummy read FSET I ; Enable interrupts Example 3: Use POPC instruction to change I flag INT_SWITCH3: PUSHC FLG FCLR I ; Disable interrupts AND.B #00H,0056H ; Set TRAIC register to 00h POPC FLG ; Enable interrupts Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 426 of 450 R8C/2K Group, R8C/2L Group 23.3 23. Usage Notes Notes on Timers 23.3.1 Notes on Timer RA * Timer RA stops counting after a reset. Set the values in the timer RA and timer RA prescalers before the count starts. * Even if the prescaler and timer RA are read out in 16-bit units, these registers are read 1 byte at a time by the MCU. Consequently, the timer value may be updated during the period when these two registers are being read. * In pulse period measurement mode, bits TEDGF and TUNDF in the TRACR register can be set to 0 by writing 0 to these bits by a program. However, these bits remain unchanged if 1 is written. When using the READ-MODIFY-WRITE instruction for the TRACR register, the TEDGF or TUNDF bit may be set to 0 although these bits are set to 1 while the instruction is being executed. In this case, write 1 to the TEDGF or TUNDF bit which is not supposed to be set to 0 with the MOV instruction. * When changing to pulse period measurement mode from another mode, the contents of bits TEDGF and TUNDF are undefined. Write 0 to bits TEDGF and TUNDF before the count starts. * The TEDGF bit may be set to 1 by the first timer RA prescaler underflow generated after the count starts. * When using the pulse period measurement mode, leave two or more periods of the timer RA prescaler immediately after the count starts, then set the TEDGF bit to 0. * The TCSTF bit retains 0 (count stops) for 0 to 1 cycle of the count source after setting the TSTART bit to 1 (count starts) while the count is stopped. During this time, do not access registers associated with timer RA(1) other than the TCSTF bit. Timer RA starts counting at the first valid edge of the count source after The TCSTF bit is set to 1 (during count). The TCSTF bit remains 1 for 0 to 1 cycle of the count source after setting the TSTART bit to 0 (count stops) while the count is in progress. Timer RA counting is stopped when the TCSTF bit is set to 0. During this time, do not access registers associated with timer RA(1) other than the TCSTF bit. NOTE: 1.Registers associated with timer RA: TRACR, TRAIOC, TRAMR, TRAPRE, and TRA. * When the TRAPRE register is continuously written during count operation (TCSTF bit is set to 1), allow three or more cycles of the count source clock for each write interval. * When the TRA register is continuously written during count operation (TCSTF bit is set to 1), allow three or more cycles of the prescaler underflow for each write interval. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 427 of 450 R8C/2K Group, R8C/2L Group 23.3.2 23. Usage Notes Notes on Timer RB * Timer RB stops counting after a reset. Set the values in the timer RB and timer RB prescalers before the count starts. * Even if the prescaler and timer RB is read out in 16-bit units, these registers are read 1 byte at a time by the MCU. Consequently, the timer value may be updated during the period when these two registers are being read. * In programmable one-shot generation mode and programmable wait one-shot generation mode, when setting the TSTART bit in the TRBCR register to 0, 0 (stops counting) or setting the TOSSP bit in the TRBOCR register to 1 (stops one-shot), the timer reloads the value of reload register and stops. Therefore, in programmable one-shot generation mode and programmable wait one-shot generation mode, read the timer count value before the timer stops. * The TCSTF bit remains 0 (count stops) for 1 to 2 cycles of the count source after setting the TSTART bit to 1 (count starts) while the count is stopped. During this time, do not access registers associated with timer RB(1) other than the TCSTF bit. Timer RB starts counting at the first valid edge of the count source after the TCSTF bit is set to 1 (during count). The TCSTF bit remains 1 for 1 to 2 cycles of the count source after setting the TSTART bit to 0 (count stops) while the count is in progress. Timer RB counting is stopped when the TCSTF bit is set to 0. During this time, do not access registers associated with timer RB(1) other than the TCSTF bit. NOTE: 1.Registers associated with timer RB: TRBCR, TRBOCR, TRBIOC, TRBMR, TRBPRE, TRBSC, and TRBPR. * If the TSTOP bit in the TRBCR register is set to 1 during timer operation, timer RB stops immediately. * If 1 is written to the TOSST or TOSSP bit in the TRBOCR register, the value of the TOSSTF bit changes after one or two cycles of the count source have elapsed. If the TOSSP bit is written to 1 during the period between when the TOSST bit is written to 1 and when the TOSSTF bit is set to 1, the TOSSTF bit may be set to either 0 or 1 depending on the content state. Likewise, if the TOSST bit is written to 1 during the period between when the TOSSP bit is written to 1 and when the TOSSTF bit is set to 0, the TOSSTF bit may be set to either 0 or 1. 23.3.2.1 Timer mode The following workaround should be performed in timer mode. To write to registers TRBPRE and TRBPR during count operation (TCSTF bit is set to 1), note the following points: * When the TRBPRE register is written continuously, allow three or more cycles of the count source for each write interval. * When the TRBPR register is written continuously, allow three or more cycles of the prescaler underflow for each write interval. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 428 of 450 R8C/2K Group, R8C/2L Group 23.3.2.2 23. Usage Notes Programmable waveform generation mode The following three workarounds should be performed in programmable waveform generation mode. (1) To write to registers TRBPRE and TRBPR during count operation (TCSTF bit is set to 1), note the following points: * When the TRBPRE register is written continuously, allow three or more cycles of the count source for each write interval. * When the TRBPR register is written continuously, allow three or more cycles of the prescaler underflow for each write interval. (2) To change registers TRBPRE and TRBPR during count operation (TCSTF bit is set to 1), synchronize the TRBO output cycle using a timer RB interrupt, etc. This operation should be preformed only once in the same output cycle. Also, make sure that writing to the TRBPR register does not occur during period A shown in Figures 23.2 and 23.3. The following shows the detailed workaround examples. * Workaround example (a): As shown in Figure 23.2, write to registers TRBSC and TRBPR in the timer RB interrupt routine. These write operations must be completed by the beginning of period A. Period A Count source/ prescaler underflow signal TRBO pin output IR bit in TRBIC register Primary period (a) Interrupt request is acknowledged Secondary period Ensure sufficient time (b) Interrupt request is generated Interrupt Instruction in sequence interrupt routine Set the secondary and then the primary register immediately (a) Period between interrupt request generation and the completion of execution of an instruction. The length of time varies depending on the instruction being executed. The DIVX instruction requires the longest time, 30 cycles (assuming no wait states and that a register is set as the divisor). (b) 20 cycles. 21 cycles for address match and single-step interrupts. Figure 23.2 Workaround Example (a) When Timer RB interrupt is Used Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 429 of 450 R8C/2K Group, R8C/2L Group 23. Usage Notes * Workaround example (b): As shown in Figure 23.3 detect the start of the primary period by the TRBO pin output level and write to registers TRBSC and TRBPR. These write operations must be completed by the beginning of period A. If the port register's bit value is read after the port direction register's bit corresponding to the TRBO pin is set to 0 (input mode), the read value indicates the TRBO pin output value. Period A Count source/ prescaler underflow signal TRBO pin output Read value of the port register's bit corresponding to the TRBO pin (when the bit in the port direction register is set to 0) Primary period Secondary period (i) (ii) (iii) Ensure sufficient time The TRBO output inversion is detected at the end of the secondary period. Figure 23.3 Upon detecting (i), set the secondary and then the primary register immediately. Workaround Example (b) When TRBO Pin Output Value is Read (3) To stop the timer counting in the primary period, use the TSTOP bit in the TRBCR register. In this case, registers TRBPRE and TRBPR are initialized and their values are set to the values after reset. 23.3.2.3 Programmable one-shot generation mode The following two workarounds should be performed in programmable one-shot generation mode. (1) To write to registers TRBPRE and TRBPR during count operation (TCSTF bit is set to 1), note the following points: * When the TRBPRE register is written continuously during count operation (TCSTF bit is set to 1), allow three or more cycles of the count source for each write interval. * When the TRBPR register is written continuously during count operation (TCSTF bit is set to 1), allow three or more cycles of the prescaler underflow for each write interval. (2) Do not set both the TRBPRE and TRBPR registers to 00h. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 430 of 450 R8C/2K Group, R8C/2L Group 23.3.2.4 23. Usage Notes Programmable wait one-shot generation mode The following three workarounds should be performed in programmable wait one-shot generation mode. (1) To write to registers TRBPRE and TRBPR during count operation (TCSTF bit is set to 1), note the following points: * When the TRBPRE register is written continuously, allow three or more cycles of the count source for each write interval. * When the TRBPR register is written continuously, allow three or more cycles of the prescaler underflow for each write interval. (2) Do not set both the TRBPRE and TRBPR registers to 00h. (3) Set registers TRBSC and TRBPR using the following procedure. (a) To use "INT0 pin one-shot trigger enabled" as the count start condition Set the TRBSC register and then the TRBPR register. At this time, after writing to the TRBPR register, allow an interval of 0.5 or more cycles of the count source before trigger input from the INT0 pin. (b) To use "writing 1 to TOSST bit" as the start condition Set the TRBSC register, the TRBPR register, and then TOSST bit. At this time, after writing to the TRBPR register, allow an interval of 0.5 or more cycles of the count source before writing to the TOSST bit. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 431 of 450 R8C/2K Group, R8C/2L Group 23.3.3 23. Usage Notes Notes on Timer RC 23.3.3.1 TRC Register * The following note applies when the CCLR bit in the TRCCR1 register is set to 1 (clear TRC register at compare match with TRCGRA register). When using a program to write a value to the TRC register while the TSTART bit in the TRCMR register is set to 1 (count starts), ensure that the write does not overlap with the timing with which the TRC register is set to 0000h. If the timing of the write to the TRC register and the setting of the TRC register to 0000h coincide, the write value will not be written to the TRC register and the TRC register will be set to 0000h. * Reading from the TRC register immediately after writing to it can result in the value previous to the write being read out. To prevent this, execute the JMP.B instruction between the read and the write instructions. Program Example MOV.W #XXXXh, TRC ;Write JMP.B L1 ;JMP.B instruction L1: MOV.W TRC,DATA ;Read 23.3.3.2 TRCSR Register Reading from the TRCSR register immediately after writing to it can result in the value previous to the write being read out. To prevent this, execute the JMP.B instruction between the read and the write instructions. Program Example MOV.B #XXh, TRCSR ;Write JMP.B L1 ;JMP.B instruction L1: MOV.B TRCSR,DATA ;Read 23.3.3.3 Count Source Switching * Stop the count before switching the count source. Switching procedure (1) Set the TSTART bit in the TRCMR register to 0 (count stops). (2) Change the settings of bits TCK2 to TCK0 in the TRCCR1 register. * After switching the count source from fOCO40M to another clock, allow a minimum of two cycles of f1 to elapse after changing the clock setting before stopping fOCO40M. Switching procedure (1) Set the TSTART bit in the TRCMR register to 0 (count stops). (2) Change the settings of bits TCK2 to TCK0 in the TRCCR1 register. (3) Wait for a minimum of two cycles of f1. (4) Set the FRA00 bit in the FRA0 register to 0 (high-speed on-chip oscillator off). 23.3.3.4 Input Capture Function * The pulse width of the input capture signal should be three cycles or more of the timer RC operation clock (refer to Table 16.11 Timer RC Operation Clock). * The value of the TRC register is transferred to the TRCGRj register one or two cycles of the timer RC operation clock after the input capture signal is input to the TRCIOj (j = A, B, C, or D) pin (when the digital filter function is not used). 23.3.3.5 TRCMR Register in PWM2 Mode When the CSEL bit in the TRCCR2 register is set to 1 (count stops at compare match with the TRCGRA register), do not set the TRCMR register at compare match timing of registers TRC and TRCGRA. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 432 of 450 R8C/2K Group, R8C/2L Group 23.3.4 23. Usage Notes Notes on Timer RD 23.3.4.1 TRDSTR Register * Set the TRDSTR register using the MOV instruction. * When the CSELi (i = 0 to 1) is set to 0 (the count stops at compare match of registers TRDi and TRDGRAi), the count does not stop and the TSTARTi bit remains unchanged even if 0 (count stops) is written to the TSTARTi bit. * Therefore, set the TSTARTi bit to 0 to change other bits without changing the TSTARTi bit when the CSELi bit is se to 0. * To stop counting by a program, set the TSTARTi bit after setting the CSELi bit to 1. Although the CSELi bit is set to 1 and the TSTARTi bit is set to 0 at the same time (with 1 instruction), the count cannot be stopped. * Table 23.1 lists the TRDIOji (j = A, B, C, or D) Pin Output Level when Count Stops to use the TRDIOji (j = A, B, C, or D) pin with the timer RD output. Table 23.1 TRDIOji (j = A, B, C, or D) Pin Output Level when Count Stops Count Stop When the CSELi bit is set to 1, set the TSTARTi bit to 0 and the count stops. When the CSELi bit is set to 0, the count stops at compare match of registers TRDi and TRDGRAi. 23.3.4.2 TRDIOji Pin Output when Count Stops Hold the output level immediately before the count stops. Hold the output level after output changes by compare match. TRDi Register (i = 0 or 1) * When writing the value to the TRDi register by a program while the TSTARTi bit in the TRDSTR register is set to 1 (count starts), avoid overlapping with the timing for setting the TRDi register to 0000h, and then write. If the timing for setting the TRDi register to 0000h overlaps with the timing for writing the value to the TRDi register, the value is not written and the TRDi register is set to 0000h. These precautions are applicable when selecting the following by bits CCLR2 to CCLR0 in the TRDCRi register. - 001b (Clear by the TRDi register at compare match with the TRDGRAi register.) - 010b (Clear by the TRDi register at compare match with the TRDGRBi register.) - 011b (Synchronous clear) - 101b (Clear by the TRDi register at compare match with the TRDGRCi register.) - 110b (Clear by the TRDi register at compare match with the TRDGRDi register.) * When writing the value to the TRDi register and continuously reading the same register, the value before writing may be read. In this case, execute the JMP.B instruction between the writing and reading. Program example MOV.W #XXXXh, TRD0 ;Writing JMP.B L1 ;JMP.B L1: MOV.W TRD0,DATA ;Reading 23.3.4.3 TRDSRi Register (i = 0 or 1) When writing the value to the TRDSRi register and continuously reading the same register, the value before writing may be read. In this case, execute the JMP.B instruction between the writing and reading. Program example MOV.B #XXh, TRDSR0 ;Writing JMP.B L1 ;JMP.B L1: MOV.B TRDSR0,DATA ;Reading Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 433 of 450 R8C/2K Group, R8C/2L Group 23.3.4.4 23. Usage Notes Count Source Switch * Switch the count source after the count stops. Change procedure (1) Set the TSTARTi (i = 0 or 1) bit in the TRDSTR register to 0 (count stops). (2) Change bits TCK2 to TCK0 in the TRDCRi register. * When changing the count source from fOCO40M to another source and stopping fOCO40M, wait 2 cycles of f1 or more after setting the clock switch, and then stop fOCO40M. Change procedure (1) Set the TSTARTi (i = 0 or 1) bit in the TRDSTR register to 0 (count stops). (2) Change bits TCK2 to TCK0 in the TRDCRi register. (3) Wait 2 or more cycles of f1. (4) Set the FRA00 bit in the FRA0 register to 0 (high-speed on-chip oscillator stops). 23.3.4.5 Input Capture Function * Set the pulse width of the input capture signal to 3 or more cycles of the timer RD operation clock (refer to Table 16.25 Timer RD Operation Clocks). * The value in the TRDi register is transferred to the TRDGRji register 2 to 3 cycles of the timer RD operation clock after the input capture signal is applied to the TRDIOji pin (i = 0 or 1, j = either A, B, C, or D) (no digital filter). 23.3.4.6 Reset Synchronous PWM Mode * When reset synchronous PWM mode is used for motor control, make sure OLS0 = OLS1. * Set to reset synchronous PWM mode by the following procedure: Change procedure (1) Set the TSTART0 bit in the TRDSTR register to 0 (count stops). (2) Set bits CMD1 to CMD0 in the TRDFCR register to 00b (timer mode, PWM mode, and PWM3 mode). (3) Set bits CMD1 to CMD0 to 01b (reset synchronous PWM mode). (4) Set the other registers associated with timer RD again. 23.3.4.7 Complementary PWM Mode * When complementary PWM mode is used for motor control, make sure OLS0 = OLS1. * Change bits CMD1 to CMD0 in the TRDFCR register in the following procedure. Change procedure: When setting to complementary PWM mode (including re-set), or changing the transfer timing from the buffer register to the general register in complementary PWM mode. (1) Set both the TSTART0 and TSTART1 bits in the TRDSTR register to 0 (count stops). (2) Set bits CMD1 to CMD0 in the TRDFCR register to 00b (timer mode, PWM mode, and PWM3 mode). (3) Set bits CMD1 to CMD0 to 10b or 11b (complementary PWM mode). (4) Set the registers associated with other timer RD again. Change procedure: When stopping complementary PWM mode (1) Set both the TSTART0 and TSTART1 bits in the TRDSTR register to 0 (count stops). (2) Set bits CMD1 to CMD to 00b (timer mode, PWM mode, and PWM3 mode). * Do not write to TRDGRA0, TRDGRB0, TRDGRA1, or TRDGRB1 register during operation. When changing the PWM waveform, transfer the values written to registers TRDGRD0, TRDGRC1, and TRDGRD1 to registers TRDGRB0, TRDGRA1, and TRDGRB1 using the buffer operation. However, to write data to the TRDGRD0, TRDGRC1, or TRDGRD1 register, set bits BFD0, BFC1, and BFD1 to 0 (general register). After this, bits BFD0, BFC1, and BFD1 may be set to 1 (buffer register). The PWM period cannot be changed. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 434 of 450 R8C/2K Group, R8C/2L Group 23. Usage Notes * If the value in the TRDGRA0 register is assumed to be m, the TRD0 register counts m-1, m, m+1, m, m-1, in that order, when changing from increment to decrement operation. When changing from m to m+1, the IMFA bit is set to 1. Also, bits CMD1 to CMD0 in the TRDFCR register are set to 11b (complementary PWM mode, buffer data transferred at compare match between registers TRD0 and TRDGRA0), the content in the buffer registers (TRDGRD0, TRDGRC1, and TRDGRD1) is transferred to the general registers (TRDGRB0, TRDGRA1, and TRDGRB1). During m+1, m, and m-1 operation, the IMFA bit remains unchanged and data are not transferred to registers such as the TRDGRA0 register. Count value in TRD0 register m+1 Setting value in TRDGRA0 register m Set to 0 by a program IMFA bit in TRDSR0 register No change 1 0 Transferred from buffer register When bits CMD1 to CMD0 in the TRDFCR register are set to 11b (transfer from the buffer register to the general register at compare match of between registers TRD0 and TRDGRA0). TRDGRB0 register TRDGRA1 register TRDGRB1 register Figure 23.4 Not transferred from buffer register Operation at Compare Match between Registers TRD0 and TRDGRA0 in Complementary PWM Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 435 of 450 R8C/2K Group, R8C/2L Group 23. Usage Notes * The TRD1 register counts 1, 0, FFFFh, 0, 1, in that order, when changing from decrement to increment operation. The UDF bit is set to 1 when changing between 1, 0, and FFFFh operation. Also, when bits CMD1 to CMD0 in the TRDFCR register are set to 10b (complementary PWM mode, buffer data transferred at underflow in the TRD1 register), the content in the buffer registers (TRDGRD0, TRDGRC1, and TRDGRD1) is transferred to the general registers (TRDGRB0, TRDGRA1, and TRDGRB1). During FFFFh, 0, 1 operation, data are not transferred to registers such as the TRDGRB0 register. Also, at this time, the OVF bit remains unchanged. Count value in TRD0 register 1 0 FFFFh Set to 0 by a program UDF bit in TRDSR0 register 1 OVF bit in TRDSR0 register 1 0 No change 0 Transferred from buffer register TRDGRB0 register TRDGRA1 register TRDGRB1 register Figure 23.5 Not transferred from buffer register When bits CMD1 to CMD0 in the TRDFCR register are set to 10b (transfer from the buffer register to the general register when the TRD1 register underflows). Operation when TRD1 Register Underflows in Complementary PWM Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 436 of 450 R8C/2K Group, R8C/2L Group 23. Usage Notes * Select with bits CMD1 to CMD0 the timing of data transfer from the buffer register to the general register. However, transfer takes place with the following timing in spite of the value of bits CMD1 to CMD0 in the following cases: Value in buffer register value in TRDGRA0 register: Transfer take place at underflow of the TRD1 register. After this, when the buffer register is set to 0001h or above and a smaller value than the value of the TRDGRA0 register, and the TRD1 register underflows for the first time after setting, the value is transferred to the general register. After that, the value is transferred with the timing selected by bits CMD1 to CMD0. n3 m+1 Count value in TRD0 register n2 n1 Count value in TRD1 register 0000h TRDGRD0 register n2 n1 Transfer with timing set by bits CMD1 to CMD0 n2 n1 Transfer Transfer Transfer TRDGRB0 register n2 n3 n3 Transfer at underflow of TRD1 register because of n3 > m Transfer n2 Transfer at underflow of TRD1 register because of first setting to n2 < m n1 Transfer with timing set by bits CMD1 to CMD0 TRDIOB0 output TRDIOD0 output m: Value set in TRDGRA0 register The above applies under the following conditions: * Bits CMD1 to CMD0 in the TRDFCR register are set to 11b (data in the buffer register is transferred at compare match between registers TRD0 and TRDGRA0 in complementary PWM mode). * Both the OSL0 and OLS1 bits in the TRDFCR register are set to 1 (active `H" for normal-phase and counter-phase). Figure 23.6 Operation when Value in Buffer Register Value in TRDGRA0 Register in Complementary PWM Mode Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 437 of 450 R8C/2K Group, R8C/2L Group 23. Usage Notes When the value in the buffer register is set to 0000h: Transfer takes place at compare match between registers TRD0 and TRDGRA0. After this, when the buffer register is set to 0001h or above and a smaller value than the value of the TRDGRA0 register, and a compare match occurs between registers TRD0 and TRDGRA0 for the first time after setting, the value is transferred to the general register. After that, the value is transferred with the timing selected by bits CMD1 to CMD0. m+1 Count value in TRD0 register n2 n1 Count value in TRD1 register 0000h TRDGRD0 register 0000h n1 Transfer Transfer TRDGRB0 register n2 n1 n1 Transfer with timing set by bits CMD1 to CMD0 Transfer 0000h Transfer at compare match between registers TRD0 and TRDGRA0 because content in TRDGRD0 register is set to 0000h. Transfer n1 Transfer at compare match between registers TRD0 and TRDGRA0 because of first setting to 0001h n1 < m Transfer with timing set by bits CMD1 to CMD0 TRDIOB0 output TRDIOD0 output m: Value set in TRDGRA0 register The above applies under the following conditions: * Bits CMD1 to CMD0 in the TRDFCR register are set to 10b (data in the buffer register is transferred at underflow of the TRD1 register in PWM mode). * Both the OLS0 and OLS1 bits in the TRDFCR register are set to 1 (active "H" for normal-phase and counter-phase). Figure 23.7 23.3.4.8 Operation when Value in Buffer Register Is Set to 0000h in Complementary PWM Mode Count Source fOCO40M * The count source fOCO40M can be used with supply voltage VCC = 3.0 to 5.5 V. For supply voltage other than that, do not set bits TCK2 to TCK0 in registers TRDCR0 and TRDCR to 110b (select fOCO40M as the count source). Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 438 of 450 R8C/2K Group, R8C/2L Group 23.4 23. Usage Notes Notes on Serial Interface * When reading data from the UiRB (i = 0 or 2) register either in the clock synchronous serial I/O mode or in the clock asynchronous serial I/O mode. Ensure the data is read in 16-bit units. When the high-order byte of the UiRB register is read, bits PER and FER in the UiRB register and the RI bit in the UiC1 register are set to 0. To check receive errors, read the UiRB register and then use the read data. Example (when reading receive buffer register): MOV.W 00A6H,R0 ; Read the U0RB register * When writing data to the UiTB register in the clock asynchronous serial I/O mode with 9-bit transfer data length, write data to the high-order byte first then the low-order byte, in 8-bit units. Example (when reading transmit buffer register): MOV.B #XXH,00A3H ; Write the high-order byte of U0TB register MOV.B #XXH,00A2H ; Write the low-order byte of U0TB register Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 439 of 450 R8C/2K Group, R8C/2L Group 23.5 23. Usage Notes Notes on Hardware LIN For the time-out processing of the header and response fields, use another timer to measure the duration of time with a Synch Break detection interrupt as the starting point. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 440 of 450 R8C/2K Group, R8C/2L Group 23.6 23. Usage Notes Notes on A/D Converter * Write to each bit (other than bit 6) in the ADCON0 register, each bit in the ADCON1 register, or the SMP bit in the ADCON2 register when A/D conversion is stopped (before a trigger occurs). When the VCUT bit in the ADCON1 register is changed from 0 (VREF not connected) to 1 (VREF connected), wait for at least 1 s before starting the A/D conversion. * After changing the A/D operating mode, select an analog input pin again. * When using the one-shot mode, ensure that A/D conversion is completed before reading the AD register. The IR bit in the ADIC register or the ADST bit in the ADCON0 register can be used to determine whether A/D conversion is completed. * When using the repeat mode, select the frequency of the A/D converter operating clock AD or more for the CPU clock during A/D conversion. * If the ADST bit in the ADCON0 register is set to 0 (A/D conversion stops) by a program and A/D conversion is forcibly terminated during an A/D conversion operation, the conversion result of the A/D converter will be undefined. If the ADST bit is set to 0 by a program, do not use the value of the AD register. * Connect 0.1 F capacitor between the P4_2/VREF pin and AVSS pin. * Do not enter stop mode during A/D conversion. * Do not enter wait mode when the CM02 bit in the CM0 register is set to 1 (peripheral function clock stops in wait mode) during A/D conversion. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 441 of 450 R8C/2K Group, R8C/2L Group 23.7 23. Usage Notes Notes on Flash Memory 23.7.1 CPU Rewrite Mode 23.7.1.1 Operating Speed Before entering CPU rewrite mode (EW0 mode), select 5 MHz or below for the CPU clock using the CM06 bit in the CM0 register and bits CM16 to CM17 in the CM1 register. This does not apply to EW1 mode. 23.7.1.2 Prohibited Instructions The following instructions cannot be used in EW0 mode because they reference data in the flash memory: UND, INTO, and BRK. 23.7.1.3 Non-Maskable Interrupts * EW0 Mode Once a watchdog timer, oscillation stop detection, voltage monitor1, or voltage monitor 2 interrupt request is acknowledged, auto-erasure or auto-programming is forcibly stopped immediately and the flash memory is reset. Interrupt handling starts after a fixed period and the flash memory restarts. As the block during auto-erasure or the address during auto-programming is forcibly stopped, the normal value may not be readable. Execute auto-erasure again and ensure it completes normally. The watchdog timer does not stop during command operation, so that interrupt requests may be generated. Initialize the watchdog timer regularly. Do not use the address match interrupt while a command is being executed because the vector of the address match interrupt is allocated in ROM. Do not use a non-maskable interrupt while block 0 is being automatically erased because the fixed vector is allocated in block 0. * EW1 Mode Once a watchdog timer, oscillation stop detection, voltage monitor1, or voltage monitor 2 interrupt request is acknowledged, auto-erasure or auto-programming is forcibly stopped immediately and the flash memory is reset. Interrupt handling starts after a fixed period and the flash memory restarts. As the block during auto-erasure or the address during auto-programming is forcibly stopped, the normal value may not be readable. Execute auto-erasure again and ensure it completes normally. The watchdog timer does not stop even during command operation, so that interrupt requests may be generated. Initialize the watchdog timer by using the erase-suspend function. Do not use the address match interrupt while a command is being executed because the vector of the address match interrupt is allocated in ROM. Do not use a non-maskable interrupt while block 0 is being automatically erased because the fixed vector is allocated in block 0. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 442 of 450 R8C/2K Group, R8C/2L Group 23.7.1.4 23. Usage Notes How to Access Write 0 before writing 1 when setting Bits FMR01, FMR02 in the FMR0 register, or FMR11 bit in the FMR1 register to 1. Do not generate an interrupt between writing 0 and 1. 23.7.1.5 Rewriting User ROM Area In EW0 Mode, if the supply voltage drops while rewriting any block in which a rewrite control program is stored, it may not be possible to rewrite the flash memory because the rewrite control program cannot be rewritten correctly. In this case, use standard serial I/O mode. 23.7.1.6 Program Do not write additions to the already programmed address. 23.7.1.7 Suspend Do not use the block erase command during program-suspend. 23.7.1.8 Entering Stop Mode or Wait Mode Do not enter stop mode or wait mode during erase-suspend. 23.7.1.9 Program and Erase Voltage for Flash Memory To perform programming and erasure, use VCC = 2.7 V to 5.5 V as the supply voltage. Do not perform programming and erasure at less than 2.7 V. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 443 of 450 R8C/2K Group, R8C/2L Group 23.8 23. Usage Notes Notes on Noise 23.8.1 Inserting a Bypass Capacitor between VCC and VSS Pins as a Countermeasure against Noise and Latch-up Connect a bypass capacitor (at least 0.1 F) using the shortest and thickest write possible. 23.8.2 Countermeasures against Noise Error of Port Control Registers During rigorous noise testing or the like, external noise (mainly power supply system noise) can exceed the capacity of the MCU's internal noise control circuitry. In such cases the contents of the port related registers may be changed. As a firmware countermeasure, it is recommended that the port registers, port direction registers, and pull-up control registers be reset periodically. However, examine the control processing fully before introducing the reset routine as conflicts may be created between the reset routine and interrupt routines. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 444 of 450 R8C/2K Group, R8C/2L Group 24. Notes for On-Chip Debugger 24. Notes for On-Chip Debugger When using the on-chip debugger to develop and debug programs for the R8C/2K Group and R8C/2L Group take note of the following. (1) (2) (3) (4) Some of the user flash memory and RAM areas are used by the on-ship debugger. These areas cannot be accessed by the user. Refer to the on-chip debugger manual for which areas are used. Do not set the address match interrupt (registers AIER, RMAD0, and RMAD1 and fixed vector tables) in a user system. Do not use the BRK instruction in a user system. Debugging is available under the condition of supply voltage VCC = 2.7 to 5.5 V. Debugging with the on-chip debugger under less than 2.7 V is not allowed. Connecting and using the on-chip debugger has some special restrictions. Refer to the on-chip debugger manual for details. Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 445 of 450 R8C/2K Group, R8C/2L Group Appendix 1. Package Dimensions Appendix 1. Package Dimensions Diagrams showing the latest package dimensions and mounting information are available in the "Packages" section of the Renesas Technology website. JEITA Package Code P-LQFP32-7x7-0.80 RENESAS Code PLQP0032GB-A Previous Code 32P6U-A MASS[Typ.] 0.2g HD *1 D 24 17 NOTE) 1. DIMENSIONS "*1" AND "*2" DO NOT INCLUDE MOLD FLASH. 2. DIMENSION "*3" DOES NOT INCLUDE TRIM OFFSET. 16 25 bp c c1 HE *2 E b1 Reference Dimension in Millimeters Symbol 32 9 1 ZE Terminal cross section 8 ZD c L A A1 F A2 Index mark L1 y e Rev.1.10 Dec 21, 2007 REJ09B0406-0110 *3 Detail F bp x Page 446 of 450 D E A2 HD HE A A1 bp b1 c c1 e x y ZD ZE L L1 Min Nom Max 6.9 7.0 7.1 6.9 7.0 7.1 1.4 8.8 9.0 9.2 8.8 9.0 9.2 1.7 0.1 0.2 0 0.32 0.37 0.42 0.35 0.09 0.145 0.20 0.125 0 8 0.8 0.20 0.10 0.7 0.7 0.3 0.5 0.7 1.0 R8C/2K Group, R8C/2L Group Appendix 2. Connection Examples between Serial Writer and On-Chip Debugging Appendix 2. Connection Examples between Serial Writer and On-Chip Debugging Emulator Appendix Figure 2.1 shows a Connection Example with M16C Flash Starter (M3A-0806) and Appendix Figure 2.2 shows a Connection Example with E8 Emulator (R0E000080KCE00). VCC 25 27 VSS Connect oscillation circuit(1) 26 24 2 23 R8C/2K Group, R8C/2L Group RESET 28 1 (2) TXD 29 30 32 31 MODE 3 4 5 6 7 22 21 20 19 18 17 8 16 15 14 13 12 11 9 10 10 TXD 7 VSS RXD 4 1 VCC M16C Flash Starter (M3A-0806) (2) RXD NOTES: 1. An oscillation circuit must be connected, even when operating with the on-chip oscillator clock. 2. For development tools only. Appendix Figure 2.1 Connection Example with M16C Flash Starter (M3A-0806) VCC Open collector buffer 12 RESET 23 3 4 5 22 21 20 19 18 17 8 15 16 14 13 11 12 9 10 8 VCC 7 MODE 10 25 13 26 14 27 24 2 6 4.7k 10% 28 1 R8C/2K Group, R8C/2L Group VSS 30 Connect oscillation circuit(1) 29 32 4.7k or more 31 User logic 7 MODE 6 4 2 VSS E8 emulator (R0E000080KCE00) Appendix Figure 2.2 Rev.1.10 Dec 21, 2007 REJ09B0406-0110 NOTE: 1. It is not necessary to connect an oscillation circuit when operating with the on-chip oscillator clock. Connection Example with E8 Emulator (R0E000080KCE00) Page 447 of 450 R8C/2K Group, R8C/2L Group Appendix 3. Example of Oscillation Evaluation Circuit Appendix 3. Example of Oscillation Evaluation Circuit Appendix Figure 3.1 shows an Example of Oscillation Evaluation Circuit. VCC 25 26 27 28 24 2 23 R8C/2K Group, R8C/2L Group 3 4 VSS 29 30 Connect oscillation circuit 31 32 RESET 1 5 6 7 22 21 20 19 18 8 17 Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Example of Oscillation Evaluation Circuit Page 448 of 450 16 Appendix Figure 3.1 15 14 13 12 11 10 9 NOTE: 1. After reset, the XIN clock stops. Write a program to oscillate the XIN clock. R8C/2K Group, R8C/2L Group Index Index [A] AD ....................................................................................... 351 ADCON0 ............................................................................. 350 ADCON1 ............................................................................. 351 ADCON2 ............................................................................. 351 ADIC .................................................................................... 102 AIER .................................................................................... 117 [C] CM0 ....................................................................................... 74 CM1 ....................................................................................... 75 CSPR .................................................................................. 131 [F] FMR0 .................................................................................. 367 FMR1 .................................................................................. 370 FMR4 .................................................................................. 371 FRA0 ..................................................................................... 77 FRA1 ..................................................................................... 77 FRA2 ..................................................................................... 78 FRA6 ..................................................................................... 78 FRA7 ..................................................................................... 78 [I] INT0IC ................................................................................. 104 INT1IC ................................................................................. 104 INT3IC ................................................................................. 104 INTEN ................................................................................. 111 INTF .................................................................................... 112 [K] KIEN .................................................................................... 115 KUPIC ................................................................................. 102 [L] LINCR ................................................................................. 335 LINCR2 ............................................................................... 335 LINST .................................................................................. 336 [O] OCD ...................................................................................... 76 OFS ............................................................... 26, 126, 131, 365 [P] P2DRR .................................................................................. 55 PDi (i = 0 to 4) ....................................................................... 54 Pi (i = 0 to 4) .......................................................................... 55 PINSR1 ......................................................................... 56, 321 PINSR2 ......................................................................... 56, 153 PINSR3 ......................................................................... 56, 177 PM0 ....................................................................................... 69 PM1 ....................................................................................... 69 PMR .............................................................................. 56, 111 PRCR .................................................................................... 96 PUR0 ..................................................................................... 57 PUR1 ..................................................................................... 57 [R] RMAD0 ................................................................................ 117 RMAD1 ................................................................................ 117 Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 449 of 450 [S] S0RIC S0TIC S2RIC S2TIC .................................................................................. 102 .................................................................................. 102 .................................................................................. 102 .................................................................................. 102 [T] TRA ..................................................................................... 138 TRACR ................................................................................ 137 TRAIC .................................................................................. 102 TRAIOC ....................................... 137, 139, 142, 144, 146, 149 TRAMR ................................................................................ 138 TRAPRE .............................................................................. 138 TRBCR ................................................................................ 154 TRBIC .................................................................................. 102 TRBIOC ............................................... 155, 157, 161, 164, 168 TRBMR ................................................................................ 155 TRBOCR ............................................................................. 154 TRBPR ................................................................................ 156 TRBPRE .............................................................................. 156 TRBSC ................................................................................ 156 TRC ..................................................................................... 181 TRCCR1 ...................................................... 178, 201, 205, 210 TRCCR2 .............................................................................. 182 TRCDF ................................................................................ 183 TRCGRA ............................................................................. 181 TRCGRB ............................................................................. 181 TRCGRC ............................................................................. 181 TRCGRD ............................................................................. 181 TRCIC .................................................................................. 103 TRCIER ............................................................................... 179 TRCIOR0 ............................................................. 185, 194, 199 TRCIOR1 ............................................................. 185, 195, 200 TRCMR ................................................................................ 177 TRCOER ............................................................................. 184 TRCSR ................................................................................ 180 TRD0 ........................................... 237, 253, 267, 278, 290, 304 TRD0IC ................................................................................ 103 TRD1 ........................................................... 237, 253, 267, 290 TRD1IC ................................................................................ 103 TRDCR0 ...................................... 233, 248, 264, 276, 287, 302 TRDCR1 ...................................................... 233, 248, 264, 287 TRDDF0 .............................................................................. 232 TRDDF1 .............................................................................. 232 TRDFCR ...................................... 231, 245, 262, 274, 285, 299 TRDGRAi (i = 0 to 1) ................... 238, 253, 268, 279, 290, 305 TRDGRBi (i = 0 to 1) ................... 238, 253, 268, 279, 290, 305 TRDGRCi (i = 0 to 1) ................... 238, 253, 268, 279, 290, 305 TRDGRDi (i = 0 to 1) ................... 238, 253, 268, 279, 290, 305 TRDIER0 ..................................... 237, 252, 266, 278, 289, 304 TRDIER1 ..................................... 237, 252, 266, 278, 289, 304 TRDIORA0 .................................................................. 234, 249 TRDIORA1 .................................................................. 234, 249 TRDIORC0 .................................................................. 235, 250 TRDIORC1 .................................................................. 235, 250 TRDMR ........................................ 229, 243, 260, 273, 284, 298 TRDOCR ............................................................. 247, 264, 301 TRDOER1 ........................................... 246, 263, 275, 286, 300 TRDOER2 ........................................... 246, 263, 275, 286, 300 TRDPMR ............................................................. 230, 244, 261 TRDPOCR0 ......................................................................... 267 TRDPOCR1 ......................................................................... 267 TRDSR0 ...................................... 236, 251, 265, 277, 288, 303 TRDSR1 ...................................... 236, 251, 265, 277, 288, 303 TRDSTR ...................................... 229, 243, 260, 273, 283, 297 R8C/2K Group, R8C/2L Group [U] U0BRG ................................................................................ 318 U0C0 ................................................................................... 319 U0C1 ................................................................................... 320 U0MR .................................................................................. 318 U0RB ................................................................................... 320 U0TB ................................................................................... 319 U2BRG ................................................................................ 318 U2C0 ................................................................................... 319 U2C1 ................................................................................... 320 U2MR .................................................................................. 318 U2RB ................................................................................... 320 U2TB ................................................................................... 319 [V] VCA1 ..................................................................................... 35 VCA2 ............................................................................... 35, 79 VW0C .................................................................................... 36 VW1C .................................................................................... 37 VW2C .................................................................................... 38 [W] WDC .................................................................................... 130 WDTR ................................................................................. 130 WDTS .................................................................................. 130 Rev.1.10 Dec 21, 2007 REJ09B0406-0110 Page 450 of 450 Index REVISION HISTORY REVISION HISTORY R8C/2K Group, R8C/2L Group Hardware Manual R8C/2K Group, R8C/2L Group Hardware Manual Description Rev. Date 0.10 Jul 20, 2007 - 0.20 Aug 31, 2007 108 Figure 12.11 "UART1 receive", "UART1 transmit" deleted 199 Figure 16.50 "* The CCLR bit in the TRCCR1 register is set to 0 .... compare match)." "* The CCLR bit in the TRCCR1 register is set to 1 .... compare match)." 200 Table 16.20 "j = A, B, C, or D" " j = B, C, or D" 254 Figure 16.96 revised 338 Figure 18.9 "When the SBE bit .... timer RA may be used in timer mode after the SBDCT flag in the LINST register is set to 1." "When the SBE bit .... timer RA can be used in timer mode after the SBDCT flag in the LINST register is set to 1 and the RXDSF flag is set to 0." 355 Figure 19.10 "SW5 conducts when compare operation is in progress." added 442 Appendix Figure 2.1 revised 1.00 Nov 7, 2007 Page Summary First Edition issued All pages "Preliminary" deleted 3, 5 Table 1.2, Table 1.4; Current consumption: "TBD" "Typ. 10 mA" "Typ. 6 mA" "Typ. 2.0 A" "Typ. 0.7 A" revised 6, 7 Table 1.5, Table 1.6 revised Figure 1.1, Figure 1.2; ROM number "XXX" added, NOTE1 added 20 Table 4.4 "005Fh" "006Fh" "007Fh" "008Fh" added 45, 56 Figure 7.11 added 58 to 60 Table 7.5 NOTE3 added Table 7.6, Table 7.7, Table 7.10, Table 7.12, Table 7.14 NOTE2 added 65 Table 7.28 NOTE2 and NOTE3 added Table 7.29, Table 7.31 NOTE2 added 111 Figure 12.12 added 136 Figure 16.1 "TSTART" "TCSTF" revised 153 Figure 16.13 added 176 Table 16.13 "00F7h" added 177 Figure 16.28 added 307 Figure 16.145 "TSTP0" "CSEL0" revised 321 Figure 17.6 added 402 Table 22.2 NOTE2 revised 410, 411 Table 22.14, Table 22.15 revised 415, 419 Table 22.21, Table 22.27 revised 447 Appendix Figure 3.1 revised C-1 REVISION HISTORY Rev. Date 1.10 Dec 21, 2007 R8C/2K Group, R8C/2L Group Hardware Manual Description Page Summary 3, 5 Table 1.2, Table 1.4: revised, NOTE2 added 6, 7 Figure 1.1, Figure 1.2: "Y: Operating ambient ....", NOTE1 added 15, 16 Figure 3.1, Figure 3.2: "Expanded area" deleted 17 Table 4.1 "002Ch" added, "003Bh" "003Ch" "003Dh" deleted 20 Table 4.4 "00D4h" "00D6h" revised 22 Table 4.6 "0143h" revised 35 Figure 6.5 "VCA Register" NOTE7 deleted 59 Table 7.11 revised 73 Figure 10.2 revised 78 Figure 10.7 "FRA7 Register" added 79 Figure 10.8 NOTE7 deleted 82 10.2.2 revised 83 10.3.8 revised 185 Figure 16.38 TRCIOR0: b3 revised, NOTE4 added 192 16.3.4, Table 16.16: revised 193 Figure 16.44 revised 194 Figure 14.45 b3 revised, NOTE3 added 199 Figure 14.49 b3 revised 203 Table 16.20 Interrupt request generation timing: Specification "... and TRCGRj match)" "... and TRCGRh match)" "h = A, B, C, or D" added 209 Table 16.22 " j = A, B, C, or D" " j = A, B, or C" 297 Figure 16.135 b1 revised 331 Table 17.7 revised 402 22. "The electrical characteristics ...." added 408 Table 21.10 Symbol "fOCO40M": Parameter added, NOTE4 added C-2 R8C/2K Group, R8C/2L Group Hardware Manual Publication Date: Published by: Rev.0.10 Rev.1.10 Jul 20, 2007 Dec 21, 2007 Sales Strategic Planning Div. Renesas Technology Corp. (c) 2007. Renesas Technology Corp., All rights reserved. Printed in Japan R8C/2K Group, R8C/2L Group Hardware Manual 1753, Shimonumabe, Nakahara-ku, Kawasaki-shi, Kanagawa 211-8668 Japan REJ09B0406-0110