High Common-Mode Voltage,
Bidirectional Current Shunt Amplifier
Data Sheet
AD8206
FEATURES
Ideal for current shunt applications
High common-mode voltage range
−2 V to +65 V operating
−25 V to +75 V survival
Gain = 20
Wide operating temperature range
40°C to +125°C for Y grade and WY grade
40°C to +150°C for WH grade
Bidirectional operation
Available in 8-lead SOIC
Qualified for automotive applications
EXCELLENT AC AND DC PERFORMANCE
15 µV/°C offset drift
30 ppm/°C gain drift
80 dB CMRR dc to 20 kHz
APPLICATIONS
High-side current sensing in
Motor controls
Transmission controls
Diesel-injection controls
Engine management
Suspension controls
Vehicle dynamic controls
DC-to-dc converters
FUNCTIONAL BLOCK DIAGRAM
04953-001
AD8206
8
1
4
2
3
7
5
6
+IN
–IN
NC
NC = NO CONNECT GND
V+
OUT
V
REF
1
V
REF
2
Figure 1.
GENERAL DESCRIPTION
The AD8206 is a single-supply difference amplifier for amplifying
small differential voltages in the presence of large common-mode
voltages. The operating input common-mode voltage range extends
from −2 V to +65 V. The typical single-supply voltage is 5 V.
The AD8206 is offered in an 8-lead SOIC package. The Y grade
and WY grade models are rated for operation from −40°C to
+125°C. The WH grade is rated from −40°C to +150°C.
Excellent DC performance over temperature keeps errors in the
measurement loop to a minimum. Offset drift is typically less
than 15 µV/°C, and gain drift is typically below 30 ppm/°C.
The output offset can be adjusted from 0.08 V to 4.7 V with a
5 V supply by using the VREF1 and VREF2 pins. With VREF1
attached to the V+ pin, and VREF2 attached to the GND pin, the
output is set at half scale. Attaching both pins to GND causes
the output to be unipolar, starting near ground. Attaching both
pins to V+ causes the output to be unipolar starting near V+.
Other offsets can be obtained by applying an external voltage to
the VREF1 and VREF2 pins.
Rev. C Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©20052014 Analog Devices, Inc. All rights reserved.
Technical Support www.analog.com
AD8206 Data Sheet
Rev. C | Page 2 of 13
TABLE OF CONTENTS
Features .............................................................................................. 1
Excellent AC and DC Performance ................................................ 1
Applications ....................................................................................... 1
Functional Block Diagram .............................................................. 1
General Description ......................................................................... 1
Revision History ............................................................................... 2
Specifications ..................................................................................... 3
Absolute Maximum Ratings ............................................................ 5
ESD Caution .................................................................................. 5
Pin Configuration and Function Descriptions ............................. 6
Typical Performance Characteristics ............................................. 7
Theory of Operation ........................................................................ 9
Output Offset Adjustment ............................................................. 10
Unidirectional Operation .......................................................... 10
Ground Referenced Output ...................................................... 10
V+ Referenced Output .............................................................. 10
Bidirectional Operation ............................................................. 10
External Referenced Output ..................................................... 11
Splitting the Supply .................................................................... 11
Splitting an External Reference ................................................ 11
Applications Information .............................................................. 12
High-Side Current Sense with a Low-Side Switch ................. 12
High-Side Current Sense with a High-Side Switch ............... 12
Outline Dimensions ....................................................................... 13
Ordering Guide .......................................................................... 13
Automotive Products ................................................................. 13
REVISION HISTORY
11/14—Rev. B to Rev. C
Changes to Pin Configuration and Function Descriptions
Section ................................................................................................ 6
Changed Applications Section to Applications Information
Section .............................................................................................. 12
11/12—Rev. A to Rev. B
Added WH Grade Models ................................................. Universal
Change to Product Title, Features Section, and General
Description Section .......................................................................... 1
Changes to Table 1 ............................................................................ 3
Added Y Grade and WY Grade Parameter, Table 2 and WH
Grade Parameter, Table 2 ................................................................. 5
Changes to Theory of Operation Section ...................................... 9
Updated Outline Dimensions ....................................................... 13
Changes to Ordering Guide .......................................................... 13
5/10—Rev. 0 to Rev. A
Removed Die Form ............................................................ Universal
Changes to Features, General Description Sections ..................... 1
Changes to Output Resistance ......................................................... 3
Changes to Table 2 ............................................................................. 4
Changes to Theory of Operation Section....................................... 8
Changes to Ordering Guide .......................................................... 12
Added Automotive Products Section .......................................... 12
7/05—Revision 0: Initial Version
Data Sheet AD8206
SPECIFICATIONS
TA = operating temperature range, VS = 5 V, unless otherwise noted.
Table 1.
Parameter Test Conditions/Comments
AD8206 SOIC
Unit Min Typ Max
GAIN
Initial 20 V/V
Accuracy VO ≥ 0.1 V dc, 25°C ±1 %
Accuracy Over Temperature Specified temperature range ±1.2 %
Gain vs. Temperature 30 ppm/°C
VOLTAGE OFFSET
Offset Voltage (RTI) 25°C ±2 mV
Over Temperature (RTI) Specified temperature range ±4.5 mV
Offset Drift 15 µV/°C
INPUT
Input Impedance
Differential 400 kΩ
Common Mode 200 kΩ
Input Voltage Range
Common mode, continuous
−2
+65
V
Differential1 250 mV
Common-Mode Rejection 25°C, f = dc to 20 kHz2 76 86 dB
Operating temperature range,
f = dc to 20 kHz2
76 80 dB
OUTPUT
Output Voltage Range AD8206YRZ, RL = 25 kΩ 0.08 4.7 V
AD8206WYRZ, RL = 25 kΩ 0.08 4.7 V
AD8206WHRZ, RL = 25 kΩ 0.08 4.65 V
Output Resistance 2
DYNAMIC RESPONSE
Small Signal −3 dB Bandwidth
100
kHz
Slew Rate 0.5 V/µs
NOISE
0.1 Hz to 10 Hz, RTI
20
µV p-p
Spectral Density, 1 kHz, RTI 0.5 µV/√Hz
OFFSET ADJUSTMENT
Ratiometric Accuracy3 Divider to supplies 0.497 0.503 V/V
Accuracy, RTO Voltage applied to VREF1 and VREF2 in parallel ±2 mV/V
Output Offset Adjustment Range AD8206YRZ, VS = 5 V 0.08 4.7 V
AD8206WYRZ, VS = 5 V 0.08 4.7 V
AD8206WHRZ, VS = 5 V 0.08 4.65 V
VREF Input Voltage Range
0.0
V
S
V
VREF Divider Resistor Values 24 32 40 kΩ
Rev. C | Page 3 of 13
AD8206 Data Sheet
Parameter Test Conditions/Comments
AD8206 SOIC
Unit Min Typ Max
POWER SUPPLY
Operating Range 4.5 5.5 V
Quiescent Current Over Temperature AD8206YRZ, VO = 0.1 V dc 2 mA
AD8206WYRZ, VO = 0.1 V dc 2 mA
AD8206WHRZ, VO = 0.1 V dc 2.2 mA
Power Supply Rejection Ratio 70 dB
OPERATING TEMPERATURE RANGE
For Specified Performance AD8206YRZ −40 +125 °C
AD8206WYRZ
−40
+125
°C
AD8206WHRZ −40 +150 °C
1 Input voltage range = ±125 mV with half-scale offset.
2 Source imbalance < 2 Ω.
3 The offset adjustment is ratiometric to the power supply when VREF1 and VREF2 are used as a divider between the supplies.
Rev. C | Page 4 of 13
Data Sheet AD8206
ABSOLUTE MAXIMUM RATINGS
Table 2.
Parameter Rating
Supply Voltage 12.5 V
Continuous Input Voltage −25 V to +75 V
Input Transient Survival −30 V to +80 V
Differential Input Survival −25 V to +75 V
Reverse Supply Voltage 0.3 V
Operating Temperature Range
Y Grade and WY Grade −40°C to +125°C
−40°C to +150°C
Storage Temperature Range −65°C to +150°C
Output Short-Circuit Duration Indefinite
Stresses at or above those listed under Absolute Maximum
Ratings may cause permanent damage to the product. This is a
stress rating only; functional operation of the product at these
or any other conditions above those indicated in the operational
section of this specification is not implied. Operation beyond
the maximum operating conditions for extended periods may
affect product reliability.
ESD CAUTION
Rev. C | Page 5 of 13
AD8206 Data Sheet
Rev. C | Page 6 of 13
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
04953-002
Figure 2. Metallization Diagram
NC = NO CONNECT
AD8206
TOP VIEW
(Not to Scale)
–IN
1
GND
2
V
REF
2
3
NC
4
+IN
V
REF
1
V+
OUT
8
7
6
5
04953-003
Figure 3. Pin Configuration
Table 3. Pin Function Descriptions
Pin No. Mnemonic X Y
1 −IN −209 +486
2 GND −447 +34
3 VREF2 −432 −480
4 NC N/A N/A
5 OUT +444 −495
6 V+ +444 −227
7 VREF1 +456 +342
8 +IN +207 +486
Die size is 1245 μm by 1400 μm.
Die thickness is 13 mil.
Minimum passivation opening (minimum bond pad size)
is 92 μm × 92 μm.
Passivation type is 8KA USG (Oxide) + 10KA Oxynitride.
Bond pad metal composition is 99.5% Al and 0.5% Cu.
Backside potential is V+.
Data Sheet AD8206
Rev. C | Page 7 of 13
TYPICAL PERFORMANCE CHARACTERISTICS
500
–500
–400
–300
–200
–100
0
100
200
300
400
–40 –20 0 20 40 60 80 100 120 140
04953-036
TEMPERATURE (C)
V
OSI
(V)
TYPICAL
IN SOIC
TYPICAL
DIE
Figure 4. Typical Offset Drift
120
110
100
90
80
70
60
50
40
30
20
10
010 100 1k 10k 100k 1M 10M
04953-004
FREQUENCY (Hz)
CMR (dB)
Figure 5. CMR vs. Frequency
12000
–12000
–10000
–8000
–6000
–4000
–2000
0
2000
4000
6000
8000
10000
–40 –20 0 20 40 60 80 100 120 140
04953-035
TEMPERATURE (C)
GAIN ERROR (ppm)
TYPICAL
IN SOIC
TYPICAL
DIE
Figure 6. Gain Drift
40
35
30
25
20
15
10
5
010 100 1k 10k 100k 1M
04953-007
FREQUENCY (Hz)
GAIN (dB)
Figure 7. Typical Small Signal Bandwidth (VOUT = 200 mV p-p)
04953-023
40s/DIV
200mV/DIV
1V/DIV
Figure 8. Rise/Fall Time
04953-025
2s/DIV
250mV/DIV
2V/DIV
Figure 9. Differential Overload Recovery (Falling)
AD8206 Data Sheet
Rev. C | Page 8 of 13
04953-024
2s/DIV
250mV/DIV
2V/DIV
Figure 10. Differential Overload Recovery (Rising)
04953-022
40s/DIV
2V/DIV
0.01%/DIV
Figure 11. Settling Time
04953-026
1s/DIV
50V/DIV
50mV/DIV
Figure 12. Common-Mode Response
0.50
0.45
0.40
0.35
0.30
0.25
0.20
0.15
0.10
0.05
0
–40 –20 0 20 40 60 80 100 120 140
04953-030
TEMPERATURE (C)
MAXIMUM OUTPUT SINK CURRENT (mA)
Figure 13. Output Sink Current vs. Temperature
10
9
8
7
6
5
4
3
2
1
0
–40 –20 0 20 40 60 80 100 120 140
04953-031
TEMPERATURE (C)
MAXIMUM OUTPUT SOURCE CURRENT (mA)
Figure 14. Output Source Current vs. Temperature
5.0
4.9
4.8
4.7
4.6
4.5
4.4
4.3
4.2
4.1
4.0
3.9
3.8
3.7
3.6
3.5 0 4.03.53.02.52.01.51.00.5
04953-034
OUTPUT SOURCE CURRENT (mA)
OUTPUT VOLTAGE RANGE (V p-p)
Figure 15. Output Voltage Range vs. Output Source Current
Data Sheet AD8206
THEORY OF OPERATION
The AD8206 is a single-supply difference amplifier that uses a
unique architecture to accurately amplify small differential current
shunt voltages in the presence of rapidly changing common-mode
voltage. It is offered in an 8-lead SOIC package.
In typical applications, the AD8206 is used to measure current
by amplifying the voltage across a current shunt placed across
the inputs.
The gain of the AD8206 is 20 V/V, with an accuracy of 1.2%.
This accuracy is guaranteed over the operating temperature range
of −40°C to +125°C. Note, however, that the WH grade version
of the AD8206 is specified for operation from −40°C to +150°C,
with the same accuracy of 1.2%.
The AD8206 operates with a single supply from 4.5 V to 10 V
(absolute maximum = 12.5 V). The supply current is less than
2 mA.
High accuracy trimming of the internal resistors allows the
AD8206 to have a typical common-mode rejection ratio better
than 80 dB from dc to 20 kHz. The minimum common-mode
rejection ratio over the operating temperature is 76 dB.
The output offset can be adjusted from 0.08 V to 4.7 V
(VS = 5 V) for unidirectional and bidirectional operation.
The AD8206 consists of two amplifiers (A1 and A2), a resistor
network, a small voltage reference, and a bias circuit. See Figure 16
for a simplified schematic diagram (bias circuit not shown).
The set of input attenuators preceding A1 consist of RA, RB, and
RC, which reduce the common-mode voltage to match the input
voltage range of A1. The two attenuators form a balanced bridge
network. When the bridge is balanced, the differential voltage
created by a common-mode voltage is 0 V at the inputs of A1.
The input attenuation ratio is 1/16.7. The combined series
resistance of RA, RB, and RC is approximately 200 kΩ ± 20%.
By attenuating the voltages at Pin 1 and Pin 8, the A1 amplifier
inputs are held within the power supply range, even if Pin 1 and
Pin 8 exceed the supply or fall below common (ground). A
reference voltage of 250 mV biases the attenuator above ground.
This allows the amplifier to operate in the presence of negative
common-mode voltages.
The input network also attenuates normal (differential) mode
voltages. A1 amplifies the attenuated signal by 26. The input
and output of this amplifier are differential to maximize the
ac common-mode rejection.
A2 converts the differential voltage from A1 into a single-ended
signal and provides further amplification. The gain of this
second stage is 12.86.
The reference inputs, VREF1 and VREF2, are tied through resistors
to the positive input of A2, which allows the output offset to be
adjusted anywhere in the output operating range. The gain is
1 V/V from the reference pins to the output when the reference
pins are used in parallel. The gain is 0.5 V/V when they are used
to divide the supply.
The ratios of Resistors RA, RB, RC, RD, and RF are trimmed to a
high level of precision to allow the common-mode rejection
ratio to exceed 80 dB. This is accomplished by laser trimming
the resistor ratio matching to better than 0.01%.
The total gain of 20 is made up of the input attenuation of
1/16.7 multiplied by the first stage gain of 26 and the second
stage gain of 12.86.
The output stage is a Class A with a PNP pull-up transistor and
a 300 µA current sink pull-down.
04953-013
AD8206
+IN–IN
250mV
GND
A1
A2
R
A
R
A
R
B
R
B
R
F
R
F
R
D
R
D
R
E
R
F
R
C
R
C
V
OUT
R
REF
R
REF
V
REF
1
V
REF
2
Figure 16. Simplified Schematic
Rev. C | Page 9 of 13
AD8206 Data Sheet
OUTPUT OFFSET ADJUSTMENT
The output of the AD8206 can be adjusted for unidirectional or
bidirectional operation.
UNIDIRECTIONAL OPERATION
Unidirectional operation allows the AD8206 to measure
currents through a resistive shunt in one direction. The basic
modes for unidirectional operation are ground referenced
output mode and V+ referenced output mode.
For unidirectional operation, the output can be set at the
negative rail (near ground) or at the positive rail (near V+)
when the differential input is 0 V. The output moves to the
opposite rail when a correct polarity differential input voltage is
applied. In this case, full scale is approximately 250 m V. T h e
required polarity of the differential input depends on the output
voltage setting. If the output is set at the positive rail, the input
polarity needs to be negative to move the output down. If the
output is set at ground, the polarity is positive to move the
output up.
GROUND REFERENCED OUTPUT
When using the AD8206 in this mode, both referenced inputs are
tied to ground, which causes the output to sit at the negative rail
when there are zero differential volts at the input (see Figure 17).
04953-014
AD8206
+IN
IN
NC
NC = NO CONNECT
GND
V+
OUT
VREF1
VREF2
Figure 17. Ground Referenced Output
Table 4. V+ = 5 V
VIN (Referred to −IN) VO
0 V 0.08 V
250 mV 4.7 V
V+ REFERENCED OUTPUT
This mode is set when both reference pins are tied to the
positive supply. It is typically used when the diagnostic scheme
requires detection of the amplifier and the wiring before power
is applied to the load (see Figure 18).
04953-015
AD8206
+IN
IN
NC
NC = NO CONNECT
GND
V+
OUT
V
REF
1
V
REF
2
Figure 18. V+ Referenced Output
Table 5. V+ = 5 V
VIN (Referred to IN) VO
0 V 4.7 V
−250 mV 0.08 V
BIDIRECTIONAL OPERATION
Bidirectional operation allows the AD8206 to measure currents
through a resistive shunt in two directions.
In this case, the output is set anywhere within the output range.
Typically, it is set at half-scale for equal range in both directions.
In some cases, however, it is set at a voltage other than half-scale
when the bidirectional current is nonsymmetrical.
Table 6. V+ = 5 V, VO = 2.5 V with VIN = 0 V
VIN (Referred to −IN) VO
+100 mV
4.5 V
−100 mV 0.5 V
Adjusting the output is accomplished by applying voltage(s) to
the referenced inputs.
VREF1 and VREF2 are tied to internal resistors that connect to an
internal offset node. There is no operational difference between
the pins.
Rev. C | Page 10 of 13
Data Sheet AD8206
EXTERNAL REFERENCED OUTPUT
Tying both pins together and to a reference produces an output
equal to the reference voltage when there is no differential input
(see Figure 19). The output moves down from the reference
voltage when the input is negative, relative to the −IN pin and
up when the input is positive, relative to the −IN pin.
04953-016
AD8206
+IN
–IN
NC
NC = NO CONNECT
GND
V+
OUT
V
REF
1
V
REF
2
2.5V VOLTAGE
REFERENCE
Figure 19. External Referenced Output
SPLITTING THE SUPPLY
By tying one reference pin to V+ and the other to the ground
pin, the output is set at half of the supply when there is no
differential input (see Figure 20). The benefit is that no external
reference is required to offset the output for bidirectional current
measurement. This creates a midscale offset that is ratiometric to
the supply, which means that if the supply increases or decreases,
the output remains at half the supply. For example, if the supply is
5.0 V, the output is at half scale or 2.5 V. If the supply increases by
10% (to 5.5 V), the output goes to 2.75 V.
04953-017
AD8206
+IN
–IN
NC
NC = NO CONNECT
GND
V+
OUT
V
REF
1
V
REF
2
Figure 20. Split Supply
SPLITTING AN EXTERNAL REFERENCE
In this case, an external reference is divided by 2 with an
accuracy of approximately 0.5% by connecting one VREF pin to
ground and the other VREF pin to the reference (see Figure 21).
04953-018
AD8206
+IN
IN
NC
NC = NO CONNECT
GND
V+
OUT
V
REF
1
V
REF
2
5V VOLTAGE
REFERENCE
Figure 21. Split External Reference
Rev. C | Page 11 of 13
AD8206 Data Sheet
APPLICATIONS INFORMATION
A typical application for the AD8206 is high-side measurement
of a current through a solenoid for PWM control of the solenoid
opening. Typical applications include hydraulic transmission
control and diesel injection control.
Two typical circuit configurations are used for this type of
application.
HIGH-SIDE CURRENT SENSE WITH A LOW-SIDE
SWITCH
In this case, the PWM control switch is ground referenced. An
inductive load (solenoid) is tied to a power supply. A resistive
shunt is placed between the switch and the load (see Figure 22).
An advantage of placing the shunt on the high side is that the
entire current, including the recirculation current, can be
measured since the shunt remains in the loop when the switch
is off. In addition, diagnostics can be enhanced because shorts
to ground can be detected with the shunt on the high side.
In this circuit configuration, when the switch is closed, the
common-mode voltage moves down to near the negative rail.
When the switch is opened, the voltage reversal across the
inductive load causes the common-mode voltage to be held
one diode drop above the battery by the clamp diode.
04953-019
+IN VREF1 +VSOUT
–IN GND VREF2 NC
INDUCTIVE
LOAD
AD8206
CLAMP
DIODE
42V
BATTERY SHUNT
SWITCH
NC = NO CONNECT
5V
Figure 22. Low-Side Switch
HIGH-SIDE CURRENT SENSE WITH A HIGH-SIDE
SWITCH
This configuration minimizes the possibility of unexpected
solenoid activation and excessive corrosion (see Figure 23). In
this case, both the switch and the shunt are on the high side.
When the switch is off, this removes the battery from the load,
which prevents damage from potential shorts to ground, while
still allowing the recirculating current to be measured and
providing for diagnostics. Removing the power supply from the
load for the majority of the time minimizes the corrosive effects
that could be caused by the differential voltage between the load
and ground.
When using a high-side switch, the battery voltage is connected
to the load when the switch is closed, causing the common-mode
voltage to increase to the battery voltage. In this case, when the
switch is opened, the voltage reversal across the inductive load
causes the common-mode voltage to be held one diode drop
below ground by the clamp diode.
04953-020
+IN V
REF
1+V
S
OUT
–IN GND V
REF
2NC
INDUCTIVE
LOAD
AD8206
CLAMP
DIODE
42V
BATTERY SHUNT
SWITCH
NC = NO CONNECT
5V
Figure 23. High-Side Switch
Another typical application for the AD8206 is as part of the
control loop in H-bridge motor control. In this case, the
AD8206 is placed in the middle of the H-bridge (see Figure 24)
so that it can accurately measure current in both directions by
using the shunt available at the motor. This is a better solution
than a ground referenced op amp because ground is not typically a
stable reference voltage in this type of application. This instability
in the ground reference causes the measurements that could be
made with a simple ground referenced op amp to be inaccurate.
The AD8206 measures current in both directions as the H-bridge
switches and the motor changes direction. The output of the
AD8206 is configured in an external reference bidirectional
mode, see the Output Offset Adjustment section.
04953-021
+IN V
REF
1 +V
S
OUT
–IN GND V
REF
2 NC
AD8206
SHUNT
5V
2.5V
5V
CONTROLLER
NC = NO CONNECT
MOTOR
Figure 24. Motor Control Application
Rev. C | Page 12 of 13
Data Sheet AD8206
Rev. C | Page 13 of 13
OUTLINE DIMENSIONS
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
COMPLIANT TO JEDEC STANDARDS MS-012-AA
012407-A
0.25 (0.0098)
0.17 (0.0067)
1.27 (0.0500)
0.40 (0.0157)
0.50 (0.0196)
0.25 (0.0099) 45°
1.75 (0.0688)
1.35 (0.0532)
SEATING
PLANE
0.25 (0.0098)
0.10 (0.0040)
4
1
85
5.00(0.1968)
4.80(0.1890)
4.00 (0.1574)
3.80 (0.1497)
1.27 (0.0500)
BSC
6.20 (0.2441)
5.80 (0.2284)
0.51 (0.0201)
0.31 (0.0122)
COPLANARITY
0.10
Figure 25. 8-Lead Standard Small Outline Package [SOIC_N]
Narrow Body (R-8)
Dimensions shown in millimeters and (inches)
ORDERING GUIDE
Model1, 2 Temperature Range Package Description Package Option
AD8206YRZ −40°C to +125°C 8-Lead SOIC_N R-8
AD8206YRZ-REEL −40°C to +125°C 8-Lead SOIC_N, 13” Tape and Reel R-8
AD8206YRZ-REEL7 −40°C to +125°C 8-Lead SOIC_N, 7” Tape and Reel R-8
AD8206WYRZ −40°C to +125°C 8-Lead SOIC_N R-8
AD8206WYRZ-R7 −40°C to +125°C 8-Lead SOIC_N, 7” Tape and Reel R-8
AD8206WYRZ-RL −40°C to +125°C 8-Lead SOIC_N, 13” Tape and Reel R-8
AD8206WHRZ −40°C to +150°C 8-Lead SOIC_N R-8
AD8206WHRZ-RL −40°C to +150°C 8-Lead SOIC_N, 13” Tape and Reel R-8
1 Z = RoHS Compliant Part.
2 W = Qualified for Automotive Applications.
AUTOMOTIVE PRODUCTS
The AD8206W models are available with controlled manufacturing to support the quality and reliability requirements of automotive
applications. Note that these automotive models may have specifications that differ from the commercial models; therefore, designers
should review the Specifications section of this data sheet carefully. Only the automotive grade products shown are available for use in
automotive applications. Contact your local Analog Devices account representative for specific product ordering information and to
obtain the specific Automotive Reliability reports for these models.
©2005–2014 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D04953-0-11/14(C)
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Analog Devices Inc.:
AD8206WHRZ AD8206WHRZ-RL AD8206WYRZ AD8206WYRZ-R7 AD8206WYRZ-RL AD8206YRZ AD8206YRZ-
REEL AD8206YRZ-REEL7