MOTOROLA Freescale Semiconductor, Inc. Order this document by MC68CK338TS/D SEMICONDUCTOR TECHNICAL DATA MC68CK338 Technical Summary 32-Bit Modular Microcontroller Freescale Semiconductor, Inc... 1 Introduction The MC68CK338, a highly-integrated 32-bit microcontroller, combines high-performance data manipulation capabilities with powerful peripheral subsystems. The MCU is built up from standard modules that interface through a common intermodule bus (IMB). Standardization facilitates rapid development of devices tailored for specific applications. The MCU incorporates a low-power 32-bit CPU (CPU32L), a low-power system integration module (SIML), a queued serial module (QSM), and a configurable timer module 6 (CTM6). The MCU clock can either be synthesized from an external reference or input directly. Operation with a 32.768 kHz reference frequency is standard. The maximum system clock speed is 14.4 MHz. System hardware and software allow changes in clock rate during operation. Because MCU operation is fully static, register and memory contents are not affected by clock rate changes. High-density complementary metal-oxide semiconductor (HCMOS) architecture and 3V nominal operation make the basic power consumption of the MCU low. Power consumption can be minimized by either stopping the system clock, or alternatively, stopping the system clock only at the CPU32L, and allowing the other modules to continue operation. The CPU32 instruction set includes a low-power stop (LPSTOP) command that allows either of these power saving modes. The CTM6 includes new features such as a port I/O submodule, a 64-byte RAM submodule and a real time clock submodule. Refer to the Motorola Microcontroller Technologies Group Web page at http://www.mcu.sps.mot.com for the most current listing of device errata and customer information. Table 1 Ordering Information Package Type Frequency (MHz) Voltage Temperature Package Order Quantity Order Number 144-Pin TQFP 14.4 MHz 2.7V to 3.6V - 40 to + 85 C 2 pc tray 60 pc tray 300 pc tray SPMC68CK338CPV14 MC68CK338CPV14 MC68CK338CPV14B1 This document contains information on a new product. Specifications and information herein are subject to change without notice. (c) MOTOROLA INC., 1996 M For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. TABLE OF CONTENTS Section 1 Introduction 1.1 1.2 1.3 1.4 1.5 2 2.1 2.2 2.3 2.4 2.5 Freescale Semiconductor, Inc... 3 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 3.10 4 4.1 4.2 4.3 4.4 4.5 4.6 4.7 5 5.1 5.2 5.3 5.4 5.5 5.6 6 6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8 6.9 6.10 6.11 6.12 6.13 6.14 6.15 7 Page 1 Features ......................................................................................................................................3 Block Diagram .............................................................................................................................4 Pin Assignments ..........................................................................................................................5 Address Map ...............................................................................................................................6 Intermodule Bus ..........................................................................................................................6 Signal Descriptions 7 Pin Characteristics ......................................................................................................................7 MCU Power Connections ............................................................................................................8 MCU Driver Types .......................................................................................................................8 Signal Characteristics ..................................................................................................................9 Signal Function ..........................................................................................................................10 Low-Power System Integration Module 12 Overview ...................................................................................................................................12 System Configuration Block ......................................................................................................14 System Clock ............................................................................................................................16 System Protection Block ...........................................................................................................22 External Bus Interface ...............................................................................................................26 Chip-Selects ..............................................................................................................................30 General-Purpose Input/Output ..................................................................................................38 Resets .......................................................................................................................................41 Interrupts ...................................................................................................................................44 Factory Test Block .....................................................................................................................47 Low-Power Central Processor Unit 48 Overview ...................................................................................................................................48 Programming Model ..................................................................................................................48 Status Register ..........................................................................................................................50 Data Types ................................................................................................................................51 Addressing Modes .....................................................................................................................51 Instruction Set Summary ...........................................................................................................51 Background Debugging Mode ...................................................................................................56 Queued Serial Module 57 Overview ...................................................................................................................................57 Address Map .............................................................................................................................58 Pin Function ..............................................................................................................................59 QSM Registers ..........................................................................................................................59 QSPI Submodule .......................................................................................................................64 SCI Submodule .........................................................................................................................72 Configurable Timer Module 6 78 Overview ...................................................................................................................................78 Address Map .............................................................................................................................80 Time Base Bus System .............................................................................................................82 Bus Interface Unit Submodule (BIUSM) ....................................................................................84 Counter Prescaler Submodule (CPSM) ....................................................................................85 Clock Sources for Counter Submodules ...................................................................................87 Free-Running Counter Submodule (FCSM) ..............................................................................87 Modulus Counter Submodule (MCSM) .....................................................................................90 Single Action Submodule (SASM) .............................................................................................93 Double-Action Submodule (DASM) ...........................................................................................97 Real-Time Clock Submodule (RTCSM) with Low-Power Oscillator ........................................104 Parallel Port I/O Submodule (PIOSM) .....................................................................................107 Static RAM Submodule (RAMSM) ..........................................................................................108 RTCSM and RAMSM Standby Operation ...............................................................................108 CTM6 Interrupts ......................................................................................................................109 Electrical Characteristics 111 MOTOROLA 2 For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc... Freescale Semiconductor, Inc. 1.1 Features * Modular Architecture * Low-Power Central Processing Unit (CPU32L) -- Virtual memory implementation -- Loop mode of instruction execution -- Improved exception handling for controller applications -- Table lookup and interpolate instruction -- CPU-only LPSTOP operation/normal MCU LPSTOP operation * Low-Power System Integration Module (SIML) -- External bus support -- Twelve programmable chip-select outputs -- System protection logic -- On-chip PLL for system clock -- Watchdog timer, clock monitor, and bus monitor -- Expanded LPSTOP operation * Queued Serial Module (QSM) -- Enhanced serial communication interface (SCI) -- Queued serial peripheral interface (QSPI) -- Dual function I/O ports * Configurable Timer Module 6 (CTM6) -- One bus interface unit submodule (BIUSM) -- One counter prescaler submodule (CPSM) -- Three modulus counter submodules (MCSM) -- One free-running counter submodule (FCSM) -- Eleven double action submodules (DASM) -- Four (eight channels) single action submodules (SASM) -- One real time clock submodule (RTCSM) -- One port I/O submodule (PIOSM) -- Two 32-byte RAM submodules (RAMSM) MC68CK338 MC68CK338TS/D For More Information On This Product, Go to: www.freescale.com MOTOROLA 3 Freescale Semiconductor, Inc. 1.2 Block Diagram CTS14A CTS14B CTS18A CTS18B CTS24A CTS24B FC2 FC1 FC0 CTM6 CTD[10:4] CTD[29:26] CTM31L 64 BYTES 2 RAMSM ADDR23/CS10 PC6/ADDR22/CS9 PC5/ADDR21/CS8 PC4/ADDR20/CS7 PC3/ADDR19/CS6 PC2/FC2/CS5 PC1/FC1/CS4 PC0/FC0/CS3 BGACK/CS2 BG/CS1 BR/CS0 ADDR[23:19] 1 PIOSM CTIO[5:0] CTD[10:4] ADDR[23:0] ADDR[18:0] SIZ1 SIZ0 AS DS RMC AVEC DSACK1 DSACK0 PE7/SIZ1 PE6/SIZ0 PE5/AS PE4/DS PE3/RMC PE2/AVEC PE1/DSACK1 PE0/DSACK0 1 RTCSM IMB CONTROL PORT E CTM31L 11 DASM 4 SASM CTD[29:26] CSBOOT BR BG BGACK CS[10:0] 3 MCSM PQS7/TXD PQS6/PCS3 PQS5/PCS2 PQS4/PCS1 PQS3/PCS0/SS PQS2/SCK PQS1/MOSI PQS0/MISO PORTQS CONTROL RXD EBI SS TXD PCS3 PCS2 PCS1 PCS0 SCK MOSI MISO DATA[15:0] QSM DATA[15:0] R/W RESET HALT BERR CPU32L CONTROL PORT F IRQ[7:1] MODCLK BKPT IFETCH IPIPE DSI DSO DSCLK FREEZE TSC QUOT CONTROL TEST BKPT/DSCLK IFETCH/DSI IPIPE/DSO PF7/IRQ7 PF6/IRQ6 PF5/IRQ5 PF4/IRQ4 PF3/IRQ3 PF2/IRQ2 PF1/IRQ1 PF0/MODCLK CLKOUT XTAL EXTAL XFC VDDSYN CLOCK CONTROL Freescale Semiconductor, Inc... CTIO[5:0] PORT CT CTS14A CTS14B CTS18A CTS18B CTS24A CTS24B CHIP SELECTS 1 FCSM CONTROL PORT C VRTC VSSRTCOSC EXRTC XRTC VSSRTCOSC VRTC VSSRTCOSC EXRTC XRTC VSSRTCOSC TSC FREEZE/QUOT 338 BLOCK Figure 1 MC68CK338 Block Diagram MOTOROLA 4 For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 MC68CK338 108 107 106 104 104 103 102 101 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 VDDE NC NC NC FC0/CS3 BGACK/CS2 BG/CS1 BR/CS0 CSBOOT DATA0 DATA1 DATA2 DATA3 DATA4 DATA5 DATA6 DATA7 VSSI DATA8 DATA9 DATA10 DATA11 DATA12 DATA13 DATA14 DATA15 ADDR0 DSACK0 DSACK1 AVEC RMC DS AS SIZ0 SIZ1 VDDE 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 VDDE CTD6 CTD7 CTD8 CTD9 CTD10 CTIO1 CTIO0 VRTC MISO MOSI SCK PCS0/SS PCS1 PCS2 PCS3 TXD VSSI RXD ADDR1 ADDR2 ADDR3 ADDR4 ADDR5 ADDR6 ADDR7 ADDR8 ADDR9 ADDR10 ADDR11 ADDR12 ADDR13 ADDR14 ADDR15 ADDR16 VDDE NC NC NC VSSE ADDR17 ADDR18 IPIPE/DSO IFETCH/DSI BKPT/DSCLK TSC FREEZE/QUOT VSSI XTAL VDDSYN EXTAL VDDI XFC VDDE CLKOUT VSSE RESET HALT BERR IRQ7 IRQ6 IRQ5 IRQ4 IRQ3 IRQ2 IRQ1 MODCLK R/W VSSE NC NC NC Freescale Semiconductor, Inc... 144 143 142 141 140 139 138 137 136 135 134 133 132 131 130 129 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109 NC VSSE CTD5 CTD4 VSSRTCOSC XRTC EXRTC VSSRTCOSC CTIO2 CTIO3 CTS14B CTS14A CTIO4 CTIO5 CTS18B CTS18A CTS24B CTS24A VSSI VDDI CTD29 CTD28 CTD27 CTD26 CTM31L ADDR23/CS10 ADDR22/CS9 ADDR21/CS8 ADDR20/CS7 ADDR19/CS6 FC2/CS5 FC1/CS4 VSSE NC NC NC 1.3 Pin Assignments 338 144-PIN QFP Figure 2 MC68CK338 Pin Assignments MC68CK338 MC68CK338TS/D For More Information On This Product, Go to: www.freescale.com MOTOROLA 5 Freescale Semiconductor, Inc. 1.4 Address Map Figure 3 shows a map of the MCU internal addresses. Unimplemented blocks are mapped externally. $YFF400 CTM6 512 BYTES $YFF5FF $YFFA00 Freescale Semiconductor, Inc... SIML 128 BYTES $YFFA7F $YFFC00 QSM 512 BYTES $YFFDFF Y = M111, WHERE M IS THE STATE OF THE MODULE MAPPING (MM) BIT IN THE SIML CONFIGURATION REGISTER. 338 ADDRESS MAP Figure 3 MC68CK338 Address Map 1.5 Intermodule Bus The IMB is a standardized bus developed to facilitate design and operation of modular microcontrollers. It contains circuitry that supports exception processing, address space partitioning, multiple interrupt levels, and vectored interrupts. The standardized modules in the MCU communicate with one another and with external components via the IMB. The IMB uses 24 address lines and 16 data lines. MOTOROLA 6 For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. 2 Signal Descriptions 2.1 Pin Characteristics Table 2 shows MCU pins and their characteristics. All inputs detect CMOS logic levels. All inputs can be put in a high-impedance state, but the method of doing this differs depending upon pin function. Refer to Table 4 for a description of output drivers. An entry in the discrete I/O column of Table 2 indicates that a pin has an alternate I/O function. The port designation is given when it applies. Refer to Figure 1 for information about port organization. Freescale Semiconductor, Inc... Table 2 MCU Pin Characteristics Pin Mnemonic Output Driver Input Synchronized Input Hysteresis Discrete I/O Port Designation ADDR23/CS10 A Yes No -- -- ADDR[22:19]/CS[9:6] A Yes No O PC[6:3] ADDR[18:0] A Yes No -- -- AS B Yes No I/O PE5 AVEC B Yes No I/O PE2 BERR B Yes1 No -- -- BG/CS1 B -- -- -- -- BGACK/CS2 B Yes No -- -- BKPT/DSCLK -- Yes Yes -- -- BR/CS0 B Yes No -- -- CLKOUT A -- -- -- -- CSBOOT B -- -- -- -- CTD[29:26] Ao Yes Yes I/O -- CTD[10:4] Ao Yes Yes I/O -- CTIO[5:0] A Yes Yes I/O -- CTM31L A Yes Yes I -- CTS24[B:A] A Yes Yes I/O -- CTS18[B:A] A Yes Yes I/O -- CTS14[B:A] A Yes Yes I/O -- 2 DATA[15:0] Aw Yes No -- -- DS B Yes No I/O PE4 DSACK[1:0] B Yes No I/O PE[1:0] DSI/IFETCH A Yes Yes -- -- DSO/IPIPE A -- -- -- -- EXRTC -- -- Yes -- -- EXTAL -- -- Yes -- -- FC[2:0]/CS[5:3] A Yes No O PC[2:0] FREEZE/QUOT A -- -- -- -- HALT Bo Yes1 No -- -- IRQ[7:1] B Yes Yes I/O PF[7:1] MISO Bo Yes2 Yes I/O PQS0 MODCLK B Yes2 No I/O PF0 MOSI Bo Yes2 Yes I/O PQS1 MC68CK338 MC68CK338TS/D For More Information On This Product, Go to: www.freescale.com MOTOROLA 7 Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... Table 2 MCU Pin Characteristics (Continued) Pin Mnemonic Output Driver Input Synchronized Input Hysteresis Discrete I/O Port Designation PCS0/SS Bo Yes2 Yes I/O PQS3 PCS[3:1] Bo Yes2 Yes I/O PQS[6:4] RESET Bo Yes Yes -- -- RMC A Yes Yes I/O PE3 R/W A Yes No -- -- RXD -- No Yes -- -- SCK Bo Yes2 Yes I/O PQS2 SIZ[1:0] B Yes No I/O PE[7:6] TSC -- Yes Yes -- -- TXD Bo 2 Yes Yes I/O PQS7 XFC -- -- -- -- -- XRTC -- -- -- -- -- XTAL -- -- -- -- -- NOTES: 1. HALT and BERR synchronized only if late HALT or BERR. 2. DATA[15:0] synchronized during reset only. MODCLK and QSM pins synchronized only if used as port I/O pins. 2.2 MCU Power Connections Table 3 MCU Power Connections VDDSYN Clock Synthesizer VDDE, VSSE External periphery power (source and drain) VDDI, VSSI Internal module power (source and drain) VRTC RTCSM/RAMSM standby power VSSRTCOSC Ground connection for real-time clock oscillator 2.3 MCU Driver Types Table 4 MCU Output Driver Types Type A Output-only signals that are always driven; no external pull-up required Ao Type A output that can be operated in an open drain mode Aw Type A output with weak P-channel pull-up during reset B MOTOROLA 8 Description Three-state output that includes circuitry to pull up output before high impedance is established, to ensure rapid rise time. An external holding resistor is required to maintain logic level while the pin is in the high-impedance state. Bw Type B output with weak P-channel pull-up during reset Bo Type B output that can be operated in an open-drain mode For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. 2.4 Signal Characteristics Freescale Semiconductor, Inc... Table 5 MCU Signal Characteristics Signal Name MCU Module Signal Type Active State ADDR[23:0] SIML Bus -- AS SIML Output 0 AVEC SIML Input 0 BERR SIML Input 0 BG SIML Output 0 BGACK SIML Input 0 BKPT CPU32L Input 0 BR SIML Input 0 CLKOUT SIML Output -- CS[10:0] SIML Output 0 CSBOOT SIML Output 0 CTD[29:26] CTM6 Input/Output -- CTD[10:4] CTM6 Input/Output -- CTIO[5:0] CTM6 Input/Output -- CTM31L CTM6 Input -- CTS24[B:A] CTM6 Input/Output -- CTS18[B:A] CTM6 Input/Output -- CTS14[B:A] CTM6 Input/Output -- DATA[15:0] SIML Bus -- DS SIML Output 0 DSACK[1:0] SIML Input 0 DSCLK CPU32L Input Serial Clock DSI CPU32L Input -- DSO CPU32L Output -- EXRTC CTM6 Input -- EXTAL SIML Input -- FC[2:0] SIML Output -- FREEZE SIML Output 1 HALT SIML Input/Output 0 IFETCH CPU32L Output -- IPIPE CPU32L Output -- IRQ[7:1] SIML Input 0 MISO QSM Input/Output -- MODCLK SIML Input -- MOSI QSM Input/Output -- PC[6:0] SIML Output -- PCS[3:0] QSM Input/Output -- PE[7:0] SIML Input/Output -- PF[7:0] SIML Input/Output -- PQS[7:0] QSM Input/Output -- QUOT SIML Output -- MC68CK338 MC68CK338TS/D For More Information On This Product, Go to: www.freescale.com MOTOROLA 9 Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... Table 5 MCU Signal Characteristics (Continued) Signal Name MCU Module Signal Type Active State RESET SIML Input/Output 0 RMC SIML Output 0 R/W SIML Output 0 RXD QSM Input -- SCK QSM Input/Output -- SIZ[1:0] SIML Output -- SS QSM Input 0 TSC SIML Input -- TXD QSM Output -- XFC SIML Input -- XRTC CTM6 Output -- XTAL SIML Output -- 2.5 Signal Function Table 6 MCU Signal Function Signal Name Mnemonic Address Bus ADDR[23:0] Address Strobe AS Function 24-bit address bus Indicates that a valid address is on the address bus Autovector AVEC Requests an automatic vector during interrupt acknowledge Bus Error BERR Signals a bus error to the CPU Bus Grant BG Bus Grant Acknowledge BGACK Breakpoint BKPT Bus Request BR System Clockout CLKOUT System clock output Indicates that the MCU has relinquished the bus Indicates that an external device has assumed bus mastership Signals a hardware breakpoint to the CPU Indicates that an external device requires bus mastership Chip Selects CS[10:0] Select external devices at programmed addresses Boot Chip Select CSBOOT Chip select for external boot startup ROM Configurable Timer Double-Action CTD[29:26], CTD[10:4] Configurable Timer Modulus Counter Load CTM31L RTC Configurable Timer Oscillator EXRTC, XRTC Configurable Timer Port Input/Output CTIO[5:0] Configurable Timer Single-Action CTS24[B:A] CTS18[B:A] CTS14[B:A] Crystal Oscillator EXTAL, XTAL Data Bus DATA[15:0] MOTOROLA 10 Double-action submodule (DASM) signals. Can also be used as general purpose I/O pins External load for modulus counter. Can also be used as general purpose input CTM real time clock oscillator input/output General-purpose I/O pins Single-action submodule (SASM) signals. Can also be used as general purpose I/O pins Connections for clock synthesizer circuit reference; a crystal or an external oscillator can be used 16-bit data bus For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. Table 6 MCU Signal Function (Continued) Freescale Semiconductor, Inc... Signal Name Mnemonic Function Data Strobe DS Indicates that an external device should place valid data on the data bus during a read cycle and that valid data has been placed on the bus by the CPU during a write cycle Data and Size Acknowledge DSACK[1:0] Acknowledges to the SIML that data has been received for a write cycle, or that data is valid on the data bus for a read cycle Development Serial In, Out, Clock DSI, DSO, DSCLK Function Codes FC[2:0] Freeze FREEZE Halt HALT Instruction Pipeline IFETCH, IPIPE Interrupt Request Level IRQ[7:1] Master In Slave Out MISO Clock Mode Select MODCLK Serial I/O and clock for background debugging mode Identify processor state and current address space Indicates that the CPU has entered background mode Suspend external bus activity Indicate instruction pipeline activity Request interrupt service from the CPU Serial input to QSPI in master mode; serial output from QSPI in slave mode Selects system clock source Serial output from QSPI in master mode; serial input to QSPI in slave mode Master Out Slave In MOSI Port C PC[6:0] Peripheral Chip Select PCS[3:0] Port E PE[7:0] SIML digital input or output port signals Port F PF[7:0] SIML digital input or output port signals SIML digital output signals QSPI peripheral chip selects Port QS PQS[7:0] Quotient Out QUOT QSM digital I/O port signals Provides the quotient bit of the polynomial divider Reset RESET System reset Read-Modify-Write Cycle RMC Read/Write R/W Indicates the direction of data transfer on the bus SCI Receive Data RXD Serial input to the SCI QSPI Serial Clock SCK Clock output from QSPI in master mode; clock input to QSPI in slave mode Size SIZ[1:0] Slave Select SS Indicates an indivisible read-modify-write instruction Indicates the number of bytes to be transferred during a bus cycle Causes serial transmission when QSPI is in slave mode. Causes mode fault in master mode Three-State Control TSC Places all output drivers in a high-impedance state SCI Transmit Data TXD Serial output from the SCI External Filter Capacitor XFC MC68CK338 MC68CK338TS/D Connection for external phase-locked loop filter capacitor For More Information On This Product, Go to: www.freescale.com MOTOROLA 11 Freescale Semiconductor, Inc. 3 Low-Power System Integration Module The low-power system integration module (SIML) consists of five functional blocks that control system startup, initialization, configuration, and the external bus. Figure 4 shows the SIML block diagram. SYSTEM CONFIGURATION CLOCK SYNTHESIZER XTAL CLKOUT EXTAL MODCLK Freescale Semiconductor, Inc... SYSTEM PROTECTION CHIP-SELECTS CHIP-SELECTS EXTERNAL BUS EXTERNAL BUS INTERFACE RESET FACTORY TEST TSC FREEZE/QUOT 338 S(C)IM BLOCK Figure 4 SIML Block Diagram 3.1 Overview The system configuration block controls MCU configuration and operating mode. The clock synthesizer generates clock signals used by the SIML, other IMB modules, and external devices. In addition, a periodic interrupt generator supports execution of time-critical control routines. The system protection block provides bus and software watchdog monitors. The chip-select block provides eleven general-purpose chip-select signals and a boot ROM chip-select signal. Both general-purpose and boot ROM chip-select signals have associated base address registers and option registers. The external bus interface handles the transfer of information between IMB modules and external address space. The system test block incorporates hardware necessary for testing the MCU. It is used to perform factory tests, and its use in normal applications is not supported. Table 7 shows the SIML address map, which occupies 128 bytes. Unused registers within the 128-byte address space return zeros when read. The "Access" column indicates which registers are accessible only at the supervisor privilege level and which can be assigned to either the supervisor or user privilege level, according to the value of the SUPV bit in the SIMLCR. MOTOROLA 12 For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... Table 7 SIML Address Map Access Address1 S $YFFA00 S $YFFA02 SIML Test Register (SIMLTR) S $YFFA04 Clock Synthesizer Control Register (SYNCR) S $YFFA06 S $YFFA08 15 8 7 0 SIML Module Configuration Register (SIMLCR) Not Used Reset Status Register (RSR) SIML Test Register E (SIMLTRE) -- $YFFA0A Not Used -- $YFFA0C Not Used -- $YFFA0E Not Used S/U $YFFA10 Not Used S/U $YFFA12 Not Used Port E Data (PORTE1) S/U $YFFA14 Not Used Port E Data Direction (DDRE) S $YFFA16 Not Used Port E Pin Assignment (PEPAR) S/U $YFFA18 Not Used Port F Data (PORTF0) S/U $YFFA1A Not Used Port F Data (PORTF1) S/U $YFFA1C Not Used Port F Data Direction (DDRF) S $YFFA1E Not Used Port F Pin Assignment (PFPAR) S $YFFA20 Not Used System Protection Control (SYPCR) S $YFFA22 Periodic Interrupt Control Register (PICR) S $YFFA24 Periodic Interrupt Timer Register (PITR) S $YFFA26 S $YFFA28 Not Used S $YFFA2A Not Used S $YFFA2C Not Used S $YFFA2E Not Used S $YFFA30 Test Module Master Shift A (TSTMSRA) S $YFFA32 Test Module Master Shift B (TSTMSRB) S $YFFA34 Test Module Shift Count (TSTSC) S $YFFA36 Test Module Repetition Counter (TSTRC) S $YFFA38 Test Module Control (CREG) S/U $YFFA3A Test Module Distributed Register (DREG) -- $YFFA3C Not Used -- $YFFA3E Not Used S/U $YFFA40 -- $YFFA42 Not Used S $YFFA44 Chip-Select Pin Assignment (CSPAR0) S $YFFA46 Chip-Select Pin Assignment (CSPAR1) S $YFFA48 Chip-Select Base Boot (CSBARBT) S $YFFA4A Chip-Select Option Boot (CSORBT) S $YFFA4C Chip-Select Base 0 (CSBAR0) S $YFFA4E Chip-Select Option 0 (CSOR0) S $YFFA50 Chip-Select Base 1 (CSBAR1) MC68CK338 MC68CK338TS/D Port E Data (PORTE0) Not Used Software Service (SWSR) Not Used Port C Data (PORTC) For More Information On This Product, Go to: www.freescale.com MOTOROLA 13 Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... Table 7 SIML Address Map (Continued) Access Address1 S $YFFA52 Chip-Select Option 1 (CSOR1) S $YFFA54 Chip-Select Base 2 (CSBAR2) S $YFFA56 Chip-Select Option 2 (CSOR2) 15 8 7 0 S $YFFA58 Chip-Select Base 3 (CSBAR3) S $YFFA5A Chip-Select Option 3 (CSOR3) S $YFFA5C Chip-Select Base 4 (CSBAR4) S $YFFA5E Chip-Select Option 4 (CSOR4) S $YFFA60 Chip-Select Base 5 (CSBAR5) S $YFFA62 Chip-Select Option 5 (CSOR5) S $YFFA64 Chip-Select Base 6 (CSBAR6) S $YFFA66 Chip-Select Option 6 (CSOR6) S $YFFA68 Chip-Select Base 7 (CSBAR7) S $YFFA6A Chip-Select Option 7 (CSOR7) S $YFFA6C Chip-Select Base 8 (CSBAR8) S $YFFA6E Chip-Select Option 8 (CSOR8) S $YFFA70 Chip-Select Base 9 (CSBAR9) S $YFFA72 Chip-Select Option 9 (CSOR9) S $YFFA74 Chip-Select Base 10 (CSBAR10) S $YFFA76 Chip-Select Option 10 (CSOR10) -- $YFFA78 Not Used -- $YFFA7A Not Used -- $YFFA7C Not Used -- $YFFA7E Not Used NOTES: 1. Y = M111, where M is the logic state of the module mapping (MM) bit in the SIMLCR. 3.2 System Configuration Block This functional block provides configuration control for the entire MCU. It also performs interrupt arbitration, bus monitoring, and system test functions. 3.2.1 MCU Configuration The SIML controls MCU configuration during normal operation and during internal testing. SIMLCR -- SIML Configuration Register 15 14 13 EXOFF FRZSW FRZBM 12 11 10 0 SLVEN 0 0 DATA11 0 $YFFA00 9 8 SHEN 7 6 5 4 SUPV MM 0 0 1 1 0 0 3 2 1 0 IARB[3:0] RESET: 0 0 0 0 0 1 1 1 1 The SIML configuration register controls system configuration. It can be read or written at any time, except for the module mapping (MM) bit, which can be written only once. MOTOROLA 14 For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. EXOFF -- External Clock Off 0 = The CLKOUT pin is driven by the MCU system clock. 1 = The CLKOUT pin is placed in a high-impedance state. FRZSW -- Freeze Software Enable 0 = When FREEZE is asserted, the software watchdog and periodic interrupt timer counters continue to run. 1 = When FREEZE is asserted, the software watchdog and periodic interrupt timer counters are disabled, preventing interrupts while the MCU is in background debug mode. Freescale Semiconductor, Inc... FRZBM -- Freeze Bus Monitor Enable 0 = When FREEZE is asserted, the bus monitor continues to operate. 1 = When FREEZE is asserted, the bus monitor is disabled. SLVEN -- Factory Test Mode Enabled This bit is a read-only status bit that reflects the state of DATA11 during reset. 0 = IMB is not available to an external master. 1 = An external bus master has direct access to the IMB. SHEN[1:0] -- Show Cycle Enable This field determines what the EBI does with the external bus during internal transfer operations. A show cycle allows internal transfers to be externally monitored. Table 8 shows whether show cycle data is driven externally, and whether external bus arbitration can occur. To prevent bus conflict, external peripherals must not be enabled during show cycles. Table 8 Show Cycle Enable Bits SHEN Action 00 Show cycles disabled, external bus arbitration allowed 01 Show cycles enabled, external bus arbitration not allowed 10 Show cycles enabled, external bus arbitration allowed 11 Show cycles enabled, external bus arbitration allowed, internal activity is halted by a bus grant SUPV -- Supervisor/Unrestricted Data Space The SUPV bit places the SIML global registers in either supervisor or user data space. 0 = Registers with access controlled by the SUPV bit are accessible in either supervisor or user data space. 1 = Registers with access controlled by the SUPV bit are accessible in supervisor data space only. MM -- Module Mapping 0 = Internal modules are addressed from $7FF000 - $7FFFFF. 1 = Internal modules are addressed from $FFF000 - $FFFFFF. IARB[3:0] -- Interrupt Arbitration Field Each module that can generate interrupt requests has an interrupt arbitration (IARB) field. Arbitration between interrupt requests of the same priority is performed by serial contention between IARB field bit values. Contention must take place whenever an interrupt request is acknowledged, even when there is only a single pending request. An IARB field must have a non-zero value for contention to take place. If an interrupt request from a module with an IARB field value of %0000 is recognized, the CPU processes a spurious interrupt exception. Because the SIML routes external interrupt requests to the CPU, the SIML IARB field value is used for arbitration between internal and external interrupts of the same priority. The reset value of IARB for the SIML is %1111, and the reset value of IARB for all other modules is %0000, which prevents SIML interrupts from being discarded during initialization. MC68CK338 MC68CK338TS/D For More Information On This Product, Go to: www.freescale.com MOTOROLA 15 Freescale Semiconductor, Inc. 3.3 System Clock The system clock in the SIML provides timing signals for the IMB modules and for an external peripheral bus. Because the MCU is a fully static design, register and memory contents are not affected when the clock rate changes. System hardware and software support changes in clock rate during operation. The system clock signal can be generated in one of two ways. An internal phase-locked loop can synthesize the clock from a reference frequency, or the clock signal can be input directly from an external source. Keep these clock sources in mind while reading the rest of this section. Figure 5 is a block diagram of the system clock. Freescale Semiconductor, Inc... MODCLK EXTAL XTAL CRYSTAL OSCILLATOR PHASE COMPARATOR XFC VDDSYN LOW-PASS FILTER VCO FEEDBACK DIVIDER SYSTEM CLOCK CONTROL CLKOUT W Y X SYSTEM CLOCK 16/32 PLL BLOCK Figure 5 System Clock Block Diagram 3.3.1 Clock Sources The state of the clock mode (MODCLK) pin during reset determines the system clock source. When MODCLK is held high during reset, the clock synthesizer generates a clock signal from a reference frequency connected to the EXTAL pin. The clock synthesizer control register (SYNCR) determines operating frequency and mode of operation. When MODCLK is held low during reset, the clock synthesizer is disabled and an external system clock signal must be applied. The SYNCR control bits have no effect. The input clock is referred to as "fref", and can be either a crystal or an external clock source. The output of the clock system is referred to as "fsys". Ensure that fref and fsys are within normal operating limits. The reference frequency for this MCU is typically 32.768 kHz, but can range from 25 kHz to 50 kHz. To generate a reference frequency using the crystal oscillator, a reference crystal must be connected between the EXTAL and XTAL pins. Figure 6 shows a recommended circuit. MOTOROLA 16 For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. C1 22 pF* R1 4.7 k* XTAL R2 10M* EXTAL C2 22 pF* VSSI * RESISTANCE AND CAPACITANCE BASED ON A TEST CIRCUIT CONSTRUCTED WITH A DAISHINKU DMX-38 32.768 kHZ CRYSTAL. SPECIFIC COMPONENTS MUST BE BASED ON CRYSTAL TYPE. CONTACT CRYSTAL VENDOR FOR EXACT CIRCUIT. 338 OSCILLATOR Freescale Semiconductor, Inc... Figure 6 System Clock Oscillator Circuit When an external system clock signal is applied (PLL disabled, MODCLK = 0 during reset), the duty cycle of the input is critical, especially at operating frequencies close to maximum. The relationship between clock signal duty cycle and clock signal period is expressed: Minimum External Clock High/Low Time Minimum External Clock Period = -----------------------------------------------------------------------------------------------------------------------------------------------------------------------50 % - Percentage Variation of External Clock Input Duty Cycle When the system clock signal is applied directly to the EXTAL pin (PLL is disabled, MODCLK = 0 during reset), or the clock synthesizer reference frequency is supplied by a source other than a crystal (PLL enabled, MODCLK = 1 during reset), the XTAL pin must be left floating. In either case, the frequency of the signal applied to EXTAL may not exceed the maximum system clock frequency (PLL disabled) or the maximum clock synthesizer reference frequency (PLL enabled). 3.3.2 Clock Synthesizer Operation VDDSYN is used to power the clock circuits when the phase-locked loop is used. A separate power source increases MCU noise immunity and can be used to run the clock when the MCU is powered down. A quiet power supply must be used as the VDDSYN source. Adequate external bypass capacitors should be placed as close as possible to the VDDSYN pin to assure stable operating frequency. When an external system clock signal is applied and the PLL is disabled, VDDSYN should be connected to the VDD supply. Refer to the SIM Reference Manual (SIMRM/AD) for more information regarding system clock power supply conditioning. A voltage controlled oscillator (VCO) generates the system clock signal. To maintain a 50% clock duty cycle, the VCO frequency (fVCO) is either two or four times the system clock frequency, depending on the state of the X bit in SYNCR. A portion of the clock signal is fed back to a divider/counter. The divider controls the frequency of one input to a phase comparator. The other phase comparator input is the reference signal connected to the EXTAL pin. The comparator generates a control signal proportional to the difference in phase between the two inputs. The signal is low-pass filtered and used to correct the VCO output frequency. Filter circuit implementation can vary, depending upon the external environment and required clock stability. Figure 7 shows a recommended system clock filter network. XFC pin leakage must be kept within specified limits to maintain optimum stability and PLL performance. An external filter network connected to the XFC pin is not required when an external system clock signal is applied and the PLL is disabled. The XFC pin must be left floating in this case. MC68CK338 MC68CK338TS/D For More Information On This Product, Go to: www.freescale.com MOTOROLA 17 Freescale Semiconductor, Inc. C3 0.1F VDDSYN C1 0.1F XFC * VDDSYN C4 0.01F VSSI * MAINTAIN LOW LEAKAGE ON THE XFC NODE. 32 XFC CONN Freescale Semiconductor, Inc... Figure 7 System Clock Filter Network When the clock synthesizer is used, SYNCR determines the operating frequency of the MCU. The following equation relates the MCU operating frequency to the clock synthesizer reference frequency (fref) and the W, X, and Y fields in the SYNCR: f sys = 4f ref ( Y + 1 ) ( 2 2W + X ) The W bit controls a prescaler tap in the feedback divider. Setting W increases VCO speed by a factor of four. The Y field determines the count modulus for a modulo 64 downcounter, causing it to divide by a value of Y+1. When W or Y changes, VCO frequency (fVCO) changes, and the VCO must relock. The X bit controls a divide-by-two circuit that is not in the synthesizer feedback loop. When X=0 (reset state), the divider is enabled, and the system clock is one-fourth the VCO frequency. Setting X=1 disables the divider, doubling the clock speed without changing the VCO frequency. There is no relock delay when clock speed is changed by the X bit. Internal VCO frequency is determined by the following equations: f VCO = 4f sys if X = 0 or f VCO = 2f sys if X = 1 For the MCU to operate correctly, system clock and VCO frequencies selected by the W, X, and Y bits must be within the limits specified for the MCU. Do not use a combination of bit values that selects either an operating frequency or a VCO frequency greater than the maximum specified values. 3.3.3 Clock Synthesizer Control The clock synthesizer control circuits determine system clock frequency and clock operation under special circumstances, such as following loss of synthesizer reference or during low-power operation. Clock source is determined by the logic state of the MODCLK pin during reset. SYNCR -- Clock Synthesizer Control Register 15 14 W 13 12 11 X 10 9 $YFFA04 8 Y 7 6 5 4 EDIV STCPU 0 RSVD1 0 0 0 0 3 2 SLOCK RSVD1 1 0 STSIM STEXT 0 0 RESET: 0 0 1 1 1 1 1 1 U 0 NOTES: 1. Ensure that initialization software does not change the value of this bit (it should always be zero). MOTOROLA 18 For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. When the on-chip clock synthesizer is used, system clock frequency is controlled by the bits in the upper byte of SYNCR. Bits in the lower byte show the status of or control the operation of internal and external clocks. SYNCR can be read or written only when the CPU is operating in supervisor mode. W -- Frequency Control (VCO) This bit controls a prescaler tap in the synthesizer feedback loop. Setting it increases the VCO speed by a factor of four. VCO relock delay is required. X -- Frequency Control (Prescaler) This bit controls a divide by two prescaler that is not in the synthesizer feedback loop. Setting it doubles the clock speed without changing the VCO speed. No VCO relock delay is required. Freescale Semiconductor, Inc... Y[5:0] -- Frequency Control (Counter) The Y field controls the modulus down counter in the synthesizer feedback loop, causing it to divide by a value of Y + 1. Values range from 0 to 63. VCO relock delay is required. EDIV -- E Clock Divide Rate 0 = ECLK frequency is system clock divided by 8. 1 = ECLK frequency is system clock divided by 16. ECLK is an external M6800 bus clock available on pin ADDR23. Refer to 3.6 Chip-Selects for more information. STCPU -- Stop CPU32L Clock on LPSTOP 0 = When LPSTOP is executed, the intermodule bus clock (IMBCLK) is held low. When a trace, reset exception, or SIML interrupt occurs, the IMBCLK turns back on and the CPU32L begins executing instructions again. 1 = When LPSTOP is executed, the IMBCLK continues to run but is gated off and held low only where it enters the CPU32L. When a trace, reset exception, or interrupt from any module occurs, the IMBCLK is gated back on where it enters the CPU32L, and execution begins again. SLOCK -- Synthesizer Lock Flag 0 = VCO has not locked, but is enabled on the desired frequency. 1 = VCO has locked on the desired frequency, or is disabled. The MCU remains in reset until the synthesizer locks, but SLOCK does not indicate synthesizer lock status until after the user writes to SYNCR. STSIM -- Stop Mode SIML Clock 0 = When LPSTOP is executed, the SIML clock is driven by the crystal oscillator and the VCO is turned off to conserve power. 1 = When LPSTOP is executed, the SIML clock is driven by the VCO. STEXT -- Stop Mode External Clock 0 = When LPSTOP is executed, the CLKOUT signal is held negated to conserve power. 1 = When LPSTOP is executed, the CLKOUT signal is driven by the SIML clock, as determined by the state of the STSIM bit. 3.3.4 External MC6800 Bus Clock The state of the ECLK division rate bit (EDIV) in SYNCR determines clock rate for the ECLK signal available on pin ADDR23. ECLK is a bus clock for MC6800 devices and peripherals. ECLK frequency can be set to system clock frequency divided by eight or system clock frequency divided by sixteen. The clock is enabled by the CS10 field in chip-select pin assignment register 1 (CSPAR1). ECLK operation during low-power stop is described in the following paragraph. Refer to 3.6 Chip-Selects for more information about the external bus clock. MC68CK338 MC68CK338TS/D For More Information On This Product, Go to: www.freescale.com MOTOROLA 19 Freescale Semiconductor, Inc. 3.3.5 Low-Power Operation Low-power operation is initiated by the CPU32L. To reduce power consumption selectively, the CPU32L can enter the following low-power modes: 1. The CPU32L can selectively disable a module by setting the module's STOP bit. 2. The CPU32L can execute the STOP instruction. 3. The CPU32L can execute the LPSTOP instruction to stop the operations of only the CPU32L or the entire MCU, including the CPU32L. If the STOP bit in a module is set, then that module enters a low power mode. Some or all of that module's registers remain accessible. The module can be restarted by asserting RESET or by the CPU32L clearing the module's STOP bit. Freescale Semiconductor, Inc... The CPU32L can enter a low power mode by executing the STOP instruction. It can be reawakened by RESET, trace or interrupt. 3.3.5.1 Normal LPSTOP mode This low-power stop mode offers the greatest power reduction. To enter normal LPSTOP mode, the CPU32L executes the LPSTOP instruction after clearing the STCPU bit in SYNCR. This causes the SIML to turn off the system clock to most of the MCU. When the CPU executes LPSTOP, a special CPU space bus cycle writes a copy of the current interrupt mask into the clock control logic. The SIML brings the MCU out of normal LPSTOP mode when one of the following exceptions occurs: * RESET * Trace * SIML interrupt of higher priority than the stored interrupt mask During a LPSTOP, unless the system clock signal is supplied by an external source and that source is removed, the SIML clock control logic and the SIML clock signal (SIMCLK) continue to operate. The periodic interrupt timer and input logic for the RESET and IRQ pins are clocked by SIMCLK, and can be used to bring the processor out of LPSTOP. The software watchdog monitor cannot perform this function. Optionally, the SIML can also continue to generate the CLKOUT signal while in LPSTOP. STSIM and STEXT bits in SYNCR determine clock operation during LPSTOP. 3.3.5.2 Modified LPSTOP mode To enter modified LPSTOP mode, the CPU32L first sets the STCPU bit in SYNCR, then executes the LPSTOP instruction. This causes the SIML to turn off the system clock to the CPU32L only. The other MCU modules continue to operate. The SIML brings the MCU out of normal LPSTOP mode when one of the following exceptions occurs: * RESET * Trace * Interrupt of higher priority than the stored interrupt mask from any MCU module This low-power stop mode offers better power reduction than using the STOP instruction since the clock in the CPU32L is held inactive. Also, the STOP bits of individual modules may be set or cleared, leaving some active and others inactive. The flow chart shown in Figure 8 summarizes the effects of the STCPU, STSIM, and STEXT bits when the MCU enters normal or modified LPSTOP mode. NOTE To keep power consumption to a minimum when in LPSTOP mode, do not allow any spurious interrupts to occur. If a spurious interrupt occurs during LPSTOP mode, the device will transition to the STOP mode (which has greater power consumption) until a non-spurious interrupt request is detected by the CPU32L. MOTOROLA 20 For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. SETUP INTERRUPT TO WAKE UP MCU FROM LPSTOP LEAVE IMBCLK1 ON IN LPSTOP? NO YES Freescale Semiconductor, Inc... SET STOP BITS FOR MODULES THAT WILL NOT BE ACTIVE IN LPSTOP SET STCPU2 = 1 fimbclk = fsys IN LPSTOP USING EXTERNAL CLOCK? SET STCPU2 = 0 fimbclk = 0 Hz IN LPSTOP NO YES USE SYSTEM CLOCK AS SIMCLK IN LPSTOP? NO YES SET STSIM = 1 fsimclk3 = fsys IN LPSTOP WANT CLKOUT ON IN LPSTOP? NO WANT CLKOUT ON IN LPSTOP? YES SET STEXT = 1 fclkout4 = fsys feclk = / fsys IN LPSTOP SET STSIM = 0 fsimclk3 = fref IN LPSTOP NO YES SET STEXT = 0 fclkout4 = 0 Hz feclk = / 0 Hz IN LPSTOP SET STEXT = 1 fclkout4 = fref feclk = / 0 Hz IN LPSTOP SET STEXT = 0 fclkout4 = 0 Hz feclk = / 0 Hz IN LPSTOP ENTER LPSTOP NOTES: 1. IMBCLK IS THE CLOCK USED BY THE CPU32L, QSM, CTM6, AND THE SIML. 2. WHEN STCPU = 1, THE CPU32L IS SHUTDOWN IN LPSTOP. ALL OTHER MODULES WILL REMAIN ACTIVE UNLESS THE STOP BITS IN THEIR MODULE CONFIGURATION REGISTERS ARE SET PRIOR TO ENTERING LPSTOP. 3. THE SIMCLK IS USED BY THE PIT, IRQ, AND INPUT BLOCKS OF THE SIML. 4. CLKOUT CONTROL DURING LPSTOP IS OVERRIDDEN BY THE EXOFF BIT IN SIMLCR. IF EXOFF = 1, THE CLKOUT PIN IS ALWAYS IN A HIGH IMPEDANCE STATE AND STEXT HAS NO EFFECT IN LPSTOP. IF EXOFF = 0, CLKOUT IS CONTROLLED BY STEXT IN LPSTOP. WHEN STCPU = 1, THE CPU32L IS DISABLED IN LPSTOP, BUT ALL OTHER MODULES REMAIN ACTIVE OR STOPPED ACCORDING TO THE SETTING. LPSTOP FLOWCHART Figure 8 LPSTOP Flowchart MC68CK338 MC68CK338TS/D For More Information On This Product, Go to: www.freescale.com MOTOROLA 21 Freescale Semiconductor, Inc. 3.4 System Protection Block System protection includes a bus monitor, a halt monitor, a spurious interrupt monitor, and a software watchdog timer. These functions reduce the number of external components required for complete system control. Figure 9 shows the system protection block. MODULE CONFIGURATION AND TEST Freescale Semiconductor, Inc... RESET STATUS HALT MONITOR RESET REQUEST BUS MONITOR BERR SPURIOUS INTERRUPT MONITOR SOFTWARE WATCHDOG TIMER CLOCK RESET REQUEST PRESCALER 29 PERIODIC INTERRUPT TIMER IRQ[7:1] SYS PROTECT BLOCK Figure 9 System Protection Block 3.4.1 System Protection Control Register The system protection control register controls the software watchdog timer, bus monitor, and halt monitor. This register can be written only once following power-on or reset, but can be read at any time. SYPCR -- System Protection Control Register 15 14 13 12 11 10 NOT USED 9 $YFFA21 8 7 6 SWE SWP 1 MODCLK 5 4 SWT[1:0] 3 2 HME BME 0 0 1 0 BMT RESET: 0 0 0 0 SWE -- Software Watchdog Enable 0 = Software watchdog disabled 1 = Software watchdog enabled MOTOROLA 22 For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. SWP -- Software Watchdog Prescaler This bit controls the value of the software watchdog prescaler. 0 = Software watchdog clock not prescaled 1 = Software watchdog clock prescaled by 512 SWT[1:0] -- Software Watchdog Timing This field selects the divide ratio used to establish software watchdog time-out period. Table 9 gives the ratio for each combination of SWP and SWT bits. Freescale Semiconductor, Inc... Table 9 Software Watchdog Timing Field SWP SWT[1:0] Watchdog Time-Out Period 0 00 29 / fsys 0 01 211 / fsys 0 10 213 / fsys 0 11 215 / fsys 1 00 218 / fsys 1 01 220 / fsys 1 10 222 / fsys 1 11 224 / fsys HME -- Halt Monitor Enable 0 = Disable halt monitor function 1 = Enable halt monitor function BME -- Bus Monitor Enable 0 = Disable bus monitor function for internal to external bus cycles. 1 = Enable bus monitor function for internal to external bus cycles. BMT[1:0] -- Bus Monitor Timing This bit field selects the time-out period in system clocks for the bus monitor. Refer to Table 10. Table 10 Bus Monitor Time-Out Period BMT[1:0] Bus Monitor Time-Out Period 00 64 system clocks 01 32 system clocks 10 16 system clocks 11 8 system clocks 3.4.2 Bus Monitor The internal bus monitor checks for excessively long DSACK response times during normal bus cycles and for excessively long DSACK or AVEC response times during interrupt acknowledge (IACK) cycles. The monitor asserts BERR if the response time exceeds a user-specified time-out period. DSACK and AVEC response times are measured in clock cycles. The maximum allowable response time can be selected by setting the BMT[1:0] field. MC68CK338 MC68CK338TS/D For More Information On This Product, Go to: www.freescale.com MOTOROLA 23 Freescale Semiconductor, Inc. The monitor does not check DSACK response on the external bus unless the CPU initiates the bus cycle. The BME bit in SYPCR enables the internal bus monitor for internal to external bus cycles. If a system contains external bus masters, an external bus monitor must be implemented and the internal to external bus monitor option must be disabled. 3.4.3 Halt Monitor The halt monitor responds to assertion of the HALT signal on the internal bus caused by a double bus fault. A double bus fault occurs when: Freescale Semiconductor, Inc... * Bus error exception processing begins and a second BERR is detected before the first instruction of the first exception handler is executed. * One or more bus errors occur before the first instruction after a reset exception is executed. * A bus error occurs while the CPU is loading information from a bus error stack frame during a return from exception (RTE) instruction. If the halt monitor is enabled by setting HME in SYPCR, the MCU will issue a reset when a double bus fault occurs, otherwise the MCU will remain halted. A flag in the reset status register (RSR) indicates that the last reset was caused by the halt monitor. 3.4.4 Spurious Interrupt Monitor The spurious interrupt monitor issues BERR if no interrupt arbitration occurs during an interrupt acknowledge cycle. Leaving IARB[3:0] set to %0000 in the module configuration register of any peripheral that can generate interrupts will cause a spurious interrupt. 3.4.5 Software Watchdog The software watchdog is controlled by SWE in SYPCR. Once enabled, the watchdog requires that a service sequence be written to SWSR on a periodic basis. If servicing does not take place, the watchdog times out and issues a reset. This register can be written at any time, but returns zeros when read. SWSR -- Software Service Register 15 14 13 12 11 10 $YFFA27 9 8 7 6 5 4 NOT USED 3 2 1 0 0 0 0 0 SWSR RESET: 0 0 0 0 Each time the service sequence is written, the software watchdog timer restarts. The servicing sequence consists of the following steps: 1. Write $55 to SWSR. 2. Write $AA to SWSR. Both writes must occur before time-out in the order listed, but any number of instructions can be executed between the two writes. The watchdog clock rate is affected by SWP and SWT[1:0] in SYPCR. When SWT[1:0] are modified, a watchdog service sequence must be performed before the new time-out period takes effect. The reset value of SWP is affected by the state of the MODCLK pin on the rising edge of RESET. Refer to Table 11. MOTOROLA 24 For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. Table 11 MODCLK Pin States MODCLK SWP 0 1 1 0 3.4.6 Periodic Interrupt Timer The periodic interrupt timer (PIT) generates interrupts at user-programmable intervals. Timing for the PIT is provided by a programmable prescaler driven by the system clock. Freescale Semiconductor, Inc... PICR -- Periodic Interrupt Control Register 15 14 13 12 11 0 0 0 0 0 0 0 0 0 10 9 $YFFA22 8 7 6 5 4 PIRQL[2:0] 3 2 1 0 1 1 1 1 PIV[7:0] RESET: 0 0 0 0 0 0 0 0 This register contains information concerning periodic interrupt priority and vectoring. Bits [10:0] can be read or written at any time. Bits [15:11] are unimplemented and always return zero. PIRQL[2:0] -- Periodic Interrupt Request Level Table 12 shows what interrupt request level is asserted when a periodic interrupt is generated. If a PIT interrupt and an external IRQ signal of the same priority occur simultaneously, the PIT interrupt is serviced first. The periodic timer continues to run when the interrupt is disabled. Table 12 Periodic Interrupt Request Levels PIRQL[2:0] Interrupt Request Level 000 Periodic Interrupt Disabled 001 Interrupt Request Level 1 010 Interrupt Request Level 2 011 Interrupt Request Level 3 100 Interrupt Request Level 4 101 Interrupt Request Level 5 110 Interrupt Request Level 6 111 Interrupt Request Level 7 PIV[7:0] -- Periodic Interrupt Vector This bit field contains the vector generated in response to an interrupt from the periodic timer. When the SIML responds, the periodic interrupt vector is placed on the bus. PITR -- Periodic Interrupt Timer Register $YFFA24 15 14 13 12 11 10 9 8 0 0 0 0 0 0 0 PTP 0 0 0 0 0 0 MODCLK 7 6 5 4 3 2 1 0 0 0 0 PITM[7:0] RESET: 0 0 0 0 0 0 PITR contains the count value for the periodic timer. Setting the PITM[7:0] field turns off the periodic timer. This register can be read or written at any time. MC68CK338 MC68CK338TS/D For More Information On This Product, Go to: www.freescale.com MOTOROLA 25 Freescale Semiconductor, Inc. PTP -- Periodic Timer Prescaler Control 0 = Periodic timer clock not prescaled 1 = Periodic timer clock prescaled by 512 The reset state of PTP is the complement of the state of the MODCLK signal at the rising edge of RESET. PITM[7:0] -- Periodic Interrupt Timer Modulus This is an 8-bit timing modulus. The period of the timer can be calculated as follows: 4 ( PITM[7:0] ) ( Prescaler ) PIT Period = ----------------------------------------------------------------f ref where PIT Period = Periodic interrupt timer period Freescale Semiconductor, Inc... PITM[7:0] = Periodic interrupt timer register modulus fref = Synthesizer reference of external clock input frequency Prescaler = 1 if PTP = 0 or 512 if PTP = 1 3.5 External Bus Interface The external bus interface (EBI) transfers information between the internal MCU bus and external devices. The external bus has 24 address lines and 16 data lines. The EBI provides dynamic sizing between 8-bit and 16-bit data accesses. It supports byte, word, and long-word transfers. Ports are accessed through the use of asynchronous cycles controlled by the size (SIZ1 and SIZ0) and data size acknowledge (DSACK1 and DSACK0) pins. Multiple bus cycles may be required for dynamically sized transfer. Port width is the maximum number of bits accepted or provided during a bus transfer. External devices must follow the handshake protocol described below. Control signals indicate the beginning of the cycle, the address space, the size of the transfer, and the type of cycle. The selected device controls the length of the cycle. Strobe signals, one for the address bus and another for the data bus, indicate the validity of an address and provide timing information for data. The EBI operates in an asynchronous mode for any port width. To add flexibility and minimize the necessity for external logic, MCU chip-select logic can be synchronized with EBI transfers. Chip-select logic can also provide internally-generated bus control signals for these accesses. Refer to 3.6 Chip-Selects for more information. 3.5.1 Bus Control Signals The CPU initiates a bus cycle by driving the address, size, function code, and read/write outputs. At the beginning of the cycle, size signals SIZ0 and SIZ1 are driven along with the function code signals (FC[2:0]). The size signals indicate the number of bytes remaining to be transferred during an operand cycle. They are valid while the address strobe AS is asserted. Table 13 shows SIZ0 and SIZ1 encoding. The read/write (R/W) signal determines the direction of the transfer during a bus cycle. This signal changes state, when required, at the beginning of a bus cycle, and is valid while AS is asserted. The R/W signal only changes state when a write cycle is preceded by a read cycle or vice versa. The signal can remain low for two consecutive write cycles. MOTOROLA 26 For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. Table 13 Size Signal Encoding SIZ1 SIZ0 Transfer Size 0 1 Byte 1 0 Word 1 1 Three Byte 0 0 Long Word Freescale Semiconductor, Inc... 3.5.2 Function Codes The CPU32L automatically generates function code signals FC[2:0]. The function codes can be considered address extensions that automatically select one of eight address spaces to which an address applies. These spaces are designated as either user or supervisor, and program or data spaces. Address space seven is designated CPU space. CPU space is used for control information not normally associated with read or write bus cycles. Function codes are valid while AS is asserted. Table 14 displays CPU32L address space encodings. Table 14 CPU32L Address Space Encoding FC2 FC1 FC0 Address Space 0 0 0 Reserved 0 0 1 User Data Space 0 1 0 User Program Space 0 1 1 Reserved 1 0 0 Reserved 1 0 1 Supervisor Data Space 1 1 0 Supervisor Program Space 1 1 1 CPU Space 3.5.3 Address Bus Address bus signals ADDR[23:0] define the address of the most significant byte to be transferred during a bus cycle. The MCU places the address on the bus at the beginning of a bus cycle. The address is valid while AS is asserted. 3.5.4 Address Strobe AS is a timing signal that indicates the validity of an address on the address bus and the validity of many control signals. It is asserted one-half clock after the beginning of a bus cycle. 3.5.5 Data Bus Data bus signals DATA[15:0] make up a bidirectional, non-multiplexed parallel bus that transfers data to or from the MCU. A read or write operation can transfer 8 or 16 bits of data in one bus cycle. During a read cycle, the data is latched by the MCU on the last falling edge of the clock for that bus cycle. For a write cycle, all 16 bits of the data bus are driven, regardless of the port width or operand size. The MCU places the data on the data bus one-half clock cycle after AS is asserted in a write cycle. MC68CK338 MC68CK338TS/D For More Information On This Product, Go to: www.freescale.com MOTOROLA 27 Freescale Semiconductor, Inc. 3.5.6 Data Strobe Data strobe (DS) is a timing signal. For a read cycle, the MCU asserts DS to signal an external device to place data on the bus. DS is asserted at the same time as AS during a read cycle. For a write cycle, DS signals an external device that data on the bus is valid. The MCU asserts DS one full clock cycle after the assertion of AS during a write cycle. 3.5.7 Bus Cycle Termination Signals Freescale Semiconductor, Inc... During bus cycles, external devices assert the data size acknowledge signals DSACK1 and DSACK0. During a read cycle, the signals tell the MCU to terminate the bus cycle and to latch data. During a write cycle, the signals indicate that an external device has successfully stored data and that the cycle can end. These signals also indicate to the MCU the size of the port for the bus cycle just completed. Alternately, chip-selects can be used to generate DSACK1 and DSACK0 internally. Refer to 3.5.8 Dynamic Bus Sizing for more information. The bus error (BERR) signal is also a bus cycle termination indicator and can be used in the absence of DSACK1 and DSACK0 to indicate a bus error condition. It can also be asserted in conjunction with these signals, provided it meets the appropriate timing requirements. The internal bus monitor can be used to generate the BERR signal for internal-to-external transfers. When BERR and HALT are asserted simultaneously, the CPU takes a bus error exception. The autovector signal (AVEC) can terminate IRQ pin interrupt acknowledge cycles. AVEC indicates that the MCU will internally generate a vector number to locate an interrupt handler routine. If it is continuously asserted, autovectors will be generated for all external interrupt requests. AVEC is ignored during all other bus cycles. 3.5.8 Dynamic Bus Sizing The MCU dynamically interprets the port size of the addressed device during each bus cycle, allowing operand transfers to or from 8- and 16-bit ports. During an operand transfer cycle, the slave device signals its port size and indicates completion of the bus cycle to the MCU through the use of the DSACK1 and DSACK0 inputs, as shown in Table 15. Table 15 Effect of DSACK Signals DSACK1 DSACK0 Result 1 1 Insert Wait States in Current Bus Cycle 1 0 Complete Cycle -- Data Bus Port Size is 8 Bits 0 1 Complete Cycle -- Data Bus Port Size is 16 Bits 0 0 Reserved For example, if the MCU is executing an instruction that reads a long-word operand from a 16-bit port, the MCU latches the 16 bits of valid data and then runs another bus cycle to obtain the other 16 bits. The operation for an 8-bit port is similar, but requires four read cycles. The addressed device uses the DSACK0 and DSACK1 signals to indicate the port width. For instance, a 16-bit device always returns DSACK0 = 1 and DSACK1 = 0 for a 16-bit port, regardless of whether the bus cycle is a byte or word operation. Dynamic bus sizing requires that the portion of the data bus used for a transfer to or from a particular port size be fixed. A 16-bit port must reside on data bus bits [15:0] and an 8-bit port must reside on data bus bits [15:8]. This minimizes the number of bus cycles needed to transfer data and ensures that the MCU transfers valid data. MOTOROLA 28 For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. The MCU always attempts to transfer the maximum amount of data on all bus cycles. For a word operation, it is assumed that the port is 16 bits wide when the bus cycle begins. Operand bytes are designated as shown in Figure 10. OP0 is the most significant byte of a long-word operand, and OP3 is the least significant byte. The two bytes of a word-length operand are OP0 (most significant) and OP1. The single byte of a byte-length operand is OP0. OPERAND BYTE ORDER 31 LONG WORD 24 23 OP0 THREE BYTE WORD 16 15 87 OP1 OP2 OP3 OP0 OP1 OP2 OP0 OP1 OP0 BYTE Freescale Semiconductor, Inc... 0 OPERAND BYTE ORDER Figure 10 Operand Byte Order 3.5.9 Operand Alignment The data multiplexer establishes the necessary connections for different combinations of address and data sizes. The multiplexer takes the two bytes of the 16-bit bus and routes them to their required positions. Positioning of bytes is determined by the size and address outputs. SIZ1 and SIZ0 indicate the remaining number of bytes to be transferred during the current bus cycle. The number of bytes transferred is equal to or less than the size indicated by SIZ1 and SIZ0, depending on port width. ADDR0 also affects the operation of the data multiplexer. During an operand transfer, ADDR[23:1] indicate the word base address of the portion of the operand to be accessed, and ADDR0 indicates the byte offset from the base. 3.5.10 Misaligned Operands CPU32L processor architecture uses a basic operand size of 16 bits. An operand is misaligned when it overlaps a word boundary. This is determined by the value of ADDR0. When ADDR0 = 0 (an even address), the address is on a word and byte boundary. When ADDR0 = 1 (an odd address), the address is on a byte boundary only. A byte operand is aligned at any address; a word or long-word operand is misaligned at an odd address. The CPU32L does not support misaligned operand transfers, and gives an address error exception if one is attempted. The largest amount of data that can be transferred by a single bus cycle is an aligned word. If the MCU transfers a long-word operand via a 16-bit port, the most significant operand word is transferred on the first bus cycle and the least significant operand word on a following bus cycle. 3.5.11 Operand Transfer Cases Table 16 summarizes how operands are aligned for various types of transfers. OPn entries are portions of a requested operand that are read or written during a bus cycle and are defined by SIZ1, SIZ0, and ADDR0 for that bus cycle. MC68CK338 MC68CK338TS/D For More Information On This Product, Go to: www.freescale.com MOTOROLA 29 Freescale Semiconductor, Inc. Table 16 Operand Alignment Freescale Semiconductor, Inc... Current Cycle Transfer Case1 SIZ1 SIZ0 ADDR0 DSACK1 DSACK0 DATA [15:8] DATA [7:0] Next Cycle 1 Byte to 8-bit port (even) 0 1 0 1 0 OP0 (OP0)2 -- 2 Byte to 8-bit port (odd) 0 1 1 1 0 OP0 (OP0) -- 3 Byte to 16-bit port (even) 0 1 0 0 1 OP0 (OP0) -- 4 Byte to 16-bit port (odd) 0 1 1 0 1 (OP0) OP0 -- 5 Word to 8-bit port 1 0 0 1 0 OP0 (OP1) 2 6 Word to 16-bit port 1 0 0 0 1 OP0 OP1 -- 7 3-byte to 8-bit port3 1 1 1 1 0 OP0 (OP0) 5 8 Long word to 8-bit port 0 0 0 1 0 OP0 (OP0) 7 9 Long word to 16-bit port 0 0 0 0 1 OP0 OP1 6 NOTES: 1. All transfers are aligned. The CPU32L does not support misaligned word or long-word transfers. 2. Operands in parentheses are ignored by the CPU32L during read cycles. 3. 3-Byte transfer cases occur only as a result of a long word to 8-bit port transfer. 3.6 Chip-Selects Typical microcontrollers require additional hardware to provide external chip-select and address decode signals. The MC68338 includes 12 programmable chip-selects that can provide 2 to 16-clock-cycle access to external memory and peripherals. Address block sizes of two Kbytes to one Mbyte can be selected. Figure 11 is a functional diagram of a chip-select circuit. Chip-select assertion can be synchronized with bus control signals to provide output enable, read/write strobe, or interrupt acknowledge signals. Chip-select logic can also generate DSACK and AVEC signals internally. Each signal can also be synchronized with the ECLK signal available on ADDR23. INTERNAL SIGNALS BASE ADDRESS REGISTER ADDRESS ADDRESS COMPARATOR BUS CONTROL TIMING AND CONTROL PIN OPTION COMPARE OPTION REGISTER AVEC AVEC GENERATOR DSACK GENERATOR PIN ASSIGNMENT REGISTER PIN DATA REGISTER DSACK CHIP SEL BLOCK Figure 11 Chip-Select Circuit Block Diagram MOTOROLA 30 For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. When a memory access occurs, chip-select logic compares address space type, address, type of access, transfer size, and interrupt priority (in the case of interrupt acknowledge) to parameters stored in chip-select registers. If all parameters match, the appropriate chip-select signal is asserted. Select signals are active low. If a chip-select function is given the same address as a microcontroller module or an internal memory array, an access to that address goes to the module or array, and the chip-select signal is not asserted. The external address and data buses do not reflect the internal access. All chip-select circuits except CSBOOT are disabled out of reset. Chip-select option registers must not be written until base addresses have been written to the proper base address registers. Alternate functions for chip-select pins are enabled if appropriate data bus pins are held low at the release of RESET. Table 17 lists allocation of chip-selects and discrete outputs on the pins of the MCU. Freescale Semiconductor, Inc... Table 17 Chip-Select and Discrete Output Allocation Pin Chip-Select Discrete Outputs CSBOOT CSBOOT -- BR CS0 -- BG CS1 -- BGACK CS2 -- FC0 CS3 PC0 FC1 CS4 PC1 FC2 CS5 PC2 ADDR19 CS6 PC3 ADDR20 CS7 PC4 ADDR21 CS8 PC5 ADDR22 CS9 PC6 ADDR23 CS10 -- 3.6.1 Chip-Select Registers Each chip-select pin can have one or more functions. Chip-select pin assignment registers CSPAR[0:1] determine functions of the pins. Pin assignment registers also determine port size for dynamic bus allocation. A pin data register (PORTC) latches data for chip-select pins that are used for discrete output. Blocks of addresses are assigned to each chip-select function. Block sizes of two Kbytes to one Mbyte can be selected by writing values to the appropriate base address registers CSBARBT and CSBAR[0:10]. Multiple chip-selects assigned to the same block of addresses must have the same number of wait states. Chip-select option registers CSORBT and CSOR[0:10] determine timing of and conditions for assertion of chip-select signals. Eight parameters, including operating mode, access size, synchronization, and wait state insertion can be specified. Initialization software usually resides in a peripheral memory device controlled by the chip-select circuits. CSBOOT and registers CSORBT and CSBARBT are provided to support bootstrap operation. 3.6.2 Pin Assignment Registers The pin assignment registers contain twelve 2-bit fields that determine functions of the chip-select pins. Each pin has two or three possible functions, as shown in Table 18. MC68CK338 MC68CK338TS/D For More Information On This Product, Go to: www.freescale.com MOTOROLA 31 Freescale Semiconductor, Inc. Table 18 Chip-Select Pin Functions Assignment Register 16-Bit Chip-Select Alternate Function Discrete Output CSBOOT CSBOOT -- CS0 BR -- CS1 BG -- CS2 BGACK -- CS3 FC0 PC0 CS4 FC1 PC1 CS5 FC2 PC2 CS6 ADDR19 PC3 CS7 ADDR20 PC4 CS8 ADDR21 PC5 CS9 ADDR22 PC6 CS10 ADDR23 ECLK Freescale Semiconductor, Inc... CSPAR0 CSPAR1 Table 19 shows pin assignment field encoding. Pins that have no discrete output function do not use the %00 encoding. Table 19 Pin Assignment Encodings Bit Field Description 00 Discrete output 01 Alternate function 10 Chip-select (8-bit port) 11 Chip-select (16-bit port) CSPAR0 -- Chip-Select Pin Assignment Register 0 15 14 13 0 0 CS5PA[1:0] 12 11 10 CS4PA[1:0] 9 8 CS3PA[1:0] $YFFA44 7 6 CS2PA[1:0] 5 4 CS1PA[1:0] 3 2 CS0PA[1:0] 1 0 CSBTPA[1:0] RESET: 0 0 DATA2 1 DATA2 1 DATA2 1 DATA1 1 DATA1 1 DATA1 1 1 DATA0 CSPAR0 contains seven 2-bit fields that determine the functions of corresponding chip-select pins. CSPAR0[15:14] are not used. These bits always read zero; writes have no effect. CSPAR0 bit 1 always reads one; writes to CSPAR0 bit 1 have no effect. Table 20 shows CSPAR0 pin assignments. MOTOROLA 32 For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. Table 20 CSPAR0 Pin Assignments CSPAR0 Field Chip-Select Signal Alternate Signal Discrete Output CS5PA[1:0] CS5 FC2 PC2 CS4PA[1:0] CS4 FC1 PC1 CS3PA[1:0] CS3 FC0 PC0 CS2PA[1:0] CS2 BGACK -- CS1PA[1:0] CS1 BG -- CS0PA[1:0] CS0 BR -- CSBTPA[1:0] CSBOOT -- -- Freescale Semiconductor, Inc... CSPAR1 -- Chip-Select Pin Assignment Register 1 15 14 13 12 11 10 0 0 0 0 0 0 0 0 0 0 0 9 $YFFA46 8 7 CS10PA[1:0] 6 CS9PA[1:0] 5 4 CS8PA[1:0] 3 2 1 CS7PA[1:0] 0 CS6PA[1:0] RESET: 0 DATA71 1 DATA [7:6]1 1 DATA [7:5]1 1 DATA [7:4]1 1 DATA [7:3]1 1 NOTES: 1. Refer to Table 21 for CSPAR1 reset state information. The reset state of DATA[7:3] determines whether pins controlled by CSPAR1 are initially configured as high-order address lines or chip-selects. Table 21 shows the correspondence between DATA[7:3] and the reset configuration of CS[10:6]/ADDR[23:19]. Table 21 Reset Pin Function of CS[10:6] Data Bus Pins at Reset Chip-Select/Address Bus Pin Function CS9/ CS8/ CS7/ CS8/ CS10/ ADDR23 ADDR22 ADDR21 ADDR20 ADDR19 DATA7 DATA6 DATA5 DATA4 DATA3 1 1 1 1 1 CS10 CS9 CS8 CS7 CS6 1 1 1 1 0 CS10 CS9 CS8 CS7 ADDR19 1 1 1 0 X CS10 CS9 1 1 0 X X CS10 CS9 1 0 X X X CS10 0 X X X X CS8 ADDR20 ADDR19 ADDR21 ADDR20 ADDR19 ADDR22 ADDR21 ADDR20 ADDR19 ADDR23 ADDR22 ADDR21 ADDR20 ADDR19 CSPAR1 contains five 2-bit fields that determine the functions of corresponding chip-select pins. CSPAR1[15:10] are not used. These bits always read zero; writes have no effect. Table 22 shows CSPAR1 pin assignments. MC68CK338 MC68CK338TS/D For More Information On This Product, Go to: www.freescale.com MOTOROLA 33 Freescale Semiconductor, Inc. Table 22 CSPAR1 Pin Assignments CSPAR1 Field Chip-Select Signal Alternate Signal Discrete Output CS10PA[1:0] CS10 ADDR23 ECLK CS9PA[1:0] CS9 ADDR22 PC6 CS8PA[1:0] CS8 ADDR21 PC5 CS7PA[1:0] CS7 ADDR20 PC4 CS6PA[1:0] CS6 ADDR19 PC3 Freescale Semiconductor, Inc... Port size determines the way in which bus transfers to external addresses are allocated. Port size of eight bits or sixteen bits can be selected when a pin is assigned as a chip-select. Port size and transfer size affect how the chip-select signal is asserted. Refer to 3.6.4 Option Registers for more information. Out of reset, chip-select pin function is determined by the logic level on a corresponding data bus pin. These pins have weak internal pull-up drivers, but can be held low by external devices. Either 16-bit chip-select function (%11) or alternate function (%01) can be selected during reset. All pins except the boot ROM select pin (CSBOOT) are disabled out of reset. The CSBOOT signal is normally enabled out of reset. The state of the DATA0 line during reset determines what port width CSBOOT uses. If DATA0 is held high (either by the weak internal pull-up driver or by an external pull-up device), 16-bit width is selected. If DATA0 is held low, 8-bit port size is selected. A pin programmed as a discrete output drives an external signal to the value specified in the pin data register. No discrete output function is available on pins CSBOOT, BR, BG, or BGACK. ADDR23 provides ECLK output rather than a discrete output signal. When a pin is programmed for discrete output or alternate function, internal chip-select logic still functions and can be used to generate DSACK or AVEC internally on an address and control signal match. 3.6.3 Base Address Registers Each chip-select has an associated base address register. A base address is the lowest address in the block of addresses enabled by a chip-select. Block size is the extent of the address block above the base address. Block size is determined by the value contained in a BLKSZ field. Multiple chip-selects may be assigned to the same block of addresses so long as each chip-select uses the same number of wait states. The BLKSZ field determines which bits in the base address field are compared to corresponding bits on the address bus during an access. Provided other constraints determined by option register fields are also satisfied, when a match occurs, the associated chip-select signal is asserted. After reset, the MCU fetches the address of the first instruction to be executed from the reset vector, located beginning at address $000000 in program space. To support bootstrap operation from reset, the base address field in CSBARBT has a reset value of all zeros. A memory device containing the reset vector and an initialization routine can be automatically enabled by CSBOOT after a reset. The block size field in CSBARBT has a reset value of one Mbyte. CSBARBT -- Chip-Select Base Address Register Boot ROM $YFFA48 15 14 13 12 11 10 9 8 7 6 5 4 3 ADDR 23 ADDR 22 ADDR 21 ADDR 20 ADDR 19 ADDR 18 ADDR 17 ADDR 16 ADDR 15 ADDR 14 ADDR 13 ADDR 12 ADDR 11 0 0 0 0 0 0 0 0 0 0 0 2 1 0 BLKSZ[2:0] RESET: 0 0 MOTOROLA 34 For More Information On This Product, Go to: www.freescale.com 1 1 1 MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. CSBAR[0:10] -- Chip-Select Base Address Registers $YFFA4C-$YFFA74 15 14 13 12 11 10 9 8 7 6 5 4 3 ADDR 23 ADDR 22 ADDR 21 ADDR 20 ADDR 19 ADDR 18 ADDR 17 ADDR 16 ADDR 15 ADDR 14 ADDR 13 ADDR 12 ADDR 11 0 0 0 0 0 0 0 0 0 0 0 2 1 0 BLKSZ[2:0] RESET: 0 0 0 0 0 Freescale Semiconductor, Inc... ADDR[23:11] -- Base Address Field This field sets the starting address of a particular chip-select's address space. The address compare logic uses only the most significant bits to match an address within a block. The value of the base address must be a multiple of the block size. The base address register diagrams above show how register bits correspond to CPU address lines. BLKSZ[2:0] -- Block Size Field This field determines the size of the block that must be enabled by the chip-select. Table 23 shows bit encoding for the base address registers block size field. Table 23 Block Size Field Bit Encoding Block Size Field Block Size Address Lines Compared 000 2 Kbyte ADDR[23:11] 001 8 Kbyte ADDR[23:13] 010 16 Kbyte ADDR[23:14] 011 64 Kbyte ADDR[23:16] 100 128 Kbyte ADDR[23:17] 101 256 Kbyte ADDR[23:18] 110 512 Kbyte ADDR[23:19] 111 1 Mbyte ADDR[23:20] 3.6.4 Option Registers The option registers contain eight fields that determine timing of and conditions for assertion of chipselect signals. To assert a chip-select signal, and to provide DSACK or autovector support, other constraints set by fields in the option register and in the base address register must also be satisfied. CSORBT -- Chip-Select Option Register Boot ROM 15 14 MODE 13 BYTE[1:0] 12 11 R/W[1:0] 10 9 STRB 8 $YFFA4A 7 6 DSACK[3:0] 5 4 3 SPACE[1:0] 2 1 IPL[2:0] 0 AVEC RESET: 0 1 1 1 1 0 1 1 0 1 1 1 0 CSOR[0:10] -- Chip-Select Option Registers 15 14 MODE 13 BYTE[1:0] 12 11 R/W[1:0] 10 9 STRB 0 0 0 $YFFA4E-YFFA76 8 7 6 DSACK[3:0] 5 4 3 SPACE[1:0] 2 1 IPL[2:0] 0 AVEC RESET: 0 0 0 MC68CK338 MC68CK338TS/D 0 0 0 0 0 0 0 0 0 For More Information On This Product, Go to: www.freescale.com 0 0 0 0 MOTOROLA 35 Freescale Semiconductor, Inc. CSORBT, the option register for CSBOOT, contains special reset values that support bootstrap operation from peripheral memory devices. The following bit descriptions apply to both CSORBT and CSOR[0:10] option registers. MODE -- Asynchronous/Synchronous Mode 0 = Asynchronous mode (chip-select assertion determined by bus control signals) 1 = Synchronous mode (chip-select assertion synchronized with ECLK signal) In asynchronous mode, the chip-select is asserted synchronized with AS or DS. DSACK[3:0] is not used in synchronous mode because a bus cycle is only performed as a synchronous operation. When a match condition occurs on a chip-select programmed for synchronous operation, the chip-select signals the EBI that an ECLK cycle is pending. Freescale Semiconductor, Inc... BYTE[1:0] -- Upper/Lower Byte Option This field is used only when the chip-select 16-bit port option is selected in the pin assignment register. Table 24 lists upper/lower byte options. Table 24 Upper/Lower Byte Options BYTE[1:0] Description 00 Disable 01 Lower Byte 10 Upper Byte 11 Both Bytes R/W[1:0] -- Read/Write This field causes a chip-select to be asserted only for reads, only for writes, or for both reads and writes. Refer to Table 25 for options available. Table 25 R/W Encodings R/W[1:0] Description 00 Reserved 01 Read Only 10 Write Only 11 Read/Write STRB -- Address Strobe/Data Strobe 0 = Address strobe 1 = Data strobe This bit controls the timing for assertion of a chip-select in asynchronous mode. Selecting address strobe causes chip-select to be asserted synchronized with address strobe. Selecting data strobe causes chip-select to be asserted synchronized with data strobe. DSACK[3:0] -- Data and Size Acknowledge This field specifies the source of DSACK[3:0] in asynchronous mode. It also allows the user to adjust bus timing with internal DSACK[3:0] generation by controlling the number of wait states that are inserted to optimize bus speed in a particular application. Table 26 shows the DSACK[3:0] encoding. The fast termination encoding (%1110) is used for two-cycle access to external memory. MOTOROLA 36 For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... Table 26 DSACK Field Encoding DSACK[3:0] Clock Cycles Required Per Access Wait States Per Access 0000 3 0 Wait States 0001 4 1 Wait State 0010 5 2 Wait States 0011 6 3 Wait States 0100 7 4 Wait States 0101 8 5 Wait States 0110 9 6 Wait States 0111 10 7 Wait States 1000 11 8 Wait States 1001 12 9 Wait States 1010 13 10 Wait States 1011 14 11 Wait States 1100 15 12 Wait States 1101 16 13 Wait States 1110 2 Fast Termination 1111 -- External DSACK SPACE[1:0] -- Address Space Use this option field to select an address space for the chip-select logic. The CPU32L normally operates in supervisor or user space, but interrupt acknowledge cycles must take place in CPU space. Table 27 shows address space bit encodings. Table 27 Address Space Bit Encodings SPACE[1:0] Address Space 00 CPU Space 01 User Space 10 Supervisor Space 11 Supervisor/User Space IPL[2:0] -- Interrupt Priority Level If the space field is set for CPU space, chip-select logic can be used for interrupt acknowledge. During an interrupt acknowledge cycle, the priority level on address lines ADDR[3:1] is compared to the value in IPL[2:0]. If the values are the same, a chip-select is asserted, provided that other option register conditions are met. Table 28 shows IPL[2:0] encoding. MC68CK338 MC68CK338TS/D For More Information On This Product, Go to: www.freescale.com MOTOROLA 37 Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... Table 28 Interrupt Priority Level Field Encoding IPL[2:0] Interrupt Priority Level 000 Any Level 001 1 010 2 011 3 100 4 101 5 110 6 111 7 This field only affects the response of chip-selects and does not affect interrupt recognition by the CPU. Any level means that chip-select is asserted regardless of the level of the interrupt acknowledge cycle. AVEC -- Autovector Enable 0 = External interrupt vector enabled 1 = Autovector enabled This field selects one of two methods of acquiring an interrupt vector number during an external interrupt acknowledge cycle. If the chip-select is configured to trigger on an interrupt acknowledge cycle (SPACE[1:0] = %00) and the AVEC field is set to one, the chip-select circuit generates an internal AVEC signal in response to an external interrupt cycle, and the SIML supplies an automatic vector number. Otherwise, the vector number must be supplied by the requesting device. An internal autovector is generated only in response to interrupt requests from the SIML IRQ pins. Interrupt requests from other IMB modules are ignored. The AVEC bit must not be used in synchronous mode, as autovector response timing can vary because of ECLK synchronization. 3.6.5 Port C Data Register Bit values in port C determine the state of chip-select pins used for discrete output. When a pin is assigned as a discrete output, the value in this register appears at the output. This is a read/write register. Bit 7 is not used. Writing to this bit has no effect, and it always returns zero when read. PORTC -- Port C Data Register 15 14 13 12 11 $YFFA41 10 NOT USED 9 8 7 6 5 4 3 2 1 0 0 PC6 PC5 PC4 PC3 PC2 PC1 PC0 0 1 1 1 1 1 1 1 RESET: 3.7 General-Purpose Input/Output SIML pins can be configured as two general-purpose I/O ports, E and F. The following paragraphs describe registers that control the ports. MOTOROLA 38 For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. PORTE0, PORTE1-- Port E Data Register 15 14 13 12 11 10 9 $YFFA11, YFFA13 8 NOT USED 7 6 5 4 3 2 1 0 PE7 PE6 PE5 PE4 PE3 PE2 PE1 PE0 U U U U U U U U RESET: A write to the port E data register is stored in the internal data latch and, if any port E pin is configured as an output, the value stored for that bit is driven on the pin. A read of the port E data register returns the value at the pin only if the pin is configured as a discrete input. Otherwise, the value read is the value stored in the register. Freescale Semiconductor, Inc... The port E data register is a single register that can be accessed in two locations. When accessed at $YFFA11, the register is referred to as PORTE0; when accessed at $YFFA13, the register is referred to as PORTE1. The register can be read or written at any time. It is unaffected by reset. DDRE -- Port E Data Direction Register 15 14 13 12 11 10 $YFFA15 9 8 7 6 5 4 3 2 1 0 DDE7 DDE6 DDE5 DDE4 DDE3 DDE2 DDE1 DDE0 0 0 0 0 0 0 0 0 RESET: The bits in this register control the direction of the pin drivers when the pins are configured as I/O. Any bit in this register set to one configures the corresponding pin as an output. Any bit in this register cleared to zero configures the corresponding pin as an input. This register can be read or written at any time. PEPAR -- Port E Pin Assignment 15 14 13 12 11 $YFFA17 10 9 8 7 6 5 4 3 2 1 0 PEPA7 PEPA6 PEPA5 PEPA4 PEPA3 PEPA2 PEPA1 PEPA0 DATA8 DATA8 DATA8 DATA8 DATA8 DATA8 DATA8 DATA8 RESET: The bits in this register control the function of each port E pin. Any bit set to one configures the corresponding pin as a bus control signal, with the function shown in Table 29. Any bit cleared to zero defines the corresponding pin to be an I/O pin, controlled by PORTE and DDRE. Data bus bit 8 controls the state of this register following reset. If DATA8 is set to one during reset, the register is set to $FF, which defines all port E pins as bus control signals. If DATA8 is cleared to zero during reset, this register is set to $00, configuring all port E pins as I/O pins. MC68CK338 MC68CK338TS/D For More Information On This Product, Go to: www.freescale.com MOTOROLA 39 Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... Table 29 Port E Pin Assignments PEPAR Bit Port E Signal Bus Control Signal PEPA7 PE7 SIZ1 PEPA6 PE6 SIZ0 PEPA5 PE5 AS PEPA4 PE4 DS PEPA3 PE3 RMC PEPA2 PE2 AVEC PEPA1 PE1 DSACK1 PEPA0 PE0 DSACK0 PORTF0, PORTF1 -- Port F Data Register 15 14 13 12 11 10 9 $YFFA19, YFFA1B 8 NOT USED 7 6 5 4 3 2 1 0 PF7 PF6 PF5 PF4 PF3 PF2 PF1 PF0 U U U U U U U U RESET: The write to the port F data register is stored in the internal data latch, and if any port F pin is configured as an output, the value stored for that bit is driven onto the pin. A read of the port F data register returns the value at the pin only if the pin is configured as a discrete input. Otherwise, the value read is the value stored in the register. The port F data register is a single register that can be accessed in two locations. When accessed at $YFFA19, the register is referred to as PORTF0; when accessed at $YFFA1B, the register is referred to as PORTF1. The register can be read or written at any time. It is unaffected by reset. DDRF -- Port F Data Direction Register 15 14 13 12 11 10 $YFFA1D 9 8 NOT USED 7 6 5 4 3 2 1 0 DDF7 DDF6 DDF5 DDF4 DDF3 DDF2 DDF1 DDF0 0 0 0 0 0 0 0 0 RESET: The bits in this register control the direction of the pin drivers when the pins are configured as I/O. Any bit in this register set to one configures the corresponding pin as an output. Any bit in this register cleared to zero configures the corresponding pin as an input. This register can be read or written at any time. PFPAR -- Port F Pin Assignment Register 15 14 13 12 11 NOT USED 10 9 $YFFA1F 8 7 6 5 4 3 2 1 0 PFPA7 PFPA6 PFPA5 PFPA4 PFPA3 PFPA2 PFPA1 PFPA0 DATA9 DATA9 DATA9 DATA9 DATA9 DATA9 DATA9 DATA9 RESET: The bits in this register control the function of each port F pin. Any bit cleared to zero defines the corresponding pin to be an I/O pin. Any bit set to one defines the corresponding pin to be an interrupt request signal or MODCLK. The MODCLK signal has no function after reset. Table 30 shows port F pin assignments. MOTOROLA 40 For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... Table 30 Port F Pin Assignments PFPAR Field Port F Signal Alternate Signal PFPA7 PF7 IRQ7 PFPA6 PF6 IRQ6 PFPA5 PF5 IRQ5 PFPA4 PF4 IRQ4 PFPA3 PF3 IRQ3 PFPA2 PF2 IRQ2 PFPA1 PF1 IRQ1 PFPA0 PF0 MODCLK Data bus pin 9 controls the state of this register following reset. If DATA9 is set to one during reset, the register is set to $FF, which defines all port F pins as interrupt request inputs. If DATA9 is cleared to zero during reset, this register is set to $00, defining all port F pins as I/O pins. 3.8 Resets Reset procedures handle system initialization and recovery from catastrophic failure. The MCU performs resets with a combination of hardware and software. The SIML determines whether a reset is valid, asserts control signals, performs basic system configuration based on hardware mode-select inputs, then passes control to the CPU. Reset occurs when an active low logic level on the RESET pin is clocked into the SIML. Resets are gated by the CLKOUT signal. Asynchronous resets are assumed to be catastrophic. An asynchronous reset can occur on any clock edge. Synchronous resets are timed to occur at the end of bus cycles. If there is no clock when RESET is asserted, reset does not occur until the clock starts. Resets are clocked in order to allow completion of write cycles in progress at the time RESET is asserted. Reset is the highest-priority CPU32L exception. Any processing in progress is aborted by the reset exception, and cannot be restarted. Only essential tasks are performed during reset exception processing. Other initialization tasks must be accomplished by the exception handler routine. 3.8.1 SIML Reset Mode Selection The logic states of certain data bus pins during reset determine SIML operating configuration. In addition, the state of the MODCLK pin determines system clock source and the state of the BKPT pin determines what happens during subsequent breakpoint assertions. Table 31 is a summary of reset mode selection options. MC68CK338 MC68CK338TS/D For More Information On This Product, Go to: www.freescale.com MOTOROLA 41 Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... Table 31 Reset Mode Selection Mode Select Pin Default Function (Pin Left High) Alternate Function (Pin Pulled Low) DATA0 CSBOOT 16-Bit CSBOOT 8-Bit DATA1 CS0 CS1 CS2 BR BG BGACK DATA2 CS3 CS4 CS5 FC0 FC1 FC2 DATA3 DATA4 DATA5 DATA6 DATA7 CS6 CS[7:6] CS[8:6] CS[9:6] CS[10:6] ADDR19 ADDR[20:19] ADDR[21:19] ADDR[22:19] ADDR[23:19] DATA8 DSACK[1:0] AVEC, DS, AS SIZ[1:0] PORTE DATA9 IRQ[7:1] MODCLK PORTF DATA11 Test Mode Disabled Test Mode Enabled MODCLK VCO = System Clock EXTAL = System Clock BKPT Background Mode Disabled Background Mode Enabled Data lines have weak internal pull-up drivers. External bus loading can overcome the weak internal pullup drivers on data bus lines, and hold pins low during reset. Use an active device to hold data bus lines low. Data bus configuration logic must release the bus before the first bus cycle after reset to prevent conflict with external memory devices. The first bus cycle occurs ten CLKOUT cycles after RESET is released. If external mode selection logic causes a conflict of this type, an isolation resistor on the driven lines may be required. 3.8.2 Reset States of SIML Pins Generally, while RESET is asserted, SIML pins either go to an inactive high-impedance state or are driven to their inactive states. After RESET is released, mode selection occurs and reset exception processing begins. Pins configured as inputs must be driven to the desired active state. Pull-up or pulldown circuitry may be necessary. Pins configured as outputs begin to function after RESET is released. Table 32 is a summary of SIML pin states during reset. MOTOROLA 42 For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... Table 32 SIML Pin Reset States Pin State After RESET Released Pin(s) Pin State While RESET Asserted Pin Function Pin State Pin Function Pin State CS10/ADDR23/ECLK VDD CS10 VDD ADDR23 Unknown CS[9:6]/ADDR[22:19]/PC[6:3] VDD CS[9:6] VDD ADDR[22:19] Unknown ADDR[18:0] High-Z ADDR[18:0] Unknown ADDR[18:0] Unknown AS/PE5 High-Z AS Output PE5 Input AVEC/PE2 High-Z AVEC Input PE2 Input BERR High-Z BERR Input BERR Input CS1/BG VDD CS1 VDD BG VDD CS2/BGACK VDD CS2 VDD BGACK Input CS0/BR VDD CS0 VDD BR Input CLKOUT Output CLKOUT Output CLKOUT Output CSBOOT VDD CSBOOT VSS CSBOOT VSS DATA[15:0] Mode select DATA[15:0] Input DATA[15:0] Input Default Function Alternate Function DS/PE4 High-Z DS Output PE4 Input DSACK0/PE0 High-Z DSACK0 Input PE0 Input DSACK1/PE1 High-Z DSACK1 Input PE1 Input CS[5:3]/FC[2:0]/PC[2:0] VDD CS[5:3] VDD FC[2:0] Unknown HALT High-Z HALT Input HALT Input IRQ[7:1]/PF[7:1] High-Z IRQ[7:1] Input PF[7:1] Input MODCLK/PF0 Mode Select MODCLK Input PF0 Input R/W High-Z R/W Output R/W Output RESET Asserted RESET Input RESET Input RMC/PE3 High-Z RMC Output PE3 Input SIZ[1:0]/PE[7:6] High-Z SIZ[1:0] Unknown PE[7:6] Input TSC Mode select TSC Input TSC Input 3.8.3 Functions of Pins for Other Modules During Reset Generally, pins associated with modules other than the SIML default to port functions, and input/output ports are set to input state. This is accomplished by disabling pin functions in the appropriate control registers, and by clearing the appropriate port data direction registers. Refer to individual module sections in this manual for more information. 3.8.4 Reset Timing The RESET input must be asserted for a specified minimum period in order for reset to occur. External RESET assertion can be delayed internally for a period equal to the longest bus cycle time (or the bus monitor time-out period) in order to protect write cycles from being aborted by reset. While RESET is asserted, SIML pins are either in a disabled high-impedance state or are driven to their inactive states. When an external device asserts RESET for the proper period, reset control logic clocks the signal into an internal latch. The control logic drives the RESET pin low for an additional 512 CLKOUT cycles after it detects that the RESET signal is no longer being externally driven, to guarantee this length of reset to the entire system. MC68CK338 MC68CK338TS/D For More Information On This Product, Go to: www.freescale.com MOTOROLA 43 Freescale Semiconductor, Inc. If an internal source asserts the reset signal, the reset control logic asserts RESET for a minimum of 512 cycles. If the reset signal is still asserted at the end of 512 cycles, the control logic continues to assert RESET until the internal reset signal is negated. After 512 cycles have elapsed, the reset input pin goes to an inactive, high-impedance state for 10 cycles. At the end of this 10-cycle period, the reset input is tested. When the input is at logic level one, reset exception processing begins. If, however, the reset input is at logic level zero, the reset control logic drives the pin low for another 512 cycles. At the end of this period, the pin again goes to highimpedance state for ten cycles, then it is tested again. The process repeats until RESET is released. Freescale Semiconductor, Inc... 3.8.5 Power-On Reset When the SIML clock synthesizer is used to generate the system clock, power-on reset involves special circumstances related to application of system and clock synthesizer power. Regardless of clock source, voltage must be applied to clock synthesizer power input pin VDDSYN in order for the MCU to operate. The following discussion assumes that VDDSYN is applied before and during reset. This minimizes crystal start-up time. When VDDSYN is applied at power-on, start-up time is affected by specific crystal parameters and by oscillator circuit design. VDD ramp-up time also affects pin state during reset. During power-on reset, an internal circuit in the SIML drives the IMB and external reset lines. The circuit releases the internal reset line as VDD ramps up to the minimum specified value, and SIML pins are initialized. As VDD reaches a specified minimum value, the clock synthesizer VCO begins operation and clock frequency ramps up to specified limp mode frequency. The external RESET line remains asserted until the clock synthesizer PLL locks and 512 CLKOUT cycles elapse. The SIML clock synthesizer provides clock signals to the other MCU modules. After the clock is running and the internal reset signal is asserted for four clock cycles, these modules reset. VDD ramp time and VCO frequency ramp time determine how long these four cycles take. Worst case is approximately 15 milliseconds. During this period, module port pins may be in an indeterminate state. While input-only pins can be put in a known state by means of external pull-up resistors, external logic on input/output or output-only pins must condition the lines during this time. Active drivers require high-impedance buffers or isolation resistors to prevent conflict. 3.8.6 Use of Three-State Control Pin Asserting the three-state control (TSC) input causes the MCU to put all output drivers in an inactive, high-impedance state. The signal must remain asserted for ten clock cycles in order for drivers to change state. There are certain constraints on use of TSC during power-on reset: * When the internal clock synthesizer is used (MODCLK held high during reset), synthesizer rampup time affects how long the ten cycles take. Worst case is approximately 20 ms from TSC assertion. * When an external clock signal is applied (MODCLK held low during reset), pins go to high-impedance state as soon after TSC assertion as ten clock pulses have been applied to the EXTAL pin. * When TSC assertion takes effect, internal signals are forced to values that can cause inadvertent mode selection. Once the output drivers change state, the MCU must be powered down and restarted before normal operation can resume. 3.9 Interrupts Interrupt recognition and servicing involve complex interaction between the CPU32L, the SIML, and a device or module requesting interrupt service. MOTOROLA 44 For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. The CPU32L provides seven levels of interrupt priority (1-7), seven automatic interrupt vectors, and 200 assignable interrupt vectors. All interrupts with priorities less than seven can be masked by the interrupt priority (IP) field in status register. The CPU32L handles interrupts as a type of asynchronous expression. There are seven interrupt request signals (IRQ[7:1]). These signals are used internally on the IMB, and there are corresponding pins for external interrupt service requests. The CPU treats all interrupt requests as though they come from internal modules -- external interrupt requests are treated as interrupt service requests from the SIML. Each of the interrupt request signals corresponds to an interrupt priority level. IRQ1 has the lowest priority and IRQ7 the highest. Freescale Semiconductor, Inc... Interrupt recognition is determined by interrupt priority level and interrupt priority mask value. The interrupt priority mask consists of three bits in the CPU32L status register. Binary values %000 to %111 provide eight priority masks. Masks prevent an interrupt request of a priority less than or equal to the mask value from being recognized and processed. IRQ7, however, is always recognized, even if the mask value is %111. IRQ[7:1] are active-low level-sensitive inputs. The low on the pin must remain asserted until an interrupt acknowledge cycle corresponding to that level is detected. IRQ7 is transition-sensitive as well as level-sensitive: a level 7 interrupt is not detected unless a falling edge transition is detected on the IRQ7 line. This prevents redundant servicing and stack overflow. A non-maskable interrupt is generated each time IRQ7 is asserted as well as each time the priority mask changes from %111 to a lower number while IRQ7 is asserted. Interrupt requests are sampled on consecutive falling edges of the system clock. Interrupt request input circuitry has hysteresis: to be valid, a request signal must be asserted for at least two consecutive clock periods. Valid requests do not cause immediate exception processing, but are left pending. Pending requests are processed at instruction boundaries or when exception processing of higher-priority exceptions is complete. The CPU32L does not latch the priority of a pending interrupt request. If an interrupt source of higher priority makes a service request while a lower priority request is pending, the higher priority request is serviced. If an interrupt request with a priority equal to or lower than the current IP mask value is made, the CPU32L does not recognize the occurrence of the request. If simultaneous interrupt requests of different priorities are made, and both have a priority greater than the mask value, the CPU32L recognizes the higher-level request. 3.9.1 Interrupt Acknowledge and Arbitration When the CPU32L detects one or more interrupt requests of a priority higher than the interrupt priority mask value, it places the interrupt request level on the address bus and initiates a CPU space read cycle. The request level serves two purposes: it is decoded by modules or external devices that have requested interrupt service, to determine whether the current interrupt acknowledge cycle pertains to them, and it is latched into the interrupt priority mask field in the CPU32L status register, to preclude further interrupts of lower priority during interrupt service. Modules or external devices that have requested interrupt service must decode the interrupt priority mask value placed on the address bus during the interrupt acknowledge cycle and respond if the priority of the service request corresponds to the mask value. However, before modules or external devices respond, interrupt arbitration takes place. MC68CK338 MC68CK338TS/D For More Information On This Product, Go to: www.freescale.com MOTOROLA 45 Freescale Semiconductor, Inc. Arbitration is performed by means of serial contention between values stored in individual module interrupt arbitration (IARB) fields. Each module that can make an interrupt service request, including the SIML, has an IARB field in its configuration register. IARB fields can be assigned values from %0000 to %1111. In order to implement an arbitration scheme, each module that can initiate an interrupt service request must be assigned a unique, non-zero IARB field value during system initialization. Arbitration priorities range from %0001 (lowest) to %1111 (highest) -- if the CPU recognizes an interrupt service request from a source that has an IARB field value of %0000, a spurious interrupt exception is processed. Freescale Semiconductor, Inc... WARNING Do not assign the same arbitration priority to more than one module. When two or more IARB fields have the same non-zero value, the CPU32L interprets multiple vector numbers at the same time, with unpredictable consequences. Because the EBI manages external interrupt requests, the SIML IARB value is used for arbitration between internal and external interrupt requests. The reset value of IARB for the SIML is %1111, and the reset IARB value for all other modules is %0000. Although arbitration is intended to deal with simultaneous requests of the same priority, it always takes place, even when a single source is requesting service. This is important for two reasons: the EBI does not transfer the interrupt acknowledge read cycle to the external bus unless the SIML wins contention, and failure to contend causes the interrupt acknowledge bus cycle to be terminated early, by a bus error. When arbitration is complete, the module with the highest arbitration priority must terminate the bus cycle. Internal modules place an interrupt vector number on the data bus and generate appropriate internal cycle termination signals. In the case of an external interrupt request, after the interrupt acknowledge cycle is transferred to the external bus, the appropriate external device must decode the mask value and respond with a vector number, then generate data and size acknowledge (DSACK) termination signals, or it must assert the autovector (AVEC) request signal. If the device does not respond in time, the EBI bus monitor asserts the bus error signal (BERR), and a spurious interrupt exception is taken. Chip-select logic can also be used to generate internal AVEC or DSACK signals in response to interrupt requests from external devices. Chip-select address match logic functions only after the EBI transfers an interrupt acknowledge cycle to the external bus following IARB contention. If a module makes an interrupt request of a certain priority, and the appropriate chip-select registers are programmed to generate AVEC or DSACK signals in response to an interrupt acknowledge cycle for that priority level, chipselect logic does not respond to the interrupt acknowledge cycle, and the internal module supplies a vector number and generates internal cycle termination signals. For periodic timer interrupts, the PIRQL field in the periodic interrupt control register (PICR) determines PIT priority level. A PIRQL value of %000 means that PIT interrupts are inactive. By hardware convention, when the CPU32L receives simultaneous interrupt requests of the same level from more than one SIML source (including external devices), the periodic interrupt timer is given the highest priority, followed by the IRQ pins. Refer to 3.4.6 Periodic Interrupt Timer for more information. 3.9.2 Interrupt Processing Summary A summary of the interrupt processing sequence follows. When the sequence begins, a valid interrupt service request has been detected and is pending. MOTOROLA 46 For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc... Freescale Semiconductor, Inc. A. The CPU finishes higher priority exception processing or reaches an instruction boundary. B. The processor state is stacked. The S bit in the status register is set, establishing supervisor access level, and bits T1 and T0 are cleared, disabling tracing. C. The interrupt acknowledge cycle begins: 1. FC[2:0] are driven to %111 (CPU space) encoding. 2. The address bus is driven as follows: ADDR[23:20] = %1111; ADDR[19:16] = %1111, which indicates that the cycle is an interrupt acknowledge CPU space cycle; ADDR[15:4] = %111111111111; ADDR[3:1] = the priority of the interrupt request being acknowledged; and ADDR0 = %1. 3. The request level is latched from the address bus into the interrupt priority mask field in the status or condition code register. D. Modules that have requested interrupt service decode the priority value on ADDR[3:1]. If request priority is the same as acknowledged priority, arbitration by IARB contention takes place. E. After arbitration, the interrupt acknowledge cycle is completed in one of the following ways: 1. When there is no contention (IARB = %0000), the spurious interrupt monitor asserts BERR, and the CPU generates the spurious interrupt vector number. 2. The dominant interrupt source supplies a vector number and DSACK signals appropriate to the access. The CPU acquires the vector number. 3. The AVEC signal is asserted (the signal can be asserted by the dominant interrupt source or the pin can be tied low), and the CPU generates an autovector number corresponding to interrupt priority. 4. The bus monitor asserts BERR and the CPU32L generates the spurious interrupt vector number. F. The vector number is converted to a vector address. G. The content of the vector address is loaded into the PC, and the processor transfers control to the exception handler routine. 3.10 Factory Test Block The test submodule supports scan-based testing of the various MCU modules. It is integrated into the SIML to support production testing. Test submodule registers are intended for Motorola use. Register names and addresses are provided to indicate that these addresses are occupied. SIMLTR -- System Integration Module Test Register $YFFA02 SIMLTRE -- System Integration Module Test Register (E Clock) $YFFA08 TSTMSRA -- Master Shift Register A $YFFA30 TSTMSRB -- Master Shift Register B $YFFA32 TSTSC -- Test Module Shift Count $YFFA34 TSTRC -- Test Module Repetition Count $YFFA36 CREG -- Test Module Control Register $YFFA38 DREG -- Test Module Distributed Register $YFFA3A MC68CK338 MC68CK338TS/D For More Information On This Product, Go to: www.freescale.com MOTOROLA 47 Freescale Semiconductor, Inc. 4 Low-Power Central Processor Unit Based on the powerful MC68020, the CPU32L processing module provides enhanced system performance and also uses the extensive software base for the Motorola M68000 family. 4.1 Overview Freescale Semiconductor, Inc... The CPU32L is fully object-code compatible with the M68000 family, which excels at processing calculation-intensive algorithms and supporting high-level languages. The CPU32L supports all of the MC68010 and most of the MC68020 enhancements, such as virtual memory support, loop mode operation, instruction pipeline, and 32-bit mathematical operations. Powerful addressing modes provide compatibility with existing software programs and increase the efficiency of high-level language compilers. Special instructions, such as table lookup and interpolate and low-power stop, support the specific requirements of controller applications. Also included is background debug mode, an alternate operating mode that suspends normal operation and allows the CPU to accept debugging commands from the development system. Ease of programming is an important consideration in using a microcontroller. The CPU32L instruction set is optimized for high performance. The eight 32-bit general-purpose data registers readily support 8-bit (byte), 16-bit (word), and 32-bit (long word) operations. Ease of program checking and diagnosis is further enhanced by trace and trap capabilities at the instruction level. Use of high-level languages is increasing as controller applications become more complex and control programs become larger. High-level languages aid rapid development of software, with less error, and are readily portable. The CPU32L instruction set supports high-level languages. 4.2 Programming Model The CPU32L has sixteen 32-bit general registers, a 32-bit program counter, one 32-bit supervisor stack pointer, a 16-bit status register, two alternate function code registers, and a 32-bit vector base register. The programming model of the CPU32L consists of a user model shown in Figure 12 and a supervisor model shown in Figure 13, corresponding to the user and supervisor privilege levels. Some instructions available at the supervisor level are not available at the user level, allowing the supervisor to protect system resources from uncontrolled access. Bit S in the status register determines the privilege level. The user programming model remains unchanged from previous M68000 family microprocessors. Application software written to run at the nonprivileged user level migrates without modification to the CPU32L from any M68000 platform. The move from SR instruction, however, is privileged in the CPU32L. It is not privileged in the M68000. MOTOROLA 48 For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. 31 16 15 87 0 D0 D1 D2 D3 DATA REGISTERS D4 D5 D6 D7 Freescale Semiconductor, Inc... 31 16 15 0 A0 A1 A2 A3 ADDRESS REGISTERS A4 A5 A6 31 16 15 0 31 A7 (SSP) USER STACK POINTER PC PROGRAM COUNTER 0 7 0 CCR CONDITION CODE REGISTER CPU32 USER PROG MODEL Figure 12 User Programming Model MC68CK338 MC68CK338TS/D For More Information On This Product, Go to: www.freescale.com MOTOROLA 49 Freescale Semiconductor, Inc. 31 16 15 0 A7' (SSP) SUPERVISOR STACK POINTER 15 87 0 (CCR) 31 SR STATUS REGISTER VBR VECTOR BASE REGISTER SFC ALTERNATE FUNCTION DFC CODE REGISTERS 0 0 2 Freescale Semiconductor, Inc... CPU32 SUPV PROG MODEL Figure 13 Supervisor Programming Model Supplement 4.3 Status Register The status register contains the condition codes that reflect the results of a previous operation and can be used for conditional instruction execution in a program. The lower byte containing the condition codes is the only portion of the register available at the user privilege level; it is referenced as the condition code register (CCR) in user programs. At the supervisor privilege level, software can access the full status register, including the interrupt priority mask and additional control bits. SR -- Status Register 15 14 13 12 11 T1 T0 S 0 0 1 0 0 10 9 8 IP 7 6 5 4 3 2 1 0 0 0 0 X N Z V C 0 0 0 U U U U U RESET: 0 0 1 1 1 System Byte T[1:0] -- Trace Enable S -- Supervisor/User State Bits [12:11] -- Unimplemented IP[2:0] -- Interrupt Priority Mask User Byte (Condition Code Register) Bits [7:5] -- Unimplemented X -- Extend N -- Negative Z -- Zero V -- Overflow C -- Carry MOTOROLA 50 For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. 4.4 Data Types Six basic data types are supported: * Bits * Packed Binary Coded Decimal Digits * Byte Integers (8 bits) * Word Integers (16 bits) * Long Word Integers (32 bits) * Quad Word Integers (64 bits) 4.5 Addressing Modes Freescale Semiconductor, Inc... Addressing in the CPU32L is register-oriented. Most instructions allow the results of the specified operation to be placed either in a register or directly in memory. This flexibility eliminates the need for extra instructions to store register contents in memory. The CPU32L supports seven basic addressing modes: * Register direct * Register indirect * Register indirect with index * Program counter indirect with displacement * Program counter indirect with index * Absolute * Immediate Included in the register indirect addressing modes are the capabilities to post-increment, predecrement, and offset. The program counter relative mode also has index and offset capabilities. In addition to these addressing modes, many instructions implicitly specify the use of the status register, stack pointer, or program counter. 4.6 Instruction Set Summary Table 33 provides a summary of the CPU32L instruction set. MC68CK338 MC68CK338TS/D For More Information On This Product, Go to: www.freescale.com MOTOROLA 51 Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... Table 33 Instruction Set Summary Instruction Syntax Operand Size Operation ABCD Dn, Dn - (An), - (An) 8 8 ADD Dn, <ea> <ea>, Dn 8, 16, 32 8, 16, 32 Source + Destination Destination ADDA <ea>, An 16, 32 Source + Destination Destination Source10 + Destination10 + X Destination ADDI #<data>, <ea> 8, 16, 32 Immediate data + Destination Destination ADDQ # <data>, <ea> 8, 16, 32 Immediate data + Destination Destination ADDX Dn, Dn - (An), - (An) 8, 16, 32 8, 16, 32 Source + Destination + X Destination AND <ea>, Dn Dn, <ea> 8, 16, 32 8, 16, 32 Source * Destination Destination ANDI # <data>, <ea> 8, 16, 32 Data * Destination Destination # <data>, CCR 8 Source * CCR CCR ANDI to CCR ANDI to SR1 # <data>, SR 16 Source * SR SR ASL Dn, Dn # <data>, Dn <ea> 8, 16, 32 8, 16, 32 16 X/C ASR Dn, Dn # <data>, Dn <ea> 8, 16, 32 8, 16, 32 16 Bcc label 8, 16, 32 BCHG Dn, <ea> # <data>, <ea> 8, 32 8, 32 BCLR Dn, <ea> # <data>, <ea> 8, 32 8, 32 BGND none none If background mode enabled, then enter background mode, else format/vector - (SSP); PC - (SSP); SR - (SSP); (vector) PC BKPT # <data> none If breakpoint cycle acknowledged, then execute returned operation word, else trap as illegal instruction BRA label 8, 16, 32 BSET Dn, <ea> # <data>, <ea> 8, 32 8, 32 BSR label 8, 16, 32 BTST Dn, <ea> # <data>, <ea> 8, 32 8, 32 CHK <ea>, Dn 16, 32 CHK2 <ea>, Rn 8, 16, 32 If Rn < lower bound or Rn > upper bound, then CHK exception CLR <ea> 8, 16, 32 0 Destination CMP <ea>, Dn 8, 16, 32 (Destination - Source), CCR shows results (Destination - Source), CCR shows results 1 CMPA <ea>, An 16, 32 CMPI # <data>, <ea> 8, 16, 32 MOTOROLA 52 0 X/C If condition true, then PC + d PC ( bit number of destination ) Z bit of destination ( bit number of destination ) Z; 0 bit of destination PC + d PC ( bit number of destination ) Z; 1 bit of destination SP - 4 SP; PC (SP); PC + d PC ( bit number of destination ) Z If Dn < 0 or Dn > (ea), then CHK exception (Destination - Data), CCR shows results For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... Table 33 Instruction Set Summary (Continued) Instruction Syntax Operand Size CMPM (An) +, (An) + 8, 16, 32 (Destination - Source), CCR shows results CMP2 <ea>, Rn 8, 16, 32 Lower bound Rn Upper bound, CCR shows result DBcc Dn, label 16 DIVS/DIVU <ea>, Dn 32/16 16 : 16 Destination / Source Destination (signed or unsigned) DIVSL/DIVUL <ea>, Dr : Dq <ea>, Dq <ea>, Dr : Dq 64/32 32 : 32 32/32 32 32/32 32 : 32 Destination / Source Destination (signed or unsigned) EOR Dn, <ea> 8, 16, 32 Source Destination Destination EORI # <data>, <ea> 8, 16, 32 Data Destination Destination # <data>, CCR 8 Source CCR CCR EORI to SR # <data>, SR 16 Source SR SR EXG Rn, Rn 32 Rn Rn EXT Dn Dn 8 16 16 32 Sign extended Destination Destination EXTB Dn 8 32 Sign extended Destination Destination none SSP - 2 SSP; vector offset (SSP); SSP - 4 SSP; PC (SSP); SSP - 2 SSP; SR (SSP); Illegal instruction vector address PC EORI to CCR 1 ILLEGAL none Operation If condition false, then Dn - 1 PC; if Dn (- 1), then PC + d PC JMP <ea> none Destination PC JSR <ea> none SP - 4 SP; PC (SP); destination PC LEA <ea>, An 32 An, # d 16, 32 # <data> 16 LSL Dn, Dn # <data>, Dn <ea> 8, 16, 32 8, 16, 32 16 LSR Dn, Dn #<data>, Dn <ea> 8, 16, 32 8, 16, 32 16 MOVE <ea>, <ea> 8, 16, 32 Source Destination MOVEA <ea>, An 16, 32 32 Source Destination MOVEA1 USP, An An, USP 32 32 USP An An USP MOVE from CCR CCR, <ea> 16 CCR Destination MOVE to CCR <ea>, CCR 16 Source CCR MOVE from SR1 SR, <ea> 16 SR Destination MOVE to SR1 <ea>, SR 16 Source SR MOVE USP1 USP, An An, USP 32 32 USP An An USP MOVEC1 Rc, Rn Rn, Rc 32 32 Rc Rn Rn Rc LINK 1, 2 LPSTOP MC68CK338 MC68CK338TS/D <ea> An SP - 4 SP, An (SP); SP An, SP + d SP Data SR; interrupt mask EBI; STOP X/C 0 For More Information On This Product, Go to: www.freescale.com 0 X/C MOTOROLA 53 Freescale Semiconductor, Inc. Table 33 Instruction Set Summary (Continued) Instruction Syntax Operand Size MOVEM list, <ea> <ea>, list 16, 32 16, 32 32 Dn [31 : 24] (An + d); Dn [23 : 16] (An + d + 2); Dn [15 : 8] (An + d + 4); Dn [7 : 0] (An + d + 6) Dn, (d16, An) MOVEP 16, 32 (An + d) Dn [31 : 24]; (An + d + 2) Dn [23 : 16]; (An + d + 4) Dn [15 : 8]; (An + d + 6) Dn [7 : 0] (d16, An), Dn Freescale Semiconductor, Inc... Operation Listed registers Destination Source Listed registers 8 32 Immediate data Destination MOVEQ #<data>, Dn MOVES1 Rn, <ea> <ea>, Rn 8, 16, 32 MULS/MULU <ea>, Dn <ea>, Dl <ea>, Dh : Dl 16 16 32 32 32 32 32 32 64 Source Destination Destination (signed or unsigned) NBCD <ea> 8 8 0 - Destination10 - X Destination NEG <ea> 8, 16, 32 0 - Destination Destination NEGX <ea> 8, 16, 32 0 - Destination - X Destination NOP none none NOT <ea> 8, 16, 32 Destination Destination OR <ea>, Dn Dn, <ea> 8, 16, 32 8, 16, 32 Source + Destination Destination ORI #<data>, <ea> 8, 16, 32 Data + Destination Destination #<data>, CCR 16 Source + CCR SR ORI to SR #<data>, SR 16 Source ; SR SR PEA <ea> 32 SP - 4 SP; <ea> SP RESET1 none none ROL Dn, Dn #<data>, Dn <ea> 8, 16, 32 8, 16, 32 16 ROR Dn, Dn #<data>, Dn <ea> 8, 16, 32 8, 16, 32 16 ROXL Dn, Dn #<data>, Dn <ea> 8, 16, 32 8, 16, 32 16 ROXR Dn, Dn #<data>, Dn <ea> 8, 16, 32 8, 16, 32 16 RTD #d 16 ORI to CCR 1 Rn Destination using DFC Source using SFC Rn PC + 2 PC Assert RESET line C C C X X C (SP) PC; SP + 4 + d SP RTE1 none none (SP) SR; SP + 2 SP; (SP) PC; SP + 4 SP; Restore stack according to format RTR none none (SP) CCR; SP + 2 SP; (SP) PC; SP + 4 SP RTS none none (SP) PC; SP + 4 SP SBCD Dn, Dn - (An), - (An) 8 8 MOTOROLA 54 Destination10 - Source10 - X Destination For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. Table 33 Instruction Set Summary (Continued) Freescale Semiconductor, Inc... Instruction Syntax Operand Size Operation Scc <ea> 8 If condition true, then destination bits are set to 1; else, destination bits are cleared to 0 STOP1 #<data> 16 Data SR; STOP SUB <ea>, Dn Dn, <ea> 8, 16, 32 Destination - Source Destination Destination - Source Destination SUBA <ea>, An 16, 32 SUBI #<data>, <ea> 8, 16, 32 Destination - Data Destination SUBQ #<data>, <ea> 8, 16, 32 Destination - Data Destination SUBX Dn, Dn - (An), - (An) 8, 16, 32 8, 16, 32 Destination - Source - X Destination SWAP Dn 16 TAS <ea> 8 TBLS/TBLU <ea>, Dn Dym : Dyn, Dn 8, 16, 32 Dyn - Dym Temp (Temp Dn [7 : 0]) Temp (Dym 256) + Temp Dn TBLSN/TBLUN <ea>, Dn Dym : Dyn, Dn 8, 16, 32 Dyn - Dym Temp (Temp Dn [7 : 0]) / 256 Temp Dym + Temp Dn TRAP #<data> none SSP - 2 SSP; format/vector offset (SSP); SSP - 4 SSP; PC (SSP); SR (SSP); vector address PC TRAPcc none #<data> none 16, 32 If cc true, then TRAP exception If V set, then overflow TRAP exception TRAPV none none TST <ea> 8, 16, 32 UNLK An 32 MSW LSW Destination Tested Condition Codes bit 7 of Destination Source - 0, to set condition codes An SP; (SP) An, SP + 4 SP 1. Privileged instruction. 2. Two LPSTOP modes are supported. The first LPSTOP mode is the normal LPSTOP in which the system clock on the chip is stopped, shutting down all IMB modules with the exception of some parts of the SIML and CLKOUT. The second LPSTOP mode causes the system clock to be stopped only at the CPU32L, when the LPSTOP instruction is executed by the CPU32L. As with the normal LPSTOP operation, the CPU32L can be restarted by an interrupt, a trace, or a reset exception. MC68CK338 MC68CK338TS/D For More Information On This Product, Go to: www.freescale.com MOTOROLA 55 Freescale Semiconductor, Inc. 4.7 Background Debugging Mode The background debugger on the CPU32L is implemented in CPU microcode. The background debugging commands are summarized in Table 34. Table 34 Background Debugging Mode Commands Freescale Semiconductor, Inc... Command Mnemonic Description Read D/A Register RDREG/RAREG Read the selected address or data register and return the results through the serial interface. Write D/A Register WDREG/WAREG The data operand is written to the specified address or data register. Read System Register RSREG The specified system control register is read. All registers that can be read in supervisor mode can be read in background mode. Write System Register WSREG The operand data is written into the specified system control register. READ Read the sized data at the memory location specified by the long-word address. The source function code register (SFC) determines the address space accessed. WRITE Write the operand data to the memory location specified by the long-word address. The destination function code (DFC) register determines the address space accessed. DUMP Used in conjunction with the READ command to dump large blocks of memory. An initial READ is executed to set up the starting address of the block and retrieve the first result. Subsequent operands are retrieved with the DUMP command. Fill Memory Block FILL Used in conjunction with the WRITE command to fill large blocks of memory. Initially, a WRITE is executed to set up the starting address of the block and supply the first operand. The FILL command writes subsequent operands. Resume Execution GO The pipe is flushed and refilled before resuming instruction execution at the current PC. Patch User Code CALL Current program counter is stacked at the location of the current stack pointer. Instruction execution begins at user patch code. Reset Peripherals RST Asserts RESET for 512 clock cycles. The CPU is not reset by this command. Synonymous with the CPU RESET instruction. No Operation NOP NOP performs no operation and can be used as a null command. Read Memory Location Write Memory Location Dump Memory Block MOTOROLA 56 For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. 5 Queued Serial Module The QSM contains two serial interfaces, the queued serial peripheral interface (QSPI) and the serial communication interface (SCI). Figure 14 shows the QSM block diagram. MISO/PQS0 MOSI/PQS1 SCK/PQS2 PCS0/SS/PQS3 PCS1/PQS4 PCS2/PQS5 PCS3/PQS6 INTERFACE LOGIC PORT QS IMB Freescale Semiconductor, Inc... QSPI TXD/PQS7 SCI RXD QSM BLOCK Figure 14 QSM Block Diagram 5.1 Overview The QSPI provides easy peripheral expansion or interprocessor communication through a full-duplex, synchronous, three-line bus: data in, data out, and a serial clock. Four programmable peripheral chipselect pins provide addressability for up to 16 peripheral devices. A self-contained RAM queue allows up to 16 serial transfers of 8 to 16 bits each, or transmission of a 256-bit data stream without CPU intervention. A special wraparound mode supports continuous sampling of a serial peripheral, with automatic QSPI RAM updating, which makes the interface to A/D converters more efficient. The SCI provides a standard non-return to zero (NRZ) mark/space format. It operates in either full- or half-duplex mode. There are separate transmitter and receiver enable bits and dual data buffers. A modulus-type baud rate generator provides rates from 55 to 451 kbaud with a 14.44-MHz system clock. Word length of either eight or nine bits is software selectable. Optional parity generation and detection provide either even or odd parity check capability. Advanced error detection circuitry catches glitches of up to 1/16 of a bit time in duration. Wakeup functions allow the CPU to run uninterrupted until meaningful data is available. Table 35 shows the address map of the QSM. MC68CK338 MC68CK338TS/D For More Information On This Product, Go to: www.freescale.com MOTOROLA 57 Freescale Semiconductor, Inc. 5.2 Address Map The "Access" column in the QSM address map in Table 35 indicates which registers are accessible only at the supervisor privilege level and which can be assigned to either the supervisor or user privilege level, according to the value of the SUPV bit in the QSMCR. Freescale Semiconductor, Inc... Table 35 QSM Address Map Access Address S $YFFC001 15 QSM Module Configuration Register (QSMCR) 8 7 S $YFFC02 QSM Test Register (QTEST) S $YFFC04 S/U $YFFC06 Not Used S/U $YFFC08 SCI Control 0 Register (SCCR0) S/U $YFFC0A SCI Control 1 Register (SCCR1) S/U $YFFC0C SCI Status Register (SCSR) S/U $YFFC0E SCI Data Register (SCDR) S/U $YFFC10 Not Used S/U $YFFC12 Not Used S/U $YFFC14 Not Used PQS Data Register (PORTQS) S/U $YFFC16 PQS Pin Assignment Register (PQSPAR) PQS Data Direction Register (DDRQS) S/U $YFFC18 SPI Control Register 0 (SPCR0) S/U $YFFC1A SPI Control Register 1 (SPCR1) S/U $YFFC1C SPI Control Register 2 (SPCR2) S/U $YFFC1E S/U $YFFC20 - $YFFCFF Not Used S/U $YFFD00 - $YFFD1F Receive RAM (RR[0:F]) S/U $YFFD20 - $YFFD3F Transmit RAM (TR[0:F]) S/U $YFFD40 - $YFFD4F Command RAM (CR[0:F]) QSM Interrupt Level Register (QILR) 0 QSM Interrupt Vector Register (QIVR) SPI Control Register 3 (SPCR3) SPI Status Register (SPSR) NOTES: 1. Y = M111, where M is the logic state of the MM bit in the SIMLCR. MOTOROLA 58 For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. 5.3 Pin Function Table 36 is a summary of the functions of the QSM pins when they are not configured for general-purpose I/O. The QSM data direction register (DDRQS) designates each pin except RXD as an input or output. Table 36 QSM Pin Functions Pin Mode Pin Function MISO Master Serial data input to QSPI Slave Serial data output from QSPI MOSI Master Serial data output from QSPI Slave Serial data input to QSPI SCK Master Clock output from QSPI Slave Clock input to QSPI Master Input: Assertion causes mode fault Output: Selects peripherals Slave Input: Selects the QSPI Master Output: Selects peripherals Slave None Freescale Semiconductor, Inc... QSPI Pins PCS0/SS PCS[3:1] SCI Pins TXD Transmit Serial data output from SCI RXD Receive Serial data input to SCI 5.4 QSM Registers QSM registers are divided into four categories: QSM global registers, QSM pin control registers, QSPI submodule registers, and SCI submodule registers. The QSPI and SCI registers are defined in separate sections below. Writes to unimplemented register bits have no meaning or effect, and reads from unimplemented bits always return a logic zero value. The module mapping bit of the SIML configuration register (SIMLCR) defines the most significant bit (ADDR23) of the address, shown in each register figure as Y (Y = $7 or $F). This bit, concatenated with the rest of the address given, forms the absolute address of each register. Refer to the SIML section of this technical summary for more information about how the state of MM affects the system. 5.4.1 Global Registers The QSM global registers contain system parameters used by both the QSPI and the SCI submodules. These registers contain the bits and fields used to configure the QSM. QSMCR -- QSM Configuration Register $YFFC00 15 14 13 12 11 10 9 8 7 6 5 4 STOP FRZ1 FRZ0 0 0 0 0 0 SUPV 0 0 0 0 0 0 0 0 0 0 0 0 0 3 2 1 0 0 0 IARB RESET: 0 0 0 0 The QSMCR contains parameters for the QSM/CPU/intermodule bus (IMB) interface. MC68CK338 MC68CK338TS/D For More Information On This Product, Go to: www.freescale.com MOTOROLA 59 Freescale Semiconductor, Inc. STOP -- Stop Enable 0 = Normal QSM clock operation 1 = QSM clock operation stopped STOP places the QSM in a low-power state by disabling the system clock in most parts of the module. The QSMCR is the only register guaranteed to be readable while STOP is asserted. The QSPI RAM is not readable. However, writes to RAM or any register are guaranteed to be valid while STOP is asserted. STOP can be negated by the CPU and by reset. Freescale Semiconductor, Inc... The system software must stop each submodule before asserting STOP to avoid complications at restart and to avoid data corruption. The SCI submodule receiver and transmitter should be disabled, and the operation should be verified for completion before asserting STOP. The QSPI submodule should be stopped by asserting the HALT bit in SPCR3 and by asserting STOP after the HALTA flag is set. FRZ1 -- Freeze 1 0 = Ignore the FREEZE signal on the IMB 1 = Halt the QSPI (on a transfer boundary) FRZ1 determines what action is taken by the QSPI when the FREEZE signal of the IMB is asserted. FREEZE is asserted whenever the CPU enters the background mode. FRZ0 -- Freeze 0 Reserved Bits [12:8] -- Not Implemented SUPV -- Supervisor/Unrestricted 0 = User access 1 = Supervisor access SUPV defines the assignable QSM registers as either supervisor-only data space or unrestricted data space. IARB -- Interrupt Arbitration Identification Number The IARB field is used to arbitrate between simultaneous interrupt requests of the same priority. Each module that can generate interrupt requests must be assigned a unique, non-zero IARB field value. Refer to 3.9 Interrupts for more information. QTEST -- QSM Test Register $YFFC02 QTEST is used during factory testing of the QSM. Accesses to QTEST must be made while the MCU is in test mode. QILR -- QSM Interrupt Levels Register 15 14 0 0 13 12 11 10 ILQSPI $YFFC04 9 8 ILSCI 7 6 5 4 3 2 1 0 QIVR RESET: 0 0 0 0 0 0 0 0 QILR determines the priority level of interrupts requested by the QSM and the vector used when an interrupt is acknowledged. ILQSPI -- Interrupt Level for QSPI ILQSPI determines the priority of QSPI interrupts. This field must be given a value between $0 (interrupts disabled) to $7 (highest priority). MOTOROLA 60 For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. ILSCI -- Interrupt Level of SCI ILSCI determines the priority of SCI interrupts. This field must be given a value between $0 (interrupts disabled) to $7 (highest priority). If ILQSPI and ILSCI are the same nonzero value, and both submodules simultaneously request interrupt service, QSPI has priority. QIVR -- QSM Interrupt Vector Register 15 14 13 12 11 10 $YFFC05 9 8 7 6 5 4 QILR 3 2 1 0 1 1 1 1 INTV RESET: Freescale Semiconductor, Inc... 0 0 0 0 At reset, QIVR is initialized to $0F, which corresponds to the uninitialized interrupt vector in the exception table. This vector is selected until QIVR is written. A user-defined vector ($40-$FF) should be written to QIVR during QSM initialization. After initialization, QIVR determines which two vectors in the exception vector table are to be used for QSM interrupts. The QSPI and SCI submodules have separate interrupt vectors adjacent to each other. Both submodules use the same interrupt vector with the least significant bit (LSB) determined by the submodule causing the interrupt. The value of INTV0 used during an interrupt-acknowledge cycle is supplied by the QSM. During an interrupt-acknowledge cycle, INTV[7:1] are driven on DATA[7:1] IMB lines. DATA0 is negated for an SCI interrupt and asserted for a QSPI interrupt. Writes to INTV0 have no meaning or effect. Reads of INTV0 return a value of one. 5.4.2 Pin Control Registers The QSM uses nine pins, eight of which form a parallel port (PORTQS) on the MCU. Although these pins are used by the serial subsystems, any pin can alternately be assigned as general-purpose I/O on a pin-by-pin basis. Pins used for general-purpose I/O must not be assigned to the QSPI by register PQSPAR. To avoid driving incorrect data, the first byte to be output must be written before DDRQS is configured. DDRQS must then be written to determine the direction of data flow and to output the value contained in register PORTQS. Subsequent data for output is written to PORTQS. PORTQS -- Port QS Data Register 15 14 13 12 11 RESERVED 10 $YFFC14 9 8 7 6 5 4 3 2 1 0 PQS7 PQS6 PQS5 PQS4 PQS3 PQS2 PQS1 PQS0 0 0 0 0 0 0 0 0 RESET: PORTQS latches I/O data. Writes drive pins defined as outputs. Reads return data present on the pins. To avoid driving undefined data, first write a byte to PORTQS, then configure DDRQS. MC68CK338 MC68CK338TS/D For More Information On This Product, Go to: www.freescale.com MOTOROLA 61 Freescale Semiconductor, Inc. PQSPAR -- PORT QS Pin Assignment Register DDRQS -- PORT QS Data Direction Register 15 0 14 13 12 11 10 PQSPA6 PQSPA5 PQSPA4 PQSPA3 0 9 $YFFC16 $YFFC17 8 7 6 5 4 3 2 1 0 PQSPA1 PQSPA0 DDQS7 DDQS6 DDQS5 DDQS4 DDQS3 DDQS2 DDQS1 DDQS0 RESET: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Clearing a bit in the PQSPAR assigns the corresponding pin to general-purpose I/O; setting a bit assigns the pin to the QSPI. The PQSPAR does not affect operation of the SCI. Table 37 displays PQSPAR pin assignments. Freescale Semiconductor, Inc... Table 37 PQSPAR Pin Assignments PQSPAR Field PQSPAR Bit Pin Function PQSPA0 0 PQS0 1 MISO 0 PQS1 PQSPA1 PQSPA2 PQSPA3 PQSPA4 PQSPA5 PQSPA6 PQSPA7 1 MOSI 0 PQS21 1 SCK 0 PQS3 1 PCS0/SS 0 PQS4 1 PCS1 0 PQS5 1 PCS2 0 PQS6 1 PCS3 0 PQS72 1 TXD NOTES: 1. PQS2 is a digital I/O pin unless the SPI is enabled (SPE in SPCR1 set), in which case it becomes SPI serial clock SCK. 2. PQS7 is a digital I/O pin unless the SCI transmitter is enabled (TE in SCCR1 = 1), in which case it becomes SCI serial output TXD. DDRQS determines whether pins are inputs or outputs. Clearing a bit makes the corresponding pin an input; setting a bit makes the pin an output. DDRQS affects both QSPI function and I/O function. Table 38 shows the effect of DDRQS on QSM pin functions. MOTOROLA 62 For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. Table 38 Effect of DDRQS on QSM Pin Function QSM Pin Mode DDRQS Bit Bit State Pin Function MISO Master DDQ0 0 Serial data input to QSPI Slave MOSI Master DDQ1 Slave 1 Freescale Semiconductor, Inc... SCK Master DDQ2 Slave PCS0/SS Master DDQ3 Slave PCS[3:1] Master DDQ[4:6] Slave 1 Disables data input 0 Disables data output 1 Serial data output from QSPI 0 Disables data output 1 Serial data output from QSPI 0 Serial data input to QSPI 1 Disables data input 0 Disables clock output 1 Clock output from QSPI 0 Clock input to QSPI 1 Disables clock Input 0 Assertion causes mode fault 1 Chip-select output 0 QSPI slave select input 1 Disables select input 0 Disables chip-select output 1 Chip-select output 0 Inactive 1 Inactive 2 TXD Transmit DDQ7 X Serial data output from SCI RXD Receive None NA Serial data input to SCI NOTES: 1. PQS2 is a digital I/O pin unless the SPI is enabled (SPE in SPCR1 set), in which case it becomes SPI serial clock SCK. 2. PQS7 is a digital I/O pin unless the SCI transmitter is enabled (TE in SCCR1 = 1), in which case it becomes SCI serial output TXD. DDRQS determines the direction of the TXD pin only when the SCI transmitter is disabled. When the SCI transmitter is enabled, the TXD pin is an output. MC68CK338 MC68CK338TS/D For More Information On This Product, Go to: www.freescale.com MOTOROLA 63 Freescale Semiconductor, Inc. 5.5 QSPI Submodule The QSPI submodule communicates with external devices through a synchronous serial bus. The QSPI is fully compatible with the serial peripheral interface (SPI) systems found on other Motorola products. Figure 15 shows a block diagram of the QSPI. QUEUE CONTROL BLOCK QUEUE POINTER Freescale Semiconductor, Inc... COMPARATOR 4 A D D R E S S DONE 4 END QUEUE POINTER 80-BYTE QSPI RAM R E G I S T E R CONTROL LOGIC STATUS REGISTER CONTROL REGISTERS 4 DELAY COUNTER CHIP SELECT 4 COMMAND MSB M S LSB 8/16-BIT SHIFT REGISTER PROGRAMMABLE LOGIC ARRAY MOSI Rx/Tx DATA REGISTER M S MISO PCS0/SS 2 PCS[2:1] BAUD RATE GENERATOR SCK QSPI BLOCK Figure 15 QSPI Block Diagram MOTOROLA 64 For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. 5.5.1 QSPI Pins Seven pins are associated with the QSPI. When not needed for a QSPI function, they can be configured as general-purpose I/O pins. The PCS0/SS pin can function as a peripheral chip select output, slave select input, or general-purpose I/O. Refer to Table 39 for QSPI input and output pins and their functions. Table 39 QSPI Pins Freescale Semiconductor, Inc... Pin Name(s) Mnemonic(s) Mode Function Master In Slave Out MISO Master Slave Serial data input to QSPI Serial data output from QSPI Master Out Slave In MOSI Master Slave Serial data output from QSPI Serial data input to QSPI Serial Clock SCK Master Slave Clock output from QSPI Clock input to QSPI Peripheral Chip Selects PCS[3:1] Master Select peripherals Peripheral Chip Select Slave Select PCS0 SS Master Master Slave Selects peripheral Causes mode fault Initiates serial transfer 5.5.2 QSPI Registers The programmer's model for the QSPI submodule consists of the QSM global and pin control registers, four QSPI control registers, one status register, and the 80-byte QSPI RAM. The CPU can read and write to registers and RAM. The four control registers must be initialized before the QSPI is enabled to ensure defined operation. SPCR1 should be written last because it contains QSPI enable bit SPE. Asserting this bit starts the QSPI. The QSPI control registers are reset to a defined state and can then be changed by the CPU. Reset values are shown below each register. Table 40 shows a memory map of the QSPI. Table 40 QSPI Memory Map Address Name Usage $YFFC18 SPCR0 QSPI control register 0 $YFFC1A SPCR1 QSPI control register 1 $YFFC1C SPCR2 QSPI control register 2 $YFFC1E SPCR3 QSPI control register 3 $YFFC1F SPSR QSPI status register $YFFD00 RR[0:F] QSPI receive data (16 words) $YFFD20 TR[0:F] QSPI transmit data (16 words) $YFFD40 CR[0:F] QSPI command control (8 words) Writing a different value into any control register except SPCR2 while the QSPI is enabled disrupts operation. SPCR2 is buffered to prevent disruption of the current serial transfer. After completion of the current serial transfer, the new SPCR2 values become effective. Writing the same value into any control register except SPCR2 while the QSPI is enabled has no effect on QSPI operation. Rewriting NEWQP[3:0] in SPCR2 causes execution to restart at the designated location. MC68CK338 MC68CK338TS/D For More Information On This Product, Go to: www.freescale.com MOTOROLA 65 Freescale Semiconductor, Inc. SPCR0 -- QSPI Control Register 0 15 14 MSTR WOMQ 13 12 11 $YFFC18 10 BITS[3:0] 9 8 CPOL CPHA 0 1 7 6 5 4 3 2 1 0 1 0 0 SPBR[7:0] RESET: 0 0 0 0 0 0 0 0 0 0 0 SPCR0 contains parameters for configuring the QSPI before it is enabled. The CPU can read and write this register. The QSM has read-only access. Freescale Semiconductor, Inc... MSTR -- Master/Slave Mode Select 0 = QSPI is a slave device and only responds to externally generated serial data. 1 = QSPI is system master and can initiate transmission to external SPI devices. MSTR configures the QSPI for either master or slave mode operation. This bit is cleared on reset and may only be written by the CPU. WOMQ -- Wired-OR Mode for QSPI Pins 0 = Outputs have normal MOS drivers. 1 = Pins designated for output by DDRQS have open-drain drivers. WOMQ allows the wired-OR function to be used on QSPI pins, regardless of whether they are used as general-purpose outputs or as QSPI outputs. WOMQ affects the QSPI pins regardless of whether the QSPI is enabled or disabled. BITS[3:0] -- Bits Per Transfer In master mode, when BITSE in a command is set, the BITS[3:0] field determines the number of data bits transferred. When BITSE is cleared, eight bits are transferred. Reserved values default to eight bits. In slave mode, the command RAM is not used and the setting of BITSE has no effect on QSPI transfers. Instead, the BITS[3:0] field determines the number of bits the QSPI will receive during each transfer before storing the received data. Table 41 shows the number of bits per transfer. Table 41 Bits Per Transfer MOTOROLA 66 BITS[3:0] Bits Per Transfer 0000 16 0001 Reserved 0010 Reserved 0011 Reserved 0100 Reserved 0101 Reserved 0110 Reserved 0111 Reserved 1000 8 1001 9 1010 10 1011 11 1100 12 1101 13 1110 14 1111 15 For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. CPOL -- Clock Polarity 0 = The inactive state value of SCK is logic level zero. 1 = The inactive state value of SCK is logic level one. CPOL is used to determine the inactive state value of the serial clock (SCK). It is used with CPHA to produce a desired clock/data relationship between master and slave devices. Freescale Semiconductor, Inc... CPHA -- Clock Phase 0 = Data is captured on the leading edge of SCK and changed on the following edge of SCK. 1 = Data is changed on the leading edge of SCK and captured on the following edge of SCK. CPHA determines which edge of SCK causes data to change and which edge causes data to be captured. CPHA is used with CPOL to produce a desired clock/data relationship between master and slave devices. CPHA is set at reset. SPBR[7:0] -- Serial Clock Baud Rate The QSPI uses a modulus counter to derive SCK baud rate from the MCU system clock. Baud rate is selected by writing a value from 2 to 255 into the SPBR[7:0] field. The following equation determines the SCK baud rate: System Clock SCK Baud Rate = ------------------------------------2 x SPBR[7:0] or System Clock SPBR[7:0] = -------------------------------------------------------------------------2 x SCK Baud Rate Desired Giving SPBR[7:0] a value of zero or one disables the baud rate generator. SCK is disabled and assumes its inactive state value. No serial transfers occur. At reset, baud rate is initialized to one eighth of the system clock frequency. SPRC1 -- QSPI Control Register 1 15 14 13 12 SPE 11 $YFFC1A 10 9 8 7 6 5 4 DSCKL[6:0] 3 2 1 0 0 1 0 0 DTL[7:0] RESET: 0 0 0 0 0 1 0 0 0 0 0 0 SPCR1 contains parameters for configuring the QSPI before it is enabled. The CPU can read and write this register, but the QSM has read access only, except for SPE, which is automatically cleared by the QSPI after completing all serial transfers, or when a mode fault occurs. SPE -- QSPI Enable 0 = QSPI is disabled. QSPI pins can be used for general-purpose I/O. 1 = QSPI is enabled. Pins allocated by PQSPAR are controlled by the QSPI. DSCKL[6:0] -- Delay before SCK When the DSCK bit in command RAM is set, this field determines the length of delay from PCS valid to SCK transition. PCS can be any of the four peripheral chip-select pins. The following equation determines the actual delay before SCK: DSCKL[6:0] PCS to SCK Delay = -----------------------------------System Clock where DSCKL[6:0] equals {1, 2, 3,..., 127}. When the DSCK value of a queue entry equals zero, then DSCKL[6:0] is not used. Instead, the PCS valid-to-SCK transition is one-half SCK period. MC68CK338 MC68CK338TS/D For More Information On This Product, Go to: www.freescale.com MOTOROLA 67 Freescale Semiconductor, Inc. DTL[7:0] -- Length of Delay after Transfer When the DT bit in command RAM is set, this field determines the length of delay after serial transfer. The following equation is used to calculate the delay: 32 x DTL[7:0] Delay after Transfer = -----------------------------------System Clock where DTL equals {1, 2, 3,..., 255}. A zero value for DTL[7:0] causes a delay-after-transfer value of 8192/System Clock. If DT equals zero, a standard delay is inserted. 17 Standard Delay after Transfer = -----------------------------------System Clock Freescale Semiconductor, Inc... Delay after transfer can be used to provide a peripheral deselect interval. A delay can also be inserted between consecutive transfers to allow serial A/D converters to complete conversion. SPCR2 -- QSPI Control Register 2 15 14 13 12 SPIFIE WREN WRTO 0 0 0 11 $YFFC1C 10 9 8 ENDQP[3:0] 7 6 5 4 0 0 0 0 0 0 0 0 3 2 1 0 NEWQP[3:0] RESET: 0 0 0 0 0 0 0 0 0 0 SPCR2 contains QSPI configuration parameters. The CPU can read and write this register; the QSM has read access only. Writes to SPCR2 are buffered. A write to SPCR2 that changes a bit value while the QSPI is operating is ineffective on the current serial transfer, but becomes effective on the next serial transfer. Reads of SPCR2 return the current value of the register, not of the buffer. SPIFIE -- SPI Finished Interrupt Enable 0 = QSPI interrupts disabled 1 = QSPI interrupts enabled SPIFIE enables the QSPI to generate a CPU interrupt upon assertion of the status flag SPIF. WREN -- Wrap Enable 0 = Wraparound mode disabled 1 = Wraparound mode enabled WREN enables or disables wraparound mode. WRTO -- Wrap To When wraparound mode is enabled, after the end of queue has been reached, WRTO determines which address the QSPI executes. Bit 12 -- Not Implemented ENDQP[3:0] -- Ending Queue Pointer This field contains the last QSPI queue address. Bits [7:4] -- Not Implemented NEWQP[3:0] -- New Queue Pointer Value This field contains the first QSPI queue address. MOTOROLA 68 For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. SPCR3 -- QSPI Control Register $YFFC1E 15 14 13 12 11 10 9 8 0 0 0 0 0 LOOPQ HMIE HALT 0 0 0 0 0 0 0 7 6 5 4 3 2 1 0 SPSR RESET: 0 SPCR3 contains QSPI configuration parameters. The CPU can read and write SPCR3, but the QSM has read-only access. Bits [15:11] -- Not Implemented Freescale Semiconductor, Inc... LOOPQ -- QSPI Loop Mode 0 = Feedback path disabled 1 = Feedback path enabled LOOPQ controls feedback on the data serializer for testing. HMIE -- HALTA and MODF Interrupt Enable 0 = HALTA and MODF interrupts disabled 1 = HALTA and MODF interrupts enabled HMIE controls CPU interrupts caused by the HALTA status flag or the MODF status flag in SPSR. HALT -- Halt 0 = Halt not enabled 1 = Halt enabled When HALT is asserted, the QSPI stops on a queue boundary. It is in a defined state from which it can later be restarted. SPSR -- QSPI Status Register 15 14 13 12 11 SPCR3 $YFFC1F 10 9 8 7 6 5 4 SPIF MODF HALTA 0 0 0 0 0 3 2 1 0 CPTQP[3:0] RESET: 0 0 0 0 SPSR contains QSPI status information. Only the QSPI can assert the bits in this register. The CPU reads this register to obtain status information and writes it to clear status flags. SPIF -- QSPI Finished Flag 0 = QSPI not finished 1 = QSPI finished SPIF is set after execution of the command at the address in ENDQP[3:0]. MODF -- Mode Fault Flag 0 = Normal operation 1 = Another SPI node requested to become the network SPI master while the QSPI was enabled in master mode (SS input taken low). The QSPI asserts MODF when the QSPI is the serial master (MSTR = 1) and the SS input pin is negated by an external driver. HALTA -- Halt Acknowledge Flag 0 = QSPI not halted 1 = QSPI halted HALTA is asserted when the QSPI halts in response to CPU assertion of HALT. Bit 4 -- Not Implemented MC68CK338 MC68CK338TS/D For More Information On This Product, Go to: www.freescale.com MOTOROLA 69 Freescale Semiconductor, Inc. CPTQP[3:0] -- Completed Queue Pointer CPTQP[3:0] points to the last command executed. It is updated when the current command is complete. When the first command in a queue is executing, CPTQP[3:0] contains either the reset value ($0) or a pointer to the last command completed in the previous queue. 5.5.3 QSPI RAM The QSPI contains an 80-byte block of dual-access static RAM that is used by both the QSPI and the CPU. The RAM is divided into three segments: receive data, transmit data, and command control data. Receive data is information received from a serial device external to the MCU. Transmit data is information stored by the CPU for transmission to an external peripheral. Command control data is used to perform the transfer. Freescale Semiconductor, Inc... Figure 16 displays the organization of the RAM. 500 51E RR0 RR1 RR2 520 TR0 TR1 TR2 540 CR0 CR1 CR2 RECEIVE RAM TRANSMIT RAM COMMAND RAM RRD RRE RRF TRD TRE TRF CRD CRE CRF WORD 53E WORD 54F BYTE QSPI RAM MAP Figure 16 QSPI RAM Once the CPU has set up the queue of QSPI commands and enabled the QSPI, the QSPI can operate independently of the CPU. The QSPI executes all of the commands in its queue, sets a flag indicating that it is finished, and then either interrupts the CPU or waits for CPU intervention. It is possible to execute a queue of commands repeatedly without CPU intervention. RR[0:F] -- Receive Data RAM $YFFD00 Data received by the QSPI is stored in this segment. The CPU reads this segment to retrieve data from the QSPI. Data stored in receive RAM is right-justified. Unused bits in a receive queue entry are set to zero by the QSPI upon completion of the individual queue entry. The CPU can access the data using byte, word, or long-word addressing. The CPTQP[3:0] value in SPSR shows which queue entries have been executed. The CPU uses this information to determine which locations in receive RAM contain valid data before reading them. TR[0:F] -- Transmit Data RAM $YFFD20 Data that is to be transmitted by the QSPI is stored in this segment. The CPU usually writes one word of data into this segment for each queue command to be executed. MOTOROLA 70 For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. Information to be transmitted must be written to transmit data RAM in a right-justified format. The QSPI cannot modify information in the transmit data RAM. The QSPI copies the information to its data serializer for transmission. Information remains in transmit RAM until overwritten. Freescale Semiconductor, Inc... CR[0:F] -- Command RAM $YFFD40 7 6 5 4 3 2 1 0 CONT BITSE DT DSCK PCS3 PCS2 PCS1 PCS01 - - - - - - - - CONT BITSE DT DSCK PCS3 PCS2 PCS1 PCS01 COMMAND CONTROL PERIPHERAL CHIP SELECT NOTES: 1. The PCS0 bit represents the dual-function PCS0/SS. Command RAM is used by the QSPI when in master mode. The CPU writes one byte of control information to this segment for each QSPI command to be executed. The QSPI cannot modify information in command RAM. Command RAM consists of 16 bytes. Each byte is divided into two fields. The peripheral chip-select field enables peripherals for transfer. The command control field provides transfer options. A maximum of 16 commands can be in the queue. Queue execution by the QSPI proceeds from the address in NEWQP[3:0] through the address in ENDQP[3:0]. (Both of these fields are in SPCR2). CONT -- Continue 0 = Control of chip selects returned to PORTQS after transfer is complete. 1 = Peripheral chip selects remain asserted after transfer is complete. BITSE -- Bits per Transfer Enable 0 = 8 bits 1 = Number of bits set in BITS[3:0] field of SPCR0 DT -- Delay after Transfer The QSPI provides a variable delay at the end of serial transfer to facilitate the interface with peripherals that have a latency requirement. The delay between transfers is determined by the SPCR1 DTL[6:0] field. DSCK -- PCS to SCK Delay 0 = PCS valid to SCK transition is one-half SCK. 1 = SPCR1 DSCKL[6:0] field specifies delay from PCS valid to SCK. PCS[3:0] -- Peripheral Chip Select Use peripheral chip-select bits to select an external device for serial data transfer. More than one peripheral chip select can be activated at a time, and more than one peripheral chip can be connected to each PCS pin, provided that proper fanout is observed. MC68CK338 MC68CK338TS/D For More Information On This Product, Go to: www.freescale.com MOTOROLA 71 Freescale Semiconductor, Inc. 5.5.4 Operating Modes The QSPI operates in either master or slave mode. Master mode is used when the MCU originates data transfers. Slave mode is used when an external device initiates serial transfers to the MCU through the QSPI. Switching between the modes is controlled by MSTR in SPCR0. Before entering either mode, appropriate QSM and QSPI registers must be properly initialized. In master mode, the QSPI executes a queue of commands defined by control bits in each command RAM queue entry. Chip-select pins are activated, data is transmitted from transmit RAM and received into receive RAM. Freescale Semiconductor, Inc... In slave mode, operation proceeds in response to SS pin activation by an external bus master. Operation is similar to master mode, but no peripheral chip selects are generated, and the number of bits transferred is controlled in a different manner. When the QSPI is selected, it automatically executes the next queue transfer to exchange data with the external device correctly. Although the QSPI inherently supports multi-master operation, no special arbitration mechanism is provided. A mode fault flag (MODF) indicates a request for SPI master arbitration. System software must provide arbitration. Note that unlike previous SPI systems, MSTR is not cleared by a mode fault being set, nor are the QSPI pin output drivers disabled. The QSPI and associated output drivers must be disabled by clearing SPE in SPCR1. 5.6 SCI Submodule The SCI submodule is used to communicate with external devices through an asynchronous serial bus. The SCI is fully compatible with the SCI systems found on other Motorola MCUs, such as the M68HC11 and M68HC05 Families. 5.6.1 SCI Pins There are two unidirectional pins associated with the SCI. The SCI controls the transmit data (TXD) pin when enabled, whereas the receive data (RXD) pin remains a dedicated input pin to the SCI. TXD is available as a general-purpose I/O pin when the SCI transmitter is disabled. When used for I/O, TXD can be configured either as input or output, as determined by QSM register DDRQS. Table 42 shows SCI pins and their functions. Table 42 SCI Pins Pin Names Mnemonics Mode Function Receive data RXD Receiver disabled Receiver enabled Not used Serial data input to SCI Transmit data TXD Transmitter disabled Transmitter enabled General-purpose I/O Serial data output from SCI 5.6.2 SCI Registers The SCI programming model includes QSM global and pin control registers, and four SCI registers. There are two SCI control registers, one status register, and one data register. All registers can be read or written at any time by the CPU. Changing the value of SCI control bits during a transfer operation may disrupt operation. Before changing register values, allow the transmitter to complete the current transfer, then disable the receiver and transmitter. Status flags in the SCSR may be cleared at any time. MOTOROLA 72 For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. SCCR0 -- SCI Control Register 0 15 14 13 0 0 0 0 0 12 $YFFC08 11 10 9 8 7 6 5 4 3 2 1 0 0 0 0 1 0 0 SCBR[12:0] RESET: 0 0 0 0 0 0 0 0 SCCR0 contains a baud rate selection parameter. Baud rate must be set before the SCI is enabled. The CPU can read and write this register at any time. Bits [15:13] -- Not Implemented Freescale Semiconductor, Inc... SCBR[12:0] -- Baud Rate SCI baud rate is programmed by writing a 13-bit value to BR. The baud rate is derived from the MCU system clock by a modulus counter. The SCI receiver operates asynchronously. An internal clock is necessary to synchronize with an incoming data stream. The SCI baud rate generator produces a receiver sampling clock with a frequency 16 times that of the expected baud rate of the incoming data. The SCI determines the position of bit boundaries from transitions within the received waveform, and adjusts sampling points to the proper positions within the bit period. Receiver sampling rate is always 16 times the frequency of the SCI baud rate, which is calculated as follows: System Clock SCI Baud Rate = -----------------------------------------------( 32 ) ( SCBR[12:0] ) or System Clock SCBR[12:0] = --------------------------------------------------------------------------32 x SCI Baud Rate Desired where SCBR[12:0] is in the range {1, 2, 3, ..., 8191} Writing a value of zero to SCBR[12:0] disables the baud rate generator. Table 43 lists the SCBR[12:0] settings for standard and maximum baud rates using a 14.44 MHz system clock. Table 43 SCI Baud Rates Nominal Baud Rate MC68CK338 MC68CK338TS/D Actual Rate with 14.44 MHz Clock SCBR[12:0] Value 64 64.0 $1B8B 110 110.0 $1006 300 300.0 $05E0 600 600.1 $02F0 1200 1200.1 $0178 2400 2400.3 $00BC 4800 4800.5 $005E 9600 9601.1 $002F 19200 18802.1 $0018 38400 37604.2 $000C 76800 75208.3 $0006 Maximum rate 451250.0 $0001 For More Information On This Product, Go to: www.freescale.com MOTOROLA 73 Freescale Semiconductor, Inc. SCCR1 -- SCI Control Register 1 15 0 14 13 LOOPS WOMS $YFFC0A 12 11 10 9 8 7 6 5 4 3 2 1 0 ILT PT PE M WAKE TIE TCIE RIE ILIE TE RE RWU SBK 0 0 0 0 0 0 0 0 0 0 0 0 0 RESET: 0 0 0 SCCR1 contains SCI configuration parameters. The CPU can read and write this register at any time. The SCI can modify RWU in some circumstances. In general, interrupts enabled by these control bits are cleared by reading SCSR, then reading (for receiver status bits) or writing (for transmitter status bits) SCDR. Freescale Semiconductor, Inc... Bit 15 -- Not Implemented LOOPS -- Loop Mode 0 = Normal SCI operation, no looping, feedback path disabled 1 = Test SCI operation, looping, feedback path enabled LOOPS controls a feedback path on the data serial shifter. When loop mode is enabled, SCI transmitter output is fed back into the receive serial shifter. TXD is asserted (idle line). Both transmitter and receiver must be enabled before entering loop mode. WOMS -- Wired-OR Mode for SCI Pins 0 = If configured as an output, TXD is a normal CMOS output. 1 = If configured as an output, TXD is an open-drain output. WOMS determines whether the TXD pin is an open-drain output or a normal CMOS output. This bit is used only when TXD is an output. If TXD is used as a general-purpose input pin, WOMS has no effect. ILT -- Idle-Line Detect Type 0 = Short idle-line detect (start count on first one) 1 = Long idle-line detect (start count on first one after stop bit(s)) PT -- Parity Type 0 = Even parity 1 = Odd parity When parity is enabled, PT determines whether parity is even or odd for both the receiver and the transmitter. PE -- Parity Enable 0 = SCI parity disabled 1 = SCI parity enabled PE determines whether parity is enabled or disabled for both the receiver and the transmitter. If the received parity bit is not correct, the SCI sets the PF error flag in SCSR. When PE is set, the most significant bit (MSB) of the data field is used for the parity function, which results in either seven or eight bits of user data, depending on the condition of M bit. Table 44 lists the available choices. Table 44 Parity Enable Data Bit Selection MOTOROLA 74 M PE Result 0 0 8 data bits 0 1 7 data bits, 1 parity bit 1 0 9 data bits 1 1 8 data bits, 1 parity bit For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. M -- Mode Select 0 = SCI frame: one start bit, eight data bits, one stop bit (10 bits total) 1 = SCI frame: one start bit, nine data bits, one stop bit (11 bits total) WAKE -- Wakeup by Address Mark 0 = SCI receiver awakened by idle-line detection 1 = SCI receiver awakened by address mark (last bit set) TIE -- Transmit Interrupt Enable 0 = SCI TDRE interrupts inhibited 1 = SCI TDRE interrupts enabled Freescale Semiconductor, Inc... TCIE -- Transmit Complete Interrupt Enable 0 = SCI TC interrupts inhibited 1 = SCI TC interrupts enabled RIE -- Receiver Interrupt Enable 0 = SCI RDRF interrupt inhibited 1 = SCI RDRF interrupt enabled ILIE -- Idle-Line Interrupt Enable 0 = SCI IDLE interrupts inhibited 1 = SCI IDLE interrupts enabled TE -- Transmitter Enable 0 = SCI transmitter disabled (TXD pin may be used as I/O) 1 = SCI transmitter enabled (TXD pin dedicated to SCI transmitter) The transmitter retains control of the TXD pin until completion of any character transfer that was in progress when TE is cleared. RE -- Receiver Enable 0 = SCI receiver disabled (status bits inhibited) 1 = SCI receiver enabled RWU -- Receiver Wakeup 0 = Normal receiver operation (received data recognized) 1 = Wakeup mode enabled (received data ignored until awakened) Setting RWU enables the wakeup function, which allows the SCI to ignore received data until awakened by either an idle line or address mark (as determined by WAKE). When in wakeup mode, the receiver status flags are not set, and interrupts are inhibited. This bit is cleared automatically (returned to normal mode) when the receiver is awakened. SBK -- Send Break 0 = Normal operation 1 = Break frame(s) transmitted after completion of current frame SBK provides the ability to transmit a break code from the SCI. If the SCI is transmitting when SBK is set, it will transmit continuous frames of zeros after it completes the current frame, until SBK is cleared. If SBK is toggled (one to zero in less than one frame interval), the transmitter sends only one or two break frames before reverting to idle line or beginning to send data. SCSR -- SCI Status Register 15 14 13 12 NOT USED $YFFC0C 11 10 9 8 7 6 5 4 3 2 1 0 TDRE TC RDRF RAF IDLE OR NF FE PF 1 1 0 0 0 0 0 0 0 RESET: MC68CK338 MC68CK338TS/D For More Information On This Product, Go to: www.freescale.com MOTOROLA 75 Freescale Semiconductor, Inc. SCSR contains flags that show SCI operational conditions. These flags can be cleared either by hardware or by a special acknowledgment sequence. The sequence consists of SCSR read with flags set, followed by SCDR read (write in the case of TDRE and TC). A long-word read can consecutively access both SCSR and SCDR. This action clears receive status flag bits that were set at the time of the read, but does not clear TDRE or TC flags. If an internal SCI signal for setting a status bit comes after the CPU has read the asserted status bits, but before the CPU has written or read register SCDR, the newly set status bit is not cleared. SCSR must be read again with the bit set. Also, SCDR must be written or read before the status bit is cleared. Freescale Semiconductor, Inc... Reading either byte of SCSR causes all 16 bits to be accessed. Any status bit already set in either byte will be cleared on a subsequent read or write of register SCDR. TDRE -- Transmit Data Register Empty Flag 0 = Register TDR still contains data to be sent to the transmit serial shifter. 1 = A new character can now be written to the transmit data register. TDRE is set when the byte in the transmit data register is transferred to the transmit serial shifter. If TDRE is zero, transfer has not occurred and a write to the transmit data register will overwrite the previous value. New data is not transmitted if the transmit data register is written without first clearing TDRE. TC -- Transmit Complete Flag 0 = SCI transmitter is busy 1 = SCI transmitter is idle TC is set when the transmitter finishes shifting out all data, queued preambles (mark/idle line), or queued breaks (logic zero). The interrupt can be cleared by reading SCSR when TC is set and then by writing the transmit data register of SCDR. RDRF -- Receive Data Register Full Flag 0 = Receive data register is empty or contains previously read data. 1 = Receive data register contains new data. RDRF is set when the content of the receive serial shifter is transferred to the receive data register. If one or more errors are detected in the received word, flag(s) NF, FE, and/or PF are set within the same clock cycle. RAF -- Receiver Active Flag 0 = SCI receiver is idle 1 = SCI receiver is busy RAF indicates whether the SCI receiver is busy. It is set when the receiver detects a possible start bit and is cleared when the chosen type of idle line is detected. RAF can be used to reduce collisions in systems with multiple masters. IDLE -- Idle-Line Detected Flag 0 = SCI receiver did not detect an idle-line condition. 1 = SCI receiver detected an idle-line condition. IDLE is disabled when RWU in SCCR1 is set. IDLE is set when the SCI receiver detects the idle-line condition specified by ILT in SCCR1. If cleared, IDLE will not set again until after RDRF is set. RDRF is set when a break is received, so that a subsequent idle line can be detected. OR -- Overrun Error Flag 0 = RDRF is cleared before new data arrives. 1 = RDRF is not cleared before new data arrives. OR is set when a new byte is ready to be transferred from the receive serial shifter to the receive data register, and RDRF is still set. Data transfer is inhibited until OR is cleared. Previous data in receive data register remains valid, but data received during overrun condition (including the byte that set OR) is lost. MOTOROLA 76 For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. NF -- Noise Error Flag 0 = No noise detected on the received data 1 = Noise occurred on the received data NF is set when the SCI receiver detects noise on a valid start bit, on any data bit, or on a stop bit. It is not set by noise on the idle line or on invalid start bits. Each bit is sampled three times. If none of the three samples are the same logic level, the majority value is used for the received data value, and NF is set. NF is not set until an entire frame is received and RDRF is set. Freescale Semiconductor, Inc... FE -- Framing Error Flag 0 = No framing error on the received data. 1 = Framing error or break occurred on the received data. FE is set when the SCI receiver detects a zero where a stop bit was to have occurred. FE is not set until the entire frame is received and RDRF is set. A break can also cause FE to be set. It is possible to miss a framing error if RXD happens to be at logic level one at the time the stop bit is expected. PF -- Parity Error Flag 0 = No parity error on the received data 1 = Parity error occurred on the received data PF is set when the SCI receiver detects a parity error. PF is not set until the entire frame is received and RDRF is set. SCDR -- SCI Data Register $YFFC0E 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 0 0 0 0 0 0 0 R8/T8 R7/T7 R6/T6 R5/T5 R4/T4 R3/T3 R2/T2 R1/T1 R0/T0 0 0 0 0 0 0 U U U U U U U U U RESET: 0 SCDR contains two data registers at the same address. The receive data register is a read-only register that contains data received by the SCI. The data comes into the receive serial shifter and is transferred to the receive data register. The transmit data register is a write-only register that contains data to be transmitted. The data is first written to the transmit data register, then transferred to the transmit serial shifter, where additional format bits are added before transmission. R[7:0]/T[7:0] contain either the first eight data bits received when SCDR is read, or the first eight data bits to be transmitted when SCDR is written. R8/T8 are used when the SCI is configured for 9-bit operation. When it is configured for 8-bit operation, they have no meaning or effect. MC68CK338 MC68CK338TS/D For More Information On This Product, Go to: www.freescale.com MOTOROLA 77 Freescale Semiconductor, Inc. 6 Configurable Timer Module 6 The configurable timer module 6 (CTM6) belongs to a family of timer modules for the Motorola Modular Microcontroller Family. The timer architecture is modular relative to the number of time bases (counter submodules) and channels (action submodules or timer I/O pins) that are included. The CTM6 consists of several submodules which are located on either side of the CTM6 internal submodule bus (SMB). All data and control signals within the CTM6 are passed over this bus. The SMB is connected to the outside world via the bus interface unit submodule (BIUSM), which is connected to the intermodule bus (IMB), and subsequently the CPU. This configuration allows the CPU to access the data and control registers in each CTM6 submodule on the SMB. Four local time base buses TBB[1:4], each 16-bits wide, are used to transfer timing information from counters to action submodules. Each CTM6 submodule can be connected to two TBBs. Figure 17 shows a block diagram of the CTM6. Freescale Semiconductor, Inc... 6.1 Overview The time base bus system connects the four counter submodules to the eleven double-action submodules (DASMs) and eight single-action submodules (SASM) channels. The bus interface unit submodule (BIUSM) allows all the CTM6 submodules to communicate to the IMB via the submodule bus (SMB). The counter prescaler submodule (CPSM) generates six different clock frequencies which can be used by any counter submodule. This submodule is contained within the BIUSM. The free-running counter submodule (FCSM) has a 16-bit up counter with an associated clock source selector, selectable time-base bus drivers, software writable control registers, software readable status bits, and interrupt logic. One FCSM is contained in the CTM6. The modulus counter submodule (MCSM) is an enhancement of the FCSM. A modulus register gives the additional flexibility of recycling the counter at a count other than 64K clock cycles. Three MCSMs are contained in the CTM6. The single action submodule (SASM) provides an input capture and an output compare for each of two bidirectional pins. A total of four SASMs (eight channels) are contained in the CTM6. The double-action submodule (DASM) provides two 16-bit input captures or two 16-bit output compare functions that can occur automatically without software intervention. Eleven DASMs are contained in the CTM6. The real-time clock submodule (RTCSM) provides a real time clock function independent of other CTM6 submodules. This time counter is driven by a dedicated low frequency oscillator (32.768 kHz) for low power consumption. A parallel port I/O submodule (PIOSM) handles up to eight input/output pins. Each pin of the PIOSM may be programmed as an input or an output under software control. One PIOSM is contained in the CTM6. The static RAM submodule (RAMSM) provides 32 bytes (16 words) of contiguous memory locations and takes the address space of four standard submodules. The RAMSM works as a stand-by memory. Two RAMSMs are contained in the CTM6. The standby power switch changes the power source of the RTCSM prescaler, counters, and oscillator, as well as the two RAMSMs to VRTC when VDD drops below its minimum specified value. MOTOROLA 78 For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. CIO5 CIO4 PORT I/O SUBMODULE (PIOSM17A) CIO3 CIO2 CIO1 CIO0 EXTERNAL CLOCK LOAD MODULUS COUNTER SUBMODULE (MCSM30) CLOCK PRESCALER SUBMODULE (CPSM) MODULUS COUNTER SUBMODULE (MCSM31) BUS INTERFACE UNIT SUBMODULE (BIUSM) CTS24A SINGLE ACTION SUBMODULE (SASM24B) CTS24B SINGLE ACTION SUBMODULE (SASM18A) CTS18A SINGLE ACTION SUBMODULE (SASM18B) CTS18B DOUBLE ACTION SUBMODULE (DASM26) CTD26 DOUBLE ACTION SUBMODULE (DASM27) CTD27 DOUBLE ACTION SUBMODULE (DASM28) CTD28 DOUBLE ACTION SUBMODULE (DASM29) CTD29 LOAD CTM31L Freescale Semiconductor, Inc... SINGLE ACTION SUBMODULE (SASM24A) TIME BASE BUS 1 TIME BASE BUS 2 EXTERNAL CLOCK LOAD SINGLE ACTION SUBMODULE (SASM12A) MODULUS COUNTER SUBMODULE (MCSM2) SINGLE ACTION SUBMODULE (SASM12B) FREE-RUNNING COUNTER SUBMODULE (FCSM3) SINGLE ACTION SUBMODULE (SASM14A) CTS14A SINGLE ACTION SUBMODULE (SASM14B) CTS14B DOUBLE ACTION SUBMODULE (DASM4) CTD4 DOUBLE ACTION SUBMODULE (DASM5) CTD5 DOUBLE ACTION SUBMODULE (DASM6) CTD6 DOUBLE ACTION SUBMODULE (DASM7) CTD7 DOUBLE ACTION SUBMODULE (DASM8) CTD8 DOUBLE ACTION SUBMODULE (DASM9) CTD9 DOUBLE ACTION SUBMODULE (DASM10) CTD10 TIME BASE BUS 4 TIME BASE BUS 3 SRAM SUBMODULE (RAMSM32) SRAM SUBMODULE (RAMSM36) VDD VDDSYN STANDBY POWER SWITCH VRTC VSSRTCOSC REAL-TIME CLOCK SUBMODULE (RTCSM16) EXRTC XRTC VSSRTCOSC GLOBAL TIME BASE BUS A GLOBAL TIME BASE BUS B CTM6 BLOCK Figure 17 CTM6 Block Diagram MC68CK338 MC68CK338TS/D For More Information On This Product, Go to: www.freescale.com MOTOROLA 79 Freescale Semiconductor, Inc. 6.2 Address Map The CTM6 address map occupies 512 bytes. All CTM6 registers are addressable in supervisor space only. Table 45 shows the CTM6 register. Table 45 CTM6 Address Map Freescale Semiconductor, Inc... Address 15 0 $YFF4001 BIUSM Module Configuration Register (BIUMCR) $YFF402 BIUSM Test Register (BIUTEST) $YFF404 BIUSM Time Base Register (BIUTBR) $YFF406 Reserved $YFF408 CPSM Control Register (CPCR) $YFF40A CPSM Test Register (CPTR) $YFF40C -$YFF40E Reserved $YFF410 MCSM2 Status/Interrupt/Control Register (MCSM2SICR) $YFF412 MCSM2 Counter Register (MCSM2CNT) $YFF414 MCSM2 Modulus Latch (MCSM2ML) $YFF416 Reserved $YFF418 FCSM3 Status/Interrupt/Control Register (FCSM3SIC) $YFF41A FCSM3 Counter Register (FCSM3CNT) $YFF41C - $YFF41E Reserved $YFF420 DASM4 Status/Interrupt/Control Register (DASM4SIC) $YFF422 DASM4 Register A (DASM4A) $YFF424 DASM4 Register B (DASM4B) $YFF426 Reserved $YFF428 DASM5 Status/Interrupt/Control Register (DASM5SIC) MOTOROLA 80 $YFF42A DASM5 Register A (DASM5A) $YFF42C DASM5 Register B (DASM5B) $YFF42E Reserved $YFF430 DASM6 Status/Interrupt/Control Register (DASM6SIC) $YFF432 DASM6 Register A (DASM6A) $YFF434 DASM6 Register B (DASM6B) $YFF436 Reserved $YFF438 DASM7 Status/Interrupt/Control Register (DASM7SIC) $YFF43A DASM7 Register A (DASM7A) $YFF43C DASM7 Register B (DASM7B) $YFF43E Reserved $YFF440 DASM8 Status/Interrupt/Control Register (DASM8SIC) $YFF442 DASM8 Register A (DASM8A) $YFF444 DASM8 Register B (DASM8B) $YFF446 Reserved $YFF448 DASM9 Status/Interrupt/Control Register (DASM9SIC) $YFF44A DASM9 Register A (DASM9A) $YFF44C DASM9 Register B (DASM9B) $YFF44E Reserved For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. Table 45 CTM6 Address Map (Continued) Freescale Semiconductor, Inc... Address 15 0 $YFF450 DASM10 Status/Interrupt/Control Register (DASM10SIC) $YFF452 DASM10 Register A (DASM10A) $YFF454 DASM10 Register B (DASM10B) $YFF456 - $YFF45E Reserved $YFF460 SASM12 Status/Interrupt/Control Register A (SIC12A) $YFF462 SASM12 Data Register A (S12DATA) $YFF464 SASM12 Status/Interrupt/Control Register B (SIC12B) $YFF466 SASM12 Data Register B (S12DATB) $YFF468 - $YFF46E Reserved $YFF470 SASM14 Status/Interrupt/Control Register A (SIC14A) $YFF472 SASM14 Data Register A (S14DATA) $YFF474 SASM14 Status/Interrupt/Control Register B (SIC14B) $YFF476 SASM14 Data Register B (S14DATB) $YFF478 - $YFF47E Reserved $YFF480 RTCSM16 Status/Interrupt/Control Register (RTC16SIC) $YFF482 RTCSM16 Prescaler Register (R16PRR) $YFF484 RTCSM16 32-Bit Free-Running Counter High (R16FRCH) $YFF486 RTCSM16 32-Bit Free-Running Counter Low (R16FRCL) $YFF488 PIOSM17A I/O Port Register (PIO17A) $YFF48A - $YFF48E Reserved $YFF490 SASM18 Status/Interrupt/Control Register A (SIC18A) $YFF492 SASM18 Data Register A (S18DATA) $YFF494 SASM18 Status/Interrupt/Control Register B (SIC18B) $YFF496 SASM18 Data Register B (S18DATB) $YFF498 -$YFF4BE Reserved $YFF4C0 SASM24 Status/Interrupt/Control Register A (SIC24A) $YFF4C2 SASM24 Data Register A (S24DATA) $YFF4C4 SASM24 Status/Interrupt/Control Register B (SIC24B) $YFF4C6 SASM24 Data Register B (S24DATB) $YFF4C8 - $YFF4CE Reserved $YFF4D0 DASM26 Status/Interrupt/Control Register (DASM26SIC) $YFF4D2 DASM26 Register A (DASM26A) $YFF4D4 DASM26 Register B (DASM26B) $YFF4D6 Reserved $YFF4D8 DASM27 Status/Interrupt/Control Register (DASM27SIC) $YFF4DA DASM27 Register A (DASM27A) $YFF4DC DASM27 Register B (DASM27B) $YFF4DE Reserved $YFF4E0 DASM28 Status/Interrupt/Control Register (DASM28SIC) $YFF4E2 DASM28 Register A (DASM28A) $YFF4E4 DASM28 Register B (DASM28B) $YFF4E6 Reserved MC68CK338 MC68CK338TS/D For More Information On This Product, Go to: www.freescale.com MOTOROLA 81 Freescale Semiconductor, Inc. Table 45 CTM6 Address Map (Continued) Freescale Semiconductor, Inc... Address 15 0 $YFF4E8 DASM29 Status/Interrupt/Control Register (DASM29SIC) $YFF4EA DASM29 Register A (DASM29A) $YFF4EC DASM29 Register B (DASM29B) $YFF4EE Reserved $YFF4F0 MCSM30 Status/Interrupt/Control Register (MCSM30SIC) $YFF4F2 MCSM30 Counter Register (MCSM30CNT) $YFF4F4 MCSM30 Modulus Latch (MCSM30ML) $YFF4F6 Reserved $YFF4F8 MCSM31 Status/Interrupt/Control Register (MCSM31SIC) $YFF4FA MCSM31 Counter Register (MCSM31CNT) $YFF4FC MCSM31 Modulus Latch (MCSM31ML) $YFF4FE Reserved $YFF500 - $YFF51E RAMSM32 RAM $YFF520 - $YFF53E RAMSM36 RAM $YFF540 - $YFF5FE Reserved NOTES: 1. Y = M111, where M is the logic state of the module mapping (MM) bit in the SIMLCR. 6.3 Time Base Bus System The time base bus system is composed of four 16-bit buses: TBB1, TBB2, TBB3 and TBB4. They are arranged so that each CTM6 submodule can be connected to two time base buses. Figure 18 shows that CTM6 submodules numbered 1 to M-1 can be connected to TBB3 and TBB4. CTM6 submodules M to N can be connected to TBB1 and TBB2. Control bits within each CTM6 submodule allow the software to connect the submodule to the desired time base bus(es). MOTOROLA 82 For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. TIME BASE BUS A (TBBA) TIME BASE BUS B (TBBB) TIME BASE BUS 3 (TBB3) SUBMODULE BUS (SMB) TIME BASE BUS 2 (TBB2) TIME BASE BUS 1 (TBB1) Freescale Semiconductor, Inc... SUBMODULE M+1 TIME BASE BUS 4 (TBB4) SUBMODULE M-1 SUBMODULE M SUBMODULE 2 SUBMODULE 1 SUBMODULE N BUS INTERFACE UNIT SUBMODULE (BIUSM) INTERMODULE BUS (IMB) CTM TBB BLOCK Figure 18 Time Base Bus Configuration As shown in Figure 18, each CTM submodule can access one of two global time base buses. TBB1 and TBB4 are collectively referred to as global time base bus TBBA. Likewise, TBB2 and TBB3 are collectively referred to as global time base bus TBBB. Table 46 shows which time base buses are available for each CTM6 submodule. Table 46 CTM6 Time Base Bus Allocation Global/Local Time Base Bus Allocation Global/Local Time Base Bus Allocation Submodule Global Bus A Global Bus B Submodule Global Bus A Global Bus B MCSM2 TBB4 TBB3 SASM18 TBB1 TBB2 FCSM3 TBB4 TBB3 SASM24 TBB1 TBB2 DASM4 - 10 TBB4 TBB3 DASM26 - 29 TBB1 TBB2 SASM12 - 14 TBB4 TBB3 MCSM30 - 31 TBB1 TBB2 Time base buses are used to transfer timing information from counters to action submodules. Each CTM6 submodule can either be a clock source module (and drive one or two of the time base buses) or an action submodule (and read and react to the timing information on the time base buses). MC68CK338 MC68CK338TS/D For More Information On This Product, Go to: www.freescale.com MOTOROLA 83 Freescale Semiconductor, Inc. The time base buses are precharge/discharge type buses with wired-OR capability, so that no hardware damage occurs when several counters are driving the same bus at the same time. 6.4 Bus Interface Unit Submodule (BIUSM) The BIUSM connects the SMB to the IMB and allows the CTM6 submodules to communicate with the CPU. The BIUSM also communicates interrupt requests from the CTM6 submodules to the IMB, and transfers the interrupt level, arbitration bit and vector number to the CPU during the interrupt acknowledge cycle. 6.4.1 BIUSM Registers Freescale Semiconductor, Inc... The BIUSM contains a module configuration register, a time base register, and a test register. The BIUSM register block always occupies the first four register locations in the CTM6 register space and cannot be relocated within the CTM6 structure. All unused bits and reserved address locations return zero when read by the software. Writing to unused bits and reserved address locations has no effect. BIUMCR -- BIU Module Configuration Register 15 14 13 STOP FRZ 0 12 VECT[7:6] 11 0 1 10 9 $YFF400 8 IARB[2:0] 7 6 5 4 3 2 1 0 0 0 TBRS1 0 0 0 0 TBRS0 0 0 0 0 0 0 0 0 RESET: 0 0 1 0 0 0 STOP -- Stop Enable The STOP bit, while asserted, completely stops operation of the CTM6. The BIUSM continues to operate to allow the CPU access to submodule registers. The CTM6 remains stopped until reset or until the STOP bit is negated by the CPU. 0 = Allows operation of the CTM6 1 = Stops operation of the CTM6 FRZ -- FREEZE Assertion Response 0 = Ignore IMB FREEZE signal 1 = CTM6 stops when IMB FREEZE signal is asserted NOTE Some submodules may validate this signal with internal enable bits. Bit 13 -- Not Implemented VECT[7:6] -- Interrupt Vector Base Number Field This bit field selects the interrupt vector base number for the CTM6. Of the eight bits necessary for vector number definition, the six least significant bits are programmed by hardware on a submodule basis, while the two remaining bits are provided by VECT[7:6]. This places the CTM6 vectors in one of four possible positions in the interrupt vector table. Refer to Table 47. Table 47 Interrupt Vector Base Number Bit Field MOTOROLA 84 VECT7 VECT6 Resulting Vector Base Number 0 0 $00 0 1 $40 1 0 $80 1 1 $C0 For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. IARB[2:0] -- Interrupt Arbitration Field This bit field and the IARB3 bit within each submodule provide 15 different interrupt arbitration numbers that can be used to arbitrate between interrupt requests occurring on the IMB with the same interrupt priority level. The IARB field defaults to zero on reset, preventing the module from arbitrating during an IACK cycle. If no arbitration takes place during the IACK cycle, the SIML generates a spurious interrupt, indicating to the system that the interrupt arbitration number has not been initialized. The CTM6 allows two different arbitration numbers to be used by providing each submodule with its own IARB3 bit (which can be set or cleared in software). Once IARB[2:0] are assigned in the BIUSM, they apply to all CTM6 interrupt requests. Therefore, CTM6 submodule interrupts can be prioritized with requests from other modules at the same interrupt level. IARB[2:0] are cleared by reset. Freescale Semiconductor, Inc... Bits[7:6], [4:1] -- Not Implemented TBRS1, TBRS0 -- Time Base Register Bus Select Bits These bits specify which time base bus is accessed when the time base register (BIUTBR) is read. Refer to Table 48. Table 48 Time Base Register Bus Select Bits TBRS1 TBRS0 Time Base Bus 0 0 TBB1 0 1 TBB2 1 0 TBB3 1 1 TBB4 BIUTEST -- BIUSM Test Register $YFF402 BIUTEST is used during factory testing of the CTM6. Accesses to BIUTEST must be made while the MCU is in test mode. BIUTBR -- BIUSM Time Base Register 15 14 $YFF404 13 12 11 10 9 8 7 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 RESET: 0 0 BIUTBR is a read-only register used to read the value present on one of the time base buses. The time base bus being accessed is determined by TBRS1 and TBRS0 in BIUMCR. Writing to BIUTBR has no effect during normal operation. 6.5 Counter Prescaler Submodule (CPSM) The counter prescaler submodule (CPSM) is a programmable divider system that provides the CTM6 counters with a choice of six clock signals (PCLKx) derived from the sixth frequency MCU system clock (fsys). Five of these frequencies are derived from a fixed divider chain. The divide ratio is software selectable from a choice of four divide ratios. The CPSM is contained within the BIUSM. Figure 19 shows a block diagram of the CPSM. MC68CK338 MC68CK338TS/D For More Information On This Product, Go to: www.freescale.com MOTOROLA 85 Freescale Semiconductor, Inc. FIRST CPSM PRESCALER fsys fsys / 2 PCLK1 = /2 or /3 /2 PCLK2 = /4 fsys / 4 fsys / 6 PCLK3 = fsys / 8 fsys / 12 PCLK4 = fsys / 16 fsys / 24 PCLK5 = fsys / 32 fsys / 48 PCLK6 = fsys / 64 fsys / 128 fsys / 256 fsys / 512 fsys / 96 fsys / 192 fsys / 384 fsys / 768 DIV23 = / 2 DIV23 = / 3 8-BIT /8 PRESCALER /16 /32 /64 SELECT /128 /256 Freescale Semiconductor, Inc... fsys / 3 PRUN DIV23 PSEL1 PSEL0 CPCR CTM CPSM BLOCK Figure 19 CPSM Block Diagram 6.5.1 CPSM Registers The CPSM contains a control register and a test register. All unused bits and reserved address locations return zero when read by the software. Writing to unused bits and reserved address locations has no effect. CPCR -- CPSM Control Register 15 14 13 12 11 $YFF408 10 9 8 7 6 5 4 NOT USED 3 2 PRUN DIV23 0 0 1 0 PSEL[1:0] RESET: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 PRUN -- Prescaler Running The PRUN bit is a read/write control bit that allows the software to switch the prescaler counter on and off. This bit allows the counters in various CTM6 submodules to be synchronized. It is cleared by reset. 0 = Prescaler is held in reset and is not running 1 = Prescaler is running DIV23 -- Divide By 2/Divide By 3 The DIV23 bit is a read/write control bit that selects the division ratio of the first prescaler counter. It may be changed by the software at any time and is cleared by reset. 0 = First prescaler stage divides by two 1 = First prescaler stage divides by three PSEL[1:0] -- Prescaler Division Ratio Select Field This bit field selects the division ratio of the programmable prescaler output signal (PCLK6). Refer to Table 49. MOTOROLA 86 For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. Table 49 Prescaler Division Ratio Select Field Freescale Semiconductor, Inc... Prescaler Control Register Bits Prescaler Division Ratio PRUN DIV23 PSEL1 PSEL0 PCLK1 PCLK2 PCLK3 PCLK4 PCLK5 PCLK6 0 X X X 0 0 0 0 0 0 1 0 0 0 2 4 8 16 32 64 1 0 0 1 2 4 8 16 32 128 1 0 1 0 2 4 8 16 32 256 1 0 1 1 2 4 8 16 32 512 1 1 0 0 3 6 12 24 48 96 1 1 0 1 3 6 12 24 48 192 1 1 1 0 3 6 12 24 48 384 1 1 1 1 3 6 12 24 48 768 CPTR -- CPSM Test Register $YFF40A CPTR is used during factory testing of the CTM6. Accesses to CPTR must be made while the MCU is in test mode. 6.6 Clock Sources for Counter Submodules One of seven clock sources can be chosen for each counter submodule. Five of them are fixed prescaler taps derived from the system clock: /2, /4, /8, /16, and /32. A sixth prescaler tap is software selectable as the system clock divided by 64, 128, 256, or 512. An alternate prescaler option provides fixed prescaler taps of the system clock divided by 3, 6, 12, 24, and 48. In this case, the software selectable tap is the system clock divided by 96, 192, 384, or 768. The seventh selectable clock source is an external pin which may trigger on the rising or falling edge of the input signal. The external input allows a clock frequency to be selected that is not based on the MCU system clock. Alternately, the external clock input allows a counter submodule to be used for pulse or event counting. NOTE The external clock inputs for MCSM30 and MCSM31 are tied to the I/O pin CTD5 for DASM5. The external clock inputs for MCSM2 and FCSM3 are tied to the I/O pin CTD27 for DASM27. 6.7 Free-Running Counter Submodule (FCSM) The free-running counter submodule (FCSM) has a 16-bit up counter with an associated clock source selector, selectable time-base bus drivers, software writable control registers, software readable status bits, and interrupt logic. When the 16-bit up counter overflows from $FFFF to $0000, an optional overflow interrupt may be generated. Software selects which, if any, time-base bus is to be driven by the 16-bit counter. A software control register selects whether the clock input to the counter is one of the taps from the prescaler or an input pin. The polarity of the external input pin is also programmable. One FCSM is contained in the CTM6. Figure 20 shows a block diagram of the FCSM. MC68CK338 MC68CK338TS/D For More Information On This Product, Go to: www.freescale.com MOTOROLA 87 Freescale Semiconductor, Inc. NOTE In order to count, the FCSM requires the CPSM clock signals to be present. On coming out of reset, the FCSM does not count internal or external events until the prescaler in the CPSM starts running (when the software sets the PRUN bit). This allows all counters in the CTM6 submodules to be synchronized. TBBA TIME BASE BUSES TBBB BUS SELECT 6 CLOCKS (PCLKX) FROM PRESCALER DRVA DRVB Freescale Semiconductor, Inc... CONTROL REGISTER BITS INPUT PIN CTMC CLOCK SELECT EDGE DETECT IN OVERFLOW INTERRUPT CONTROL 16-BIT UP COUNTER CLK2 CLK1 CLK0 COF CONTROL REGISTER BITS IL2 IL1 IL0 IARB3 CONTROL REGISTER BITS SUBMODULE BUS CTM FCSM BLOCK Figure 20 FCSM Block Diagram 6.7.1 FCSM Registers The FCSM contains a status/interrupt/control register and a counter register. All unused bits and reserved address locations return zero when read. Writing to unused bits and reserved address locations has no effect. FCSM3SIC -- FCSM Status/Interrupt/Control Register 15 14 COF 13 12 IL[2:0] $YFF418 11 10 9 8 7 6 5 4 3 IARB3 0 DRVA DRVB IN 0 0 0 0 0 0 0 0 U 0 0 0 0 2 1 0 CLK[2:0] RESET: 0 0 0 0 0 0 0 COF -- Counter Overflow Flag This status flag indicates whether or not a counter overflow has occurred. An overflow is defined to be the transition of the counter from $FFFF to $0000. If the IL field is non-zero, an interrupt request is generated when the COF bit is set. 0 = Counter overflow has not occurred 1 = Counter overflow has occurred This flag is set only by hardware and cleared only by software or a system reset. To clear the flag, first read the register with COF set to one, then write a zero to the bit. COF is cleared only if no overflow occurs between the read and write operations. MOTOROLA 88 For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. IL[2:0] -- Interrupt Level Setting IL[2:0] to a non-zero value causes the FCSM to request an interrupt of the selected level when the COF bit sets. If IL[2:0] = %000, no interrupt will be requested when COF sets. These bits can be read or written at any time and are cleared by reset. IARB3 -- Interrupt Arbitration Bit 3 This bit works in conjunction with IARB[2:0] in the BIUMCR. Each module that generates interrupt requests on the IMB must have a unique value in the arbitration field. This interrupt arbitration identification number is used to arbitrate for the IMB when modules generate simultaneous interrupts of the same priority. The IARB3 bit is cleared by reset. Refer to 6.4.1 BIUSM Registers for more information on IARB[2:0]. Freescale Semiconductor, Inc... DRV[A:B] -- Drive Time Base Bus This bit field contains read/write bits that control the connection of the FCSM to the time base buses A and B. These bits are cleared by reset. Refer to Table 52. Table 50 Drive Time Base Bus Field DRVA DRVB Bus Selected 0 0 No time base bus driven 0 1 Time base bus B is driven 1 0 Time base bus A is driven 1 1 Both time base buses A and B are driven WARNING Two time base buses should not be driven at the same time. IN -- Input Pin Status Bit This read-only status bit reflects the logic state of the FCSM input pin. Writing to this bit has no effect, nor does reset. NOTE The clock input of FCSM3 is internally connected to I/O pin CTD27 of DASM27 and will read the state of that pin. CLK[2:0] -- Counter Clock Select These read/write control bits select one of six internal clock signals (PCLK[1:6]) or one of two external conditions on the external clock input pin. Maximum frequency of the external clock signals is fsys/4. Refer to Table 54. Table 51 Counter Clock Select Field CLK2 CLK1 CLK0 Free-Running Counter Clock Source 0 0 0 PCLK1 (fsys / 2 or fsys / 3) 0 0 1 PCLK2 (fsys / 4 or fsys / 6) 0 1 0 PCLK3 (fsys / 8 or fsys / 12) 0 1 1 PCLK4 (fsys / 16 or fsys / 24) 1 0 0 PCLK5 (fsys / 32 or fsys / 48) 1 0 1 PCLK6 (fsys / 64 or fsys / 768) 1 1 0 External clock input, falling edge 1 1 1 External clock input, rising edge MC68CK338 MC68CK338TS/D For More Information On This Product, Go to: www.freescale.com MOTOROLA 89 Freescale Semiconductor, Inc. FCSM3CNT -- FCSM Counter Register 15 14 $YFF41A 13 12 11 10 9 8 7 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 RESET: 0 0 The FCSM counter register is a read/write register. A read returns the current value of the counter. A write loads the counter with the specified value. The counter then begins incrementing from this new value. Freescale Semiconductor, Inc... 6.8 Modulus Counter Submodule (MCSM) The modulus counter submodule (MCSM) is an enhancement of the FCSM. The MCSM contains a 16bit modulus latch, a 16-bit loadable up-counter, counter loading logic, a clock selector, a time base bus driver, and an interrupt interface. A modulus latch gives the additional flexibility of recycling the counter at a count other than 64-Kbyte clock cycles. The state of the modulus latch is transferred to the counter when an overflow occurs or when a user-specified edge transition occurs on an external input pin. In addition, a write to the modulus counter simultaneously loads both the counter and the modulus latch with the specified value. The counter then begins incrementing from this new value. Three MCSMs are contained in the CTM6. Figure 21 shows a block diagram of the MCSM. NOTE In order to count, the MCSM requires the CPSM clock signals to be present. On coming out of reset, the MCSM does not count internal or external events until the prescaler in the CPSM starts running (when the software sets the PRUN bit). This allows all counters in the CTM6 submodules to be synchronized. TBBA TIME BASE BUSES TBBB 6 CLOCKS (PCLKX) FROM PRESCALER BUS SELECT CLOCK INPUT PIN CTMC CLOCK SELECT EDGE DETECT DRVA DRVB CONTROL REGISTER BITS IN2 CLK2 CLK1 CLK0 CONTROL REGISTER BIT MODULUS LOAD INPUT PIN CTML CONTROL REGISTER BITS 16-BIT UP COUNTER OVERFLOW INTERRUPT CONTROL MODULUS CONTROL MODULUS LOAD INPUT PIN CTML MODULUS REGISTER EDGE DETECT WRITE BOTH IN1 CONTROL REGISTER BIT EDGEN EDGEP COF CONTROL REGISTER BITS IL2 IL1 IL0 IARB3 CONTROL REGISTER BITS SUBMODULE BUS CTM MCSM BLOCK Figure 21 MCSM Block Diagram MOTOROLA 90 For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. 6.8.1 MCSM Registers The MCSM contains a status/interrupt/control register, a counter, and a modulus latch. All unused bits and reserved address locations return zero when read. Writing to unused bits and reserved address locations has no effect. The CTM6 contains three MCSMs, each with its own set of registers. MCSM2SIC -- MCSM2 Status/Interrupt/Control Register MCSM30SIC -- MCSM30 Status/Interrupt/Control Register MCSM31SIC -- MCSM31 Status/Interrupt/Control Register 15 14 COF 13 12 IL[2:0] $YFF410 $YFF4F0 $YFF4F8 11 10 9 8 7 6 IARB3 0 DRVA DRVB IN2 IN1 0 0 0 0 0 0 5 4 EDGEN EDGEP 3 2 0 1 0 CLK[2:0] RESET: Freescale Semiconductor, Inc... 0 0 0 0 0 0 0 0 0 0 COF -- Counter Overflow Flag This status flag indicates whether or not a counter overflow has occurred. An overflow of the MCSM counter is defined to be the transition of the counter from $FFFF to $xxxx, where $xxxx is the value contained in the modulus latch. If the IL[2:0] field is non-zero, an interrupt request is generated when the COF bit is set. 0 = Counter overflow has not occurred 1 = Counter overflow has occurred This flag is set only by hardware and cleared only by software or by a system reset. To clear the flag, the software must first read the register with COF set to one, then write a zero to the bit. COF is cleared only if no overflow occurs between the read and write operations. IL[2:0] -- Interrupt Level Setting IL[2:0] to a non-zero value causes the MCSM to request an interrupt of the selected level when the COF bit sets. If IL[2:0] = %000, no interrupt will be requested when COF sets. These bits can be read or written at any time and are cleared by reset. IARB3 -- Interrupt Arbitration Bit 3 This bit works in conjunction with IARB[2:0] in the BIUMCR. Each module that generates interrupt requests on the IMB must have a unique value in the arbitration field. This interrupt arbitration identification number is used to arbitrate for the IMB when modules generate simultaneous interrupts of the same priority. The IARB3 bit is cleared by reset. Refer to 6.4.1 BIUSM Registers for more information on IARB[2:0]. DRV[A:B] -- Drive Time Base Bus This bit field contains read/write bits that control the connection of the MCSM to time base buses A and B. These bits are cleared by reset. Refer to Table 52. Table 52 Drive Time Base Bus Field DRVA DRVB Bus Selected 0 0 No time base bus is driven 0 1 Time base bus B is driven 1 0 Time base bus A is driven 1 1 Both time base buses A and B are driven WARNING Two time base buses should not be driven at the same time. MC68CK338 MC68CK338TS/D For More Information On This Product, Go to: www.freescale.com MOTOROLA 91 Freescale Semiconductor, Inc. IN2 -- Clock Input Pin Status This read-only status bit reflects the logic state of the clock input pin. Writing to this bit has no effect, nor does reset. NOTE The clock input of MCSM2 is internally connected to I/O pin CTD27 for DASM27 and will read the state of that pin. The clock inputs of MCSM30 and MCSM31 are internally connected to I/O pin CTD5 for DASM5 and will read the state of that pin. Freescale Semiconductor, Inc... IN1 -- Modulus Load Input Pin Status This read-only status bit reflects the logic state of the modulus load input pin. Writing to this bit has no effect, nor does reset. NOTE The load input of MCSM2 is internally connected to I/O pin CTD29 for DASM29 and will read the state of that pin. The load input of MCSM30 is internally connected to I/O pin CTD4 for DASM4 and will read the state of that pin. The load input of MCSM31 is available externally on the CTM31L pin. EDGEN, EDGEP -- Modulus Load Edge Sensitivity Bits These read/write control bits select the sensitivity of the edge detection circuitry on the modulus load pin CTML. Refer to Table 53. Table 53 Modulus Load Edge Sensitivity EDGEN EDGEP IN1 Edge Detector Sensitivity 0 0 None 0 1 Positive edge only 1 0 Negative edge only 1 1 Positive and negative edge CLK[2:0] -- Counter Clock Select These read/write control bits select one of six internal clock signals (PCLK[1:6]) or one of two external conditions on the external clock input pin (rising edge or falling edge). The maximum frequency of the external clock signals is fsys/4. Refer to Table 54. Table 54 Counter Clock Select MOTOROLA 92 CLK2 CLK1 CLK0 Free-Running Counter Clock Source 0 0 0 PCLK1 (fsys / 2 or fsys / 3) 0 0 1 PCLK2 (fsys / 4 or fsys / 6) 0 1 0 PCLK3 (fsys / 8 or fsys / 12) 0 1 1 PCLK4 (fsys / 16 or fsys / 24) 1 0 0 PCLK5 (fsys / 32 or fsys / 48) 1 0 1 PCLK6 (fsys / 64 or fsys / 768) 1 1 0 External clock input, falling edge 1 1 1 External clock input, rising edge For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. NOTE The clock input of MCSM2 is internally connected to I/O pin CTD27 for DASM27 and will read the state of that pin. The clock inputs of MCSM30 and MCSM31 are internally connected to I/O pin CTD5 for DASM5 and will read the state of that pin. MCSM2CNT -- MCSM2 Counter Register MCSM30CNT -- MCSM30 Counter Register MCSM31CNT -- MCSM31 Counter Register 15 14 $YFF412 $YFF4F2 $YFF4FA 13 12 11 10 9 8 7 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 RESET: Freescale Semiconductor, Inc... 0 0 The MCSM counter register is a read/write register. A read returns the current value of the counter. A write simultaneously loads both the counter and the MCSM modulus latch with the specified value. The counter then begins incrementing from this new value. MCSM2ML -- MCSM2 Modulus Latch MCSM30ML -- MCSM30 Modulus Latch MCSM31ML -- MCSM31 Modulus Latch 15 14 $YFF414 $YFF4F4 $YFF4FC 13 12 11 10 9 8 7 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 RESET: 0 0 The MCSM modulus latch register is a read/write register. A read returns the current value of the latch. A write pre-loads the latch with a new value that the modulus counter will begin counting from when the next load condition occurs. 6.9 Single Action Submodule (SASM) The single action submodule (SASM) provides two identical channels, each having its own input/output pin, but sharing the same interrupt logic, priority level, and arbitration number. Each channel can be configured independently to perform either input capture or output compare. Table 55 shows the different operational modes. Table 55 SASM Operational Modes Mode Function IC1 Input capture either on a rising or falling edge or as a read-only input port OC2 Output compare OCT2 OP2 Output compare and toggle Output port NOTES: 1. When a channel is operating in IC mode, the IN bit in the SIC register reflects the logic state of the corresponding input pin (after being Schmitt triggered and synchronized). 2. When a channel is operating in OC, OCT, or OP mode, the IN bit in the SIC register reflects the logic state of the output of the output flip-flop. MC68CK338 MC68CK338TS/D For More Information On This Product, Go to: www.freescale.com MOTOROLA 93 Freescale Semiconductor, Inc. NOTE All of the functions associated with one pin are called a SASM channel. The SASM can perform a single timing action (input capture or output compare) before software intervention is required. Each channel includes a 16-bit comparator and one 16-bit register for saving an input capture value or for holding an output compare value. The input edge detector associated with each pin is programmable to cause the capture function to occur on the rising or falling edge. The output flip flop can be set to either toggle when an output compare occurs or to transfer a software-provided bit value to the output pin. In either input capture or output compare mode, each channel can be programmed to generate an interrupt. One of the two incoming time-base buses may be selected for each channel. Each channel can also work as a simple I/O pin. Freescale Semiconductor, Inc... A total of four SASMs (eight channels) are contained in the CTM6. Figure 22 shows a block diagram of the SASM. SINGLE ACTION CHANNEL A FLAG IL2 IL1 IL0 IARB3 IEN I/O PIN INTERRUPT CONTROL FLAG SINGLE ACTION CHANNEL B I/O PIN SUBMODULE BUS CTM TIME BASE BUSES CTM SASM BLOCK Figure 22 SASM Block Diagram 6.9.1 SASM Registers The SASM contains two status/interrupt/control registers (A and B) and two data registers (A and B). All unused bits and reserved address locations return zero when read. Writing to unused bits and reserved address locations has no effect. The CTM6 contains four SASMs, each with its own set of registers. SIC12A, SIC14A -- SASM Status/Interrupt/Control Register A SIC18A, SIC24A -- SASM Status/Interrupt/Control Register A 15 14 FLAG 13 12 IL[2:0] $YFF460, $YFF470 $YFF490, $YFF4C0 11 10 9 8 7 6 IARB3 IEN 0 BSL IN 0 0 0 0 0 U 0 5 4 FORCE EDOUT 3 2 1 0 0 MODE[1:0] 0 0 0 0 RESET: 0 0 MOTOROLA 94 0 0 0 0 For More Information On This Product, Go to: www.freescale.com 0 MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. SIC12B, SIC14B -- SASM Status/Interrupt/Control Register B SIC18B, SIC24B -- SASM Status/Interrupt/Control Register B $YFF464, $YFF474 $YFF494, $YFF4C4 15 14 13 12 11 10 9 8 7 6 FLAG 0 0 0 0 IEN 0 BSL IN 0 0 0 0 0 0 0 0 U 0 5 4 FORCE EDOUT 3 2 1 0 0 0 MODE[1:0] 0 0 0 RESET: 0 0 0 0 Freescale Semiconductor, Inc... SICA and SICB contain the control and status bits for SASM channels A and B, respectively. SICA also contains the IL[2:0] interrupt level field and IARB3 interrupt arbitration bit 3 for both SASM channels A and B. FLAG -- Event Flag FLAG indicates whether or not an input capture or output compare event has occurred. If the IL[2:0] field is non-zero, and IEN is set, an interrupt request is generated when FLAG is set. 0 = An input capture or output compare event has not occurred 1 = An input capture or output compare event has occurred Table 56 shows the event flag status during different modes. Table 56 Event Flag Status Conditions Mode Status Description IC If a subsequent input capture event occurs while FLAG is set, the new value is latched and FLAG remains set. OC If a subsequent output compare event occurs while FLAG is set, the compare occurs normally and FLAG remains set. OCT If a subsequent output compare event occurs while FLAG is set, the output signal toggles normally and FLAG remains set. OP If a subsequent internal compare event occurs while FLAG is set, the compare occurs normally and FLAG remains set. FLAG is set only by hardware and cleared only by software or by a system reset.To clear this bit, first read the register with FLAG set to one, then write a zero to the bit. NOTE The flag clearing mechanism works only if no flag setting event occurs between the read and write operations. If a FLAG setting event occurs between the read and write operations, the FLAG bit will not cleared. IL[2:0] -- Interrupt Level Setting IP[2:0] to a non-zero value causes the SASM to request an interrupt when the FLAG bit sets. If IL[2:0] = %000, no interrupts will be requested when FLAG sets. NOTE This field affects both SASM channels, not just channel A. IARB3 -- Interrupt Arbitration Bit 3 This bit works in conjunction with IARB[2:0] in the BIUMCR. Each module that generates interrupt requests on the IMB must have a unique value in the arbitration field. This interrupt arbitration identification number is used to arbitrate for the IMB when modules generate simultaneous interrupts of the same priority. The IARB3 bit is cleared by reset. Refer to 6.4.1 BIUSM Registers for more information on IARB[2:0]. MC68CK338 MC68CK338TS/D For More Information On This Product, Go to: www.freescale.com MOTOROLA 95 Freescale Semiconductor, Inc. NOTE This bit field affects both SASM channels, not just channel A. IEN -- Interrupt Enable This control bit enables interrupts when FLAG is set and the IL[2:0] field is non-zero. 0 = Interrupts disabled 1 = Interrupts enabled BSL -- Time Base Bus Select This control bit selects the time base bus connected to the SASM. 0 = Time base bus A selected 1 = Time base bus B selected Freescale Semiconductor, Inc... IN -- Input Pin Status In input mode (IC), the IN bit reflects the logic state present on the corresponding input pin after being Schmitt triggered and synchronized. In the output modes (OC, OCT and OP), the IN bit value reflects the state of the output flip-flop. The IN bit is a read-only bit. Reset has no effect on this bit. NOTE The input of SASM12A is internally connected to I/O pin CTD29 and will read the state of that pin. The input of SASM12B is internally connected to I/O pin CTD26 and will read the state of that pin. FORCE -- Force Compare Control In the IC and OP modes, FORCE is not used and writing to it has no effect. In the OC and OCT modes, FORCE is used by software to cause the output flip-flop (and the output pin) to behave as though an output compare had occurred. In OC and OCT mode, setting FORCE causes the value of EDOUT to be transferred to the output of the output flip-flop. Internal synchronization ensures that the correct level appears on the output pin when a new value is written to EDOUT and FORCE is set at the same time. 0 = No action 1 = Force output flip-flop to behave as if an output compare has occurred FORCE is cleared by reset and always reads as zero. NOTE FLAG is not affected by the use of the FORCE bit. EDOUT -- Edge Detect and Output Level In IC mode, EDOUT is used to select the edge that triggers the input capture circuitry. 0 = Input capture on falling edge 1 = Input capture on rising edge In OC and OCT mode, the EDOUT bit is used to latch the value to be output to the pin on the next output compare match or when the FORCE is set. Internal synchronization ensures that the correct level appears on the output pin when a new value is written to EDOUT and FORCE is set at the same time. Reading EDOUT returns the previous value written. In OP mode, the value of EDOUT is output to the corresponding pin. Reading EDOUT returns the previous value written. MODE[1:0] -- SASM Operating Mode This bit field selects the mode of operation for the SASM channel. Refer to Table 57. MOTOROLA 96 For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. Table 57 SASM Operating Mode Select MODE1 MODE2 SASM Channel Operating Mode 0 0 Input capture (IC) 0 1 Output port (OP) 1 0 Output compare (OC) 1 1 Output compare and toggle (OCT) S12DATA, S14DATA -- SASM Data Register A S18DATA, S24DATA -- SASM Data Register A 15 14 $YFF462, $YFF472 $YFF492, $YFF4C2 13 12 11 10 9 8 7 6 5 4 3 2 1 0 U U U U U U U U U U U U U U Freescale Semiconductor, Inc... RESET: U U S12DATB, S14DATB -- SASM Data Register B S18DATB, S24DATB -- SASM Data Register B 15 14 $YFF464, $YFF474 $YFF494, $YFF4C4 13 12 11 10 9 8 7 6 5 4 3 2 1 0 U U U U U U U U U U U U U U RESET: U U SDATA and SDATB are the data registers associated with SASM channels A and B, respectively. In IC mode, SDATA and SDATB contain the last captured value. In the OC, OCT and OP modes, SDATA and SDATB are loaded with the value of the next output compare. 6.10 Double-Action Submodule (DASM) The double-action submodule (DASM) provides two 16-bit input capture or two 16-bit output compare functions that can occur automatically without software intervention. The input edge detector is programmable to cause the capture function to occur on user-specified edges. The output flip flop is set by one of the output compare signals and reset by the other one. The DASM input capture and the output compare modes may optionally generate interrupts. Software determines which of the two incoming time-base buses is used for input captures or output compares. Six operating modes allow software to use DASM input capture and output compare functions to perform pulse-width measurement, period measurement, single pulse generation, and continuous pulse width modulation, as well as standard input capture and output compare. The DASM can also work as a single I/O pin. DASM operation is determined by the mode select bit field MODE[3:0] in the DASM status/interrupt/control (DASMSIC) register. Table 58 shows the different DASM modes of operation. MC68CK338 MC68CK338TS/D For More Information On This Product, Go to: www.freescale.com MOTOROLA 97 Freescale Semiconductor, Inc. Table 58 DASM Modes of Operation Mode Description of Mode DIS Disabled -- I/O pin is placed in a high impedance state IPWM Input pulse width measurement -- Capture on leading and the trailing edges of an input pulse IPM Input period measurement -- Capture on two consecutive rising or falling edges of an input pulse Freescale Semiconductor, Inc... IC Input capture -- Capture on user-specified edge OCB Output compare, flag set on channel B match -- Generate leading and trailing edges of an output pulse and set flag on second edge OCAB Output compare, flag set on channels A and B match -- Generate leading and trailing edges of an output pulse and set flag on both edges OPWM Output pulse width modulation -- Generate continuous PWM output with 7, 9, 11, 12, 13, 14, 15, or 16 bits of resolution The DASM is composed of two timing channels (A and B), an output flip-flop, an input edge detector, some control logic and an interrupt interface. All control and status bits are contained in the DASMSIC register. Channel A consists of one 16-bit data register and one 16-bit comparator. To the user, channel B also appears to consist of one 16-bit data register and one 16-bit comparator, though internally, channel B has two data registers (B1 and B2). The operating mode determines which register is accessed by the software. Refer to Table 59. Table 59 Channel B Data Register Access Mode Data Register IPWM, IPM, IC Registers A and B2 are used to hold the captured values. In these modes, the B1 register is used as a temporary latch for channel B. OCA, OCAB Registers A and B2 are used to define the output pulse. Register B1 is not used in these modes. OPWM Registers A and B1 are used as primary registers and hidden register B2 is used as a double buffer for channel B. Register contents are always transferred automatically at the correct time so that the minimum pulse (measurement or generation) is just one time base bus count. The A and B data registers are always read/write registers, accessible via the CTM6 submodule bus. Eleven DASMs are contained in the CTM6. Figure 23 shows a block diagram of the DASM. MOTOROLA 98 For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. TBBA 2 TIME BASE BUSES TBBB BUS SELECT FORCA FORCB BSL OUTPUT FLIP-FLOP 16-BIT COMPARATOR A 16-BIT REGISTER A IN OUTPUT BUFFER I/O PIN EDPOL EDGE DETECT 16-BIT REGISTER B1 Freescale Semiconductor, Inc... WOR REGISTER B INTERRUPT CONTROL 16-BIT REGISTER B2 16-BIT COMPARATOR B FLAG MODE3 MODE2 MODE1 MODE0 CONTROL REGISTER BITS IL2 IL1 IL0 IARB3 CONTROL REGISTER BITS SUBMODULE BUS CTM DASM BLOCK Figure 23 DASM Block Diagram 6.10.1 DASM Registers The DASM contains one status/interrupt/control register and two data registers (A and B). All unused bits and reserved address locations return zero when read. Writing to unused bits and reserved address locations has no effect. The CTM6 contains 11 DASMs, each with its own set of registers. DASM4SIC, DASM5SIC -- DASM Status/Interrupt/Control Register DASM6SIC, DASM7SIC -- DASM Status/Interrupt/Control Register DASM8SIC, DASM9SIC -- DASM Status/Interrupt/Control Register DASM10SIC, DASM26SIC -- DASM Status/Interrupt/Control Register DASM27SIC, DASM28SIC -- DASM Status/Interrupt/Control Register DASM29SIC -- DASM Status/Interrupt/Control Register 15 14 FLAG 13 12 IL[2:0] 11 10 9 8 7 IARB3 0 WOR BSL IN 0 0 0 0 0 6 5 $YFF420, $YFF428 $YFF430, $YFF438 $YFF440, $YFF448 $YFF450, $YFF4D0 $YFF4D8, $YFF4E0 $YFF4E8 4 3 FORCA FORCB EDPOL 2 1 0 MODE[3:0] RESET: 0 0 0 MC68CK338 MC68CK338TS/D 0 0 0 0 For More Information On This Product, Go to: www.freescale.com 0 0 0 0 MOTOROLA 99 Freescale Semiconductor, Inc. FLAG -- Event Flag This status bit indicates whether or not an input capture or output compare event has occurred. If the IL[2:0] field is non-zero, an interrupt request is generated when FLAG is set. 0 = An input capture or output compare event has not occurred 1 = An input capture or output compare event has occurred Table 56 shows the event flag status during different modes. Table 60 Event Flag Status Conditions Mode DIS IPWM IPM Freescale Semiconductor, Inc... IC Status Description FLAG bit is cleared FLAG bit is set each time there is a capture on channel A FLAG bit is set each time there is a capture on channel A, except for the first time FLAG bit is set each time there is a capture on channel A OCB FLAG bit is set each time there is a successful comparison on channel B OCAB FLAG bit is set each time there is a successful comparison on either channel A or B OPWM FLAG bit is set each time there is a successful comparison on channel A FLAG is set only by hardware and cleared by software or by a system reset. To clear the bit, first read the register with FLAG set to one, then write a zero to the bit. Placing the DASM in DIS mode will also clear the flag. NOTE The flag clearing mechanism works only if no flag setting event occurs between the read and write operations. If a FLAG setting event occurs between the read and write operations, the FLAG bit will not be cleared. IL[2:0] -- Interrupt Level Setting IL[2:0] to a non-zero value causes the DASM to request an interrupt when the FLAG bit sets. If IL[2:0] = %000, no interrupt will be requested when FLAG sets. IARB3 -- Interrupt Arbitration Bit 3 This bit works in conjunction with IARB[2:0] in the BIUMCR. Each module that generates interrupt requests on the IMB must have a unique value in the arbitration field. This interrupt arbitration identification number is used to arbitrate for the IMB when modules generate simultaneous interrupts of the same priority. The IARB3 bit is cleared by reset. Refer to 6.4.1 BIUSM Registers for more information on IARB[2:0]. WOR -- Wired-OR Mode In the DIS, IPWM, IPM and IC modes, WOR is not used. Reading this bit returns the value that was previously written. In the OCB, OCAB and OPWM modes, WOR selects whether the output buffer is configured for normal or open drain operation. 0 = Output buffer operates in normal mode 1 = Output buffer operates in open drain mode BSL -- Bus Select This bit selects the time base bus connected to the DASM. 0 = DASM is connected to time base bus A. 1 = DASM is connected to time base bus B. MOTOROLA 100 For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. IN -- Input Pin Status In the DIS, IPWM, IPM and IC modes, this read-only status bit reflects the logic level on the input pin. In the OCB, OCAB and OPWM modes, reading this bit returns the value latched on the output flip-flop, after EDPOL polarity selection. Writing to this bit has no effect. FORCA -- Force A In the OCB, OCAB and OPWM modes, FORCA allows software to force the output flip-flop to behave as if a successful comparison had occurred on channel A (except that the FLAG bit is not set). Writing a one to FORCA sets the output flip-flop; writing a zero has no effect. Freescale Semiconductor, Inc... In the DIS, IPWM, IPM and IC modes, FORCA is not used and writing to it has no effect. FORCA is cleared by reset, and always reads as zero. NOTE Writing a one to both FORCA and FORCB simultaneously resets the output flipflop. FORCB -- Force B In the OCB, OCAB and OPWM modes, FORCB allows software to force the output flip-flop to behave as if a successful comparison had occurred on channel B (except that the FLAG bit is not set). Writing a one to FORCB sets the output flip-flop, writing a zero has no effect. In the DIS, IPWM, IPM and IC modes, FORCB is not used and writing to it has no effect. FORCB is cleared by reset, and always reads as zero. NOTE Writing a one to both FORCA and FORCB simultaneously resets the output flipflop. EDPOL -- Edge Polarity EDPOL selects different options depending on the DASM operating mode. Refer to Table 61. Table 61 Edge Polarity MODE EDPOL DIS X EDPOL is not used in DIS mode 0 Channel A captures on a rising edge Channel B captures on a falling edge 1 Channel A captures on a falling edge Channel B captures on a rising edge 0 Channel A captures on a rising edge 1 Channel A captures on a falling edge 0 A compare on channel A sets the output pin to logic one A compare on channel B clears the output pin to logic zero 1 A compare on channel A clears the output pin to logic zero A compare on channel B sets the output pin to logic one IPWM IPM, IC OCB, OCAB, OPWM Function MODE[3:0] -- DASM Mode Select This bit field selects the operating mode of the DASM. Refer to Table 62. MC68CK338 MC68CK338TS/D For More Information On This Product, Go to: www.freescale.com MOTOROLA 101 Freescale Semiconductor, Inc. NOTE To avoid spurious interrupts, DASM interrupts should be disabled before changing the operating mode. Freescale Semiconductor, Inc... Table 62 DASM Mode Select Field MODE[3:0] Bits of Resolution Time Base Bits Ignored 0000 -- -- DIS -- Disabled 0001 16 -- IPWM -- Input pulse width measurement 0010 16 -- IPM -- Input measurement period 0011 16 -- IC -- Input capture 0100 16 -- OCB -- Output compare, flag on B compare 0101 16 -- OCAB -- Output compare, flag on A and B compare DASM Operating Mode 011X -- -- Not used 1000 16 -- OPWM -- Output pulse-width modulation 1001 15 15 OPWM -- Output pulse-width modulation 1010 14 [15:14] OPWM -- Output pulse-width modulation 1011 13 [15:13] OPWM -- Output pulse-width modulation 1100 12 [15:12] OPWM -- Output pulse-width modulation 1101 11 [15:11] OPWM -- Output pulse-width modulation 1110 9 [15:9] OPWM -- Output pulse-width modulation 1111 7 [15:7] OPWM -- Output pulse-width modulation DASM4A, DASM5A -- DASM Data Register A DASM6A, DASM7A -- DASM Data Register A DASM8A, DASM9A -- DASM Data Register A DASM10A, DASM26A -- DASM Data Register A DASM27A, DASM28A --DASM Data Register A DASM29A -- DASM Data Register A 15 14 $YFF422, $YFF42A $YFF432, $YFF43A $YFF442, $YFF44A $YFF452, $YFF4D2 $YFF4DA, $YFF4E2 $YFF4EA 13 12 11 10 9 8 7 6 5 4 3 2 1 0 U U U U U U U U U U U U U U RESET: U U DASMA is the data register associated with channel A. Table 63 shows how the DASMA is used with the different operating modes. MOTOROLA 102 For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. Table 63 DASMA Operations Mode Freescale Semiconductor, Inc... DIS DASMA Operation DASMA can be accessed to prepare a value for a subsequent mode selection IPWM DASMA contains the captured value corresponding to the trailing edge of the measured pulse IPM DASMA contains the captured value corresponding to the most recently detected user-specified rising or falling edge IC DASMA contains the captured value corresponding to the most recently detected user-specified rising or falling edge OCB DASMA is loaded with the value corresponding to the leading edge of the pulse to be generated. Writing to DASMA in the OCB and OCAB modes also enables the corresponding channel A comparator until the next successful comparison. OCAB DASMA is loaded with the value corresponding to the leading edge of the pulse to be generated. Writing to DASMA in the OCB and OCAB modes also enables the corresponding channel A comparator until the next successful comparison. OPWM DASMA is loaded with the value corresponding to the leading edge of the PWM pulse to be generated. DASM4B, DASM5B -- DASM Data Register B DASM6B, DASM7B -- DASM Data Register B DASM8B, DASM9B -- DASM Data Register B DASM10B, DASM26B -- DASM Data Register B DASM27B, DASM28B -- DASM Data Register B DASM29B -- DASM Data Register B 15 14 $YFF424, $YFF42C $YFF434, $YFF43C $YFF444, $YFF44C $YFF454, $YFF4D4 $YFF4DC, $YFF4E4 $YFF4EC 13 12 11 10 9 8 7 6 5 4 3 2 1 0 U U U U U U U U U U U U U U RESET: U U DASMB is the data register associated with channel B. Table 64 shows how DASMB is used with the different operating modes. Depending on the mode selected, software access is to register B1 or register B2. MC68CK338 MC68CK338TS/D For More Information On This Product, Go to: www.freescale.com MOTOROLA 103 Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... Table 64 DASMB Operations Mode DASMB Operation DIS DASMB can be accessed to prepare a value for a subsequent mode selection. In this mode, register B1 is accessed in order to prepare a value for the OPWM mode. Unused register B2 is hidden and cannot be read, but is written with the same value when register B1 is written. IPWM DASMB contains the captured value corresponding to the trailing edge of the measured pulse. In this mode, register B2 is accessed. Buffer register B1 is hidden and cannot be accessed. IPM DASMB contains the captured value corresponding to the most recently detected user-specified rising or falling edge. In this mode, register B2 is accessed. Buffer register B1 is hidden and cannot be accessed. IC DASMB contains the captured value corresponding to the most recently detected user-specified rising or falling edge. In this mode, register B2 is accessed. Buffer register B1 is hidden and cannot be accessed. OCB DASMB is loaded with the value corresponding to the trailing edge of the pulse to be generated. Writing to DASMB in the OCB and OCAB modes also enables the corresponding channel B comparator until the next successful comparison. In this mode, register B2 is accessed. Buffer register B1 is hidden and cannot be accessed. OCAB DASMB is loaded with the value corresponding to the trailing edge of the pulse to be generated. Writing to DASMB in the OCB and OCAB modes also enables the corresponding channel B comparator until the next successful comparison. In this mode, register B2 is accessed. Buffer register B1 is hidden and cannot be accessed. OPWM DASMB is loaded with the value corresponding to the trailing edge of the PWM pulse to be generated. In this mode, register B1 is accessed. Buffer register B2 is hidden and cannot be accessed 6.11 Real-Time Clock Submodule (RTCSM) with Low-Power Oscillator The real -ime clock submodule provides a real-time clock independent of other CTM6 submodules. This time counter is driven by a dedicated low frequency oscillator (32.768 kHz) for low power consumption. The RTCSM contains a 15-bit prescaler and a 32-bit free-running counter, from which seconds, minutes, hours and days can be determined. The RTCSM can also generate interrupts at one second intervals. The low-power oscillator, prescaler, and counter portions of the RTCSM may be sustained by a separate power supply (VRTC) for battery backup when VDD is off. The RTCSM and the low-power oscillator can be disabled for minimum power consumption on VRTC when VDD is powered off. This is useful for maximizing the shelf life of the standby battery. Refer to 6.14 RTCSM and RAMSM Standby Operation for more information. One RTCSM is contained in the CTM6. Figure 24 shows a block diagram of the RTCSM. MOTOROLA 104 For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. 32.768 kHz 10 pF 1 pF1 1 10 k EXTAL XTAL Freescale Semiconductor, Inc... 1 Hz 32-BIT FREE-RUNNING COUNTER 15-BIT PRESCALER 32-BIT FREE-RUNNING COUNTER BUFFER 15-BIT PRESCALER BUFFER INTERRUPT LOGIC STATUS, INTERRUPT, AND CONTROL REGISTER BITS FLAG (1 Hz) ARB3 LOW POWER OSCILLATOR CONTROL LOGIC INTERRUPT LEVEL WRITE ENABLE ENABLE WEN EN SUBMODULE BUS NOTES: 1. RESISTANCE AND CAPACITANCE BASED ON A TEST CIRCUIT CONSTRUCTED WITH A DAISHINKU DMX-38 32.768 kHz CRYSTAL. SPECIFIC COMPONENTS MUST BE BASED ON CRYSTAL TYPE. CONTACT CRYSTAL VENDOR FOR EXACT CIRCUIT. CTM RTC BLOCK Figure 24 RTCSM Block Diagram 6.11.1 RTCSM Registers The RTCSM contains one status/interrupt/control register, one 15-bit prescaler register and two 32-bit free-running counter registers (high and low). All unused bits and reserved address locations return zero when read. Writing to unused bits and reserved address locations has no effect. RTC16SIC -- RTCSM Status/Interrupt/Control Register 15 14 TICKF 13 12 IL[2:0] 11 10 9 8 IARB3 0 WEN EN 0 0 0 U $YFF480 7 6 5 4 3 2 1 0 0 0 0 NOT USED RESET: U 0 0 0 0 0 0 0 0 TICKF -- 1 Hz Clock Tick Flag TICKF is set each time the 32-bit free-running counter is incremented. Software can clear TICKF by reading the bit as a one, then writing a zero to it. If the IL[2:0] field is non-zero, an interrupt request is generated when TICKF is set. TICKF is not affected by reset. MC68CK338 MC68CK338TS/D For More Information On This Product, Go to: www.freescale.com MOTOROLA 105 Freescale Semiconductor, Inc. NOTE TICKF is only cleared if the 32-bit free-running counter does not increment between reading RTC16SIC with TICKF set to one and then writing TICKF to zero. IL[2:0] -- Interrupt Level Field Setting IL[2:0] to a non-zero value causes the RTCSM to request an interrupt of the selected level when the TICKF bit sets. If IL[2:0] = %000, no interrupt will be requested when TICKF sets. Freescale Semiconductor, Inc... IARB3 -- Interrupt Arbitration Bit 3 This bit works in conjunction with IARB[2:0] in the BIUMCR. Each module that generates interrupt requests on the IMB must have a unique value in the arbitration field. This interrupt arbitration identification number is used to arbitrate for the IMB when modules generate simultaneous interrupts of the same priority. The IARB3 bit is cleared by reset. Refer to 6.4.1 BIUSM Registers for more information on IARB[2:0]. WEN -- Write Enable Control This bit allows the 15-bit prescaler and the 32-bit free-running counter to be updated. Normally, these are read-only registers. Regular write operations have no effect. When the WEN bit is written to one, it sets a latch that allows the 15-bit prescaler and the 32-bit free-running counter to be written. The latch is automatically reset when the prescaler is written. To write a new value to the complete counter chain: * Write a one to the WEN bit. * Execute a long-word write to the 32-bit free-running counter high (R16FRCH) register. * Execute a word write to the 15-bit prescaler (R16PRR) register. WEN cannot be written to one again until the writes to update the prescaler and free-running counter have been completed. The WEN bit always reads as zero. EN -- RTCSM Enable This bit selects whether the RTCSM is running or not. 0 = RTCSM is not running 1 = RTCSM is running The EN bit is not affected by reset. If the RTCSM is not to be used, it is recommended that EN be cleared as soon as the MCU comes out of reset. R16PRR -- RTCSM Prescaler Register 15 14 $YFF482 13 12 11 10 9 8 7 6 5 4 3 2 1 0 U U U U U U U U U U U U U 0 RESET: U U R16PRR contains the synchronized value of the 15-bit prescaler or the value to be loaded into the 15bit prescaler. NOTE When the RTCSM is disabled, writing to the 15-bit prescaler and 32-bit freerunning counter may give unpredictable results. MOTOROLA 106 For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. R16FRCH -- RTCSM Free-Running Counter High Register 15 14 $YFF484 13 12 11 10 9 8 7 6 5 4 3 2 1 0 U U U U U U U U U U U U U U RESET: U U R16FRCH contains the synchronized high word value of the 32-bit free-running counter or the value to be loaded into the high word 32-bit free-running counter. NOTE When the RTCSM is disabled, writing to the 15-bit prescaler and 32-bit free-running counter may give unpredictable results. Freescale Semiconductor, Inc... R16FRCL -- RTCSM Free-Running Counter Low Register 15 14 $YFF486 13 12 11 10 9 8 7 6 5 4 3 2 1 0 U U U U U U U U U U U U U U RESET: U U R16FRCL contains the synchronized low word value of the 32-bit free-running counter or the value to be loaded into the low word 32-bit free-running counter. NOTE When the RTCSM is disabled, writing to the 15-bit prescaler and 32-bit free-running counter may give unpredictable results. 6.12 Parallel Port I/O Submodule (PIOSM) The port I/O submodule (PIOSM) provides I/O capability independent of other CTM6 modules. The PIOSM handles up to eight input/output pins. One PIOSM is contained in the CTM6. Figure 25 shows a block diagram of the PIOSM. DATA DIRECTION REGISTER OUTPUT DATA REGISTER I/O PIN OUTPUT DRIVER OUTPUT DATA BIT INPUT DATA BIT INPUT SUBMODULE BUS CTM PIOSM BLOCK Figure 25 PIOSM Block Diagram MC68CK338 MC68CK338TS/D For More Information On This Product, Go to: www.freescale.com MOTOROLA 107 Freescale Semiconductor, Inc. 6.12.1 PIOSM Register The PIOSM control register is composed of two 8-bit registers. The upper eight bits contain the data register and the lower eight bits contain the data direction register. Each PIOSM pin may be programmed as an input or an output under software control. The data direction register controls whether the corresponding pins are inputs or outputs. The PIOSM data register can be read or written by the processor. For pins programmed as outputs, a read of the data register actually reads the value of the output data latch and not the I/O pin. PIO17A -- PIOSM Control Register $YFF488 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 DATA7 DATA6 DATA5 DATA4 DATA3 DATA2 DATA1 DATA0 DDR7 DDR6 DDR5 DDR4 DDR3 DDR2 DDR1 DDR0 U U U U U U 0 0 0 0 0 0 0 0 RESET: Freescale Semiconductor, Inc... 0 0 CTIO[7:6] are not bonded to pins on the MC68338. When one of these signals is configured as an input, a read of the corresponding data bit always returns a zero. When one of these signals is configured as an output, a read of the corresponding data bit returns the value stored in the output data latch. NOTE Care should be taken when a single word write cycle is used to modify the data register and data direction register of the PIOSM. Undesired glitches can occur on pins that change from inputs to outputs and vice versa. To avoid this, first use a byte write cycle to modify the data register then use another byte write cycle to modify the data direction register. 6.13 Static RAM Submodule (RAMSM) The static RAM submodule (RAMSM) provides 32 bytes (16 words) of contiguous memory locations and is not relocatable. It is especially useful for storage of variables and system parameters that must be maintained when the rest of the MCU is powered down. Data can be read or written in bytes, words, or long words. RAMSM locations are not affected by reset. The CTM6 has two RAMSMs. Table 65 shows the RAMSM address locations. Table 65 RAMSM Address Locations Static RAM Submodule Address 32 $YFF500-51E 36 $YFF520-53E 6.14 RTCSM and RAMSM Standby Operation The standby power switch in CTM6 monitors VDD and selects either VDD and VDDSYN or VRTC for the power source of the RTCSM and RAMSMs, depending on the level of VDD. When VDD is within the specified operating range, the RTCSM low-power oscillator is powered by VDDSYN and the RAMSMs are powered by VDD. VDD also provides power to the digital logic portion of the RTCSM, therefore both VDD and VDDSYN must be kept equal to each other for normal operation. When VDD and VDDSYN are powered down, the submodules are powered by VRTC and are in standby mode. In standby mode, the RTCSM continues to keep time if enabled. However, updates to the 15-bit prescaler and 32-bit free-running counter buffer registers are halted in order to conserve power. All MOTOROLA 108 For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. RTCSM registers are write protected in standby mode to prevent loss of data in runaway situations. For the same reason, the RAMSMs are also write protected in standby mode. If the standby mode function is not required in a given application, VRTC should be powered from the VDD and VDDSYN supply. Unpredictable operation of the RAMSMs and RTCSM may result otherwise. 6.15 CTM6 Interrupts The CTM6 is able to request numerous interrupts on the IMB. Each submodule that is able to request interrupts can do so with any of seven levels. Each submodule that is able to request interrupts includes a 3-bit level number and a 1-bit arbitration number that is initialized by software. Freescale Semiconductor, Inc... The 3-bit level number selects which of seven interrupt signals on the IMB are driven by that submodule to create an interrupt request. Of the four priority bits provided on the IMB during arbitration among the modules, one of them comes from the chosen submodule, and the BIUSM provides the other three. Thus, the CTM6 responds to two of the possible 15 arbitration numbers. During the IMB arbitration process, the BIUSM manages the separate arbitration among the CTM6 submodules to determine which submodule should respond. Of the submodules which have an interrupt request pending at the level being arbitrated on the IMB, the submodule which has the lowest address is given the highest priority to respond. When the IARB number is not unique for a given module, simultaneous interrupts are prioritized in hardware according to the vector number or the submodule interrupt arbitration sequence number shown in Table 66. Following the interrupt arbitration process, the CTM6 provides an 8-bit vector number. Six of the eight bits are provided by the submodules. A submodule can identify two separate interrupt sources with unique interrupt vectors. The two high-order bits of the 8-bit vector are provided by the BIUSM. The six low-order vector bits identify the highest priority interrupt request pending in the CTM6 at the beginning of the arbitration cycle. MC68CK338 MC68CK338TS/D For More Information On This Product, Go to: www.freescale.com MOTOROLA 109 Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... Table 66 CTM6 Interrupt Priority and Vector/Pin Allocation Submodule Name Submodule Base Address1 Submodule Interrupt Vector Number2 Submodule Interrupt Arbitration Sequence Number3 BIUSM $YFF400 None None CPSM $YFF408 None None MCSM2 $YFF410 xx000010 2 FCSM3 $YFF418 xx000011 3 DASM4 $YFF420 xx000100 4 DASM5 $YFF428 xx000101 5 DASM6 $YFF430 xx000110 6 DASM7 $YFF438 xx000111 7 DASM8 $YFF440 xx001000 8 DASM9 $YFF448 xx001001 9 DASM10 $YFF450 xx001010 10 SASM12 $YFF460 xx001100 12 SASM14 $YFF470 xx001110 14 RTCSM16 $YFF480 xx010000 16 PIOSM17A $YFF488 -- -- SASM18 $YFF490 xx010010 18 SASM24 $YFF4C0 xx011000 24 DASM26 $YFF4D0 xx011010 26 DASM27 $YFF4D8 xx011011 27 DASM28 $YFF4E0 xx011100 28 DASM29 $YFF4E8 xx011101 29 MCSM30 $YFF4F0 xx011110 30 MCSM31 $YFF4F8 xx011111 31 RAMSM32 $YFF500 -- -- RAMSM36 $YFF520 -- -- NOTES: 1. Y = m111, where m is the state of the MM bit in SIMLCR of the SIML (Y = $7 or $F). 2. "xx" represents VECT[7:6], which is located in the BIUSM module configuration register. 3. Submodule interrupt arbitration number 2 is the highest priority; arbitration number 63 is the lowest priority. MOTOROLA 110 For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. 7 Electrical Characteristics This section contains electrical specification tables and reference timing diagrams. Table 67 Maximum Ratings Freescale Semiconductor, Inc... Num Symbol Value Unit 1 Supply Voltage1, 2, 3 Rating VDD - 0.3 to + 6.5 V 2 Input Voltage1, 2, 3, 4 Vin - 0.3 to + 6.5 V 3 Instantaneous Maximum Current Single pin limit (applies to all pins)1, 3, 5, 6 ID 25 mA 4 Operating Maximum Current Digital Input Disruptive Current5, 6, 7 VSS - 0.3 VIN VDD + 0.3 IID - 500 to + 500 A 5 Operating Temperature Range TA TL to TH C - 40 to + 85 6 Storage Temperature Range Tstg - 55 to + 150 C NOTES: 1. Permanent damage can occur if maximum ratings are exceeded. Exposure to voltages or currents in excess of recommended values affects device reliability. Device modules may not operate normally while being exposed to electrical extremes. 2. Although sections of the device contain circuitry to protect against damage from high static voltages or electrical fields, take normal precautions to avoid exposure to voltages higher than maximum-rated voltages. 3. This parameter is periodically sampled rather than 100% tested. 4. All pins except TSC. 5. All functional non-supply pins are internally clamped to VSS for transitions below VSS. All functional pins except EXTAL and XFC are internally clamped to VDD for transitions below VDD. 6. Power supply must maintain regulation within operating VDD range during instantaneous and operating maximum current conditions. 7. Total input current for all digital input-only and all digital input/output pins must not exceed 10 mA. Exceeding this limit can cause disruption of normal operation. MC68CK338 MC68CK338TS/D For More Information On This Product, Go to: www.freescale.com MOTOROLA 111 Freescale Semiconductor, Inc. Table 68 Thermal Characteristics Num 1 Characteristic Symbol Value Unit JA 48 C/W Thermal Resistance Plastic 144-Pin Surface Mount The average chip-junction temperature (TJ) in C can be obtained from: T J = T A + ( P D x JA ) (1) Freescale Semiconductor, Inc... where: TA = Ambient Temperature, C JA = Package Thermal Resistance, Junction-to-Ambient, C/W PD = PINT + PI/O PINT = IDD x VDD, Watts -- Chip Internal Power PI/O = Power Dissipation on Input and Output Pins -- User Determined For most applications PI/O < PINT and can be neglected. An approximate relationship between PD and TJ (if PI/O is neglected) is: P D = K / ( T J + 273C ) (2) Solving equations 1 and 2 for K gives: K = P D + ( T A + 273C ) + JA x P D2 (3) where K is a constant pertaining to the particular part. K can be determined from equation (3) by measuring PD (at equilibrium) for a known TA. Using this value of K, the values of PD and TJ can be obtained by solving equations (1) and (2) iteratively for any value of TA. MOTOROLA 112 For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. Table 69 Clock Control Timing (VDD and VDDSYN = 2.7 to 3.6 Vdc, VSS = 0 Vdc, TA = TL to TH) Freescale Semiconductor, Inc... Num Characteristic Range1 Symbol Min Max Unit 1 PLL Reference Frequency fref 25 50 kHz 2 System Frequency2 On-Chip PLL System Frequency Range External Clock Operation fsys dc 4(fref) dc 14.4 14.4 14.4 MHz 3 PLL Lock Time1, 3, 4, 5, 6 tlpll -- 20 ms fVCO -- 2 (fsys max) MHz Frequency7 4 VCO 5 Limp Mode Clock Frequency SYNCR X bit = 0 SYNCR X bit = 1 flimp -- -- fsys max/2 fsys max MHz 6 CLKOUT Jitter1, 4, 5, 6, 8 Short term (5 s interval) Long term (500 s interval) Jclk - 0.5 - 0.05 0.5 0.05 % NOTES: 1. Tested with a 32.768 kHz reference. 2. All internal registers retain data at 0 Hz. 3. Assumes that stable VDDSYN is applied, and that the crystal oscillator is stable. Lock time is measured from the time VDD and VDDSYN are valid until RESET is released. This specification also applies to the period required for PLL lock after changing the W and Y frequency control bits in the synthesizer control register (SYNCR) while the PLL is running, and to the period required for the clock to lock after LPSTOP. 4. This parameter is periodically sampled rather than 100% tested. 5. Assumes that a low-leakage external filter network is used to condition clock synthesizer input voltage. Total external resistance from the XFC pin due to external leakage must be greater than 15 M to guarantee this specification. Filter network geometry can vary depending upon operating environment. 6. Proper layout procedures must be followed to achieve specifications. 7. Internal VCO frequency (fVCO) is determined by SYNCR W and Y bit values. The SYNCR X bit controls a divide-by-two circuit that is not in the synthesizer feedback loop. When X = 0, the divider is enabled, and fsys = fVCO / 4. When X = 1, the divider is disabled, and fsys = fVCO / 2. X must equal one when operating at maximum specified fsys. 8. Jitter is the average deviation from the programmed frequency measured over the specified interval at maximum fsys. Measurements are made with the device powered by filtered supplies and clocked by a stable external clock signal. Noise injected into the PLL circuitry via VDDSYN and VSS and variation in crystal oscillator frequency increase the Jclk percentage for a given interval. When clock jitter is a critical constraint on control system operation, this parameter should be measured during functional testing of the final system. MC68CK338 MC68CK338TS/D For More Information On This Product, Go to: www.freescale.com MOTOROLA 113 Freescale Semiconductor, Inc. Table 70 DC Characteristics (VDD and VDDSYN = 2.7 to 3.6 Vdc, VSS = 0 Vdc, TA = TL to TH) Freescale Semiconductor, Inc... Num Characteristic Symbol Min Max Unit 1 Input High Voltage VIH 0.7 (VDD) VDD + 0.3 V 2 Input Low Voltage VIL VSS - 0.3 0.2 (VDD) V 3 Input 4 Hysteresis1 VHYS 0.5 -- V Input Leakage Current2 Vin = VDD or VSS Input-only pins IIN -2.5 2.5 A 5 High Impedance (Off-State) Leakage Current2 Vin = VDD or VSS All input/output and output pins IOZ -2.5 2.5 A 6 CMOS Output High Voltage2, 3 IOH = -10.0 A Group 1, 2, 4 input/output and all output pins VOH VDD - 0.2 -- V 7 CMOS Output Low Voltage2 IOL = 10.0 A Group 1, 2, 4 input/output and all output pins VOL -- 0.2 V 8 Output High Voltage2, 3 IOH = -0.4 mA Group 1, 2, 4 input/output and all output pins VOH VDD - 0.5 -- V 9 Output Low Voltage2 IOL = 0.8 mA Group 1 I/O Pins, CLKOUT, FREEZE/QUOT, IPIPE/DSO IOL = 2.65 mA Group 2 and Group 4 I/O Pins, CSBOOT, BG/CS1 IOL = 6 mA Group 3 VOL -- -- -- 0.4 0.4 0.4 V 10 Three State Control Input High Voltage VIHTSC 2.7 (VDD) 9.1 V IMSP -- -8 -95 -- A Current4 11 Data Bus Mode Select Pull-up Vin = VIL DATA[15:0] DATA[15:0] Vin = VIH 12 VDD Supply Current5 Run6 LPSTOP, (STCPU = 0, External clock input frequency = max fsys) LPSTOP, (STCPU = 1, External clock input frequency = max fsys) STOP7, (STCPU = 1, External clock input frequency = max fsys) IDD SIDD SIDD SIDD -- -- -- 46 2 18 13 mA mA mA mA 13 VRTC Voltage VSB 2.2 3.6 V -- -- -- 1.0 0.200 0 A A A IDDSYN -- -- -- 750 1.5 300 A mA A PD -- 171 mW Current8 14 15 16 VRTC CTM6-RTCSM oscillator enabled, VDD = VSS CTM6-RTCSM oscillator disabled, VDD = VSS VDD = VDDSYN 2.7 V VDDSYN Supply Current5 VCO on, 32.768 kHz crystal reference, maximum fsys External Clock, maximum fsys LPSTOP, 32.768 kHz crystal reference, VCO off (STSIM = 0) Power Dissipation9 MOTOROLA 114 ISB For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. Table 70 DC Characteristics (Continued) (VDD and VDDSYN = 2.7 to 3.6 Vdc, VSS = 0 Vdc, TA = TL to TH) Freescale Semiconductor, Inc... Num Characteristic Symbol Min Max Unit -- -- 10 20 pF -- -- -- -- 90 100 130 200 17 Input Capacitance2, 10 All input-only pins All input/output pins CIN 18 Load Capacitance2 Group 1 I/O Pins, CLKOUT, FREEZE/QUOT, IPIPE/DSO Group 2 I/O Pins and CSBOOT, BG/CS1 Group 3 I/O Pins Group 4 I/O Pins CL pF NOTES: 1. Applies to: CTM6 pins QSM pins IRQ[7:1], RESET, EXTAL, TSC, RMC, BKPT/DSCLK, IFETCH/DSI 2. Input-Only Pins: TSC, BKPT/DSCLK, RXD Output-Only Pins: CSBOOT, BG/CS1, CLKOUT, FREEZE/QUOT, IPIPE/DSO Input/Output Pins: Group 1: DATA[15:0], IFETCH/DSI, all CTM6 pins except CTM31L Group 2: ADDR[23:19]/CS[10:6], FC[2:0]/CS[5:3], DSACK[1:0], AVEC, RMC, DS, AS, SIZ[1:0],IRQ[7:1, MODCLK, ADDR[18:0], R/W, BERR, BR/CS0, BGACK/CS2, PCS[3:1], PCS0/SS, TXD Group 3: HALT, RESET Group 4: MISO, MOSI, SCK 3. Does not apply to HALT and RESET because they are open drain pins. Does not apply to MISO, MOSI, SCK, PCS0/SS, PCS[3:1], and TXD in wired-OR mode. Does not apply to CTD[29:26] and CTD[10:4] in wired-OR mode. 4. Use of an active pulldown device is recommended. 5. Total operating current is the sum of the appropriate VDD supply and VDDSYN supply current. 6. Current measured with system clock frequency of 14.4 MHz, all modules active. 7. LPSTOP with STCPU = 1 (clock turned off at CPU32L but IMB clock active) plus QSM and CTM6 STOP bits set. 8. VRTC current measured when VDD and VDDSYN are equal to VSS and VRTC is equal to VSBMAX. 9. Power dissipation is measured with a system clock frequency of 14.4 MHz, all modules active. Power dissipation is calculated using the following expression: PD = 3.6V (IDDSYN + IDD) 10. Input capacitance is periodically sampled rather than 100% tested. MC68CK338 MC68CK338TS/D For More Information On This Product, Go to: www.freescale.com MOTOROLA 115 Freescale Semiconductor, Inc. Table 71 AC Timing (VDD and VDDSYN = 2.7 to 3.6 Vdc, VSS = 0 Vdc, TA = TL to TH)1 Num Freescale Semiconductor, Inc... F1 Characteristic Frequency of Operation Symbol Min Max Unit f 0 14.4 MHz 1 Clock Period tcyc 69.4 -- ns 1A ECLK Period tEcyc 555 -- ns 1B External Clock Input Period2 tXcyc 69.4 -- ns 2, 3 Clock Pulse Width tCW 24.7 -- ns 2A, 3A ECLK Pulse Width tECW 277.5 -- ns 2B, 3B External Clock Input High/Low Time2 tXCHL 34.7 -- ns tCrf -- 10 ns trf -- 10 ns 4, 5 CLKOUT Rise and Fall Time 4A, 5A Rise and Fall Time -- All Outputs Except CLKOUT 6 Clock High to ADDR, FC, SIZE, RMC Valid tCHAV 0 35 ns 7 Clock High to ADDR, DATA, FC, SIZE, RMC High Impedance tCHAZx 0 69 ns 8 Clock High to ADDR, FC, SIZE, RMC Invalid tCHAZn 0 -- ns 9 Clock Low to AS, DS, CS Asserted tCLSA 2 25 ns 9A AS to DS or CS Asserted (Read)3 tSTSA -15 15 ns 9C Clock Low to IFETCH, IPIPE Asserted tCLIA 2 31 ns 11 ADDR, FC, SIZE, RMC Valid to AS, CS, (and DS Read) Asserted tAVSA 15 -- ns 12 Clock Low to AS, DS, CS Negated tCLSN 2 35 ns Clock Low to IFETCH, IPIPE Negated tCLIN 2 31 ns 13 AS, DS, CS Negated to ADDR, FC SIZE Invalid (Address Hold) tSNAI 19 -- ns 14 AS, CS (and DS Read) Width Asserted tSWA 138 -- ns 12A 14A DS, CS Width Asserted (Write) tSWAW 44 -- ns 14B AS, CS (and DS Read) Width Asserted (Fast Cycle) tSWDW 44 -- ns tSN 44 -- ns 15 AS, DS, CS Width Negated4 16 Clock High to AS, DS, R/W High Impedance tCHSZ -- 69 ns 17 AS, DS, CS Negated to R/W High tSNRN 19 -- ns 18 Clock High to R/W High tCHRH 0 35 ns 20 Clock High to R/W Low tCHRL 0 35 ns 21 R/W High to AS, CS Asserted tRAAA 19 -- ns 22 R/W Low to DS, CS Asserted (Write) tRASA 80 -- ns 23 Clock High to Data Out Valid tCHDO -- 35 ns 24 Data Out Valid to Negating Edge of AS, CS (Fast Write Cycle) tDVASN 19 -- ns 25 DS, CS Negated to Data Out Invalid (Data Out Hold) tSNDOI 19 -- ns 26 Data Out Valid to DS, CS Asserted (Write) tDVSA 19 -- ns MOTOROLA 116 For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. Table 71 AC Timing (Continued) (VDD and VDDSYN = 2.7 to 3.6 Vdc, VSS = 0 Vdc, TA = TL to TH)1 Num Symbol Min Max Unit tDICL 5 -- ns Late BERR, HALT Asserted to Clock Low (Setup Time) tBELCL 25 -- ns AS, DS Negated to DSACK[1:0], BERR, HALT, AVEC Negated tSNDN 0 100 ns tSNDI 0 -- ns DS, CS Negated to Data In High Impedance5, 6 tSHDI -- 65 ns CLKOUT Low to Data In Invalid (Fast Cycle Hold)5 tCLDI 19 -- ns CLKOUT Low to Data In High Impedance5 tCLDH -- 100 ns 31 DSACK[1:0] Asserted to Data In Valid7 tDADI -- 58 ns 33 Clock Low to BG Asserted/Negated tCLBAN -- 35 ns tBRAGA 1 -- tcyc tGAGN 1 2 tcyc 27 27A 28 29 29A 30 Freescale Semiconductor, Inc... 30A Characteristic Data In Valid to Clock Low (Data Setup) DS, CS Negated to Data In Invalid (Data In Hold)5 Asserted)8 35 BR Asserted to BG Asserted (RMC Not 37 BGACK Asserted to BG Negated 39 BG Width Negated tGH 2 -- tcyc 39A BG Width Asserted tGA 1 -- tcyc R/W Width Asserted (Write or Read) tRWA 174 -- ns 46A R/W Width Asserted (Fast Write or Read Cycle) tRWAS 104 -- ns 47A Asynchronous Input Setup Time BR, BGACK, DSACK[1:0], BERR, AVEC, HALT tAIST 10 -- ns 47B Asynchronous Input Hold Time tAIHT 19 -- ns 48 DSACK[1:0] Asserted to BERR, HALT Asserted9 tDABA -- 35 ns 53 Data Out Hold from Clock High tDOCH 0 -- ns 54 Clock High to Data Out High Impedance tCHDH -- 35 ns 55 R/W Asserted to Data Bus Impedance Change tRADC 55 -- ns 56 RESET Pulse Width (Reset Instruction) tHRPW 512 -- tcyc 57 BERR Negated to HALT Negated (Rerun) tBNHN 0 -- ns 70 Clock Low to Data Bus Driven (Show Cycle) tSCLDD 0 35 ns 71 Data Setup Time to Clock Low (Show Cycle) tSCLDS 19 -- ns 72 Data Hold from Clock Low (Show Cycle) tSCLDH 10 -- ns 73 BKPT Input Setup Time tBKST 19 -- ns 74 BKPT Input Hold Time tBKHT 13 -- ns 75 Mode Select Setup Time (DATA[15:0], MODCLK, BKPT) tMSS 20 -- tcyc 76 Mode Select Hold Time (DATA[15:0], MODCLK, BKPT) tMSH 0 -- ns tRSTA 4 -- tcyc tRSTR -- 10 tcyc 46 Time10 77 RESET Assertion 78 RESET Rise Time11, 12 MC68CK338 MC68CK338TS/D For More Information On This Product, Go to: www.freescale.com MOTOROLA 117 Freescale Semiconductor, Inc... Freescale Semiconductor, Inc. NOTES: 1. All AC timing is shown with respect to 20% VDD and 70% VDD levels unless otherwise noted. 2. When an external clock is used, minimum high and low times are based on a 50% duty cycle. The minimum allowable tXcyc period is reduced when the duty cycle of the external clock varies. The relationship between external clock input duty cycle and minimum tXcyc is expressed: Minimum tXcyc period = minimum tXCHL / (50% - external clock input duty cycle tolerance). 3. Specification 9A is the worst-case skew between AS and DS or CS. The amount of skew depends on the relative loading of these signals. When loads are kept within specified limits, skew will not cause AS and DS to fall outside the limits shown in specification 9. 4. If multiple chip selects are used, CS width negated (specification 15) applies to the time from the negation of a heavily loaded chip select to the assertion of a lightly loaded chip select. The CS width negated specification between multiple chip selects does not apply to chip selects being used for synchronous ECLK cycles. 5. Hold times are specified with respect to DS or CS on asynchronous reads and with respect to CLKOUT on fast cycle reads. The user is free to use either hold time. 6. Maximum value is equal to (tcyc / 2) + 25 ns. 7. If the asynchronous setup time (specification 47A) requirements are satisfied, the DSACK[1:0] low to data setup time (specification 31) and DSACK[1:0] low to BERR low setup time (specification 48) can be ignored. The data must only satisfy the data-in to clock low setup time (specification 27) for the following clock cycle. BERR must satisfy only the late BERR low to clock low setup time (specification 27A) for the following clock cycle. 8. To ensure coherency during every operand transfer, BG is not asserted in response to BR until after all cycles of the current operand transfer are complete. 9. In the absence of DSACK[1:0], BERR is an asynchronous input using the asynchronous setup time (specification 47A). 10. After external RESET negation is detected, a short transition period (approximately 2 tcyc) elapses, then the SIML drives RESET low for 512 tcyc. 11. External assertion of the RESET input can overlap internally-generated resets. To ensure that an external reset is recognized in all cases, RESET must be asserted for at least 590 CLKOUT cycles. 12. External logic must pull RESET high during this period in order for normal MCU operation to begin. MOTOROLA 118 For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. 1 2 4 3 CLKOUT 5 NOTE: TIMING SHOWN WITH RESPECT TO 20% AND 70% VDD. 68300 CLKOUT TIM Freescale Semiconductor, Inc... Figure 26 CLKOUT Output Timing Diagram 1B 2B 4B 3B EXTAL 5B NOTE: TIMING SHOWN WITH RESPECT TO 20% AND 70% VDD. PULSE WIDTH SHOWN WITH RESPECT TO 50% VDD. 68300 EXT CLK INPUT TIM Figure 27 External Clock Input Timing Diagram 1A 2A 4A 3A ECLK 5A NOTE: TIMING SHOWN WITH RESPECT TO 20% AND 70% VDD. 68300 ECLK OUTPUT TIM Figure 28 ECLK Output Timing Diagram MC68CK338 MC68CK338TS/D For More Information On This Product, Go to: www.freescale.com MOTOROLA 119 Freescale Semiconductor, Inc. S0 S1 S2 S3 S4 S5 CLKOUT 8 6 ADDR[23:20] FC[2:0] SIZ[1:0] 11 15 14 AS 13 Freescale Semiconductor, Inc... 9 DS 9A 12 CS 17 18 20 21 R/W 46 DSACK0 47A 28 DSACK1 29 31 DATA[15:0] 27 29A BERR 48 27A HALT 9C 12A 12A IFETCH 73 74 BKPT 47A 47B ASYNCHRONOUS INPUTS 68300 RD CYC TIM Figure 29 Read Cycle Timing Diagram MOTOROLA 120 For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. S0 S1 S2 S3 S4 S5 CLKOUT 6 8 ADDR[23:20] FC[2:0] SIZ[1:0] 11 15 14 AS 13 Freescale Semiconductor, Inc... 9 DS 21 9 12 CS 20 22 14A 17 R/W 46 DSACK0 47A 28 DSACK1 55 25 DATA[15:0] 23 26 54 53 BERR 48 27A HALT 74 73 BKPT 68300 WR CYC TIM Figure 30 Write Cycle Timing Diagram MC68CK338 MC68CK338TS/D For More Information On This Product, Go to: www.freescale.com MOTOROLA 121 Freescale Semiconductor, Inc. S0 S1 S4 S5 S0 CLKOUT 8 6 ADDR[23:0] FC[2:0] SIZ[1:0] 14B AS 12 9 Freescale Semiconductor, Inc... DS CS 20 18 46A R/W 30 27 30A DATA[15:0] 29A 73 29 BKPT 74 68300 FAST RD CYC TIM Figure 31 Fast Termination Read Cycle Timing Diagram MOTOROLA 122 For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. S0 S1 S4 S5 S0 CLKOUT 6 8 ADDR[23:0] FC[2:0] SIZ[1:0] 14B AS Freescale Semiconductor, Inc... 9 12 DS CS 46A 20 R/W 23 24 18 DATA[15:0] 73 25 BKPT 74 68300 FAST WR CYC TIM Figure 32 Fast Termination Write Cycle Timing Diagram MC68CK338 MC68CK338TS/D For More Information On This Product, Go to: www.freescale.com MOTOROLA 123 Freescale Semiconductor, Inc. S0 S1 S2 S3 S4 S5 S98 A5 A5 A2 CLKOUT ADDR[23:0] 7 DATA[15:0] AS Freescale Semiconductor, Inc... 16 DS R/W DSACK0 DSACK1 47A BR 39A 35 BG 33 33 BGACK 37 68300 BUS ARB TIM Figure 33 Bus Arbitration Timing Diagram -- Active Bus Case MOTOROLA 124 For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. A0 A5 A5 A2 A3 A0 CLKOUT ADDR[23:0] DATA[15:0] AS 47A 47A Freescale Semiconductor, Inc... BR 35 37 BG 33 33 47A BGACK 68300 BUS ARB TIM IDLE Figure 34 Bus Arbitration Timing Diagram -- Idle Bus Case MC68CK338 MC68CK338TS/D For More Information On This Product, Go to: www.freescale.com MOTOROLA 125 Freescale Semiconductor, Inc. S0 S41 S42 S43 S0 S1 S2 CLKOUT 6 8 ADDR[23:0] 18 R/W 20 AS 9 12 15 DS Freescale Semiconductor, Inc... 71 70 72 DATA[15:0] 73 74 BKPT SHOW CYCLE START OF EXTERNAL CYCLE NOTE: Show cycles can stretch during clock phase S42 when bus accesses take longer than two cycles due to IMB module wait-state insertion. 68300 SHW CYC TIM Figure 35 Show Cycle Timing Diagram MOTOROLA 126 For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. S0 S1 S2 S3 S4 S5 S0 S1 S2 S3 S4 S5 CLKOUT 6 8 6 ADDR[23:0] FC[2:0] SIZ[1:0] 14 11 11 14 13 AS 15 Freescale Semiconductor, Inc... 9 9 DS 9 17 17 21 12 21 12 CS 20 18 18 14A 46 R/W 46 29 25 55 DATA[15:0] 27 29A 53 23 54 68300 CHIP SEL TIM Figure 36 Chip Select Timing Diagram 77 78 RESET 75 DATA[15:0], MODCLK, BKPT 76 68300 RST/MODE SEL TIM Figure 37 Reset and Mode Select Timing Diagram MC68CK338 MC68CK338TS/D For More Information On This Product, Go to: www.freescale.com MOTOROLA 127 Freescale Semiconductor, Inc. Table 72 Background Debugging Mode Timing (VDD and VDDSYN = 2.7 to 3.6 Vdc, VSS = 0 Vdc, TA = TL to TH)1 Freescale Semiconductor, Inc... Num Characteristic Symbol Min Max Unit B0 DSI Input Setup Time tDSISU 19 -- ns B1 DSI Input Hold Time tDSIH 13 -- ns B2 DSCLK Setup Time tDSCSU 19 -- ns B3 DSCLK Hold Time tDSCH 13 -- ns B4 DSO Delay Time tDSOD -- 35 ns B5 DSCLK Cycle Time tDSCCYC 2 -- tcyc B6 CLKOUT High to FREEZE Asserted/Negated tFRZAN -- 64 ns B7 CLKOUT High to IFETCH High Impedance tIFZ -- 64 ns B8 CLKOUT High to IFETCH Valid tIF -- 64 ns B9 DSCLK Low Time tDSCLO 1 -- tcyc NOTES: 1. All AC timing is shown with respect to 20% VDD and 70% VDD levels unless otherwise noted. CLKOUT FREEZE B3 B2 BKPT/DSCLK B9 B5 B1 B0 IFETCH/DSI B4 IPIPE/DSO 68300 BKGD DBM SER COM TIM Figure 38 Background Debugging Mode Timing Diagram -- Serial Communication MOTOROLA 128 For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. CLKOUT B6 FREEZE B6 B7 IFETCH/DSI B8 68300 BDM FRZ TIM Freescale Semiconductor, Inc... Figure 39 Background Debugging Mode Timing Diagram -- Freeze Assertion Table 73 ECLK Bus Timing (VDD and VDDSYN = 2.7 to 3.6 Vdc, VSS = 0 Vdc, TA = TL to TH)1 Num 1A Characteristic ECLK Period 2A, 3A ECLK Pulse Width Symbol Min Max Unit tEcyc 555 -- ns tECW 277.5 -- ns E1 ECLK Low to Address Valid2 tEAD -- 70 ns E2 ECLK Low to Address Hold tEAH 10 -- ns E3 ECLK Low to CS Valid (CS delay) tECSD -- 140 ns E4 ECLK Low to CS Hold tECSH 10 -- ns E5 CS Negated Width tECSN 35 -- ns E6 Read Data Setup Time tEDSR 35 -- ns E7 Read Data Hold Time tEDHR 5 -- ns E8 ECLK Low to Data High Impedance tEDHZ -- 130 ns E9 CS Negated to Data Hold (Read) tECDH 0 -- ns E10 CS Negated to Data High Impedance tECDZ -- 1 tcyc E11 ECLK Low to Data Valid (Write) tEDDW -- 2 tcyc E12 ECLK Low to Data Hold (Write) tEDHW 10 -- ns tEACC 450 -- ns (Read)3 E13 Address Access Time E14 Chip Select Access Time (Read)4 tEACS 380 -- ns E15 Address Setup Time tEAS 1/2 -- tcyc NOTES: 1. All AC timing is shown with respect to 20% VDD and 70% VDD levels unless otherwise noted. 2. When the previous bus cycle is not an ECLK cycle, the address may be valid before ECLK goes low. 3. Address access time = tEcyc - tEAD - tEDSR. 4. Chip select access time = tEcyc - tECSD - tEDSR. MC68CK338 MC68CK338TS/D For More Information On This Product, Go to: www.freescale.com MOTOROLA 129 Freescale Semiconductor, Inc. CLKOUT 2A 3A ECLK 1A R/W E1 E2 ADDR[23:0] E3 E14 E6 CS Freescale Semiconductor, Inc... E5 E4 E15 E9 E13 DATA[15:0] READ WRITE E7 E8 E11 DATA[15:0] E10 WRITE E12 68300 E CYCLE TIM Figure 40 ECLK Timing Diagram MOTOROLA 130 For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. Table 74 QSPI Timing (VDD and VDDSYN = 2.7 to 3.6 Vdc, VSS = 0 Vdc, TA = TL to TH 200 pF load on all QSPI pins)1 Freescale Semiconductor, Inc... Num Function Symbol Min Max Unit fop DC DC 1/4 1/4 System Clock Frequency System Clock Frequency 1 Operating Frequency Master Slave 2 Cycle Time Master Slave tqcyc 4 4 510 -- tcyc tcyc 3 Enable Lead Time Master Slave tlead 2 2 128 -- tcyc tcyc 4 Enable Lag Time Master Slave tlag -- 2 1/2 -- SCK tcyc 5 Clock (SCK) High or Low Time Master Slave2 tsw 2 tcyc - 60 2 tcyc - n 255 tcyc -- ns ns 6 Sequential Transfer Delay Master Slave (Does Not Require Deselect) ttd 17 13 8192 -- tcyc tcyc 7 Data Setup Time (Inputs) Master Slave tsu 45 30 -- -- ns ns 8 Data Hold Time (Inputs) Master Slave thi 0 30 -- -- ns ns 9 Slave Access Time ta -- 1 tcyc 10 Slave MISO Disable Time tdis -- 2 tcyc 11 Data Valid (after SCK Edge) Master Slave tv -- -- 75 75 ns ns 12 Data Hold Time (Outputs) Master Slave tho 0 0 -- -- ns ns 13 Rise Time Input Output tri tro -- -- 2 45 s ns 14 Fall Time Input3 Output tfi tfo -- -- 2 45 s ns NOTES: 1. All AC timing is shown with respect to 20% VDD and 70% VDD levels unless otherwise noted. 2. For high time, n = External SCK rise time; for low time, n = External SCK fall time. 3. Data can be recognized properly with longer transition times as long as MOSI/MISO signals from external sources are at valid VOH/VOL prior to SCK transitioning between valid VOL and VOH. Due to process variation, logic decision point voltages of the data and clock signals can differ, which can corrupt data if slower transition times are used. MC68CK338 MC68CK338TS/D For More Information On This Product, Go to: www.freescale.com MOTOROLA 131 Freescale Semiconductor, Inc. 3 2 PCS[3:0] OUTPUT 5 13 12 SCK CPOL=0 OUTPUT 4 1 SCK CPOL=1 OUTPUT 6 12 4 13 7 Freescale Semiconductor, Inc... MISO INPUT MSB IN DATA LSB IN 11 MOSI OUTPUT MSB OUT PD MSB IN 10 DATA LSB OUT PORT DATA 13 MSB OUT 12 QSPI MAST CPHA0 Figure 41 QSPI Timing -- Master, CPHA = 0 3 2 PCS[3:0] OUTPUT 5 13 12 1 SCK CPOL=0 OUTPUT 4 1 7 SCK CPOL=1 OUTPUT 12 4 13 6 MISO INPUT DATA MSB IN 11 MOSI OUTPUT MSB OUT PORT DATA 13 LSB IN MSB 10 DATA LSB OUT PORT DATA MSB 12 QSPI MAST CPHA1 Figure 42 QSPI Timing -- Master, CPHA = 1 MOTOROLA 132 For More Information On This Product, Go to: www.freescale.com MC68CK338 MC68CK338TS/D Freescale Semiconductor, Inc. 3 2 SS INPUT 5 13 12 SCK CPOL=0 INPUT 4 1 SCK CPOL=1 INPUT 12 4 Freescale Semiconductor, Inc... MISO OUTPUT 13 MSB OUT 11 10 11 8 DATA 9 LSB OUT PD MSB OUT 13 7 6 MOSI INPUT MSB IN DATA LSB IN MSB IN QSPI SLV CPHA0 Figure 43 QSPI Timing -- Slave, CPHA = 0 SS INPUT 5 1 13 4 12 SCK CPOL=0 INPUT 4 2 3 SCK CPOL=1 INPUT 12 13 10 10 8 MISO OUTPUT PD MSB OUT 9 11 DATA SLAVE LSB OUT PD 12 7 6 MOSI INPUT MSB IN DATA LSB IN QSPI SLV CPHA1 Figure 44 QSPI Timing -- Slave, CPHA = 1 MC68CK338 MC68CK338TS/D For More Information On This Product, Go to: www.freescale.com MOTOROLA 133