UNISONIC TECHNOLOGIES CO., LTD LR1107/E CMOS IC 600mA FAST ULTRA LOW DROPOUT LINEAR REGULATOR DESCRIPTION The UTC LR1107/E operate from a +2.5V ~ +7.0V input supply as fast ultra low-dropout linear regulators. Wide output voltage range options are available. The fast response characteristic to make UTC LR1107/E suitable for low voltage microprocessor application. The low quiescent current operation and low dropout quality caused by the CMOS process. The UTC LR1107/E has ultra low dropout voltage; 300mV at 600mA load current typically. The ground pin current is typically 200uA at 1mA load current. SET/ADJ Mode (for LR1107): Connect an external resistive voltage-divider from VOUT to this pin to set the output voltage from 1.145V to 5V. ERROR Flag (for LR1107E): When the output voltage drops 10% below nominal value Error flag goes low. Output Voltage Precision: Multiple output voltage options are available and ranging from 1.2V ~ 5.0V at room temperature with a guaranteed accuracy of 1.5%, and 3.0% when varying line, load and temperature. FEATURES * Ultra Low Dropout Voltage * Low Ground Pin Current * 0.68% Load Regulation * The Guaranteed Output Current is 600mA DC * Output Voltage Accuracy 1.5% * ERROR Flag Indicates Output Status * VOUT can be Adjusted From 1.145V to 5V. * Low Output Capacitor Required * Overtemperature Protection and Overcurrent Protection ORDERING INFORMATION Ordering Number Lead Free Halogen Free LR1107L-xx-AA3-A-R LR1107G-xx-AA3-A-R LR1107L-xx-AE3-3-R LR1107G-xx-AE3-3-R LR1107L-xx-AB3-C-R LR1107G-xx-AB3-C-R LR1107L-xx-AB3-D-R LR1107G-xx-AB3-D-R LR1107L-xx-AF5-R LR1107G-xx-AF5-R LR1107EL-xx-AF5-R LR1107EG-xx-AF5-R Note: Pin Assignment: I:VIN O:VOUT G:GND SD: SD Package SOT-223 SOT-23 SOT-89 SOT-89 SOT-25 SOT-25 E: ERROR Pin Assignment 1 2 3 4 5 G O I O G I G I O I G O I G SD S O I G SD E O SSET/ADJ Packing Tape Reel Tape Reel Tape Reel Tape Reel Tape Reel Tape Reel (1) R: Tape Reel LR1107EL-xx-AA3-A-R (1) Packing Type (2) refer to Pin Assignment (2) Pin Assignment (3) AA3: SOT-223, AB3:SOT-89, (3) Package Type (3) AE3:SOT-23, AF5:SOT-25 (4) Voltage Code (4) xx: reference to Marking Information (5) Lead Free (5) G: Halogen Free, L: Lead Free (6) Pin Situation (6) Refer to PIN CONFIGURATION www.unisonic.com.tw Copyright (c) 2013 Unisonic Technologies Co., Ltd 1 of 6 QW-R102-033.I LR1107/E CMOS IC MARKING INFORMATION PACKAGE VOLTAGE CODE MARKING Pin Code SOT-223 L: Lead Free G: Halogen Free Date Code LR1107 Voltage Code 1 2 3 3 SOT-23 Voltage Code 18:1.8V 25:2.5V 28:2.8V 2J:2.85V 33:3.3V ESXX 2 1 Voltage Code ESXX 1 Pin Code Date Code SOT-89 2 L: Lead Free G: Halogen Free 3 LR1107 1 2 3 Voltage Code L: Lead Free G: Halogen Free PIN CONFIGURATION VOUT VOUT ERROR 4 5 5 1 2 3 VIN GND SD SET/ADJ 4 1 2 3 VIN GND SD SOT-25 (for LR1107E) 4 5 SOT-25 L: Lead Free G: Halogen Free SOT-25 (for LR1107) SOT-23 PIN DESCRIPTION PIN NAME VIN GND I/O SD I ERROR (for LR1107E) SET/ADJ (for LR1107) VOUT DESCRIPTION Input supply Ground O O O Shutdown LR1107/E enable; when the SD pin connects to GND will shutdown the LR1107/E; At normal operation, SD must be tied to VDD through a 10K pull up resistor. Error flag, active low; when the output dropout of regulation due to low input voltage, the LR1107E produces a logic low signal at the ERROR pin. Voltage-Setting Input. Connect an external resistive voltage-divider from VOUT to this pin to set the output voltage. Output voltage UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 2 of 6 QW-R102-033.I LR1107/E CMOS IC BLOCK DIAGRAM VIN SD VOUT SET/ADJ 80mV GND LR1107 UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 3 of 6 QW-R102-033.I LR1107/E CMOS IC ABSOLUTE MAXIMUM RATINGS (Note 1) PARAMETER Input Voltage (Operating), (Note 10) Input Voltage (Survival) Shutdown Input Voltage Output Voltage (Survival), (Note 4, 5) IOUT (Survival) SYMBOL VIN VI(SHDN) VOUT RATINGS 2.5~7.0 -0.3~+7.5 -0.3~VIN+0.3 -0.3~+7.5 Short Circuit Protected UNIT V V V V VIN+0.3 V 600 Internally Limited 150 -40~+125 -65~+150 mA Maximum Voltage for ERROR , SET/ADJ Pin Maximum Operating Current (DC) Power Dissipation (Note 2) Junction Temperature Operating Temperature Storage Temperature PD TJ TOPR TSTG C C C ELECTRICAL CHARACTERISTICS Limits in standard typeface are for TJ = 25C, and limits in boldface type apply over the full operating temperature range. (TJ = 25C, VIN = VO(NOM) + 1V, IL = 10 mA, COUT = 22F, VSD = VIN-0.3V, unless otherwise specified.) TYP PARAMETER SYMBOL TEST CONDITIONS MIN MAX UNIT (Note 3) Output Voltage Tolerance (Note 6) Output Voltage Line Regulation (Note 6) Output Voltage Load Regulation (Note 6) Dropout Voltage (Note 8) Ground Pin Current In Normal Operation Mode Ground Pin Current In Shutdown Mode Peak Output Current SHORT CIRCUIT PROTECTION Short Circuit Current OVER TEMPERATURE PROTECTION Shutdown Threshold Thermal Shutdown Hysteresis SHUTDOWN INPUT VOUT VOUT VOUT VD IGND1 IGND2 IO(PEAK) -1.5 -3 0 +1.5 +3 0.725 10 mA < IL < 600mA 0.68 IL = 600mA IL = 0 mA IL = 600mA VSD0.2V (Note 9) (Note 2) 300 200 300 0.02 800 600 % % % 500 mV A 5 A mA ISC 2 A TSHDN(THR) TSHDN(HYS) 165 10 C C Shutdown Threshold VSHDN Turn-off Delay Turn-on Delay tD(OFF) tD(ON) SD Input Current 0 mA IL 600mA VOUT +1 VIN 7.0V VOUT+1V<VIN<7.0V ISD Output = High Output = Low IL = 600mA IL = 600mA VSD = VIN UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw VIN-0.3 VIN 0 20 60 1 0.2 V V s s nA 4 of 6 QW-R102-033.I LR1107/E CMOS IC ELECTRICAL CHARACTERISTICS(Cont.) PARAMETER SYMBOL TEST CONDITIONS MIN TYP (Note 3) MAX UNIT 0.1 V ERROR FLAG COMPARATOR (for LR1107E) ERROR Flag Saturation VEF(SAT) ERROR Flag Pin Leakage Current II(LEAK) Threshold Threshold Hysteresis Flag Reset Delay SET/ADJ Mode (for LR1107 5pins) VT VTHR tD SET Voltage VSET ISINK = 100A 0.02 1 (Note 7) (Note 7) Measured on ADJ, IOUT =10mA nA 5 2 7 4.2 17 16 8 % % s 1.110 1.145 1.188 V AC PARAMETERS Ripple Rejection Output Noise Density Output Noise Voltage PSRR n(l/f) eN VIN = VOUT + 1.5V COUT=100uF, VOUT = 3.3V VIN = VOUT + 0.3V COUT=100uF, VOUT = 3.3V f = 120Hz BW = 10Hz - 100kHz 60 dB 40 dB 0.8 150 V Vrms Note 1. Absolute maximum ratings are those values beyond which the device could be permanently damaged. Absolute maximum ratings are stress ratings only and functional device operation is not implied. Conditions for which the device is intended to be functional is indicated by operating ratings, but specific performance limits isn't be guaranteed. To make sure of specifications and test conditions, read Electrical Characteristics. Only for the test conditions listed the guaranteed specifications can be applied. When the device is not operated under the listed test conditions some performance characteristics may degrade. 2. Devices must be derated based on package thermal resistance at elevated temperatures. 3. The most likely parametric norm represents at 25C. 4. The LR1107/E output must be diode-clamped to ground. If used in a dual-supply system where the regulator load is returned to a negative supply. 5. Between the VIN and VOUT terminals the output PMOS structure contains a diode. This diode is reverse biased normally. If the voltage at the output terminal is forced to be higher than the voltage at the input terminal this diode will get forward biased. This diode can withstand 650mA of peak current and 120mA of DC current typically. 6. Output voltage line regulation is the change in output voltage from the nominal value which is due to change in the input line voltage. Which is defined as the change in output voltage from the nominal value due to change in load current is output voltage load regulation. The load regulation and line regulation specification include the typical number only. But, the limits for load and line regulation are included in the output voltage tolerance specification. 7. ERROR Flag hysteresis and threshold are specified as regulated output voltage's percentage. 8. At which the output drops 2% below the normal value dropout voltage is defined as the minimum input to output differential voltage. Only to output voltages of 2.5V and above dropout voltage specification applies. For output voltages below 2.5V, since the minimum input voltage is 2.5V, the drop-out voltage is nothing but the input to output differential. 9. Specification has been tested at -40CTJ 85C cause under shutdown conditions the temperature rise of the device is negligible. 10. The minimum operating VIN value is equal to VOUT(NOM) + VDROPOUT] or 2.5V, just the greater. UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 5 of 6 QW-R102-033.I LR1107/E CMOS IC TYPICAL APPLICATION CIRCUIT INPUT 3.3V10% CIN 1F SD (NOTE) VIN VOUT SD UTC LR1107E ERROR VOUT 2.5V, 500mA ERROR (NOTE) COUT 22F GND Note: SD and ERROR pins must be pulled high through a 10k pull-up resistor. Connect the ERROR pin to ground if this function is not used. INPUT 3.3V10% CIN 1F SD (NOTE) VIN VOUT SD UTC LR1107 SET/ADJ VOUT 2.5V, 500mA COUT 22F GND Note: SD pins must be pulled high through a 10k pull-up resistor. Connect the SET/ADJ pin to ground if this function is not used. UTC assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all UTC products described or contained herein. UTC products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 6 of 6 QW-R102-033.I