ADC0844, ADC0848 www.ti.com SNAS523D - JUNE 1999 - REVISED MARCH 2013 ADC0844/ADC0848 8-Bit P Compatible A/D Converters with Multiplexer Options Check for Samples: ADC0844, ADC0848 FEATURES DESCRIPTION * * The ADC0844 and ADC0848 are CMOS 8-bit successive approximation A/D converters with versatile analog input multiplexers. The 4-channel or 8-channel multiplexers can be software configured for single-ended, differential or pseudo-differential modes of operation. 1 2 * * * * * * Easy Interface to All Microprocessors Operates Ratiometrically or with 5 VDC Voltage Reference No Zero or Full-Scale Adjust Required 4-Channel or 8-Channel Multiplexer with Address Logic Internal Clock 0V to 5V Input Range with Single 5V Power Supply Standard Width 20-Pin or 24-Pin PDIP 28 Pin PLCC Package KEY SPECIFICATIONS * * * * * Resolution: 8 Bits Total Unadjusted Error: 1/2 LSB and 1 LSB Single Supply: 5 VDC Low Power: 15 mW Conversion Time: 40 s The differential mode provides low frequency input common mode rejection and allows offsetting the analog range of the converter. In addition, the A/D's reference can be adjusted enabling the conversion of reduced analog ranges with 8-bit resolution. The A/Ds are designed to operate from the control bus of a wide variety of microprocessors. TRI-STATE output latches that directly drive the data bus permit the A/Ds to be configured as memory locations or I/O devices to the microprocessor with no interface logic necessary. Block Diagram * ADC0848 shown in PDIP Package CH5-CH8 not included on the ADC0844 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 1999-2013, Texas Instruments Incorporated ADC0844, ADC0848 SNAS523D - JUNE 1999 - REVISED MARCH 2013 www.ti.com Connection Diagram Figure 1. PLCC Package (Top View) Figure 2. 20-Pin PDIP (Top View) Figure 3. 28-Pin PDIP (Top View) These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. Absolute Maximum Ratings (1) (2) (3) Supply Voltage (VCC) 6.5V -0.3V to +15V Logic Control Inputs Voltage -0.3V to VCC+0.3V At Other Inputs and Outputs Input Current at Any Pin (4) Package Input Current 5 mA (4) 20 mA -65C to +150C Storage Temperature Package Dissipation at TA=25C ESD Susceptibility 875 mW (5) 800V PDIP Package Lead Temperature (Soldering, 10 seconds) (1) (2) (3) (4) (5) 2 PLCC Package 260C Vapor Phase (60 seconds) 215C Infrared (15 seconds) 220C Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. DC and AC electrical specifications do not apply when operating the device beyond its specified operating conditions. All voltages are measured with respect to the ground pins. If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and specifications. When the input voltage (VIN) at any pin exceeds the power supply rails (VIN < V-or VIN > V+) the absolute value of the current at that pin should be limited to 5 mA or less. The 20 mA package input current limits the number of pins that can exceed the power supply boundaries with a 5 mA current limit to four. Human body model, 100 pF discharged through a 1.5 k resistor. Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: ADC0844 ADC0848 ADC0844, ADC0848 www.ti.com SNAS523D - JUNE 1999 - REVISED MARCH 2013 Operating Conditions (1) (2) Supply Voltage (VCC) 4.5 VDC to 6.0 VDC 0CTA70C ADC0844CCN, ADC0848BCN, ADC0848CCN Temperature Range (TMINTATMAX) (1) (2) (3) ADC0844BCJ (3), ADC0844CCJ (3), ADC0848BCV, ADC0848CCV -40CTA85C Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. DC and AC electrical specifications do not apply when operating the device beyond its specified operating conditions. All voltages are measured with respect to the ground pins. Product/package combination obsolete; shown for reference only. Electrical Characteristics The following specifications apply for VCC = 5 VDC unless otherwise specified. Boldface limits apply from TMIN to TMAX; all other limits TA = Tj = 25C. Parameter Conditions ADC0844CCN, ADC0848BCN, ADC0848CCN, ADC0848BCV, ADC0848CCV ADC0844BCJ (1) ADC0844CCJ (1) Typ (2) Tested Design Limit (3) Limit (4) Typ (2) Limit Units Tested Design Limit (3) Limit (4) CONVERTER AND MULTIPLEXER CHARACTERISTICS Maximum Total ADC0844BCN, ADC0848BCN, BCV Unadjusted Error ADC0844CCN, ADC0848CCN, CCV 1/2 1/2 LSB 1 1 LSB VREF = 5.00 VDC (5) ADC0844CCJ (1) 1 LSB Minimum Reference Input Resistance 2.4 1.1 2.4 1.2 1.1 k Maximum Reference Input Resistance 2.4 5.9 2.4 5.4 5.9 k VCC + 0.05 VCC + 0.05 V GND - 0.05 GND - 0.05 V Maximum Common-Mode Input Voltage See (6) VCC + 0.05 Minimum Common-Mode Input Voltage See (6) GND - 0.05 DC Common-Mode Error Differential Mode 1/16 1/4 1/16 1/4 1/4 LSB Power Supply Sensitivity VCC = 5V5% 1/16 1/16 LSB Off Channel Leakage Current On Channel = 5V, Off Channel = 0V (7) -1 -0.1 -1 A On Channel = 0V, Off Channel = 5V 1 0.1 1 A 2.0 2.0 2.0 V 0.8 DIGITAL AND DC CHARACTERISTICS VIN(1), Logical "1" Input Voltage (Min) VCC = 5.25V VIN(0), Logical "0" Input Voltage (Max) VCC = 4.75V 0.8 V IIN(1), Logical "1" Input Current (Max) VIN = 5.0V 0.005 1 0.005 1 A IIN(0), Logical "0" Input Current (Max) VIN = 0V -0.005 -1 -0.005 -1 A (1) (2) (3) (4) (5) (6) (7) 0.8 This product/package combination is obsolete. Shown for reference only. Typical figures are at 25C and represent most likely parametric norm. Tested limits are specified to TI's AOQL (Average Outgoing Quality Level). Design limits are specified by not 100% tested. These limits are not used to calculate outgoing quality levels. Total unadjusted error includes offset, full-scale, linearity, and multiplexer error. For VIN (-) VIN(+) the digital output code will be 0000 0000. Two on-chip diodes are tied to each analog input, which will forwardconduct for analog input voltages one diode drop below ground or one diode drop greater than VCC supply. Be careful during testing at low VCC levels (4.5V), as high level analog inputs (5V) can cause this input diode to conduct, especially at elevated temperatures, and cause errors for analog inputs near full-scale. The spec allows 50 mV forward bias of either diode. This means that as long as the analog VIN does not exceed the supply voltage by more than 50 mV, the output code will be correct. To achieve an absolute 0 VDC to 5 VDC input voltage range will therefore require a minimum supply voltage of 4.950 VDC over temperature variations, initial tolerance and loading. Off channel leakage current is measured after the channel selection. Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: ADC0844 ADC0848 Submit Documentation Feedback 3 ADC0844, ADC0848 SNAS523D - JUNE 1999 - REVISED MARCH 2013 www.ti.com Electrical Characteristics (continued) The following specifications apply for VCC = 5 VDC unless otherwise specified. Boldface limits apply from TMIN to TMAX; all other limits TA = Tj = 25C. Parameter Conditions Typ (2) VOUT(1), Logical "1" Output Voltage (Min) VOUT(0), Logical "0" Output Voltage (Max) ADC0844CCN, ADC0848BCN, ADC0848CCN, ADC0848BCV, ADC0848CCV ADC0844BCJ (1) ADC0844CCJ (1) Tested Design Limit (3) Limit (4) Limit Units Tested Design Limit (3) Limit (4) Typ (2) VCC = 4.75V, IOUT = -360 A 2.4 2.8 2.4 V IOUT = -10 A 4.5 4.6 4.5 V VCC = 4.75V, IOUT = 1.6 mA 0.4 0.34 0.4 V A VOUT = 0V -0.01 -3 -0.01 -0.3 -3 VOUT = 5V 0.01 3 0.01 0.3 3 A ISOURCE, Output Source Current (Min) VOUT = 0V -14 -6.5 -14 -7.5 -6.5 mA ISINK, Output Sink Current (Min) VOUT = VCC 16 8.0 16 9.0 8.0 mA ICC, Supply Current (Max) CS = 1, VREF Open 1 2.5 1 2.3 2.5 mA IOUT, TRI-STATE Output Current (Max) AC Electrical Characteristics The following specifications apply for VCC = 5VDC, tr = tf = 10 ns unless otherwise specified. Boldface limits apply from TMIN to TMAX; all other limits TA = Tj = 25C. Parameter Typ (1) Conditions tC, Maximum Conversion Time (See Figure 7) Tested Limit (2) Design Limit (3) Units 60 s 30 40 tW(WR), Minimum WR Pulse Width See (4) 50 150 tACC, Maximum Access Time (Delay from Falling Edge of RD to Output Data Valid) CL = 100 pF (4) 145 225 ns t1H, t0H, TRI-STATE Control (Maximum Delay from Rising Edge of RD to Hi-Z State) CL = 10 pF, RL = 10k (4) 125 200 ns tWI, tRI, Maximum Delay from Falling Edge of WR or RD to Reset of INTR tDS, Minimum Data Set-Up Time See (4) ns 200 400 ns 50 100 ns tDH, Minimum Data Hold Time 0 50 ns CIN, Capacitance of Logic Inputs 5 pF COUT, Capacitance of Logic Outputs 5 pF (1) (2) (3) (4) 4 Typical figures are at 25C and represent most likely parametric norm. Tested limits are specified to TI's AOQL (Average Outgoing Quality Level). Design limits are specified by not 100% tested. These limits are not used to calculate outgoing quality levels. The temperature coefficient is 0.3%/C. Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: ADC0844 ADC0848 ADC0844, ADC0848 www.ti.com SNAS523D - JUNE 1999 - REVISED MARCH 2013 Typical Performance Characteristics Logic Input Threshold Voltage vs. Supply Voltage Output Current vs. Temperature Figure 4. Figure 5. Power Supply Current vs. Temperature Linearity Error vs. VREF Figure 6. Figure 7. Conversion Time vs. VSUPPLY Conversion Time vs.Temperature Figure 8. Figure 9. Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: ADC0844 ADC0848 Submit Documentation Feedback 5 ADC0844, ADC0848 SNAS523D - JUNE 1999 - REVISED MARCH 2013 www.ti.com Typical Performance Characteristics (continued) Unadjusted Offset Error vs. VREF Voltage Figure 10. TRI-STATE Test Circuits and Waveforms t1H t1H, CL = 10 pF t0H t0H, CL = 10 pF tr = 20 ns Leakage Current Test Circuit 6 Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: ADC0844 ADC0848 ADC0844, ADC0848 www.ti.com SNAS523D - JUNE 1999 - REVISED MARCH 2013 Timing Diagrams Read strobe must occur at least 600 ns after the assertion of interrupt to ensure reset of INTR . MA stands for MUX address. Figure 11. Using the Previously Selected Channel Configuration and Starting a Conversion Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: ADC0844 ADC0848 Submit Documentation Feedback 7 ADC0844, ADC0848 SNAS523D - JUNE 1999 - REVISED MARCH 2013 www.ti.com ADC0848 Functional Block Diagram 8 Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: ADC0844 ADC0848 ADC0844, ADC0848 www.ti.com SNAS523D - JUNE 1999 - REVISED MARCH 2013 Functional Description The ADC0844 and ADC0848 contain a 4-channel and 8-channel analog input multiplexer (MUX) respectively. Each MUX can be configured into one of three modes of operation differential, pseudo-differential, and single ended. These modes are discussed in Applications Information. The specific mode is selected by loading the MUX address latch with the proper address (see Table 1 and Table 2). Inputs to the MUX address latch (MA0MA4) are common with data bus lines (DB0-DB4) and are enabled when the RD line is high. A conversion is initiated via the CS and WR lines. If the data from a previous conversion is not read, the INTR line will be low. The falling edge of WR will reset the INTR line high and ready the A/D for a conversion cycle. The rising edge of WR, with RD high, strobes the data on the MA0/DB0-MA4/DB4 inputs into the MUX address latch to select a new input configuration and start a conversion. If the RD line is held low during the entire low period of WR the previous MUX configuration is retained, and the data of the previous conversion is the output on lines DB0-DB7. After the conversion cycle (tC 40 s), which is set by the internal clock frequency, the digital data is transferred to the output latch and the INTR is asserted low. Taking CS and RD low resets INTR output high and outputs the conversion result on the data lines (DB0-DB7). APPLICATIONS INFORMATION MULTIPLEXER CONFIGURATION The design of these converters utilizes a sampled-data comparator structure which allows a differential analog input to be converted by a successive approximation routine. The actual voltage converted is always the difference between an assigned "+" input terminal and a "-" input terminal. The polarity of each input terminal of the pair being converted indicates which line the converter expects to be the most positive. If the assigned "+" input is less than the "-" input the converter responds with an all zeros output code. A unique input multiplexing scheme has been utilized to provide multiple analog channels. The input channels can be software configured into three modes: differential, single ended, or pseudo-differential. Figure 12 shows the three modes using the 4-channel MUX ADC0844. The eight inputs of the ADC0848 can also be configured in any of the three modes. In the differential mode, the ADC0844 channel inputs are grouped in pairs, CH1 with CH2 and CH3 with CH4. The polarity assignment of each channel in the pair is interchangeable. The singleended mode has CH1-CH4 assigned as the positive input with the negative input being the analog ground (AGND) of the device. Finally, in the pseudo-differential mode CH1-CH3 are positive inputs referenced to CH4 which is now a pseudo-ground. This pseudo-ground input can be set to any potential within the input commonmode range of the converter. The analog signal conditioning required in transducer-based data acquisition systems is significantly simplified with this type of input flexibility. One converter package can now handle ground referenced inputs and true differential inputs as well as signals with some arbitrary reference voltage. The analog input voltages for each channel can range from 50 mV below ground to 50 mV above VCC (typically 5V) without degrading conversion accuracy. Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: ADC0844 ADC0848 Submit Documentation Feedback 9 ADC0844, ADC0848 SNAS523D - JUNE 1999 - REVISED MARCH 2013 www.ti.com Table 1. ADC0844 MUX ADDRESSING (1) MUX Address CS RD MA2 MA1 X L L L L X L L H L X L H L L X L H H L L H L L L L H L H L L H H L L H (1) MA0 WR MA3 NP CH2 CH3 CH4 H + - H - H + + - H - + H NP L H H H L H H L L L H H H L H L H H H L L X X X X L H L MUX Mode Differential - + - + + Single-Ended - - + - + H NP AGND - + H H NP Channel# CH1 + Pseudo- Differential - Previous Channel Configuration X = don't care, NP = negative pulse 4 Single-Ended 2 Differential 3 Pseudo-Differential Combined Figure 12. Analog Input Multiplexer Options REFERENCE CONSIDERATIONS The voltage applied to the reference input of these converters defines the voltage span of the analog input (the difference between VIN(MAX) and VIN(MIN)) over which the 256 possible output codes apply. The devices can be used in either ratiometric applications or in systems requiring absolute accuracy. The reference pin must be connected to a voltage source capable of driving the minimum reference input resistance of 1.1 k. This pin is the top of a resistor divider string used for the successive approximation conversion. In a ratiometric system (Figure 13), the analog input voltage is proportional to the voltage used for the A/D reference. This voltage is typically the system power supply, so the VREF pin can be tied to VCC. This technique relaxes the stability requirements of the system reference as the analog input and A/D reference move together maintaining the same output code for a given input condition. For absolute accuracy (Figure 14), where the analog input varies between very specific voltage limits, the reference pin can be biased with a time and temperature stable voltage source. The LM385 and LM336 reference diodes are good low current devices to use with these converters. The maximum value of the reference is limited to the VCC supply voltage. The minimum value, however, can be quite small (see Typical Performance Characteristics) to allow direct conversions of transducer outputs providing less than a 5V output span. Particular care must be taken with regard to noise pickup, circuit layout and system error voltage sources when operating with a reduced span due to the increased sensitivity of the converter (1 LSB equals VREF/256). 10 Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: ADC0844 ADC0848 ADC0844, ADC0848 www.ti.com SNAS523D - JUNE 1999 - REVISED MARCH 2013 THE ANALOG INPUTS Analog Differential Voltage Inputs and Common-Mode Rejection The differential input of these converters actually reduces the effects of common-mode input noise, a signal common to both selected "+" and "-" inputs for a conversion (60 Hz is most typical). The time interval between sampling the "+" input and then the "-" inputs is 1/2 of a clock period. The change in the common-mode voltage during this short time interval can cause conversion errors. For a sinusoidal common-mode signal this error is: where * * * fCM is the frequency of the common-mode signal Vpeak is its peak voltage value tC is the conversion time For a 60 Hz common-mode signal to generate a 1/4 LSB error (5 mV) with the converter running at 40 S, its peak value would have to be 5.43V. This large a common-mode signal is much greater than that generally found in a well designed data acquisition system. Table 2. ADC0848 MUX Addressing (1) MUX Address MA3 MA2 MA1 X L L L L L X L L L H L X L L H L L X L L H H L X L H L L L X L H L H X L H H L X L H H L H L L H L L H L (1) MA0 CS MA4 WR RD Channel CH5 CH6 H + - L H - + L H + - H L H - + L L L H L H L H L H L L H H L H H L L H H L L L H L H H L H L H L H H H L L H NP NP CH1 CH2 CH3 CH4 H + - H - + H + - H - + L H H H H L H H L L L L H H H L L H L H H H L H L L H H L H H L H H H L L L H H H H L H L H H H H H L L H X X X X X L L H NP H CH8 AGND MUX Mode Differential - + - + - + H H CH7 - + - + Single-Ended - + - + + - - + - + - + - + PseudoDifferential - + - + + - Previous Channel Configuration X = don't care, NP = negative pulse Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: ADC0844 ADC0848 Submit Documentation Feedback 11 ADC0844, ADC0848 SNAS523D - JUNE 1999 - REVISED MARCH 2013 www.ti.com Input Current Due to the sampling nature of the analog inputs, short duration spikes of current enter the "+" input and exit the "-" input at the clock edges during the actual conversion. These currents decay rapidly and do not cause errors as the internal comparator is strobed at the end of a clock period. Bypass capacitors at the inputs will average these currents and cause an effective DC current to flow through the output resistance of the analog signal source. Bypass capacitors should not be used if the source resistance is greater than 1 k. Input Source Resistance The limitation of the input source resistance due to the DC leakage currents of the input multiplexer is important. A worst-case leakage current of 1 A over temperature will create a 1 mV input error with a 1 k source resistance. An op amp RC active low pass filter can provide both impedance buffering and noise filtering should a high impedance signal source be required. OPTIONAL ADJUSTMENTS Zero Error The zero of the A/D does not require adjustment. If the minimum analog input voltage value, VIN(MIN), is not ground, a zero offset can be done. The converter can be made to output 0000 0000 digital code for this minimum input voltage by biasing any VIN (-) input at this VIN(MIN) value. This is useful for either differential or pseudodifferential modes of input channel configuration. The zero error of the A/D converter relates to the location of the first riser of the transfer function and can be measured by grounding the V- input and applying a small magnitude positive voltage to the V+ input. Zero error is the difference between actual DC input voltage which is necessary to just cause an output digital code transition from 0000 0000 to 0000 0001 and the ideal 1/2 LSB value (1/2 LSB=9.8 mV for VREF=5.000 VDC). Full-Scale The full-scale adjustment can be made by applying a differential input voltage which is 1 1/2 LSB down from the desired analog full-scale voltage range and then adjusting the magnitude of the VREF input for a digital output code changing from 1111 1110 to 1111 1111. Adjusting for an Arbitrary Analog Input Voltage Range If the analog zero voltage of the A/D is shifted away from ground (for example, to accommodate an analog input signal which does not go to ground), this new zero reference should be properly adjusted first. A VIN (+) voltage which equals this desired zero reference plus 1/2 LSB (where the LSB is calculated for the desired analog span, 1 LSB = analog span/256) is applied to selected "+" input and the zero reference voltage at the corresponding "-" input should then be adjusted to just obtain the 00HEX to 01HEX code transition. Figure 13. Referencing Examples - Ratiometric 12 Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: ADC0844 ADC0848 ADC0844, ADC0848 www.ti.com SNAS523D - JUNE 1999 - REVISED MARCH 2013 Figure 14. Referencing Examples - Absolute with a Reduced Span The full-scale adjustment should be made [with the proper VIN (-) voltage applied] by forcing a voltage to the VIN (+) input which is given by: where * * VMAX = the high end of the analog input range VMIN = the low end (the offset zero) of the analog range. (Both are ground referenced.) (1) The VREF (or VCC) voltage is then adjusted to provide a code change from FEHEX to FFHEX. This completes the adjustment procedure. For an example see the Zero-Shift and Span Adjust circuit below. Figure 15. Zero-Shift and Span Adjust (2V VIN 5V) Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: ADC0844 ADC0848 Submit Documentation Feedback 13 ADC0844, ADC0848 SNAS523D - JUNE 1999 - REVISED MARCH 2013 www.ti.com Figure 16. Differential Voltage Input 9-Bit A/D Figure 17. Span Adjust (0V VIN 3V) Diodes are 1N914 DO = all 1s if VIN(+)>VIN(-) DO = all 0s if VIN(+)<VIN(-) Figure 18. Protecting the Input Figure 19. High Accuracy Comparators * VIN(-)=0.15 VCC 15% of VCCVXDR85% of VCC Figure 20. Operating with Automotive Ratiometric Transducers 14 Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: ADC0844 ADC0848 ADC0844, ADC0848 www.ti.com SNAS523D - JUNE 1999 - REVISED MARCH 2013 Note: DUT pin numbers in parentheses are for ADC0844, others are for ADC0848. Figure 21. A Stand Alone Circuit CS *WR will update the channel configuration and start a conversion. CS *RD will read the conversion data and start a new conversion without updating the channel configuration. Waiting for the end of this conversion is not necessary. A CS *WR can immediately follow the CS*RD . Figure 22. Start a Conversion without Updating the Channel Configuration Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: ADC0844 ADC0848 Submit Documentation Feedback 15 ADC0844, ADC0848 SNAS523D - JUNE 1999 - REVISED MARCH 2013 www.ti.com Figure 23. ADC0844--INS8039 Interface Sample Program for ADC0844 - INS8039 Interface Converting Two Ratiometric Differential Signals ORG JMP ORG MOV 0H BEGIN 10H R1,#0FFH B8 20 89 FF 23 00 MOV ORL MOV R0,#20H P1,#0FFH A,00H 0018 001A 14 50 23 02 CALL MOV CONV A,#02H 001C 001D 18 14 50 INC CALL R0 CONV 0000 04 10 0010 B9 FF 0012 0014 0016 BEGIN: ;START PROGRAM AT ADDR 10 ;MAIN PROGRAM ;LOAD R1 WITH AN UNUSED ADDR ;LOCATION ;A/D DATA ADDRESS ;SET PORT 1 OUTPUTS HIGH ;LOAD THE ACC WITH A/D MUX DATA ;CH1 AND CH2 DIFFERENTIAL ;CALL THE CONVERSION SUBROUTINE ;LOAD THE ACC WITH A/D MUX DATA ;CH3 AND CH4 DIFFERENTIAL ;INCREMENT THE A/D DATA ADDRESS ;CALL THE CONVERSION SUBROUTINE ;CONTINUE MAIN PROGRAM ;CONVERSION SUBROUTINE ;ENTRY:ACC-A/D MUX DATA ;EXIT:ACC-CONVERTED DATA 0050 0052 0053 0054 0056 0057 0059 005A 16 99 FE 91 09 32 53 81 89 01 A0 83 CONV: LOOP: ORG ANL MOVX IN JB1 MOVX ORL MOV RET Submit Documentation Feedback 50H P1#0FEH @R1,A A,P1 LOOP A,@R1 P1,&01H @R0,A ;CHIP SELECT THE A/D ;LOAD A/D MUX & START CONVERSION ;INPUT INTR STATE ;IF INTR = 1 GOTO LOOP ;IF INTR = 0 INPUT A/D DATA ;CLEAR THE A/D CHIP SELECT ;STORE THE A/D DATA ;RETURN TO MAIN PROGRAM Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: ADC0844 ADC0848 ADC0844, ADC0848 www.ti.com SNAS523D - JUNE 1999 - REVISED MARCH 2013 Figure 24. I/O Interface to NSC800 Sample Program for ADC0848 - NSC800 Interface 0008 000F 001F 3C00 0000' 0004' 0008' 000A' 000C' 000F' 0012' 08 0C 0E 06 21 11 ED 09 0A 0B 0D 0E 0F 1F 16 0000' 003C A3 0014' EB 0015' 0017' 0018' 001B' 3E 0F 3D C2 0013' ED A2 001D' 001E' EB C2 000E' NCONV DEL CS ADDTA EQU EQU EQU EQU 16 15 1FH 003CH MUXDTA: DB DB LD LD LD LD OUTI 08H,09H,0AH,0BH 0CH,0DH,0EH,0FH C,CS B,NCONV HL,MUXDTA DE,ADDTA EX DE,HL LD DEC JP INI A,DEL A NZ,WAIT EX JP DE,HL NZ,STCONV START: STCONV: WAIT: ;DELAY 50 SEC CONVERSION ;THE BOARD ADDRESS ;START OF RAM FOR A/D ;DATA ;MUX DATA ;LOAD A/D'S MUX DATA ;AND START A CONVERSION ;HL=RAM ADDRESS FOR THE ;A/D DATA ;WAIT 50 SEC FOR THE ;CONVERSION TO FINISH ;STORE THE A/D'S DATA ;CONVERTED ALL INPUTS? ;IF NOT GOTO STCONV END Note: This routine sequentially programs the MUX data latch in the signal-ended mode. For CH1-CH8 a conversion is started, then a 50 s wait for the A/D to complete a conversion and the data is stored at address ADDTA for CH1, ADDTA + 1 for CH2, etc. Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: ADC0844 ADC0848 Submit Documentation Feedback 17 ADC0844, ADC0848 SNAS523D - JUNE 1999 - REVISED MARCH 2013 www.ti.com REVISION HISTORY Changes from Revision C (March 2013) to Revision D * 18 Page Changed layout of National Data Sheet to TI format .......................................................................................................... 17 Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: ADC0844 ADC0848 PACKAGE OPTION ADDENDUM www.ti.com 1-Nov-2013 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (C) Device Marking (4/5) ADC0844CCN NRND PDIP NFH 20 18 TBD Call TI Call TI 0 to 70 ADC0844CCN ADC0844CCN/NOPB ACTIVE PDIP NFH 20 18 Green (RoHS & no Sb/Br) SN Level-1-NA-UNLIM 0 to 70 ADC0844CCN ADC0848BCV NRND PLCC FN 28 35 TBD Call TI Call TI -40 to 85 ADC0848 BCV ADC0848BCV/NOPB ACTIVE PLCC FN 28 35 Green (RoHS & no Sb/Br) SN Level-2A-245C-4 WEEK -40 to 85 ADC0848 BCV ADC0848BCVX/NOPB ACTIVE PLCC FN 28 750 Green (RoHS & no Sb/Br) SN Level-2A-245C-4 WEEK -40 to 85 ADC0848 BCV ADC0848CCN NRND PDIP NAM 24 15 TBD Call TI Call TI -40 to 85 ADC0848CCN ADC0848CCN/NOPB ACTIVE PDIP NAM 24 15 Pb-Free (RoHS) Call TI Level-1-NA-UNLIM -40 to 85 ADC0848CCN ADC0848CCV NRND PLCC FN 28 35 TBD Call TI Call TI -40 to 85 ADC0848 CCV ADC0848CCV/NOPB ACTIVE PLCC FN 28 35 Green (RoHS & no Sb/Br) SN Level-2A-245C-4 WEEK -40 to 85 ADC0848 CCV ADC0848CCVX NRND PLCC FN 28 750 TBD Call TI Call TI -40 to 85 ADC0848 CCV ADC0848CCVX/NOPB ACTIVE PLCC FN 28 750 Green (RoHS & no Sb/Br) SN Level-2A-245C-4 WEEK -40 to 85 ADC0848 CCV (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 1-Nov-2013 Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 MECHANICAL DATA NAM0024D www.ti.com MECHANICAL DATA NFH0020A N0020A N20A (Rev G) www.ti.com MECHANICAL DATA MPLC004A - OCTOBER 1994 FN (S-PQCC-J**) PLASTIC J-LEADED CHIP CARRIER 20 PIN SHOWN Seating Plane 0.004 (0,10) 0.180 (4,57) MAX 0.120 (3,05) 0.090 (2,29) D D1 0.020 (0,51) MIN 3 1 19 0.032 (0,81) 0.026 (0,66) 4 E 18 D2 / E2 E1 D2 / E2 8 14 0.021 (0,53) 0.013 (0,33) 0.007 (0,18) M 0.050 (1,27) 9 13 0.008 (0,20) NOM D/E D2 / E2 D1 / E1 NO. OF PINS ** MIN MAX MIN MAX MIN MAX 20 0.385 (9,78) 0.395 (10,03) 0.350 (8,89) 0.356 (9,04) 0.141 (3,58) 0.169 (4,29) 28 0.485 (12,32) 0.495 (12,57) 0.450 (11,43) 0.456 (11,58) 0.191 (4,85) 0.219 (5,56) 44 0.685 (17,40) 0.695 (17,65) 0.650 (16,51) 0.656 (16,66) 0.291 (7,39) 0.319 (8,10) 52 0.785 (19,94) 0.795 (20,19) 0.750 (19,05) 0.756 (19,20) 0.341 (8,66) 0.369 (9,37) 68 0.985 (25,02) 0.995 (25,27) 0.950 (24,13) 0.958 (24,33) 0.441 (11,20) 0.469 (11,91) 84 1.185 (30,10) 1.195 (30,35) 1.150 (29,21) 1.158 (29,41) 0.541 (13,74) 0.569 (14,45) 4040005 / B 03/95 NOTES: A. All linear dimensions are in inches (millimeters). B. This drawing is subject to change without notice. C. Falls within JEDEC MS-018 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 1 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2013, Texas Instruments Incorporated