MP6-2U-2U-LLE-00 - Artesyn Embedded Technologies

Rev. 07.19.11_89

MP Series

1 of 8

313

process

yellow

3405

1797

1375

116

2607

652

242

2985

375

240

Embedded Power for

Business-Critical Continuity

Electrical Specifications

Input

Input ra nge: 85 - 264 Vac

120 - 350 Vdc

Frequency: 47 - 440 Hz

Inrush current: 40 A peak max. (soft start)

Efficiency: 70 - 80% typ. @ full case load

Power Factor: 0.99 typ. meets EN61000-3-2

Turn-on time: AC on 1.5 sec typ.

inhibit/enable 150 ms typ.

EMI filter standard: CISPR 22/EN55022 Level “B”

EMI filter (low leakage

option):

CISPR 22/EN55022 Level “A”

Leakage current standard: 2.0 mA max. @240 Vac

Leakage current (low leak-

age option):

300µA max. @ 240 Vac

Radiated EMI: CISPR 22/EN55022 Level “B”

Holdover storage: 20 ms minimum (independent of input Vac)

AC OK: >5 ms early warning min. before outputs lose regulation

Full cycle ride thru (50 Hz)

Harmonic distortion: Meets EN61000-3-2

Isolation: Meets EN60950

Global Inhibit/Enable: TTL, Logic “1” and Logic “0”

Input fuse (internal): MP4: 10 A; MP6: 15 A; MP8: 20 A; MP1: 20 A

Warranty: 2 years

MP Series

400 - 1200 Watts

Special Features

• Currentshareonalloutputswith

ratings of 10 A or greater

• Remotesenseonalloutputswith

ratings greater than 2 A

• Overloadprotectiononalloutputs

• Voltageadjustmentonalloutputs

• Marginingonallsingleoutputmodules

• InputOKsignalandstatusindicator

LED

• GlobalDCOKsignalandstatus

indicator LED

• Globalandindividualmoduleinhibits/

enable

• 2yearwarranty

• Forcedaircooling,fieldreplaceablefan

• Isolated5Vbiasvoltage

• Powerfactorcorrection

• EN61000-3-2harmonicdistortion

compliance

• CISPR22,EN55022CurveBconducted

/ radiated EMI

• EuropeanCEMarkrequirements

• OptionalVMEtimingandsystemDC

OK module

• Customer-providedairoption

• Additional200Woutput@highline

(180-264 VAC)

• Lowleakageoptionformedical

applications

• EN61000immunitystandards

• Standardmodificationflexibility

(consult factory)

Low noise fan

Fan fail signal

Module enable

Outputs down to 0.5V

• FieldDemonstratedMTBF:>550,000

hours at full load, 220 Vac & 25 °C

ambient conditions

Total Power: 400 - 1200 Watts

Input Voltage: 85 - 264 VAC

120 - 350 VDC

# of Outputs: Up to 21

Safety

• UL UL1950

• CSA CSA22.2 No. 234 Level 5

• IEC IEC950, Class 1

• VDE EN60950,

• BABT Compliance to EN 60950,

BS 7002

• CB Certificate and report

• CE Mark

Rev. 07.19.11_89

MP Series

2 of 8

Embedded Power for

Business-Critical Continuity

313

process

yellow

3405

1797

1375

116

2607

652

242

2985

375

240

Module Type Single Single Single Dual Triple

Output 1 1 2 3

Max output power 210 W 360 W 600 W 144 W 36 W

Max output current 35 A 60 A 120 A 10 A 2 A

Volts 2-60 V 2-60 V 2-60 V 2-28 V 2-28V

Standard voltage increments 25 25 25 19 18

Remote sense on outputs Yes Yes Yes Yes, both No

Remote margin/V-Program Yes Yes Yes No No

Module Inhibit (isolated) Yes Yes Yes -- --

Single wire active current share Yes Yes Yes Yes, main only --

Over voltage / over current protection Yes Yes Yes Yes Over current

Minimum load required No No No Yes (10%) main only No

Slots occupied in any MP case 1 2 3 1 1

Output Module Line-up

Operating temperature: -20 °C to 50 °C (start @ 0 °C)

(derate each output linearly to 50% at 70 °C)

(-20 °C to 40 °C max. with rear air option)

Shock/Vibration: Mil-Hdbk 810E

Humidity: 95% non-condensing

Storage temperature: -40 °C to 85 °C

Temperature coefficient: 0.02% per °C

Cooling: Internal DC fan or customer provided air (option)

Environmental Specifications

Output

Adjustmentrange: ± 10% minimum all outputs

Margining: ± 4 - 6% nominal1

Overall regulation: 0.4% or 20mV max.

(36 W modules 4% maximum)

Ripple: RMS: 0.1% or 10mV, whichever is greater

Pk-Pk: 1.0% or 50mV, whichever is greater

Bandwidth limited to 20 MHz

Dynamic response: < 2% or 100 mV, with 25% load step

Recovery time: To within 1% in < 300 µsec

Overcurrent

protection:**

Single output module & main output of

dual output module

105-120% of rated output current.

Aux output of dual output module 105-

140% of rated output current

Short-circuit protection: Protected for continuous short-circuit

Recovery auto upon removal of short

Overvoltage protection:

(measured at sense

connection)

Single output module: 2-5.5 V 122-134% ; 6-60 V 100-120%

Dual output module: 2-6 V 122-134% ; 8-28 V 110-120%

Triple output module: No overvoltage protection provided.

Recycle AC input voltage to reset OVP

circuit

Reverse voltage protection: 100% of rated output current

Output (cont.)

Thermal protection: All outputs disabled when internal temp

exceeds safe operating range. > 5ms

warning (AC OK signal) before shutdown

Remote sense: Up to 0.5 V total drop (not avbl on triple

output module)

Single wire parallel: Current share to within 2% of total rated

current2

DC OK: -2% to -8% of nominal for any monitored

output2

Minimum load: Not required on single or triple output. 10%

required on main of dual output3

Housekeeping bias

voltage:

5 Vdc @ 1.0 A max. present whenever AC

input is applied

Module inhibit: TTL, isolated, singles and dual (both

outputs) only

Switching frequency: 250k Hz

Output/Output isolation: >1 Megohm

VME signal option board: POR signal & quad external DC OK

Hold-up module (HUP): 1-slot module providing additional 34mSec

(60mSec total); hold-up @ 600 W loading.

1. Single output modules only.

2. Single and main of dual output modules only

3. Contact factory for optional preload if required

Field Demonstrated MTBF: > 550,000 hours at full load, 220 Vac and

25 °C ambient conditions

Rev. 07.19.11_89

MP Series

3 of 8

Embedded Power for

Business-Critical Continuity

313

process

yellow

3405

1797

1375

116

2607

652

242

2985

375

240

Voltage Voltage

Code Single Output Module Code Dual Output** Triple Output

1 2 3 V1 V2 V1 V2 V3

2 V A35 A 60 A 120 A —10 A — — 2 A

2.2 V B35 A 60 A 120 A —10 A — — 2 A

3 V C35 A 60 A 120 A —10 A — — 2 A

3.3 V D35 A 60 A 120 A —10 A — — 2 A

5 V E35 A 60 A 120 A 10 A 10 A — — 2 A

5.2 V F35 A 60 A 115 A —10 A — — 2 A

5.5 V G34 A 58 A 109 A —10 A — — 2 A

6.0 V H23 A 42 A 78 A —10 A — — 2 A

8.0 V I20 A 36 A 68 A — — 1 A 1 A 1 A

10 V J18 A 32 A 60 A — — 1 A 1 A 1 A

11 V K17 A 31 A 54.5 A ——1 A 1 A 1 A

12 V L17 A 30 A 50 A 10 A 4 A 1 A 1 A 1 A

14 V M14 A 21 A 40.5 A 9 A 4 A 1 A 1 A 1 A

15 V N14 A 20 A 39 A 8 A 4 A 1 A 1 A 1 A

18 V O11 A 19 A 33.3 A — — — 0.5 A 0.5 A

20 V P10.5 A 18 A 30 A — — — 0.5 A 0.5 A

24 V Q8.5 A 15 A 23.5 A 4 A 2 A —0.5 A 0.5 A

28 V R6.7 A 12.8 A 21.4 A 3 A 2 A —0.5 A 0.5 A

30 V S6.5 A 12 A 20 A —————

33 V T6.2 A 10.9 A 18.2 A —————

36 V U5.8 A 10 A 16.6 A —————

42 V V4.2 A 7.5 A 12.5 A —————

48 V W4.0 A 7.5 A 12.5 A —————

54 V X3.7 A 6.0 A 11 A —————

60 V Y3.5 A 6.0 A 10 A —————

Non-std* Z Special Voltage - Consult Factory for specifications

2.4 V -2.7 V 35 A 60 A 120 A —10 A — — 2 A

3.6 V - 4.5 V 35 A 60 A 120 A —10 A — — 2 A

6.6 V -9.2 V 20 A 36 A 68 A 10 A 4 A — — 1 A

8.8 V - 9.0 V 18 A 32 A 60 A 10 A 4 A — — 1 A

Output Module Voltage/Current

MP1 -3L - 2E - 1Q - 4LL - HUP - 00 -###

Case Size (mm)

4 = 2.5” x 5” x 10”; 400 W-600 W, 5 Slots

(63.5 x 127 x 254)

6 = 2.5” x 5” x 11”; 600 W-800 W, 5 Slots

(63.5 x 127 x 279.4)

8 = 2.5” x 7” x 10”; 800 W-1000 W, 6 Slots

(63.5 x 177.8 x 254)

1 = 2.5” x 8” x 11”; 1000 W-1200 W, 7 Slots*

(63.5 x 203.2 x 279.4)

Module Codes

Module/Voltage/Option Codes

Module codes:

(None) = 36 W triple O/P (1 slot)

1 = 210 W single O/P (1 slot)

2 = 360 W single O/P (2 slot)

3 = 600 W single O/P (3 slot)

4 = 144 W dual O/P (1 slot)

5 - 9 = future

Case Option Codes

First digit

0 - 9 = parallel code

(See Parallel Codes table above)

Second digit

Standard Options

0 = No options

1 = Rear Air Exhaust

3 = Global enable

5 = Opt 1 + Opt 3

M = Low Leakage

N = Low Leakage + Opt 1

P = Low Leakage + Opt 3

R = Low Leakage + Opt 5

Add-on Modules

Voltage Codes:

See Output Module Voltage/

Current table above

Module/Voltage/Option Codes

First - Module Code

Second - Voltage Code

Case Option Codes

HUP = Hold up module

VME = VME POR signal

and isolated DC

Case Size

Factory assigned

for modifications

Hardware Code

Ordering Information

7 6 5 4 3 2 1

MP4 & MP6

available slots

MP8

available slots

Slot 1

Slot 2

Slot 3

Slot 4

Slot 5

Slot 1

Slot 2

Slot 3

Slot 4

Slot 5

Slot 6

Slot 1

Slot 2

Slot 3

Slot 4

Slot 6

Slot 7

Slot 5

MP1

available slots

Parallel Codes

0 = no parallel

1 = 1 & 2

2 = 2 & 3

3 = 3 & 4

4 = 4 & 5

5 = 3 & 4 & 5

6 = 5 & 6

7 = 4 & 5 & 6

8 = 6 & 7

9 = 3 & 4, 6 & 7

A = 1 & 2, 3 & 4, 5 & 6

C = 2 & 3, 4 & 5

E = 3 & 4, 5 & 6

F = 2 & 3, 4 & 5, 6 & 7

Notes:

1. Omit digits that do not apply.

2. Specify modules from lowest number of outputs to highest.

(Single/Dual/Triple)

3. If number of outputs are equal, specify modules from highest to

lowest power increments. If power increments are equal, specify

in descending alphabetical order (1A, B, C . . .).

4. Always start with Slot 1.

5. All MP model configurations created using this selection guide are

standard MP products with standard availability and lead times.

6. Optional VME/DCOK module must always be located in the last slot.

Module designator is “VME”.

RRev. 07.19.11_89

MP Series

4 of 8

Embedded Power for

Business-Critical Continuity

313

process

yellow

3405

1797

1375

116

2607

652

242

2985

375

240

Input

85-264 Vac 180-264 Vac

MP8 = 2.5” x 7” x 10” 6 available slots 800 W max. 1000 W max.

(63.5 x 177.8 x 254mm)

OUTPUT MODULE AREA

AC INPUT S

177.8

7.0

-A-

(4 PL)

NON-CUMULATIVE

4.3 .8

.17 .03 23.9 .5

.94 .02

S

L

O

S

L

O

S

L

O

S

L

O

S

L

O

54321

MP4 & MP6

MP8

Single

PFC Input Connector

J1 Control Connector Standard for all cases

Pin No. Function

J1-1 Input AC OK - “emitter”

J1-2 Input AC OK - “collector”

J1-3 Global DC OK - “emitter”

J1-4 Global DC OK - “collector”

J1-5 Spare

J1-6 Global inhibit/optional enable logic “0”

J1-7 Global inhibit/optional enable logic “1”

J1-8 Global inhibit/optional enable return

J1-9 SELV 5 V housekeeping

J1-10 SE:V 5 V housekeeping return

Mates with

Molex 90142-0010 Housing

90119-2110 Pin

Figure 1. Connector J1

Input

85-264 Vac 180-264 Vac

MP4 = 2.5” x 5” x 10” 5 available slots 400 W max. 600 W max.

(63.5 x 127 x 254mm)

MP6 = 2.5” x 8” x 11” 5 available slots 600 W max. 800 W max.

(63.5 x 127 x 279.4mm)

210 W

360 W

600 W

144 W

Pin Connectors

Triple

Dual

36 W

Input

85-264 Vac 180-264 Vac

MP1 = 2.5” x 8” x 11” 7 available slots 1000 W max. 1200 W max.

(63.5 x 203.2 x 279.4mm)

MP1

Rev. 07.19.11_89

MP Series

5 of 8

Embedded Power for

Business-Critical Continuity

313

process

yellow

3405

1797

1375

116

2607

652

242

2985

375

240

DC-DC Converter Output Modules

PIN 1

V+

M4X8 SCREWS (4X)

V-

V ADJ

.32 (8.1)

.44 (11.3)

(2X) (2X)

.33 (8.5)

.63 (16.0)

.48 (12.1)

1.38 (35.1)

PIN 1

V2 ADJ

.32

(8.1)

.42 (10.7)

V1 +

V1 -

V2 -

V2 +

M3X8 SCREWS (4X)

.46 (11.7)

(4X)

.30 (7.5)(3X)

V1 ADJ

1.17 (29.7)

Single 210 Watt

Dual 144 Watt

Single 360 Watt

Single 600 Watt

MP Modules

Mechanical Drawings

Triple 36 Watt

V2 ADJ

V1 ADJ

PIN 1

V3 ADJ

DC OUTPUT CONNECTION

.48

(12.1)

.84

(21.3)

M4X8 SCREWS (4X)

V-

PIN 1

V ADJ

V+

.44

(11.3)

.32 

(8.1)

1.24 (31.6) (2X)

.61 (15.6)

(2X)

.63 

(16.0)

.59 

(15.0)

V1+

V1-

V2+

V2-

V3+

V3-

Figure 1. AC Input

Figure 2. Connector J1

Mates with

Molex 90142-0010 Housing

90119-2110 Pin

Figure 4. Connector J1

PFC Input Connector

Pin No. Function

1+ Remote Sense single or dual o/p main

2Remote Margin / V. Program single o/p

3Margin High single o/p

4- Remote Sense/Margin Low single or dual o/p main

5 Spare

6Module, Isolated Inhibit single or dual o/p

7Module Inhibit Return single or dual o/p

8Current Share (SWP) single or dual o/p main

9+ Remote Sense V2 dual o/p, single is spare

10 - Remote Sense V2 dual o/p, single is spare PIN 1

.32 

(8.1)

.44 (11.2 )

(2X)

V+

M4X8 SCREWS (2X)

V-

V ADJ

.48 (12.1)

.44 (11.3)

1.38 

(35.1)

Rev. 07.19.11_89

MP Series

6 of 8

Embedded Power for

Business-Critical Continuity

313

process

yellow

3405

1797

1375

116

2607

652

242

2985

375

240

Notes

1. Input: Barrier type. Three No. 6-32 B.H. screws (0.375” centers). Max torque: 6 in-lbs. (0.67 N-m).

2. Control connectors: (J1 and J2) 10 position housing, gold plated contacts. Mates with Molex 90142-0010 housing with 90119-2110 crimp contacts (Molex C - Grid III

Series). Connector kit includes mating connector and 10 pins, Astec part #70-841-004.

3. Chassis material: aluminum with chemical film coating (conductive).

4. All dimensions are in millimeters and inches, and are typical.

5. Customer mounting -3 sides M4, bottom also includes 8-32 mounting holes. Max. penetration is 0.150” (3.8 mm). Max. torque: 5 in-lbs.

6. Output module connections: All single O/P modules are M4 x 8mm screws. Max. torque: 10 in-lbs.

Dual O/P module is M3 x 8mm screws. Max. torque: 5 in-lbs.

Triple O/P module is .045” square pins on .156” centers. Mates with Moelx 09-50-8063 or equivalent.

MP Series

MP4 (400/600 Watts Max)

MP6 (600/800 Watts Max)

5-Inch Case Size: MP4: 2.5” x 5” x 10” (63.5mm x 127mm x 254mm)

5-Inch Case Size: MP6: 2.5” x 5” x 11” (63.5mm x 127mm x 279.4mm)

Weight:MP4Case:2.6lbs.•MP6Case:3.2lbs.•36WTriple:0.5lb.

•210WSingle:0.6lb.•360WSingle:1.0lb.•600WSingle:2.0lbs

•144WDual:0.6lb

19.05

.750

171.45

6.750

29.05

1.144

171.45

6.750

M4 MTG HOLES

4 PL

MARKED "B"

#8-32 MTG HOLES

4 PL

MARKED "A"

101.60

4.000

12.70

.500

Standard Airflow

+.0

-.5

127.0

+.00

-.02

5.00

19.0

.75

49.2

1.94

+.0

-.5

254.0

+.00

-.02

10.00 3.7

.15TYP

19.05

.750

+.0

-.5

63.5

+.00

-.02

2.50

3.5

.14 (TYP)

M4 MTG HOLES 4 PL

MOUNTING HOLES DIMENSIONS IDENTICAL ON BOTH SIDES

17.3 1.0

.68 .04

171.45

6.750

38.10

1.500

12.70

.500

MP4 +.0

-.5

279.4

+.00

-.02

11.00

MP6

Rev. 07.19.11_89

MP Series

7 of 8

Embedded Power for

Business-Critical Continuity

313

process

yellow

3405

1797

1375

116

2607

652

242

2985

375

240

MP Series

MP8 (800/1000 Watts Max)

7-Inch Case Size: MP8: 2.5” x 7” x 10” (63.5mm x 177.8mm x 254mm)

Weight:MP8Case:4.1lbs.•36WTriple:0.5lb.•210WSingle:0.6lb.

•360WSingle:1.0lb.•600WSingle:2.6lbs.•144WDual:0.6lb.

Notes

1. Input: Barrier type. Three No. 6-32 B.H. screws (0.375” centers). Max torque: 6 in-lbs. (0.67 N-m).

2. Control connectors: (J1 and J2) 10 position housing, gold plated contacts. Mates with Molex 90142-0010 housing with 90119-2110 crimp contacts (Molex C - Grid III

Series). Connector kit includes mating connector and 10 pins, Astec part #70-841-004.

3. Chassis material: aluminum with chemical film coating (conductive).

4. All dimensions are in millimeters and inches, and are typical.

5. Customer mounting -3 sides M4, bottom also includes 8-32 mounting holes. Max. penetration is 0.150” (3.8 mm). Max. torque: 5 in-lbs.

6. Output module connections: All single O/P modules are M4 x 8mm screws. Max. torque: 10 in-lbs.

Dual O/P module is M3 x 8mm screws. Max. torque: 5 in-lbs.

Triple O/P Module is .045” square pins on .156 centers. Mates with Moelx 09-50-8063 or equivalent.

19.05

0.75

171.45

6.75

29.05

1.1

171.45

6.75

12.70

0.5

M4 MOUNTING HOLES

#8-32 MOUNTING HOLES

MARKED "A" (4X)

"A"

"A" "A"

"A"

"B"

MARKED "B" (4X)

"B"

152.40

6.0

254

10.0

Standard Airflow

59.5

2.34

60.5

2.38

14.0

0.55

14.7

0.58

31.8

1.25

177.8

7.0

63.5

2.5

M4 MOUNTING HOLES (4X)

171.45

6.75

19.05

0.7

38.10

1.5 35.0

1.38

12.70

0.5 254

10.0

63.5

2.5

Rev. 07.19.11_89

MP Series

8 of 8

Embedded Power for

Business-Critical Continuity

313

process

yellow

3405

1797

1375

116

2607

652

242

2985

375

240

Americas

5810 Van Allen Way

Carlsbad, CA 92008

USA

Telephone: +1 760 930 4600

Facsimile: +1 760 930 0698

Europe (UK)

Waterfront Business Park

Merry Hill, Dudley

West Midlands, DY5 1LX

United Kingdom

Telephone: +44 (0) 1384 842 211

Facsimile: +44 (0) 1384 843 355

Asia (HK)

14/F, Lu Plaza

2 Wing Yip Street

Kwun Tong, Kowloon

Hong Kong

Telephone: +852 2176 3333

Facsimile: +852 2176 3888

For global contact, visit:

www.Emerson.com/EmbeddedPower

techsupport.embeddedpower

@emerson.com

While every precaution has been taken to ensure

accuracy and completeness in this literature, Emerson

Network Power assumes no responsibility, and disclaims

all liability for damages resulting from use of this

information or for any errors or omissions.

Emerson Network Power and the Emerson

Network Power logo are trademarks and

service marks of Emerson Electric Co.

EmersonNetworkPower.com

Embedded Computing

Embedded Power

Monitoring

Outside Plant

Power Switching & Controls

Precision Cooling

Racks & Integrated Cabinets

Services

Surge Protection

Emerson Network Power.

The global leader in enabling

business-critical continuity.

AC Power

Connectivity

DC Power

8-Inch Case Size: MP1: 2.5” x 8” x 11” (63.5mm x 203.2mm x 279.4mm)

Weight:MP1Case:5.0lbs.•36WTriple:0.5lb.

•210WSingle:0.6lb.•360WSingle:1.0lb.

•600WSingle:2.0lbs.•144WDual:0.6lb.

Notes

1. Input: Barrier type. Three No. 6-32 B.H. screws (0.375” centers). Max torque: 6 in-lbs (0.67 N-m).

2. Control connectors: (J1 and J2) 10 position housing, gold plated contacts. Mates with Molex 90142-0010 housing with

90119-2110 crimp contacts (Molex C - Grid III Series). Connector kit includes mating connector and 10 pins, Astec part #70-

841-004.

3. Chassis material: aluminum with chemical film coating (conductive).

4. All dimensions are in millimeters and inches, and are typical.

5. Customer mounting -3 sides M4, bottom also includes 8-32 mounting holes. Max. penetration is 0.150” (3.8 mm). Max.

torque: 5 in-lbs.

6. Output module connections: All single O/P modules are M4 x 8mm screws. Max. torque: 10 in-lbs.

Dual O/P module is M3 x 8mm screws. Max. torque: 5 in-lbs.

Triple O/P module is .045” square pins on .156 centers. Mates with Molex 09-50-8063 or equivalent.

MP Series

MP1 (1000/1200 Watts Max)

171.45

6.750

171.45

6.750

19.05

.750

177.80

7.000

29.05

1.144 12.70

.500

BOTTOM MOUNTING SURFACE

M4 MTG HOLES

4 PL

MARKED “B”

STD AIR FLOW

#8-32 MTG HOLES

4 PL

MARKED “A”

203.2

8.00

31.8

1.25

76.2

3.00

69.9

2.75

14.0

.55

14.7

.58

171.45

6.750

38.10

1.500

12.70

.500 279.4

11.00

35.0

1.38

19.05

.750

16.50

6.50

63.5

2.50

M4 MTG HOLES 4 PL

MOUNTING HOLES - DIMENSIONS

IDENTICAL ON BOTH SIDES