OPA656 OPA 656 www.ti.com SBOS196G - DECEMBER 2001 - REVISED NOVEMBER 2008 Wideband, Unity-Gain Stable, FET-Input OPERATIONAL AMPLIFIER FEATURES DESCRIPTION The OPA656 combines a very wideband, unity-gain stable, voltage-feedback op amp with a FET-input stage to offer an ultra high dynamic-range amplifier for ADC (Analog-to-Digital Converter) buffering and transimpedance applications. Extremely low DC errors give good precision in optical applications. 500MHz UNITY-GAIN BANDWIDTH LOW INPUT BIAS CURRENT: 2pA LOW OFFSET AND DRIFT: 0.25mV, 2V/C LOW DISTORTION: 74dB SFDR at 5MHz HIGH OUTPUT CURRENT: 70mA LOW INPUT VOLTAGE NOISE: 7nV/Hz APPLICATIONS WIDEBAND PHOTODIODE AMPLIFIERS SAMPLE-AND-HOLD BUFFERS CCD OUTPUT BUFFERS ADC INPUT BUFFERS WIDEBAND PRECISION AMPLIFIERS TEST AND MEASUREMENT FRONT ENDS The high unity-gain stable bandwidth and JFET input allows exceptional performance in high-speed, low-noise integrators. The high input impedance and low bias current provided by the FET input is supported by the ultra-low 7nV/Hz input voltage noise to achieve a very low integrated noise in wideband photodiode transimpedance applications. Broad transimpedance bandwidths are achievable given the OPA656's high 230MHz gain bandwidth product. As shown below, a -3dB bandwidth of 1MHz is provided even for a high 1M transimpedance gain from a 47pF source capacitance. RELATED OPERATIONAL AMPLIFIER PRODUCTS SLEW VOLTAGE VS BW RATE NOISE (V) (MHz) (V/S) (nV/HZ) AMPLIFIER DESCRIPTION DEVICE 1pF 499k OPA355 +5 200 OPA655 5 400 OPA657 5 1600 OPA627 15 16 THS4601 15 180 499k 300 290 700 55 100 5.8 6 4.8 4.5 5.4 Unity-Gain Stable CMOS Unity-Gain Stable FET-Input Gain of +7 Stable FET-Input Unity-Gain Stable FET-Input Unity-Gain Stable FET-Input 1M TRANSIMPEDANCE BANDWIDTH OPA656 Transimpedance Gain (dB) 130 VO (47pF) -Vb 1MHz Bandwidth 120 110 100 90 Wideband Photodiode Transimpedance Amplifier 80 10kHz 100kHz 1MHz 5MHz Frequency Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. Copyright (c) 2001-2008, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. www.ti.com ELECTROSTATIC DISCHARGE SENSITIVITY ABSOLUTE MAXIMUM RATINGS(1) Supply Voltage ................................................................................. 6.5V Internal Power Dissipation ........................... See Thermal Characteristics Differential Input Voltage ..................................................................... VS Input Voltage Range ............................................................................ VS Storage Temperature Range ......................................... -65C to +125C Lead Temperature ......................................................................... +260C Junction Temperature (TJ ) ........................................................... +150C ESD Rating (Human Body Model) .................................................. 2000V (Machine Model) ............................................................ 200V This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. NOTE: (1) Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may degrade device reliability. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those specified is not implied. PACKAGE/ORDERING INFORMATION(1) SPECIFIED TEMPERATURE RANGE PACKAGE MARKING PRODUCT PACKAGE-LEAD PACKAGE DESIGNATOR OPA656U SO-8 Surface Mount D -40C to +85C OPA656U OPA656U Rails, 100 " " " " OPA656U/2K5 Tape and Reel, 2500 SO-8 Surface Mount D -40C to +85C OPA656UB OPA656UB Rails, 100 " " " " OPA656UB/2K5 Tape and Reel, 2500 SOT23-5 DBV -40C to +85C B56 OPA656N/250 Tape and Reel, 250 " " " " OPA656N/3K Tape and Reel, 3000 SOT23-5 DBV -40C to +85C B56 OPA656NB/250 Tape and Reel, 250 " " " " OPA656NB/3K Tape and Reel, 3000 " OPA656UB " OPA656N " OPA656NB " ORDERING NUMBER(2) TRANSPORT MEDIA, QUANTITY NOTE: (1) For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI website at www.ti.com. (2) UB and NB are high grade, while U and N are standard grade. PIN CONFIGURATIONS NC 1 8 NC Inverting Input 2 7 +VS Noninverting Input 3 6 Output -VS 4 5 NC Top View SOT23 Output 1 -VS 2 Noninverting Input 3 5 +VS 4 Inverting Input 4 SO 5 Top View 3 2 1 B56 Pin Orientation/Package Marking 2 OPA656 www.ti.com SBOS196G ELECTRICAL CHARACTERISTICS: VS = 5V RF = 250, RL = 100, and G = +2, unless otherwise noted. Figure 1 for AC performance. OPA656U, N (Standard-Grade) TYP PARAMETER AC PERFORMANCE (Figure 1) Small-Signal Bandwidth Gain-Bandwidth Product Bandwidth for 0.1dB flatness Peaking at a Gain of +1 Large-Signal Bandwidth Slew Rate Rise-and-Fall Time Settling Time to 0.02% Harmonic Distortion 2nd-Harmonic 3rd-Harmonic Input Voltage Noise Input Current Noise Differential Gain Differential Phase DC PERFORMANCE(4) Open-Loop Voltage Gain (AOL) Input Offset Voltage Average Offset Voltage Drift Input Bias Current Input Offset Current INPUT Most Positive Input Voltage(5) Most Negative Input Voltage(5) Most Positive Input Voltage(6) Most Negative Input Voltage(6) Common-Mode Rejection Ratio (CMRR) Input Impedance Differential Common-Mode OUTPUT Voltage Output Swing Current Output, Sourcing Current Output, Sinking Closed-Loop Output Impedance POWER SUPPLY Specified Operating Voltage Maximum Operating Voltage Range Maximum Quiescent Current Minimum Quiescent Current Power-Supply Rejection Ratio (+PSRR) (-PSRR) TEMPERATURE RANGE Specified Operating Range: U, N Package Thermal Resistance, JA U: SO-8 N: SOT23-5 MIN/MAX OVER TEMPERATURE +25C(1) 0C to 70C(2) -40C to +85C(2) MIN/ TEST MAX LEVEL(3) CONDITIONS +25C G = +1, VO = 200mVPP, RF = 0 G = +2, VO = 200mVPP G = +5, VO = 200mVPP G = +10, VO = 200mVPP G > +10 G = +2, VO = 200mVPP VO < 200mVPP, RF = 0 G = +2, VO = 2VPP G = +2, 1V Step 0.2V Step G = +2, VO = 2V Step G = +2, f = 5MHz, VO = 2VPP RL = 200 RL > 500 RL = 200 RL > 500 f > 100kHz f > 100kHz G = +2, PAL, RL = 150 G = +2, PAL, RL = 150 500 200 59 23 230 30 1.5 75 290 1.5 21 MHz MHz MHz MHz MHz MHz dB MHz V/s ns ns Typ Typ Typ Typ Typ Typ Typ Typ Typ Typ Typ C C C C C C C C C C C -71 -74 -81 -100 7 1.3 0.02 0.05 dBc dBc dBc dBc nV/Hz fA/Hz % Typ Typ Typ Typ Typ Typ Typ Typ C C C C C C C C VO = 0V, RL = 100 VCM = 0V VCM = 0V VCM = 0V VCM = 0V 65 0.25 2 2 1 1.8 12 20 10 60 59 2.2 12 1800 900 58 2.6 12 5000 2500 dB mV V/C pA pA Min Max Max Max Max A A A A B VCM = 0.5V +2.75 -4.5 +3.25 -4.5 86 +2.1 -4.0 +2.6 -4.0 80 +2.05 -3.9 +2.5 -3.9 78 +2.0 -3.8 +2.4 -3.8 76 V V V V dB Min Min Min Min Min A A A A A || pF || pF Typ Typ C C 1012 || 0.7 1012 || 2.8 No Load RL = 100 G = +1, f = 0.1MHz 3.9 3.5 +70 -70 0.01 3.2 48 -48 3.1 46 -46 V V mA mA Typ Min Min Min Typ A A A C 6 16.2 11.4 70 54 6 16.3 11.1 68 52 V V mA mA dB dB Typ Max Max Min Min Min C A A A A A -40 to 85 C Typ 125 150 C/W C/W Typ Typ 5 +VS = 4.50V to 5.50V -VS = 4.50V to -5.50V 3.7 3.3 UNITS 14 14 76 62 50 -50 6 16 11.7 72 56 Junction-to-Ambient NOTES: (1) Junction temperature = ambient for 25C min/max specifications. (2) Junction temperature = ambient at low temperature limit: junction temperature = ambient +20C at high temperature limit for over temperature min/max specifications. (3) Test Levels: (A) 100% tested at 25C. Over temperature limits by characterization and simulation. (B) Limits set by characterization and simulation. (C) Typical value only for information. (4) Current is considered positive out-of-node. VCM is the input common-mode voltage. (5) Tested < 3dB below minimum specified CMRR at CMIR limits. (6) Input range to give > 53dB CMRR. OPA656 SBOS196G www.ti.com 3 ELECTRICAL CHARACTERISTICS: VS = 5V: High Grade DC Specifications(1) RF = 250, RL = 100, and G = +2, unless otherwise noted. OPA656UB, NB (High-Grade) TYP PARAMETER Input Offset Voltage Input Offset Voltage Drift Input Bias Current Input Offset Current Common-Mode Rejection Ratio (CMRR) Power-Supply Rejection Ratio (+PSRR) (-PSRR) MIN/MAX OVER TEMPERATURE CONDITIONS +25C +25C(2) VCM = 0V VCM = 0V VCM = 0V VCM = 0V VCM = 0.5V +VS = 4.5V to 5.5V -VS = -4.5V to -5.5V 0.1 2 1 0.5 95 78 68 0.6 6 5 5 88 74 62 0C to 70C(3) -40C to +85C(3) UNITS MIN/ TEST MAX LEVEL(4) 0.85 6 450 450 86 72 60 0.9 6 1250 1250 84 70 58 mV V/C pA pA dB dB dB Max Max Max Max Min Min Min A A A A A A A NOTES: (1) All other specifications are the same as the standard-grade. (2) Junction temperature = ambient for 25C min/max specifications. (3) Junction temperature = ambient at low temperature limit: junction temperature = ambient +20C at high temperature limit for over temperature min/max specifications. (4) Test Levels: (A) 100% tested at 25C. Over temperature limits by characterization and simulation. 4 OPA656 www.ti.com SBOS196G TYPICAL CHARACTERISTICS: VS = 5V TA = +25C, G = +2, RF = 250, RL = 100, unless otherwise noted. NONINVERTING SMALL-SIGNAL FREQUENCY RESPONSE INVERTING SMALL-SIGNAL FREQUENCY RESPONSE 6 9 3 0 G = +2 -3 -6 G = +5 -9 -12 G = +10 See Figure 1 VO = 200mVp-p RF = 402 6 Normalized Gain (dB) 3 0 -6 G = -5 -9 -12 G = -10 -15 See Figure 2 -21 -18 -24 0.5 1 10 Frequency (MHz) 100 500 0.5 1 10 Frequency (MHz) NONINVERTING LARGE-SIGNAL FREQUENCY RESPONSE 9 500 3 VO = 0.5Vp-p G = -1 0 6 -3 Gain (dB) VO = 0.5Vp-p 3 Gain (dB) 100 INVERTING LARGE-SIGNAL FREQUENCY RESPONSE VO = 0.2Vp-p G = +2 VO = 1Vp-p 0 VO = 2Vp-p -3 VO = 1Vp-p -6 VO = 2Vp-p -9 -12 See Figure 1 See Figure 2 -6 -15 -18 -9 0.5 1 10 Frequency (MHz) 100 500 0.5 1 G = +2 0.6 0.4 1.2 Large-Signal Right Scale 0.2 0 0.8 0.4 Small-Signal Left Scale 0 -0.2 -0.4 -0.4 -0.8 See Figure 1 -0.6 -1.2 -0.8 -1.6 Time (10ns/div) 100 500 0.8 1.6 G = -1 0.6 0.4 1.2 Large-Signal Right Scale 0.2 0 0.8 0.4 Small-Signal Left Scale -0.2 0 -0.4 -0.4 -0.8 See Figure 2 -0.6 -1.2 -0.8 -1.6 Time (10ns/div) OPA656 SBOS196G 10 Frequency (MHz) INVERTING PULSE RESPONSE 1.6 Small-Signal Output Voltage (200mV/div) 0.8 Large-Signal Output Voltage (400mV/div) NONINVERTING PULSE RESPONSE Small-Signal Output Voltage (200mV/div) G = -2 -3 -18 -15 G = -1 www.ti.com 5 Large-Signal Output Voltage (400mV/div) Normalized Gain (dB) G = +1 RF = 0 VO = 200mVp-p TYPICAL CHARACTERISTICS: VS = 5V (Cont.) TA = +25C, G = +2, RF = 250, RL = 100, unless otherwise noted. HARMONIC DISTORTION vs OUTPUT VOLTAGE (5MHz) HARMONIC DISTORTION vs LOAD RESISTANCE -60 -60 VO = 2Vp-p f = 5MHz -70 -75 2nd Harmonic -80 -85 -90 3rd Harmonic -95 -100 See Figure 1 -105 f = 5MHz RL = 200 -65 Harmonic Distortion (dBc) Harmonic Distortion (dBc) -65 -70 -75 -80 -85 3rd Harmonic -90 -95 -100 -110 -105 100 1k 0.5 1 Output Voltage Swing (Vp-p) Resistance () f = 1MHz RL = 200 -75 Harmonic Distortion (dBc) Harmonic Distortion (dBc) -70 VO = 2Vp-p RL = 200 -60 2nd Harmonic -70 -80 -90 3rd Harmonic -100 2nd Harmonic -80 -85 -90 -95 3rd Harmonic -100 See Figure 1 -105 See Figure 1 -110 -110 0.1 1 Frequency (MHz) 10 20 0.5 HARMONIC DISTORTION vs NONINVERTING GAIN 1 Output Voltage Swing (Vp-p) 5 HARMONIC DISTORTION vs INVERTING GAIN -60 -60 VO = 2Vp-p f = 5MHz RL = 200 -70 2nd Harmonic Harmonic Distortion (dBc) Harmonic Distortion (dBc) 5 HARMONIC DISTORTION vs OUTPUT VOLTAGE (1MHz) HARMONIC DISTORTION vs FREQUENCY -50 -80 3rd Harmonic -90 -100 VO = 2Vp-p RF = 604 F = 5MHz RL = 200 -65 2nd Harmonic -70 -75 3rd Harmonic -80 -85 See Figure 2, RG and RM Adjusted See Figure 1, RG Adjusted -110 -90 1 10 -1 Gain (V/V) 6 2nd Harmonic -10 Gain (V/V) OPA656 www.ti.com SBOS196G TYPICAL CHARACTERISTICS: VS = 5V (Cont.) TA = +25C, G = +2, RF = 250, RL = 100, unless otherwise noted. 2-TONE, 3RD-ORDER INTERMODULATION SPURIOUS INPUT CURRENT AND VOLTAGE NOISE DENSITY -30 3rd-Order Spurious Level (dBc) 10 Input Voltage Noise 7nV/Hz Input Current Noise 1.3fA/Hz 1 PI -40 50 50 -50 -60 250 10MHz -70 5MHz -80 -90 2MHz 100 1k 10k f (Hz) 100k 1M 10M -10 -8 COMMON-MODE REJECTION RATIO AND POWER-SUPPLY REJECTION RATIO vs FREQUENCY 6 8 0 70 CMRR 100 20 log(AOL) 60 Open-Loop Gain (dB) 90 +PSRR 80 PSRR (dB) -6 -4 -2 0 2 4 Single-Tone Load Power (dBm) OPEN-LOOP GAIN AND PHASE 110 70 -PSRR 60 50 40 30 -30 -60 50 -90 40 < AOL 30 -120 20 -150 10 -180 -210 0 20 1k 10k 100k 1M 10M 100M 100 1k 10k Frequency (Hz) RECOMMENDED RS vs CAPACITIVE LOAD Normalized Gain to Capacitive Load (dB) For Maximally Flat Frequency Response 1 100 1k 10M 100M 1G 9 CL = 10pF 6 CL = 22pF 3 CL = 100pF 0 VI -3 RS VO 50 OPA656 CL -6 1k 250 -9 250 -12 1 Capacitive Load (pF) 10 100 500 Frequency (MHz) OPA656 SBOS196G 1M FREQUENCY RESPONSE vs CAPACITIVE LOAD 10 10 100k Frequency (Hz) 100 RS () 15MHz 250 -100 10 CMRR (dB) PO 50 OPA656 www.ti.com 7 Open-Loop Phase (30/div) in (fA/Hz) en (nV/Hz) 100 TYPICAL CHARACTERISTICS: VS = 5V (Cont.) TA = +25C, G = +2, RF = 250, RL = 100, unless otherwise noted. TYPICAL INPUT OFFSET VOLTAGE DRIFT OVER TEMPERATURE TYPICAL INPUT BIAS CURRENT vs COMMON-MODE INPUT VOLTAGE 1.0 2.0 Input Bias Current (pA) Input Offset Voltage (mV) 1.5 0.5 0 -0.5 1.0 0.5 0 -0.5 -1.0 -1.5 -1.0 -2.0 -25 0 25 50 75 100 125 -3 -2 Ambient Temperature (C) -1 TYPICAL INPUT BIAS CURRENT DRIFT OVER TEMPERATURE 1 2 3 SUPPLY AND OUTPUT CURRENT vs TEMPERATURE 1000 150 18 Supply Current Output Current (25mA/div) 900 Input Bias Current (pA) 0 Common-Mode Input Voltage (V) 800 700 600 500 400 300 200 Right Scale 125 15 Left Scale 100 Sourcing Current 12 75 9 50 6 Left Scale Sinking Current 25 3 100 0 0 -50 -25 0 25 50 75 100 125 0 -50 -25 0 Ambient Temperature (C) 3.2 4 2.4 3.2 1.6 1.6 0 0 -1.6 -3.2 -0.8 RL = 100 G = +2 -1.6 -4.8 -6.4 0.8 -2.4 See Figure 1 -8.0 3 2 100 125 Input RL = 100 RF = 402 G = -1 1 0 -1 -2 Output -3 -3.2 -4 -4.0 -5 Time (20ns/div) 8 Input and Output Voltage (V) Output Voltage (V) 5 4.8 Output Voltage Left Scale 75 INVERTING OVERDRIVE RECOVERY 4.0 Input Voltage (V) Input Voltage Right Scale 6.4 50 Ambient Temperature (C) NONINVERTING INPUT OVERDRIVE RECOVERY 8.0 25 See Figure 2 Time (20ns/div) OPA656 www.ti.com SBOS196G Supply Current (3mA/div) -50 TYPICAL CHARACTERISTICS: VS = 5V (Cont.) TA = +25C, G = +2, RF = 250, RL = 100, unless otherwise noted. CLOSED-LOOP OUTPUT IMPEDANCE vs FREQUENCY OUTPUT VOLTAGE AND CURRENT LIMITATIONS 10 5 4 1W Internal Power VO (V) 2 1 Output Impedance () 3 RL = 100 RL = 50 0 RL = 25 -1 -2 1 0.1 -3 -4 -5 -100 -80 1W Internal Power -60 -40 -20 0 20 40 60 80 0.01 1k 100 10k 100k 1M 10M 100M Frequency (Hz) IO (mA) COMMON-MODE REJECTION RATIO vs COMMON-MODE INPUT VOLTAGE CMRR (dB) 110 90 70 50 -5 -4 -3 -2 -1 0 1 2 3 4 5 Common-Mode Input Voltage (V) OPA656 SBOS196G www.ti.com 9 APPLICATIONS INFORMATION WIDEBAND, NONINVERTING OPERATION The OPA656 provides a unique combination of a broadband, unity gain stable, voltage-feedback amplifier with the DC precision of a trimmed JFET-input stage. Its very high Gain Bandwidth Product (GBP) of 230MHz can be used to either deliver high signal bandwidths for low-gain buffers, or to deliver broadband, low-noise transimpedance bandwidth to photodiode-detector applications. To achieve the full performance of the OPA656, careful attention to printed circuit board (PCB) layout and component selection is required as discussed in the remaining sections of this data sheet. Figure 1 shows the noninverting gain of +2 circuit used as the basis for most of the Typical Characteristics. Most of the curves were characterized using signal sources with 50 driving impedance, and with measurement equipment presenting a 50 load impedance. In Figure 1, the 50 shunt resistor at the VI terminal matches the source impedance of the test generator, while the 50 series resistor at the VO terminal provides a matching resistor for the measurement equipment load. Generally, data sheet voltage swing specifications are at the output pin (VO in Figure 1) while output power specifications are at the matched 50 load. The total 100 load at the output combined with the 500 total feedback network load, presents the OPA656 with an effective output load of 83 for the circuit of Figure 1. WIDEBAND, INVERTING GAIN OPERATION The circuit of Figure 2 shows the inverting gain of -1 test circuit used for most of the inverting Typical Characteristics. In this case, an additional resistor RM is used to achieve the 50 input impedance required by the test equipment using in characterization. This input impedance matching is optional in a circuit board environment where the OPA656 is used as an inverting amplifier at the output of a prior stage. +5V +VS 0.1F VO + 6.8F 50 50 Load OPA656 50 Source RG 402 RF 402 VI RM 57.6 0.1F + 6.8F -VS -5V FIGURE 2. Inverting G = -1 Specifications and Test Circuit. +5V In this configuration, the output sees the feedback resistor as an additional load in parallel with the 100 load used for test. It is often useful to increase the RF value to decrease the loading on the output (improving harmonic distortion) with the constraint that the parallel combination of RF || RG < 200. For higher inverting gains with the DC precision provided by the FET input OPA656, consider the higher gain bandwidth +VS 0.1F 6.8F + 50 Source 50 Load VI 50 VO OPA656 50 product OPA657. RF 250 RG 250 + 6.8F 0.1F -VS -5V FIGURE 1. Noninverting G = +2 Specifications and Test Circuit. Voltage-feedback op amps, unlike current feedback products, can use a wide range of resistor values to set their gain. To retain a controlled frequency response for the noninverting voltage amplifier of Figure 1, the parallel combination of RF || RG should always < 200. In the noninverting configuration, the parallel combination of RF || RG will form a pole with the parasitic input capacitance at the inverting node of the OPA656 (including layout parasitics). For best performance, this pole should be at a frequency greater than the closed loop bandwidth for the OPA656. For this reason, a direct short from output to inverting input is recommended for the unity gain follower application. 10 Figure 2 also shows the noninverting input tied directly to ground. Often, a bias current canceling resistor to ground is included here to null out the DC errors caused by input bias current effects. This is only useful when the input bias currents are matched. For a JFET part like the OPA656, the input bias currents do not match but are so low to begin with (< 5pA) that DC errors due to input bias currents are negligible. Hence, no resistor is recommended at the noninverting inputs for the inverting signal path condition. WIDEBAND, HIGH SENSITIVITY, TRANSIMPEDANCE DESIGN The high GBP and low input voltage and current noise for the OPA656 make it an ideal wideband transimpedance amplifier for low to moderate transimpedance gains. Higher transimpedance gains (> 100k) will benefit from the low input noise current of a FET input op amp such as the OPA656. One transimpedance design example is shown on the front page of the data sheet. Designs that require high bandwidth from a large area detector will benefit from the low input voltage noise for the OPA656. This input voltage noise OPA656 www.ti.com SBOS196G is peaked up over frequency by the diode source capacitance, and can, in many cases, become the limiting factor to input sensitivity. The key elements to the design are the expected diode capacitance (CD) with the reverse bias voltage (-VB) applied, the desired transimpedance gain, RF, and the GBP for the OPA656 (230MHz). Figure 3 shows a design from a 25pF source capacitance diode through a 50k transimpedance gain. With these 3 variables set (including the parasitic input capacitance for the OPA656 added to CD), the feedback capacitor value (CF) may be set to control the frequency response. If the total output noise is bandlimited to a frequency less than the feedback pole frequency (1/RFCF), a very simple expression for the equivalent input noise current can be derived as: iEQ = Equivalent input noise current if the output noise is bandlimited to F < 1/(2RFCD). iN = Input current noise for the op amp inverting input. eN = Input voltage noise for the op amp. Supply Decoupling Not Shown OPA656 CD = Diode capacitance. F = Bandlimiting frequency in Hz (usually a postfilter prior to further signal processing). VO = ID RF 4kT = 1.6E - 20J at 290K. RF 50k ID CD 25pF -5V 2 Where: +5V (E 2CDF) 4kT EN + N + RF RF 3 2 2 IEQ = IN + CF 0.6pF -VB FIGURE 3. Wideband, Low-Noise, Transimpedance Amplifier. To achieve a maximally flat 2nd-order Butterworth frequency response, the feedback pole should be set to: Evaluating this expression up to the feedback pole frequency at 3.8MHz for the circuit of Figure 3, gives an equivalent input noise current of 2.7pA/ Hz . This is much higher than the 1.3fA/ Hz for just the op amp itself. This result is being dominated by the last term in the equivalent input noise current expression. It is essential in this case to use a low voltage noise op amp. DESIGN-IN TOOLS DEMONSTRATION FIXTURES 1/(2R F C F ) = (GBP /(4R F C D )) Adding the common mode and differential mode input capacitance (0.7 + 2.8)pF to the 25pF diode source capacitance of Figure 3, and targeting a 50k transimpedance gain using the 230MHz GBP for the OPA656 will require a feedback pole set to 3.8MHz. This will require a total feedback capacitance of 0.8pF. Typical surface-mount resistors have a parasitic capacitance of 0.2pF leaving the required 0.6pF value shown in Figure 3 to get the required feedback pole. This will give an approximate -3dB bandwidth set by: Two printed circuit boards (PCBs) are available to assist in the initial evaluation of circuit performance using the OPA656 in its two package options. Both of these are offered free of charge as unpopulated PCBs, delivered with a user's guide. The summary information for these fixtures is shown in Table I. PRODUCT PACKAGE ORDERING NUMBER LITERATURE NUMBER OPA656U OPA656N SO-8 SOT23-5 DEM-OPA-SO-1A DEM-OPA-SOT-1A SBOU009 SBOU010 TABLE I. Demonstration Fixtures by Package. f-3dB = GBP / 2R F C D ) Hz The example of Figure 3 will give approximately 5.7MHz flat bandwidth using the 0.6pF feedback compensation. The demonstration fixtures can be requested at the Texas Instruments web site (www.ti.com) through the OPA656 product folder. OPA656 SBOS196G www.ti.com 11 OPERATING SUGGESTIONS FREQUENCY RESPONSE CONTROL SETTING RESISTOR VALUES TO MINIMIZE NOISE The OPA656 provides a very low input noise voltage while requiring a low 14mA quiescent supply current. To take full advantage of this low input noise, careful attention to the other possible noise contributors is required. Figure 4 shows the op amp noise analysis model with all the noise terms included. In this model, all the noise terms are taken to be noise voltage or current density terms in either nV/ Hz or pA/ Hz . ENI * ERS EO OPA656 RS IBN * RF 4kTRS 4kT RG * RG 4kTRF IBI 4kT = 1.6E -20J at 290K FIGURE 4. Op Amp Noise Analysis Model. The total output spot noise voltage can be computed as the square root of the squared contributing terms to the output noise voltage. This computation is adding all the contributing noise powers at the output by superposition, then taking the square root to get back to a spot noise voltage. Equation 1 shows the general form for this output noise voltage using the terms shown in Figure 4. (1) 2 2 EO = ENI2 + (IBNRS ) + 4kTRS NG2 + (IBIRF ) + 4kTRFNG Dividing this expression by the noise gain (GN = 1+RF/RG) will give the equivalent input referred spot noise voltage at the noninverting input as shown in Equation 2. (2) 2 4kTRF 2 I R EN = ENI2 + (IBNRS ) + 4kTRS + BI F + NG NG Putting high resistor values into Equation 2 can quickly dominate the total equivalent input referred noise. A source impedance on the noninverting input of 3k will add a Johnson voltage noise term equal to just that for the amplifier itself (7nV/ Hz). While the JFET input of the OPA656 is ideal for high source impedance applications, both the overall bandwidth and noise will be limited by higher source impedances in the noninverting configuration of Figure 1. 12 Voltage-feedback op amps like the OPA656 exhibit decreasing signal bandwidth as the signal gain is increased. In theory, this relationship is described by the GBP shown in the Electrical Characteristics. Ideally, dividing GBP by the noninverting signal gain (also called the Noise Gain, or NG) will predict the closed-loop bandwidth. In practice, this only holds true when the phase margin approaches 90, as it does in high-gain configurations. At low gains (increased feedback factors), most high-speed amplifiers will exhibit a more complex response with lower phase margin. The OPA656 is compensated to give a maximally flat 2nd-order Butterworth closed loop response at a noninverting gain of +2 (Figure 1). This results in a typical gain of +2 bandwidth of 200MHz, far exceeding that predicted by dividing the 230MHz GBP by 2. Increasing the gain will cause the phase margin to approach 90 and the bandwidth to more closely approach the predicted value of (GBP/NG). At a gain of +10 the OPA656 will show the 23MHz bandwidth predicted using the simple formula and the typical GBP of 230MHz. Unity-gain stable op amps like the OPA656 can also be bandlimited using a capacitor across the feedback resistor. For the noninverting configuration of Figure 1, a capacitor across the feedback resistor will decrease the gain with frequency down to a gain of +1. For instance, to bandlimit the gain of +2 design to 20MHz, a 32pF capacitor can be placed in parallel with the 250 feedback resistor. This will, however, only decrease the gain from 2 to 1. Using a feedback capacitor to limit the signal bandwidth is more effective in the inverting configuration of Figure 2. Adding that same capacitor to the feedback of Figure 2 will set a pole in the signal frequency response at 20MHz, but in this case it will continue to attenuate the signal gain to below 1. However, the output noise contribution due the input voltage noise of the OPA656 will still only be reduced to a gain of 1 with the addition of the feedback capacitor. DRIVING CAPACITIVE LOADS One of the most demanding and yet very common load conditions for an op amp is capacitive loading. Often, the capacitive load is the input of an ADC--including additional external capacitance which may be recommended to improve ADC linearity. A high-speed, high open-loop gain amplifier like the OPA656 can be very susceptible to decreased stability and closed-loop response peaking when a capacitive load is placed directly on the output pin. When the amplifier's open loop output resistance is considered, this capacitive load introduces an additional pole in the signal path that can decrease the phase margin. Several external solutions to this problem have been suggested. When the primary considerations are frequency response flatness, pulse response fidelity and/or distortion, the simplest and most effective solution is to isolate the capacitive load from the feedback loop by inserting a series isolation resistor between OPA656 www.ti.com SBOS196G the amplifier output and the capacitive load. This does not eliminate the pole from the loop response, but rather shifts it and adds a zero at a higher frequency. The additional zero acts to cancel the phase lag from the capacitive load pole, thus increasing the phase margin and improving stability. The Typical Characteristics show the recommended RS versus Capacitive Load and the resulting frequency response at the load. In this case, a design target of a maximally flat frequency response was used. Lower values of RS may be used if some peaking can be tolerated. Also, operating at higher gains (than the +2 used in the Typical Characteristics) will require lower values of RS for a minimally peaked frequency response. Parasitic capacitive loads greater than 2pF can begin to degrade the performance of the OPA656. Long PC board traces, unmatched cables, and connections to multiple devices can easily cause this value to be exceeded. Always consider this effect carefully, and add the recommended series resistor as close as possible to the OPA656 output pin (see Board Layout section). DISTORTION PERFORMANCE The OPA656 is capable of delivering a low distortion signal at high frequencies over a wide range of gains. The distortion plots in the Typical Characteristics show the typical distortion under a wide variety of conditions. Generally, until the fundamental signal reaches very high frequencies or powers, the 2nd-harmonic will dominate the distortion with negligible 3rd-harmonic component. Focusing then on the 2nd-harmonic, increasing the load impedance improves distortion directly. Remember that the total load includes the feedback network--in the noninverting configuration this is sum of RF + RG, while in the inverting configuration this is just RF (see Figure 1). Increasing output voltage swing increases harmonic distortion directly. A 6dB increase in output swing will generally increase the 2nd-harmonic 12dB and the 3rd-harmonic 18dB. Increasing the signal gain will also increase the 2nd-harmonic distortion. Again a 6dB increase in gain will increase the 2nd- and 3rd-harmonic by about 6dB even with a constant output power and frequency. And finally, the distortion increases as the fundamental frequency increases due to the rolloff in the loop gain with frequency. Conversely, the distortion will improve going to lower frequencies down to the dominant open loop pole at approximately 100kHz. Starting from the -70dBc 2nd-harmonic for a 5MHz, 2VPP fundamental into a 200 load at G = +2 (from the Typical Characteristics), the 2nd-harmonic distortion for frequencies lower than 100kHz will be < -105dBc. The OPA656 has an extremely low 3rd-order harmonic distortion. This also shows up in the 2-tone 3rd-order intermodulation spurious (IM3) response curves. The 3rd-order spurious levels are extremely low (< -80dBc) at low output power levels. The output stage continues to hold them low even as the fundamental power reaches higher levels. As the Typical Characteristics show, the spurious intermodulation powers do not increase as predicted by a traditional intercept model. As the fundamental power level increases, the dynamic range does not decrease significantly. For 2 tones centered at 10MHz, with 4dBm/tone into a matched 50 load (that is, 1VPP for each tone at the load, which requires 4VPP for the overall 2-tone envelope at the output pin), the Typical Characteristics show a 78dBc difference between the test tone and the 3rd-order intermodulation spurious levels. This exceptional performance improves further when operating at lower frequencies and/or higher load impedances. DC ACCURACY AND OFFSET CONTROL The OPA656 can provide excellent DC accuracy due to its high open-loop gain, high common-mode rejection, high power-supply rejection, and its trimmed input offset voltage (and drift) along with the negligible errors introduced by the low input bias current. For the best DC precision, a highgrade version (OPA656UB or OPA656NB) screens the key DC parameters to an even tighter limits. Both standard- and high-grade versions take advantage of a new final test technique to 100% test input offset voltage drift over temperature. This discussion will use the high-grade typical and min/max electrical characteristics for illustration; however, an identical analysis applies to the standard-grade version. The total output DC offset voltage in any configuration and temperature will be the combination of a number of possible error terms. In a JFET part like the OPA656, the input bias current terms are typically quite low but are unmatched. Using bias current cancellation techniques, more typical in bipolar input amplifiers, does not improve output DC offset errors. Errors due to the input bias current will only become dominant at elevated temperatures. The OPA656 shows the typical 2x increase in every 10C common to JFET-input stage amplifiers. Using the 5pA maximum tested value at 25C, and a 20C internal self heating (see thermal analysis), the maximum input bias current at 85C ambient will be 5pA * 2(105 - 25)/10 = 1280pA. For noninverting configurations, this term only begins to be a significant term versus the input offset voltage for source impedances > 750k. This would also be the feedback-resistor value for transimpedance applications (see Figure 3) where the output DC error due to inverting input bias current is on the order of that contributed by the input offset voltage. In general, except for these extremely high impedance values, the output DC errors due to the input bias current may be neglected. After the input offset voltage itself, the most significant term contributing to output offset voltage is the PSRR for the negative supply. This term is modeled as an input offset voltage shift due to changes in the negative power-supply voltage (and similarly for the +PSRR). The high-grade test limit for -PSRR is 62dB. This translates into 1.59mV/V input offset voltage shift = 10(-62/20). In the worst case, a 0.38V (7.6%) shift in the negative supply voltage will produce a 0.6mV apparent input offset voltage shift. Since this is comparable to the tested limit of 0.6mV input offset voltage, OPA656 SBOS196G www.ti.com 13 a careful control of the negative supply voltage is required. The +PSRR is tested to a minimum value of 74dB. This translates into 10(-74/20) = 0.2mV/V sensitivity for the input offset voltage to positive power supply changes. As an example, compute the worst-case output DC error for the transimpedance circuit of Figure 1 at 25C and then the shift over the 0C to 70C range given the following assumptions. Negative Power Supply = -5V 0.2V with a 5mV/C worst-case shift Positive Power Supply = +5V 0.2V with a 5mV/C worst-case shift Initial 25C Output DC Error Band = 0.3mV (due to the -PSRR = 1.59mV/V * 0.2V) 0.04mV (due to the +PSRR = 0.2mV/V * 0.2V) 0.6mV Input Offset Voltage The OPA656 will not require heatsinking or airflow in most applications. Maximum allowed junction temperature will set the maximum allowed internal power dissipation as described below. In no case should the maximum junction temperature be allowed to exceed 150C. Operating junction temperature (TJ) is given by TA + PD * JA. The total internal power dissipation (PD) is the sum of quiescent power (PDQ) and additional power dissipated in the output stage (PDL) to deliver load power. Quiescent power is simply the specified no-load supply current times the total supply voltage across the part. PDL will depend on the required output signal and load but would, for a grounded resistive load, be at a maximum when the output is fixed at a voltage equal to 1/2 of either supply voltage (for equal bipolar supplies). Under this condition PDL = VS2/(4 * RL) where RL includes feedback network loading. Note that it is the power in the output stage and not into the load that determines internal power dissipation. Total = 0.94mV This would be the worst-case error band in volume production at 25C acceptance testing given the conditions stated. Over the temperature range of 0C to 70C, we can expect the following worst-case shifting from initial value. A 20C internal junction self heating is assumed here. As a worst-case example, compute the maximum TJ using an OPA656N (SOT23-5 package) in the circuit of Figure 1 operating at the maximum specified ambient temperature of +85C and driving a grounded 100 load. PD = 10V * 16.1mA + 52 /(4 * (100 || 800)) = 231mW Maximum TJ = +85C + (0.23W * 150C/W) = 120C. 0.36mV (OPA656 high-grade input offset drift) = 6V/C * (70C + 20C - 25C)) 0.23mV (-PSRR of 60dB with 5mV * (70C - 25C) supply shift) 0.06mV (+PSRR of 72dB with 5mV * (70C - 25C) supply shift) Total = 0.65mV This would be the worst-case shift from initial offset over a 0C to 70C ambient for the conditions stated. Typical initial output DC error bands and shifts over temperature will be much lower than these worst-case estimates. In the transimpedance configuration, the CMRR errors can be neglected since the input common mode voltage is held at ground. For noninverting gain configurations (see Figure 1), the CMRR term will need to be considered but will typically be far lower than the input offset voltage term. With a tested minimum of 80dB (100V/V), the added apparent DC error will be no more than 0.2mV for a 2V input swing to the circuit of Figure 1. POWER-SUPPLY CONSIDERATIONS The OPA656 is intended for operation on 5V supplies. Single-supply operation is allowed with minimal change from the stated specifications and performance from a single supply of +8V to +12V maximum. The limit to lower supply voltage operation is the useable input voltage range for the JFET-input stage. Operating from a single supply of +12V can have numerous advantages. With the negative supply at ground, the DC errors due to the -PSRR term can be minimized. Typically, AC performance improves slightly at +12V operation with minimal increase in supply current. 14 THERMAL ANALYSIS All actual applications will be operating at lower internal power and junction temperature. BOARD LAYOUT Achieving optimum performance with a high-frequency amplifier like the OPA656 requires careful attention to board layout parasitics and external component types. Recommendations that will optimize performance include: a) Minimize parasitic capacitance to any AC ground for all of the signal I/O pins. Parasitic capacitance on the output and inverting input pins can cause instability--on the noninverting input, it can react with the source impedance to cause unintentional bandlimiting. To reduce unwanted capacitance, a window around the signal I/O pins should be opened in all of the ground and power planes around those pins. Otherwise, ground and power planes should be unbroken elsewhere on the board. b) Minimize the distance (< 0.25") from the power-supply pins to high-frequency 0.1uF decoupling capacitors. At the device pins, the ground and power plane layout should not be in close proximity to the signal I/O pins. Avoid narrow power and ground traces to minimize inductance between the pins and the decoupling capacitors. The power-supply connections should always be decoupled with these capacitors. Larger (2.2F to 6.8F) decoupling capacitors, effective at lower frequency, should also be used on the supply pins. These may be placed somewhat farther from the device and may be shared among several devices in the same area of the PC board. OPA656 www.ti.com SBOS196G c) Careful selection and placement of external components will preserve the high frequency performance of the OPA656. Resistors should be a very low reactance type. Surface-mount resistors work best and allow a tighter overall layout. Metal film and carbon composition axially leaded resistors can also provide good high frequency performance. Again, keep their leads and PCB trace length as short as possible. Never use wirewound type resistors in a high frequency application. Since the output pin and inverting input pin are the most sensitive to parasitic capacitance, always position the feedback and series output resistor, if any, as close as possible to the output pin. Other network components, such as noninverting input termination resistors, should also be placed close to the package. Where double side component mounting is allowed, place the feedback resistor directly under the package on the other side of the board between the output and inverting input pins. Even with a low parasitic capacitance shunting the external resistors, excessively high resistor values can create significant time constants that can degrade performance. Good axial metal film or surfacemount resistors have approximately 0.2pF in shunt with the resistor. For resistor values > 1.5k, this parasitic capacitance can add a pole and/or zero below 500MHz that can effect circuit operation. Keep resistor values as low as possible consistent with load driving considerations. It has been suggested here that a good starting point for design would be to keep RF || RG < 250 for voltage amplifier applications. Doing this will automatically keep the resistor noise terms low, and minimize the effect of their parasitic capacitance. Transimpedance applications (see Figure 3) can use whatever feedback resistor is required by the application as long as the feedback compensation capacitor is set considering all parasitic capacitance terms on the inverting node. based on board material and trace dimensions, a matching series resistor into the trace from the output of the OPA656 is used as well as a terminating shunt resistor at the input of the destination device. Remember also that the terminating impedance will be the parallel combination of the shunt resistor and the input impedance of the destination device-- this total effective impedance should be set to match the trace impedance. If the 6dB attenuation of a doubly-terminated transmission line is unacceptable, a long trace can be series-terminated at the source end only. Treat the trace as a capacitive load in this case and set the series resistor value as shown in the plot of Recommended RS vs Capacitive Load. This will not preserve signal integrity as well as a doubly-terminated line. If the input impedance of the destination device is low, there will be some signal attenuation due to the voltage divider formed by the series output into the terminating impedance. d) Connections to other wideband devices on the board may be made with short direct traces or through onboard transmission lines. For short connections, consider the trace and the input to the next device as a lumped capacitive load. Relatively wide traces (50mils to 100mils) should be used, preferably with ground and power planes opened up around them. Estimate the total capacitive load and set RS from the plot of Recommended RS vs Capacitive Load. Low parasitic capacitive loads (< 5pF) may not need an RS since the OPA656 is nominally compensated to operate with a 2pF parasitic load. Higher parasitic capacitive loads without an RS are allowed as the signal gain increases (increasing the unloaded phase margin) If a long trace is required, and the 6dB signal loss intrinsic to a doubly-terminated transmission line is acceptable, implement a matched impedance transmission line using microstrip or stripline techniques (consult an ECL design handbook for microstrip and stripline layout techniques). A 50 environment is normally not necessary onboard, and in fact a higher impedance environment will improve distortion as shown in the distortion versus load plots. With a characteristic board trace impedance defined These diodes provide moderate protection to input overdrive voltages above the supplies as well. The protection diodes can typically support 30mA continuous current. Where higher currents are possible (for example, in systems with 12V supply parts driving into the OPA656), current limiting series resistors should be added into the two inputs. Keep these resistor values as low as possible since high values degrade both noise performance and frequency response. e) Socketing a high speed part like the OPA656 is not recommended. The additional lead length and pin-to-pin capacitance introduced by the socket can create an extremely troublesome parasitic network which can make it almost impossible to achieve a smooth, stable frequency response. Best results are obtained by soldering the OPA656 onto the board. INPUT AND ESD PROTECTION The OPA656 is built using a very high speed complementary bipolar process. The internal junction breakdown voltages are relatively low for these very small geometry devices. These breakdowns are reflected in the Absolute Maximum Ratings table. All device pins are protected with internal ESD protection diodes to the power supplies as shown in Figure 5. +V CC External Pin -V CC FIGURE 5. Internal ESD Protection. OPA656 SBOS196G Internal Circuitry www.ti.com 15 Revision History DATE REVISION 11/08 G 3/06 F PAGE SECTION 2 Abs Max Ratings 3 Electrical Characteristics 11 Design-In Tools DESCRIPTION Changed Storage Temperature Range from -40C to +125C to -65C to +125C. DC Performance section; deleted Drift from Input Offset Current specifications. Added Design-In Tools paragraph and table. NOTE: Page numbers for previous revisions may differ from page numbers in the current version. 16 OPA656 www.ti.com SBOS196G PACKAGE OPTION ADDENDUM www.ti.com 26-May-2010 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) Samples (Requires Login) OPA656N/250 ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Request Free Samples OPA656N/250G4 ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Request Free Samples OPA656NB/250 ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Request Free Samples OPA656NB/250G4 ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Request Free Samples OPA656U ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR Request Free Samples OPA656U/2K5 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR Purchase Samples OPA656U/2K5G4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR Purchase Samples OPA656UB ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR Request Free Samples OPA656UB/2K5 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR Purchase Samples OPA656UB/2K5G4 PREVIEW SOIC D 8 Call TI Samples Not Available OPA656UBG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR Request Free Samples OPA656UG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR Request Free Samples TBD Call TI (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Addendum-Page 1 PACKAGE OPTION ADDENDUM www.ti.com 26-May-2010 Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) OPA656N/250 SOT-23 DBV 5 250 180.0 OPA656NB/250 SOT-23 DBV 5 250 OPA656U/2K5 SOIC D 8 2500 OPA656UB/2K5 SOIC D 8 2500 B0 (mm) K0 (mm) P1 (mm) 8.4 3.2 3.1 1.39 4.0 180.0 8.4 3.2 3.1 1.39 330.0 12.4 6.4 5.2 2.1 330.0 12.4 6.4 5.2 2.1 Pack Materials-Page 1 W Pin1 (mm) Quadrant 8.0 Q3 4.0 8.0 Q3 8.0 12.0 Q1 8.0 12.0 Q1 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) OPA656N/250 SOT-23 DBV 5 250 210.0 185.0 35.0 OPA656NB/250 SOT-23 DBV 5 250 210.0 185.0 35.0 OPA656U/2K5 SOIC D 8 2500 367.0 367.0 35.0 OPA656UB/2K5 SOIC D 8 2500 367.0 367.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated