Thyristors Surface Mount - 100V -600V > MCR70xA Series MCR70xA Series Pb Description PNPN Componants designed for high volume, low cost consumer applications such as temperature, light and speed control; process and remote control; and warning systems where reliability of operation is critical. Features * Small Size * Passivated Die Surface for Reliability and Uniformity * Low Level Triggering and Holding Characteristics * Recommend Electrical Replacement for C106 * Surface Mount Package - Case 369C * To Obtain "DPAK" in Straight Lead Version (Shipped in Sleeves): Add '1' Suffix to Componant Number, i.e., MCR706A1 Pin Out * UL Recognized compound meeting flammability 4 4 1 2 rating V-0. * ESD Ratings: Human Body Model, 3B > 8000 V Machine Model, C > 400 V * Pb-Free Packages are Available 3 1 2 3 Functional Diagram G A K Additional Information Datasheet Resources Samples (c) 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/15/18 Thyristors Surface Mount - 100V -600V > MCR70xA Series Maximum Ratings (TJ = 25C unless otherwise noted) Rating MCR703A Peak Repetitive Off-State Voltage (Note 1) (TC = - 40 to +110C, Sine Wave, 50 to 60 Hz, RGK = 1 k ) MCR706A Symbol Value VDRM, 100 VRRM MCR708A VDSM MCR706A (180 Conduction Angles; TC = 85C) Average On-State Current TC = -40 to +90C (180 Conduction Angles) TC = +100C 450 V 650 MCR708A On-State RMS Current (180 Conduction Angles; TC = 90C) V 600 150 MCR703A Peak Non-Repetitive Off-State Voltage 400 Unit IT(RMS) IT(AV) Non-Repetitive Surge Current 4.0 2.6 1.6 A A ITSM 25 Circuit Fusing Consideration (t = 8.3 ms) I2t 2.6 Asec Forward Peak Gate Power (Pulse Width 1.0 sec, TC= 90C) IGM 0.5 W Forward Peak Gate Current (Pulse Width 1.0 sec, TC= 90C) PGM 0.2 A Forward Average Gate Power (t = 8.3 ms, TC = 90C) PG(AV) 0.1 W Operating Junction Temperature Range TJ -40 to +110 C Storage Temperature Range Tstg -40 to +150 C (1/2 Cycle, Sine Wave 60 Hz, TJ = 110C) (1/2 Cycle, Sine Wave 1.5 ms, TJ = 110C) A 35 Stresses exceeding Maximum Ratings may damage the Componant. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect Componant reliability. 1. VDRM and VRRM for all types can be applied on a continuous basis. Ratings apply for zero or negative gate voltage; however, positive gate voltage shall not be applied concurrent with negative potential on the anode. Blocking voltages shall not be tested with a constant current source such that the voltage ratings of the Componants are exceeded. Thermal Characteristics* Rating Symbol Value Thermal Resistance, Junction-to-Case RJC 3.0 Thermal Resistance, Junction-to-Ambient (Note 2) RJA 80 TL 260 Maximum Lead Temperature for Soldering Purposes 1/8" from Case for 10 Seconds Unit C/W C 2. Case 369C when surface mounted on minimum pad sizes recommended. (c) 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/15/18 Thyristors Surface Mount - 100V -600V > MCR70xA Series Electrical Characteristics - OFF (TJ = 25C unless otherwise noted) Characteristic Peak Repetitive Forward or Reverse Blocking Current (VAK = Rated VDRM or VRRM, RGK = 1 k ) Symbol Min Typ Max TJ = 25C IDRM, - - 10 TJ = 110C IRRM - - 200 Unit A Electrical Characteristics - ON (TJ = 25C unless otherwise noted) Characteristic Symbol Min Typ Max Unit VTM _ _ 2.2 V _ 25 75 Peak Forward "On" Voltage (ITM = 8.2 A Peak, Pulse Width = 1 to 2 ms, 2% Duty Cycle) Gate Trigger Current (Continuous dc) (Note 3) (VAK = 12 V; RL = 24 ) Gate Trigger Voltage (Continuous dc) (Note 3) (VAK = 12 V; RL = 24 ) TJ = 25C IGT A TJ = -40C TJ = 25C _ _ 300 _ _ 0.8 VGT V TJ = -40C _ _ 1.0 VGD 0.2 _ _ V IH - _ - - 5.0 10 mA Peak Reverse Gate Blocking Voltage (IGR = 10 A) VRGM 10 12.5 18 V Peak Reverse Gate Blocking Current (VGR = 10 V) IRGM _ _ 1.2 A tgt _ 2.0 _ s Gate Non-Trigger Voltage (Note 3) (VAK= 12 Vdc; RL = 100 , TC =110) Holding Current (VAK = 12 Vdc, RGK = 1 k ) TC = 25C (Initiating Current = 20 mA) TC = -40C Total Turn-On Time (Source Voltage = 12 V, RS = 6 kQ) (ITM = 8.2 A, IGT = 2 mA, Rated VDRM) (Rise Time = 20 ns, Pulse Width = 10 s) Dynamic Characteristics* Characteristic Symbol Min Typ Max Unit Critical Rate of Rise of Off-State Voltage (VD = Rated VDRM, RGK = 1 k , Exponential Waveform, Gate Open, Tc = 110C) dv/dt - 10 - V/s Repetitive Critical Rate of Rise of On-State Current (Cf = 60 Hz, IPK = 30 A, PW = 100 s, diG/dt = 1 A/s) di/dt - - 100 A/s 3. RGK current not included in measurement. (c) 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/15/18 Thyristors Surface Mount - 100V -600V > MCR70xA Series Voltage Current Characteristic of SCR Symbol Parameter VDRM Peak Repetitive Forward Off State Voltage IDRM Peak Forward Blocking Current Anode + VTM VRRM Peak Repetitive Reverse Off State Voltage IRRM Peak Reverse Blocking Current VTM Maximum On State Voltage IH +Current Holding Current Figure 1. RMS Current Derating on state +Voltage IDRM at VDRM Reverse Blocking Region (off state) Forward Blocking Region (off state) Reverse Avalanche Region Anode Figure 2. On-State Power Dissipation Conduction Angle Conduction Angle Figure 4. Transient Thermal Response r(t), TRANSIEN T RESIST ANCE (NORMALIZED) Figure 3. On-State Characteristics IH IRRM at VRRM 1.0 Z JC(t) = R JC(t)* r(t) 0.1 0.01 0.1 1.0 10 100 1000 t, TIME (ms) (c) 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/15/18 10,000 Thyristors Surface Mount - 100V -600V > MCR70xA Series Figure 5. Typical Gate Trigger Current vs Junction Temperature Figure 6. Typical Gate Trigger Voltage vs Junction Temperature 1.0 VGT, GATE TRIGGER VOLTAGE (VOLTS) I GT, GATE TRIGGER CURRENT ( A) 35 30 25 20 15 -40 -20 0 20 40 60 80 0.5 0 100 110 -40 -20 TJ , JUNCTION TEMPERA TURE (C) Figure 7. Typical Holding Current vs Junction Temperature 40 60 80 100 110 2.0 IL , LATCHING CURRENT (mA) IH, HOLDING CURRENT (mA) 0 20 Figure 8. Typical Latching Current vs Junction Temperature 2.0 1.5 1.0 0.5 0 -40 002 TJ , JUNCTION TEMPERA TURE (C) -200 -20 0 20 40 60 TJ , JUNCTION TEMPERA TURE (C) 80 100 110 1.5 1.0 0.5 0 -40 -200 20 40 60 80 100 110 TJ , JUNCTION TEMPERA TURE (C) (c) 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/15/18 Thyristors Surface Mount - 100V -600V > MCR70xA Series Soldering Footprint Dimensions DPAK CASE 369C 01 ISSUE A 6.20 0.244 2.58 0.101 SEATING PLANE T C B V 5.80 0.228 1.6 0.063 6.172 0.243 E R 4 Z A S 3.0 0.118 12 3 J L H D G 2 PL 0.13 (0.005) Dim M T Inches Millimeters Min Max Min Max A 0.086 0.094 2.18 2.38 A1 0.000 0.005 0.00 0.13 b 0.025 0.035 0.63 0.89 b2 0.030 0.045 0.76 1.14 b3 0.180 0.215 4.57 5.46 c 0.018 0.024 0.46 0.61 c2 0.018 0.024 0.46 0.61 D 0.235 0.245 5.97 6.22 E 0.250 0.265 6.35 6.73 e 0.090 BSC 2.29 BSC H 0.370 0.410 9.40 10.41 L 0.055 0.070 1.40 1.78 L1 L2 mm inches U K F SCALE 3:1 0.108 REF 0.020 BSC 2.74 REF 0.51 BSC L3 0.035 0.050 0.89 1.27 L4 --- 0.040 --- 1.01 Z 0.155 --- 3.93 --- 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION Z DEFINES A ZONE WHERE ALL BODY AND LEAD IRREGULARITIES ARE ALLOWED. (c) 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/15/18 Thyristors Surface Mount - 100V -600V > MCR70xA Series Part Marking System Dimensions DPAK 3 CASE 369D 01 ISSUE B 1 2 4 12 Z A 3 1 2 3 T SEATING PLANE K J F D G Dim YWW CR 70xAG DPAK 3 CASE 369D STYLE 5 YWW CR 70xAG Y = Year WW = Work Week Code 70xA = Componant x = 3, 6 or 8 G = Pb-Free Package H 3 PL 0.13 (0.005) DPAK CASE 369C STYLE 5 4 E R S 3 C B V 4 M Pin Assignment T Inches Millimeters 1 Gate 2 Anode 3 Cathode 4 Anode Min Max Min Max A 0.235 0.245 5.97 6.35 B 0.250 0.265 6.35 6.73 C 0.086 0.094 2.19 2.38 Componant D 0.027 0.035 0.69 0.88 MCR703AT4 369C E 0.018 0.023 0.46 0.58 F 0.037 0.045 0.94 1.14 MCR703AT4G 369C (Pb-Free) G 0.090 BSC 2.29 BSC H 0.034 0.040 0.87 1.01 J 0.018 0.023 0.46 0.58 K 0.350 0.380 8.89 9.65 R 0.180 0.215 4.45 5.45 S 0.025 0.040 0.63 1.01 V 0.035 0.050 0.89 1.27 Z 0.155 --- 3.93 --- 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. Ordering Information Package MCR706AT4 Shipping 369C DPAK MCR706AT4G 369C (Pb-Free) MCR708A 369C MCR708AG 369C (Pb-Free) MCR708A1 369D DPAK-3 MCR708A1G MCR708AT4 MCR708AT4G 75 Units/ Rail 369D (Pb-Free) 369C DPAK 2500 Tape & Reel 369C (Pb-Free) 2500 Tape & Reel Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at: www.littelfuse.com/disclaimer-electronics (c) 2018 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 05/15/18