REVISIONS LTR A B DESCRIPTION DATE APPROVED Added ebanol and nickel plate finishes. Editorial changes throughout. Updated referenced documents and contact information. Technical and editorial changes throughout. 12 JUN 1989 Randy Larson 14 SEP 2001 Thomas Hess PREVIOUS CAGE CODE 14933 SUPERSEDED BY 037Z3. THE ORIGINAL FIRST PAGE OF THIS DRAWING HAS BEEN REPLACED. Prepared in accordance with MIL-STD-100 Selected item drawing REV PAGE REV PAGE REV STATUS OF PAGES PMIC N/A REV B B B B B B B B B B B B B B PAGES 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PREPARED BY James B. Walker Jr. DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH Original date of drawing 23 October 1988 CHECKED BY Ken Beymer TITLE HOLDER, ELECTRICAL CARD, CARD GUIDERETAINER, SCREW ACTUATED, METAL APPROVED BY D. E. Morgan SIZE A REV CODE IDENT. NO. DWG NO. 14933 B 88052 PAGE 1 OF AMSC N/A DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. 14 5998-E033 1. SCOPE 1.1 Scope. This drawing describes the requirements for a family of lever actuated card guides intended for use with printed circuit boards and circuit card assemblies in moderate shock and vibration environments. 1.2 Part or Identifying Number (PIN). The complete PIN shall be as follows: -XXX Dash number (see table I) 88052 Drawing number E Housing finish (see 3.2.1) 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the solicitation (see 6.2). SPECIFICATIONS FEDERAL QQ-N-290 QQ-P-416 - Nickel Plating ((Electrodeposited). Plating, Cadmium (Electrodeposited). DEPARTMENT OF DEFENSE MIL-F-495 MIL-S-5002 MIL-DTL-13924 - Finish, Chemical, Black, for Copper Alloys. Surface Treatments and Inorganic Coatings for Metal Surfaces of Weapon Systems. Coating, Oxide, Black, For Ferrous Metals. STANDARDS DEPARTMENT OF DEFENSE MIL-STD-1285 - Marking of Electrical and Electronic Parts. (Unless otherwise indicated, copies of federal and military specifications, standards, and handbooks are available from the Document Automation and Production Service (DAPS), Building 4D (DPM-DODSSP), 700 Robbins Avenue, Philadelphia, PA 19111-5094.) 2.2 Non-Government publications. The following document(s) form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DoD adopted are those listed in the issue of the DoDISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the DoDISS are the issues of the documents cited in the solicitation (see 6.2). AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) ASTM A366 - ASTM A582 ASTM B194 - Standard Specification for Commercial Steel (CS) Sheet, Carbon, (0.15 Maximum Percent), Cold-Rolled. Standard Specification for Free-Machining Stainless Steel Bars. Standard Specification for Copper-Beryllium Alloy Plate, Sheet, Strip, and Rolled Bar. (Application for copies should be addressed to the American Society for Testing and Materials, 100 Barr Harbor Drive, West Coshohocken, PA 19428-2959.) DEFENSE SUPPLY CENTER, COLUMBUS SIZE CODE IDENT NO. DWG NO. COLUMBUS, OHIO A 14933 88052 REV B PAGE 2 (Non-Government Standards and other publications are normally available from the organizations which prepare or which distribute the documents. These documents also may be available in or through libraries or other informational services.) 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Interface and physical dimensions. See table I and figure 1. 3.2 Materials. 3.2.1 Housing. The body material shall be cold rolled steel in accordance with ASTM A366 or beryllium copper in accordance with ASTM B194. 3.2.2 Cam. The cam material shall be beryllium copper housing material in accordance with ASTM A366. 3.2.3 Screw. The screw material shall be stainless steel in accordance with ASTM A582. 3.3 Finish. 3.3.1 Housing. The finish shall be cadmium plate in accordance with QQ-P-416, type II, class 2 or ebanol in accordance with MIL-F-495 (for beryllium copper) or MIL-DTL-13924 (for steel) or nickel plate in accordance with QQ-N-290, class 1, grade G (bright). Parts with a cadmium plated finish shall include a suffix "C", parts with an ebanol finish shall include a suffix "E", and parts with a nickel plated finish shall include a suffix "N" (see 1.2). 3.3.2 Screw. The screw shall be passivate in accordance with MIL-S-5002. 3.4 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be a suggested source of supply. 3.5 Marking. Marking of the card guide is not required; however, each unit package shall be marked in accordance with MIL-STD-1285 and include the PIN as specified herein (see 1.2), the manufacturer's name or Commercial and Government Entity (CAGE) code, and date lot codes. 3.6 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.7 Workmanship. Card holders shall be processed in such a manner as to be uniform in quality and shall be free from surface and finish flaws that could affect life or serviceability. Burrs, chipping, and cracking are unacceptable. 4. VERIFICATION 4.1 Sampling and inspection. Unless otherwise specified in the contract or purchase order, the contractor is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified in the contract, the contractor may use his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in this drawing where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements. 4.2 Conformance inspections. 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of visual and mechanical inspections of interface and physical dimensions (see 3.1), materials (see 3.2), and workmanship (see 3.7). Criteria for defects are listed in 4.2.5. 4.2.2 Optional statement of compliance. The acquiring activity, at its discretion, may accept a statement of compliance in lieu of the manufacturer performing the inspection of product for delivery (see 6.2.b). DEFENSE SUPPLY CENTER, COLUMBUS SIZE CODE IDENT NO. DWG NO. COLUMBUS, OHIO A 14933 88052 REV B PAGE 3 Board thickness A B .025 to .079 .09 .309 .080 to .145 .16 .376 FIGURE 1. Design and dimensions. DEFENSE SUPPLY CENTER, COLUMBUS SIZE CODE IDENT NO. DWG NO. COLUMBUS, OHIO A 14933 88052 REV B PAGE 4 FIGURE 1. Design and dimensions - Continued. DEFENSE SUPPLY CENTER, COLUMBUS SIZE CODE IDENT NO. DWG NO. COLUMBUS, OHIO A 14933 88052 REV B PAGE 5 Inches .001 .003 .005 .008 .02 .023 .067 .093 .165 .19 mm 0.25 0.67 0.13 0.20 0.51 0.58 1.70 2.36 4.19 4.8 Inches .196 .218 .250 .500 .67 .750 2.250 3.00 3.250 4.250 4.750 mm 4.98 5.54 6.35 12.70 17.0 19.05 57.15 76.2 82.55 107.95 120.65 Inches 5.00 5.250 5.50 6.00 6.250 6.750 7.00 7.250 7.50 8.00 12.00 mm 127.0 133.35 139.7 152.4 158.75 171.45 177.8 184.15 190.5 203.2 304.8 NOTES: 1. Dimensions are in inches. Metric equivalents are given for general information only. 2. Unless otherwise specified, tolerance is .02 inch (0.5 mm) for two place decimals and .010 (0.25 mm) for three place decimals. 3. Card guides between 3.00 and 4.5 inch in length have only two mounting holes. The hole dimensions are per the .500 inch datum 0 and the .250 reference illustrated on the 12.0 inch length card guide. FIGURE 1. Design and dimensions - Continued. DEFENSE SUPPLY CENTER, COLUMBUS SIZE CODE IDENT NO. DWG NO. COLUMBUS, OHIO A 14933 88052 REV B PAGE 6 TABLE I. Design and dimensions. Part Number 88052 -001 -002 -003 -004 -005 -006 -007 -008 -009 -010 -011 -012 -013 -014 -015 -016 -017 -018 -019 -020 -021 -022 -023 -024 -025 -026 -027 -028 -029 -030 -031 -032 -033 -034 -035 -036 -037 -038 -039 -040 Housing material B = beryllium copper S= Steel B S B S B S B S B S B S B S B S B S B S B S B S B S B S B S B S B S B S B S B S Board thickness (inches) A = .025 to .070 B = .087 to .132 A A B B A A B B A A B B A A B B A A B B A A B B A A B B A A B B A A B B A A B B "L" dimension inches (mm) 3.0 (76.2) " " " " " " " 3.5 (88.9) " " " " " " " 4.0 (101.6) " " " " " " " 4.5 (114.3) " " " " " " " 5.0 (127.0) " " " " " " " Action Left or right L = left R = right L L L L R R R R L L L L R R R R L L L L R R R R L L L L R R R R L L L L R R R R DEFENSE SUPPLY CENTER, COLUMBUS SIZE CODE IDENT NO. DWG NO. COLUMBUS, OHIO A 14933 88052 REV B PAGE 7 TABLE I. Design and dimensions -- Continued. PIN 88052 -041 -042 -043 -044 -045 -046 -047 -048 -049 -050 -051 -052 -053 -054 -055 -056 -057 -058 -059 -060 -061 -062 -063 -064 -065 -066 -067 -068 -069 -070 -071 -072 -073 -074 -075 -076 -077 -078 -079 -080 Housing material B = beryllium copper S= Steel B S B S B S B S B S B S B S B S B S B S B S B S B S B S B S B S B S B S B S B S Board thickness (inches) A = .025 to .070 B = .087 to .132 A A B B A A B B A A B B A A B B A A B B A A B B A A B B A A B B A A B B A A B B "L" Dimension Inches (mm) 5.5 (139.7) " " " " " " " 6.0 (152.4) " " " " " " " 7.0 (177.8) " " " " " " " 7.5 (190.5) " " " " " " " 8.5 (215.9) " " " " " " " Action Left or right L = left R = right L L L L R R R R L L L L R R R R L L L L R R R R L L L L R R R R L L L L R R R R DEFENSE SUPPLY CENTER, COLUMBUS SIZE CODE IDENT NO. DWG NO. COLUMBUS, OHIO A 14933 88052 REV B PAGE 8 TABLE I. Design and dimensions -- Continued. PIN 88052 -081 -082 -083 -084 -085 -086 -087 -088 -089 -090 -091 -092 -093 -094 -095 -096 -097 -098 -099 -100 -101 -102 -103 -104 -105 -106 -107 -108 -109 -110 -111 -112 -113 -114 -115 -116 -117 -118 -119 -120 Housing material B = beryllium copper S= Steel B S B S B S B S B S B S B S B S B S B S B S B S B S B S B S B S B S B S B S B S Board thickness (inches) A = .025 to .070 B = .087 to .132 A A B B A A B B A A B B A A B B A A B B A A B B A A B B A A B B A A B B A A B B "L" Dimension Inches (mm) 6.5 (165.1) " " " " " " " 8.0 (203.2) " " " " " " " 9.0 (228.6) " " " " " " " 9.5 (241.3) " " " " " " " 10.0 (254.0) " " " " " " " Action Left or right L = left R = right L L L L R R R R L L L L R R R R L L L L R R R R L L L L R R R R L L L L R R R R DEFENSE SUPPLY CENTER, COLUMBUS SIZE CODE IDENT NO. DWG NO. COLUMBUS, OHIO A 14933 88052 REV B PAGE 9 TABLE I. Design and dimensions -- Continued. PIN 88052 -121 -122 -123 -124 -125 -126 -127 -128 -129 -130 -131 -132 -133 -134 -135 -136 -137 -138 -139 -140 -141 -142 -143 -144 -145 -146 -147 -148 -149 -150 -151 -152 Housing material B = beryllium copper S= Steel B S B S B S B S B S B S B S B S B S B S B S B S B S B S B S B S Board thickness (inches) A = .025 to .070 B = .087 to .132 A A B B A A B B A A B B A A B B A A B B A A B B A A B B A A B B "L" Dimension Inches (mm) 10.5 (266.7) " " " " " " " 11.0 (279.4) " " " " " " " 11.5 (292.1) " " " " " " " 12.0 (304.8) " " " " " " " Action Left or right L = left R = right L L L L R R R R L L L L R R R R L L L L R R R R L L L L R R R R 4.2.3 Sampling plan. A sample of parts shall be randomly selected in accordance with table II, normal sampling. If one or more defects are found, the lot shall be rejected. Criteria for defects are listed in 4.2.5. 4.2.4 Rejected lots. If an inspection lot is rejected after normal sampling inspection, the manufacturer may rework it to correct the defects, or screen out the defective parts and resubmit for inspection. Resubmitted lots shall be inspected by selecting a random sample of parts in accordance with table II, tightened sampling. If one or more defects are found in this sample, the lot shall be rejected and shall not be supplied to this specification. Resubmitted lots which are acceptable shall be clearly identified as reinspected lots. DEFENSE SUPPLY CENTER, COLUMBUS SIZE CODE IDENT NO. DWG NO. COLUMBUS, OHIO A 14933 88052 REV B PAGE 10 TABLE II. Sampling plan. Lot size Normal Tightened 2 to 25 3 5 26 to 50 5 6 51 to 90 6 7 91 to 150 7 11 151 to 280 10 13 281 to 500 11 16 501 to 1,200 15 19 1,201 to 3,200 18 23 3,201 to 10,000 22 29 10,001 to 35,001 29 35 29 40 35,001 and over 4.2.5 Defective characteristics and properties. Dimensional characteristics are considered defective when out of tolerance. Physical and functional properties are considered defective when outside the specified minimum, maximum, or range as applicable. Workmanship characteristics are considered defective when they would be detrimental to the intended use, performance requirements, or environmental survival of the part. 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When actual packaging of materiel is to be performed by DoD personnel, these personnel need to contact the responsible packaging activity to ascertain requisite packaging requirements. Packaging requirements are maintained by the Inventory Control Point's packaging activity within the Military Department or Defense Agency, or within the Military Department's System Command. Packaging data retrieval is available from the managing Military Department's or Defense Agency's automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general or explanatory nature which may be helpful, but is not mandatory.) 6.1 Intended use. Card holders conforming to this drawing are intended for use when performance specifications do not exist and qualified military devices that will perform the required function are not available for OEM application. 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery of one copy of the conformance inspection data or certificate of compliance that parts have passed conformance inspection with each shipment of parts by the manufacturer. c. Requirements for packaging and packing. DEFENSE SUPPLY CENTER, COLUMBUS SIZE CODE IDENT NO. DWG NO. COLUMBUS, OHIO A 14933 88052 REV B PAGE 11 6.3 Supersession data. Previous revisions of this document specified a nine digit PIN and allowed only cadmium plating as a finish for all card holders. Newer versions use either a ten digit PIN, with the extra digit designating the desired finish (either cadmium, ebanol or nickel). Superseded DSCC drawing PIN in accordance with DD 88052 dated 23 October 1988 Superseding DSCC drawing PIN 88052-001 88052-001C 6.4 Patents. Card holders covered by this drawing may be covered by patent 3,970,198. The Government does not possess a license under this patent for the benefit of manufacturers of the item, either for the Government or for the use in equipment to be delivered to the Government. 6.5 Users of record. Coordination of this document for future revisions are coordinated only with the suggested sources of supply and the users of record of this document. Requests to be added as a recorded user of this drawing should be in writing to: Defense Supply Center, Columbus, ATTN: DSCC/VAC, Post Office Box 3990, Columbus, OH 43216-5000 or by electronic mail at "5998.Documents@dscc.dla.mil" or by facsimile (614) 692-6939 or DSN 850-6939. 6.6 Suggested sources of supply. Suggested sources of supply are listed herein. Additional sources will be added as they become available. For assistance in the use of this drawing, contact Defense Supply Center, Columbus, ATTN: DSCC-VAC, Post Office Box 3990, Columbus, OH 43216-5000 or by electronic mail "5998.Documents@dscc.dla.mil" or by facsimile (614) 692-6939 or DSN 850-6939. DSCC drawing PIN 84168 -001 -002 -003 -004 -005 -006 -007 -008 -009 -010 -011 -012 -013 -014 -015 -016 Vendor similar designation or type number (1) DSCC drawing PIN 84168 127B-2-6-3-L 127S-2-6-3-L 127B-4-6-3-L 127S-4-6-3-L 127B-2-6-3-R 127S-2-6-3-R 127B-4-6-3-R 127S-4-6-3-R 127B-2-7-3-L 127S-2-7-3-L 127B-4-7-3-L 127S-4-7-3-L 127B-2-7-3-R 127S-2-7-3-R 127B-4-7-3-R 127S-4-7-3-R -033 -034 -035 -036 -037 -038 -039 -040 -041 -042 -043 -044 -045 -046 -047 -048 Vendor similar designation or type number (1) 127B-2-10-3-L 127S-2-10-3-L 127B-4-10-3-L 127S-4-10-3-L 127B-2-10-3-R 127S-2-10-3-R 127B-4-10-3-R 127S-4-10-3-R 127B-2-11-3-L 127S-2-11-3-L 127B-4-11-3-L 127S-4-11-3-L 127B-2-11-3-R 127S-2-11-3-R 127B-4-11-3-R 127S-4-11-3-R Vendor CAGE Vendor name, address and contact information 18915 APW Electronic Solutions 14100 Danielson Street Poway, CA 92064-6898 Tel: (858) 679-4550 Toll Free: (800) 854-7086 Fax: (858) 679-4555 URL: www.apw.com Electronic-mail: sales.electronicsolutions@ apw.com See note at end of table. DEFENSE SUPPLY CENTER, COLUMBUS SIZE CODE IDENT NO. DWG NO. COLUMBUS, OHIO A 14933 88052 REV B PAGE 12 DSCC drawing PIN 84168 Vendor similar designation or type number (1) DSCC drawing PIN 84168 Vendor similar designation or type number (1) -017 -018 -019 -020 -021 -022 -023 -024 -025 -026 -027 -028 -029 -030 -031 -032 127B-2-8-3-L 127S-2-8-3-L 127B-4-8-3-L 127S-4-8-3-L 127B-2-8-3-R 127S-2-8-3-R 127B-4-8-3-R 127S-4-8-3-R 127B-2-9-3-L 127S-2-9-3-L 127B-4-9-3-L 127S-4-9-3-L 127B-2-9-3-R 127S-2-9-3-R 127B-4-9-3-R 127S-4-9-3-R -049 -050 -051 -052 -053 -054 -055 -056 -057 -058 -059 -060 -061 -062 -063 -064 127B-2-12-3-L 127S-2-12-3-L 127B-4-12-3-L 127S-4-12-3-L 127B-2-12-3-R 127S-2-12-3-R 127B-4-12-3-R 127S-4-12-3-R 127B-2-13-3-L 127S-2-13-3-L 127B-4-13-3-L 127S-4-13-3-L 127B-2-13-3-R 127S-2-13-3-R 127B-4-13-3-R 127S-4-13-3-R -065 -066 -067 -068 -069 -070 -071 -072 -073 -074 -075 -076 -077 -078 -079 -080 127B-2-14-3-L 127S-2-14-3-L 127B-3-14-3-L 127S-3-14-3-L 127B-2-14-3-R 127S-2-14-3-R 127B-3-14-3-R 127S-3-14-3-R 127B-2-15-3-L 127S-2-15-3-L 127B-4-15-3-L 127S-4-15-3-L 127B-2-15-3-R 127S-2-15-3-R 127B-4-15-3-R 127S-4-15-3-R -097 -098 -099 -100 -101 -102 -103 -104 -105 -106 -107 -108 -109 -110 -111 -112 127B-2-18-3-L 127S-2-18-3-L 127B-4-18-3-L 127S-4-18-3-L 127B-2-18-3-R 127S-2-18-3-R 127B-4-18-3-R 127S-4-18-3-R 127B-2-19-3-L 127S-2-19-3-L 127B-4-19-3-L 127S-4-19-3-L 127B-2-19-3-R 127S-2-19-3-R 127S-4-19-3-R 127B-4-19-3-R Vendor CAGE Vendor name, address and contact information 18915 APW Electronic Solutions 14100 Danielson Street Poway, CA 92064-6898 Tel: (858) 679-4550 Toll Free: (800) 854-7086 Fax: (858) 679-4555 URL: www.apw.com Electronic-mail: sales.electronicsolutions@ apw.com See note at end of table. DEFENSE SUPPLY CENTER, COLUMBUS SIZE CODE IDENT NO. DWG NO. COLUMBUS, OHIO A 14933 88052 REV B PAGE 13 DSCC drawing PIN 84168 Vendor similar designation or type number (1) DSCC drawing PIN 84168 Vendor similar Designation or type number (1) -081 -082 -083 -084 -085 -086 -087 -088 -089 -090 -091 -092 -093 -094 -095 -096 127B-2-16-3-L 127S-2-16-3-L 127B-4-16-3-L 127S-4-16-3-L 127B-2-16-3-R 127S-2-16-3-R 127B-4-16-3-R 127S-4-16-3-R 127B-2-17-3-L 127S-2-17-3-L 127B-4-17-3-L 127S-4-17-3-L 127B-2-17-3-R 127S-2-17-3-R 127B-4-17-3-R 127S-4-17-3-R -113 -114 -115 -116 -117 -118 -119 -120 -121 -122 -123 -124 -125 -126 -127 -128 127B-2-20-3-L 127S-2-20-3-L 127B-4-20-3-L 127S-4-20-3-L 127B-2-20-3-R 127S-2-20-3-R 127B-4-20-3-R 127S-4-20-3-R 127B-2-21-3-L 127S-2-21-3-L 127B-4-21-3-L 127S-4-21-3-L 127B-2-21-3-R 127S-2-21-3-R 127B-4-21-3-R 127S-4-21-3-R -129 -130 -131 -132 -133 -134 -135 -136 -137 -138 -139 -140 -141 -142 -143 -144 127B-2-22-3-L 127S-2-22-3-L 127B-4-22-3-L 127S-4-22-3-L 127B-2-22-3-R 127S-2-22-3-R 127B-4-22-3-R 127S-4-22-3-R 127B-2-23-3-L 127S-2-23-3-L 127B-4-23-3-L 127S-4-23-3-L 127B-2-23-3-R 127S-2-23-3-R 127B-4-23-3-R 127S-4-23-3-R -145 -146 -147 -148 -149 -150 -151 -152 127B-2-24-3-L 127S-2-24-3-L 127B-4-24-3-L 127S-4-24-3-L 127B-2-24-3-R 127S-2-24-3-R 127B-4-24-3-R 127S-4-24-3-R Vendor CAGE Vendor name, address and contact information 18915 APW Electronic Solutions 14100 Danielson Street Poway, CA 92064-6898 Tel: (858) 679-4550 Toll Free: (800) 854-7086 Fax: (858) 679-4555 URL: www.apw.com Electronic-mail: sales.electronicsolutions@ apw.com (1) CAUTION: Do not use this number for item acquisition. Items acquired to this number may not satisfy the performance requirements of this drawing. DEFENSE SUPPLY CENTER, COLUMBUS SIZE CODE IDENT NO. DWG NO. COLUMBUS, OHIO A 14933 88052 REV B PAGE 14