ACS108 Overvoltage protected AC switch (ACSTM) Datasheet - production data Description COM G COM OUT COM OUT G TO-92 ACS108-6SA ACS108-8SA SOT-223 ACS108-6SN ACS108-8SN The ACS108 belongs to the AC switch range (built with A. S. D.(R) technology). This high performance switch can control a load of up to 0.8 A. The ACS108 switch includes an overvoltage crowbar structure to absorb the inductive turn-off energy, and a gate level shifter driver to separate the digital controller from the main switch. It is triggered with a negative gate current flowing out of the gate pin. Figure 1. Functional diagram Features OUT Enables equipment to meet IEC 61000-4-5 surge with overvoltage crowbar technology High noise immunity against static dV/dt and IEC 61000-4-4 burst G Needs no external protection snubber or varistor Reduces component count by up to 80% and Interfaces directly with the micro-controller COM OUT G Common package tab connection supports connection of several alternating current switches on the same cooling pad VCL gives headroom before clamping then crowbar action Applications COM Common drive reference to connect to the mains Output to connect to the load. Gate input to connect to the controller through gate resistor Table 1. Device summary Symbol Value Unit IT(RMS) 0.8 A VDRM, VRRM 600 and 800 V IGT 10 mA Alternating current on/off static switching in appliances and industrial control systems Driving low power high inductive or resistive loads like: - relay, valve, solenoid, dispenser, - pump, fan, low power motor, door lock - lamp (R): A.S.D. is a registered trademark of STMicroelectronics TM: ACS is a trademark of STMicroelectronics October 2013 This is information on a product in full production. DocID6518 Rev 5 1/13 www.st.com Characteristics 1 ACS108 Characteristics Table 2. Absolute maximum ratings (Tamb = 25 C, unless otherwise specified) Symbol Parameter TO-92 IT(RMS) ITSM I2t Tamb = 64 C Value Unit 0.45 A 0.8 A Tlead = 76 C On-state rms current (full sine wave) Non repetitive surge peak on-state current (full cycle sine wave, Tj initial = 25 C) SOT-223 S = 5 cm2 Tamb = 76 C F = 60 Hz t = 16.7 ms F = 50 Hz t = 20 ms 13 tp = 10 ms 1.1 A2s Tj = 125 C 100 A/s 2 kV Tj = 125 C 1 A Ttab = 104 C 13.7 A It Value for fusing dI/dt Critical rate of rise of on-state current IG = 2xIGT, tr 100 ns VPP Non repetitive mains peak mains voltage(1) IGM Peak gate current VGM Peak positive gate voltage Tj = 125 C 10 V Average gate power dissipation Tj = 125 C 0.1 W -40 to +150 -30 to +125 C PG(AV) Tstg Tj F = 120 Hz tp = 20 s Storage junction temperature range Operating junction temperature range 1. According to test described by IEC 61000-4-5 standard and Figure 18 Table 3. Electrical characteristics (Tj = 25 C, unless otherwise specified) Symbol IGT(1) VGT VGD Test conditions Quadrant VOUT = 12 V, RL = 33 VOUT = VDRM, RL = 3.3 kTj = 125 C Unit II - III Max. 10 mA II - III Max. 1 V II - III Min. 0.15 V IH IOUT = 100 mA Max. 10 mA IL IG = 1.2 x IGT Max. 25 mA VOUT = 402 V, gate open, Tj = 125 C Min. 2000 V/s VOUT = 536 V, gate open, Tj = 125 C Min. 400 V/s Without snubber (15 V/s), Tj = 125 C, turn-off time 20 ms Min. 2 A/ms ICL = 0.1 mA, tp = 1 ms, ACS108-6 Min. 650 V ICL = 0.1 mA, tp = 1 ms, ACS108-8 Min. 850 V dV/dt (dI/dt)c VCL 1. Minimum IGT is guaranteed at 10% of IGT max 2/13 Value DocID6518 Rev 5 ACS108 Characteristics Table 4. Static electrical characteristics Symbol VTM (1) Parameter and test conditions Value Unit ITM = 1.1 A, tp = 500 s Tj = 25 C Max. 1.3 V Vt0 (1) Threshold voltage Tj = 125 C Max. 0.85 V RD (1) Dynamic resistance Tj = 125 C Max. 300 m 2 A 0.2 mA IDRM IRRM Tj = 25 C VOUT = VDRM = VRRM Max. Tj = 125 C 1. For both polarities of OUT referenced to COM Table 5. Thermal resistance Symbol Parameter Value Rth (j-l) Junction to lead (AC) TO-92 Max. 60 Rth (j-t) Junction to tab (AC) SOT-223 Max. 25 TO-92 Max. 150 SOT-223 Max. 60 Rth (j-a) C/W Junction to ambient S = 5 cm Figure 2. Maximum power dissipation versus on-state rms current 0.9 Unit Figure 3. On-state rms current versus case temperature (SOT223) IT(RMS) (A) P (W) 0.9 = 180 0.8 a =180 0.8 SOT-223 0.7 0.7 0.6 0.6 0.5 0.5 0.4 0.4 0.3 0.3 0.2 0.2 180 0.1 0.1 IT(RMS) (A) TC C 0.0 0.0 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0 DocID6518 Rev 5 25 50 75 100 125 3/13 13 Characteristics ACS108 Figure 4. On-state rms current versus ambient temperature (free air convection) IT(RMS) (A) Figure 5. Relative variation of thermal impedance junction to ambient versus pulse duration 1.00 0.9 K=[Zth(j-a) /Rth(j-a) ] Zth(j-a) a =180 0.8 SOT-223 0.7 TO-92 0.6 0.5 0.10 0.4 TO-92 0.3 SOT-223 0.2 Single layer Printed circuit board FR4 0.1 Ta C Natural convection 0.0 0 25 50 75 SOT-223 Copper surface area = 5cm tP (s) 100 125 Figure 6. Relative variation of holding and latching current versus junction temperature IH, IL [T j] / IH, IL [T j=25 C] 0.01 1.0E-03 IL 1.0E+00 1.0E+01 1.0E+02 1.0E+03 IGT, VGT [Tj] / IGT, VGT, [Tj =25 C] IGT Q2 3.0 2.5 1.0E-01 Figure 7. Relative variation of IGT and VGT versus junction temperature 3.5 3.0 1.0E-02 IGT Q3 2.5 2.0 2.0 1.5 IH 1.5 1.0 1.0 0.5 VGT Q2-Q3 0.5 Tj(C) Tj(C) 0.0 0.0 -50 -25 0 25 50 75 100 125 Figure 8. Surge peak on-state current versus number of cycles -25 0 25 50 75 100 125 Figure 9. Non repetitive surge peak on-state current for a sinusoidal pulse, and corresponding value of It ITSM (A) 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 ITSM(A), It (As) 1.E+03 Sinusoidal pulse, tp < 10 ms Tj initial = 25 C t=20ms ITSM One cycle 1.E+02 Non repetitive Tj initial=25 C SOT-223 Repetitive Ttab = 104 C 1.E+01 1.E+00 TO-92 Repetitive Tlead = 76 C It tp(ms) Number of cycles 1.E-01 1 4/13 -50 10 100 1000 0.01 DocID6518 Rev 5 0.10 1.00 10.00 ACS108 Characteristics Figure 10. On-state characteristics (maximum values) 100.00 Figure 11. Relative variation of critical rate of decrease of main current versus junction temperature ITM(A) (dI/dt)c [Tj] / (dI/dt)c [Tj=125 C] 2.5 2.0 10.00 1.5 1.0 1.00 Tj=125 C Tj max.: Tj=25 C 0.5 Vto = 0.85 V VTM(V) Tj (C) Rd = 300 m 0.0 0.10 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 Figure 12. Relative variation of static dV/dt immunity versus junction temperature(1) 5 25 4.5 dV/dt [T j] / dV/dt [T j=125C] 35 45 55 65 75 85 95 105 115 125 Figure 13. Relative variation of leakage current versus junction temperature IDRM /IRRM [Tj;V DRM/ VRRM ]/IDRM /IRRM [Tj=125C;800 V] 1.0E+00 VD =VR=536V 4 1.0E-01 VDRM=VRRM=800 V 3 VDRM=VRRM=600 V 2 1.0E-02 1 Tj(C) Tj (C) 1.0E-03 0 25 50 75 100 125 25 50 75 100 125 1. VD = VR = 402 V: Typical values above 5 kV/s. Beyond equipment capability Figure 14. Relative variation of critical rate of decrease of main current (di/dt)c versus (dV/dt)c 5.0 Figure 15. Thermal resistance junction to ambient versus copper surface under tab (SOT-223) (dI/dt)c [ (dV/dt) c ] / Specified (dI/dt) c 140 Tj =125 C Rth(j-a) (C/W) Printed circuit board FR4 copper thickness = 35 m 4.5 SOT-223 120 4.0 100 3.5 3.0 80 2.5 2.0 60 1.5 40 1.0 20 0.5 SCU(cm) (dV/dt)c (V/s) 0 0.0 0.1 1.0 10.0 100.0 0.0 DocID6518 Rev 5 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5/13 13 Alternating current mains switch - basic application 2 ACS108 Alternating current mains switch - basic application The ACS108 switch is triggered by a negative gate current flowing from the gate pin G. The switch can be driven directly by the digital controller through a resistor as shown in Figure 16. Thanks to its overvoltage protection and turn-off commutation performance, the ACS108 switch can drive a small power high inductive load with neither varistor nor additional turn-off snubber. Figure 16. Typical application schematic Valve AC Mains ACS108 Power supply Vss MCU Vdd Rg VT 220 IT 2.1 Protection against overvoltage: the best choice is ACS In comparison with standard Triacs the ACS108 is over-voltage self-protected, as specified by the new parameter VCL. This feature is useful in two operating conditions: in case of turnoff of very inductive load, and in case of surge voltage that can occur on the electrical network. 2.1.1 High inductive load switch-off: turn-off overvoltage clamping With high inductive and low rms current loads the rate of decrease of the current is very low. An overvoltage can occur when the gate current is removed and the OUT current is lower than IH. As shown in Figure 17, at the end of the last conduction half-cycle, the load current decreases . The load current reaches the holding current level IH , and the ACS turns off . The water valve, as an inductive load (up to 15 H), reacts as a current generator and an overvoltage is created, which is clamped by the ACS . The current flows through the ACS avalanche and decreases linearly to zero. During this time, the voltage across the switch is limited to the clamping voltage VCL. The energy stored in the inductance of the load is dissipated in the clamping section that is designed for this purpose. When the energy has been dissipated, the ACS voltage falls back to the mains voltage value (230 V rms, 50 Hz) . 6/13 DocID6518 Rev 5 ACS108 Alternating current mains switch - basic application Figure 17. Switching off of a high inductive load - typical clamping capability of ACS108 (Tamb = 25 C) 4 VCL IT 1 3 VT 2 IH (200 V/div) 3 4 IT VT 5 (5 mA/div) VCL 1 2 100 s/div 2.1.2 IH 5 Alternating current mains transient voltage ruggedness The ACS108 switch is able to withstand safely the AC mains transients either by clamping the low energy spikes or by breaking-over when subjected to high energy shocks, even with high turn-on current rises. The test circuit shown in Figure 18 is representative of the final ACS108 application, and is also used to test the AC switch according to the IEC 61000-4-5 standard conditions. Thanks to the load limiting the current, the ACS108 switch withstands the voltage spikes up to 2 kV above the peak mains voltage. The protection is based on an overvoltage crowbar technology. Actually, the ACS108 breaks over safely as shown in Figure 19. The ACS108 recovers its blocking voltage capability after the surge (switch off back at the next zero crossing of the current). Such non-repetitive tests can be done 10 times on each AC mains voltage polarity. Figure 18. Overvoltage ruggedness test circuit for resistive and inductive loads, Tamb = 25 C (conditions equivalent to IEC 61000-4-5 standard) +2 kV surge generator CC Load 150 5 H ACS108 OUT Mains voltage 230 V rms 50 Hz G VT COM IT DocID6518 Rev 5 220 7/13 13 Alternating current mains switch - basic application ACS108 Figure 19. Typical current and voltage waveforms across the ACS108 (+2 kV surge, IEC 61000-4-5 standard) VT (200 V/div) IT max = 17.2 A dIT/dt = 1.8 A/s IT (4 A/div) 500 ns/div 8/13 DocID6518 Rev 5 ACS108 3 Package information Package information Epoxy meets UL94, V0 Lead-free packages In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK(R) packages, depending on their level of environmental compliance. ECOPACK(R) specifications, grade definitions and product status are available at: www.st.com. ECOPACK(R) is an ST trademark. Figure 20. TO-92 dimension definitions A a B C F D E Table 6. TO-92 dimension values Dimensions Ref Millimeters Min. A Typ. Inches Max. Min. 1.35 B Typ. 0.053 4.70 C Max. 0.185 2.54 0.100 D 4.40 0.173 E 12.70 0.500 F 3.70 0.146 a 0.50 0.019 DocID6518 Rev 5 9/13 13 Package information ACS108 Figure 21. SOT-223 dimension definitions V A A1 c B e1 D B1 4 H E 1 2 3 e Table 7. SOT-223 dimension values Dimensions Ref. Millimeters Min. Inches Typ. Max. 0.02 0.10 A Min. Typ. Max. 0.001 0.004 1.80 A1 0.071 B 0.60 0.70 0.85 0.024 0.027 0.033 B1 2.90 3.00 3.15 0.114 0.118 0.124 c 0.24 0.26 0.35 0.009 0.010 0.014 D(1) 6.30 6.50 6.70 0.248 0.256 0.264 e 2.3 0.090 e1 4.6 0.181 (1) 3.30 3.50 3.70 0.130 0.138 0.146 H 6.70 7.00 7.30 0.264 0.276 0.287 E V 10 max 1. Do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.15mm (0.006inches) Figure 22. SOT-223 footprint (dimensions in mm) 3.25 1.32 5.16 7.80 1.32 2.30 10/13 DocID6518 Rev 5 0.95 ACS108 4 Ordering information Ordering information Figure 23. Ordering information scheme ACS 1 08 - 6 S A -TR AC switch series Number of switches Current 08 = 0.8 A rms Voltage 6 = 600 V 8 = 800 V Sensitivity S = 10 mA Package A = TO-92 N = SOT-223 Packing TR = Tape and reel 7" (SOT-223, 1000 pieces) 13" (TO-92, 2000 pieces) AP = Ammopack (TO-92, 2000 pieces) Blank = bulk (TO-92, 2500 pieces) Table 8. Ordering information Order code Marking ACS108-6SA ACS108-6SA-TR ACS1 086SA ACS108-6SA-AP ACS108-6SN-TR ACS 108 6SN ACS108-8SA ACS108-8SA-TR ACS1 088SA ACS108-8SA-AP ACS108-8SN-TR ACS 108 8SN Package Weight Base Qty Delivery mode TO-92 0.2 g 2500 Bulk TO-92 0.2 g 2000 Tape and reel TO-92 0.2 g 2000 Ammopack SOT-223 0.11 g 1000 Tape and reel TO-92 0.2 g 2500 Bulk TO-92 0.2 g 2000 Tape and reel TO-92 0.2 g 2000 Ammopack SOT-223 0.11 g 1000 Tape and reel DocID6518 Rev 5 11/13 13 Revision history 5 ACS108 Revision history Table 9. Document revision history 12/13 Date Revision Changes Apr_2004 1 Initial release. This datasheet covers order codes previously described in the datasheet for ACS108-6S, Doc ID 11962, Rev 3 December 2010. 21-Jun-2005 2 Marking information updated from ACSxxxx to ACS1xxx. 11-Jul-2012 3 Removed 500 V devices and added 600 V and 800 V devices. 27-Sep-2013 4 Corrected typographical error in Figure 4. 31-Oct-2013 5 Corrected character formatting issues in Section 2.1.1. DocID6518 Rev 5 ACS108 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ("ST") reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST's terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST'S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. ST PRODUCTS ARE NOT DESIGNED OR AUTHORIZED FOR USE IN: (A) SAFETY CRITICAL APPLICATIONS SUCH AS LIFE SUPPORTING, ACTIVE IMPLANTED DEVICES OR SYSTEMS WITH PRODUCT FUNCTIONAL SAFETY REQUIREMENTS; (B) AERONAUTIC APPLICATIONS; (C) AUTOMOTIVE APPLICATIONS OR ENVIRONMENTS, AND/OR (D) AEROSPACE APPLICATIONS OR ENVIRONMENTS. WHERE ST PRODUCTS ARE NOT DESIGNED FOR SUCH USE, THE PURCHASER SHALL USE PRODUCTS AT PURCHASER'S SOLE RISK, EVEN IF ST HAS BEEN INFORMED IN WRITING OF SUCH USAGE, UNLESS A PRODUCT IS EXPRESSLY DESIGNATED BY ST AS BEING INTENDED FOR "AUTOMOTIVE, AUTOMOTIVE SAFETY OR MEDICAL" INDUSTRY DOMAINS ACCORDING TO ST PRODUCT DESIGN SPECIFICATIONS. PRODUCTS FORMALLY ESCC, QML OR JAN QUALIFIED ARE DEEMED SUITABLE FOR USE IN AEROSPACE BY THE CORRESPONDING GOVERNMENTAL AGENCY. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. (c) 2013 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com DocID6518 Rev 5 13/13 13 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: STMicroelectronics: ACS108-6SA ACS108-6SA-AP ACS108-6SA-TR ACS108-6SN-TR ACS108-8SA-TR ACS108-8SN-TR ACS1088SA ACS108-8SA-AP