EGP10A THRU EGP10G
GLASS PASSIVATED FAST EFFICIENT RECTIFIER
Reverse Voltage - 50 to 400 Volts Forward Current - 1.0 Ampere
FEATURES
♦ Plastic package has Underwriters Laboratories
Flammability Classification 94V-0
♦ Glass passivated cavity-free junction
♦ Superfast recovery time for high efficiency
♦ Low forward voltage, high current capability
♦ Low leakage current
♦ High surge current capability
♦ High temperature metallurgically
bonded construction
♦ High temperature soldering guaranteed:
300°C/10 seconds, 0.375" (9.5mm) lead length,
5 lbs. (2.3kg) tension
MECHANICAL DATA
Case: JEDEC DO-204AL molded plastic over glass body
Terminals: Plated axial leads, solderable per MIL-STD-750,
Method 2026
Polarity: Color band denotes cathode end
Mounting Position: Any
Weight: 0.012 ounce, 0.3 gram
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25°C ambient temperature unless otherwise specified.
EGP EGP EGP EGP EGP EGP
SYMBOLS 10A 10B 10C 10D 10F 10G UNITS
Maximum repetitive peak reverse voltage VRRM 50 100 150 200 300 400 Volts
Maximum RMS voltage VRMS 35 70 105 140 210 280 Volts
Maximum DC blocking voltage VDC 50 100 150 200 300 400 Volts
Maximum average forward rectified current
0.375" (9.5mm) lead length at TA=55°C I(AV) 1.0 Amp
Peak forward surge current
8.3ms single half sine-wave superimposed
on rated load IFSM 30.0 Amps
Maximum instantaneous forward voltage at 1.0A VF0.95 1.25 Volts
Maximum DC reverse current TA=25°C 5.0
at rated DC blocking voltage TA=125°C IR100 µA
Maximum reverse recover y time (NOTE 1) trr 50.0 ns
Typical junction capacitance (NOTE 2) CJ22.0 15.0 pF
Typical ther mal resistance (NOTE 3 )R
ΘJA 50.0 °C/W
Operating junction and storage temperature range TJ, TSTG -65 to +150 °C
NOTES:
(1) Reverse recovery test conditions: IF=0.5A, IR=1.0A, Irr=0.25A
(2) Measured at 1.0 MHZand applied reverse voltage of 4.0 Volts
(3) Ther mal resistance from junction to ambient at 0.375" (9.5mm) lead length, P.C.B. mounted
4/98
®
Dimensions in inches and (millimeters)
*
Glass Encapsulation technique is covered by
Patent No. 3,996,602, brazed-lead assembly to Patent No. 3,930,306
DO-204AL
0.107 (2.7)
0.080 (2.0)
0.034 (0.86)
0.028 (0.71)
DIA.
1.0 (25.4)
MIN.
1.0 (25.4)
MIN.
0.205 (5.2)
0.160 (4.1)
DIA.
PATENTED*
1750100
0
0.5
1.0
25 50 75 125 150 110
5.0
10
20
100
0
15
25
30
0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8
0.01
0.1
1
10
50
0.01 0.1 110 100
0.1
1
10
100
0.1 110 100
0
10
20
30
40
50
60
70
20 80
0.1
10
100
0 40 60 100
1,000
0
1
RATINGS AND CHARACTERISTICS CURVES EGP10A THRU EGP10G
FIG. 1 - MAXIMUM FORWARD CURRENT
DERATING CURVE
AMBIENT TEMPERATURE, °C
AVERAGE FORWARD RECTIFIED CURRENT,
AMPERES
RESISTIVE OR
INDUCTIVE LOAD
0.375” (9.5mm)
LEAD LENGTH
FIG. 4 - TYPICAL REVERSE CHARACTERISTICS
INSTANTANEOUS REVERSE LEAKAGE CURRENT,
MICROAMPERES
PERCENT OF RATED PEAK REVERSE
VOLTAGE, %
TJ=25°C
TJ=150°C
PULSE WIDTH=300µs
1% DUTY CYCLE
FIG. 3 -TYPICAL INSTANTANEOUS FORWARD
CHARACTERISTICS
INSTANTANEOUS FORWARD VOLTAGE,
VOLTS
INSTANTANEOUS FORWARD FORWARD CURRENT,
AMPERES
TJ=TJmax.
8.3ms SINGLE HALF SINE WAVE
(JEDEC Method)
FIG. 2 - MAXIMUM NON-REPETITIVE PEAK
FORWARD SURGE CURRENT
PEAK FORWARD SURGE CURRENT,
AMPERES
FIG. 6 - TYPICAL TRANSIENT THERMAL IMPEDANCE
t, PULSE DURATION, sec.
TRANSIENT THERMAL IMPEDANCE, °CW
TJ=25°C
f=1.0 MHZ
Vsig=50mVp-p
TJ=150°C
TJ=100°C
TJ=25°C
EGP10A - EGP10D
EGP10F & EGP10G
NUMBER OF CYCLES AT 60 HZ
FIG. 5 - TYPICAL JUNCTION CAPACITANCE
JUNCTION CAPACITANCE, pF
REVERSE V OLTAGE, V OLTS
EGP10A - EGP10D
EGP10F & EGP10G
