Blackfin(R) A-V EZ-Extender(R) Manual Revision 2.1, July 2012 Part Number 82-000870-01 Analog Devices, Inc. One Technology Way Norwood, Mass. 02062-9106 a Copyright Information (c) 2012 Analog Devices, Inc., ALL RIGHTS RESERVED. This document may not be reproduced in any form without prior, express written consent from Analog Devices, Inc. Printed in the USA. Disclaimer Analog Devices, Inc. reserves the right to change this product without prior notice. Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use; nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under the patent rights of Analog Devices, Inc. Trademark and Service Mark Notice The Analog Devices logo, Blackfin, CrossCore, EngineerZone, EZ-Extender, EZ-KIT Lite, and VisualDSP++ are registered trademarks of Analog Devices, Inc. All other brand and product names are trademarks or service marks of their respective owners. Regulatory Compliance The Blackfin A-V EZ-Extender is designed to be used solely in a laboratory environment. The board is not intended for use as a consumer end product or as a portion of a consumer end product. The board is an open system design which does not include a shielded enclosure and therefore may cause interference to other electrical devices in close proximity. This board should not be used in or near any medical equipment or RF devices. The Blackfin A-V EZ-Extender has been certified to comply with the essential requirements of the European EMC directive 2004/108/EC and therefore carries the "CE" mark. The Blackfin A-V EZ-Extender has been appended to Analog Devices, Inc. EMC Technical File (EMC TF) referenced DSPTOOLS1, issue 2 dated June 4, 2008 and was declared CE compliant by an appointed Notified Body (No.0673) as listed below. Notified Body Statement of Compliance: Z600ANA1.023 dated December 2, 2004. Issued by: Technology International (Europe) Limited 56 Shrivenham Hundred Business Park Shrivenham, Swindon, SN6 8TY, UK The Blackfin A-V EZ-Extender contains ESD (electrostatic discharge) sensitive devices. Electrostatic charges readily accumulate on the human body and equipment and can discharge without detection. Permanent damage may occur on devices subjected to high-energy discharges. Proper ESD precautions are recommended to avoid performance degradation or loss of functionality. Store unused extender boards in the protective shipping package. CONTENTS PREFACE Product Overview .......................................................................... x Purpose of This Manual ................................................................ xi Intended Audience ....................................................................... xii Manual Contents ......................................................................... xii What's New in This Manual ........................................................ xiii Technical Support ....................................................................... xiii Supported Processors .................................................................... xiv Product Information .................................................................... xiv Analog Devices Web Site ........................................................ xiv EngineerZone .......................................................................... xv Related Documents ...................................................................... xvi A-V EZ-EXTENDER INTERFACES A-V EZ-Extender Setup ................................................................ 1-2 Analog Audio Interface .................................................................. 1-3 Analog Video Interface .................................................................. 1-4 Camera Module Interfaces ............................................................. 1-4 Blackfin A-V EZ-Extender Manual v Contents Flat Panel Display Interface ........................................................... 1-6 Example Programs ........................................................................ 1-7 A-V EZ-EXTENDER HARDWARE REFERENCE System Architecture ...................................................................... 2-2 Jumpers ........................................................................................ 2-7 Video Test Loopback Jumpers (JP1.1/2, JP1.3/4, JP1.5/6) ....... 2-8 Connector Voltage Selection Jumper (JP2) ............................... 2-8 TWI Source Selection Jumpers (JP3.3/5/7, JP3.4/6/8) ............. 2-8 PDWN Connect Jumper (JP3.9/10) ........................................ 2-9 Decoder HSYNC Disconnect Jumper (JP3.11/12) ................... 2-9 Decoder VSYNC Connect Jumper (JP3.13/14) ........................ 2-9 Encoder HREF Connect Jumper (JP3.15/16) ........................ 2-10 Encoder VSYNC Connect Jumper (JP3.17/18) ...................... 2-10 Decoder Output Enable Jumper (JP3.19/20) ......................... 2-10 SNAPSHOT_FODD Disconnect Jumper (JP3.21/22) ........... 2-10 PPI Clock Setup Jumpers (JP4.1/2, JP4.3/4, JP4.5/6, JP4.7/8) ................................... 2-11 PPI0 D8-15 Enable Jumper (JP5.1/2) ................................... 2-11 VID_OUT Data Bus Control Jumpers (JP5.3/4, JP5.5/6) ...... 2-12 PPI0_SYNC1 Direction Setup Jumper (JP6.1/3/5) ................ 2-12 PPI0_SYNC2 Direction Setup Jumper (JP6.2/4/6) ................ 2-13 I2S Enable Jumper (JP7.1/2) ................................................. 2-13 SPORT Data Connect Jumpers (JP7.3/4, JP7.5/6) ................ 2-13 vi Blackfin A-V EZ-Extender Manual Contents VID_OUT Bus SYNC Source Select Jumpers (JP8.1/3/5, JP8.2/4/6) ........................................................ 2-14 VID_OUT Bus SYNC Enable Jumper (JP8.7/8) .................... 2-14 AV_RESET Source Jumper (JP9.1/3/5) .................................. 2-14 PPI0_D Direction Setup Jumper (JP9.2/4/6) ......................... 2-15 Audio Loopback Jumpers (JP10.1/2, JP10.3/4) ...................... 2-15 A-V EZ-EXTENDER BILL OF MATERIALS A-V EZ-EXTENDER SCHEMATIC INDEX Blackfin A-V EZ-Extender Manual vii Contents viii Blackfin A-V EZ-Extender Manual PREFACE Thank you for purchasing the Blackfin(R) A-V EZ-Extender(R), Analog Devices, Inc. daughter board to the EZ-KIT Lite(R) evaluation system for the ADSP-BF533, ADSP-BF537, and ADSP-BF561 Blackfin processors. Blackfin processors are embedded processors that support a Media Instruction Set Computing (MISC) architecture. This architecture is the natural merging of RISC, media functions, and digital signal processing characteristics towards delivering signal processing performance in a microprocessor-like environment. EZ-KIT Lites and A-V EZ-Extenders are designed to be used in conjunction with the CrossCore(R) Embedded Studio (CCES) and VisualDSP++(R) software development environments. The development environment facilitates advanced application code development and debug, such as: * Create, compile, assemble, and link application programs written in C++, C, and A-V EZ-Extender assembly * Load, run, step, halt, and set breakpoints in application programs * Read and write data and program memory * Read and write core and peripheral registers * Plot memory To learn more about Analog Devices development software, go to http://www.analog.com/processors/tools. Blackfin A-V EZ-Extender Manual ix Product Overview Product Overview The Blackfin A-V EZ-Extender is a separately sold daughter board that plugs onto the expansion interface of the ADSP-BF533, ADSP-BF537, or ADSP-BF561 EZ-KIT Lite evaluation system. The extender board aids the design and prototyping phases of the ADSP-BF533, ADSP-BF537, or ADSP-BF561 processor targeted applications. The board extends the evaluation system capabilities by providing a connection to a video decoder; video encoder; multiple camera evaluation boards; flat panel display; and 3-stereo input channel, 2-stereo output channel audio codec. Please visit www.analog.com/EX1-AV for additional information, including CCES support. The board features: * Analog audio interface * AD1836A Analog Devices 96 kHz audio codec * Five 3.5 mm audio jacks, stacked in one connector * Analog video interface * ADV7183B video decoder with three input RCA phono jacks * ADV7179 video encoder with three output RCA phono jacks * OmniVision camera module interface * Connection to OmniVision camera evaluation modules; for example, OV6630AA (this part is no longer available) * 32-pin, right-angle, 0.1 in. spacing, female socket x Blackfin A-V EZ-Extender Manual Preface * Micron camera module interface * Connection to Micron camera evaluation modules; for example, MT9V022 (this part is no longer available) * 26-pin, right-angle, 0.1 in. spacing, female socket * Kodak camera module interface * Connection to Kodak camera evaluation modules; for example, KAC-9628 (this part is no longer available) * 28-pin, right- angle, 0.1 in. spacing, female socket * Flat panel display interface (FPDI) * Connection to flat panel displays; for example, NL6448BC20-08E * DF9B-31S-1V connector Before using any of the interfaces, follow the procedure in "A-V EZ-Extender Interfaces" on page 1-1. Example programs are available to demonstrate the Blackfin A-V EZ-Extender capabilities. Purpose of This Manual The Blackfin A-V EZ-Extender Manual provides instructions for installing the product hardware (board). The text describes operation and configuration of the board components and provides guidelines for running your own code on the A-V EZ-Extender. Finally, a schematic and a bill of materials are provided for reference. Blackfin A-V EZ-Extender Manual xi Intended Audience Intended Audience The primary audience for this manual is a programmer who is familiar with Analog Devices processors. This manual assumes that the audience has a working knowledge of the appropriate processor architecture and instruction set. Programmers who are unfamiliar with Analog Devices processors can use this manual but should supplement it with other texts that describe your target architecture. For the locations of these documents, see "Related Documents". Programmers who are unfamiliar with CCES or VisualDSP++ should refer to the online help and user's manuals. Manual Contents The manual consists of: * Chapter 1, "A-V EZ-Extender Interfaces" on page 1-1 Provides basic board information. * Chapter 2, "A-V EZ-Extender Hardware Reference" on page 2-1 Provides information on the hardware aspects of the board. * Appendix A, "A-V EZ-Extender Bill of Materials" on page A-1 Provides a list of components used to manufacture the board. * Appendix B, "A-V EZ-Extender Schematic" on page B-1 Provides the resources to allow EZ-KIT Lite board-level debugging or to use as a reference design. Appendix B is part of the online help. xii Blackfin A-V EZ-Extender Manual Preface What's New in This Manual This is revision 2.1 of the Blackfin A-V EZ-Extender Manual. The manual has been updated to include CCES information. In addition, modifications and corrections based on errata reports against the previous manual revision have been made. For the latest version of this manual, please refer to the Analog Devices Web site. Technical Support You can reach Analog Devices processors and DSP technical support in the following ways: * Post your questions in the processors and DSP support community at EngineerZone(R): http://ez.analog.com/community/dsp * Submit your questions to technical support directly at: http://www.analog.com/support * E-mail your questions about processors, DSPs, and tools development software from CrossCore Embedded Studio or VisualDSP++: Choose Help > Email Support. This creates an e-mail to processor.tools.support@analog.com and automatically attaches your CrossCore Embedded Studio or VisualDSP++ version information and license.dat file. * E-mail your questions about processors and processor applications to: processor.support@analog.com or processor.china@analog.com (Greater China support) Blackfin A-V EZ-Extender Manual xiii Supported Processors * In the USA only, call 1-800-ANALOGD (1-800-262-5643) * Contact your Analog Devices sales office or authorized distributor. Locate one at: www.analog.com/adi-sales * Send questions by mail to: Processors and DSP Technical Support Analog Devices, Inc. Three Technology Way P.O. Box 9106 Norwood, MA 02062-9106 USA Supported Processors This extender board supports Analog Devices ADSP-BF533, ADSP-BF537, and ADSP-BF561 Blackfin embedded processors. Product Information Product information can be obtained from the Analog Devices Web site and the online help. Analog Devices Web Site The Analog Devices Web site, www.analog.com, provides information about a broad range of products--analog integrated circuits, amplifiers, converters, and digital signal processors. To access a complete technical library for each processor family, go to http://www.analog.com/processors/technical_library. The manuals selection opens a list of current manuals related to the product as well as a xiv Blackfin A-V EZ-Extender Manual Preface link to the previous revisions of the manuals. When locating your manual title, note a possible errata check mark next to the title that leads to the current correction report against the manual. Also note, MyAnalog is a free feature of the Analog Devices Web site that allows customization of a Web page to display only the latest information about products you are interested in. You can choose to receive weekly e-mail notifications containing updates to the Web pages that meet your interests, including documentation errata against all manuals. MyAnalog provides access to books, application notes, data sheets, code examples, and more. Visit MyAnalog to sign up. If you are a registered user, just log on. Your user name is your e-mail address. EngineerZone EngineerZone is a technical support forum from Analog Devices. It allows you direct access to ADI technical support engineers. You can search FAQs and technical information to get quick answers to your embedded processing and DSP design questions. Use EngineerZone to connect with other DSP developers who face similar design challenges. You can also use this open forum to share knowledge and collaborate with the ADI support team and your peers. Visit http://ez.analog.com to sign up. Blackfin A-V EZ-Extender Manual xv Related Documents Related Documents For additional information about the product, refer to the following publications. Table 1. Related Processor Publications Title Description * ADSP-BF531/ADSP-BF532/ADSP-BF533 Blackfin Embedded Processor Data Sheet * ADSP-BF534/ADSP-BF536/ADSP-BF537 Blackfin Embedded Processor Data Sheet * ADSP-BF561 Blackfin Embedded Symmetric Multiprocessor Data Sheet * ADSP-BF533 Blackfin Processor Hardware Reference * ADSP-BF537 Blackfin Processor Hardware Reference * ADSP-BF561 Blackfin Processor Hardware Reference General functional description, pinout, and timing of the processor Blackfin Processor Programming Reference Description of all allowed processor assembly instructions xvi Description of the internal processor architecture and all register functions Blackfin A-V EZ-Extender Manual 1 A-V EZ-EXTENDER INTERFACES This chapter provides a setup procedure for the Blackfin A-V EZ-Extender and EZ-KIT Lite (ADSP-BF533, ADSP-BF537, or ADSP-BF561). The chapter also describes each evaluation interface the extender supports. The information is presented in the following order. * "A-V EZ-Extender Setup" on page 1-2 * "Analog Audio Interface" on page 1-3 * "Analog Video Interface" on page 1-4 * "Camera Module Interfaces" on page 1-4 * "Flat Panel Display Interface" on page 1-6 * "Example Programs" on page 1-7 Blackfin A-V EZ-Extender Manual 1-1 A-V EZ-Extender Setup A-V EZ-Extender Setup It is very important to set up all components of the system containing the Blackfin A-V EZ-Extender, then apply power to the system. Power your system after these steps are completed: 1. Read the applicable design interface section in this chapter--the text provides an overview of the interface capabilities. 2. Read "System Architecture" on page 2-2 to understand the physical connections of the extender board. For more detailed information, refer to "A-V EZ-Extender Schematic" on page B-1. 3. Set the jumpers on the extender board. Use the block diagram in Figure 2-1 on page 2-3 in conjunction with "Jumpers" on page 2-7. 4. Set the switches and jumpers on the EZ-KIT Lite board. If not already, familiarize yourself with the documentation and schematic drawing of the EZ-KIT Lite (see "Related Documents"). Compare the expansion interface signals of the extender with the EZ-KIT Lite signals to ensure there is no contention. For example, it may be necessary to disable other devices connected to the parallel peripheral interface (PPI) of the processor, change the routing of the PPI clocks, and disable the push buttons. 5. Configure any other interfacing boards; for example, another EZ-Extender or a camera evaluation board. 1-2 Blackfin A-V EZ-Extender Manual A-V EZ-Extender Interfaces Analog Audio Interface The Blackfin A-V EZ-Extender supports audio applications with the on-board AD1836A multichannel 96 kHz audio codec. The AD1836A codec is a high-performance single-chip device that provides three stereo digital-to-analog converters (outputs) and two stereo analog-to-digital converters (inputs), using Analog Devices patented multibit sigma-delta architecture. The board includes a serial peripheral interface (SPI) port, enabling the processor to adjust volume and other parameters. For a general overview of the audio interface connections, see Figure 2-1 on page 2-3; for details, see "A-V EZ-Extender Schematic" on page B-1. of the expansion interface connects to the serial port of the AD1836A codec. The processor is capable of transferring data to the audio codec in time-division multiplexed (TDM) mode or I2S mode. In I2S mode, the codec can operate at a 96 kHz sample rate and allows two channels of output. In TDM mode, the codec can operate at a maximum of 48 kHz sample rate and allows simultaneous use of all input and output channels. To operate in I2S mode, install the JP7.1/2 jumper. For more information, see "I2S Enable Jumper (JP7.1/2)" on page 2-13. SPORT0 Internal registers of the AD1836A audio codec can be programmed via the SPI port of the processor. (For information on how to program the configuration registers, refer to the AD1836A data sheet.) The AD1836A codec reset comes from a flag pin located at PPI1_D11 of the expansion interface or from the reset signal on the EZ-KIT Lite. For information on how to configure the reset, see "AV_RESET Source Jumper (JP9.1/3/5)" on page 2-14. Before using the interface, follow the procedure in "A-V EZ-Extender Setup" on page 1-2. For more information about the codec, go to www.analog.com/AD1836A. Blackfin A-V EZ-Extender Manual 1-3 Analog Video Interface Analog Video Interface The Blackfin A-V EZ-Extender supports video input and output applications with an on-board video encoder and decoder. The ADV7179 video encoder provides up to three output channels of analog video, while the ADV7183B video decoder provides up to three input channels of analog video. Both the encoder and decoder connect to PPI0 of the expansion interface, while the encoder also can connect to PPI1 (if the processor has two PPI ports). For a general overview of the analog video interface connectors, see Figure 2-1 on page 2-3; for details, see "AV_RESET Source Jumper (JP9.1/3/5)" on page 2-14. To use ADV7179 and ADV7183B, set up all of the jumpers related to the PPI data signals, frame sync signals, and clock signal. To program the internal register of video devices, configure the 2-wire interface signals (see "TWI Source Selection Jumpers (JP3.3/5/7, JP3.4/6/8)" on page 2-8). Finally, determine the source of encoder or decoder reset, as described in "AV_RESET Source Jumper (JP9.1/3/5)" on page 2-14. Before using the interface, follow the procedure in "A-V EZ-Extender Setup" on page 1-2. For more information about ADV7179 and ADV7183B, go to www.analog.com/ADV7179 and www.analog.com/ADV7183B. Camera Module Interfaces The Blackfin A-V EZ-Extender has three right-angle connectors (J4, J6, and P4) with control signals necessary to interface with three camera evaluation modules from different manufactures. For a general overview of the camera interface connections, see Figure 2-1 on page 2-3; for details, see "A-V EZ-Extender Schematic" on page B-1. Figure 1-1 shows the orientation of the camera modules as each camera connects to the board. 1-4 Blackfin A-V EZ-Extender Manual A-V EZ-Extender Interfaces Figure 1-1. Camera Orientation J6 is a connector designated for a Micron camera sensor evaluation module. The interface has been tested with the Micron MT9V022 camera. For information about Micron camera sensors and evaluation boards, go to http://www.micron.com. is a connector designated for an OmniVision camera sensor evaluation module. The interface has been tested with the OmniVision OV6630AA camera. For information about OmniVision camera sensors and evaluation boards, go to http://www.ovt.com. J4 is a connector designated for a Kodak camera sensor evaluation module. The interface has been tested with the Kodak KAC-9628 camera. For information about Kodak camera sensors and evaluation boards, go to http://www.kodak.com. P4 To connect the Blackfin A-V EZ-Extender to a camera module, first determine the source of the PPI clock. To learn about possible clock settings, refer to "PPI Clock Setup Jumpers (JP4.1/2, JP4.3/4, JP4.5/6, Blackfin A-V EZ-Extender Manual 1-5 Flat Panel Display Interface JP4.7/8)" on page 2-11. Then set the direction of the data and frame sync signals, which depend on the camera's configuration. The data must be set as input to the PPI port; refer to "System Architecture" on page 2-2 and "Jumpers" on page 2-7 for details. Before using the camera interfaces, follow the procedure in "A-V EZ-Extender Setup" on page 1-2. Flat Panel Display Interface The flat panel display interface (FPDI) consists of a 31-pin DB9 connector linked to the PPI port and frame sync signals of the processor. For a general overview of the display interface connections, see Figure 2-1 on page 2-3; for details, see the "A-V EZ-Extender Schematic" on page B-1. A timing and functional analysis is required to determine whether a specific LCD module can connect to the Blackfin A-V EZ-Extender. An example of display that can connect to the extender is the NEC NL6448BC20-08 display. power for the backlight feature of the LCD module must be The provided by the customer (use the backlight inverter recommended by the manufacturer). In addition, it is necessary to purchase a cable to connect the Blackfin A-V EZ-Extender to the display; for example, FDC31/xxxxAFF03 from Axon Cable (www.axon-cable.com, part number FDC31/xxxxAFF03). Different length cables are available. Before using the interface, follow the procedure in "A-V EZ-Extender Setup" on page 1-2. 1-6 Blackfin A-V EZ-Extender Manual A-V EZ-Extender Interfaces Example Programs Example programs are provided with the A-V EZ-Extender EZ-KIT Lite to demonstrate various capabilities of the product. The programs are included in the product installation kit and can be found in the Examples folder of the installation. Refer to a readme file provided with each example for more information. CCES users are encouraged to use the example browser to find examples included with the EZ-KIT Lite Board Support Package. Blackfin A-V EZ-Extender Manual 1-7 Example Programs 1-8 Blackfin A-V EZ-Extender Manual 2 A-V EZ-EXTENDER HARDWARE REFERENCE This chapter describes the hardware design of the Blackfin A-V EZ-Extender. The following topics are covered. * "System Architecture" on page 2-2 Describes the extender board configuration and explains how the board components interface with the processor and EZ-KIT Lite. * "Jumpers" on page 2-7 Describes the configuration jumpers. Blackfin A-V EZ-Extender Manual 2-1 System Architecture System Architecture A block diagram of the Blackfin A-V EZ-Extender is shown in Figure 2-1. Not shown in the diagram is the analog audio interface, which is a simple connection between the serial port of the processor and AD1836A audio codec. The audio interface connects directly to SPORT0 of the expansion interface. In Figure 2-1, unidirectional buffers are show as triangle symbols, while bidirectional buffers are shown as two overlapping triangles. For both types of buffers, an output-enable signal comes out of the top and is active LOW. For bidirectional buffers, a second signal for the direction is shown. When this net is pulled HIGH, the buffer is driving in the direction of the arrow in the center; when LOW, the buffer is driving in the opposite direction. applying power to the system, follow the procedure in "A-V Before EZ-Extender Setup" on page 1-2. The video interface can be split into two main signal sets: VID_IN and VID_OUT. Both signal sets consist of a 16-bit data bus, two frame sync signals, and a data clock. VID_IN connects to the video decoder and all camera interfaces. VID_IN connects only to the PPI0 of the EZ-KIT Lite. VID_OUT connects to the video encoder and flat panel display interface. On the expansion interface, VID_OUT connects to either PPI0 or PPI1 of the EZ-KIT Lite. 2-2 Blackfin A-V EZ-Extender Manual A-V EZ-Extender Hardware Reference Figure 2-1. A-V EZ-Extender Block Diagram Blackfin A-V EZ-Extender Manual 2-3 System Architecture Table 2-1 summarizes the signals coming and going on the expansion interface connectors. Table 2-1. Signals of Expansion Interface Connectors Net/Bus Name (Direction) Blackfin A-V EZ-Extender Function Relevant Configuration Jumpers PPI0_D[0:15] Connects the processor's PPI0 data pins to the VID_IN_D[0:15] or VID_OUT_D[0:15] buses, depending on the jumper settings. This allows PPI0 to interface with all video interfaces on the board. The bus can be bidirectional, where the direction is fixed with a jumper or controlled by a flag pin. JP5.3/4, JP9.2/4/6 The clock related to the data on PPI0. This can come from an on-board oscillator, one of the video interfaces, or a socket that allows a user-supplied oscillator. JP4.1/2, JP4.3/4, JP4.5/6, JP4.7/8 The frame sync signal going to the processor's PPI0_SYNC1 pin. The signal behaves as HSYNC or HREF for the video interfaces. The signal also can be used to drive the FPDI's HS signal. The signal can be bidirectional, where the direction is fixed with a jumper or controlled by a flag pin. JP6.1/3/5, JP8.1/3/5, JP8.7/8 The frame sync signal going to the processor's PPI0_SYNC2 pin. The signal behaves as VSYNC or VREF for the video interfaces. In addition, the signal can drive the FPDI's VS signal. The signal can be bidirectional, where the direction is fixed with a jumper or controlled by a flag pin. JP6.2/4/6, JP8.2/4/6, JP8.7/8 Connects the processor's PPI1 data pins to the VID_OUT_D[0:15] bus. The VID_OUT_D[0:15] bus interfaces with the output video interfaces (FPDI and video encoder). The bus can be bidirectional but intended to be an input. Changing the direction is necessary only for test purposes and allows PPI0 to loop-back to PPI1. Note: D2, D3, and D10 of the bus have other functions (follows). JP5.3/4, JP5.5/6, (Bi) PPI0_CLK (Output) PPI0_SYNC1 (Bi) PPI0_SYNC2 (Bi) PPI1_D[0:15] (Bi) 2-4 JP3.9/10, JP3.3/5/7 JP3.4/6/8 Blackfin A-V EZ-Extender Manual A-V EZ-Extender Hardware Reference Table 2-1. Signals of Expansion Interface Connectors (Cont'd) Net/Bus Name (Direction) Blackfin A-V EZ-Extender Function PPI1_D10 The multifunction net that typically functions as the D10 JP3.9/10, pin of PPI1 but, with a jumper, also can connect to the JP5.3/4, PDWN input of the OmniVision and Kodak camera inter- JP5.5/6 faces. (Bi) PPI1_D2 (Bi) PPI1_D3 (Bi) FLAG_SDA (Bi) FLAG_SCL_DIR_ CTRL (Input) PPI1_CLK (Output) PPI1_FS1 (Input) PPI1_FS2 (Input) SNAPSHOT_FODD_ SSEL (Bi) SCK (Input) Relevant Configuration Jumpers The multifunction net typically functions as the D2 pin of JP3.3/5/7, PPI1 but also can function as the data signal for the pro- JP5.3/4, JP5.5/6 cessor's 2-wire interface (TWI). Used to program the internal configuration registers of most video interfaces. The multifunction net typically functions as the D2 pin of JP3.4/6/8, PPI1 but also can function as the data signal for the pro- JP5.3/4, cessor's TWI. Used to program the internal configuration JP5.5/6 registers of most video interfaces. In systems whose processor does not have a TWI, the sig- JP3.3/5/7 nal connects to one of the processor's flag pins to emulate the TWI data pin and configure the internal registers of most video interfaces. In systems whose processor does not have a TWI, the sig- JP3.4/6/8 nal connects to one of the processor's flag pins to emulate the TWI clock signal and configure the internal registers of most video interfaces. The clock driving the EZ-KIT Lite's PPI1 clock input. The source of this clock can be PPI0_CLK, the on-board 27 MHz oscillator, or a socket accepting oscillators of other frequencies. JP4.1/2, JP4.3/4, JP4.5/6, JP4.7/8 The signal driven to the HS signal of the FPDI. The output going to the FPDI can be disabled by a jumper. JP8.1/3/5, JP8.7/8 The signal driven to the VS signal of the FPDI. The output going to the FPDI can be disabled by a jumper. JP8.2/4/6, JP8.7/8 The audio codec's SPI slave select signal; also can connect JP3.21/22 to the SNAPSHOT input of the Kodak interface or the FODD output of the OmniVision interface. The SPI serial clock used to program the control register of the AD1836A audio codec. Blackfin A-V EZ-Extender Manual 2-5 System Architecture Table 2-1. Signals of Expansion Interface Connectors (Cont'd) Net/Bus Name (Direction) Blackfin A-V EZ-Extender Function MOSI The SPI serial output data signal used to program the control register of the AD1836A audio codec. (Output) MISO (Output) RSCLK0 (Bi) RFS0 (Bi) DR0PRI (Output) DR0SEC (Output) TSCLK0 (Bi) TFS0 (Bi) DT0PRI Relevant Configuration Jumpers The SPI serial input data signal used to read the control register of the AD1836A audio codec. The processor's SPORT0 receive clock signal connected to the serial clock on the digital side of the audio codec's analog input. In I2S mode, the signal can connect to the TSCLK0 net. JP7.1/2 The processor's SPORT0 receive frame sync signal conJP7.1/2 nected to the frame sync on the digital side of the audio codec's analog input. In I2S mode, the signal can connect to the TFS0 net. A connection to the data output of the audio codec; can JP7.3/4 be disconnected with a jumper if needed for another purpose. A secondary connection to the data output of the audio codec. Can be disconnected with a jumper if needed for another purpose. JP7.5/6 The processor's SPORT0 transmit clock signal, connects to JP7.1/2 the serial clock on the digital side of the audio codec's analog output. In I2S mode, the signal can connect to the RSCLK0 net. The processor's SPORT0 transmit frame sync signal. Con- JP7.1/2 nects to the frame sync on the digital side of the audio codec's analog output. In I2S mode, the signal can connect to the RFS0 net. A connection to the data input of the audio codec. (Input) DT0SEC (Input) 2-6 A secondary connection to the data input of the audio codec. Blackfin A-V EZ-Extender Manual A-V EZ-Extender Hardware Reference Jumpers Before using the Blackfin A-V EZ-Extender, follow the procedure in "A-V EZ-Extender Setup" on page 1-2. Figure 2-2. Jumper Locations Figure 2-2 shows the jumper header locations. The jumper headers are divided to show each jumper's placement and rotation. The jumpers are described by the pins of the header on which the jumpers can be placed. Blackfin A-V EZ-Extender Manual 2-7 Jumpers For example, JP3.4/6/8 refers to a single jumper that can be placed across pins 4 and 6 (or pins 6 and 8) of JP3. The dark pin indicates pin 1 of each header. Video Test Loopback Jumpers (JP1.1/2, JP1.3/4, JP1.5/6) For test purposes only, the video test jumpers loop-back the video encoder's output signals to the video decoder's input signals. By default, none of the video test loopback jumpers are installed. Connector Voltage Selection Jumper (JP2) The camera module and LCD display interfaces can be powered via the extender. The actual voltage of the interfaces, 3.3V or 5V, is determined by the JP2 jumper's placement (see Table 2-2). Table 2-2. Jumper Locations and Connector Voltages Jumper Location Connector Voltage JP2.1/2 3.3V JP2.2/3 5V Not installed No power TWI Source Selection Jumpers (JP3.3/5/7, JP3.4/6/8) Due to the fact that some Blackfin processors feature a built-in 2-wire interface (TWI), while others need to emulate the interface with programmable flags, two jumpers are provided to plug the A-V EZ-Extender to both TWI sources (see Table 2-3). 2-8 Blackfin A-V EZ-Extender Manual A-V EZ-Extender Hardware Reference Table 2-3. Jumper Locations and TWI Interface Sources Jumper Location TWI Interface Source JP3.3/5 and JP3.4/6 Programmable flags JP3.5/7 and JP3.6/8 2-wire interface of the processor PDWN Connect Jumper (JP3.9/10) Depending on the application, the PDWN pin of the OmniVision and Kodak cameras can be left floating or controlled by a flag pin (see Table 2-4). Table 2-4. PWDN Pin Connections JP3.9/10 Jumper PDWN Connection Uninstalled PDWN Installed The PDWN functionality of the cameras is controlled by a flag pin of the processor. is not used and, by default, the cameras function in standard mode Decoder HSYNC Disconnect Jumper (JP3.11/12) To connect the horizontal sync signal of the video decoder to the PPI0 frame sync signal of the processor, install jumper JP3.11/12; otherwise, the decoder's horizontal sync is disconnected. Decoder VSYNC Connect Jumper (JP3.13/14) To connect the vertical sync signal of the video decoder to the PPI0 frame sync signal of the processor, install jumper JP3.13/14; otherwise, the decoder's vertical sync is disconnected. Blackfin A-V EZ-Extender Manual 2-9 Jumpers Encoder HREF Connect Jumper (JP3.15/16) To connect the horizontal sync signal of the video encoder to the PPI0 frame sync signal of the processor, install jumper JP3.15/16; otherwise, the encoder's horizontal reference is disconnected. Encoder VSYNC Connect Jumper (JP3.17/18) To connect the vertical sync signal of the video encoder to the PPI0 frame sync signal of the processor, install jumper JP3.17/18; otherwise, the encoder's vertical sync is disconnected. Decoder Output Enable Jumper (JP3.19/20) When installed, jumper JP3.19/20 enables the video decoder's data output signals on the VID_IN bus. SNAPSHOT_FODD Disconnect Jumper (JP3.21/22) The SNAPSHOT_FODD net of the Blackfin A-V EZ-Extender is a general-purpose flag pin. The flag pin connects to SNAPSHOT (the Kodak camera evaluation board's signal) and FODD (the OmniVision camera evaluation board' control signal). Do not install the jumper unless the processor needs to control these signals. The flag pin also connects to the SPI select pin of the AD1836A audio codec--do not install JP3.21/22 when using the audio interfaces. 2-10 Blackfin A-V EZ-Extender Manual A-V EZ-Extender Hardware Reference PPI Clock Setup Jumpers (JP4.1/2, JP4.3/4, JP4.5/6, JP4.7/8) The PPI_CLK signals of PPI0 and PPI1 are configured by the clock setup jumpers (see Table 2-5). For more information, refer to Figure 2-1 on page 2-4. Table 2-5. PPI Clock Setup Jumper Results Jumper Location Result JP4.1/2 Connects EXT_VID_CLK to the on-board 27 MHz oscillator. For more information about the EXT_VID_CLK signal, see the JP4.3/4 description. JP4.3/4 Connects PPI0_CLK to the EXT_VID_CLK net. The EXT_VID_CLK net is the external clock, which drives the input clock of all three camera module connectors, plus the flat panel display connector. Depending on the JP4 jumper installation, EXT_VID_CLK can be generated by the PIXEL_CLK net, the VDEC_CLKOUT net, a socket (U8), or the on-board 27 MHz oscillator. JP4.5/6 Connects VDEC_CLKOUT to PPI0_CLK; VDEC_CLKOUT drives the PPI0 clock when the video decoder is used. JP4.7/8 Connects the PIXEL_CLK net, which is an output from the three camera interfaces, to PPI0_CLK. PPI0 D8-15 Enable Jumper (JP5.1/2) The JP5.1/2 jumper, when is not installed, disables the upper eight bits of the PPI0 data bus. This allows the signals connected to the upper eight bits of the PPI data bus of the EZ-KIT Lite to be used elsewhere on the board. To disable and re-use the upper eight bits of the VID_IN and PPI0 data busses, install JP5.1/2. Blackfin A-V EZ-Extender Manual 2-11 Jumpers VID_OUT Data Bus Control Jumpers (JP5.3/4, JP5.5/6) The JP5.3/4 and JP5.5/6 jumpers are used together to set up the direction of and enable/disable the VID_OUT data bus drivers. Table 2-6 shows different combinations of JP5.3/4 and JP5.5/6. Table 2-6. Video Out Data Bus Control Jumper Combinations JP5.3/4 JP5.5/6 VID_OUT Status Uninstalled Uninstalled VID_OUT, PPI1 are all not driven; PPI0 depends on the state of JP9.2/4/6 Uninstalled Installed PPI1 drives VID_OUT Installed Uninstalled PPI0 drives VID_OUT Installed Installed PPI0 drives VID_OUT, and VID_OUT drives PPI1 (loop-back mode) PPI0_SYNC1 Direction Setup Jumper (JP6.1/3/5) The direction of the PPI0_SYNC1 signal can be either fixed or programmed, depending on the state of a general-purpose flag. Table 2-7 shows how to set up the PPI0_SYNC1 direction. Table 2-7. Setting Direction of PPI0_SYNC1 (JP6.1/3/5) Jumper Location PPI0_SYNC1 Direction JP6.1/3 Controlled by a flag pin JP6.3/5 Input to the processor Uninstalled Output from the processor 2-12 Blackfin A-V EZ-Extender Manual A-V EZ-Extender Hardware Reference PPI0_SYNC2 Direction Setup Jumper (JP6.2/4/6) The direction of the PPI0_SYNC2 signal can be either fixed or programmed, depending on the state of a general-purpose flag. Table 2-8 shows how to set the PPI0_SYNC2 direction. Table 2-8. Setting Direction of PPI0_SYNC2 (JP6.2/4/6) Jumper Location PPI0_SYNC2 Direction JP6.2/4 Controlled by a flag pin JP6.4/6 Input to the processor Uninstalled Output from the processor I 2 S Enable Jumper (JP7.1/2) When JP7.1/2 is installed, the SPORT signals are routed for I2S SPORT communication protocol mode. To accomplish this, the receive and transmit clocks of the processor are driven by the output clock of the AD1836A audio codec. The same is done for the frame sync signals. SPORT Data Connect Jumpers (JP7.3/4, JP7.5/6) The JP7.3/4 and JP7.5/6 jumpers connect data output pins (ASDATA1 and ASDATA2) of the audio codec to the primary and secondary SPORT data input pins of the processor. The audio codec is driving these pins; with the help of the JP7.3/4 and JP7.5/6 jumpers, the processor's pins can be re-used when the codec is disabled. Blackfin A-V EZ-Extender Manual 2-13 Jumpers VID_OUT Bus SYNC Source Select Jumpers (JP8.1/3/5, JP8.2/4/6) The source of the PPI frame sync signals depends on the PPI port driving the VID_OUT bus. When using PPI0, place the jumpers at JP8.1/3 and JP8.2/4. When using PPI1, place the jumpers at JP8.3/5 and JP8.4/6. VID_OUT Bus SYNC Enable Jumper (JP8.7/8) To enable the VID_OUT frame sync signals, install JP8.7/8. AV_RESET Source Jumper (JP9.1/3/5) The source of ICs reset on the Blackfin A-V EZ-Extender is controlled by either a flag pin or a system reset; the latter also resets the Blackfin processor (see Table 2-9). Table 2-9. Jumper Reset Sources Jumper Location Reset Source JP9.1/3 Flag pin multiplexed with PPI1_D11 JP9.3/5 System reset generator Uninstalled ICs are not reset 2-14 Blackfin A-V EZ-Extender Manual A-V EZ-Extender Hardware Reference PPI0_D Direction Setup Jumper (JP9.2/4/6) The direction of the PPI0_D[15:0] signals can be a fixed direction or can be programmed, depending on the state of a general-purpose flag. Table 2-10 shows how to set up the PPI0_D[15:0] direction. Table 2-10. Setting Direction of PPI0_D[15:0] (JP9.2/4/6) Jumper Location PPI0_D[15:0] Direction JP9.2/4 Controlled by a flag pin JP9.4/6 Input to the processor Uninstalled Output from the processor Audio Loopback Jumpers (JP10.1/2, JP10.3/4) The JP10.1/2 and JP10.3/4 jumpers loop-back audio input to output for test purposes and should not be installed. Blackfin A-V EZ-Extender Manual 2-15 Jumpers 2-16 Blackfin A-V EZ-Extender Manual A A-V EZ-EXTENDER BILL OF MATERIALS The bill of materials corresponds to "A-V EZ-Extender Schematic" on page B-1. Ref. Qty. Description Reference Designator Manufacturer Part Number 1 1 SN74AHC1G00 SOT23-5 U9 TI SN74AHC1G00DBVR 2 1 12.288MHZ OSC003 U18 DIGI-KEY SG-8002CA-PCC-ND (12.288M) 3 5 SN74LVC1G125 SOT23-5 U15,U17,U19,U2930 TI 74LVC1G125DBVRE4 4 1 27MHZ OSC003 U1 DIGI-KEY SG-8002CA-PCC-ND (27.00M) 5 1 SN74LVC1G32 SOT23-5 U6 TI SN74LVC1G32DBVRE4 6 1 74LVTH16244MT D TSSOP48 U10 FAIRCHILD 74LVTH16244MTD 7 3 74LVTH16245MT D TSSOP48 U11,U14,U16 FAIRCHILD 74LVTH16245MTD 8 1 ADP3336ARMZ MSOP8 VR1 ANALOG DEVICES ADP3336ARMZ-REE 9 1 10MA AD1580BRTZ SOT23D D1 ANALOG DEVICES AD1580BRTZ-REEL7 10 3 AD8061ARTZ SOT23-5 U3-5 ANALOG DEVICES AD8061ARTZ-REEL Blackfin A-V EZ-Extender Manual A-1 Ref. Qty. Description Reference Designator Manufacturer Part Number 11 8 AD8606ARZ SOIC8 U20-23,U25-28 ANALOG DEVICES AD8606ARZ 12 1 AD1836AASZ MQFP52 U24 ANALOG DEVICES AD1836AASZ 13 1 ADV7179KCPZ LFCSP40 U7 ANALOG DEVICES ADV7179KCPZ 14 1 ADV7183BKSTZ LQFP80 U2 ANALOG DEVICES ADV7183BKSTZ 15 1 DIP 8 DIP8SOC U8 MILL-MAX 614-43-308-31-007000 16 3 0.05 45x2 CON018 P1-3 SAMTEC TFC-145-32-F-D 17 3 .05 45X2 CON019 J1-3 SAMTEC SFC-145-T2-F-D-A 18 1 RCA 3X2 CON024 J7 SWITCHCRAFT PJRAS3X2S01X 19 5 IDC 3X2 IDC3X2_SMT JP1,JP5-7,JP9 SAMTEC TSM-103-01-T-DV 20 1 IDC 16X2 IDC16X2RASOC J4 SAMTEC SSW-116-02-F-D-RA 21 1 IDC 13X2 IDC13X2_M_SMT JP3 SAMTEC TSM-113-01-T-DV 22 2 IDC 4X2 IDC4X2_M_SMT JP4,JP8 SAMTEC TSM-104-01-T-DV 23 1 FPDI 31PIN CON034 P6 FCI 68737-428HLF 24 1 IDC 13x2RA IDC13x2_F_RA J6 SAMTEC SSW-113-02-F-D-RA 25 1 IDC 3X1 IDC3X1 JP2 FCI 90726-403HLF 26 1 IDC 2X2 IDC2X2 JP10 SULLINS PBC02DAAN 27 8 0.22UF 25V 10% 0805 C73,C85,C101, C112,C120-121, C135,C138 AVX 08053C224FAT 28 1 33 1/10W 5% 0805 R49 VISHAY CRCW080533R0JNEA A-2 Blackfin A-V EZ-Extender Manual A-V EZ-Extender Bill of Materials Ref. Qty. Description Reference Designator Manufacturer Part Number 29 1 1.5K 1/10W 5% 0805 R1 VISHAY CRCW08051K50FKEA 30 6 10UF 16V 10% B CT1-4,CT12-13 AVX TAJB106K016R 31 5 600 100MHZ 200MA 0603 FER4-8 DIGI-KEY 490-1014-2-ND 32 4 600 100MHZ 500MA 1206 FER1-3,FER9 STEWARD HZ1206B601R-10 33 10 10UF 16V 20% CAP002 CT5-11,CT14-16 PANASONIC EEE1CA100SR 34 2 22 1/10W 5% 0805 R53,R55 VISHAY CRCW080522R0JNEA 35 6 0.68UH 10% 0805 L1-3,L7-9 MURATA LQM21NNR68K10D 36 1 .082UF 50V 5% 0805 C5 AVX 08055C823JAT2A 37 3 2.2UH 10% 0805 L4-6 DIGI-KEY 490-1119-2-ND 38 4 22 125MW 5% RNS001 RN1-4 CTS 744C083220JP 39 1 147.0K 1/10W 1% 0805 R36 DIGI-KEY 311-147KCRTR-ND 40 1 76.8K 1/10W 1% 0805 R38 DIGI-KEY 311-76.8KCRTR-ND 41 1 1.2K 1/16W 5% 0402 R42 PANASONIC ERJ-2GEJ122X 42 57 0.1UF 16V 10% 0603 C1,C4,C7-8,C10-15, C17,C19,C22-23, C26,C30,C32-34, C37-38,C40,C43-44, C46-49,C51-57, C60-69,C75-76,C78, C81,C99,C115, C124,C130-132, C144-145 AVX 0603YC104KAT2A Blackfin A-V EZ-Extender Manual A-3 Ref. Qty. Description Reference Designator Manufacturer Part Number 43 11 0.01UF 16V 10% 0603 C2-3,C6,C16,C25, C29,C36,C41,C50, C58,C110 AVX 0603YC103KAT2A 44 5 10UF 10V +80/-20% 0805 C42,C45,C59, C79-80 PANASONIC ECJ-2FF1A106Z 45 2 1UF 16V 10% 0603 C27,C39 PANASONIC ECJ-1VB1C105K 46 12 330PF 50V 5% 0603 C18,C20-21,C28, C31,C35,C98,C104, C107-108,C133, C137 AVX 06035A331JAT2A 47 3 22 1/10W 5% 0603 R146-148 VISHAY CRCW060322R0JNEA 48 19 10K 1/10W 5% 0603 R3-4,R10,R32,R37, R44-45,R47,R51, R54,R56-60,R107, R141,R149-150 VISHAY CRCW060310K0JNEA 49 2 100K 1/10W 5% 0603 R39-40 VISHAY CRCW0603100KJNEA 50 8 0 1/10W 5% 0603 R2,R15,R20,R25, R111,R115,R130, R135 PHYCOMP 232270296001L 51 1 10 1/10W 5% 0603 R143 VISHAY CRCW060310R0JNEA 52 6 1K 1/10W 5% 0603 R13-14,R18-19,R2324 DIGI-KEY 311-1.0KGRTR-ND 53 4 237.0 1/10W 1% 0603 R64,R70,R106,R110 DIGI-KEY 311-237HRTR-ND 54 4 750.0K 1/10W 1% 0603 R65,R69,R127,R129 DIGI-KEY 311-750KHRTR-ND 55 6 11.0K 1/10W 1% 0603 R82,R90,R93-94, R123,R126 DIGI-KEY 311-11.0KHRTR-ND 56 12 5.49K 1/10W 1% 0603 R75,R83,R86-87, R89,R99-101,R116, R119,R131-132 DIGI-KEY 311-5.49KHRTR-ND A-4 Blackfin A-V EZ-Extender Manual A-V EZ-Extender Bill of Materials Ref. Qty. Description Reference Designator Manufacturer Part Number 57 6 3.32K 1/10W 1% 0603 R81,R91-92,R95, R124-125 DIGI-KEY 311-3.32KHRTR-ND 58 6 1.65K 1/10W 1% 0603 R74,R84-85,R88, R117-118 DIGI-KEY 311-1.65KHRTR-ND 59 6 49.9K 1/10W 1% 0603 R96-97,R108-109, R137-138 DIGI-KEY 311-49.9KHRTR-ND 60 6 604.0 1/10W 1% 0603 R98,R102-104,R133, R136 DIGI-KEY 311-604HRTR-ND 61 16 5.76K 1/10W 1% 0603 R61-63,R67,R72-73, R76-77,R105,R120122,R128,R134, R139-140 DIGI-KEY 311-5.76KHRTR-ND 62 8 120PF 50V 5% 0603 C71,C74,C82-83, C127-128,C141, C143 AVX 06035A121JAT2A 63 12 100PF 50V 5% 0603 C77,C91-92,C97, C105-106,C109, C118,C129,C134, C13 AVX 06035A101JAT2A 64 10 1000PF 50V 5% 0603 C9,C24,C72,C86, C93,C100,C103, C111,C117,C119 PANASONIC ECJ-1VC1H102J 65 6 220PF 50V 5% 0603 C87,C94-96, C125-126 PANASONIC ECJ-1VC1H221J 66 6 680PF 50V 5% 0603 C84,C88-90, C122-123 PANASONIC ECJ-1VC1H681J 67 6 2200PF 50V 5% 0603 C102,C113-114, C116,C140,C142 PANASONIC ECJ-1VB1H222K 68 7 33.0 1/10W 1% 0603 R5,R8,R33,R68, R142,R144-145 DIGI-KEY 311-33.0HRTR-ND 69 6 2.74K 1/10W 1% 0603 R71,R78-80, R112-113 DIGI-KEY 311-2.74KHRTR-ND Blackfin A-V EZ-Extender Manual A-5 Ref. Qty. Description Reference Designator Manufacturer Part Number 70 12 75.0 1/10W 1% 0603 R11-12,R16-17,R2122,R26-31 DALE CRCW060375R0FKEA 71 1 680 1/8W 5% 1206 R114 VISHAY CRCW1206680RFNEA 72 1 150.0 1/8W 1% 1206 R41 VISHAY CRCW1206150RFKEA 73 1 GREEN LED001 LED1 PANASONIC LN1361CTR 74 2 3.5MM DUAL_STEREO CON066 J8-J9 SWITCHCRAFT 35RAPC7JS 75 1 3.5MM STEREO_JACK CON_SJ-3523-SMT J10 DIGI-KEY CP-3523SJCT-ND A-6 Blackfin A-V EZ-Extender Manual A B C D 1 1 2 2 Blackfin A-V EZ-Extender Schematic 3 3 ANALOG DEVICES 4 Title Size A B C Nashua, NH 03063 4 PH: 1-800-ANALOGD BLACKFIN A-V EZ-EXTENDER TITLE Board No. C Date 20 Cotton Road Rev A0193-2004 2.1 Sheet 07-06-2011_15:05 D 1 of 12 A B C 3.3V EXPANSION INTERFACE (TYPE B) 5V 1 D Expanison Connector 1 Expanison Connector 2 Bottom Of Board Top Of Board Bottom Of Board Top Of Board P1_[5:86] P1 P2_[5:86] J1 1 2 P2 2 1 4 3 6 5 P1_5 P2_5 P2_7 1 2 3 4 5 6 P2_6 P2_6 7 8 P2_8 P2_8 9 10 11 12 13 14 3 4 P1_5 5 6 P1_6 P1_7 7 8 P1_8 P1_8 8 7 P1_7 P1_9 9 10 P1_10 P1_10 10 9 P1_9 P1_11 11 12 P1_12 P1_12 12 11 P1_11 P1_13 13 14 P1_14 P1_14 14 13 P1_13 P1_15 15 16 P1_16 P1_16 16 15 P1_15 P2_15 15 16 P2_16 P2_16 P1_17 17 18 P1_18 P1_18 18 17 P1_17 P2_17 17 18 P2_18 P1_19 19 20 P1_20 P1_20 20 19 P1_19 P2_19 19 20 P2_20 P1_21 21 22 P1_22 P1_22 22 21 P1_21 P2_21 21 22 P2_22 P2_23 23 24 25 26 P2_26 P2_26 P2_27 27 28 P2_28 P2_29 29 30 P1_6 SCK P2_11 J2 2 1 4 3 6 5 P2_5 P2_7 8 7 10 9 12 11 14 13 16 15 P2_15 P2_18 18 17 P2_17 P2_20 20 19 P2_19 P2_22 22 21 P2_21 24 23 P2_23 26 25 P2_28 28 27 P2_27 P2_30 P2_30 30 29 P2_29 MOSI MOSI MISO MISO SCK P2_11 P2_23 2 3 P1_23 23 24 P1_24 P1_24 24 23 P1_23 P1_25 25 26 P1_26 P1_26 26 25 P1_25 P1_27 27 28 P1_28 P1_28 28 27 P1_27 P1_29 29 30 P1_30 P1_30 30 29 P1_29 P1_31 31 32 P1_32 P1_32 32 31 P1_31 P2_31 31 32 P2_32 P2_32 32 31 P2_31 P1_33 33 34 P1_34 P1_34 34 33 P1_33 P2_33 33 34 P2_34 P2_34 34 33 P2_33 P1_35 35 36 P1_36 P1_36 36 35 P1_35 35 36 36 35 37 38 38 37 39 40 40 39 41 42 42 41 PPI0_SYNC1 R149 10K 0603 DR0SEC PPI0_SYNC2 PPI0_SYNC2 DT0SEC DT0SEC DT0PRI DT0PRI PPI0_SYNC1 2 DR0SEC 37 38 38 37 P1_39 39 40 P1_40 P1_40 40 39 P1_39 P1_41 41 42 P1_42 P1_42 42 41 P1_41 P1_43 43 44 P1_44 P1_44 44 43 P1_43 PPI0_D4 43 44 PPI0_D5 PPI0_D5 44 43 PPI0_D4 P1_45 45 46 P1_46 P1_46 46 45 P1_45 PPI0_D6 45 46 PPI0_D7 PPI0_D7 46 45 PPI0_D6 P1_47 47 48 P1_48 P1_48 48 47 P1_47 PPI0_D8 47 48 PPI0_D9 PPI0_D9 48 47 PPI0_D8 P1_49 49 50 P1_50 P1_50 50 49 P1_49 PPI0_D10 49 50 PPI0_D11 PPI0_D11 50 49 PPI0_D10 P1_51 51 52 P1_52 P1_52 52 51 P1_51 PPI0_D12 51 52 PPI0_D13 PPI0_D13 52 51 PPI0_D12 P1_53 53 54 P1_54 P1_54 54 53 P1_53 PPI0_D14 53 54 PPI0_D15 PPI0_D15 54 53 P1_55 55 56 P1_56 P1_56 56 55 P1_55 55 56 56 55 P1_57 57 58 P1_58 P1_58 58 57 P1_57 57 58 P1_59 59 60 P1_60 P1_60 60 59 P1_59 P2_59 59 60 P2_60 P1_61 61 62 P1_62 P1_62 62 61 P1_61 P2_61 61 62 P2_62 P1_63 63 64 P1_64 P1_64 64 63 P1_63 P2_63 63 64 P1_65 65 66 P1_66 P1_66 66 65 P1_65 P2_65 65 66 P1_67 67 68 P1_68 P1_68 68 67 P1_67 P2_67 67 P1_69 69 70 P1_70 P1_70 70 69 P1_69 P2_69 69 71 72 PPI0_D0 PPI0_D0 72 71 P2_71 PPI0_D1 73 74 PPI0_D2 PPI0_D2 74 73 PPI0_D1 P2_73 PPI0_D3 75 76 P1_76 P1_76 76 75 PPI0_D3 P1_77 77 78 P1_78 P1_78 78 77 P1_77 P1_79 79 80 P1_80 P1_80 80 79 P1_79 P1_81 81 82 P1_82 P1_82 82 81 P1_83 83 84 P1_84 P1_84 84 P1_85 85 86 P1_86 P1_86 86 87 88 88 89 90 90 CON018 DR0PRI RFS0 RSCLK0 P2_55 TFS0 TFS0 TSCLK0 TSCLK0 SNAPSHOT_FODD_SSEL DR0PRI RFS0 RSCLK0 PPI0_D14 P2_55 58 57 P2_60 60 59 P2_59 P2_62 62 61 P2_61 P2_64 P2_64 64 63 P2_63 P2_66 P2_66 66 65 P2_65 68 P2_68 P2_68 68 67 P2_67 70 P2_70 P2_70 70 69 P2_69 71 72 P2_72 P2_72 72 71 P2_71 73 74 P2_74 P2_74 74 73 P2_73 75 76 76 75 P2_77 77 78 P2_78 P2_78 78 77 P2_77 P2_79 79 80 P2_80 P2_80 80 79 P2_79 P1_81 P2_81 81 82 P2_82 P2_82 82 81 P2_81 83 P1_83 P2_83 83 84 P2_84 P2_84 84 83 P2_83 85 P1_85 P2_85 85 86 P2_86 P2_86 86 85 P2_85 87 87 88 88 87 89 89 90 90 89 FLAG_SDA PPI0_CLK CON019 FLAG_SCL_DIR_CTRL CON018 FLAG_SDA 3 CON019 PPI0_D[15:0] 3.3V 5V C59 10UF 0805 4 C45 10UF 0805 ANALOG DEVICES C48 0.1UF 0603 C46 0.1UF 0603 Title Size A B C Nashua, NH 03063 4 PH: 1-800-ANALOGD BLACKFIN A-V EZ-EXTENDER EXPANSION INTERFACE (1, 2) Board No. C Date 20 Cotton Road Rev A0193-2004 2.1 Sheet 07-06-2011_15:16 D 2 of 12 A B C D EXPANSION INTERFACE (TYPE B) 5V 3.3V 1 5V 1 Expanison Connector 2 Bottom Of Board Top Of Board PPI1_D[15:0] POWER LED1 GREEN LED001 P3_[1:90] P3 PPI1_D1 1 2 PPI1_D0 3 4 P3_5 5 6 P3_6 P3_7 P3_8 PPI1_D0 P3_6 1 4 3 6 5 P3_5 P3_7 PPI1_D1 R114 680 1206 7 8 8 7 PPI1_D3 9 10 PPI1_D2 PPI1_D2 10 9 PPI1_D3 PPI1_D5 11 12 PPI1_D4 PPI1_D4 12 11 PPI1_D5 PPI1_D7 13 14 PPI1_D6 PPI1_D6 14 13 PPI1_D7 PPI1_D9 15 16 PPI1_D8 PPI1_D8 16 15 PPI1_D9 PPI1_D11 17 18 PPI1_D10 PPI1_D10 18 17 PPI1_D11 PPI1_D13 19 20 PPI1_D12 PPI1_D12 20 19 PPI1_D13 PPI1_D15 21 22 PPI1_D14 PPI1_D14 22 21 PPI1_D15 23 24 24 23 25 26 26 25 28 27 30 29 P3_29 PPI1_CLK 2 27 28 29 30 P3_31 31 32 P3_32 P3_32 32 31 P3_31 P3_33 33 34 P3_34 P3_34 34 33 P3_33 P3_35 35 36 P3_36 P3_36 36 35 P3_35 P3_37 37 38 P3_38 P3_38 38 37 P3_37 P3_39 39 40 40 39 P3_39 P3_45 41 42 43 44 45 P3_47 46 47 P3_49 48 49 P3_51 50 51 P3_53 52 53 54 P3_42 P3_46 P3_48 P3_50 P3_52 P3_54 RESET PPI1_FS2 P3_28 PPI1_CLK P3_29 PPI1_FS1 P3_28 P3_8 J3 2 P3_42 P3_46 P3_48 P3_50 P3_52 P3_54 42 41 44 43 46 48 50 52 54 45 47 49 51 53 5V PPI1_FS1 3.3V P3_45 P3_49 PWDN P3_51 VDEC_HS R37 10K 0603 P3_53 VDEC_VS P3_56 P3_56 56 55 P3_55 P3_57 57 58 P3_58 P3_58 58 57 P3_57 VENC_VSYNC P3_59 59 60 P3_60 P3_60 60 59 P3_59 P3_63 63 64 65 66 P3_64 P3_67 67 68 P3_68 P3_69 69 70 P3_71 71 P3_73 P3_75 P3_62 P3_64 62 61 DEC_DATA_OE SNAPSHOT_FODD P3_61 64 63 66 65 P3_68 68 67 P3_67 P3_70 P3_70 70 69 P3_69 72 P3_72 P3_72 72 71 P3_71 73 74 P3_74 P3_74 74 73 P3_73 75 76 P3_76 P3_76 76 75 P3_75 P3_77 77 78 P3_78 P3_78 78 77 P3_77 P3_79 79 80 P3_80 P3_80 80 79 P3_79 P3_81 81 82 P3_82 P3_82 82 81 P3_81 P3_83 83 84 P3_84 P3_84 84 83 P3_83 P3_85 85 86 P3_86 P3_86 86 85 P3_85 87 88 88 87 89 90 P3_90 P3_90 90 89 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 PPI1_D2 P3_47 56 P3_62 2 SDA 55 62 1 FLAG_SDA P3_55 61 2 JP3 VENC_HREF P3_61 3.3V FLAG_SCL_DIR_CTRL SCL PPI1_D3 to TWI of ADSP-BF537 EZ-KIT Lite PPI1_D10 VID_IN_SYNC1_HREF VID_IN_SYNC2_VSYNC SNAPSHOT_FODD_SSEL P3_63 IDC13X2_M_SMT 9 Jumpers 3 P3_89 CON018 3.3V 4 C80 10UF 0805 3 P3_89 CON019 5V C81 0.1UF 0603 C79 10UF 0805 ANALOG DEVICES C78 0.1UF 0603 Title Size A B C Nashua, NH 03063 4 PH: 1-800-ANALOGD BLACKFIN A-V EZ-EXTENDER EXPANSION INTERFACE (3) Board No. C Date 20 Cotton Road Rev A0193-2004 2.1 Sheet 07-06-2011_15:16 D 3 of 12 A B C D PPI0_D[15:0] RN1 1 1 1 R1A R1B 2 R2A R2B 3 R3A R3B 4 R4A R4B 8 PPI0_D0 7 PPI0_D1 6 PPI0_D2 PPI0_D0 47 5 PPI0_D3 PPI0_D1 46 PPI0_D2 44 PPI0_D3 43 PPI0_D4 41 PPI0_D5 40 PPI0_D6 38 PPI0_D7 37 PPI0_D8 36 VID_OUT_D[15:0] U10 U11 VID_IN_D0 VID_IN_D[15:0] 2 1B1 VID_IN_D1 2 1A1 3 5 VID_IN_D3 6 8 9 VID_IN_D6 11 VID_IN_D7 12 VID_IN_D10 16 19 VID_IN_D14 22 VID_IN_D15 23 R3B R4B PPI0_D4 7 PPI0_D5 6 PPI0_D6 5 VID_OUT_D0 1A2 3 1Y2 VID_OUT_D1 1A3 5 1Y3 VID_OUT_D2 1A4 6 1Y4 VID_OUT_D3 2A1 8 2Y1 VID_OUT_D4 2A2 9 2Y2 VID_OUT_D5 2A3 11 2Y3 VID_OUT_D6 2A4 12 2Y4 VID_OUT_D7 3A1 13 3Y1 VID_OUT_D8 3A2 14 3Y2 VID_OUT_D9 3A3 16 3Y3 VID_OUT_D10 3A4 17 3Y4 VID_OUT_D11 4A1 19 4Y1 VID_OUT_D12 4A2 20 4Y2 VID_OUT_D13 4A3 22 4Y3 VID_OUT_D14 4A4 23 4Y4 VID_OUT_D15 PPI0_D7 RN3 1 37 2 36 3 35 4 R1A R1B R2A R2B R3A R3B R4A R4B 8 PPI0_D8 7 PPI0_D9 6 PPI0_D10 5 PPI0_D11 PPI0_D9 35 PPI0_D10 33 PPI0_D11 32 PPI0_D12 30 PPI0_D13 29 PPI0_D14 27 PPI0_D15 26 33 2A3 22 RNS001 32 2A4 30 2B5 20 R2B 8 38 2A2 2B4 VID_IN_D13 22 RNS001 2A1 2B3 VID_IN_D12 40 1A8 2B2 17 41 R4A 1A7 2B1 VID_IN_D11 4 1A6 1B8 14 R3A R1B 1A5 1B7 VID_IN_D9 3 1A4 1B6 13 R2A 43 1B5 VID_IN_D8 2 1A3 1B4 VID_IN_D5 R1A 44 1B3 VID_IN_D4 1 1A2 2 1Y1 RN2 46 1B2 VID_IN_D2 22 RNS001 47 1A1 1 2A5 2B6 29 2 27 3 26 4 2A6 2B7 2A7 2B8 RN4 2A8 R1A R1B R2A R2B R3A R3B R4A R4B 8 PPI0_D12 7 PPI0_D13 6 PPI0_D14 5 PPI0_D15 1 PPI0_EN OE1 48 25 1 T/R1 22 RNS001 VID_IN_DIR_CTRL 2 OE2 OE3 24 OE4 24 T/R2 74LVTH16244MTD TSSOP48 48 OE1 25 OE2 PPI0_HI_EN 74LVTH16245MTD TSSOP48 PPI1_D[15:0] U16 3.3V 3.3V R46 10K 0603 DNP R44 10K 0603 R54 10K 0603 JP9 3 1 PPI1_D11 AV_RESET PPI1_D0 47 PPI1_D1 46 PPI1_D2 44 PPI1_D3 43 PPI1_D4 41 PPI1_D5 40 PPI1_D6 38 PPI1_D7 37 PPI1_D8 36 PPI1_D9 35 PPI0_EN PPI1_D10 33 PPI1_EN PPI1_D11 32 PPI1_D12 30 PPI1_D13 29 PPI1_D14 27 PPI1_D15 26 3.3V R57 10K 0603 R59 10K 0603 JP5 2 3 4 5 6 1 FLAG_SCL_DIR_CTRL VID_IN_DIR_CTRL IDC3X2_SMT 2 3 4 5 6 PPI0_HI_EN 2 1B1 VID_OUT_D0 1A2 3 1B2 VID_OUT_D1 1A3 5 1B3 VID_OUT_D2 1A4 6 1B4 VID_OUT_D3 1A5 8 1B5 VID_OUT_D4 1A6 9 1B6 VID_OUT_D5 1A7 11 1B7 VID_OUT_D6 1A8 12 1B8 VID_OUT_D7 2A1 13 2B1 VID_OUT_D8 2A2 14 2B2 VID_OUT_D9 2A3 16 2B3 VID_OUT_D10 2A4 17 2B4 VID_OUT_D11 2A5 19 2B5 VID_OUT_D12 2A6 20 2B6 VID_OUT_D13 2A7 22 2B7 VID_OUT_D14 2A8 23 2B8 VID_OUT_D15 IDC3X2_SMT 1A1 R150 10K 0603 3 1 PPI0_EN T/R1 24 48 25 PPI1_EN T/R2 OE1 OE2 74LVTH16245MTD TSSOP48 3.3V 4 C62 0.1UF 0603 3.3V C56 0.1UF 0603 C55 0.1UF 0603 3.3V C61 0.1UF 0603 C66 0.1UF 0603 ANALOG DEVICES C76 0.1UF 0603 Title 74LVTH16245MTD SN74ALVTH16244 Size SN74ALVTH16244 A B C Nashua, NH 03063 4 PH: 1-800-ANALOGD BLACKFIN A-V EZ-EXTENDER DATA ROUTING Board No. C Date 20 Cotton Road Rev A0193-2004 2.1 Sheet 10-06-2011_09:57 D 4 of 12 A B C D Video In Frame Sync Setup R53 22 0805 U14 3.3V 2 VID_IN_SYNC1_HREF 47 1B1 1A1 3 1B2 1A2 5 44 1B3 43 1B4 1A4 8 41 1B5 1A5 9 40 1B6 38 1B7 1A7 12 R51 10K 0603 PPI Clock Setup 37 1B8 1A8 13 VID_IN_SYNC2_VSYNC R56 10K 0603 1A6 11 R55 22 0805 3.3V 1A3 6 1 PPI0_SYNC1 46 36 2B1 2A1 14 PPI0_SYNC2 2A2 16 JP6 1 2 3 4 5 6 1 OE/NC 33 2B3 VID_IN_SYNC1_DIR_CTL 32 2B4 2A4 19 5 OUT DIP8SOC 2A3 17 R49 33 0805 U8 FLAG_SCL_DIR_CTRL 35 2B2 1 R43 10K 0603 DNP VID_IN_SYNC2_DIR_CTL 30 2B5 2A5 20 IDC3X2_SMT 3.3V 29 2B6 2A6 22 2 Jumpers 27 2B7 2A7 23 26 2B8 2A8 1 T/R1 VID_IN_SYNC1_DIR_CTL T/R2 24 R48 10K 0603 VID_IN_SYNC2_DIR_CTL 48 OE1 25 OE2 74LVTH16245MTD TSSOP48 27MHZ_CLK 2 R148 22 0603 1 U19 4 SN74LVC1G125 SOT23-5 JP4 1 2 3 4 5 6 7 8 EXT_VID_CLK VDEC_CLKOUT PIXEL_CLK IDC4X2_M_SMT 2 2 4 Jumpers TP9 VID_OUT_SYNC_EN 2 VID_OUT_SYNC1 R146 22 0603 1 U15 U17 4 VID_OUT_SYNC1_HREF VID_OUT_SYNC2 SN74LVC1G125 SOT23-5 R147 22 0603 1 VID_OUT_SYNC_EN TP10 2 4 R50 0 0805 VID_OUT_SYNC2_VSYNC SN74LVC1G125 SOT23-5 PPI0_CLK 3.3V Video Out Frame Sync Setup R58 10K 0603 3 3 TP11 TP12 JP8 PPI0_SYNC1 VID_OUT_SYNC1 PPI1_FS1 VID_OUT_SYNC_EN 1 2 3 4 5 6 7 8 PPI0_SYNC2 VID_OUT_SYNC2 PPI1_FS2 IDC4X2_M_SMT 3 Jumpers R52 0 0805 EXT_VID_CLK 3.3V 4 3.3V C51 0.1UF 0603 3.3V C64 0.1UF 0603 3.3V C67 0.1UF 0603 3.3V C69 0.1UF 0603 C65 0.1UF 0603 PPI1_CLK 3.3V C68 0.1UF 0603 ANALOG DEVICES C63 0.1UF 0603 Title Size OSC SOC SN74LVC1G125 SN74LVC1G125 SN74LVC1G125 74LVTH16245MTD Date A B C Nashua, NH 03063 4 PH: 1-800-ANALOGD BLACKFIN A-V EZ-EXTENDER FS/CLK CONFIG Board No. C SN74LVC1G125 20 Cotton Road Rev A0193-2004 2.1 Sheet 07-06-2011_15:16 D 5 of 12 A B C CONN_SUPPLY D Micron Interface VID_IN_D[15:0] J6 VID_IN_D1 2 1 VID_IN_D0 VID_IN_D3 4 3 VID_IN_D2 VID_IN_D5 6 5 VID_IN_D4 VID_IN_D7 8 7 VID_IN_D6 VID_IN_D9 10 9 VID_IN_D8 12 11 14 13 16 15 18 17 20 19 22 21 24 23 26 25 1 5V 3.3V Micron Interface J4 J6 CONN_SUPPLY TP13 1 JP2 AV_RESET SDA EXT_VID_CLK 1 VID_IN_SYNC1_HREF 2 3 VID_IN_SYNC2_VSYNC OmniVision Interface SCL IDC3X1 1 Jumper C44 0.1UF 0603 C42 10UF 0805 PIXEL_CLK IDC13X2_F_RA Flat Panal Display Interface CONN_SUPPLY CONN_SUPPLY P6 J4 VID_IN_D0 2 VID_IN_D2 VID_IN_D4 VID_IN_D6 Y0 2 1 Y1 Y2 4 3 Y3 Y4 6 5 Y5 Y6 8 7 Y7 PWDN PWDN 10 9 VID_IN_D1 VID_IN_D3 SCL EXT_VID_CLK VID_IN_D8 VID_IN_D10 VID_IN_D12 VID_IN_D14 12 11 FODD SCL 14 13 HREF GND 16 15 VSYNC GND 18 17 PCLK EXCLK 20 19 VIN 22 21 VIN UV0 24 23 UV1 UV2 26 25 UV3 UV4 28 27 UV5 UV6 30 29 UV7 32 31 VCC2 29 CK U9 VID_IN_D7 RESET SDA 28 VID_IN_D5 1 4 SNAPSHOT_FODD see JP3 2 2 EXT_VID_CLK 3 HS 4 VS AV_RESET 2 SDA VCC1 SN74AHC1G00 SOT23-5 VID_IN_SYNC1_HREF R0 VID_IN_SYNC2_VSYNC R1 PIXEL_CLK OmniVision Interface 8 R2 9 R3 VID_OUT_D1 VID_OUT_D3 11 VID_OUT_D4 13 VID_OUT_D5 14 VID_OUT_D6 15 G2 16 G3 VID_OUT_D7 17 G4 18 G5 VID_OUT_D9 G0 VID_IN_D13 G1 B0 VID_OUT_D8 VID_OUT_D10 20 CONN_SUPPLY 21 VID_OUT_D11 22 VID_OUT_D12 23 B3 24 B4 VID_OUT_D13 25 B5 VID_OUT_D15 R4 10K 0603 R2 0 0603 R9 10K 0603 DNP R7 10K 0603 DNP R6 10K 0603 DNP B1 B2 3 VID_OUT_D[15:0] VID_OUT_D2 10 VID_IN_D11 IDC16X2RASOC 6 VID_OUT_D0 R5 VID_IN_D15 VID_OUT_SYNC2_VSYNC 7 R4 VID_IN_D9 VID_OUT_SYNC1_HREF ENAB 3 VID_OUT_D14 27 30 31 GND1 1 GND2 5 GND3 12 GND4 19 GND5 26 CON034 3.3V ANALOG DEVICES C60 0.1UF 0603 4 Title Size Date A B C Nashua, NH 03063 4 PH: 1-800-ANALOGD BLACKFIN A-V EZ-EXTENDER PPI0 SETUP Board No. C SN74AHC1G00 20 Cotton Road Rev A0193-2004 2.1 Sheet 07-06-2011_15:16 D 6 of 12 VIDEO_AVIN4 VIDEO_AVIN5 1 2 3 4 5 6 VIDEO_DAC_A VIDEO_DAC_C VIDEO_DAC_B DAC_A JP1 VIDEO_AVIN1 C DAC_B B DAC_C A IDC3X2_SMT (WHITE) OUT D DAC A DAC B DAC C Composite Video CVSB CVSB C Component Video G B R Differential Component Video Y U V S Video Y C (RED) IN AVIN1 AVIN4 1 AVIN5 1 R13 1K 0603 A3V VIDEO_DAC_A U3 4 L1 0.68UH 0805 L4 2.2UH 0805 J7 5 L7 0.68UH 0805 1 3 3.3V VIDEO ENCODER U7 VAA1 VAA2 VAA3 VAA4 VAA5 2 VID_OUT_D7 VID_OUT_D[7:0] VID_OUT_D6 5 4 VID_OUT_D5 3 VID_OUT_D4 39 VID_OUT_D3 38 VID_OUT_D2 37 VID_OUT_D1 36 VID_OUT_D0 35 1 DAC_A P6 DAC_B P5 20 DAC_C P3 COMP P2 VREF P1 RSET 22 SDA 21 SCL CLOCK FIELD/VSYNC GND1 ALSB GND2 SDATA GND3 SCLOCK GND6 33 2 10 18 25 C54 0.1UF 0603 R47 10K 0603 C47 0.1UF 0603 R42 1.2K 0402 27 2 29 R18 1K 0603 28 24 23 A3V 30 VIDEO_DAC_B 31 13 14 VENC_HREF see JP3 VENC_VSYNC see JP3 4 L2 0.68UH 0805 15 L5 2.2UH 0805 J7 GND7 SCRESET/RTC GND8 TTX GND9 TTXREQ GND10 R17 75.0 0603 5 L8 0.68UH 0805 CON024 1 3 2 GND5 34 9 R14 1K 0603 RESET R39 100K 0603 3 R26 75.0 0603 DAC A U4 GND4 32 C28 330PF 0603 P0 3.3V 16 C18 330PF 0603 8 AD8061ARTZ SOT23-5 P4 BLANK AV_RESET R11 75.0 0603 CON024 AGND2 P7 HSYNC 27MHZ_CLK 2 A3V FER4 600 0603 R12 75.0 0603 DAC B 5 AD8061ARTZ SOT23-5 6 6 7 R16 75.0 0603 8 C31 330PF 0603 R28 75.0 0603 R19 1K 0603 1 9 11 C20 330PF 0603 R41 150.0 1206 12 D1 AD1580BRTZ SOT23D 2 10MA 17 19 AGND2 26 3 R23 1K 0603 40 ADV7179KCPZ LFCSP40 A3V R40 100K 0603 VIDEO_DAC_C U5 4 L3 0.68UH 0805 L6 2.2UH 0805 J7 L9 0.68UH 0805 1 3 2 3.3V C50 0.01UF 0603 C58 0.01UF 0603 C52 0.1UF 0603 A3V C57 0.1UF 0603 C49 0.1UF 0603 C53 0.1UF 0603 C30 0.1UF 0603 COPPER W1 A3V C29 0.01UF 0603 C33 0.1UF 0603 R21 75.0 0603 A3V C32 0.1UF 0603 C37 0.1UF 0603 C36 0.01UF 0603 C21 330PF 0603 C35 330PF 0603 R30 75.0 0603 AGND2 AGND2 AGND2 AD8061 AD8061 AD8061 2 3 Size Date B C 20 Cotton Road Nashua, NH 03063 4 PH: 1-800-ANALOGD BLACKFIN A-V EZ-EXTENDER VIDEO ENCODER (OUT) Board No. C A DAC C AD8061ARTZ SOT23-5 ANALOG DEVICES AGND2 Title AGND2 CON024 R24 1K 0603 4 ADV7179 U27 R22 75.0 0603 5 Rev A0193-2004 2.1 Sheet 07-06-2011_15:16 D 7 of 12 A B C D 3.3V 3.3V AVIN1 AVIN4 AVIN5 Composite Video CVBS CVBS CVBS Differential Component Video Y S Video Y V VIDEO DECODER U R10 10K 0603 C R34 10K 0603 DNP 1 1 OE OUT R45 10K 0603 R3 10K 0603 U2 27MHZ_CLK R5 33.0 0603 U1 R35 10K 0603 DNP 1 3 29 28 27MHZ OSC003 XTAL XTAL1 P15 P14 P13 66 67 SDA 68 SCL ALSB P12 SDA P11 SCLK P10 P9 64 AV_RESET 36 RESET P8 PWRDN P7 P6 J7 65 R15 0 0603 CON024 7 AVIN1 C19 0.1UF 0603 NC[ISO] P5 P4 VIDEO_AVIN1 42 41 AIN1 P3 AIN7 P2 9 P1 TP1 44 J7 43 R20 0 0603 CON024 4 AVIN4 C34 0.1UF 0603 AIN2 P0 VIDEO_AVIN4 46 45 2 AIN3 LLC2 AIN9 NC[LLCREF] 6 ELPF 58 J7 57 R25 0 0603 CON024 1 AVIN5 C22 0.1UF 0603 60 59 AIN10 AIN5 AIN11 3 HS FIELD NC[VREF] NC[HREF] R27 75.0 0603 R29 75.0 0603 TP3 R31 75.0 0603 62 61 CT3 10UF B C12 0.1UF 0603 CT2 10UF B C14 0.1UF 0603 AGND2 52 AIN12 NC[CLKIN] REFOUT CML SFL[HFF] NC[AEF] NC[DV] 48 49 AGND2 CT1 10UF B C8 0.1UF 0603 C9 1000PF 0603 54 55 CAPY1 NC[RD] CAPY2 OE CAPC1 NC[GPO3] CAPC2 NC[GPO2] NC[GPO1] C1 0.1UF 0603 3 NC[GPO0] C11 0.1UF 0603 CT4 10UF B C23 0.1UF 0603 C24 1000PF 0603 50 AVDD DVDD1 DVDD2 DVDD3 AGND2 38 AGND2 C15 0.1UF 0603 C38 0.1UF 0603 40 47 1.8V 3.3V 53 AGND2 PVDD DVDDIO1 DVDDIO2 39 AGND2 56 FER2 600 1206 63 VID_IN_D6 75 VID_IN_D5 76 VID_IN_D4 5 VID_IN_D3 6 VID_IN_D2 7 VID_IN_D1 8 VID_IN_D0 VID_IN_D[7:0] 19 R8 33.0 0603 20 R33 33.0 0603 U6 1 21 4 VDEC_CLKOUT 2 22 SN74LVC1G32 SOT23-5 23 24 PVDD_ADV7183 32 33 27 C2 0.01UF 0603 26 25 C5 .082UF 0805 R1 1.5K 0805 TP4 TP5 TP6 2 37 2 1 80 VDEC_HS see JP3 VDEC_VS see JP3 VDEC_FIELD 69 VDEC_VREF 70 VDEC_HREF AIN6 NC[AFF] 51 74 AIN4 VS VIDEO_AVIN5 VID_IN_D7 AIN8 LLC1 TP2 73 16 11 12 13 78 77 79 DEC_DATA_OE 17 18 34 1.8V 35 3.3V 3.3V 3.3V 1.8V DVDD_ADV7183 FER3 600 1206 3 30 VR1 10 R32 10K 0603 72 7 1 OUT1 8 2 OUT2 IN1 IN2 3 OUT3 4 6 SD 15 AGND1 AGND2 DGND1 AGND3 DGND2 AGND4 DGND3 AGND5 DGND4 NC[AGND6] DGND5 R38 76.8K 0805 5 FB C27 1UF 0603 GND 4 ADP3336ARMZ MSOP8 3 C39 1UF 0603 9 R36 147.0K 0805 14 31 71 ADV7183BKSTZ LQFP80 FER1 600 1206 3.3V 3.3V PVDD_ADV7183 3.3V DVDD_ADV7183 C4 0.1UF 0603 4 C17 0.1UF 0603 C41 0.01UF 0603 C40 0.1UF 0603 C13 0.1UF 0603 C16 0.01UF 0603 C25 0.01UF 0603 C26 0.1UF 0603 C43 0.1UF 0603 C3 0.01UF 0603 C7 0.1UF 0603 C6 0.01UF 0603 ANALOG DEVICES C10 0.1UF 0603 Title AGND2 Size 27MHZ OSC SN74LVC1G32 A Date B C Nashua, NH 03063 4 PH: 1-800-ANALOGD BLACKFIN A-V EZ-EXTENDER VIDEO DECODER (IN) Board No. C ADV7183 U28 20 Cotton Road Rev A0193-2004 2.1 Sheet 07-06-2011_15:16 D 8 of 12 A B C D I2S_EN I2S_EN 2 RFS0 U30 4 TFS0 R145 33.0 0603 1 1 U29 R144 33.0 0603 2 RSCLK0 SN74LVC1G125 SOT23-5 4 3.3V TSCLK0 SN74LVC1G125 SOT23-5 IN1 R60 10K 0603 1 R68 33.0 0603 U18 1 AUDIO CODEC 3.3V 5V R141 10K 0603 1 3 OUT OE AD1836_CLK OUT1 FER9 600 1206 5 6 R107 10K 0603 IN1 IDC3X2_SMT U24 3 Jumpers R142 33.0 0603 47 ASDATA1 3 ADC1_RIGHT 10 A5V115 A5V2 4 1 5V140 5V2 2 3 46 DR0SEC 1 J8 2 ADC1_LEFT 3V DR0PRI OUT3 A5V JP7 I2S_EN OUT2 12.288MHZ OSC003 3.3V 3.3V IN2 1 8 OUT1L+ 48 OUT1L+ 9 ASDATA2 OUT1L- OUT1L- DAC1 LEFT 4 DAC1_LEFT 7 44 RFS0 ALRCLK R143 10 0603 RSCLK0 OUT1 8 43 ABCLK 31 OUT1R+ OUT1R+ 30 OUT1R- OUT1R- DAC1 RIGHT 5 DAC1_RIGHT 6 45 AD1836_CLK MCLK 2 6 OUT2L+ 50 SNAPSHOT_FODD_SSEL OUT2L+ 7 CLATCH OUT2L- OUT2L- CON066 3.5MM DAC2 LEFT ADC2_LEFT 51 SCK 2 J9 2 CCLK 2 MOSI CDATA 49 MISO 33 OUT2R+ COUT OUT2R+ OUT2R- 32 OUT2R- DAC2 RIGHT IN2 3 ADC2_RIGHT 1 ADC1 LEFT 16 IN1L+ IN1L+ 17 IN1L- 4 OUT3L+ OUT3L+ 5 IN1L- OUT3L- OUT3L- DAC3 LEFT 4 DAC2_LEFT 7 8 ADC1 RIGHT 18 IN1R+ IN1R+ OUT3R+ 19 IN1R- IN1R- OUT3R- 20 IN2L+/CL2/CL2 DSDATA1 21 IN2L-/CL1/CL1 ADC2 LEFT DSDATA2 22 IN2L1 NC/IN2L1/IN2L+ DSDATA3 23 IN2L2 NC/IN2L2/IN2L- DLRCLK DBCLK ADC2 RIGHT 35 OUT3R+ 34 OUT3R- 38 41 NC/IN2R1/IN2R+ FILTR 26 IN2R-/CR1/CR1 FILTD CON066 3.5MM J10 2 DAC3_LEFT 42 TFS0 37 TSCLK0 NC/IN2R2/IN2R- 25 IN2R1 6 DT0SEC 36 R135 0 0603 13 2 3 4 12 1 7 CON_SJ-3523-SMT 3.5MM AD1836_VREF 6 IN2R+/CR2/CR2 AD8606ARZ SOIC8 AD1836AASZ MQFP52 11 14AGND1 28AGND2 29AGND3 AGND4 PD/RST 39 52GND1 GND2 3 OUT3 3 U27 5 27 JP10 1 IDC2X2 DAC3_RIGHT 3 AV_RESET OUT2 5 DAC2_RIGHT DT0PRI 24 IN2R2 DAC3 RIGHT CT12 10UF B C131 0.1UF 0603 CT13 10UF B C132 0.1UF 0603 3 AGND R130 0 0603 R111 0 0603 3 U27 1 C93 1000PF 0603 C100 1000PF 0603 C103 1000PF 0603 C111 1000PF 0603 2 AD8606ARZ SOIC8 R115 0 0603 AGND AGND 3.3V 4 3.3V C144 0.1UF 0603 3.3V C145 0.1UF 0603 3.3V C75 0.1UF 0603 5V C110 0.01UF 0603 C124 0.1UF 0603 A5V C99 0.1UF 0603 C115 0.1UF 0603 A5V C130 0.1UF 0603 W2 ANALOG DEVICES C120 0.22UF 0805 MSC_COPPER Title AGND SN74LVC1G125 SN74LVC1G125 12.288MHZ OSC AD1836 AGND Size AGND Date A B C Nashua, NH 03063 4 PH: 1-800-ANALOGD BLACKFIN A-V EZ-EXTENDER AUDIO Board No. C AD8606 20 Cotton Road Rev A0193-2004 2.1 Sheet 21-06-2011_10:31 D 9 of 12 A B C 1 1 C106 100PF 0603 R100 5.49K 0603 R93 11.0K 0603 D R92 3.32K 0603 OUT1R- C107 330PF 0603 2 U23 1 DAC1 RIGHT 3 R86 5.49K 0603 C89 680PF 0603 AD8606ARZ SOIC8 R85 1.65K 0603 R102 604.0 0603 OUT1R+ CT8 10UF CAP002 DAC1_RIGHT R79 2.74K 0603 C95 220PF 0603 C113 2200PF 0603 R109 49.9K 0603 2 2 AGND C105 100PF 0603 R99 5.49K 0603 R90 11.0K 0603 R91 3.32K 0603 OUT1L- C104 330PF 0603 6 U23 7 DAC1 LEFT 5 R83 5.49K 0603 C88 680PF 0603 AD8606ARZ SOIC8 R84 1.65K 0603 R104 604.0 0603 OUT1L+ 3 CT7 10UF CAP002 3 DAC1_LEFT R78 2.74K 0603 C94 220PF 0603 C116 2200PF 0603 AD1836_VREF R108 49.9K 0603 AGND A5V ANALOG DEVICES C112 0.22UF 0805 4 Title AGND Size AD8606 A B C Nashua, NH 03063 4 PH: 1-800-ANALOGD BLACKFIN A-V EZ-EXTENDER AUDIO OUT(CH1) Board No. C Date 20 Cotton Road Rev A0193-2004 2.1 Sheet 07-06-2011_15:16 D 10 of 12 A B C D 1 1 C136 100PF 0603 R132 5.49K 0603 R126 11.0K 0603 C109 100PF 0603 R101 5.49K 0603 R125 3.32K 0603 R94 11.0K 0603 OUT2R- R95 3.32K 0603 OUT3R- C137 330PF 0603 2 C108 330PF 0603 U25 1 DAC2 RIGHT 7 DAC3 RIGHT 3 R119 5.49K 0603 C123 680PF 0603 5 AD8606ARZ SOIC8 R118 1.65K 0603 U22 6 R133 604.0 0603 R87 5.49K 0603 CT15 10UF CAP002 OUT2R+ C90 680PF 0603 AD8606ARZ SOIC8 R88 1.65K 0603 R103 604.0 0603 OUT3R+ CT9 10UF CAP002 DAC2_RIGHT R113 2.74K 0603 C126 220PF 0603 C140 2200PF 0603 AD1836_VREF DAC3_RIGHT R80 2.74K 0603 R138 49.9K 0603 C96 220PF 0603 C114 2200PF 0603 R96 49.9K 0603 2 2 AGND C134 100PF 0603 R131 5.49K 0603 R123 11.0K 0603 AGND C97 100PF 0603 R89 5.49K 0603 R124 3.32K 0603 R82 11.0K 0603 OUT2L- R81 3.32K 0603 OUT3L- C133 330PF 0603 6 C98 330PF 0603 U25 7 DAC2 LEFT 1 DAC3 LEFT 5 3 R116 5.49K 0603 C122 680PF 0603 3 AD8606ARZ SOIC8 R117 1.65K 0603 U22 2 R136 604.0 0603 OUT2L+ R75 5.49K 0603 CT14 10UF CAP002 C84 680PF 0603 AD8606ARZ SOIC8 R74 1.65K 0603 3 R98 604.0 0603 OUT3L+ CT10 10UF CAP002 DAC2_LEFT R112 2.74K 0603 C125 220PF 0603 C142 2200PF 0603 DAC3_LEFT R71 2.74K 0603 R137 49.9K 0603 C87 220PF 0603 C102 2200PF 0603 AGND AGND A5V 4 A5V C135 0.22UF 0805 ANALOG DEVICES C101 0.22UF 0805 Title Size A R97 49.9K 0603 AGND AGND AD8606 AD8606 B C Nashua, NH 03063 4 PH: 1-800-ANALOGD BLACKFIN A-V EZ-EXTENDER AUDIO OUT(CH2, CH3) Board No. C Date 20 Cotton Road Rev A0193-2004 2.1 Sheet 07-06-2011_15:16 D 11 of 12 A B CT6 10UF CAP002 FER6 600 0603 1 R77 5.76K 0603 C R73 5.76K 0603 D CT5 10UF CAP002 FER5 600 0603 ADC1_LEFT R76 5.76K 0603 R61 5.76K 0603 ADC2_LEFT 1 C83 120PF 0603 C92 100PF 0603 C91 100PF 0603 R70 237.0 0603 U21 2 C71 120PF 0603 2 1 1 IN1L- AGND IN2L2 AGND 3 3 AD8606ARZ SOIC8 R63 5.76K 0603 AD8606ARZ SOIC8 C86 1000PF 0603 R62 5.76K 0603 C77 100PF 0603 R67 5.76K 0603 R72 5.76K 0603 ADC1 LEFT C74 120PF 0603 C72 1000PF 0603 R69 750.0K 0603 R64 237.0 0603 U21 6 ADC2 LEFT C82 120PF 0603 AGND R65 750.0K 0603 6 7 U20 7 IN1L+ 5 IN2L1 5 AD8606ARZ SOIC8 2 U20 AD8606ARZ SOIC8 2 AGND AGND CT11 10UF CAP002 FER7 600 0603 R122 5.76K 0603 R121 5.76K 0603 CT16 10UF CAP002 FER8 600 0603 ADC1_RIGHT R140 5.76K 0603 R134 5.76K 0603 ADC2_RIGHT C128 120PF 0603 C129 100PF 0603 R106 237.0 0603 U26 6 C141 120PF 0603 C139 100PF 0603 7 1 IN1R- AGND IN2R2 AGND 5 3 AD8606ARZ SOIC8 R105 5.76K 0603 3 U28 2 AD8606ARZ SOIC8 C119 1000PF 0603 R120 5.76K 0603 C118 100PF 0603 R128 5.76K 0603 R139 5.76K 0603 ADC1 RIGHT AGND C117 1000PF 0603 R129 750.0K 0603 R110 237.0 0603 U26 2 1 ADC2 RIGHT C143 120PF 0603 C127 120PF 0603 R127 750.0K 0603 3 U28 6 7 IN1R+ 3 IN2R1 5 AD8606ARZ SOIC8 AD8606ARZ SOIC8 AGND AGND AD1836_VREF A5V A5V C73 0.22UF 0805 4 A5V C121 0.22UF 0805 A5V C138 0.22UF 0805 ANALOG DEVICES C85 0.22UF 0805 Title AGND AGND AGND AGND Size AD8606 AD8606 AD8606 AD8606 C Date A B C 20 Cotton Road Nashua, NH 03063 4 PH: 1-800-ANALOGD BLACKFIN A-V EZ-EXTENDER AUDIO IN(CH1, CH2) Board No. Rev A0193-2004 2.1 Sheet 10-06-2011_09:57 D 12 of 12 I INDEX Numerics 2-wire interface (TWI) signals, 1-4, 2-5 source selection jumpers, 2-8 A AD1836A audio codecs, 2-5, 2-6, 2-10, 2-13 ADSP-BF533/37/61 processors flag pins, 2-5, 2-9, 2-14 parallel peripheral interfaces (PPI0-1), 1-2, 1-4, 1-6, 2-4 serial peripheral interface (SPI), 1-3 SPORT signals, 2-13 ADV7179 video encoders connections, 1-4 HREF connect jumper, 2-10 VSYNC connect jumper, 2-10 ADV7183B video decoders connections, 1-4 HSYNC disconnect jumper, 2-9 output enable jumper, 2-10 VSYNC connect jumper, 2-9 Blackfin A-V EZ-Extender Manual analog audio interface, See audio interface video interface, See video interface architecture, of this EZ-Extender, 2-2 ASDATA1-2 (AD1836A output) pins, 2-13 audio codecs, See AD1836A audio codecs interface, x, 1-3, 2-2 loopback jumpers, 2-15 AV_RESET source jumper, 2-14 B bidirectional buffers, 2-2 bill of materials, A-1 block diagram, of AV EZ-Extender, 2-3 board schematic (Blackfin AV EZ-Extender), B-1 C camera module interfaces, 1-4, 2-11 connectors DB9, 1-6 J4 (OmniVision camera), 1-5 I-1 Index D H data clock, 2-2 pins, See PPI0_Dx, PPI1_Dx DB9 connector, 1-6 DR0PRI net, 2-6 DR0SEC net, 2-6 DT0PRI net, 2-6 DT0SEC net, 2-6 Dx pins, 2-5 HREF connection jumper, 2-10 signal, 2-4 HS signal, 2-4, 2-5 HSYNC disconnect jumper, 2-9 signal, 2-4 E example programs, 1-7 expansion interface, 1-3, 1-4, 2-4 EXT_VID_CLK net, 2-11 I I2S mode, 1-3, 2-6, 2-13 installation, of Blackfin AV EZ-Extender, 1-2 interfaces, See audio interface, video interface, flat panel display interface, camera module interfaces F flag pins, ADSP-BF533/37/61 processors, 2-5, 2-9, 2-14 FLAG_SCL_DIR_CTRL net, 2-5 FLAG_SDA net, 2-5 flat panel display interface, See FPDI FODD (OmniVision control) signal, 2-10 FPDI connections, xi, 1-6, 2-2 HS signal, 2-4, 2-5 VS signal, 2-4, 2-5 frame sync signals, 2-2, 2-14 G general-purpose flags, 2-10, 2-12, 2-13, 2-15 I-2 J JP10.1/2 (audio loop-back) jumper, 2-15 JP10.3/4 (audio loop-back) jumper, 2-15 JP1.1/2 (video loop-back) jumper, 2-8 JP1.3/4 (video loop-back) jumper, 2-8 JP1.5/6 (video loop-back) jumper, 2-8 JP2 (voltage select) jumper, 2-8 JP3.11/12 (ADV7183B HSYNC disconnect) jumper, 2-9 JP3.13/14 (ADV7183B VSYNC connect) jumper, 2-9 JP3.15/16 (ADV7179 HREF connect) jumper, 2-10 JP3.17/18 (ADV7179 VSYNC connect) jumper, 2-10 JP3.19/20 (ADV7183B enable) jumper, 2-10 JP3.21/22 (SNAPSHOT_FODD) jumper, 2-5, 2-10 JP3.3/5/7 (TWI source) jumper, 2-4, 2-5, 2-8 Blackfin A-V EZ-Extender Manual Index JP3.4/6/8 (TWI source) jumper, 2-4, 2-5, 2-8 JP3.9/10 (PDWN connect) jumper, 2-4, 2-5, 2-9 JP4.1/2 (PPI clock) jumper, 2-4, 2-5, 2-11 JP4.3/4 (PPI clock) jumper, 2-4, 2-5, 2-11 JP4.5/6 (PPI clock) jumper, 2-4, 2-5, 2-11 JP4.7/8 (PPI clock) jumper, 2-4, 2-5, 2-11 JP5.1/2 (PPI0 data enable) jumper, 2-11 JP5.3/4 (video out control) jumper, 2-4, 2-5, 2-12 JP5.5/6 (video out control) jumper, 2-4, 2-5, 2-12 JP6.1/3/5 (PPIO_SYNC1 direct) jumper, 2-4, 2-12 JP6.2/4/6 (PPI0_SYNC2 direct) jumper, 2-4, 2-13 JP7.1/2 (I2S enable) jumper, 1-3, 2-6, 2-13 JP7.3/4 (SPORT connect) jumper, 2-6, 2-13 JP7.5/6 (SPORT connect) jumper, 2-6, 2-13 JP8.1/3/5 (video out SYNC select) jumper, 2-4, 2-5, 2-14 JP8.2/4/6 (video out SYNC select) jumper, 2-4, 2-5, 2-14 JP8.7/8 (video out SYNC enable) jumper, 2-4, 2-5, 2-14 JP9.1/3/5 (reset) jumper, 2-14 JP9.2/4/6 (PPI0 direction) jumper, 2-4, 2-15 jumpers See also jumpers by name (JPx) map of locations, 2-7 K Kodak camera interface, xi, 2-5, 2-9 connector (P4), 1-5 SNAPSHOT signal, 2-10 Blackfin A-V EZ-Extender Manual M Micron camera interface, xi connector (J6), 1-5 MISO net, 2-6 MOSI net, 2-6 multibit sigma-delta architecture, 1-3 O OmniVision camera interface, x, 1-5, 2-5, 2-9 connector (J4), 1-5 control signal (FODD), 2-10 P parallel peripheral interfaces See also PPI0, PPI1, ADSP-BF533/37/61 processors audio module connections, 1-4 camera module connections, 1-6 clock setup jumpers, 2-11 driving VID_OUT bus, 2-12, 2-14 of ADSP-BF533/37/61 EZ-KIT Lites, 2-2 PDWN connect jumper, 2-9 input signal, 2-5 PIXEL_CLK net, 2-11 PPI0 data bus enable jumper, 2-11 data direction setup jumper, 2-15 frame SYNC signals, 2-9 PPI0_CLK net, 2-4, 2-11 PPI0_Dx nets, 2-4, 2-15 PPI0_SYNC1-2 direction setup jumpers, 2-12, 2-13 nets, 2-4 PPI1_CLK net, 2-5, 2-11 PPI1_Dx nets, 1-3, 2-4, 2-5, 2-14 I-3 Index PPI1_FS1-2 nets, 2-5 product overview, x R RCA phono jacks, x reset, 1-3 AD1836A, 1-3 RFS0 net, 2-6 RSCLK0 net, 2-6 S schematic, of Blackfin AV EZ-Extender, B-1 SCK net, 2-5 serial peripheral interface, See SPI setup, of this EZ-Extender, 1-2 SNAPSHOT_FODD disconnect jumper, 2-10 SNAPSHOT_FODD_SSEL net, 2-5 SNAPSHOT (Kodak camera) signal, 2-10 SPI serial clock (SCK), 2-5 serial input data signal (MISO), 2-6 serial output data signal (MOSI), 2-6 SPORT configuring for I2S mode, 2-13 data connect jumpers, 2-13 SPORT0 connections, 1-3, 2-2 receive clock signal (RSCLK0), 2-6 receive frame SYNC signal (RFS0), 2-6 transmit clock signal (TSCLK0), 2-6 transmit frame SYNC signal (TFS0), 2-6 I-4 system architecture, of Blackfin AV EZ-Extender, 2-2 reset, 2-14 T technical support, xiii TFS0 net, 2-6 time-division multiplexed (TDM) mode, 1-3 TSCLK0 net, 2-6 U unidirectional buffers, 2-2 V VDEC_CLKOUT net, 2-11 video interface, 1-4, 2-2, 2-4, 2-5 decoders, See ADV7183B video decoders encoders, See ADV7179 video encoders test loopback jumpers, 2-8 VID_IN bus, 2-2, 2-4, 2-10 VID_OUT bus control jumpers, 2-12 signals, 2-2, 2-4 SYNC enable jumper, 2-14 SYNC source select jumpers, 2-14 voltage selection jumper, 2-8 VS signal, 2-4, 2-5 VSYNC connect jumper, 2-9, 2-10 Blackfin A-V EZ-Extender Manual Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Analog Devices Inc.: ADZS-BFAV-EZEXT