M MCP6021/2/3/4 Rail-to-Rail Input/Output, 10 MHz Op Amps Features Description * * * * The MCP6021, MCP6022, MCP6023 and MCP6024 from Microchip Technology Inc. are rail-to-rail input and output op amps with high performance. Key specifications include: wide bandwidth (10 MHz), low noise (8.7 nV/Hz), low input offset voltage and low distortion (0.00053% THD+N). These features make these op amps well suited for applications requiring high performance and bandwidth. The MCP6023 also offers a chip select pin (CS) that gives power savings when the part is not in use. * * * * * * Rail-to-Rail Input/Output Wide Bandwidth: 10 MHz (typ.) Low Noise: 8.7 nV/Hz, at 10 kHz (typ.) Low Offset Voltage: - Industrial Temperature: 500 V (max.) - Extended Temperature: 250 V (max.) Mid-Supply V REF: MCP6021 and MCP6023 Low Supply Current: 1 mA (typ.) Total Harmonic Distortion: 0.00053% (typ., G = 1) Unity Gain Stable Power Supply Range: 2.5V to 5.5V Temperature Range: - Industrial: -40C to +85C - Extended: -40C to +125C The single MCP6021, single MCP6023 and dual MCP6022 are available in standard 8-lead PDIP, SOIC and TSSOP. The quad MCP6024 is offered in 14-lead PDIP, SOIC and TSSOP packages. The MCP6021/2/3/4 family is available in the Industrial and Extended temperature ranges. It has a power supply range of 2.5V to 5.5V. Typical Applications * * * * * * * * * Automotive Driving A/D Converters Multi-Pole Active Filters Barcode Scanners Audio Processing Communications DAC Buffer Test Equipment Medical Instrumentation Available Tools * SPICE Macro Model (at www.microchip.com) * FilterLab(R) software (at www.microchip.com) PACKAGE TYPES MCP6021 PDIP SOIC, TSSOP NC 1 VIN- 2 VIN+ 3 VSS 4 MCP6022 PDIP SOIC, TSSOP 8 NC VOUTA 1 7 VDD VINA- 2 6 VOUT VINA+ 3 5 VREF 2003 Microchip Technology Inc. VSS 4 MCP6023 PDIP SOIC, TSSOP NC 1 8 VDD V IN- 2 7 VOUTB 6 VINB- VIN+ 3 5 V + VSS 4 INB MCP6024 PDIP SOIC, TSSOP 8 CS 7 VDD VOUTA 1 VINA- 2 14 VOUTD 13 VIND- 6 VOUT VINA+ 3 VDD 4 12 VIND+ 11 VSS VINB+ 5 VINB- 6 VOUTB 7 10 VINC+ 9 VINC- 5 VREF 8 VOUTC DS21685B-page 1 MCP6021/2/3/4 1.0 ELECTRICAL CHARACTERISTICS Pin Function Table Name Absolute Maximum Ratings VDD - VSS .........................................................................7.0V All Inputs and Outputs ..................... VSS - 0.3V to V DD + 0.3V Difference Input Voltage ....................................... |VDD - VSS| Output Short Circuit Current ..................................continuous Current at Input Pins ....................................................2 mA Current at Output and Supply Pins ............................30 mA Storage Temperature ....................................-65C to +150C Junction Temperature.................................................. +150C ESD Protection on all pins (HBM/MM) ................ 2 kV / 200V Notice: Stresses above those listed under "Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operational listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. Function VIN +, VINA+, VINB+, VINC+, VIND+ Non-inverting Inputs VIN -, VINA-, VINB-, VINC-, VIND- Inverting Inputs VDD Positive Power Supply VSS Negative Power Supply CS Chip Select VREF Reference Voltage VOUT, VOUTA, VOUTB, VOUTC , VOUTD Outputs NC No Internal Connection DC CHARACTERISTICS Electrical Specifications: Unless otherwise indicated, TA = +25C, VDD = +2.5V to +5.5V, VSS = GND, VCM = VDD/2, VOUT VDD/2 and R L = 10 k to VDD/2. Parameters Sym Min Typ Max Units Conditions Industrial Temperature Parts VOS -500 -- +500 V VCM = 0V Extended Temperature Parts VOS -250 -- +250 V VCM = 0V, VDD = 5.0V Extended Temperature Parts VOS -2.5 -- +2.5 mV VCM = 0V, VDD = 5.0V TA = -40C to +125C Input Offset Voltage Temperature Drift VOS/TA -- 3.5 -- PSRR 74 90 -- IB -- 1 -- pA IB -- 30 150 pA TA = +85C TA = +125C Input Offset Input Offset Voltage: Power Supply Rejection Ratio V/C TA = -40C to +125C dB VCM = 0V Input Current and Impedance Input Bias Current Industrial Temperature Parts IB -- 640 5,000 pA Input Offset Current IOS -- 1 -- pA Common-Mode Input Impedance ZCM -- 1013||6 -- ||pF Differential Input Impedance ZDIFF -- 1013||3 -- ||pF Common-Mode Input Range VCMR VSS-0.3 -- VDD +0.3 V Common-Mode Rejection Ratio CMRR 74 90 -- dB VDD = 5V, VCM = -0.3V to 5.3V CMRR 70 85 -- dB VDD = 5V, VCM = 3.0V to 5.3V CMRR 74 90 -- dB VDD = 5V, VCM = -0.3V to 3.0V Extended Temperature Parts Common-Mode Voltage Reference (MCP6021 and MCP6023 only) VREF Accuracy (VREF - VDD /2) VREF Temperature Drift VREF -50 -- +50 VREF /T -- 100 -- 90 110 -- mV V/C TA = -40C to +125C A Open Loop Gain DC Open Loop Gain (Large Signal) DS21685B-page 2 AOL dB VCM = 0V, VOUT = VSS+0.3V to VDD -0.3V 2003 Microchip Technology Inc. MCP6021/2/3/4 DC CHARACTERISTICS (CONTINUED) Electrical Specifications: Unless otherwise indicated, TA = +25C, VDD = +2.5V to +5.5V, VSS = GND, VCM = VDD/2, VOUT VDD/2 and R L = 10 k to VDD/2. Parameters Sym Min Typ Max Units V OL, VOH ISC VSS+15 -- VDD -20 mV -- 30 -- mA Supply Voltage VS 2.5 -- 5.5 V Quiescent Current per Amplifier IQ 0.5 1.0 1.35 mA Conditions Output Maximum Output Voltage Swing Output Short Circuit Current 0.5V output overdrive Power Supply IO = 0 AC CHARACTERISTICS Electrical Specifications: Unless otherwise indicated, TA = 25C, VDD = +2.5V to +5.5V, VSS = GND, V CM = VDD/2, VOUT VDD /2, RL = 10 k to VDD/2 and CL = 60 pF. Parameters Sym Min Typ Max Units GBWP -- 10 -- MHz PM -- 65 -- tSETTLE -- 250 -- ns SR -- 7.0 -- V/s Conditions AC Response Gain Bandwidth Product Phase Margin at Unity-Gain Settling Time, 0.2% Slew Rate G=1 G = 1, VOUT = 100 mVp-p Total Harmonic Distortion Plus Noise f = 1 kHz, G = 1 THD+N -- 0.00053 -- % VOUT = 0.25V + 3.25V, BW = 22 kHz f = 1 kHz, G = 1, RL = 600@1 KHz THD+N -- 0.00064 -- % VOUT = 0.25V + 3.25V, BW = 22 kHz f = 1 kHz, G = +1 V/V THD+N -- 0.0014 -- % VOUT = 4VP-P, VDD = 5.0V, BW = 22 kHz f = 1 kHz, G = +10 V/V THD+N -- 0.0009 -- % VOUT = 4VP-P, VDD = 5.0V, BW = 22 kHz f = 1 kHz, G = +100 V/V THD+N -- 0.005 -- % VOUT = 4VP-P, VDD = 5.0V, BW = 22 kHz Input Voltage Noise Eni -- 2.9 -- Vp-p f = 0.1 Hz to 10 Hz Input Voltage Noise Density eni -- 8.7 -- nV/Hz f = 10 kHz Input Current Noise Density ini -- 3 -- fA/Hz f = 1 kHz Noise MCP6023 CHIP SELECT (CS) CHARACTERISTICS Electrical Specifications: Unless otherwise indicated, TA = 25C, VDD = +2.5V to +5.5V, VSS = GND, VCM = VDD/2, VOUT VDD/2, RL = 10 k to VDD/2 and CL = 60 pF. Parameters Sym Min Typ Max Units CS Logic Threshold, Low VIL 0 -- 0.2VDD V CS Input Current, Low ICSL -1.0 0.01 -- A CS Logic Threshold, High VIH 0.8VDD -- VDD V CS Input Current, High Conditions DC Characteristics CS = VSS ICSH -- 0.01 2.0 A CS = VDD CS Input High, GND Current ISS -- 0.05 2.0 A CS = VDD Amplifier Output Leakage -- -- 0.01 -- A CS = VDD CS Low to Amplifier Output Turn-on Time tON -- 2 10 s G = 1, VIN = VSS, CS = 0.2VDD to VOUT = 0.45VDD time CS High to Amplifier Output High-Z Turn-off Time tOFF -- 0.01 -- s G = 1, VIN = VSS, CS = 0.8VDD to VOUT = 0.05VDD time VHYST -- 0.6 -- V Internal Switch Timing Hysteresis 2003 Microchip Technology Inc. DS21685B-page 3 MCP6021/2/3/4 TEMPERATURE CHARACTERISTICS Electrical Specifications: Unless otherwise indicated, V DD = +2.5V to +5.5V and V SS = GND. Parameters Symbol Min Typ Max Units TA -40 -- +85 C Extended Temperature Range TA -40 -- +125 C Operating Temperature Range TA -40 -- +125 C Storage Temperature Range TA -65 -- +150 C Conditions Temperature Ranges Industrial Temperature Range Note 1 Thermal Package Resistances Thermal Resistance, 8L-PDIP JA -- 85 -- C/W Thermal Resistance, 8L-SOIC JA -- 163 -- C/W Thermal Resistance, 8L-TSSOP JA -- 124 -- C/W Thermal Resistance, 14L-PDIP JA -- 70 -- C/W Thermal Resistance, 14L-SOIC JA -- 120 -- C/W Thermal Resistance, 14L-TSSOP JA -- 100 -- C/W Note 1: The industrial temperature devices operate over this extended temperature range, but with reduced performance. In any case, the internal junction temperature (TJ) must not exceed the absolute maximum specification of 150C. CS tON VOUT Hi-Z ISS 50 nA (typ.) ICS 10 nA (typ.) tOFF Amplifier On Hi-Z 1 mA (typ.) 50 nA (typ.) 10 nA (typ.) 10 nA (typ.) FIGURE 1-1: Timing diagram for the CS pin on the MCP6023. DS21685B-page 4 2003 Microchip Technology Inc. MCP6021/2/3/4 2.0 TYPICAL PERFORMANCE CURVES Note: The graphs and tables provided following this note are a statistical summary based on a limited number of samples and are provided for informational purposes only. The performance characteristics listed herein are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified operating range (e.g., outside specified power supply range) and therefore outside the warranted range. Input Offset Voltage (V) FIGURE 2-3: Input Offset Voltage vs. Common Mode Input Voltage with VDD = 2.5V. 12 8 10 6 20 16 12 8 0 6.0 5.5 5.0 4.5 4.0 3.5 3.0 2.5 2.0 -40C +25C +85C +125C 1.5 1.0 0.5 VDD = 5.5V 0.0 Input Offset Voltage (V) Input Offset Voltage (V) 3.0 500 400 300 200 100 0 -100 -200 -300 -400 -500 -0.5 2.5 Common Mode Input Voltage (V) 2003 Microchip Technology Inc. -4 FIGURE 2-5: Input Offset Voltage Drift, (Extended Temperature Parts). -40C +25C +85C +125C 2.0 -8 Input Offset Voltage Drift (V/C) FIGURE 2-2: Input Offset Voltage, (Extended Temperature Parts). 1.5 -12 -16 Input Offset Voltage (V) 1.0 438 Samples VCM = 0V TA = -40C to +125C E-Temp Parts 4 26% 24% 22% 20% 18% 16% 14% 12% 10% 8% 6% 4% 2% 0% -20 200 160 120 80 40 0 -40 Percentage of Occurances FIGURE 2-4: Input Offset Voltage Drift, (Industrial Temperature Parts). E-Temp Parts -80 -120 -160 -200 Percentage of Occurances 438 Samples VDD = 5.0V VCM = 0V TA = +25C 500 400 VDD = 2.5V 300 200 100 0 -100 -200 -300 -400 -500 -0.5 0.0 0.5 4 Input Offset Voltage Drift (V/C) FIGURE 2-1: Input Offset Voltage, (Industrial Temperature Parts). 24% 22% 20% 18% 16% 14% 12% 10% 8% 6% 4% 2% 0% 2 500 400 300 200 100 0 -100 -200 -300 -400 0% 0 2% -2 4% I-Temp Parts -4 6% -6 8% 1192 Samples TA = -40C to +85C -8 10% 12% 11% 10% 9% 8% 7% 6% 5% 4% 3% 2% 1% 0% -10 12% I-Temp Parts -12 14% 1192 Samples TA = +25C Percentage of Occurances 16% -500 Percentage of Occurances Note: Unless otherwise indicated, TA = +25C, VDD = +2.5V to +5.5V, VSS = GND, VCM = VDD/2, RL = 10 k to V DD/2, VOUT VDD/2 and C L = 60 pF. Common Mode Input Voltage (V) FIGURE 2-6: Input Offset Voltage vs. Common Mode Input Voltage with VDD = 5.5V. DS21685B-page 5 MCP6021/2/3/4 Note: Unless otherwise indicated, TA = +25C, VDD = +2.5V to +5.5V, VSS = GND, VCM = VDD/2, RL = 10 k to V DD/2, VOUT VDD/2 and C L = 60 pF. 200 Input Offset Voltage (V) 50 0 -50 -100 -150 -200 VDD = 5.0V VCM = 0V -250 VDD = 5.5V 50 0 VDD = 2.5V -50 -100 -150 Output Voltage (V) FIGURE 2-10: Output Voltage. 1.E+00 1.E+01 1 10 FIGURE 2-8: vs. Frequency. 1.E+02 1.E+03 1.E+04 100 1k 10k Frequency (Hz) 1.E+05 8 6 4 2 1.E+06 100k 1M 0 5.0 1.E-01 0.1 10 4.5 1 12 4.0 10 f = 1 kHz VDD = 5.0V 14 3.5 100 16 0.0 Input Noise Voltage Density (nV/Hz) 1,000 Input Offset Voltage vs. 3.0 Input Offset Voltage vs. 2.5 FIGURE 2-7: Temperature. 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 125 2.0 0 25 50 75 100 Ambient Temperature (C) 1.5 -25 1.0 -50 Input Noise Voltage Density (nV/Hz) 100 -200 -300 Common Mode Input Voltage (V) Input Noise Voltage Density FIGURE 2-11: Input Noise Voltage Density vs. Common Mode Input Voltage. 100 110 PSRR+ PSRR- 105 PSRR, CMRR (dB) 90 CMRR, PSRR (dB) VCM = VDD/2 150 0.5 Input Offset Voltage (V) 100 80 70 60 CMRR 50 40 CMRR 100 95 90 PSRR (VCM = 0V) 85 80 75 30 20 100 1.E+02 70 1.E+03 1k 1.E+04 10k 1.E+05 100k Frequency (Hz) FIGURE 2-9: Common Mode, Power Supply Rejection Ratios vs. Frequency. DS21685B-page 6 1.E+06 1M -50 -25 0 25 50 75 100 125 Ambient Temperature (C) FIGURE 2-12: Common Mode, Power Supply Rejection Ratios vs. Temperature. 2003 Microchip Technology Inc. MCP6021/2/3/4 IB, TA = +125C VDD = 5.5V 1,000 IOS, TA = +125C IB, TA = +85C 100 10 IOS, TA = +85C 1 10,000 VCM = VDD VDD = 5.5V 1,000 IB 100 IOS 10 1 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 25 35 45 55 65 75 85 95 105 115 125 Common Mode Input Voltage (V) Ambient Temperature (C) 1.2 1.1 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 +125C +85C +25C -40C FIGURE 2-16: vs. Temperature. 1.2 1.1 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 VDD = 5.5V VDD = 2.5V VCM = VDD - 0.5V -50 -25 FIGURE 2-17: Temperature. 35 30 25 20 15 10 5 +125C +85C +25C -40C 0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 Open-Loop Gain (dB) Output Short Circuit Current (mA) Quiescent Current vs. 120 110 100 90 80 70 60 50 40 30 20 10 0 -10 -20 1.E+00 1 2003 Microchip Technology Inc. 25 50 75 100 125 1.E+01 Quiescent Current vs. 1.E+02 1.E+03 10 100 1k 0 -15 -30 -45 -60 -75 Phase -90 -105 -120 -135 -150 Gain -165 -180 -195 -210 10k 100k 1M 10M 100M 1.E+04 1.E+05 1.E+06 1.E+07 1.E+08 Frequency (Hz) Supply Voltage (V) FIGURE 2-15: Output Short-Circuit Current vs. Supply Voltage. 0 Ambient Temperature (C) Power Supply Voltage (V) FIGURE 2-14: Supply Voltage. Input Bias, Offset Currents Open-Loop Phase () FIGURE 2-13: Input Bias, Offset Currents vs. Common Mode Input Voltage. Quiescent Current (mA/amplifier) Input Bias, Offset Currents (pA) 10,000 Quiescent Current (mA/amplifier) Input Bias, Offset Currents (pA) Note: Unless otherwise indicated, TA = +25C, VDD = +2.5V to +5.5V, VSS = GND, VCM = VDD/2, RL = 10 k to V DD/2, VOUT VDD/2 and C L = 60 pF. FIGURE 2-18: Frequency. Open-Loop Gain, Phase vs. DS21685B-page 7 MCP6021/2/3/4 Note: Unless otherwise indicated, TA = +25C, VDD = +2.5V to +5.5V, VSS = GND, VCM = VDD/2, RL = 10 k to V DD/2, VOUT VDD/2 and C L = 60 pF. 120 VDD = 5.5V DC Open-Loop Gain (dB) 120 110 VDD = 2.5V 100 90 115 VDD = 5.5V 110 105 VDD = 2.5V 100 95 90 1.E+02 1.E+03 1.E+04 1k 10k 1.E+05 -50 100k -25 Load Resistance (:) DC Open-Loop Gain vs. FIGURE 2-22: Temperature. VCM = VDD/2 110 VDD = 5.5V 100 90 VDD = 2.5V 80 70 0.00 0.05 0.10 0.15 0.20 0.25 50 75 100 -50 -25 0 25 50 75 75 8 60 Phase Margin, G = +1 6 4 45 30 2 15 VDD = 5.0V 0 FIGURE 2-23: Gain Bandwidth Product, Phase Margin vs. Common Mode Input Voltage. FIGURE 2-21: Gain Bandwidth Product, Phase Margin vs. Temperature. Gain Bandwidth Product (MHz) 14 Ambient Temperature (C) DS21685B-page 8 10 90 Common Mode Input Voltage (V) Phase Margin, G = +1 () GBWP, VDD = 5.5V GBWP, VDD = 2.5V PM, VDD = 2.5V PM, VDD = 5.5V 100 90 80 70 60 50 40 30 20 10 0 100 125 105 Gain Bandwidth Product 12 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 FIGURE 2-20: Small Signal DC Open-Loop Gain vs. Output Voltage Headroom. 10 9 8 7 6 5 4 3 2 1 0 125 DC Open-Loop Gain vs. 0 0.30 Output Voltage Headroom (V); VDD - VOH or VOL - VSS Gain Bandwidth Product (MHz) 25 14 120 Gain Bandwidth Product (MHz) DC Open-Loop Gain (dB) FIGURE 2-19: Load Resistance. 0 Ambient Temperature (C) Phase Margin, G = +1 () 80 100 12 105 Gain Bandwidth Product 10 75 8 Phase Margin, G = +1 6 60 45 4 2 90 30 VDD = 5.0V VCM = VDD/2 15 0 Phase Margin, G = +1 () DC Open-Loop Gain (dB) 130 0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 Output Voltage (V) FIGURE 2-24: Gain Bandwidth Product, Phase Margin vs. Output Voltage. 2003 Microchip Technology Inc. MCP6021/2/3/4 11 10 9 8 7 6 5 4 3 2 1 0 10 Falling, VDD = 5.5V Rising, VDD = 5.5V Maximum Output Voltage Swing (VP-P) Slew Rate (V/s) Note: Unless otherwise indicated, TA = +25C, VDD = +2.5V to +5.5V, VSS = GND, VCM = VDD/2, RL = 10 k to V DD/2, VOUT VDD/2 and C L = 60 pF. Falling, VDD = 2.5V Rising, VDD = 2.5V VDD = 5.5V VDD = 2.5V 1 0.1 10k 1.E+04 -50 -25 0 25 50 75 100 125 1.E+05 Ambient Temperature (C) FIGURE 2-25: Slew Rate vs. Temperature. 0.1000% f = 1 kHz BWMeas = 22 kHz VDD = 5.0V G = +100 V/V G = +100 V/V 0.0100% 1.E+07 10M FIGURE 2-28: Maximum Output Voltage Swing vs. Frequency. THD+N (%) THD+N (%) 0.1000% 1.E+06 100k 1M Frequency (Hz) G = +10 V/V 0.0010% 0.0100% G = +10 V/V 0.0010% G = +1 V/V f = 20 kHz BWMeas = 80 kHz VDD = 5.0V G = +1 V/V 0.0001% 0.0001% 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 Output Voltage (VP-P) 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 FIGURE 2-26: Total Harmonic Distortion plus Noise vs. Output Voltage with f = 1 kHz. FIGURE 2-29: Total Harmonic Distortion plus Noise vs. Output Voltage with f = 20 kHz. Channel to Channel Separation (dB) 6 Input, Output Voltage (V) VIN VDD = 5V G = +1 V/V 5 VOUT 4 3 2 1 0 -1 0.0E+00 1.0E-05 2.0E-05 3.0E-05 4.0E-05 5.0E-05 6.0E-05 7.0E-05 8.0E-05 9.0E-05 1.0E-04 Time (10 s/div) FIGURE 2-27: The MCP6021/2/3/4 family shows no phase reversal under overdrive. 2003 Microchip Technology Inc. Output Voltage (VP-P) 135 130 125 120 115 110 G = +1 V/V 105 1.E+03 1k 1.E+04 1.E+05 10k 100k Frequency (Hz) 1.E+06 1M FIGURE 2-30: Channel-to-Channel Separation vs. Frequency (MCP6022 and MCP6024 only). DS21685B-page 9 MCP6021/2/3/4 Note: Unless otherwise indicated, TA = +25C, VDD = +2.5V to +5.5V, VSS = GND, VCM = VDD/2, RL = 10 k to V DD/2, VOUT VDD/2 and C L = 60 pF. Output Voltage Headroom VDD-VOH or VOL-VSS (mV) Output Voltage Headroom; VDD-VOH or VOL-VSS (mV) 1,000 100 VOL - VSS 10 VDD - VOH 1 0.01 0.1 1 10 9 8 7 6 5 4 3 2 1 0 10 VOL - VSS VDD - VOH -50 -25 Output Current Magnitude (mA) FIGURE 2-31: Output Voltage Headroom vs. Output Current. FIGURE 2-34: vs. Temperature. 6.E-02 50 75 100 125 Output Voltage Headroom G = -1 V/V RF = 1 k: 5.E-02 Output Voltage (10 mV/div) Output Voltage (10 mV/div) 25 6.E-02 G = +1 V/V 5.E-02 4.E-02 3.E-02 2.E-02 1.E-02 0.E+00 -1.E-02 -2.E-02 -3.E-02 -4.E-02 4.E-02 3.E-02 2.E-02 1.E-02 0.E+00 -1.E-02 -2.E-02 -3.E-02 -4.E-02 -5.E-02 -5.E-02 -6.E-02 -6.E-02 0.E+00 2.E-07 4.E-07 6.E-07 8.E-07 1.E-06 1.E-06 1.E-06 2.E-06 2.E-06 0.E+00 2.E-06 2.E-07 4.E-07 6.E-07 FIGURE 2-32: Pulse Response. Small-Signal Non-inverting FIGURE 2-35: Response. 1.E-06 1.E-06 1.E-06 2.E-06 2.E-06 2.E-06 Small-Signal Inverting Pulse 5.0 5.0 G = +1 V/V 4.5 G = -1 V/V RF = 1 k: 4.5 Output Voltage (V) 4.0 3.5 3.0 2.5 2.0 1.5 1.0 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0.5 0.0 8.E-07 Time (200 ns/div) Time (200 ns/div) Output Voltage (V) 0 Ambient Temperature (C) 0.E+00 5.E-07 1.E-06 2.E-06 2.E-06 3.E-06 3.E-06 4.E-06 4.E-06 5.E-06 5.E-06 0.0 0.E+00 5.E-07 FIGURE 2-33: Pulse Response. DS21685B-page 10 Large-Signal Non-inverting 1.E-06 2.E-06 2.E-06 3.E-06 3.E-06 4.E-06 4.E-06 5.E-06 5.E-06 Time (500 ns/div) Time (500 ns/div) FIGURE 2-36: Response. Large-Signal Inverting Pulse 2003 Microchip Technology Inc. MCP6021/2/3/4 50 40 30 20 10 0 -10 -20 -30 -40 -50 VREF Accuracy; VREF-VDD/2 (mV) VREF Accuracy; VREF-VDD/2 (mV) Note: Unless otherwise indicated, TA = +25C, VDD = +2.5V to +5.5V, VSS = GND, VCM = VDD/2, RL = 10 k to V DD/2, VOUT VDD/2 and C L = 60 pF. 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 50 40 30 20 10 0 -10 -20 -30 -40 -50 Representative Part VDD = 5.5V VDD = 2.5V -50 FIGURE 2-37: VREF Accuracy vs. Supply Voltage (MCP6021 and MCP6023 only). 25 50 75 100 125 FIGURE 2-40: VREF Accuracy vs. Temperature (MCP6021 and MCP6023 only). Op Amp shuts off here 1.4 Quiescent Current (mA/amplifier) Op Amp turns on here 1.4 Quiescent Current (mA/amplifier) 0 1.6 1.6 1.2 1.0 Hysteresis CS swept high to low 0.8 0.6 VDD = 2.5V G = +1 V/V VIN = 1.25V 0.4 0.2 CS swept low to high Op Amp turns on here Op Amp shuts off here 1.2 Hysteresis 1.0 0.8 CS swept high to low 0.6 0.4 0.2 VDD = 5.5V G = +1 V/V VIN = 2.75V CS swept low to high 0.0 0.0 0.0 0.5 1.0 1.5 2.0 2.5 FIGURE 2-38: Chip Select (CS) Hysteresis (MCP6023 only) with VDD = 2.5V. 5.5 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0.0 -0.5 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 Chip Select Voltage (V) Chip Select Voltage (V) Chip Select Voltage, Output Voltage (V) -25 Ambient Temperature (C) Power Supply Voltage (V) FIGURE 2-41: Chip Select (CS) Hysteresis (MCP6023 only) with VDD = 5.5V. VDD = 5.0V G = +1 V/V VIN = VSS CS Voltage VOUT Output on 0.0E+00 5.0E-06 Output on Output High-Z 1.0E-05 1.5E-05 2.0E-05 2.5E-05 3.0E-05 3.5E-05 Time (5 s/div) FIGURE 2-39: Chip Select (CS) to Amplifier Output Response Time (MCP6023 only). 2003 Microchip Technology Inc. DS21685B-page 11 MCP6021/2/3/4 3.0 APPLICATIONS INFORMATION The MCP6021/2/3/4 family of operational amplifiers are fabricated on Microchip's state-of-the-art CMOS process. They are unity-gain stable and suitable for a wide range of general-purpose applications. 3.1 Rail-to-Rail Input The MCP6021/2/3/4 amplifier family is designed to not exhibit phase inversion when the input pins exceed the supply voltages. Figure 2-27 shows an input voltage exceeding both supplies with no resulting phase inversion. The input stage of the MCP6021/2/3/4 family of devices uses two differential input stages in parallel; one operates at low common-mode input voltage (VCM), while the other operates at high VCM. With this topology, the device operates with VCM up to 0.3V past either supply rail (VSS - 0.3V to VDD + 0.3V) at 25C. The amplifier input behaves linearly as long as VCM is kept within the specified VCMR limits. The input offset voltage is measured at both VCM = VSS - 0.3V and VDD + 0.3V to ensure proper operation. 3.3 MCP6023 Chip Select (CS) The MCP6023 is a single amplifier with chip select (CS). When CS is high, the supply current is less than 10 nA (typ) and travels from the CS pin to VSS, with the amplifier output being put into a high-impedance state. When CS is low, the amplifier is enabled. If CS is left floating, the amplifier will not operate properly. Figure 1-1 and Figure 2-39 show the output voltage and supply current response to a CS pulse. 3.4 MCP6021 and MCP6023 Reference Voltage The single op amps (MCP6021 and MCP6023) have an internal mid-supply reference voltage connected to the VREF pin (see Figure 3-2). The MCP6021 has CS internally tied to VSS, which always keeps the op amp on and always provides a mid-supply reference. With the MCP6023, taking the CS pin high conserves power by shutting down both the op amp and the V REF circuitry. Taking the CS pin low turns on the op amp and VREF circuitry. VDD Input voltages that exceed the input voltage range (VCMR) can cause excessive current to flow in or out of the input pins. Current beyond 2 mA introduces possible reliability problems. Thus, applications that exceed this rating must externally limit the input current with an input resistor (RIN), as shown in Figure 3-1. 50 k VREF 50 k CS RIN MCP602X VOUT VIN (CS tied internally to VSS for MCP6021) R IN R IN (Maximum expected VIN) - VDD 2 mA VSS - (Minimum expected VIN) FIGURE 3-1: into an input pin. 3.2 VSS 2 mA R IN limits the current flow FIGURE 3-2: Simplified internal VREF circuit (MCP6021 and MCP6023 only). See Figure 3-3 for a non-inverting gain circuit using the internal mid-supply reference. The DC-blocking capacitor (CB) also reduces noise by coupling the op amp input to the source. Rail-to-Rail Output The Maximum Output Voltage Swing is the maximum swing possible under a particular output load. According to the specification table, the output can reach within 20 mV of either supply rail when RL = 10 k. See Figure 2-31 and Figure 2-34 for more information concerning typical performance. DS21685B-page 12 RG RF CB VREF VOUT VIN FIGURE 3-3: Non-inverting gain circuit using VREF (MCP6021 and MCP6023 only). 2003 Microchip Technology Inc. MCP6021/2/3/4 To use the internal mid-supply reference for an inverting gain circuit, connect the V REF pin to the noninverting input, as shown in Figure 3-4. The capacitor CB helps reduce power supply noise on the output. Recommended RISO (:) RG 1,000 RF VIN VOUT GN t +1 100 10 VREF 10 100 1,000 10,000 Normalized Capacitance; CL/GN (pF) CB FIGURE 3-6: Recommended RISO values for capacitive loads. FIGURE 3-4: Inverting gain circuit using VREF (MCP6021 and MCP6023 only). If you don't need the mid-supply reference, leave the VREF pin open. 3.5 Capacitive Loads Driving large capacitive loads can cause stability problems for voltage feedback op amps. As the load capacitance increases, the feedback loop's phase margin decreases, and the closed loop bandwidth is reduced. This produces gain-peaking in the frequency response, with overshoot and ringing in the step response. When driving large capacitive loads with these op amps (e.g., > 60 pF when G = +1), a small series resistor at the output (RISO in Figure 3-5) improves the feedback loop's phase margin (stability) by making the load resistive at higher frequencies. The bandwidth will be generally lower than the bandwidth with no capacitive load. VIN RISO VOUT MCP602X CL FIGURE 3-5: Output resistor RISO stabilizes large capacitive loads. Figure 3-6 gives recommended RISO values for different capacitive laods and gains. The x-axis is the normalized load capacitance (C L/G N), where G N is the circuit's noise gain. For non-inverting gains, G N and the gain are equal. For inverting gains, G N is 1+|Gain| (e.g., -1 V/V gives GN = +2 V/V). After selecting R ISO for your circuit, double-check the resulting frequency response peaking and step response overshoot. Evaluation on the bench and simulations with the MCP6021/2/3/4 Spice macro model are very helpful. Modify RISO's value until the response is reasonable. 3.6 Supply Bypass With this family of operational amplifiers, the power supply pin (VDD for single supply) should have a local bypass capacitor (i.e., 0.01 F to 0.1 F) within 2 mm for good, high-frequency performance. It also needs a bulk capacitor (i.e., 1 F or larger) within 100 mm to provide large, slow currents. This bulk capacitor can be shared with other parts. 3.7 PCB Surface Leakage In applications where low input bias current is critical, PCB (printed circuit board) surface-leakage effects need to be considered. Surface leakage is caused by humidity, dust or other contamination on the board. Under low humidity conditions, a typical resistance between nearby traces is 1012. A 5V difference would cause 5 pA of current to flow, which is greater than the MCP6021/2/3/4 family's bias current at 25C (1 pA, typ). The easiest way to reduce surface leakage is to use a guard ring around sensitive pins (or traces). The guard ring is biased at the same voltage as the sensitive pin. An example of this type of layout is shown in Figure 3-7. Guard Ring FIGURE 3-7: 2003 Microchip Technology Inc. VIN- VIN+ Example guard ring layout. DS21685B-page 13 MCP6021/2/3/4 1. Inverting (Figure 3-7) and Transimpedance Gain Amplifiers (convert current to voltage, such as photo detectors). a. b. 2. 3.8 Connect the guard ring to the non-inverting input pin (VIN+). This biases the guard ring to the same reference voltage as the op amp's input (e.g., VDD/2 or ground). Connect the inverting pin (VIN-) to the input with a wire that does not touch the PCB surface. 3.9 Typical Applications 3.9.1 A/D CONVERTER DRIVER AND ANTI-ALIASING FILTER Figure 3-8 shows a third-order Butterworth filter that can be used as an A/D converter driver. It has a bandwidth of 20 kHz and a reasonable step response. It will work well for conversion rates of 80 ksps and greater (it has 29 dB attenuation at 60 kHz). Non-inverting Gain and Unity-Gain Buffer a. Connect the guard ring to the inverting input pin (VIN-); this biases the guard ring to the common mode input voltage. b. Connect the non-inverting pin (VIN+) to the input with a wire that does not touch the PCB surface. High-Speed PCB Layout Due to their speed capabilities, a little extra care in the PCB (Printed Circuit Board) layout can make a significant difference in the performance of these op amps. Good PC board layout techniques will help you achieve the performance shown in the Electrical Characteristics and Typical Performance Curves, while also helping you minimize EMC (Electro-Magnetic Compatibility) issues. Use a solid ground plane and connect the bypass local capacitor(s) to this plane with minimal length traces. This cuts down inductive and capacitive crosstalk. Separate digital from analog, low-speed from highspeed and low power from high power. This will reduce interference. Keep sensitive traces short and straight. Separating them from interfering components and traces. This is especially important for high-frequency (low rise-time) signals. Sometimes it helps to place guard traces next to victim traces. They should be on both sides of the victim trace, and as close as possible. Connect the guard trace to ground plane at both ends, and in the middle for long traces. Use coax cables (or low inductance wiring) to route signal and power to and from the PCB. DS21685B-page 14 1.0 nF 8.45 k 14.7 k 33.2 k 1.2 nF 100 pF MCP602X FIGURE 3-8: A/D converter driver and anti-aliasing filter with a 20 kHz cutoff frequency. This filter can easily be adjusted to another bandwidth by multiplying all capacitors by the same factor. Alternatively, the resistors can all be scaled by another common factor to adjust the bandwidth. 3.9.2 OPTICAL DETECTOR AMPLIFIER Figure 3-9 shows the MCP6021 op amp used as a transimpedance amplifier in a photo detector circuit. The photo detector looks like a capacitive current source, so the 100 k resistor gains the input signal to a reasonable level. The 5.6 pF capacitor stabilizes this circuit and produces a flat frequency response with a bandwidth of 370 kHz. 5.6 pF Photo Detector 100 k 100 pF MCP6021 VDD/2 FIGURE 3-9: Transimpedance amplifier for an optical detector. 2003 Microchip Technology Inc. MCP6021/2/3/4 4.0 DESIGN TOOLS Microchip provides the basic design tools needed for the MCP6021/2/3/4 family of op amps. 4.1 SPICE Macro Model The latest SPICE macro model for the MCP6021/2/3/4 op amps is available on our web site (www.microchip.com). This model is intended as an initial design tool that works well in the op amp's linear region of operation at room temperature. See the model file for information on its capabilities. Bench testing is a very important part of any design and cannot be replaced with simulations. Also, simulation results using this macro model need to be validated by comparing them to the data sheet specs and plots. 4.2 FilterLab(R) Software The FilterLab(R) software is an innovative tool that simplifies analog active filter (using op amps) design. Available at no cost from our web site (at www.microchip.com), the FilterLab software active filter design tool provides full schematic diagrams of the filter circuit with component values. It also outputs the filter circuit in SPICE format, which can be used with the Macro Model to simulate actual filter performance. 2003 Microchip Technology Inc. DS21685B-page 15 MCP6021/2/3/4 5.0 PACKAGING INFORMATION 5.1 Package Marking Information 8-Lead PDIP (300 mil) Example: XXXXXXXX XXXXXNNN YYWW MCP6021 I/P256 0331 8-Lead SOIC (150 mil) XXXXXXXX XXXXYYWW MCP6021 I/SN0331 NNN 256 Example: 8-Lead TSSOP XXXX 6021 YWW E331 NNN 256 Legend: XX...X Y YY WW NNN Note: * Example: Customer specific information* Year code (last digit of calendar year) Year code (last 2 digits of calendar year) Week code (week of January 1 is week `01') Alphanumeric traceability code In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line thus limiting the number of available characters for customer specific information. Standard device marking consists of Microchip part number, year code, week code, and traceability code. DS21685B-page 16 2003 Microchip Technology Inc. MCP6021/2/3/4 Package Marking Information (Continued) 14-Lead PDIP (300 mil) (MCP6024) XXXXXXXXXXXXXX XXXXXXXXXXXXXX YYWWNNN 14-Lead SOIC (150 mil) (MCP6024) Example: MCP6024-I/P XXXXXXXXXXXXXX 0331256 Example: MCP6024ISL XXXXXXXXXX 0331256 XXXXXXXXXX XXXXXXXXXX YYWWNNN 14-Lead TSSOP (MCP6024) Example: XXXXXX YYWW 6024E 0331 NNN 256 2003 Microchip Technology Inc. DS21685B-page 17 MCP6021/2/3/4 8-Lead Plastic Dual In-line (P) - 300 mil (PDIP) E1 D 2 n 1 E A2 A L c A1 B1 p eB B Units Dimension Limits n p Number of Pins Pitch Top to Seating Plane Molded Package Thickness Base to Seating Plane Shoulder to Shoulder Width Molded Package Width Overall Length Tip to Seating Plane Lead Thickness Upper Lead Width Lower Lead Width Overall Row Spacing Mold Draft Angle Top Mold Draft Angle Bottom * Controlling Parameter Significant Characteristic A A2 A1 E E1 D L c B1 B eB MIN .140 .115 .015 .300 .240 .360 .125 .008 .045 .014 .310 5 5 INCHES* NOM MAX 8 .100 .155 .130 .170 .145 .313 .250 .373 .130 .012 .058 .018 .370 10 10 .325 .260 .385 .135 .015 .070 .022 .430 15 15 MILLIMETERS NOM 8 2.54 3.56 3.94 2.92 3.30 0.38 7.62 7.94 6.10 6.35 9.14 9.46 3.18 3.30 0.20 0.29 1.14 1.46 0.36 0.46 7.87 9.40 5 10 5 10 MIN MAX 4.32 3.68 8.26 6.60 9.78 3.43 0.38 1.78 0.56 10.92 15 15 Notes: Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010" (0.254mm) per side. JEDEC Equivalent: MS-001 Drawing No. C04-018 DS21685B-page 18 2003 Microchip Technology Inc. MCP6021/2/3/4 8-Lead Plastic Small Outline (SN) - Narrow, 150 mil (SOIC) E E1 p D 2 B n 1 h 45 c A2 A L Units Dimension Limits n p Number of Pins Pitch Overall Height Molded Package Thickness Standoff Overall Width Molded Package Width Overall Length Chamfer Distance Foot Length Foot Angle Lead Thickness Lead Width Mold Draft Angle Top Mold Draft Angle Bottom * Controlling Parameter Significant Characteristic A A2 A1 E E1 D h L c B MIN .053 .052 .004 .228 .146 .189 .010 .019 0 .008 .013 0 0 A1 INCHES* NOM 8 .050 .061 .056 .007 .237 .154 .193 .015 .025 4 .009 .017 12 12 MAX .069 .061 .010 .244 .157 .197 .020 .030 8 .010 .020 15 15 MILLIMETERS NOM 8 1.27 1.35 1.55 1.32 1.42 0.10 0.18 5.79 6.02 3.71 3.91 4.80 4.90 0.25 0.38 0.48 0.62 0 4 0.20 0.23 0.33 0.42 0 12 0 12 MIN MAX 1.75 1.55 0.25 6.20 3.99 5.00 0.51 0.76 8 0.25 0.51 15 15 Notes: Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010" (0.254mm) per side. JEDEC Equivalent: MS-012 Drawing No. C04-057 2003 Microchip Technology Inc. DS21685B-page 19 MCP6021/2/3/4 8-Lead Plastic Thin Shrink Small Outline (ST) - 4.4 mm (TSSOP) E E1 p D 2 1 n B A c A1 A2 L Units Dimension Limits n p Number of Pins Pitch Overall Height Molded Package Thickness Standoff Overall Width Molded Package Width Molded Package Length Foot Length Foot Angle Lead Thickness Lead Width Mold Draft Angle Top Mold Draft Angle Bottom * Controlling Parameter Significant Characteristic A A2 A1 E E1 D L c B MIN INCHES NOM MAX 8 .026 .033 .002 .246 .169 .114 .020 0 .004 .007 0 0 .035 .004 .251 .173 .118 .024 4 .006 .010 5 5 .043 .037 .006 .256 .177 .122 .028 8 .008 .012 10 10 MILLIMETERS* NOM MAX 8 0.65 1.10 0.85 0.90 0.95 0.05 0.10 0.15 6.25 6.38 6.50 4.30 4.40 4.50 2.90 3.00 3.10 0.50 0.60 0.70 0 4 8 0.09 0.15 0.20 0.19 0.25 0.30 0 5 10 0 5 10 MIN Notes: Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .005" (0.127mm) per side. JEDEC Equivalent: MO-153 Drawing No. C04-086 DS21685B-page 20 2003 Microchip Technology Inc. MCP6021/2/3/4 14-Lead Plastic Dual In-line (P) - 300 mil (PDIP) E1 D 2 n 1 E A2 A L c A1 eB B1 p B Units Dimension Limits n p MIN INCHES* NOM 14 .100 .155 .130 MAX MILLIMETERS NOM 14 2.54 3.56 3.94 2.92 3.30 0.38 7.62 7.94 6.10 6.35 18.80 19.05 3.18 3.30 0.20 0.29 1.14 1.46 0.36 0.46 7.87 9.40 5 10 5 10 MIN Number of Pins Pitch Top to Seating Plane A .140 .170 Molded Package Thickness A2 .115 .145 Base to Seating Plane A1 .015 Shoulder to Shoulder Width E .300 .313 .325 Molded Package Width E1 .240 .250 .260 Overall Length D .740 .750 .760 Tip to Seating Plane L .125 .130 .135 c Lead Thickness .008 .012 .015 Upper Lead Width B1 .045 .058 .070 Lower Lead Width B .014 .018 .022 Overall Row Spacing eB .310 .370 .430 Mold Draft Angle Top 5 10 15 Mold Draft Angle Bottom 5 10 15 * Controlling Parameter Significant Characteristic Notes: Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010" (0.254mm) per side. JEDEC Equivalent: MS-001 Drawing No. C04-005 2003 Microchip Technology Inc. MAX 4.32 3.68 8.26 6.60 19.30 3.43 0.38 1.78 0.56 10.92 15 15 DS21685B-page 21 MCP6021/2/3/4 14-Lead Plastic Small Outline (SL) - Narrow, 150 mil (SOIC) E E1 p D 2 B n 1 h 45 c A2 A A1 L Units Dimension Limits n p Number of Pins Pitch Overall Height Molded Package Thickness Standoff Overall Width Molded Package Width Overall Length Chamfer Distance Foot Length Foot Angle Lead Thickness Lead Width Mold Draft Angle Top Mold Draft Angle Bottom * Controlling Parameter Significant Characteristic A A2 A1 E E1 D h L c B MIN .053 .052 .004 .228 .150 .337 .010 .016 0 .008 .014 0 0 INCHES* NOM 14 .050 .061 .056 .007 .236 .154 .342 .015 .033 4 .009 .017 12 12 MAX .069 .061 .010 .244 .157 .347 .020 .050 8 .010 .020 15 15 MILLIMETERS NOM 14 1.27 1.35 1.55 1.32 1.42 0.10 0.18 5.79 5.99 3.81 3.90 8.56 8.69 0.25 0.38 0.41 0.84 0 4 0.20 0.23 0.36 0.42 0 12 0 12 MIN MAX 1.75 1.55 0.25 6.20 3.99 8.81 0.51 1.27 8 0.25 0.51 15 15 Notes: Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010" (0.254mm) per side. JEDEC Equivalent: MS-012 Drawing No. C04-065 DS21685B-page 22 2003 Microchip Technology Inc. MCP6021/2/3/4 14-Lead Plastic Thin Shrink Small Outline (ST) - 4.4 mm (TSSOP) E E1 p D 2 1 n B A c A1 L Units Dimension Limits n p Number of Pins Pitch Overall Height Molded Package Thickness Standoff Overall Width Molded Package Width Molded Package Length Foot Length Foot Angle Lead Thickness Lead Width Mold Draft Angle Top Mold Draft Angle Bottom * Controlling Parameter Significant Characteristic A A2 A1 E E1 D L c B MIN .033 .002 .246 .169 .193 .020 0 .004 .007 0 0 INCHES NOM 14 .026 .035 .004 .251 .173 .197 .024 4 .006 .010 5 5 A2 MAX .043 .037 .006 .256 .177 .201 .028 8 .008 .012 10 10 MILLIMETERS* NOM MAX 14 0.65 1.10 0.85 0.90 0.95 0.05 0.10 0.15 6.25 6.38 6.50 4.30 4.40 4.50 4.90 5.00 5.10 0.50 0.60 0.70 0 4 8 0.09 0.15 0.20 0.19 0.25 0.30 0 5 10 0 5 10 MIN Notes: Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .005" (0.127mm) per side. JEDEC Equivalent: MO-153 Drawing No. C04-087 2003 Microchip Technology Inc. DS21685B-page 23 MCP6021/2/3/4 NOTES: DS21685B-page 24 2003 Microchip Technology Inc. MCP6021/2/3/4 PRODUCT IDENTIFICATION SYSTEM To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office. PART NO. X /XX Device Temperature Range Package Examples: a) b) c) Device: MCP6021 MCP6021T MCP6022 MCP6022T MCP6023 MCP6023T MCP6024 MCP6024T CMOS Single Op Amp CMOS Single Op Amp (Tape and Reel for SOIC, TSSOP) CMOS Dual Op Amp CMOS Dual Op Amp (Tape and Reel for SOIC and TSSOP) CMOS Single Op Amp w/ CS Function CMOS Single Op Amp w/ CS Function (Tape and Reel for SOIC and TSSOP) CMOS Quad Op Amp CMOS Quad Op Amp (Tape and Reel for SOIC and TSSOP) Temperature Range: I E = -40C to +85C = -40xC to +125xC Package: P SN SL ST = = = = a) b) c) a) b) c) a) Plastic DIP (300 mil Body), 8-lead, 14-lead Plastic SOIC (150mil Body), 8-lead Plastic SOIC (150 mil Body), 14-lead Plastic TSSOP, 8-lead, 14-lead b) c) MCP6021-I/P: Industrial temperature, PDIP package. MCP6021-E/P: Extended temperature, PDIP package. MCP6021-E/SN: Extended temperature, SOIC package. MCP6022-I/P: Industrial temperature, PDIP package. MCP6022-E/P: Extended temperature, PDIP package. MCP6022T-E/ST: Tape and Reel, Extended temperature, TSSOP package. MCP6023-I/P: Industrial temperature, PDIP package. MCP6023-E/P: Extended temperature, PDIP package. MCP6023-E/SN: Extended temperature, SOIC package. MCP6024-I/SL: Industrial temperature, SOIC package. MCP6024-E/SL: Extended temperature, SOIC package. MCP6024T-E/ST: Tape and Reel, Extended temperature, TSSOP package. Sales and Support Data Sheets Products supported by a preliminary Data Sheet may have an errata sheet describing minor operational differences and recommended workarounds. To determine if an errata sheet exists for a particular device, please contact one of the following: 1. 2. 3. Your local Microchip sales office The Microchip Corporate Literature Center U.S. FAX: (480) 792-7277 The Microchip Worldwide Site (www.microchip.com) Please specify which device, revision of silicon and Data Sheet (include Literature #) you are using. Customer Notification System Register on our web site (www.microchip.com/cn) to receive the most current information on our products. 2003 Microchip Technology Inc. DS21685B-page 25 MCP6021/2/3/4 NOTES: DS21685B-page 26 2003 Microchip Technology Inc. Note the following details of the code protection feature on Microchip devices: * Microchip products meet the specification contained in their particular Microchip Data Sheet. * Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. * There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip's Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property. * Microchip is willing to work with the customer who is concerned about the integrity of their code. * Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as "unbreakable." Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break microchip's code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. Information contained in this publication regarding device applications and the like is intended through suggestion only and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. No representation or warranty is given and no liability is assumed by Microchip Technology Incorporated with respect to the accuracy or use of such information, or infringement of patents or other intellectual property rights arising from such use or otherwise. Use of Microchip's products as critical components in life support systems is not authorized except with express written approval by Microchip. No licenses are conveyed, implicitly or otherwise, under any intellectual property rights. Trademarks The Microchip name and logo, the Microchip logo, Accuron, dsPIC, KEELOQ, MPLAB, PIC, PICmicro, PICSTART, PRO MATE and PowerSmart are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. AmpLab, FilterLab, microID, MXDEV, MXLAB, PICMASTER, SEEVAL and The Embedded Control Solutions Company are registered trademarks of Microchip Technology Incorporated in the U.S.A. Application Maestro, dsPICDEM, dsPICDEM.net, ECAN, ECONOMONITOR, FanSense, FlexROM, fuzzyLAB, In-Circuit Serial Programming, ICSP, ICEPIC, microPort, Migratable Memory, MPASM, MPLIB, MPLINK, MPSIM, PICkit, PICDEM, PICDEM.net, PowerCal, PowerInfo, PowerMate, PowerTool, rfLAB, rfPIC, Select Mode, SmartSensor, SmartShunt, SmartTel and Total Endurance are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. Serialized Quick Turn Programming (SQTP) is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. (c) 2003, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. Microchip received QS-9000 quality system certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona in July 1999 and Mountain View, California in March 2002. The Company's quality system processes and procedures are QS-9000 compliant for its PICmicro(R) 8-bit MCUs, KEELOQ(R) code hopping devices, Serial EEPROMs, microperipherals, non-volatile memory and analog products. In addition, Microchip's quality system for the design and manufacture of development systems is ISO 9001 certified. 2003 Microchip Technology Inc. DS21685B-page 27 M WORLDWIDE SALES AND SERVICE AMERICAS ASIA/PACIFIC Corporate Office Australia 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: 480-792-7627 Web Address: http://www.microchip.com Suite 22, 41 Rawson Street Epping 2121, NSW Australia Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 Atlanta Unit 915 Bei Hai Wan Tai Bldg. No. 6 Chaoyangmen Beidajie Beijing, 100027, No. China Tel: 86-10-85282100 Fax: 86-10-85282104 3780 Mansell Road, Suite 130 Alpharetta, GA 30022 Tel: 770-640-0034 Fax: 770-640-0307 Boston 2 Lan Drive, Suite 120 Westford, MA 01886 Tel: 978-692-3848 Fax: 978-692-3821 Chicago 333 Pierce Road, Suite 180 Itasca, IL 60143 Tel: 630-285-0071 Fax: 630-285-0075 Dallas 4570 Westgrove Drive, Suite 160 Addison, TX 75001 Tel: 972-818-7423 Fax: 972-818-2924 Detroit Tri-Atria Office Building 32255 Northwestern Highway, Suite 190 Farmington Hills, MI 48334 Tel: 248-538-2250 Fax: 248-538-2260 Kokomo 2767 S. Albright Road Kokomo, IN 46902 Tel: 765-864-8360 Fax: 765-864-8387 Los Angeles China - Beijing China - Chengdu Rm. 2401-2402, 24th Floor, Ming Xing Financial Tower No. 88 TIDU Street Chengdu 610016, China Tel: 86-28-86766200 Fax: 86-28-86766599 China - Fuzhou Unit 28F, World Trade Plaza No. 71 Wusi Road Fuzhou 350001, China Tel: 86-591-7503506 Fax: 86-591-7503521 China - Hong Kong SAR Unit 901-6, Tower 2, Metroplaza 223 Hing Fong Road Kwai Fong, N.T., Hong Kong Tel: 852-2401-1200 Fax: 852-2401-3431 China - Shanghai Room 701, Bldg. B Far East International Plaza No. 317 Xian Xia Road Shanghai, 200051 Tel: 86-21-6275-5700 Fax: 86-21-6275-5060 China - Shenzhen 18201 Von Karman, Suite 1090 Irvine, CA 92612 Tel: 949-263-1888 Fax: 949-263-1338 Rm. 1812, 18/F, Building A, United Plaza No. 5022 Binhe Road, Futian District Shenzhen 518033, China Tel: 86-755-82901380 Fax: 86-755-8295-1393 Phoenix China - Shunde 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7966 Fax: 480-792-4338 Room 401, Hongjian Building No. 2 Fengxiangnan Road, Ronggui Town Shunde City, Guangdong 528303, China Tel: 86-765-8395507 Fax: 86-765-8395571 San Jose China - Qingdao 2107 North First Street, Suite 590 San Jose, CA 95131 Tel: 408-436-7950 Fax: 408-436-7955 Rm. B505A, Fullhope Plaza, No. 12 Hong Kong Central Rd. Qingdao 266071, China Tel: 86-532-5027355 Fax: 86-532-5027205 Toronto India 6285 Northam Drive, Suite 108 Mississauga, Ontario L4V 1X5, Canada Tel: 905-673-0699 Fax: 905-673-6509 Divyasree Chambers 1 Floor, Wing A (A3/A4) No. 11, O'Shaugnessey Road Bangalore, 560 025, India Tel: 91-80-2290061 Fax: 91-80-2290062 Japan Benex S-1 6F 3-18-20, Shinyokohama Kohoku-Ku, Yokohama-shi Kanagawa, 222-0033, Japan Tel: 81-45-471- 6166 Fax: 81-45-471-6122 DS21685B-page 28 Korea 168-1, Youngbo Bldg. 3 Floor Samsung-Dong, Kangnam-Ku Seoul, Korea 135-882 Tel: 82-2-554-7200 Fax: 82-2-558-5932 or 82-2-558-5934 Singapore 200 Middle Road #07-02 Prime Centre Singapore, 188980 Tel: 65-6334-8870 Fax: 65-6334-8850 Taiwan Kaohsiung Branch 30F - 1 No. 8 Min Chuan 2nd Road Kaohsiung 806, Taiwan Tel: 886-7-536-4818 Fax: 886-7-536-4803 Taiwan Taiwan Branch 11F-3, No. 207 Tung Hua North Road Taipei, 105, Taiwan Tel: 886-2-2717-7175 Fax: 886-2-2545-0139 EUROPE Austria Durisolstrasse 2 A-4600 Wels Austria Tel: 43-7242-2244-399 Fax: 43-7242-2244-393 Denmark Regus Business Centre Lautrup hoj 1-3 Ballerup DK-2750 Denmark Tel: 45-4420-9895 Fax: 45-4420-9910 France Parc d'Activite du Moulin de Massy 43 Rue du Saule Trapu Batiment A - ler Etage 91300 Massy, France Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Germany Steinheilstrasse 10 D-85737 Ismaning, Germany Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 Italy Via Quasimodo, 12 20025 Legnano (MI) Milan, Italy Tel: 39-0331-742611 Fax: 39-0331-466781 Netherlands P. A. De Biesbosch 14 NL-5152 SC Drunen, Netherlands Tel: 31-416-690399 Fax: 31-416-690340 United Kingdom 505 Eskdale Road Winnersh Triangle Wokingham Berkshire, England RG41 5TU Tel: 44-118-921-5869 Fax: 44-118-921-5820 07/28/03 2003 Microchip Technology Inc.