RMCG Series
Gold Barrier Thick Film Chip Resistors
Rev Date: 02/21/2012 2 www.seielect.com
This specification may be changed at any time without prior notice marketing@seielect.com
Please confirm technical specifications before you order and/or use.
Stackpole Electronics, Inc.
Resistive Product Solutions
Operating Temperature Range: -55ºC to +125ºC (0402)
-55ºC to +155ºC (0603 - 2512)
Dielectric Withstanding Voltage
Resistance to Soldering Heat ± (1% + 0.05Ω)
± (2% + 0.1Ω)
± (1% + 0.05Ω)
Test ResultsTest Test Conditions (JIS C 5202)
Short Time Overload
1/10 rated voltage for 3 sec. max. then rated voltage for 3 sec. max.
2.5x rated voltage for 5 seconds
100 VAC, 1 minute
260ºC ±5ºC, for 10 sec. ±0.5 sec. (Solder Bath)
245ºC ±5ºC, for 3 sec. ±0.5 sec. (Colophonium flux)
-55ºC: 30 min. 25ºC: 2 to 3 min.
125ºC: 30 min. 25ºC: 2 to 3 min.
60ºC ± 2ºC, 90% RH, Rated Load
Temperature Cycle (100 cycles)
Endurance (Damp load)
Jumper (<0.05Ω)
Solderability 95% coverage, minimum
±(1% + 0.05Ω)
±(3% + 0.1Ω)
Jumper (<0.05Ω)90 min. On, 30 min. Off (1,000 hrs. -0hrs. +48hrs.)
Robustness of Termination
Endurance (Rated load) 70ºC ± 2ºC, Rated Load ±(3% + 0.1Ω)
90 min. On, 30 min. Off (1,000 hrs. -0hrs. +48hrs.) Jumper (<0.05Ω)
Voltage Coefficient ±100 (ppm/V)
± (1% + 0.05 Ohm)Bend of 3mm for 5 ± 1 sec.
0.039 ± 0.002 0.020 ± 0.002 0.014 ± 0.002 0.008 ± 0.004 0.010 ± 0.002 / -0.004 inches
1.00 ± 0.05 0.50 ± 0.05 0.35 ± 0.05 0.20 ± 0.10 0.25 + 0.05 / -0.10 mm
0.063 ± 0.004 0.031 ± 0.004 0.018 ± 0.004 0.012 ± 0.008 0.012 ± 0.008 inches
1.60 ± 0.10 0.80 ± 0.10 0.45 ± 0.10 0.30 ± 0.20 0.30 ± 0.20 mm
0.079 ± 0.008 0.049 ± 0.004 0.020 ± 0.006 0.016 ± 0.008 0.016 ± 0.008 inches
2.00 ± 0.20 1.25 ± 0.10 0.50 ± 0.15 0.40 ± 0.20 0.40 ± 0.20 mm
0.126 ± 0.008 0.063 ± 0.006 0.022 ± 0.006 0.020 ± 0.010 0.020 ± 0.010 inches
3.20 ± 0.20 1.60 ± 0.15 0.55 ± 0.15 0.50 ± 0.25 0.50 ± 0.25 mm
0.126 ± 0.008 0.098 ± 0.008 0.022 ± 0.006 0.020 ± 0.010 0.020 ± 0.010 inches
3.20 ± 0.20 2.50 ± 0.20 0.55 ± 0.15 0.50 ± 0.25 0.50 ± 0.25 mm
0.197 ± 0.008 0.098 ± 0.008 0.022 ± 0.006 0.024 ± 0.010 0.024 ± 0.010 inches
5.00 ± 0.20 2.50 ± 0.20 0.55 ± 0.15 0.60 ± 0.25 0.60 ± 0.25 mm
0.248 ± 0.008 0.126 ± 0.008 0.022 ± 0.006 0.024 ± 0.010 0.024 ± 0.010 inches
6.30 ± 0.20 3.20 ± 0.20 0.55 ± 0.15 0.60 ± 0.25 0.60 ± 0.25 mm
RMCG2512
RMCG0805
RMCG1206
RMCG1210
RMCG2010
Unit
RMCG0402
RMCG0603
Type / Code L
Body Length
W
Body Width
H
Body Height
a
Top Termination
b
Bottom Termination
Performance Characteristics
Mechanical Specifications