TPS76815-Q1, TPS76818-Q1, TPS76825-Q1, TPS76827-Q1
TPS76828-Q1, TPS76830-Q1 TPS76833-Q1, TPS76850-Q1, TPS76801-Q1
FAST-TRANSIENT-RESPONSE 1-A LOW-DROPOUT VOLTAGE REGULATORS
SGLS155A − FEBRUARY 2003 − REVISED SEPTEMBER 2008
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
DQualified for Automotive Applications
DESD Protection Exceeds 2000 V Per
MIL-STD-883, Method 3015; Exceeds 200 V
Using Machine Model (C = 200 pF, R = 0)
D1-A Low-Dropout Voltage Regulator
DAvailable in 1.5-V, 1.8-V, 2.5-V, 2.7-V, 2.8-V,
3.0-V, 3.3-V, 5.0-V Fixed Output and
Adjustable Versions
DDropout Voltage Down to 230 mV at 1 A
(TPS76850)
DUltralow 85-µA Typical Quiescent Current
DFast Transient Response
D2% Tolerance Over Specified Conditions for
Fixed-Output Versions
DOpen-Drain Power Good (See TPS767xx for
Power-On Reset With 200-ms Delay Option)
D20-Pin TSSOP (PWP) Package
DThermal Shutdown Protection
description
This device is designed to have a fast transient response and be stable with 10-µF low ESR capacitors. This
combination provides high performance at a reasonable cost.
Because the PMOS device behaves as a low-value resistor, the dropout voltage is very low (typically 230 mV
at an output current of 1 A for the TPS76850) and is directly proportional to the output current. Additionally, since
the PMOS pass element is a voltage-driven device, the quiescent current is very low and independent of output
loading (typically 85 µA over the full range of output current, 0 mA to 1 A). These two key specifications yield
a significant improvement in operating life for battery-powered systems. This LDO family also features a sleep
mode; applying a TTL high signal to EN (enable) shuts down the regulator, reducing the quiescent current to
less than 1 µA at TJ = 25°C.
Power good (PG) is an active high output, which can be used to implement a power-on reset or a low-battery
indicator.
The TPS768xx is offered in 1.5-V, 1.8-V, 2.5-V, 2.7-V, 2.8-V, 3.0-V, 3.3-V, and 5.0-V fixed-voltage versions and
in an adjustable version (programmable over the range of 1.2 V to 5.5 V). Output voltage tolerance is specified
as a maximum of 2% over line, load, and temperature ranges. The TPS768xx family is available in a 20-pin PWP
package.
Copyright 2008, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
NC − No internal connection
1
2
3
4
5
6
7
8
9
10
20
19
18
17
16
15
14
13
12
11
GND/HSINK
GND/HSINK
GND
NC
EN
IN
IN
NC
GND/HSINK
GND/HSINK
GND/HSINK
GND/HSINK
NC
NC
PG
FB/NC
OUT
OUT
GND/HSINK
GND/HSINK
PWP PACKAGE
(TOP VIEW)
TPS76815-Q1, TPS76818-Q1, TPS76825-Q1, TPS76827-Q1
TPS76828-Q1, TPS76830-Q1 TPS76833-Q1, TPS76850-Q1, TPS76801-Q1
FAST-TRANSIENT-RESPONSE 1-A LOW-DROPOUT VOLTAGE REGULATORS
SGLS155A − FEBRUARY 2003 − REVISED SEPTEMBER 2008
2POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
description (continued)
TA − Free-Air Temperature − °C
−40 0 20 120
103
−60 40 60 80 100
− Dropout Voltage − mV
VDO
TPS76833
DROPOUT VOLTAGE
vs
FREE-AIR TEMPERATURE
102
101
100
10−1
10−2
−20 140
IO = 1 A
IO = 10 mA
IO = 0
Co = 10 µF
t − Time − µs
LOAD TRANSIENT RESPONSE
I − Output Current − A
O
VO− Change in∆
Output Voltage − mV
1
0.5
300200100 400 500 700600 800 900 1000
0
Co = 10 µF
TA = 25°C
0
0
50
100
−50
−100
ORDERING INFORMATION{
TJ
OUTPUT
VOLTAGE
(V) PACKAGE}ORDERABLE PART
NUMBER
TOP-SIDE
MARKING
TYP
NUMBER
MARKING
5.0 TPS76850QPWPRQ1 76850Q1
3.3 TPS76833QPWPRQ1 76833Q1
3.0 TPS76830QPWPRQ1§76830Q1§
2.8 TPS76828QPWPRQ1§76828Q1§
−40
°
Cto125
°
C
2.7
TSSOP - PWP
Tape and reel
TPS76827QPWPRQ1§76827Q1§
−
40
°
C
to
125
°
C
2.5
TSSOP
-
PWP
T
ape an
d
ree
l
TPS76825QPWPRQ1 76825Q1
1.8 TPS76818QPWPRQ1 76818Q1
1.5 TPS76815QPWPRQ1 76815Q1
Adjustable
1.2 V to 5.5 V TPS76801QPWPRQ1 76801Q1
†For the most current package and ordering information, see the Package Option Addendum at the end of this document,
or see the TI web site at http://www.ti.com.
‡Package drawings, thermal data, and symbolization are available at http://www.ti.com/packaging.
§This device is Product Preview.
The TPS76801 is programmable using an external resistor divider (see application information). The PWP package is
available taped and reeled. Note R suffix to the device type (e.g., TPS76801QPWPRQ1).
TPS76815-Q1, TPS76818-Q1, TPS76825-Q1, TPS76827-Q1
TPS76828-Q1, TPS76830-Q1 TPS76833-Q1, TPS76850-Q1, TPS76801-Q1
FAST-TRANSIENT-RESPONSE 1-A LOW-DROPOUT VOLTAGE REGULATORS
SGLS155A − FEBRUARY 2003 − REVISED SEPTEMBER 2008
3
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
description (continued)
†See application information section for capacitor selection details.
PG
OUT
OUT
7
6
5
IN
IN
EN
GND
3
16
14
13
VI
0.1 µF
PG
VO
10 µF
+
TPS768xx
Co†
Figure 1. Typical Application Configuration (For Fixed Output Options)
functional block diagram—adjustable version
_
+
Vref = 1.1834 V
OUT
FB/NC
EN
GND
PG
_
+
IN
External to the device
R1
R2
TPS76815-Q1, TPS76818-Q1, TPS76825-Q1, TPS76827-Q1
TPS76828-Q1, TPS76830-Q1 TPS76833-Q1, TPS76850-Q1, TPS76801-Q1
FAST-TRANSIENT-RESPONSE 1-A LOW-DROPOUT VOLTAGE REGULATORS
SGLS155A − FEBRUARY 2003 − REVISED SEPTEMBER 2008
4POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
functional block diagram—fixed-voltage version
_
+
Vref = 1.1834 V
OUT
EN
GND
R1
R2
_
+
IN
PG
Terminal Functions
PWP Package
TERMINAL
I/O
DESCRIPTION
NAME NO. I/O DESCRIPTION
GND/HSINK 1 Ground/heatsink
GND/HSINK 2 Ground/heatsink
GND 3 LDO ground
NC 4 No connect
EN 5 I Enable input
IN 6 I Input
IN 7 I Input
NC 8 No connect
GND/HSINK 9 Ground/heatsink
GND/HSINK 10 Ground/heatsink
GND/HSINK 11 Ground/heatsink
GND/HSINK 12 Ground/heatsink
OUT 13 O Regulated output voltage
OUT 14 O Regulated output voltage
FB/NC 15 I Feedback input voltage for adjustable device (no connect for fixed options)
PG 16 O PG output
NC 17 No connect
NC 18 No connect
GND/HSINK 19 Ground/heatsink
GND/HSINK 20 Ground/heatsink
TPS76815-Q1, TPS76818-Q1, TPS76825-Q1, TPS76827-Q1
TPS76828-Q1, TPS76830-Q1 TPS76833-Q1, TPS76850-Q1, TPS76801-Q1
FAST-TRANSIENT-RESPONSE 1-A LOW-DROPOUT VOLTAGE REGULATORS
SGLS155A − FEBRUARY 2003 − REVISED SEPTEMBER 2008
5
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Input voltage range‡, VI −0.3 V to 13.5 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Voltage range at EN −0.3 V to VI + 0.3 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maximum PG voltage 16.5 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Peak output current Internally limited. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Continuous total power dissipation See dissipation rating tables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Output voltage, VO (OUT, FB) 7 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Thermal impedance, Junction-to-Air, ΘJA 42.55°C/W. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating virtual junction temperature range, TJ −40°C to 150°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Storage temperature range, Tstg −65°C to 150°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ESD rating, HBM 2 kV. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
†Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
‡All voltage values are with respect to network terminal ground.
recommended operating conditions
MIN MAX UNIT
Input voltage, VI§2.7 10 V
Output voltage range, VO1.2 5.5 V
Output current, IO (see Note 1) 0 1.0 A
Operating virtual junction temperature, TJ (see Note 1) −40 125 °C
§ To calculate the minimum input voltage for your maximum output current, use the following equation: VI(min) = VO(max) + VDO(max load).
NOTE 1: Continuous current and operating junction temperature are limited by internal protection circuitry, but it is not recommended that the
device operate under conditions beyond those specified in this table for extended periods of time.
TPS76815-Q1, TPS76818-Q1, TPS76825-Q1, TPS76827-Q1
TPS76828-Q1, TPS76830-Q1 TPS76833-Q1, TPS76850-Q1, TPS76801-Q1
FAST-TRANSIENT-RESPONSE 1-A LOW-DROPOUT VOLTAGE REGULATORS
SGLS155A − FEBRUARY 2003 − REVISED SEPTEMBER 2008
6POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
electrical characteristics over recommended operating free-air temperature range,
VI = VO(typ) + 1 V, IO = 1 mA, EN = 0 V, Co = 10 µF (unless otherwise noted)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
TPS76801
5.5 V ≥ VO ≥ 1.5 V, TJ = 25°C VO
TPS76801 5.5 V ≥ VO ≥ 1.5 V, TJ = −40°C to 125°C 0.98VO1.02VO
TPS76815
TJ = 25°C, 2.7 V < VIN < 10 V 1.5
TPS76815 TJ = −40°C to 125°C, 2.7 V < VIN < 10 V 1.470 1.530
TPS76818
TJ = 25°C, 2.8 V < VIN < 10 V 1.8
TPS76818 TJ = −40°C to 125°C, 2.8 V < VIN < 10 V 1.764 1.836
TPS76825
TJ = 25°C, 3.5 V < VIN < 10 V 2.5
TPS76825 TJ = −40°C to 125°C, 3.5 V < VIN < 10 V 2.450 2.550
Output voltage
(10 µA to 1 A load)
TPS76827
TJ = 25°C, 3.7 V < VIN < 10 V 2.7
V
(10 µA to 1 A load)
(see
N
o
t
e
2
)
TPS76827 TJ = −40°C to 125°C, 3.7 V < VIN < 10 V 2.646 2.754 V
(see
Note
2)
TPS76828
TJ = 25°C, 3.8 V < VIN < 10 V 2.8
TPS76828 TJ = −40°C to 125°C, 3.8 V < VIN < 10 V 2.744 2.856
TPS76830
TJ = 25°C, 4 V < VIN < 10 V 3.0
TPS76830 TJ = −40°C to 125°C, 4 V < VIN < 10 V 2.940 3.060
TPS76833
TJ = 25°C, 4.3 V < VIN < 10 V 3.3
TPS76833 TJ = −40°C to 125°C, 4.3 V < VIN < 10 V 3.234 3.366
TPS76850
TJ = 25°C, 6 V < VIN < 10 V 5.0
TPS76850 TJ = −40°C to 125°C, 6 V < VIN < 10 V 4.900 5.100
Quiescent current (GND current) 10 µA < IO < 1 A, TJ = 25°C 85
A
Quiescent
current
(GND
current)
EN = 0V, (see Note 2) IO = 1 A, TJ = −40°C to 125°C 125 µA
Output voltage line regulation (∆VO/VO)
(see Notes 2 and 3) VO + 1 V < VI ≤ 10 V, TJ = 25°C 0.01 %/V
Load regulation 3 mV
Output noise voltage (TPS76818) BW = 200 Hz to 100 kHz,
Co = 10 µF, I C = 1 A, TJ = 25°C55 µVrms
Output current limit VO = 0 V 1.7 2 A
Thermal shutdown junction temperature 150 °C
Standby current
EN = VI,T
J = 25°C,
2.7 V < VI < 10 V 1µA
Standby current EN = VI,T
J = −40°C to 125°C
2.7 V < VI < 10 V 10 µA
FB input current TPS76801 FB = 1.5 V 2 nA
High level enable input voltage 1.7 V
Low level enable input voltage 0.9 V
Power supply ripple rejection (see Note 2) f = 1 KHz, Co = 10 µF,
TJ = 25°C60 dB
NOTES: 2. Minimum IN operating voltage is 2.7 V or VO(typ) + 1 V, whichever is greater. Maximum IN voltage 10 V.
3. If VO ≤ 1.8 V then VImax = 10 V, VImin = 2.7 V:
Line Reg. (mV) +ǒ%ńVǓ
VOǒVImax *2.7 VǓ
100 1000
If VO ≥ 2.5 V then VImax = 10 V, VImin = VO + 1 V:
Line Reg. (mV) +ǒ%ńVǓ
VOǒVImax *ǒVO)1V
ǓǓ
100 1000
TPS76815-Q1, TPS76818-Q1, TPS76825-Q1, TPS76827-Q1
TPS76828-Q1, TPS76830-Q1 TPS76833-Q1, TPS76850-Q1, TPS76801-Q1
FAST-TRANSIENT-RESPONSE 1-A LOW-DROPOUT VOLTAGE REGULATORS
SGLS155A − FEBRUARY 2003 − REVISED SEPTEMBER 2008
7
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
electrical characteristics over recommended operating free-air temperature range,
VI = VO(typ) + 1 V, IO = 1 mA, EN = 0 V, Co = 10 µF (unless otherwise noted) (continued)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
Minimum input voltage for valid PG IO(PG) = 300 µA 1.1 V
Trip threshold voltage VO decreasing 92 98 %VO
PG Hysteresis voltage Measured at VO0.5 %VO
PG
Output low voltage VI = 2.7 V, IO(PG) = 1 mA 0.15 0.4 V
Leakage current V(PG) = 5 V 1µA
EN = 0 V −1 0 1
A
Input current (EN)EN = VI−1 1 µA
TPS76828
IO = 1 A, TJ = 25°C 500
TPS76828 IO = 1 A, TJ = −40°C to 125°C 825
TPS76830
IO = 1 A, TJ = 25°C 450
Dropout volta
g
eTPS76830 IO = 1 A, TJ = −40°C to 125°C 675
mV
Dropout
voltage
(see Note 4)
TPS76833
IO = 1 A, TJ = 25°C 350 mV
TPS76833 IO = 1 A, TJ = −40°C to 125°C 575
TPS76850
IO = 1 A, TJ = 25°C 230
TPS76850 IO = 1 A, TJ = −40°C to 125°C 380
NOTE 4: IN voltage equals VO(typ) − 100 mV; TPS76801 output voltage set to 3.3 V nominal with external resistor divider. TPS76815, TPS76818,
TPS76825, and TPS76827 dropout voltage limited by input voltage range limitations (i.e., TPS76830 input voltage needs to drop to
2.9 V for purpose of this test).
TYPICAL CHARACTERISTICS
Table of Graphs
FIGURE
V
vs Output current 2, 3, 4
VOOutput voltage vs Free-air temperature 5, 6, 7
Ground current vs Free-air temperature 8, 9
Power supply ripple rejection vs Frequency 10
Output spectral noise density vs Frequency 11
Input voltage (min) vs Output voltage 12
ZoOutput impedance vs Frequency 13
VDO Dropout voltage vs Free-air temperature 14
Line transient response 15, 17
Load transient response 16, 18
VOOutput voltage vs Time 19
Dropout voltage vs Input voltage 20
Equivalent series resistance (ESR) vs Output current 22 − 25
TPS76815-Q1, TPS76818-Q1, TPS76825-Q1, TPS76827-Q1
TPS76828-Q1, TPS76830-Q1 TPS76833-Q1, TPS76850-Q1, TPS76801-Q1
FAST-TRANSIENT-RESPONSE 1-A LOW-DROPOUT VOLTAGE REGULATORS
SGLS155A − FEBRUARY 2003 − REVISED SEPTEMBER 2008
8POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 2
IO − Output Current − A
TPS76833
OUTPUT VOLTAGE
vs
OUTPUT CURRENT
3.2830
3.2815
3.2800
0.1 0.3
3.2825
3.2820
3.2810
0.2 0.8 1
3.2835
0 0.9
− Output Voltage − V
VO
3.2805
0.4 0.5 0.6 0.7
VI = 4.3 V
TA = 25°C
Figure 3
IO − Output Current − A
1.4975
1.4960
1.4950
1.4970
1.4965
1.4955
1.4985
− Output Voltage − V
VO
TPS76815
OUTPUT VOLTAGE
vs
OUTPUT CURRENT
1.4980
0.1 0.30.2 0.8 10 0.90.4 0.5 0.6 0.7
VI = 2.7 V
TA = 25°C
Figure 4
IO − Output Current − A
TPS76825
OUTPUT VOLTAGE
vs
OUTPUT CURRENT
2.4955
2.4940
2.4920
0.1 0.3
2.4950
2.4945
2.4935
0.2 0.4 0.6
2.4960
0 0.5
− Output Voltage − V
VO
VI = 3.5 V
TA = 25°C
2.4930
2.4925
0.80.7 0.9 1
Figure 5
TA − Free-Air Temperature − °C
TPS76833
OUTPUT VOLTAGE
vs
FREE-AIR TEMPERATURE
− Output Voltage − V
VO
3.31
3.28
3.25
−40 0
3.30
3.29
3.27
−20 100 140
3.32
−60 120
3.26
20 40 60 80
VI = 4.3 V
IO = 1 A
IO = 1 mA
TPS76815-Q1, TPS76818-Q1, TPS76825-Q1, TPS76827-Q1
TPS76828-Q1, TPS76830-Q1 TPS76833-Q1, TPS76850-Q1, TPS76801-Q1
FAST-TRANSIENT-RESPONSE 1-A LOW-DROPOUT VOLTAGE REGULATORS
SGLS155A − FEBRUARY 2003 − REVISED SEPTEMBER 2008
9
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 6
TA − Free-Air Temperature − °C
TPS76815
OUTPUT VOLTAGE
vs
FREE-AIR TEMPERATURE
− Output Voltage − V
VO
1.515
1.500
1.485
−40 0
1.510
1.505
1.495
−20 100−60 120
1.490
20 40 60 80
VI = 2.7 V
IO = 1 A
IO = 1 mA
140
Figure 7
TA − Free-Air Temperature − °C
TPS76825
OUTPUT VOLTAGE
vs
FREE-AIR TEMPERATURE
− Output Voltage − V
VO
−40 0−20 100−60 12020 40 60 80
2.515
2.500
2.480
2.510
2.505
2.495
2.490
2.485
VI = 3.5 V
IO = 1 A
IO = 1 mA
TA − Free-Air Temperature − °C
TPS76833
GROUND CURRENT
vs
FREE-AIR TEMPERATURE
Ground Current − Aµ
92
84
72
90
88
82
80
78
76
74
86
−40 0−20 100−60 12020 40 60 80 140
VI = 4.3 V
IO = 500 mA
IO = 1 A
IO = 1 mA
Figure 8
TPS76815-Q1, TPS76818-Q1, TPS76825-Q1, TPS76827-Q1
TPS76828-Q1, TPS76830-Q1 TPS76833-Q1, TPS76850-Q1, TPS76801-Q1
FAST-TRANSIENT-RESPONSE 1-A LOW-DROPOUT VOLTAGE REGULATORS
SGLS155A − FEBRUARY 2003 − REVISED SEPTEMBER 2008
10 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 9
TA − Free-Air Temperature − °C
TPS76815
GROUND CURRENT
vs
FREE-AIR TEMPERATURE
Ground Current − Aµ
−40 0−20 100−60 12020 40 60 80 140
VI = 2.7 V
IO = 1 A
100
95
90
85
80
75
IO = 1 mA
IO = 500 mA
100k10k
PSRR − Power Supply Ripple Rejection − dB
f − Frequency − Hz
POWER SUPPLY RIPPLE REJECTION
vs
FREQUENCY
70
60
50
40
30
20
10
0
−10
TPS76833
90
80
1k10010 1M
VI = 4.3 V
Co = 10 µF
IO = 1 A
TA = 25°C
Figure 10
TPS76833
OUTPUT SPECTRAL NOISE DENSITY
vs
FREQUENCY
f − Frequency − Hz
102103104105
10−5
10−6
10−8
10−7
IO = 7 mA
IO = 1 A
VI = 4.3 V
Co = 10 µF
TA = 25°C
V HzOutput Spectral Noise Density − µ
Figure 11
TPS76815-Q1, TPS76818-Q1, TPS76825-Q1, TPS76827-Q1
TPS76828-Q1, TPS76830-Q1 TPS76833-Q1, TPS76850-Q1, TPS76801-Q1
FAST-TRANSIENT-RESPONSE 1-A LOW-DROPOUT VOLTAGE REGULATORS
SGLS155A − FEBRUARY 2003 − REVISED SEPTEMBER 2008
11
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 12
3
2.7
2
1.5 1.75 2 2.25 2.5 2.75
− Input Voltage (Min) − V
INPUT VOLTAGE (MIN)
vs
OUTPUT VOLTAGE
4
3 3.25 3.5
TA = 25°C
VI
VO − Output Voltage − V
IO = 1 A
TA = 125°C
TA = −40°C
Figure 13
f − Frequency − kHz
− Output Impedance −ZoΩ
101102105106
0
10−1
10−2
104
103
IO = 1 mA
IO = 1 A
VI = 4.3 V
Co = 10 µF
TA = 25°C
TPS76833
OUTPUT IMPEDANCE
vs
FREQUENCY
Figure 14
TA − Free-Air Temperature − °C
−40 0 20 120
103
−60 40 60 80 100
− Dropout Voltage − mV
VDO
TPS76833
DROPOUT VOLTAGE
vs
FREE-AIR TEMPERATURE
102
101
100
10−1
10−2
−20 140
IO = 1 A
IO = 10 mA
IO = 0
Co = 10 µF
TPS76815-Q1, TPS76818-Q1, TPS76825-Q1, TPS76827-Q1
TPS76828-Q1, TPS76830-Q1 TPS76833-Q1, TPS76850-Q1, TPS76801-Q1
FAST-TRANSIENT-RESPONSE 1-A LOW-DROPOUT VOLTAGE REGULATORS
SGLS155A − FEBRUARY 2003 − REVISED SEPTEMBER 2008
12 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 15
VO− Change in
10
0
3.7
2.7
TPS76815
LINE TRANSIENT RESPONSE
VI
t − Time − µs
0604020 80 100 140120 160 180 200
− Input Voltage − V
∆
Output Voltage − mV
Co = 10 µF
TA = 25°C
−10
Figure 16
t − Time − µs
TPS76815
LOAD TRANSIENT RESPONSE
I − Output Current − A
O
VO− Change in∆
Output Voltage − mV
Co = 10 µF
TA = 25°C
1
0.5
0
0 300200100 400 500 700600 800 900 1000
0
50
100
−50
−100
Figure 17
TPS76833
LINE TRANSIENT RESPONSE
t − Time − µs
VO− Change in VI− Input Voltage − V
∆
Output Voltage − mV
5.3
604020 80 100 140120 160 180 200
Co = 10 µF
TA = 25°C
0
4.3
10
0
−10
Figure 18
t − Time − µs
TPS76833
LOAD TRANSIENT RESPONSE
I − Output Current − A
O
VO− Change in∆
Output Voltage − mV
1
0.5
300200100 400 500 700600 800 900 1000
0
Co = 10 µF
TA = 25°C
0
0
50
100
−50
−100
TPS76815-Q1, TPS76818-Q1, TPS76825-Q1, TPS76827-Q1
TPS76828-Q1, TPS76830-Q1 TPS76833-Q1, TPS76850-Q1, TPS76801-Q1
FAST-TRANSIENT-RESPONSE 1-A LOW-DROPOUT VOLTAGE REGULATORS
SGLS155A − FEBRUARY 2003 − REVISED SEPTEMBER 2008
13
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 19
t − Time − ms
TPS76833
OUTPUT VOLTAGE
vs
TIME (AT STARTUP)
3
2
0.30.20.1 0.4 0.5 0.70.6 0.8 0.9 10
VO− Output Voltage − V
0
1
4
Enable Pulse − V
Co = 10 µF
IO = 1 A
TA = 25°C
Figure 20
VI − Input Voltage − V
600
300
0
34
500
400
200
3.52.5
− Dropout Voltage − mV
100
4.5 5
VDO
900
800
700
TA = 125°C
TA = −40°C
TA = 25°C
IO = 1 A
TPS76801
DROPOUT VOLTAGE
vs
INPUT VOLTAGE
IN
EN
OUT
+
GND
Co
ESR
RL
VITo Load
Figure 21. Test Circuit for Typical Regions of Stability (Figures 22 through 25) (Fixed Output Options)
TPS76815-Q1, TPS76818-Q1, TPS76825-Q1, TPS76827-Q1
TPS76828-Q1, TPS76830-Q1 TPS76833-Q1, TPS76850-Q1, TPS76801-Q1
FAST-TRANSIENT-RESPONSE 1-A LOW-DROPOUT VOLTAGE REGULATORS
SGLS155A − FEBRUARY 2003 − REVISED SEPTEMBER 2008
14 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 22
0.10 200 400 600 800 1000
TYPICAL REGION OF STABILITY
EQUIVALENT SERIES RESISTANCE†
vs
OUTPUT CURRENT
10
IO − Output Current − mA
ESR − Equivalent Series Resistance − Ω
1
VO = 3.3 V
Co = 4.7 µF
VI = 4.3 V
TA = 25°C
Region of Stability
Region of Instability
Figure 23
TYPICAL REGION OF STABILITY
EQUIVALENT SERIES RESISTANCE†
vs
OUTPUT CURRENT
IO − Output Current − mA
ESR − Equivalent Series Resistance − Ω
0.10 200 400 600 800 1000
10
1
VO = 3.3 V
Co = 4.7 µF
VI = 4.3 V
TJ = 125°C
Region of Stability
Region of Instability
Figure 24
0.10 200 400 600 800 1000
TYPICAL REGION OF STABILITY
EQUIVALENT SERIES RESISTANCE†
vs
OUTPUT CURRENT
10
IO − Output Current − mA
ESR − Equivalent Series Resistance − Ω
1
Region of Instability
Region of Stability
VO = 3.3 V
Co = 22 µF
VI = 4.3 V
TA = 25°C
ESR − Equivalent Series Resistance − Ω
Figure 25
TYPICAL REGION OF STABILITY
EQUIVALENT SERIES RESISTANCE†
vs
OUTPUT CURRENT
0.10 200 400 600 800 1000
10
1
IO − Output Current − mA
VO = 3.3 V
Co= 22 µF
VI = 4.3 V
TJ = 125°C
Region of Stability
Region of Instability
†Equivalent series resistance (ESR) refers to the total series resistance, including the ESR of the capacitor, any series resistance added
externally, and PWB trace resistance to Co.
TPS76815-Q1, TPS76818-Q1, TPS76825-Q1, TPS76827-Q1
TPS76828-Q1, TPS76830-Q1 TPS76833-Q1, TPS76850-Q1, TPS76801-Q1
FAST-TRANSIENT-RESPONSE 1-A LOW-DROPOUT VOLTAGE REGULATORS
SGLS155A − FEBRUARY 2003 − REVISED SEPTEMBER 2008
15
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
APPLICATION INFORMATION
The TPS768xx family includes eight fixed-output voltage regulators (1.5 V, 1.8 V, 2.5 V, 2.7 V, 2.8 V, 3.0 V,
3.3 V, and 5.0 V), and offers an adjustable device, the TPS76801 (adjustable from 1.2 V to 5.5 V).
device operation
The TPS768xx features very low quiescent current, which remains virtually constant even with varying loads.
Conventional LDO regulators use a pnp pass element, the base current of which is directly proportional to the
load current through the regulator (IB = IC/β). The TPS768xx uses a PMOS transistor to pass current; because
the gate of the PMOS is voltage driven, operating current is low and invariable over the full load range.
Another pitfall associated with the pnp-pass element is its tendency to saturate when the device goes into
dropout. The resulting drop in β forces an increase in IB to maintain the load. During power up, this translates
to large start-up currents. Systems with limited supply current may fail to start up. In battery-powered systems,
it means rapid battery discharge when the voltage decays below the minimum required for regulation. The
TPS768xx quiescent current remains low even when the regulator drops out, eliminating both problems.
The TPS768xx family also features a shutdown mode that places the output in the high-impedance state
(essentially equal to the feedback-divider resistance) and reduces quiescent current to 2 µA. If the shutdown
feature is not used, EN should be tied to ground.
minimum load requirements
The TPS768xx family is stable even at zero load; no minimum load is required for operation.
FB - pin connection (adjustable version only)
The FB pin is an input pin to sense the output voltage and close the loop for the adjustable option. The output
voltage is sensed through a resistor divider network to close the loop as shown in Figure 27. Normally, this
connection should be as short as possible; however, the connection can be made near a critical circuit to
improve performance at that point. Internally, FB connects to a high-impedance wide-bandwidth amplifier and
noise pickup feeds through to the regulator output. Routing the FB connection to minimize/avoid noise pickup
is essential.
external capacitor requirements
An input capacitor is not usually required; however, a ceramic bypass capacitor (0.047 µF or larger) improves
load transient response and noise rejection if the TPS768xx is located more than a few inches from the power
supply. A higher-capacitance electrolytic capacitor may be necessary if large (hundreds of milliamps) load
transients with fast rise times are anticipated.
Like all low dropout regulators, the TPS768xx requires an output capacitor connected between OUT and GND
to stabilize the internal control loop. The minimum recommended capacitance value is 10 µF and the ESR
(equivalent series resistance) must be between 50 mΩ and 1.5 Ω. Capacitor values 10 µF or larger are
acceptable, provided the ESR is less than 1.5 Ω. Solid tantalum electrolytic, aluminum electrolytic, and
multilayer ceramic capacitors are all suitable, provided they meet the requirements described above. Most of
the commercially available 10 µF surface-mount ceramic capacitors, including devices from Sprague and
Kemet, meet the ESR requirements stated above.
TPS76815-Q1, TPS76818-Q1, TPS76825-Q1, TPS76827-Q1
TPS76828-Q1, TPS76830-Q1 TPS76833-Q1, TPS76850-Q1, TPS76801-Q1
FAST-TRANSIENT-RESPONSE 1-A LOW-DROPOUT VOLTAGE REGULATORS
SGLS155A − FEBRUARY 2003 − REVISED SEPTEMBER 2008
16 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
APPLICATION INFORMATION
external capacitor requirements (continued)
PG
OUT
OUT
7
6
5
IN
IN
EN
GND
3
16
14
13
VI
C1
0.1 µF
PG
VO
10 µF
+
TPS768xx
Co
250 kΩ
Figure 26. Typical Application Circuit (Fixed Versions)
programming the TPS76801 adjustable LDO regulator
The output voltage of the TPS76801 adjustable regulator is programmed using an external resistor divider as
shown in Figure 27. The output voltage is calculated using:
VO+Vref ǒ1)R1
R2Ǔ(1
)
Where:
Vref = 1.1834 V typ (the internal reference voltage)
Resistors R1 and R2 should be chosen for approximately 50-µA divider current. Lower value resistors can be
used but offer no inherent advantage and waste more power. Higher values should be avoided as leakage
currents at FB increase the output voltage error. The recommended design procedure is to choose
R2 = 30.1 kΩ to set the divider current at 50 µA and then calculate R1 using:
R1 +ǒVO
Vref *1Ǔ R2 (2)
OUTPUT
VOLTAGE R1 R2
2.5 V
3.3 V
3.6 V
4.75 V
UNIT
33.2
53.6
61.9
90.8
30.1
30.1
30.1
30.1
kΩ
kΩ
kΩ
kΩ
OUTPUT VOLTAGE
PROGRAMMING GUIDE
VO
VIPG
OUT
FB / NC
R1
R2
GND
EN
IN
≤0.9 V
≥1.7 V
TPS76801
PG
0.1 µF
250 kΩ
Figure 27. TPS76801 Adjustable LDO Regulator Programming
TPS76815-Q1, TPS76818-Q1, TPS76825-Q1, TPS76827-Q1
TPS76828-Q1, TPS76830-Q1 TPS76833-Q1, TPS76850-Q1, TPS76801-Q1
FAST-TRANSIENT-RESPONSE 1-A LOW-DROPOUT VOLTAGE REGULATORS
SGLS155A − FEBRUARY 2003 − REVISED SEPTEMBER 2008
17
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
APPLICATION INFORMATION
power-good indicator
The TPS768xx features a power-good (PG) output that can be used to monitor the status of the regulator. The
internal comparator monitors the output voltage: when the output drops to between 92% and 98% of its nominal
regulated value, the PG output transistor turns on, taking the signal low. The open-drain output requires a pullup
resistor. If not used, it can be left floating. PG can be used to drive power-on reset circuitry or used as a
low-battery indicator. PG does not assert itself when the regulated output voltage falls out of the specified 2%
tolerance, but instead reports an output voltage low, relative to its nominal regulated value.
regulator protection
The TPS768xx PMOS-pass transistor has a built-in back diode that conducts reverse currents when the input
voltage drops below the output voltage (e.g., during power down). Current is conducted from the output to the
input and is not internally limited. When extended reverse voltage is anticipated, external limiting may be
appropriate.
The TPS768xx also features internal current limiting and thermal protection. During normal operation, the
TPS768xx limits output current to approximately 1.7 A. When current limiting engages, the output voltage scales
back linearly until the overcurrent condition ends. While current limiting is designed to prevent gross device
failure, care should be taken not to exceed the power dissipation ratings of the package. If the temperature of
the device exceeds 150°C(typ), thermal-protection circuitry shuts it down. Once the device has cooled below
130°C(typ), regulator operation resumes.
power dissipation and junction temperature
Specified regulator operation is assured to a junction temperature of 125°C; the maximum junction temperature
should be restricted to 125°C under normal operating conditions. This restriction limits the power dissipation
the regulator can handle in any given application. To ensure the junction temperature is within acceptable limits,
calculate the maximum allowable dissipation, PD(max), and the actual dissipation, PD, which must be less than
or equal to PD(max).
The maximum-power-dissipation limit is determined using the following equation:
PD(max) +TJmax *TA
RqJA
Where:
TJmax is the maximum allowable junction temperature.
TA is the ambient temperature.
RθJA is the thermal resistance junction-to-ambient for the package, i.e., 172°C/W for the 8-terminal
SOIC and 32.6°C/W for the 20-terminal PWP with no airflow.
The regulator dissipation is calculated using:
PD+ǒVI*VOǓ IO
Power dissipation resulting from quiescent current is negligible. Excessive power dissipation will trigger the
thermal protection circuit.
PACKAGE OPTION ADDENDUM
www.ti.com 24-May-2010
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status (1) Package Type Package
Drawing Pins Package Qty Eco Plan (2) Lead/
Ball Finish MSL Peak Temp (3) Samples
(Requires Login)
TPS76801QPWPRG4Q1 ACTIVE HTSSOP PWP 20 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-3-260C-168 HR Request Free Samples
TPS76801QPWPRQ1 ACTIVE HTSSOP PWP 20 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-3-260C-168 HR Contact TI Distributor
or Sales Office
TPS76815QPWPRQ1 ACTIVE HTSSOP PWP 20 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-3-260C-168 HR Purchase Samples
TPS76818QPWPRQ1 ACTIVE HTSSOP PWP 20 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-3-260C-168 HR Request Free Samples
TPS76825QPWPRQ1 ACTIVE HTSSOP PWP 20 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-3-260C-168 HR Purchase Samples
TPS76833QPWPRQ1 ACTIVE HTSSOP PWP 20 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-3-260C-168 HR Request Free Samples
TPS76850QPWPRQ1 ACTIVE HTSSOP PWP 20 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-3-260C-168 HR Request Free Samples
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
PACKAGE OPTION ADDENDUM
www.ti.com 24-May-2010
Addendum-Page 2
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF TPS76801-Q1, TPS76815-Q1, TPS76818-Q1, TPS76825-Q1, TPS76827-Q1, TPS76828-Q1, TPS76830-Q1, TPS76833-Q1,
TPS76850-Q1 :
•Catalog: TPS76801, TPS76815, TPS76818, TPS76825, TPS76827, TPS76828, TPS76830, TPS76833, TPS76850
•Enhanced Product: TPS76801-EP, TPS76815-EP, TPS76818-EP, TPS76825-EP, TPS76833-EP, TPS76850-EP
NOTE: Qualified Version Definitions:
•Catalog - TI's standard catalog product
•Enhanced Product - Supports Defense, Aerospace and Medical Applications
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All
semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time
of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products Applications
Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive
Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications
Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers
DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps
DSP dsp.ti.com Energy and Lighting www.ti.com/energy
Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial
Interface interface.ti.com Medical www.ti.com/medical
Logic logic.ti.com Security www.ti.com/security
Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com
Wireless Connectivity www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated