DS2431
1024-Bit, 1-Wire EEPROM
________________________________________________________________
Maxim Integrated Products
1
19-4675; Rev 8; 10/09
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642,
or visit Maxim’s website at www.maxim-ic.com.
General Description
The DS2431 is a 1024-bit, 1-Wire®EEPROM chip orga-
nized as four memory pages of 256 bits each. Data is
written to an 8-byte scratchpad, verified, and then
copied to the EEPROM memory. As a special feature, the
four memory pages can individually be write protected or
put in EPROM-emulation mode, where bits can only be
changed from a 1 to a 0 state. The DS2431 communi-
cates over the single-conductor 1-Wire bus. The commu-
nication follows the standard 1-Wire protocol. Each
device has its own unalterable and unique 64-bit ROM
registration number that is factory lasered into the chip.
The registration number is used to address the device in
a multidrop, 1-Wire net environment.
Applications
Accessory/PCB Identification
Medical Sensor Calibration Data Storage
Analog Sensor Calibration Including IEEE
P1451.4 Smart Sensors
Ink and Toner Print Cartridge Identification
After-Market Management of Consumables
Features
1024 Bits of EEPROM Memory Partitioned Into
Four Pages of 256 Bits
Individual Memory Pages Can Be Permanently
Write Protected or Put in EPROM-Emulation Mode
(“Write to 0”)
Switchpoint Hysteresis and Filtering to Optimize
Performance in the Presence of Noise
IEC 1000-4-2 Level 4 ESD Protection (±8kV
Contact, ±15kV Air, Typical)
Reads and Writes Over a Wide Voltage Range
from 2.8V to 5.25V from -40°C to +85°C
Communicates to Host with a Single Digital
Signal at 15.4kbps or 125kbps Using 1-Wire
Protocol
Also Available as Automotive Version Meeting
AEC-Q100 Grade 1 Qualification Requirements
(DS2431-A1)
Ordering Information
IO
RPUP
VCC
μC
GND
DS2431
Typical Operating Circuit
Note: The leads of TO-92 packages on tape and reel are
formed to approximately 100-mil (2.54mm) spacing. For
details, refer to the package outline drawing.
+
Denotes a lead(Pb)-free/RoHS-compliant package.
T&R = Tape and reel.
*
EP = Exposed pad.
PART TEMP RANGE PIN-PACKAGE
DS2431+ -40°C to +85°C 3 TO-92
DS2431+T&R -40°C to +85°C 3 TO-92
DS2431P+ -40°C to +85°C 6 TSOC
DS2431P+T&R -40°C to +8C 6 TSOC
DS2431G+ -40°C to +8C 2 SFN
DS2431G+T&R -40°C to +8C 2 SFN
DS2431Q+T&R -40°C to +8C 6 TDFN-EP* (2.5k pcs)
DS2431X-S+ -40°C to +8C 3x3 UCSPR (2.5k pcs)
DS2431X+ -40°C to +8C 3x3 UCSPR (10k pcs)
1-Wire is a registered trademark of Maxim Integrated Products, Inc.
Pin Configurations appear at end of data sheet.
DS2431
1024-Bit, 1-Wire EEPROM
2 _______________________________________________________________________________________
ABSOLUTE MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS
(TA= -40°C to +85°C.) (Note 1)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
IO Voltage Range to GND .......................................-0.5V to +6V
IO Sink Current ...................................................................20mA
Operating Temperature Range ...........................-40°C to +85°C
Junction Temperature......................................................+150°C
Storage Temperature Range .............................-55°C to +125°C
Soldering Temperature...........................Refer to the IPC/JEDEC
J-STD-020 Specification.
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
IO PIN: GENERAL DATA
1-Wire Pullup Voltage VPUP (Note 2) 2.8 5.25 V
1-Wire Pullup Resistance RPUP (Notes 2, 3) 0.3 2.2 k
Input Capacitance CIO (Notes 4, 5) 1000 pF
Input Load Current ILIO pin at VPUP 0.05 6.7 μA
High-to-Low Switching Threshold VTL (Notes 5, 6, 7) 0.5 VPUP -
1.8 V
Input Low Voltage VIL (Notes 2, 8) 0.5 V
Low-to-High Switching Threshold VTH (Notes 5, 6, 9) 1.0 VPUP -
1.0 V
Switching Hysteresis VHY (Notes 5, 6, 10) 0.21 1.70 V
Output Low Voltage VOL At 4mA (Note 11) 0.4 V
Standard speed, RPUP = 2.2k 5
Overdrive speed, RPUP = 2.2k 2
Recovery Time
(Notes 2,12) tREC Overdrive speed, directly prior to reset
pulse; RPUP = 2.2k5
μs
Standard speed 0.5 5.0
Rising-Edge Hold-Off Time
(Notes 5, 13) tREH Overdrive speed Not applicable (0) μs
Standard speed 65
Time Slot Duration
(Notes 2, 14) tSLOT Overdrive speed 8 μs
IO PIN: 1-Wire RESET, PRESENCE-DETECT CYCLE
Standard speed 480 640
Reset Low Time (Note 2) tRSTL Overdrive speed 48 80
μs
Standard speed 15 60
Presence-Detect High Time tPDH Overdrive speed 2 6
μs
Standard speed 60 240
Presence-Detect Low Time tPDL Overdrive speed 8 24 μs
Standard speed 60 75
Presence-Detect Sample Time
(Notes 2, 15) tMSP Overdrive speed 6 10 μs
DS2431
1024-Bit, 1-Wire EEPROM
_______________________________________________________________________________________ 3
ELECTRICAL CHARACTERISTICS (continued)
(TA= -40°C to +85°C.) (Note 1)
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
IO PIN: 1-Wire WRITE
Standard speed 60 120
Overdrive speed, VPUP > 4.5V 5 15.5
Write-Zero Low Time
(Notes 2, 16, 17) tW0L
Overdrive speed 6 15.5
μs
Standard speed 1 15
Write-One Low Time
(Notes 2, 17) tW1L Overdrive speed 1 2
μs
IO PIN: 1-Wire READ
Standard speed 5 15 -
Read Low Time
(Notes 2, 18) tRL Overdrive speed 1 2 - μs
Standard speed tRL + 15
Read Sample Time
(Notes 2, 18) tMSR Overdrive speed tRL + 2 μs
EEPROM
Programming Current IPROG (Notes 5, 19) 0.8 mA
Programming Time tPROG (Notes 20, 21) 10 ms
At +25°C 200k
Write/Erase Cycles (Endurance)
(Notes 22, 23) NCY At +85°C (worst case) 50k
Data Retention
(Notes 24, 25, 26) tDR At +85°C (worst case) 40 Years
Note 1: Specifications at TA= -40°C are guaranteed by design only and not production tested.
Note 2: System requirement.
Note 3: Maximum allowable pullup resistance is a function of the number of 1-Wire devices in the system and 1-Wire recovery times.
The specified value here applies to systems with only one device and with the minimum 1-Wire recovery times. For more
heavily loaded systems, an active pullup such as that found in the DS2482-x00, DS2480B, or DS2490 may be required.
Note 4: Maximum value represents the internal parasite capacitance when VPUP is first applied. If a 2.2kΩresistor is used to pull
up the data line, 2.5µs after VPUP has been applied, the parasite capacitance does not affect normal communications.
Note 5: Guaranteed by design, characterization, and/or simulation only. Not production tested.
Note 6: VTL, VTH, and VHY are a function of the internal supply voltage, which is a function of VPUP, RPUP, 1-Wire timing, and
capacitive loading on IO. Lower VPUP, higher RPUP, shorter tREC, and heavier capacitive loading all lead to lower values of
VTL, VTH, and VHY.
Note 7: Voltage below which, during a falling edge on IO, a logic 0 is detected.
Note 8: The voltage on IO must be less than or equal to VILMAX at all times the master is driving IO to a logic 0 level.
Note 9: Voltage above which, during a rising edge on IO, a logic 1 is detected.
Note 10: After VTH is crossed during a rising edge on IO, the voltage on IO must drop by at least VHY to be detected as logic 0.
Note 11: The I-V characteristic is linear for voltages less than 1V.
Note 12: Applies to a single device attached to a 1-Wire line.
Note 13: The earliest recognition of a negative edge is possible at tREH after VTH has been reached on the preceding rising edge.
Note 14: Defines maximum possible bit rate. Equal to tW0LMIN + tRECMIN.
Note 15: Interval after tRSTL during which a bus master is guaranteed to sample a logic 0 on IO if there is a DS2431 present.
Minimum limit is tPDHMAX; maximum limit is tPDHMIN + tPDLMIN.
Note 16: Numbers in bold are not in compliance with legacy 1-Wire product standards. See the
Comparison Table
.
Note 17: εin Figure 11 represents the time required for the pullup circuitry to pull the voltage on IO up from VIL to VTH. The actual
maximum duration for the master to pull the line low is tW1LMAX + tF- εand tW0LMAX + tF- ε, respectively.
Note 18: δin Figure 11 represents the time required for the pullup circuitry to pull the voltage on IO up from VIL to the input-high
threshold of the bus master. The actual maximum duration for the master to pull the line low is tRLMAX + tF.
Note 19: Current drawn from IO during the EEPROM programming interval. The pullup circuit on IO during the programming interval
should be such that the voltage at IO is greater than or equal to VPUPMIN. If VPUP in the system is close to VPUPMIN, a low-
impedance bypass of RPUP, which can be activated during programming, may need to be added.
Note 20: Interval begins tREHMAX after the trailing rising edge on IO for the last time slot of the E/S byte for a valid Copy Scratchpad
sequence. Interval ends once the device’s self-timed EEPROM programming cycle is complete and the current drawn by
the device has returned from IPROG to IL.
Note 21: tPROG for units branded version “A1” is 12.5ms. tPROG for units branded version “A2” and later is 10ms.
Note 22: Write-cycle endurance is degraded as TAincreases.
Note 23: Not 100% production tested; guaranteed by reliability monitor sampling.
Note 24: Data retention is degraded as TAincreases.
Note 25: Guaranteed by 100% production test at elevated temperature for a shorter time; equivalence of this production test to the
data sheet limit at operating temperature range is established by reliability testing.
Note 26: EEPROM writes can become nonfunctional after the data-retention time is exceeded. Long-term storage at elevated tem-
peratures is not recommended; the device can lose its write capability after 10 years at +125°C or 40 years at +85°C.
COMPARISON TABLE
LEGACY VALUES DS2431 VALUES
STANDARD SPEED
s)
OVERDRIVE SPEED
s)
STANDARD SPEED
s)
OVERDRIVE SPEED
s)
PARAMETER
MIN MAX MIN MAX MIN MAX MIN MAX
tSLOT (including tREC) 61 (undefined) 7 (undefined) 65* (undefined) 8* (undefined)
tRSTL 480 (undefined) 48 80 480 640 48 80
tPDH 15 60 2 6 15 60 2 6
tPDL 60 240 8 24 60 240 8 24
tW0L 60 120 6 16 60 120 6 15.5
DS2431
1024-Bit, 1-Wire EEPROM
4 _______________________________________________________________________________________
*
Intentional change; longer recovery time requirement due to modified 1-Wire front-end.
Note: Numbers in bold are not in compliance with legacy 1-Wire product standards.
Pin Description
PIN
TSOC TO-92 TDFN-EP SFN UCSPR NAME FUNCTION
3, 4, 5, 6 3 1, 4, 5, 6 A2, A3, C2,
C3 N.C. Not Connected
2 2 2 1 C1 IO
1-Wire Bus Interface. Open-drain signal
that requires an external pullup resistor.
1 1 3 2 A1 GND Ground Reference
— — EP EP
Exposed Pad. Solder evenly to the
board’s ground plane for proper
operation. Refer to Application Note
3273: Exposed Pads: A Brief
Introduction for additional information.
DS2431
1024-Bit, 1-Wire EEPROM
_______________________________________________________________________________________ 5
Detailed Description
The DS2431 combines 1024 bits of EEPROM, an
8-byte register/control page with up to 7 user read/write
bytes, and a fully featured 1-Wire interface in a single
chip. Each DS2431 has its own 64-bit ROM registration
number that is factory lasered into the chip to provide a
guaranteed unique identity for absolute traceability.
Data is transferred serially through the
1-Wire protocol, which requires only a single data lead
and a ground return. The DS2431 has an additional
memory area called the scratchpad that acts as a
buffer when writing to the main memory or the register
page. Data is first written to the scratchpad from which
it can be read back. After the data has been verified, a
Copy Scratchpad command transfers the data to its
final memory location. The DS2431 applications include
accessory/PCB identification, medical sensor calibra-
tion data storage, analog sensor calibration including
IEEE P1451.4 smart sensors, ink and toner print car-
tridge identification, and after-market management of
consumables.
Overview
The block diagram in Figure 1 shows the relationships
between the major control and memory sections of the
DS2431. The DS2431 has four main data components:
64-bit lasered ROM, 64-bit scratchpad, four 32-byte
pages of EEPROM, and a 64-bit register page.
MEMORY
FUNCTION
CONTROL UNIT
DATA MEMORY
4 PAGES OF
256 BITS EACH
CRC-16
GENERATOR
64-BIT
SCRATCHPAD
1-Wire
FUNCTION CONTROL
64-BIT
LASERED ROM
PARASITE POWER
IO
REGISTER PAGE
64 BITS
DS2431
Figure 1. Block Diagram
DS2431
1024-Bit, 1-Wire EEPROM
6 _______________________________________________________________________________________
The hierarchical structure of the 1-Wire protocol is
shown in Figure 2. The bus master must first provide
one of the seven ROM function commands: Read ROM,
Match ROM, Search ROM, Skip ROM, Resume,
Overdrive-Skip ROM, or Overdrive-Match ROM. Upon
completion of an Overdrive-Skip ROM or Overdrive-
Match ROM command byte executed at standard
speed, the device enters overdrive mode where all
subsequent communication occurs at a higher speed.
The protocol required for these ROM function com-
mands is described in Figure 9. After a ROM function
command is successfully executed, the memory func-
tions become accessible and the master can provide
any one of the four memory function commands. The
protocol for these memory function commands is
described in Figure 7. All data is read and written
least significant bit first.
64-Bit Lasered ROM
Each DS2431 contains a unique ROM code that is 64
bits long. The first 8 bits are a 1-Wire family code. The
next 48 bits are a unique serial number. The last 8 bits
are a cyclic redundancy check (CRC) of the first 56 bits.
See Figure 3 for details. The 1-Wire CRC is generated
using a polynomial generator consisting of a shift regis-
ter and XOR gates as shown in Figure 4. The polynomial
is X8+ X5+ X4+ 1. Additional information about the
1-Wire CRC is available in Application Note 27:
Understanding and Using Cyclic Redundancy Checks
with Maxim iButton
®
Products
.
The shift register bits are initialized to 0. Then, starting
with the least significant bit of the family code, one bit
at a time is shifted in. After the 8th bit of the family code
has been entered, the serial number is entered. After
the last bit of the serial number has been entered, the
shift register contains the CRC value. Shifting in the 8
bits of the CRC returns the shift register to all 0s.
DS2431 COMMAND LEVEL:
AVAILABLE COMMANDS: DATA FIELD AFFECTED:
READ ROM
MATCH ROM
SEARCH ROM
SKIP ROM
RESUME
OVERDRIVE-SKIP ROM
OVERDRIVE-MATCH ROM
64-BIT REG. #, RC-FLAG
64-BIT REG. #, RC-FLAG
64-BIT REG. #, RC-FLAG
RC-FLAG
RC-FLAG
RC-FLAG, OD-FLAG
64-BIT REG. #, RC-FLAG, OD-FLAG
1-Wire ROM FUNCTION COMMANDS
(SEE FIGURE 9)
WRITE SCRATCHPAD
READ SCRATCHPAD
COPY SCRATCHPAD
READ MEMORY
64-BIT SCRATCHPAD, FLAGS
64-BIT SCRATCHPAD
DATA MEMORY, REGISTER PAGE
DATA MEMORY, REGISTER PAGE
DS2431-SPECIFIC
MEMORY FUNCTION COMMANDS
(SEE FIGURE 7)
Figure 2. Hierarchical Structure for 1-Wire Protocol
MSB
8-BIT
CRC CODE 48-BIT SERIAL NUMBER
MSB MSBLSB
LSB
LSB
8-BIT FAMILY CODE
(2Dh)
MSBLSB
Figure 3. 64-Bit Lasered ROM
iButton is a registered trademark of Maxim Integrated Products, Inc.
DS2431
1024-Bit, 1-Wire EEPROM
_______________________________________________________________________________________ 7
Memory Access
Data memory and registers are located in a linear
address space, as shown in Figure 5. The data memory
and the registers have unrestricted read access. The
DS2431 EEPROM array consists of 18 rows of 8 bytes
each. The first 16 rows are divided equally into four
memory pages (32 bytes each). These four pages are
the primary data memory. Each page can be individu-
ally set to open (unprotected), write protected, or
EPROM mode by setting the associated protection byte
in the register row. The last two rows contain protection
registers and reserved bytes. The register row consists
of 4 protection control bytes, a copy-protection byte,
the factory byte, and 2 user byte/manufacture ID bytes.
The manufacturer ID can be a customer-supplied iden-
tification code that assists the application software in
identifying the product the DS2431 is associated with.
1ST
STAGE
2ND
STAGE
3RD
STAGE
4TH
STAGE
7TH
STAGE
8TH
STAGE
6TH
STAGE
5TH
STAGE
X0X1X2X3X4
POLYNOMIAL = X8 + X5 + X4 + 1
INPUT DATA
X5X6X7X8
Figure 4. 1-Wire CRC Generator
ADDRESS RANGE TYPE DESCRIPTION PROTECTION CODES
0000h to 001Fh R/(W) Data Memory Page 0
0020h to 003Fh R/(W) Data Memory Page 1
0040h to 005Fh R/(W) Data Memory Page 2
0060h to 007Fh R/(W) Data Memory Page 3
0080h* R/(W) Protection Control Byte Page 0 55h: Write Protect P0; AAh: EPROM Mode P0;
55h or AAh: Write Protect 80h
0081h* R/(W) Protection Control Byte Page 1 55h: Write Protect P1; AAh: EPROM Mode P1;
55h or AAh: Write Protect 81h
0082h* R/(W) Protection Control Byte Page 2 55h: Write Protect P2; AAh: EPROM Mode P2;
55h or AAh: Write Protect 82h
0083h* R/(W) Protection Control Byte Page 3 55h: Write Protect P3; AAh: EPROM Mode P3;
55h or AAh: Write Protect 83h
0084h* R/(W) Copy Protection Byte 55h or AAh: Copy Protect 0080h:008Fh, and Any
Write-Protected Pages
0085h R Factory Byte. Set at Factory. AAh: Write Protect 85h, 86h, 87h;
55h: Write Protect 85h; Unprotect 86h, 87h
0086h R/(W) User Byte/Manufacturer ID
0087h R/(W) User Byte/Manufacturer ID
0088h to 008Fh Reserved
Figure 5. Memory Map
*
Once programmed to AAh or 55h this address becomes read only. All other codes can be stored, but neither write protect the
address nor activate any function.
DS2431
1024-Bit, 1-Wire EEPROM
8 _______________________________________________________________________________________
Contact the factory to set up and register a custom
manufacturer ID. The last row is reserved for future use.
It is undefined in terms of R/W functionality and should
not be used.
In addition to the main EEPROM array, an 8-byte
volatile scratchpad is included. Writes to the EEPROM
array are a two-step process. First, data is written to the
scratchpad and then copied into the main array. This
allows the user to first verify the data written to the
scratchpad prior to copying into the main array. The
device only supports full row (8-byte) copy operations.
For data in the scratchpad to be valid for a copy opera-
tion, the address supplied with a Write Scratchpad
command must start on a row boundary, and 8 full
bytes must be written into the scratchpad.
The protection control registers determine how incom-
ing data on a Write Scratchpad command is loaded
into the scratchpad. A protection setting of 55h (write
protect) causes the incoming data to be ignored and
the target address main memory data to be loaded into
the scratchpad. A protection setting of AAh (EPROM
mode) causes the logical AND of incoming data and
target address main memory data to be loaded into the
scratchpad. Any other protection control register set-
ting leaves the associated memory page open for unre-
stricted write access. Protection-control byte settings of
55h or AAh also write protect the protection-control
byte. The protection-control byte setting of 55h does
not block the copy. This allows write-protected data to
be refreshed (i.e., reprogrammed with the current data)
in the device.
The copy-protection byte is used for a higher level of
security and should only be used after all other protec-
tion control bytes, user bytes, and write-protected
pages are set to their final value. If the copy-protection
byte is set to 55h or AAh, all copy attempts to the regis-
ter row and user-byte row are blocked. In addition, all
copy attempts to write-protected main memory pages
(i.e., refresh) are blocked.
Address Registers and Transfer Status
The DS2431 employs three address registers: TA1, TA2,
and E/S (Figure 6). These registers are common to
many other 1-Wire devices but operate slightly different-
ly with the DS2431. Registers TA1 and TA2 must be
loaded with the target address to which the data is writ-
ten or from which data is read. Register E/S is a read-
only transfer-status register used to verify data integrity
with write commands. E/S bits E[2:0] are loaded with the
incoming T[2:0] on a Write Scratchpad command and
increment on each subsequent data byte. This is, in
effect, a byte-ending offset counter within the 8-byte
scratchpad. Bit 5 of the E/S register, called PF, is a logic
1 if the data in the scratchpad is not valid due to a loss
of power or if the master sends fewer bytes than needed
to reach the end of the scratchpad. For a valid write to
the scratchpad, T[2:0] must be 0 and the master must
have sent 8 data bytes. Bits 3, 4, and 6 have no func-
tion; they always read 0. The highest valued bit of the
E/S register, called authorization accepted (AA), acts as
a flag to indicate that the data stored in the scratchpad
has already been copied to the target memory address.
Writing data to the scratchpad clears this flag.
Writing with Verification
To write data to the DS2431, the scratchpad must be
used as intermediate storage. First, the master issues
the Write Scratchpad command to specify the desired
target address, followed by the data to be written to the
scratchpad. Note that Copy Scratchpad commands
must be performed on 8-byte boundaries, i.e., the three
BIT # 7 6 5 4 3 2 1 0
TARGET ADDRESS (TA1) T7 T6 T5 T4 T3 T2 T1 T0
TARGET ADDRESS (TA2) T15 T14 T13 T12 T11 T10 T9 T8
ENDING ADDRESS WITH
DATA STATUS (E/S)
(READ ONLY)
AA 0 PF 0 0 E2 E1 E0
Figure 6. Address Registers
DS2431
1024-Bit, 1-Wire EEPROM
_______________________________________________________________________________________ 9
LSBs of the target address (T2, T1, T0) must be equal
to 000b. If T[2:0] are sent with nonzero values, the copy
function is blocked. Under certain conditions (see the
Write Scratchpad [0Fh]
section) the master receives an
inverted CRC-16 of the command, address (actual
address sent), and data at the end of the Write
Scratchpad command sequence. Knowing this CRC
value, the master can compare it to the value it has cal-
culated to decide if the communication was successful
and proceed to the Copy Scratchpad command. If the
master could not receive the CRC-16, it should send
the Read Scratchpad command to verify data integrity.
As a preamble to the scratchpad data, the DS2431
repeats the target address TA1 and TA2 and sends the
contents of the E/S register. If the PF flag is set, data
did not arrive correctly in the scratchpad, or there was
a loss of power since data was last written to the
scratchpad. The master does not need to continue
reading; it can start a new trial to write data to the
scratchpad. Similarly, a set AA flag together with a
cleared PF flag indicates that the device did not recog-
nize the Write command.
If everything went correctly, both flags are cleared.
Now the master can continue reading and verifying
every data byte. After the master has verified the data,
it can send the Copy Scratchpad command, for exam-
ple. This command must be followed exactly by the
data of the three address registers, TA1, TA2, and E/S.
The master should obtain the contents of these regis-
ters by reading the scratchpad.
Memory Function Commands
The
Memory Function Flowchart
(Figure 7) describes
the protocols necessary for accessing the memory of
the DS2431. An example on how to use these functions
to write to and read from the device is in the
Memory
Function Example
section. The communication
between the master and the DS2431 takes place either
at standard speed (default, OD = 0) or at overdrive
speed (OD = 1). If not explicitly set into overdrive
mode, the DS2431 assumes standard speed.
Write Scratchpad [0Fh]
The Write Scratchpad command applies to the data
memory and the writable addresses in the register
page. For the scratchpad data to be valid for copying
to the array, the user must perform a Write Scratchpad
command of 8 bytes starting at a valid row boundary.
The Write Scratchpad command accepts invalid
addresses and partial rows, but subsequent Copy
Scratchpad commands are blocked.
After issuing the Write Scratchpad command, the mas-
ter must first provide the 2-byte target address, fol-
lowed by the data to be written to the scratchpad. The
data is written to the scratchpad starting at the byte off-
set of T[2:0]. The E/S bits E[2:0] are loaded with the
starting byte offset and increment with each subse-
quent byte. Effectively, E[2:0] is the byte offset of the
last full byte written to the scratchpad. Only full data
bytes are accepted.
When executing the Write Scratchpad command, the
CRC generator inside the DS2431 (Figure 13) calcu-
lates a CRC of the entire data stream, starting at the
command code and ending at the last data byte as
sent by the master. This CRC is generated using the
CRC-16 polynomial by first clearing the CRC generator
and then shifting in the command code (0Fh) of the
Write Scratchpad command, the target addresses (TA1
and TA2), and all the data bytes. Note that the CRC-16
calculation is performed with the actual TA1 and TA2
and data sent by the master. The master can end the
Write Scratchpad command at any time. However, if
the end of the scratchpad is reached (E[2:0] = 111b),
the master can send 16 read time slots and receive the
CRC generated by the DS2431.
If a Write Scratchpad command is attempted to a write-
protected location, the scratchpad is loaded with the
data already existing in memory rather than the data
transmitted. Similarly, if the target address page is in
EPROM mode, the scratchpad is loaded with the bit-
wise logical AND of the transmitted data and data
already existing in memory.
DS2431
1024-Bit, 1-Wire EEPROM
10 ______________________________________________________________________________________
BUS MASTER Tx MEMORY
FUNCTION COMMAND
BUS MASTER Tx
TA1 (T[7:0]), TA2 (T[15:8])
BUS MASTER Rx
TA1 (T[7:0]), TA2 (T[15:8]),
AND E/S BYTE
BUS MASTER Rx
DATA BYTE FROM
SCRATCHPAD
MASTER Tx DATA BYTE
TO SCRATCHPAD APPLIES ONLY
IF THE MEMORY
AREA IS NOT
PROTECTED.
IF WRITE PROTECTED,
THE DS2431 COPIES
THE DATE BYTE FROM
THE TARGET ADDRESS
INTO THE SCRATCHPAD.
IF IN EPROM MODE,
THE DS2431 LOADS
THE BITWISE LOGICAL
AND OF THE TRANSMITTED
BYTE AND THE DATA
BYTE FROM THE TARGETED
ADDRESS INTO THE
SCRATCHPAD.
BUS MASTER
Rx "1"s
DS2431
INCREMENTS
E[2:0]
PF = 0
DS2431
SETS PF = 1
CLEARS AA = 0
SETS E[2:0] = T[2:0]
0Fh
WRITE SCRATCHPAD? N
Y
N
Y
N
Y
Y
Y
N
N
MASTER Tx RESET?
E[2:0] = 7?
T[2:0] = 0?
MASTER Tx RESET?
DS2431 SETS
SCRATCHPAD
BYTE COUNTER = T[2:0]
AAh
READ SCRATCHPAD? N
Y
DS2431 Tx CRC-16 OF
COMMAND, ADDRESS,
AND DATA BYTES AS THEY
WERE SENT BY THE BUS
MASTER
BUS MASTER
Rx "1"s
Y
NMASTER Tx RESET?
BUS MASTER Rx CRC-16
OF COMMAND, ADDRESS,
E/S BYTE, AND DATA BYTES
AS SENT BY THE DS2431
Y
N
MASTER Tx RESET?
Y
BYTE COUNTER
= E[2:0]?
FROM ROM FUNCTIONS
FLOWCHART (FIGURE 9)
TO ROM FUNCTIONS
FLOWCHART (FIGURE 9)
DS2431
INCREMENTS
BYTE COUNTER
N
TO FIGURE 7b
FROM FIGURE 7b
Figure 7a. Memory Function Flowchart
DS2431
1024-Bit, 1-Wire EEPROM
______________________________________________________________________________________ 11
BUS MASTER Tx
TA1 (T[7:0]), TA2 (T[15:8])
APPLICABLE TO ALL R/W
MEMORY LOCATIONS.
DURATION: tPROG *
* 1-Wire IDLE HIGH FOR POWER.
DS2431 COPIES
SCRATCHPAD
DATA TO ADDRESS
BUS MASTER
Rx "1"s
AA = 1
BUS MASTER
Rx "1"s
MASTER Tx RESET? NY
N
N
MASTER Tx RESET?
Y
MASTER Tx RESET?
BUS MASTER Tx
TA1 (T[7:0]), TA2 (T[15:8])
AND E/S BYTE
55h
COPY SCRATCHPAD? N
Y
Y
Y
N
DS2431 Tx "0"
DS2431 Tx "1"
F0h
READ MEMORY? N
Y
Y
N
AUTH. CODE
MATCH?
Y
N
Y
N
N
T[15:0] < 0090h?
PF = 0?
ADDRESS < 90h?
YCOPY PROTECTED?
BUS MASTER
Rx "1"s
MASTER Tx RESET?
N
Y
DS2431 SETS MEMORY
ADDRESS = (T[15:0])
BUS MASTER Rx
DATA BYTE FROM
MEMORY ADDRESS
Y
N
N
MASTER Tx RESET?
ADDRESS < 8Fh?
N
Y
MASTER Tx RESET?
DS2431
INCREMENTS
ADDRESS
COUNTER
Y
TO FIGURE 7a
FROM FIGURE 7a
Figure 7b. Memory Function Flowchart (continued)
DS2431
1024-Bit, 1-Wire EEPROM
12 ______________________________________________________________________________________
Read Scratchpad [AAh]
The Read Scratchpad command allows verifying the
target address and the integrity of the scratchpad data.
After issuing the command code, the master begins
reading. The first two bytes are the target address. The
next byte is the ending offset/data status byte (E/S) fol-
lowed by the scratchpad data, which may be different
from what the master originally sent. This is of particular
importance if the target address is within the register
page or a page in either write-protection mode or
EPROM mode. See the
Write Scratchpad [0Fh]
section
for details. The master should read through the scratch-
pad (E[2:0] - T[2:0] + 1 bytes), after which it receives
the inverted CRC based on data as it was sent by the
DS2431. If the master continues reading after the CRC,
all data is logic 1.
Copy Scratchpad [55h]
The Copy Scratchpad command is used to copy data
from the scratchpad to writable memory sections. After
issuing the Copy Scratchpad command, the master
must provide a 3-byte authorization pattern, which
should have been obtained by an immediately preced-
ing Read Scratchpad command. This 3-byte pattern
must exactly match the data contained in the three
address registers (TA1, TA2, E/S, in that order). If the
pattern matches, the target address is valid, the PF flag
is not set, and the target memory is not copy protected,
then the AA flag is set and the copy begins. All 8 bytes
of scratchpad contents are copied to the target memo-
ry location. The duration of the device’s internal data
transfer is tPROG during which the voltage on the 1-Wire
bus must not fall below 2.8V. A pattern of alternating 0s
and 1s are transmitted after the data has been copied
until the master issues a reset pulse. If the PF flag is set
or the target memory is copy protected, the copy does
not begin and the AA flag is not set.
Read Memory [F0h]
The Read Memory command is the general function to
read data from the DS2431. After issuing the com-
mand, the master must provide the 2-byte target
address. After these 2 bytes, the master reads data
beginning from the target address and can continue
until address 008Fh. If the master continues reading,
the result is logic 1s. The device’s internal TA1, TA2,
E/S, and scratchpad contents are not affected by a
Read Memory command.
1-Wire Bus System
The 1-Wire bus is a system that has a single bus mas-
ter and one or more slaves. In all instances the DS2431
is a slave device. The bus master is typically a micro-
controller. The discussion of this bus system is broken
down into three topics: hardware configuration, trans-
action sequence, and 1-Wire signaling (signal types
and timing). The 1-Wire protocol defines bus transac-
tions in terms of the bus state during specific time slots,
which are initiated on the falling edge of sync pulses
from the bus master.
Hardware Configuration
The 1-Wire bus has only a single line by definition; it is
important that each device on the bus be able to drive
it at the appropriate time. To facilitate this, each device
attached to the 1-Wire bus must have open-drain or
three-state outputs. The 1-Wire port of the DS2431 is
open drain with an internal circuit equivalent to that
shown in Figure 8.
A multidrop bus consists of a 1-Wire bus with multiple
slaves attached. The DS2431 supports both a standard
and overdrive communication speed of 15.4kbps (max)
and 125kbps (max), respectively. Note that legacy
1-Wire products support a standard communication
speed of 16.3kbps and overdrive of 142kbps. The
slightly reduced rates for the DS2431 are a result of
additional recovery times, which in turn were driven by
a 1-Wire physical interface enhancement to improve
noise immunity. The value of the pullup resistor primari-
ly depends on the network size and load conditions.
The DS2431 requires a pullup resistor of 2.2kΩ(max) at
any speed.
The idle state for the 1-Wire bus is high. If for any rea-
son a transaction needs to be suspended, the bus
must be left in the idle state if the transaction is to
resume. If this does not occur and the bus is left low for
more than 16µs (overdrive speed) or more than 120µs
(standard speed), one or more devices on the bus
could be reset.
Transaction Sequence
The protocol for accessing the DS2431 through the
1-Wire port is as follows:
Initialization
ROM Function Command
Memory Function Command
Transaction/Data
DS2431
1024-Bit, 1-Wire EEPROM
______________________________________________________________________________________ 13
Initialization
All transactions on the 1-Wire bus begin with an initial-
ization sequence. The initialization sequence consists
of a reset pulse transmitted by the bus master followed
by presence pulse(s) transmitted by the slave(s). The
presence pulse lets the bus master know that the
DS2431 is on the bus and is ready to operate. For more
details, see the
1-Wire Signaling
section.
1-Wire ROM Function
Commands
Once the bus master has detected a presence, it can
issue one of the seven ROM function commands that
the DS2431 supports. All ROM function commands are
8 bits long. A list of these commands follows (see the
flowchart in Figure 9).
Read ROM [33h]
The Read ROM command allows the bus master to read
the DS2431’s 8-bit family code, unique 48-bit serial num-
ber, and 8-bit CRC. This command can only be used if
there is a single slave on the bus. If more than one slave
is present on the bus, a data collision occurs when all
slaves try to transmit at the same time (open drain pro-
duces a wired-AND result). The resultant family code and
48-bit serial number result in a mismatch of the CRC.
Match ROM [55h]
The Match ROM command, followed by a 64-bit ROM
sequence, allows the bus master to address a specific
DS2431 on a multidrop bus. Only the DS2431 that exact-
ly matches the 64-bit ROM sequence responds to the
subsequent memory function command. All other slaves
wait for a reset pulse. This command can be used with a
single device or multiple devices on the bus.
Search ROM [F0h]
When a system is initially brought up, the bus master
might not know the number of devices on the 1-Wire
bus or their registration numbers. By taking advantage
of the wired-AND property of the bus, the master can
use a process of elimination to identify the registration
numbers of all slave devices. For each bit of the regis-
tration number, starting with the least significant bit, the
bus master issues a triplet of time slots. On the first slot,
each slave device participating in the search outputs
the true value of its registration number bit. On the sec-
ond slot, each slave device participating in the search
outputs the complemented value of its registration num-
ber bit. On the third slot, the master writes the true
value of the bit to be selected. All slave devices that do
not match the bit written by the master stop participat-
ing in the search. If both of the read bits are zero, the
master knows that slave devices exist with both states
of the bit. By choosing which state to write, the bus
master branches in the ROM code tree. After one com-
plete pass, the bus master knows the registration num-
ber of a single device. Additional passes identify the
registration numbers of the remaining devices. Refer to
Application Note 187:
1-Wire Search Algorithm
for a
detailed discussion, including an example.
Skip ROM [CCh]
This command can save time in a single-drop bus sys-
tem by allowing the bus master to access the memory
functions without providing the 64-bit ROM code. If
more than one slave is present on the bus and, for
example, a read command is issued following the Skip
ROM command, data collision occurs on the bus as
multiple slaves transmit simultaneously (open-drain
pulldowns produce a wired-AND result).
Rx
RPUP
IL
VPUP
BUS MASTER
OPEN-DRAIN
PORT PIN 100Ω MOSFET
Tx
Rx
Tx
DATA
DS2431 1-Wire PORT
Rx = RECEIVE
Tx = TRANSMIT
Figure 8. Hardware Configuration
DS2431
1024-Bit, 1-Wire EEPROM
14 ______________________________________________________________________________________
DS2431 Tx
PRESENCE PULSE
BUS MASTER Tx
RESET PULSE
BUS MASTER Tx ROM
FUNCTION COMMAND
DS2431 Tx
CRC BYTE
DS2431 Tx
FAMILY CODE
(1 BYTE)
DS2431 Tx
SERIAL NUMBER
(6 BYTES)
RC = 0
MASTER Tx BIT 0
RC = 0 RC = 0 RC = 0
OD = 0
YY
Y
Y
Y
Y
Y
Y
33h
READ ROM
COMMAND?
N55h
MATCH ROM
COMMAND?
BIT 0 MATCH? BIT 0 MATCH?
N
N N
N N
N N
F0h
SEARCH ROM
COMMAND?
OD
RESET PULSE?
N
N
CCh
SKIP ROM
COMMAND?
N
RC = 1
MASTER Tx BIT 1
MASTER Tx BIT 63
BIT 1 MATCH?
BIT 63 MATCH?
Y
Y
RC = 1
FROM MEMORY FUNCTIONS
FLOWCHART (FIGURE 7)
TO MEMORY FUNCTIONS
FLOWCHART (FIGURE 7)
DS2431 Tx BIT 0
DS2431 Tx BIT 0
MASTER Tx BIT 0
BIT 1 MATCH?
BIT 63 MATCH?
DS2431 Tx BIT 1
DS2431 Tx BIT 1
MASTER Tx BIT 1
DS2431 Tx BIT 63
DS2431 Tx BIT 63
MASTER Tx BIT 63
Y
TO FIGURE 9b
TO FIGURE 9b
FROM FIGURE 9b
FROM FIGURE 9b
Figure 9a. ROM Functions Flowchart
DS2431
1024-Bit, 1-Wire EEPROM
______________________________________________________________________________________ 15
RC = 0; OD = 1 RC = 0; OD = 1
N
BIT 0 MATCH?
YN
RC = 1?
Y
A5h
RESUME
COMMAND?
N
Y
3Ch
OVERDRIVE-
SKIP ROM?
N
Y
69h
OVERDRIVE-
MATCH ROM?
FROM FIGURE 9a
FROM FIGURE 9a
TO FIGURE 9a
TO FIGURE 9a
N
Y
Y
N
MASTER Tx
RESET?
Y
MASTER Tx
RESET?
NBIT 1 MATCH?
MASTER Tx BIT 0
MASTER Tx BIT 1
OD = 0
NOD = 0
NOD = 0
Y
RC = 1
BIT 63 MATCH?
MASTER Tx BIT 63
Y
Figure 9b. ROM Functions Flowchart (continued)
DS2431
1024-Bit, 1-Wire EEPROM
16 ______________________________________________________________________________________
Resume [A5h]
To maximize the data throughput in a multidrop envi-
ronment, the Resume command is available. This com-
mand checks the status of the RC bit and, if it is set,
directly transfers control to the memory function com-
mands, similar to a Skip ROM command. The only way
to set the RC bit is through successfully executing the
Match ROM, Search ROM, or Overdrive-Match ROM
command. Once the RC bit is set, the device can
repeatedly be accessed through the Resume com-
mand. Accessing another device on the bus clears the
RC bit, preventing two or more devices from simultane-
ously responding to the Resume command.
Overdrive-Skip ROM [3Ch]
On a single-drop bus this command can save time by
allowing the bus master to access the memory func-
tions without providing the 64-bit ROM code. Unlike the
normal Skip ROM command, the Overdrive-Skip ROM
command sets the DS2431 into the overdrive mode
(OD = 1). All communication following this command
must occur at overdrive speed until a reset pulse of
minimum 480µs duration resets all devices on the bus
to standard speed (OD = 0).
When issued on a multidrop bus, this command sets all
overdrive-supporting devices into overdrive mode. To
subsequently address a specific overdrive-supporting
device, a reset pulse at overdrive speed must be
issued followed by a Match ROM or Search ROM com-
mand sequence. This speeds up the time for the
search process. If more than one slave supporting
overdrive is present on the bus and the Overdrive-Skip
ROM command is followed by a read command, data
collision occurs on the bus as multiple slaves transmit
simultaneously (open-drain pulldowns produce a wired-
AND result).
Overdrive-Match ROM [69h]
The Overdrive-Match ROM command followed by a 64-
bit ROM sequence transmitted at overdrive speed
allows the bus master to address a specific DS2431 on
a multidrop bus and to simultaneously set it in overdrive
mode. Only the DS2431 that exactly matches the 64-bit
ROM sequence responds to the subsequent memory
function command. Slaves already in overdrive mode
from a previous Overdrive-Skip ROM or successful
Overdrive-Match ROM command remain in overdrive
mode. All overdrive-capable slaves return to standard
speed at the next reset pulse of minimum 480µs dura-
tion. The Overdrive-Match ROM command can be used
with a single device or multiple devices on the bus.
1-Wire Signaling
The DS2431 requires strict protocols to ensure data
integrity. The protocol consists of four types of signal-
ing on one line: reset sequence with reset pulse and
presence pulse, write-zero, write-one, and read-data.
Except for the presence pulse, the bus master initiates
all falling edges. The DS2431 can communicate at two
different speeds: standard speed and overdrive speed.
If not explicitly set into the overdrive mode, the DS2431
communicates at standard speed. While in overdrive
mode, the fast timing applies to all waveforms.
To get from idle to active, the voltage on the 1-Wire line
needs to fall from VPUP below the threshold VTL. To get
from active to idle, the voltage needs to rise from
VILMAX past the threshold VTH. The time it takes for the
voltage to make this rise is seen in Figure 10 as ε, and
its duration depends on the pullup resistor (RPUP) used
and the capacitance of the 1-Wire network attached.
The voltage VILMAX is relevant for the DS2431 when
determining a logical level, not triggering any events.
Figure 10 shows the initialization sequence required to
begin any communication with the DS2431. A reset
pulse followed by a presence pulse indicates that the
DS2431 is ready to receive data, given the correct ROM
and memory function command. If the bus master uses
slew-rate control on the falling edge, it must pull down
the line for tRSTL + tFto compensate for the edge. A
tRSTL duration of 480µs or longer exits the overdrive
mode, returning the device to standard speed. If the
DS2431 is in overdrive mode and tRSTL is no longer
than 80µs, the device remains in overdrive mode. If the
device is in overdrive mode and tRSTL is
between
80µs
and 480µs, the device resets, but the communication
speed is undetermined.
After the bus master has released the line it goes into
receive mode. Now the 1-Wire bus is pulled to VPUP
through the pullup resistor or, in the case of a DS2482-
x00 or DS2480B driver, through the active circuitry.
When the threshold VTH is crossed, the DS2431 waits
for tPDH and then transmits a presence pulse by pulling
the line low for tPDL. To detect a presence pulse, the
master must test the logical state of the 1-Wire line at
tMSP.
The tRSTH window must be at least the sum of
tPDHMAX, tPDLMAX, and tRECMIN. Immediately after
tRSTH is expired, the DS2431 is ready for data commu-
nication. In a mixed population network, tRSTH should
be extended to minimum 480µs at standard speed and
48µs at overdrive speed to accommodate other 1-Wire
devices.
DS2431
1024-Bit, 1-Wire EEPROM
______________________________________________________________________________________ 17
Read/Write Time Slots
Data communication with the DS2431 takes place in
time slots that carry a single bit each. Write time slots
transport data from bus master to slave. Read time
slots transfer data from slave to master. Figure 11 illus-
trates the definitions of the write and read time slots.
All communication begins with the master pulling the
data line low. As the voltage on the 1-Wire line falls
below the threshold VTL, the DS2431 starts its internal
timing generator that determines when the data line is
sampled during a write time slot and how long data is
valid during a read time slot.
Master-to-Slave
For a write-one time slot, the voltage on the data line
must have crossed the VTH threshold before the write-
one low time tW1LMAX is expired. For a write-zero time
slot, the voltage on the data line must stay below the
VTH threshold until the write-zero low time tW0LMIN is
expired. For the most reliable communication, the volt-
age on the data line should not exceed VILMAX during
the entire tW0L or tW1L window. After the VTH threshold
has been crossed, the DS2431 needs a recovery time
tREC before it is ready for the next time slot.
Slave-to-Master
A read-data time slot begins like a write-one time slot.
The voltage on the data line must remain below VTL
until the read low time tRL is expired. During the tRL
window, when responding with a 0, the DS2431 starts
pulling the data line low; its internal timing generator
determines when this pulldown ends and the voltage
starts rising again. When responding with a 1, the
DS2431 does not hold the data line low at all, and the
voltage starts rising as soon as tRL is over.
The sum of tRL + δ(rise time) on one side and the inter-
nal timing generator of the DS2431 on the other side
define the master sampling window (tMSRMIN to
tMSRMAX), in which the master must perform a read
from the data line. For the most reliable communication,
tRL should be as short as permissible, and the master
should read close to but no later than tMSRMAX. After
reading from the data line, the master must wait until
tSLOT is expired. This guarantees sufficient recovery
time tREC for the DS2431 to get ready for the next time
slot. Note that tREC specified herein applies only to a
single DS2431 attached to a 1-Wire line. For multide-
vice configurations, tREC must be extended to accom-
modate the additional 1-Wire device input capacitance.
Alternatively, an interface that performs active pullup
during the 1-Wire recovery time such as the DS2482-
x00 or DS2480B 1-Wire line drivers can be used.
RESISTOR MASTER DS2431
tRSTL tPDL
tRSTH
tPDH
MASTER Tx "RESET PULSE" MASTER Rx "PRESENCE PULSE"
VPUP
VIHMASTER
VTH
VTL
VILMAX
0V
ε
tF
tREC
tMSP
Figure 10. Initialization Procedure: Reset and Presence Pulse
DS2431
1024-Bit, 1-Wire EEPROM
18 ______________________________________________________________________________________
RESISTOR MASTER
RESISTOR MASTER
RESISTOR MASTER DS2431
ε
ε
δ
VPUP
VIHMASTER
VTH
VTL
VILMAX
0V
tF
VPUP
VIHMASTER
VTH
VTL
VILMAX
0V
tF
VPUP
VIHMASTER
VTH
VTL
VILMAX
0V
tF
tSLOT
tW1L
tREC
tSLOT
tSLOT
tW0L
tREC
MASTER
SAMPLING
WINDOW
tRL
tMSR
WRITE-ONE TIME SLOT
WRITE-ZERO TIME SLOT
READ-DATA TIME SLOT
Figure 11. Read/Write Timing Diagrams
DS2431
1024-Bit, 1-Wire EEPROM
______________________________________________________________________________________ 19
Improved Network Behavior
(Switchpoint Hysteresis)
In a 1-Wire environment, line termination is possible
only during transients controlled by the bus master
(1-Wire driver). 1-Wire networks, therefore, are suscep-
tible to noise of various origins. Depending on the
physical size and topology of the network, reflections
from end points and branch points can add up or can-
cel each other to some extent. Such reflections are visi-
ble as glitches or ringing on the 1-Wire communication
line. Noise coupled onto the 1-Wire line from external
sources can also result in signal glitching. A glitch dur-
ing the rising edge of a time slot can cause a slave
device to lose synchronization with the master and,
consequently, result in a Search ROM command com-
ing to a dead end or cause a device-specific function
command to abort. For better performance in network
applications, the DS2431 uses a new 1-Wire front-end,
which makes it less sensitive to noise.
The DS2431’s 1-Wire front-end differs from traditional
slave devices in three characteristics.
1) There is additional lowpass filtering in the circuit that
detects the falling edge at the beginning of a time
slot. This reduces the sensitivity to high-frequency
noise. This additional filtering does not apply at
overdrive speed.
2) There is a hysteresis at the low-to-high switching
threshold VTH. If a negative glitch crosses VTH but
does not go below VTH - VHY, it is not recognized
(Figure 12, Case A). The hysteresis is effective at
any 1-Wire speed.
3) There is a time window specified by the rising edge
hold-off time tREH during which glitches are ignored,
even if they extend below the VTH - VHY threshold
(Figure 12, Case B, tGL < tREH). Deep voltage drops
or glitches that appear late after crossing the VTH
threshold and extend beyond the tREH window can-
not be filtered out and are taken as the beginning of a
new time slot (Figure 12, Case C, tGL tREH).
Devices that have the parameters VHY and tREH speci-
fied in their electrical characteristics use the improved
1-Wire front-end.
CRC Generation
The DS2431 uses two different types of CRCs. One
CRC is an 8-bit type and is stored in the most signifi-
cant byte of the 64-bit ROM. The bus master can com-
pute a CRC value from the first 56 bits of the 64-bit
ROM and compare it to the value stored within the
DS2431 to determine if the ROM data has been
received error-free. The equivalent polynomial function
of this CRC is X8+ X5+ X4+ 1. This 8-bit CRC is
received in the true (noninverted) form. It is computed
at the factory and lasered into the ROM.
The other CRC is a 16-bit type, generated according to
the standardized CRC-16 polynomial function X16 + X15
+ X2+ 1. This CRC is used for fast verification of a data
transfer when writing to or reading from the scratchpad.
In contrast to the 8-bit CRC, the 16-bit CRC is always
communicated in the inverted form. A CRC generator
inside the DS2431 chip (Figure 13) calculates a new 16-
bit CRC, as shown in the command flowchart (Figure 7).
The bus master compares the CRC value read from the
device to the one it calculates from the data and
decides whether to continue with an operation or to
reread the portion of the data with the CRC error.
With the Write Scratchpad command, the CRC is gen-
erated by first clearing the CRC generator and then
shifting in the command code, the target addresses
TA1 and TA2, and all the data bytes as they were sent
VPUP
VTH VHY
0V
tREH
tGL
tREH
tGL
CASE A CASE CCASE B
Figure 12. Noise Suppression Scheme
DS2431
1024-Bit, 1-Wire EEPROM
20 ______________________________________________________________________________________
by the bus master. The DS2431 transmits this CRC only
if E[2:0] = 111b.
With the Read Scratchpad command, the CRC is gen-
erated by first clearing the CRC generator and then
shifting in the command code, the target addresses
TA1 and TA2, the E/S byte, and the scratchpad data as
they were sent by the DS2431. The DS2431 transmits
this CRC only if the reading continues through the end
of the scratchpad. For more information on generating
CRC values, refer to Application Note 27.
1ST
STAGE
2ND
STAGE
3RD
STAGE
4TH
STAGE
7TH
STAGE
8TH
STAGE
6TH
STAGE
5TH
STAGE
X0X1X2X3X4
POLYNOMIAL = X16 + X15 + X2 + 1
INPUT DATA
CRC OUTPUT
X5X6
11TH
STAGE
12TH
STAGE
15TH
STAGE
14TH
STAGE
13TH
STAGE
X11 X12
9TH
STAGE
10TH
STAGE
X9X10 X13 X14
X7
16TH
STAGE
X16
X15
X8
Figure 13. CRC-16 Hardware Description and Polynomial
Command-Specific 1-Wire Communication Protocol—Legend
SYMBOL DESCRIPTION
RST 1-Wire reset pulse generated by master.
PD 1-Wire presence pulse generated by slave.
Select Command and data to satisfy the ROM function protocol.
WS Command "Write Scratchpad."
RS Command "Read Scratchpad."
CPS Command "Copy Scratchpad."
RM Command "Read Memory."
TA Target address TA1, TA2.
TA-E/S Target address TA1, TA2 with E/S byte.
<8T[2:0] bytes> Transfer of as many bytes as needed to reach the end of the scratchpad for a given target address.
<Data to EOM> Transfer of as many data bytes as are needed to reach the end of the memory.
CRC-16 Transfer of an inverted CRC-16.
FF Loop Indefinite loop where the master reads FF bytes.
AA Loop Indefinite loop where the master reads AA bytes.
Programming Data transfer to EEPROM; no activity on the 1-Wire bus permitted during this time.
DS2431
1024-Bit, 1-Wire EEPROM
______________________________________________________________________________________ 21
Command-Specific 1-Wire Communication Protocol—Color Codes
1-Wire Communication Examples
Master to Slave Slave to Master Programming
Write Scratchpad (Cannot Fail)
RST PD Select WS TA <8–T[2:0] bytes> CRC-16 FF Loop
Read Scratchpad (Cannot Fail)
RST PD Select RS TA-E/S <8–T[2:0] bytes> CRC-16 FF Loop
Copy Scratchpad (Success)
RST PD Select CPS TA-E/S Programming AA Loop
Copy Scratchpad (Invalid Address or PF = 1 or Copy Protected)
RST PD Select CPS TA-E/S FF Loop
Read Memory (Success)
RST PD Select RM TA <Data to EOM> FF Loop
Read Memory (Invalid Address)
RST PD Select RM TA FF Loop
DS2431
1024-Bit, 1-Wire EEPROM
22 ______________________________________________________________________________________
Memory Function Example
Write to the first 8 bytes of memory page 1. Read the
entire memory.
With only a single DS2431 connected to the bus mas-
ter, the communication looks like this:
MASTER MODE DATA (LSB FIRST) COMMENTS
Tx (Reset) Reset pulse
Rx (Presence) Presence pulse
Tx CCh Issue “Skip ROM” command
Tx 0Fh Issue “Write Scratchpad” command
Tx 20h TA1, beginning offset = 20h
Tx 00h TA2, address = 0020h
Tx <8 Data Bytes> Write 8 bytes of data to scratchpad
Rx <2 Bytes CRC-16> Read CRC to check for data integrity
Tx (Reset) Reset pulse
Rx (Presence) Presence pulse
Tx CCh Issue “Skip ROM” command
Tx AAh Issue Read Scratchpad” command
Rx 20h Read TA1, beginning offset = 20h
Rx 00h Read TA2, address = 0020h
Rx 07h Read E/S, ending offset = 111b, AA, PF = 0
Rx <8 Data Bytes> Read scratchpad data and verify
Rx <2 Bytes CRC-16> Read CRC to check for data integrity
Tx (Reset) Reset pulse
Rx (Presence) Presence pulse
Tx CCh Issue “Skip ROM” command
Tx 55h Issue Copy Scratchpad” command
Tx 20h TA1
Tx 00h TA2
Tx 07h E/S
(AUTHORIZATION CODE)
<1-Wire Idle High> Wait tPROGMAX for the copy function to complete
Rx AAh Read copy status, AAh = success
Tx (Reset) Reset pulse
Rx (Presence) Presence pulse
Tx CCh Issue “Skip ROM” command
Tx F0h IssueRead Memory” command
Tx 00h TA1, beginning offset = 00h
Tx 00h TA2, address = 0000h
Rx <144 Data Bytes> Read the entire memory
Tx (Reset) Reset pulse
Rx (Presence) Presence pulse
DS2431
1024-Bit, 1-Wire EEPROM
______________________________________________________________________________________ 23
2
3
1
2
3
1
3
2
1
N.C.
IO
GND
TO-92
TOP VIEW
N.C.
IO
GND
N.C.
N.C.
N.C.
TSOC
+
5
4
6
2
3
1
DS2431
SFN
(6mm
×
6mm
×
0.9mm)
BOTTOM VIEW
NOTE: THE SFN PACKAGE IS QUALIFIED FOR ELECTRO-MECHANICAL
CONTACT APPLICATIONS ONLY, NOT FOR SOLDERING. FOR MORE
INFORMATION, REFER TO APPLICATION NOTE 4132: ATTACHMENT
METHODS FOR THE ELECTRO-MECHANICAL SFN PACKAGE.
12
IO GND
SIDE VIEW
FRONT VIEW (T&R VERSION)
FRONT VIEWSIDE VIEW
DS2431
UCSPR
TOP VIEW
GND N.C. N.C.
A1 A2 A3
C1 C2 C3
IO N.C. N.C.
16N.C. N.C.
25IO N.C.
34GND N.C.
TDFN-EP
(3mm
×
3mm)
TOP VIEW
DS2431
2431
ymrrF
+
*EP
*EXPOSED PAD
Pin Configurations
DS2431
1024-Bit, 1-Wire EEPROM
24 ______________________________________________________________________________________
USER DIRECTION OF FEED
LEADS FACE UP IN ORIENTATION SHOWN ABOVE.
SFN Package Orientation on Tape and Reel
PACKAGE TYPE PACKAGE CODE DOCUMENT NO.
3 TO-92 (Bulk) Q3+1 21-0248
3 TO-92 (T&R) Q3+4 21-0250
6 TSOC D6+1 21-0382
2 SFN G266+1 21-0390
6 TDFN-EP T633+2 21-0137
6 UCSPR BR622+1 21-0376
Package Information
For the latest package outline information and land patterns, go to www.maxim-ic.com/packages.
DS2431
1024-Bit, 1-Wire EEPROM
______________________________________________________________________________________ 25
Revision History
REVISION
NUMBER
REVISION
DATE DESCRIPTION PAGES
CHANGED
0 050704 Initial release. ——
Replaced Pin Configuration. 1
In the Electrical Characteristics table, changed VTL(MIN) from 0.5V to 0.46V and
VTL(MAX) from 4.1V to 4.4V; changed VHY(MIN) from 0.22V to 0.21V 2
1 081604
In the Copy Scratchpad [55h] section, corrected the copy time from 13ms to 12.5ms. 14
Added the SFN package and updated the Ordering Information table. 1, 24
In the Pin Configuration, added a note to the CSP package outline “*See package
reliability report for important guidelines on qualified usage conditions. 1
In the Electrical Characteristics table, changed the tPROG (programming time) EC
table parameter from 12.5ms to 10ms for version A2 (see also pages 1, 13).
Removed tFPD and updated tPDH, tMSP, tW0L accordingly. Changed IPROG max to
0.8mA to match GBD.
1, 2, 3, 13
2 090506
Updated Memory Function Example table. 23
Added CSP package outline drawing number to Pin Configuration. 1
Changed VTL(MIN) from 0.46V to 0.5V in the Electrical Characteristics table. 2
3 122106
In the Absolute Maximum Ratings, changed storage temp to -5C to +125°C; in the
Electrical Characteristics table, changed VTH, VTL based on VPUP and data retention
to 40 years min at 85°C; added note to retention spec: “EEPROM writes can become
nonfunctional after the data-retention time is exceeded. Long-term storage at
elevated temperatures is not recommended; the device can lose its write capability
after 10 years at +125°C or 40 years at +85°C.
1, 2, 3
In the Ordering Information table, removed all leaded part numbers and added the
TDFN-EP package. 1, 24
In the Electrical Characteristics table, changed the VIL(MAX) spec from 0.3V to 0.5V;
removed from the tW1L(MAX) spec; added Note 17 to tW0L spec; updated EC table
Notes 17 and 18; corrected Note 20.
2, 3
Added EP function to the Pin Description table. 3
Added to Figure 11 Write-Zero Time Slot. 19
4 102207
In the Pin Configuration, added the package drawing information/weblink and a note
that the SFN package is qualified for electro-mechanical contact applications only,
not for soldering. Added the SFN Package Orientation on Tape-and-Reel section. In
the Ordering Information, added note to contact factory for availability of the UCSPR
package. Added note that TO-92 T&R leads are formed to approximately 100-mil
spacing.
24
In the SFN Pin Configuration, added reference to Application Note 4132. 24
5 032008
Added Package Information table. 25
6 8/08 Created newer template-style data sheet. All
DS2431
1024-Bit, 1-Wire EEPROM
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
26
____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2009 Maxim Integrated Products Maxim is a registered trademark of Maxim Integrated Products, Inc.
Revision History (continued)
REVISION
NUMBER
REVISION
DATE DESCRIPTION PAGES
CHANGED
7 6/09
Deleted “contact factory” note in Ordering Information.
Updated Pin Description and Pin Configurations to reflect changes in pin
assignment of UCSPR package.
1, 5, 23
8 10/09 Corrected part number in Ordering Information table. 1