IP140A IP140 IP7800A IP7800 LM140 1 1 SERIES SERIES SERIES SERIES SERIES 1 AMP POSITIVE VOLTAGE REGULATOR 2 2 3 3 Pin 1 - VIN Pin 2 - VOUT Case - Ground Pin 1 - VIN Pin 2 - VOUT Case - Ground K Package - TO-3 FEATURES R Package - TO-66 1 * OUTPUT CURRENT UP TO 1.0A * OUTPUT VOLTAGES OF 5, 12, 15V 3 * 0.01% / V LINE REGULATION 1 2 3 * 0.3% / A LOAD REGULATION 2 * THERMAL OVERLOAD PROTECTION Pin 1 - VIN Pin 2 - Ground Pin 3 - VOUT Case - Ground* G Package - TO-257 IG Package- TO-257* * SHORT CIRCUIT PROTECTION Pin 1 - VIN Pin 2 - Ground Pin 3 - VOUT * OUTPUT TRANSISTOR SOA PROTECTION * 1% VOLTAGE TOLERANCE (-A VERSIONS) SMD 1 PACKAGE Ceramic Surface Mount * isolated Case on IG package 7.54 (0.296) 0.76 (0.030) min. 12 13 14 15 16 2.41 (0.095) 3.175 (0.125) Max. 2.41 (0.095) 2 2 0.127 (0.005) 0.127 (0.005) 16 PLCS 0.50(0.020) 7 6 5 4 3 Pins 4,5 - VIN . Pins 6,7,8,9,10,11,12,13 - VOUT Pins 15,16,17,18,1,2 - Ground 0.50 (0.020) max. 7.26 (0.286) LCC4 CERAMIC SURFACE MOUNT DESCRIPTION 3 5.72 (.225) 11 10 9 8 1 0.76 (0.030) min. 17 18 1 10.16 (0.400) 3.05 (0.120) 0.127 (0.005) Pin 1 - VIN Pin 2 - Ground Pin 3 - VOUT The IP140A / LM140 / IP7800A / IP7800 series of 3 terminal regulators is available with several fixed output voltage making them useful in a wide range of applications. The A suffix devices are fully specified at 1A, provide 0.01% / V line regulation, 0.3% / A load regulation and 1% output voltage tolerance at room temperature. Protection features include Safe Operating Area current limiting and thermal shutdown. SMD 05 PACKAGE Ceramic Surface Mount ABSOLUTE MAXIMUM RATINGS (Tcase = 25C unless otherwise stated) VI DC Input Voltage PD Power Dissipation Tj Operating Junction Temperature Range -55 to 150C Tstg Storage Temperature -65 to 150C (for VO = 5, 12, 15V) 35V Internally limited 1 Note 1. Although power dissipation is internally limited, these specifications are applicable for maximum power dissipation PMAX of 20W. IMAX = 1.0A. Semelab Plc reserves the right to change test conditions, parameter limits and package dimensions without notice. Information furnished by Semelab is believed to be both accurate and reliable at the time of going to press. However Semelab assumes no responsibility for any errors or omissions discovered in its use. Semelab encourages customers to verify that datasheets are current before placing orders. Semelab plc. Telephone +44(0)1455 556565. Fax +44(0)1455 552612. E-mail: sales@semelab.co.uk Website: http://www.semelab.co.uk Document Number 2833 Issue 2 IP140A IP140 IP7800A IP7800 LM140 Parameter VO Test Conditions Output Voltage Low Supply VO IP7805A LM,IP140A-05 Min. Typ. Max. IO = 1A VIN = 10V IO = 5mA to IMAX PD PMAX VIN = 7.5V to 20V TJ = -55 to 150C IO = 5mA to IMAX PD PMAX VIN = 7V to 20V VO Line Regulation 4.8 4.85 5.15 4.75 5.25 4.75 5.15 4.75 5.25 3 10 50 3 10 50 1 4 20 TJ = -55 to 150C 2 12 25 IO = 5mA to 1.5A 10 25 50 4 15 25 7 25 50 4 6 6 4 6.5 7 0.2 0.5 0.5 0.1 0.8 0.8 0.1 0.8 0.8 0.2 1 1.0 40 200 VIN = 7.3V to 20V Load Regulation IO = 250mA to 750mA VIN = 10V IQ Quiescent Current IQ Quiescent Current Change IO = 5mA to IMAX TJ = -55 to 150C IO IMAX VIN = 10V TJ = -55 to 150C IO = 5mA to IMAX VIN = 10V IO IMAX VIN = 7.5V to 20V TJ = -55 to 150C IO 0.5 IMAX VIN = 8V to 25V IO 0.5 IMAX VIN = 7V to 25V TJ = -55 to 150C VN VIN VO Output Noise f = 10Hz to 100kHz Voltage VIN = 10V Ripple Rejection f = 120Hz VIN = 8V to 18V IO IMAX IO 0.5 IMAX TJ = -55 to 150C 80 68 68 80 68 Dropout Voltage IO = IMAX 2 Output Resistance f = 1 kHz 5 Isc Short Circuit Current VIN = 35V 0.6 1.2 0.6 1.2 Ipk Peak Output Current VIN = 10V 2.4 3.3 2.4 3.3 0.2 2 0.6 Average Temperature Coefficient of VO Input Voltage required to maintain line regulation IO = 5mA IO IMAX 7.3 7.3 V mV mV mA mA dB RO 2.5 V V 40 68 Units 5.2 50 VIN = 8V to 12V VO 5 10 TJ = -55 to 150C VIN = 10V 5 3 VIN = 7.5V to 25V IO IMAX IP7805 LM,IP140-05 Min. Typ. Max. 5.05 4.95 VIN = 7V to 25V IO = 0.5 IMAX SERIES SERIES SERIES SERIES SERIES 2 V 5 m A mV C V 1) All characteristics are measured with a capacitor across the input of 0.22F and a capacitor across the output of 0.1F. All characteristics except noise voltage and ripple rejection ratio are measured using pulse techniques (tp 10ms, 5%). Output voltage changes due to changes in internal temperature must be taken into account separately. 2) Although power dissipation is internally limited, these specifications are applicable for maximum power dissipation PMAX of 20W , IMAX = 1.0A. 3) TJ = 25C unless otherwise stated. Semelab plc. Telephone +44(0)1455 556565. Fax +44(0)1455 552612. E-mail: sales@semelab.co.uk Website: http://www.semelab.co.uk Document Number 2833 Issue 2 IP140A IP140 IP7800A IP7800 LM140 Parameter VO Test Conditions Output Voltage IO = 1A VIN = 19V IO = 5mA to IMAX PD PMAX VIN = 14.8V to 27V TJ = -55 to 150C Low Supply VO PD PMAX IO = 5mA to IMAX VIN = 14.5V to 27V IP7812A LM,IP140A-12 Min. Typ. Max. IP7812 LM,IP140-12 Min. Typ. Max. 11.88 12.12 11.5 11.64 12.36 11.4 12.6 11.40 12.36 11.4 12.6 4 18 120 4 18 120 2 9 50 TJ = -55 to 150C 4 30 60 IO = 5mA to 1.5A 12 32 120 IO = 250mA to 750mA 4 19 60 8 60 120 4 6 6 4 6.5 7 0.2 0.5 0.5 0.1 0.8 0.8 0.1 0.8 0.8 0.2 1 1 75 480 VIN = 14.8V to 30V IO IMAX VIN = 14.5V to 27V VIN = 16V to 22V VO Load Regulation VIN = 19V IO = 5mA to IMAX TJ = -55 to 150C IQ Quiescent Current IQ IO IMAX VIN = 19V TJ = -55 to 150C IO = 5mA to IMAX VIN = 19V IO IMAX VIN = 14.8V to 27V Quiescent Current Change TJ = -55 to 150C IO 0.5 IMAX VIN = 15V to 30V IO 0.5 IMAX VIN = 14.5V to 30V TJ = -55 to 150C VN VIN VO Output Noise f = 10Hz to 100kHz Voltage VIN = 19V Ripple Rejection f = 120Hz VIN = 15V to 25V IO IMAX IO 0.5 IMAX TJ = -55 to 150C 72 61 61 72 61 Dropout Voltage IO = IMAX 2 Output Resistance f = 1 kHz 8 Isc Short Circuit Current VIN = 35V 0.6 1.2 0.6 1.2 Ipk Peak Output Current VIN = 19V 2.4 3.3 2.4 3.3 0.5 4.8 1.5 Average Temperature Coefficient of VO Input Voltage required to maintain line regulation IO = 5mA IO IMAX 14.5 14.6 V mV mV mA mA dB RO 2.5 V V 75 61 Units 12.5 120 TJ = -55 to 150C VIN = 19V 12 18 IO = 0.5 IMAX Line Regulation 12 4 VIN = 14.5V to 30V VO SERIES SERIES SERIES SERIES SERIES 2 V 8 m A mV C V 1) All characteristics are measured with a capacitor across the input of 0.22F and a capacitor across the output of 0.1F. All characteristics except noise voltage and ripple rejection ratio are measured using pulse techniques (tp 10ms, 5%). Output voltage changes due to changes in internal temperature must be taken into account separately. 2) Although power dissipation is internally limited, these specifications are applicable for maximum power dissipation PMAX of 20W , IMAX = 1.0A. 3) TJ = 25C unless otherwise stated. Semelab plc. Telephone +44(0)1455 556565. Fax +44(0)1455 552612. E-mail: sales@semelab.co.uk Website: http://www.semelab.co.uk Document Number 2833 Issue 2 IP140A IP140 IP7800A IP7800 LM140 Parameter VO Test Conditions Output Voltage IO = 1A VIN = 23V IO = 5mA to IMAX PD PMAX VIN = 17.9V to 30V TJ = -55 to 150C Low Supply VO PD PMAX IO = 5mA to IMAX VIN = 17.5V to 30V IP7815A LM,IP140A-15 Min. Typ. Max. IP7815 LM,IP140-15 Min. Typ. Max. 14.85 15.15 14.4 14.55 15.45 14.25 15.75 14.25 15.45 14.25 15.75 4 22 150 4 22 150 2 10 60 TJ = -55 to 150C 5 30 75 IO = 5mA to 1.5A 12 35 150 IO = 250mA to 750mA 4 21 75 9 75 150 4 6 6 4 6.5 7 0.2 0.5 0.5 0.1 0.8 0.8 0.1 0.8 0.8 0.2 1 1 90 600 VIN = 17.9V to 30V IO IMAX VIN = 17.5V to 30V VIN = 20V to 26V VO Load Regulation VIN = 23V IO = 5mA to IMAX TJ = -55 to 150C IQ Quiescent Current IQ IO IMAX VIN = 23V TJ = -55 to 150C IO = 5mA to IMAX VIN = 23V IO IMAX VIN = 17.9V to 30V Quiescent Current Change TJ = -55 to 150C IO 0.5 IMAX VIN = 18.5V to 30V IO 0.5 IMAX VIN = 17.5V to 30V TJ = -55 to 150C VN VIN VO Output Noise f = 10Hz to 100kHz Voltage VIN = 23V Ripple Rejection f = 120Hz IO IMAX VIN = 18.5V to IO 0.5 IMAX 28.5V TJ = -55 to 150C 70 60 60 70 60 Dropout Voltage IO = IMAX 2 Output Resistance f = 1 kHz 9 Isc Short Circuit Current VIN = 35V 0.6 1.2 0.6 1.2 Ipk Peak Output Current VIN = 23V 2.4 3.3 2.4 3.3 0.6 6 1.8 Average Temperature Coefficient of VO Input Voltage required to maintain line regulation IO = 5mA IO IMAX 17.5 17.7 V mV mV mA mA dB RO 2.5 V V 90 60 Units 15.60 150 TJ = -55 to 150C VIN = 23V 15 22 IO = 0.5 IMAX Line Regulation 15 4 VIN = 17.5V to 30V VO SERIES SERIES SERIES SERIES SERIES 2 V 9 m A mV C V 1) All characteristics are measured with a capacitor across the input of 0.22F and a capacitor across the output of 0.1F. All characteristics except noise voltage and ripple rejection ratio are measured using pulse techniques (tp 10ms, 5%). Output voltage changes due to changes in internal temperature must be taken into account separately. 2) Although power dissipation is internally limited, these specifications are applicable for maximum power dissipation PMAX of 20W , IMAX = 1.0A. 3) TJ = 25C unless otherwise stated. Semelab plc. Telephone +44(0)1455 556565. Fax +44(0)1455 552612. E-mail: sales@semelab.co.uk Website: http://www.semelab.co.uk Document Number 2833 Issue 2 IP140A IP140 IP7800A IP7800 LM140 SERIES SERIES SERIES SERIES SERIES THERMAL DATA MAX Rthj-case Thermal Resistance Junction-case K-Pack 3C/W R-Pack 7C/W G/IG-Pack 5C/W LCC4 13C/W SMD 1.3C/W APPLICATIONS INFORMATION IN PU T VOU T VIN OU TPUT IN PU T GND C1 * 0 .2 2F VOU T VIN GND C2 * * OU TPUT IN PU T GND R1 C1 * 0 .2 2F C1 0 .2 2F R2 Fixed Output Regulator VOU T VIN Adjustable Output Regulator R1 O U TPU T IOUT Current Regulator * Required if the regulator is located far from the power supply. ** Although no output capacitor is needed for stability, it does help transient response.(If needed, use 0.1F ceramic disc) Order Information Part Number IP7800A IP7800 IP140A IP140 LM140 K-Pack (TO-3) 3 3 3 3 3 R-Pack G/IG-Pack SMD 1 LCC4 (TO-66) (TO-257) SMD 05 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 Temp. Range -55 to +150C " " " " Note: To order, add the package identifier to the part number. eg. IP7805AK IP140SMD-12 Semelab Plc reserves the right to change test conditions, parameter limits and package dimensions without notice. Information furnished by Semelab is believed to be both accurate and reliable at the time of going to press. However Semelab assumes no responsibility for any errors or omissions discovered in its use. Semelab encourages customers to verify that datasheets are current before placing orders. Semelab plc. Telephone +44(0)1455 556565. Fax +44(0)1455 552612. E-mail: sales@semelab.co.uk Website: http://www.semelab.co.uk Document Number 2833 Issue 2