P R E L I M I N A R Y ZILOG Z16C32 IUSCTM PRELIMINARY PRODUCT SPECIFICATION Z16C32 IUSCTM INTEGRATED UNIVERSAL SERIAL CONTROLLER FEATURES Two Full-Capacity 20 MHz DMA Channels, Each with 32-Bit Addressing and 16-Bit Data Transfers. DMA Modes Include Single Buffer, Pipelined, ArrayChained and Linked-Array Chained. Ring Buffer Feature Supports Circular Queue of Buffers in Memory. Linked Frame Status Transfer Feature Writes Status Information for Received Frames and Reads Control Information for Transmit Frames to the DMA Channel's Array or Linked List to Significantly Simplify Processing Frame Status and Control Information. Programmable Throttling of DMA Bus Occupancy in Burst Mode with Bus Occupancy Time Limitation. 0 to 20 Mbit/sec, Full-Duplex Channel, with Two Baud Rate Generators and a Digital Phase-Locked Loop for Clock Recovery. 32-Byte Data FIFOs for Receiver and Transmitter Up to 12.5 MByte/sec (16-Bit) Data Bus Bandwidth Multiprotocol Operation Under Program Control with Independent Mode Selection for Receiver and Transmitter. Async Mode with One-to-Eight Bits/Character, 1/16 to Two Stop Bits/Character in 1/16 Bit Increments; 16x, 32x, or 64x Oversampling; Break Detect and Generation; Odd, Even, Mark, Space or No Parity and Framing Error Detection. Supports 9-Bit and MIL-STD1553B Protocols. HDLC/SDLC Mode with 8-Bit Address Compare; Extended Address Field Option; 16- or 32-Bit CRC; Programmable Idle Line Condition; Optional Preamble Transmission and Loop Mode. Selectable Number of Flags Between Back-to-Back Frames. Byte Oriented Synchronous Mode with One-to-Eight Bits/Character; Programmable Sync and Idle Line Conditions; Optional Receive Sync Stripping; Optional Preamble Transmission; 16- or 32-Bit CRC; Transmitto-Receive Slaving (for X.21). External Character Sync Mode for Receive Transparent Bisync Mode with EBCDIC or ASCII Character Code; Automatic CRC Handling; Programmable Idle Line Condition; Optional Preamble Transmission; Automatic Recognition of DLE, SYN, SOH, ITX, ETX, ETB, EOT, ENQ and ITB. Flexible Bus Interface for Direct Connection to Most Microprocessors; User Programmable for 8 or 16 Bits Wide. Directly Supports 680X0 Family or 8X86 Family Bus Interfaces. Receive and Transmit Time Slot Assigners for ISDN, T1 and E1 (CEPT) Applications. 8-Bit General-Purpose Port with Transition Detection Low Power CMOS 68-Pin PLCC Package Electronic Programmer's Manual Support Tool and Software Drivers are Available. GENERAL DESCRIPTION The Z16C32 IUSCTM (Integrated Universal Serial Controller) is a multiprotocol datacommunications device with onchip dual-channel DMA. The integration of a high-speed PS97USC0200 serial communications channel with high-performance DMA facilitates higher data throughput than can be achieved with discrete serial/DMA chip combinations. 1 ZILOG P R E L I M I N A R Y Z16C32 IUSCTM GENERAL DESCRIPTION (Continued) There are additional reasons for using the Z16C32 IUSC than just reduced chip count and board space economy. The DMA and serial channel intercommunication offers application benefits as well. For example, events such as the reception of the end of a HDLC frame is internally communicated from the serial controller to the DMA so that each frame can be written into a separate memory buffer. The buffer chaining capabilities, ring buffer support, automated frame status/control blocks, and buffer termination at the end of the frame combine to significantly reduce CPU overhead (Figure 1). The IUSC is software configurable to satisfy a wide variety of serial communication applications. The 20 Mbit/second data rate and multiple protocol support make it ideal for applications in today's dynamic environment of changing specifications and increasing speed. The many programmable features allow the user to tune the device response to meet system requirements and adapt to future requirements. The IUSC contains a variety of sophisticated internal functions including two baud rate generators, a digital phase-locked loop, character counters, and 32-byte FIFOs for both the receiver and the transmitter. The on-chip DMA channels allow high speed data transfers for both the receiver and the transmitter. The IUSC supports automatic status and control transfer through DMA and allows initialization of the serial controller under DMA control. Each DMA channel can do a 16-bit transfer in as little as three 50 ns clock cycles and can generate addresses compatible with 32-, 24- or 16-bit memory ranges. The DMA channels operate in any of four modes: single buffer, pipelined, array-chained, or linked-list. The array-chained and linked-list modes provide scatter-read and gather-write capabilities with minimal software intervention. To prevent the DMA from holding bus mastership too long, mastership time may be limited by counting the absolute number of clock cycles, the number of bus transactions, or both. The CPU bus interface is designed for use with any conventional multiplexed or non-multiplexed bus from manufacturers of CISC and RISC processors including Intel, Motorola, and Zilog. The bus interface is configurable for 16-bit data, 8-bit data with separate address or 8-bit 2 data without separate address to support multiplexed or non-multiplexed busses. The IUSC handles asynchronous formats, synchronous bit-oriented formats such as HDLC and synchronous byteoriented formats (e.g., BISYNC and DDCMP). This device supports virtually any serial data transfer application. The IUSC can generate and check CRC in any synchronous mode. Complete access to the CRC value allows system software to resend or manipulate the CRC as needed in various applications. The IUSC also provides facilities for modem control signals. In applications where these controls are not needed, the modem controls can be used for general-purpose I/O. Interrupts are supported by a daisy-chain hierarchy within the serial channel and between the serial channel and the DMA. Separate interrupt vectors for each type of interrupt within the serial controller and the DMA facilitate fast discrimination of the interrupt source. The IUSC supports Pulsed, Double Pulsed, and Status Interrupt Acknowledge cycles. Support tools are available to aid the designer in efficiently programming the IUSC. The Technical Manual describes in detail all the features and gives programming sequence hints. The Electronic Programmer's Manual, DC #8287-02, is an MS-DOS, disk-based programming initialization tool that can generate custom sequences. Also, Zilog offers assorted application notes and development boards to assist the designer in hardware and software development. Contact your nearest Zilog representative for additional information. Notes: All Signals with a preceding front slash, "/", are active Low, e.g.: B//W (WORD is active Low); /B/W (BYTE is active Low, only). Power connections follow conventional descriptions below: Connection Circuit Device Power Ground VCC GND VDD VSS PS97USC0200 P R E L I M I N A R Y ZILOG Host Processor Bus Interface Z16C32 IUSCTM 16-Bit Internal Data Bus Transmit DMA Interrupt Control Receive DMA Transmit FIFO Receive FIFO Serial Clock Logic Transmitter Time Slot Assigner DPLL Counters BRG0, BRG1 Receiver Time Slot Assigner I/O Port Figure 1. Z16C32 IUSC Block Diagram PS97USC0200 3 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM GENERAL DESCRIPTION (Continued) TxD RxD /TxC /RxC /CTS AD0 AD1 AD2 AD3 AD4 Address/ Data Bus Bus Timing Control Interrupt AD13 AD14 AD15 /AS /DS /RD /WR /CS S//D D//C R//W /INTACK /WAIT//RDY GND GND GND Ground /DCD /RxREQ /ABORT AD5 AD6 AD7 AD8 AD9 AD10 AD11 AD12 /BUSREQ /TxREQ B//W /UAS /INT Z16C32 IEI IEO PORT 0 PORT 1 PORT 2 PORT 3 PORT 4 PORT 5 PORT 6 PORT 7 /BIN /BOUT CLK /RESET VCC GND GND VCC VCC VCC VCC GND GND VCC VCC Serial Data Channel Clocks Channel I/O Channel DMA Interface Channel Interrupt Interface I/O Port System Clock Device Reset Power Figure 2. Z16C32 Pin Functions 4 PS97USC0200 ZiLO G NC NC NC /BIN NC /BUS REQ CLK /BOUT GND VCC AD8 AD9 AD10 AD11 AD12 AD13 AD14 AD15 GND VCC NC NC NC PORT 7 Z16C 32 IU SC TM 64 /UAS 60 55 50 45 65 41 40 PORT 6 /INTACK PORT 5 R/W PORT 4 /WR PORT 3 /RD PORT 2 /DS PORT 1 /AS PORT 0 VCC GND QFP 80 - Pin VCC GND NC /CTS /RESET TxD /CS /TxC D//C /DCD S//D RxD /Wait//RDY B//W /RxC 80 5 10 15 20 /TxREQ 24 NC NC NC /ABORT NC /INT IEI IEO GND VCC AD0 AD1 AD2 AD3 AD4 AD5 AD6 AD7 GND VCC /RxREQ NC NC NC 1 25 Figure 3. QFP 80-Pin Assignments 5 PRELIMINARY PS97U SC 0200 P R E L I M I N A R Y Z16C32 IUSCTM B//W /WAIT//RDY Reserved S//D D//C /CS /RESET VCC VCC VCC /AS /DS /RD /WR R//W /INTACK /UAS ZILOG 9 /ABORT /INT IEI IEO GND VCC AD0 AD1 AD2 AD3 AD4 AD5 AD6 AD7 GND VCC /RxREQ 1 68 61 10 60 IUSC 26 44 43 /TxREQ /RxC RxD /DCD /TxC TxD /CTS GND GND GND PORT 0 PORT 1 PORT 2 PORT 3 PORT 4 PORT 5 PORT 6 27 /BIN /BUSREQ CLK /BOUT GND VCC AD8 AD9 AD10 AD11 AD12 AD13 AD14 AD15 GND VCC PORT 7 Figure 4. Z16C32 68-Pin PLCC Pin Assignments PIN DESCRIPTION Figure 2 shows the logical pin groupings of the IUSC's pins, and Figure 3-4 shows the physical pin assignments. Only one strobe pin (/DS, /RD, /WR or Pulsed INTACK) should ever be active at one time. Any unused input pin (if an input when the IUSC is bus master or slave) must be pulled up to its inactive state. /RESET Reset (input, active Low). A Low on this line places the IUSC in a known, inactive state, and conditions it so that the data, from the next write operation that asserts the /CS pin, goes into the Bus Configuration Register (BCR) regardless of register addressing. /RESET should be driven Low as soon as possible during power-up, and as needed when restarting the overall system or the communications subsystem. CLK System Clock (input). This signal is the timing reference for the DMA and bus interface logic. (The serial controller section is clocked by the selected sources of receive and transmit clocking.) PS97USC0200 AD15-0 Address/Data Bus (inputs/tri-state outputs). After Reset, these lines carry data between the controlling microprocessor and the IUSC, and may also carry multiplexed addresses of registers within the IUSC. Such operation, between the host processor and the IUSC, is often called slave mode. Once the software has set up the device and placed it into operation, these lines also carry multiplexed addresses and data between the IUSC and system memory; such operation is called master mode. AD15-0 can be used in a variety of ways based on whether the IUSC senses activity on /AS after Reset, and on the data written to the Bus Configuration Register (BCR). /CS Chip Select (input, active Low). A Low on this line indicates that the controlling microprocessor's current bus cycle refers to a register in the IUSC. The IUSC ignores /CS when a Low on /INTACK indicates that the current bus operation is an interrupt acknowledge cycle. On a multiplexed bus the IUSC latches the state of this pin at rising edges on /AS; on a non-multiplexed bus, it latches /CS at leading/falling edges on /DS, /RD, or /WR. 6 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM Reset Any Transaction Up To and Including BCR Write No /AS At Least One /AS NonMultiplexed Bus BCR Write Transaction BCR[2]=0 BCR[15]=1 8-Bit With Separate Address BCR[2]=0 BCR[15]=0 8-Bit Without Separate Address Multiplexed Bus BCR[2]=1 16-Bit BCR[2]=0 BCR[15]=1 8-Bit With Separate Address BCR[2]=0 BCR[15]=0 8-Bit Without Separate Address BCR[2]=1 16-Bit Note: The presence of one transaction with an /AS active between reset, up to and including the BCR write, chooses a multiplexed type of bus. Figure 5. BCR Reset Sequence and Bit Assignments PS97USC0200 7 ZILOG P R E L I M I N A R Y /RD Read Strobe (input/tri-state output, active Low). This line indicates a read cycle on the bus, for host processors/ buses having this kind of signalling. It is an output when the IUSC has taken control of the bus and is operating in master mode, otherwise, it is an input that is qualified by /CS Low or /INTACK Low. For master read cycles, the IUSC captures data at the rising (trailing) edge of this line. For slave read cycles the IUSC provides valid data on the AD lines within the specified access time after this line goes Low, and keeps the data valid until after the master releases this line to High. /WR Write Strobe (input/tri-state output, active Low). This line indicates write cycles on the bus, for host processors/ buses having this kind of signalling. It is an output when the IUSC has taken control of the bus and is operating in master mode, otherwise it is an input that is qualified by /CS Low. For slave write cycles, the IUSC captures write data at the rising (trailing) edge of this line. For master write cycles, the IUSC places valid data on the AD lines before it drives this signal to Low , and keeps the data valid until after it drives this line back to High. B//W Byte / Word Select (tri-state output, High indicates 8-bit transfer). When the IUSC takes control of the bus and operates as a master, a High on this line indicates that a byte is to be transferred, and a Low indicates that 16 bits are to be transferred. The IUSC ignores this signal during slave cycles: it takes the byte/word distinction from an AD line at the rising edge of /AS, or from a bit in the serial or DMA Command/Address Register. /WAIT//RDY Wait, Ready, or Acknowledge handshaking (input/tri-state output, active Low). This line is an input when the IUSC has taken control of the bus and is operating in master mode. For slave cycles, the IUSC activates this line as an output. In both directions, the line can carry wait or acknowledge signalling depending on the state of the S//D input during the initial BCR write. If S//D is High when the BCR is written, this line operates as a Ready/Wait line for Zilog and most Intel processors. In this mode, the IUSC will not complete a master cycle while this line is Low, and it asserts this line Low until it's ready to complete an interrupt acknowledge cycle; it never asserts this line when the host accesses one of the IUSC registers. If S//D is Low when the BCR is written, this line operates thereafter as an Acknowledge line for Motorola and some Intel processors. In this mode, the IUSC will not complete a master cycle until this line is Low. It asserts this line Low for register read and write cycles, and when it is ready to complete an interrupt acknowledge cycle. PS97USC0200 Z16C32 IUSCTM For slave cycles, this is a full time (totem pole) output. The board designer can combine this signal with similar signals from other slaves, by means of an external logic gate or a tri-state or open-collector driver. /INT Interrupt Request (output, active Low). The IUSC drives this line Low when (1) its IEI pin is High, (2) one or more of its interrupt condition(s) is (are) enabled and pending, and (3) the Under Service flag is not set for its highest priority enabled/pending condition, nor for any higher-priority internal condition. Software can program whether the bus interface drives this pin in a totem-pole or an open-drain fashion. /INTACK Interrupt Acknowledge (input, active Low). A Low on this line indicates that the host processor is performing an interrupt acknowledge cycle. In some systems, a Low on this line may further indicate that external logic has selected this IUSC as the device to be acknowledged, or as a potential device to be acknowledged. A field in the Bus Configuration Register selects whether this line carries a level-sensitive "status" signal that the IUSC should sample at the leading edge of /AS or /DS, or a single-pulse or double-pulse protocol. The IUSC responds to an interrupt acknowledge cycle in a variety of ways depending on this programming and the state of the /INT and IEI lines, as described in the text. IEI Interrupt Enable In (input, active High). This signal and the IEO pin can be part of an interrupt-acknowledge daisy chain with other devices that may request interrupts. If IEI is High outside of an interrupt acknowledge cycle, one or more IUSC interrupt condition(s) is (are) enabled and pending, and the Under Service flag isn't set for the highest priority condition nor for any higher-priority one, then the IUSC requests an interrupt by driving its /INT pin Low. If the IEI pin is High during an interrupt acknowledge cycle, one or more IUSC interrupt condition(s) is (are) enabled and pending, and the Under Service flag isn't set for the highest priority condition nor for any higher-priority, then the IUSC keeps IEO Low and responds to the cycle. IEO Interrupt Enable Out (output, active High). This signal and/or IEI can be part of an interrupt acknowledge daisy chain with other devices that may request interrupts. The IUSC drives its IEO pin Low whenever its IEI pin is Low, and/or if the Under Service flag is set for any condition. This IUSC drives this signal slightly differently during an interrupt acknowledge cycle, in that it also forces IEO Low if it is (has been) requesting an interrupt. 8 ZILOG P R E L I M I N A R Y Z16C32 IUSCTM PIN DESCRIPTION (Continued) /BUSREQ Bus Request (output, active Low). The DMA controller section drives this line Low to request control of the host bus. /BUSREQ can be an open-drain or totempole output depending on a bit in the Bus Configuration Register. In open-drain mode the IUSC samples the pin as an input and only drives it Low after sampling it high. /TxC Transmit Clock (input or output). This signal can be used as a clock input for any of the functional blocks in the serial controller. Or, software can program the IUSC so that this pin is an output carrying any of several transmitter or internal clock signals, a general purpose input or output, or an interrupt input. /BIN Bus Acknowledge In (input, active Low). When the IUSC receives a falling edge on this input, it samples whether it has been driving (or has just begun to drive) /BUSREQ. If so, it keeps /BOUT High and takes control of the host bus. If not, it passes the bus grant by driving /BOUT Low. This signal can be used with /BOUT to form a bus-grant daisy chain for arbitration of bus control. Alternatively, it can be connected to a direct, positive grant from an external arbiter, and the /BOUT pin can be left unconnected. /RxREQ Receive DMA Request (input or output). In device testing or in applications not using the serial controller and DMA controller sections together in the usual way, this pin can carry an active Low DMA Request from the receive FIFO. On the IUSC this request is internally routed to the on-chip Receive DMA channel; it is more typical to use the RxREQ pin as a general-purpose output or as an interrupt input. /BOUT Bus Acknowledge Out (output, active Low). As noted above, this signal can be used with /BIN to form a bus-grant daisy chain for arbitration of bus control. /ABORT Abort Master Cycle (input, active Low ). A Low on this line during a master cycle makes the currently active DMA channel terminate its activity and enter a disabled state. Note that /ABORT is only effective during a DMA cycle, so that the IUSC knows which channel should be aborted. Also note that external logic must set /WAIT//RDY to the right state for the cycle to complete, before /ABORT becomes effective. /TxREQ Transmit DMA Request (input or output). In device testing or in applications not using the serial controller and DMA controller sections together in the usual way, this pin can carry an active Low DMA Request from the transmit FIFO. On the IUSC this request is internally routed to the on-chip Transmit DMA channel, and it's more typical to use the RxREQ pin as a general-purpose output or as an interrupt input. /DCD Data Carrier Detect (input or output, active Low). Software can program the IUSC so that this signal enables/ disables the receiver. In addition, software can program the device to request interrupts in response to transitions on this line. The pin can also be used as a simple input or output. RxD Received Data (input, positive logic). The serial input. TxD Transmit Data (output, positive logic). The serial output. /RxC Receive Clock (input or output). This signal can be used as a clock input for any of the functional blocks in the serial controller. Or, software can program the IUSC so that this pin is an output carrying any of several receiver or internal clock signals, a general-purpose input or output, or an interrupt input. 9 /CTS Clear to Send (input or output, active Low). Software can program the IUSC so that this signal enables/disables the transmitter. In addition, software can program the device to request interrupts in response to transitions on this line. The pin can also be used as a simple input or output. PS97USC0200 ZILOG P R E L I M I N A R Y Z16C32 IUSCTM PORT7/TxCOMPLT General-Purpose I/O or Transmit Complete (input or output). Software can program the IUSC so that this pin is a general-purpose input or output, or so that it carries a Transmit Complete signal from the Transmitter, that can control an external driver. The IUSC captures transitions on this pin in internal latches. PORT 3/RxTSA General-Purpose I/O or Receive Time Slot Assigner Gate (input or output). Software can program the IUSC so that this pin is a general-purpose input or output, or so that it carries the Gate output of the Receive Time Slot Assigner. The IUSC captures transitions on this pin in internal latches. PORT6/FSYNC General-Purpose I/O or Frame Sync (input or output). Software can program the IUSC so that this pin is a general-purpose input or output, or a Frame Sync input for the IUSC's Time Slot Assigner circuits. The IUSC captures transitions on this pin in internal latches. PORT 2 General-Purpose I/O (input or output). Software can program the IUSC so that this pin is a general-purpose input or output. The IUSC captures transitions on this pin in internal latches. PORT5/RxSYNC General-Purpose I/O or Receive Sync (input or output). Software can program the IUSC so that this pin is a general-purpose input or output, or so that it carries a Receive Sync output from the Receiver. The IUSC captures transitions on this pin in internal latches. PORT4/TxTSA General-Purpose I/O or Transmit Time Slot Assigner Gate (input or output). Software can program the IUSC so that this pin is a general-purpose input or output, or so that it carries the Gate output of the Transmit Time Slot Assigner, that can enable an external TxD driver in timeslotted ISDN or Fractional T1 applications. The IUSC captures transitions on this pin in internal latches, as described in the text. PORT 1-0/CLK 1-0 General-Purpose I/Os or Reference Clocks (inputs or outputs). Software can program the IUSC so that either of these pins is a general-purpose input or output, or a reference clock that can be divided down to derive clocking for the Receiver and/or Transmitter. When one of these pins is a general-purpose I/O, the IUSC captures transitions on it in internal latches. VCC, VSS Power and Ground. The inclusion of seven pins for each power rail ensures good signal integrity, prevents transients on outputs, and improves noise margins on inputs. The IUSC's internal power distribution network requires that all these pins be connected appropriately. ARCHITECTURE The IUSC integrates a fast and efficient dual-channel DMA with a highly versatile serial communications controller. The functional capabilities of the IUSC are described from two different points of view; as a datacommunications device, it transmits and receives data in a wide variety of datacommunications protocols; as a microprocessor peripheral with two DMA channels that offer such features as PS97USC0200 four DMA transfer types, a flexible bus interface, and vectored interrupts. The architecture is described in three sections, DMA and Bus Interface Capabilities, Communication between the DMA and Serial Channel, and Serial Communication Capabilities. The structure of the IUSC is shown in Figure 1. 10 ZILOG P R E L I M I N A R Y Z16C32 IUSCTM DMA AND BUS INTERFACE CAPABILITIES The IUSC's two versatile DMA channels combined with a flexible bus interface gives it the ability to meet a wide variety of application requirements. The time required to move data into and out of the transmitter and receiver is minimized by the IUSC's speed (20 MHz clock, three clock cycles per word, typical); two buffer-chaining modes with linked-frame status transfer; early buffer termination to keep received frames in separate memory buffers; and vectored interrupts. Some of the these features are briefly described below, however, the user should refer to the IUSC Technical Manual for additional information. DMA Modes The IUSC contains two DMA channels, one for the transmitter and one for the receiver. Each channel supports a 32-bit address and a 16-bit byte count. The channels operate in one of four modes. In normal mode, the processor must reload the address and length at the end of each buffer. In Pipelined mode, the processor can load the address and length of the next buffer at any time during the DMA transfer to the first buffer. In Array-Chained mode the processor creates a table of address/length pairs in memory for automatic transfer by the channel. In Linked List mode the processor creates a linked list of address and length pairs in memory to be automatically transferred by the channel. Single Buffer Mode is the most basic of the four data transfer types. The starting address of each memory buffer and the maximum number of characters to be transferred to or from memory are programmed into the IUSC registers. When the DMA is enabled, it transfers all data between system memory and the transmit and receive FIFOs. Pipelined Mode is similar to Single Buffer Mode with the addition of an extra set of registers into which the processor can load to reload the DMA with the address and count of the next memory buffer. Therefore, when a buffer is complete, the IUSC is pre-programmed with the address and count of the next buffer so the DMA need not stop between each buffer as long as software stays one step ahead of memory buffer usage. In Array Mode, one of the two chaining modes, software sets up a table of memory buffer information. The length of the array is only limited by the amount of system memory available for buffers. The IUSC is programmed with the location of the array of buffer addresses and sizes. This mode has the advantage that a burst of short frames is less 11 likely to overrun the systems ability to keep up. The use of receive status block and transmit control block along with the early buffer termination feature simplifies the segmentation and reassembly of serial messages in memory buffers. When a DMA channel fetches a buffer count of zero, it stops and can create an End-Of-Array interrupt. Linked List Mode is the most versatile of DMA modes. It has the Array Mode's ability to switch buffers rapidly without the requirement for the buffer information to be in a continuous table. Each link entry contains: The starting address to write or read the data; the size of the buffer; optional status or control information; and a pointer to the next link. Memory buffers can easily be added and removed from the list by changing the links in list entries. DMA Features In Linked List Mode, the IUSC has a programmable feature to facilitate the use of buffers in a ring. When this feature is enabled, the DMA writes a zero back to the buffer length field of each array or list entry after it is read. Therefore, if a linked list wraps around on itself, a DMA channel will not reuse a buffer until software has processed the buffer, and indicated that its eligible for reuse by writing a nonzero value in the count field (fetching a count value of zero deactivates the DMA channel). This feature can also be used in array mode to track buffer use. In both Bus Slave and Master Modes, the IUSC can read and write data words in either byte order. It supports the Little Endian convention used by many Intel microprocessors and the Big Endian convention used by many Motorola microprocessors. When the IUSC is bus master, it can be programmed to generate only the upper 16-bit address when required and, consequently, save a clock cycle on each transfer (three clocks per transfer instead of four). When using the IUSC on a 16-bit bus and the starting address of the message is on an odd address, the IUSC automatically reorients itself onto even word boundaries by first fetching a byte. This is especially valuable when retransmitting a frame with a different size header than was received. Two pins are available as status signals of the type of transfer in progress. There are a variety of command and status registers to control and monitor the DMA channels. A DMA channel can be aborted with either the /ABORT pin or by software command. A pause command is also available to temporarily suspend transfers. PS97USC0200 ZILOG P R E L I M I N A R Y Z16C32 IUSCTM Bus Interface & Utilization Interrupts The bus interface module stands between the external bus pins and an on-chip 16-bit data bus that interconnects the other functional modules. It includes several flexible bus interfacing options that are controlled by the contents of the Bus Configuration Register (BCR). The BCR is automatically the destination of the first write to the IUSC by the host processor after a reset. The interrupt subsystem of the IUSC derives from Zilog's experience in providing the most advanced interrupt capabilities in the microprocessor field. These capabilities are at their best when used with a Zilog microprocessor, but it is easy to interface the IUSC to work well with other microprocessors as well. Four pins are dedicated to create an interrupt daisy-chain hierarchy within the Serial Channel and between the Serial Channel and the DMA. The IUSC is compatible with both multiplexed and nonmultiplexed bus interfaces and can transfer either 8 or 16 bits. It supports data transfers with /RD and /WR or R//W and /DS strobe pins and either format of byte ordering. The IUSC generates the Wait or Ready acknowledge handshaking used by Intel or Motorola microprocessors. Also, three styles of interrupt acknowledge signals are supported for automated return of an interrupt vector to any common microprocessor. There are several options that control how the IUSC uses the bus. The /BIN and /BOUT pins are available to form a bus-grant daisy chain. The IUSC has several options on how it arbitrates requests for bus mastership between channels and how long it stays off the bus between requests. The priority of the two DMA channels is programmable and can alternate between requests to allow both channels equal access to the bus. Once one of the channels has mastership of the bus, control can be passed to the other channel if it is requesting or the IUSC can be forced off the bus. A programmable preempt feature selects whether the higher priority channel can take over control of the bus if it starts requesting control while the lower priority channel is using the bus. The IUSC maximizes the use of its 32-byte FIFOs by holding /BUSREQ active until the transmit FIFO is full, the receive FIFO is empty, or both. The programmable dwell timers can be used to limit how long the IUSC holds bus mastership by counting either bus transfers, clock cycles or both. Therefore, the combination of programmable FIFO request levels, channel arbitration options, and programmable dwell timer features provide application software the flexibility to optimize the IUSCs bus occupancy to meet system throughput and bus response requirements. When an IUSC responds to an interrupt acknowledge from the CPU, it places an interrupt vector on the data bus. To speed interrupt response time, the IUSC modifies three bits in the vector to indicate which type of interrupt is being requested. Separate vectors are provided for the serial channel and DMA to easily discriminate the interrupt source. The DMA has four interrupt sources each for the receive and transmit channels. Each interrupt source is independently enabled and there is a master enable for all DMA interrupts. The four interrupt sources are End Of Array/ End of Link, End Of Buffer, Hardware Abort, and Software Abort. Each of the six types of interrupts in the serial portion IUSC (Receive Status, Receive Data, Transmit Status, Transmit Data, I/O Status and Device Status) has three bits associated with it: Interrupt Pending (IP), Interrupt-Under-Service (IUS) and Interrupt Enable (IE). If the IE bit for a given source is set, then that bit can source request interrupts. Note that individual sources within the six types also have their own interrupt arm bits. Finally, there is a Master Interrupt Enable (MIE) bit which globally enables or disables all interrupts from the serial channel. The Interrupt (/INT), Interrupt Acknowledge (/INTACK), Interrupt Enable In (IEI) and Interrupt Enable Out (IEO) pins are provided to create an automated mechanism to place the vector on the bus among the highest priority pending interrupts from multiple devices. The device with the highest pending interrupt (/INT Low, IEI High) places a vector on the bus in response to an interrupt acknowledge cycle. In the IUSC, the IP bit signals that an interrupt is pending. If an IUS bit is set, this interrupt is being serviced and all interrupt sources of lower priority are prevented from requesting interrupts. An IUS bit is set during an interrupt acknowledge cycle if there are no higher priority devices requesting interrupts. PS97USC0200 12 ZILOG P R E L I M I N A R Y Z16C32 IUSCTM DMA AND BUS INTERFACE CAPABILITIES (Continued) There are six sources of Receive Status interrupt. Each one is individually armed: Receiver exited hunt, received idle line, received break/abort, received code violation/end-oftransmission/end-of-message, parity error/abort and overrun error. The Receive Data interrupt is generated whenever the receive FIFO fills with data beyond the level programmed in the Receive Interrupt Control Register (RICR). There are six sources of Transmit Status interrupt. Each one is individually armed: Preamble sent, idle line sent, abort sent, end-of-frame/end-of-message sent, CRC sent and underrun error. The Transmit Data interrupt is generated whenever the transmit FIFO empties below the level programmed in the Transmit Interrupt Control Register (TICR). The I/O Status interrupt serves to report transitions on any of six pins. Interrupts are generated on either or both edges with individual edge selection and arming for each pin. The pins that can be programmed to generate I/O Status interrupts are /RxC, /TxC, /RxREQ, /TxREQ, /DCD and /CTS. These interrupts are independent of the programmed function of the pins. The Device Status interrupt has four individually enabled sources: Receive character counter underflow, DPLL sync acquired, BRG1 zero count and BRGO zero count. Refer to the IUSC Technical Manual for more details. COMMUNICATION BETWEEN THE DMA AND SERIAL CHANNELS The IUSC's intra-chip communication between the DMA and serial communications controller gives it the power to achieve higher efficiency than is possible with a separate DMA controller. The Linked Frame Status Transfer feature writes the status and byte count of each received frame to memory as part of an array or linked list. This provides a simple and easy to use mechanism for storing the results of a received message without arbitrary restrictions on how quickly the host software must examine the results. Similarly, control information for transmit frames can be automatically read by the DMA from the array or link and transferred into registers in the serial logic. In all modes, the DMA can accept a signal from the serial channel for early buffer termination. When the end of a message is received, the data is transferred to the buffer and the status is written to memory. The status is written after the data in single buffer and pipelined modes or to the array/link in array and linked-list modes if Linked-Frame Status Transfer is enabled. This early buffer termination is 13 treated identically to the terminal count condition in the DMA. Therefore, the receipt of the end of a message is a seamless transition from one memory buffer to the next. An example of using these intercommunication features using linked list mode is shown in Figure 5. This example shows the format of a ring of memory buffers with the linked frame status transfer and ring buffer features enabled. Any protocol that sets the "RxBound" bit (RCSR4 = 1), like HDLC or 802.3, is appropriate to this example. The linked list is shown in Figure 5 with three links for simplicity and may be as large as memory allows. The sixth word in each list entry is reserved and should not be used (it keeps the list entries on 32-bit boundaries). If the end of the buffer is reached and it is not the end of the frame, the IUSC writes zeros as the status and count. Also, if the transmit channel needs to start a new memory buffer other than at the beginning of a frame, the DMA ignores the transmit control block. PS97USC0200 P R E L I M I N A R Y ZILOG Buffer 1 Address Buffer 1 Length Buffer 1 RSBR or 0 Buffer 1 RSHR or 0 0 Z16C32 IUSCTM Buffer 3 Address Ring Buffer Mode Writes this word to 0 after it is read. Buffer 3 Length Buffer 3 RSBR or 0 Integrated Frame Status Transfer writes the Receive Status Block (or 0) here. Link Address of Entry2 Buffer 3 RSHR or 0 0 Link Address of Entry1 Buffer 2 Address Buffer 2 Length Buffer 2 RSBR or 0 Buffer 2 RSHR or 0 0 Link Address of Entry3 Figure 5. Linked List Mode with Linked Frame Status Transfer and Ring Buffer Features Another method by which the DMA and serial channel work together is using the Transmit Character Counter to break a large block of data into a number of fixed length frames. For example, it is desired to transmit a large file which is located in several memory buffers as fixed length smaller frames. With the IUSC, the serial channel is programmed to send the end-of-frame sequence each time the set number of bytes is transmitted. Therefore, DMA transfers are not interrupted, nor is system response required to break the large file into frames. PS97USC0200 The IUSC provides higher throughput than discrete serial and DMA chip solutions because discrete chips do not directly communicate with each other and, therefore, the status of one device must be read by the CPU and communicated to the other. This typically requires interrupts and the suspension of activity until status/control information is updated. This uses precious time and bus bandwidth, which can limit total throughput. 14 ZILOG P R E L I M I N A R Y Z16C32 IUSCTM DATA COMMUNICATIONS CAPABILITIES The IUSC provides a full-duplex channel programmable for use in any common data communication protocol. The receiver and transmitter are completely independent and each is supported by a 32-byte deep FIFO and a 16-bit frame length counter. All modes allow optional even, odd, mark or space parity. Synchronous modes allow the choice of either of two 16-bit or a 32-bit CRC polynomials. Character length of up to 8 bits can be programmed for the receiver and transmitter independently. Error and status conditions are carried with the data in the receive FIFO to greatly reduce the CPU overhead required to send or receive a message, while key control parameters accompany transmit characters through the Tx FIFO. Interrupts can be individually armed to signal such conditions as overrun, parity error, framing error, end-of-frame, idle line received, sync acquired, transmit underrun, CRC sent, closing sync/flag sent, abort sent, idle line sent and preamble sent. In addition, several useful internal signals like receive character boundary, received sync, transmit character boundary and transmission complete can be sent to pins for use by external circuitry. Protocols Asynchronous Mode. The receiver and transmitter handle data at a rate of 1/16, 1/32, or 1/64 the clock rate. The receiver rejects start bits less than one-half a bit time and includes recovery logic following a framing error. The transmitter is capable of sending one, two, or anywhere in the range of 9/16th to two stop bits per character in 1/16 bit increments. Nine-Bit Mode. This mode is identical to async except that the receiver checks for the status of an additional address/ data bit between the parity bit and the stop bit. The value of this bit is FIFO'ed along with the data. In the transmitter, this bit is automatically inserted with the value that is FIFO'ed from the transmit data. Isochronous Mode. Both transmitter and receiver operate on start-stop (async) data using a 1x clock. The transmitter sends one or two stop bits. Asynchronous With Code Violations. This is similar to Isochronous mode except that the start bit is replaced by a three bit-time code violation pattern as in MIL-STD1553B. The transmitter sends zero, one or two stop bits. HDLC Mode. In this mode, the receiver recognizes flags, performs optional address matching, accommodates extended address fields, and performs zero deletion and CRC checking. The receiver is capable of receiving sharedzero flags, recognizes abort sequences and can receive arbitrary length frames. The transmitter automatically sends 15 opening and closing flags, performs zero insertion and can be programmed to send an abort, an extended abort, a flag or CRC and a flag on transmit underrun. The transmitter automatically sends a closing flag with optional CRC at the end of a programmed message length. Sharedzero flags are selected in the transmitter and a separate character length is programmed for the last character in the frame. Frames terminated with an ABORT can be marked with a status bit on the preceding character in addition to the status interrupt that can be enabled. Abort is only detected in-frame and, therefore, eliminates false detection due to an idle line. The IUSC provides four choices (flag, all 1s, all 0s, or alternating 1s and 0s) of line preamble to condition the line before beginning data transmission. This feature is valuable to get the receiver DPLL in sync and as a flow control mechanism to slow down frame transmission without slowing down the clock or disabling the transmitter. HDLC Loop Mode. This mode is available only in the transmitter and allows the IUSC to be used in an HDLC Loop configuration. In this mode, the receiver is programmed to operate in HDLC mode to allow the transmitter to echo received messages. Upon receipt of a particular bit pattern (actually a sequence of seven consecutive ones) the transmitter stops repeating data and inserts its own frame(s). 802.3 Mode. This mode implements the data format of IEEE 802.3 with a 16-bit address compare. In this mode, /DCD and /CTS are used to implement the carrier sense and collision detect interactions with the receiver and transmitter. Back-off timing must be provided externally. Monosync Mode. In this mode, a single character is used for synchronization. The sync character can be either eight bits long or the same length as the data characters. The receiver can automatically strip sync characters from the received data stream. The transmitter is programmed to automatically send CRC on either an underrun or at the end of a programmed message length. Slaved Monosync Mode. This mode is available only in the transmitter and allows the transmitter (operating just as though it were in monosync mode) to send data with its byte boundaries synchronized to those of the received data. Bisync Mode. This mode is identical to monosync mode except that character synchronization requires two successive characters. The two characters need not be identical. PS97USC0200 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM Transparent Bisync Mode. In this mode, the synchronization pattern is DLE-SYN, programmable selected from either ASCII or EBCDIC encoding. The receiver recognizes control character sequences and automatically handles CRC calculations without CPU intervention. The transmitter is programmed to send either SYN, DLE-SYN, CRC-SYN, or CRC-DLE-SYN upon underrun and automatically sends the closing DLE-SYN with optional CRC at the end of a programmed message length. NRZI-Space. In NRZI-Space, a 1 is represented by the absence of a transition at the beginning of a bit cell, i.e., the level present in the preceding bit cell is maintained. A 0 is represented by a transition at the beginning of the bit cell. External Sync Mode. The receiver is synchronized to the receive data by an externally-supplied signal on a pin for custom protocol applications. Biphase-Space. In Biphase-Space, a 1 is represented by a transition at the beginning of the bit cell only. A 0 is represented by a transition at the beginning of the bit cell and another transition at the center of the bit cell. Data Encoding The IUSC is programmed to encode and decode the serial data in any of eight different ways (Figure 6). The transmitter encoding method is selected independently of the receiver decoding method. NRZ. In NRZ, a 1 is represented by a High level for the duration of the bit cell and a 0 is represented by a Low level for the duration of the bit cell. NRZB. NRZB is inverted from NRZ. NRZI-Mark. In NRZI-Mark, a 1 is represented by a transition at the beginning of a bit cell, i.e., the level present in the preceding bit cell is reversed. A 0 is represented by the absence of a transition at the beginning of the bit cell. Data 1 1 0 Biphase-Mark. In Biphase-Mark, a 1 is represented by a transition at the beginning of the bit cell and another transition at the center of the bit cell. A 0 is represented by a transition at the beginning of the bit cell only. Biphase-Level. In Biphase-Level, a 1 is represented by a High during the first half of the bit cell and a Low during the second half of the bit cell. A 0 is represented by a Low during the first half of the bit cell and a High during the second half of the bit cell. Differential Biphase-Level. In Differential Biphase-Level, a 1 is represented by a transition at the center of the bit cell, with the opposite polarity from the transition at the center of the preceding bit cell. A 0 is represented by a transition at the center of the bit cell with the same polarity as the transition at the center of the preceding bit cell. In both cases, there are transitions at the beginning of the bit cell to set up the level required to make the correct center transition. 0 1 0 NRZ NRZB NRZI-M NRZI-S BI-PHASE-M BIPHASE-S BIPHASE-L DIFFERENTIAL BIPHASE-L Figure 6. Data Encoding PS97USC0200 16 ZILOG P R E L I M I N A R Y Z16C32 IUSCTM DATA COMMUNICATIONS CAPABILITIES (Continued) Character Counters The IUSC contains separate 16-bit character counters for the receiver and transmitter. The receive character counter is set to a programmable starting value or automatically at the beginning of each received frame and can be reloaded under software control during a frame. The counter decrements with each receive character. At the end of the receive message the current value in the counter is automatically loaded into a four-deep FIFO. With the Receive Status Block (RSB) feature enabled, the counter value and the status (RCSR) can be automatically transferred to memory following the data. In array and linked list modes, the RSB can be transferred to the array or list entry for easy software access. This allows DMA transfer of data to proceed without CPU intervention at the end of a received frame, as the values in the FIFO allow the CPU to determine the status and length of each frame. to the Baud Rate Generator can be the /TxC pin, the /RxC pin, a PORT pin, or the output of either counter. The baud rate generator output frequency is related to the baud rate generator input clock frequency by the following formula: Similarly, the transmit character counter is loaded automatically at the beginning of each transmit frame and can be reloaded under software control during a frame. The counter is decremented with each write to the transmit FIFO. When the counter reaches zero, and that byte is sent, the transmitter automatically terminates the message in the appropriate fashion (usually by sending the CRC and the closing flag or sync character) without requiring CPU intervention. In linked list and array modes, the transmit character count and frame control word can be fetched from the linked list or array. The IUSC contains a DPLL (Digital Phase-Locked Loop) to recover clock information from a data stream with NRZI or Biphase encoding. The DPLL is driven by a clock that is nominally 8, 16 or 32 times the receive data rate. The DPLL uses this clock, along with the data stream, to construct a clock for the data. This clock can be routed to the receiver, transmitter, or both, or to a pin for use externally. In all modes, the DPLL counts the input clock to create nominal bit times. While counting, the DPLL watches the incoming data stream for transitions. When a transition is detected, the DPLL may make a count adjustment (during the next counting cycle) to produce an output clock which tracks the incoming bit cells. The DPLL provides properly phased transmit and receive clocks to the clock multiplexer. Baud Rate Generators The IUSC contains two Baud Rate Generators. Each generator consists of a 16-bit time constant register and a 16bit down counter. In operation, the counter decrements with each cycle of its selected input clock, and the time constant can be automatically reloaded when the count reaches zero. The output of the Baud Rate Generator toggles when the counter reaches a count of one-half of the time constant and again when the counter reaches zero. A new time constant can be written at any time but the new value does not take effect until the next load of the counter. The outputs of both baud rate generators are sent to the clock multiplexer for use internally or externally. The input 17 Output frequency = Input frequency/time constant + 1. Note: This allows an output frequency in the range of 1 to 1/65536 of the input frequency, inclusive. The output of either Baud Rate Generator can be used as the transmit or receive clock, the reference clock input to the DPLL circuit, and/or can be output on the /RxC or /TxC pin. Digital Phase-Locked Loop Counters The IUSC contains two 5-bit counters, which are programmed to divide an input clock by 4, 8, 16 or 32. The outputs of these two counters are sent to the clock multiplexer. The counters can be used as prescalers for the Baud Rate Generators. They also provide a stable transmit clock from a common source when the DPLL is providing the receive clock. The PORT0 and PORT1 pins can be used as inputs to the counters. PS97USC0200 ZILOG P R E L I M I N A R Y Z16C32 IUSCTM Clock Multiplexers I/O Port The clock multiplexer logic selects the receive and transmit clocks and optional outputs on the /RxC and/or /TxC pin(s). In the Z16C32, the PORT0 and PORT1 pins can be used directly as receive and transmit clocks, as well as being used as inputs to the counters. The Port pins are general-purpose I/O pins. They are used as additional modem control lines or other I/O functions. Each port bit is individually programmable as generalpurpose input, as an output, or for a dedicated input or output function. This programming is done in the Port Control Register. Whether used as inputs or outputs, the port pins can be read at any time. Time Slot Assigner The IUSC is equipped with two Time Slot Assigners to support ISDN and Fractional T1 communications. There is one assigner for the receiver. Each time slot assigner selects one or more time slots within a frame, however, the selected time slots must be contiguous. The first selected time slot is programmable from slot 0 (the first slot) to slot 127 of the frame. The number of concatenated slots is programmable from 1 to 15 (total slots). The time of the first slot can be offset an integral number of clocks. This offset is a delay and is programmable from 0 (no offset) to 7 clocks in increments of one clock (one bit cell). This offset can be used to compensate for delays in frame sync detection logic. The dedicated functions of the port pins include Time Slot Assigner gate outputs, transmit complete output, clock inputs, receive sync output, or frame sync input. Test Modes The Latched/Unlatch bit is held at 0 if no transitions occur on the port pin; this bit is set to a 1 when a rising edge or falling edge transition is detected, or immediately after the latch is opened if one or more transitions occurred while the latch was closed. Writing a 0 to the Latched/Unlatch bit has no effect on the latch. Writing a 1 to this bit resets the status bit and opens the latch. To use the port as an input without edge detection, a 1 would be written to the Latched/ Unlatch bit to open the latch and then the Port Status Register would be read to obtain the current pin input status. The IUSC can be programmed for local loopback or auto echo operation. In local loopback, the output of the transmitter is internally routed to the input of the receiver. This allows testing of the IUSC data paths without any external logic. Auto echo connects the RxD pin directly to the TxD pin. This is useful for testing serial links external to the IUSC. PS97USC0200 The port pins capture edge transitions. Programming for the capture is done using the Port Latched/Unlatch command bits in the Port Status Register. Each port bit is individually controlled. The Latched/Unlatch bit is used as a status signal to indicate that a transition has occurred on the port pin and as a command to open the latches that capture this transition. Both rising edge and falling edge are detected. When a transition is detected, the latch closes, holding the post transition state of the input. 18 ZILOG P R E L I M I N A R Y Z16C32 IUSCTM PROGRAMMING An Electronic Programmer's Manual (MS DOS based) and a Technical Manual are available to provide details about programming the IUSC. Also included are explanations and features of all registers in the IUSC. The registers in the IUSC are programmed by the system to configure the channel. Before this can occur, the system must set up the bus interface by writing to the Bus Configuration Register (BCR). The BCR has no specific address and is only accessible after a hardware reset of the device. The first write to the IUSC, after a hardware reset, programs the BCR. From that time on other channel registers can be accessed. No specific address need be presented to the IUSC for the BCR write; the IUSC knows that the first write after a hardware reset is destined for the BCR. In the multiplexed bus case, all registers are directly addressable through the address latched by /AS at the beginning of each bus cycle. The D//C pin is still used to directly access the receive and send data registers (RDR and TDR) with a multiplexed bus; if D//C is High, the address latched by /AS is ignored and an access of RDR or TDR is performed. In the non-multiplexed bus case, the channel registers are accessed indirectly using the address pointer in the Channel Command/Address Register (CCAR). The address of the desired register is first written to the CCAR and then the selected register is accessed; the pointer in the CCAR is automatically cleared after this access. 19 Two more points about the IUSC should be noted here. Channel Reset bit in the CCAR places the channel in the reset state. To exit this reset state either a word of all zeros is written to the CCAR (16-bit bus) or a byte of all zeros is written to the lower byte of the CCAR (8-bit bus). Secondly, after reset, the transmit and receive clocks are disabled. The first thing that should be done in any initialization sequence is a write to the Clock Mode Control Register (CMCR) to select a clock source for the receiver and transmitter. The Serial/DMA (S//D) pin is used to differentiate between the serial channel and the DMA registers. The DMA registers fall into three logic groupings; common registers that apply to both transmit and receive, transmit registers, and receive registers. The registers for DMA transmit functions and receive functions are symmetric and therefore, a single diagram is shown for each in the following pages. When addressing the DMA registers, the Data/Control (D/ /C) pin selects between the transmit and receive registers. For example, there is a DMA byte count register for transmit and receive (TBCR and RBCR) at address 10101 with S//D pin Low. The TBCR is selected with the D//C pin Low, and the RBCR is selected with the D//C pin High. The format of these two registers is shown in Figure 21. The register addressing is shown in Table 2 and the table assumes that the BCR register bit 0 is set to 1. The A5-A1 column in the Table reflects the state of AD5-AD1, AD13AD9, CCAR5-CCAR1 or DCAR5-DCAR1 as applicable. The bit assignments of the registers are shown in Figures 8 through 81. See the IUSC Technical Manual for details. The register addressing is shown in Table 2 and the bit assignments for the registers are shown in Figure 7. PS97USC0200 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM Reset Any Transaction Up To and Including BCR Write No /AS At Least One /AS NonMultiplexed Bus BCR Write Transaction BCR[2]=0 BCR[15]=1 8-Bit With Separate Address BCR[2]=0 BCR[15]=0 8-Bit Without Separate Address Multiplexed Bus BCR[2]=1 16-Bit BCR[2]=0 BCR[15]=1 8-Bit With Separate Address BCR[2]=0 BCR[15]=0 8-Bit Without Separate Address BCR[2]=1 16-Bit Note: The presence of one transaction with an /AS active between reset, up to and including the BCR write, chooses a multiplexed type of bus. Figure 7. BCR Reset Sequence and Bit Assignments PS97USC0200 20 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM PROGRAMMING (Continued) Table 1. Register Address List S//D D//C Address A5-A1 Name Description 1 1 1 1 0 0 0 0 00000 00001 00010 00011 CCAR CMR CCSR CCR Channel Command/Address Register Channel Mode Register Channel Command/Status Register Channel Control Register 1 1 1 1 0 0 0 0 00100 00101 00110 00111 PSR PCR TMDR TMCR Port Status Register Port Control Register Test Mode Data Register Test Mode Control Register 1 1 1 1 0 0 0 0 01000 01001 01010 01011 CMCR HCR IVR IOCR Clock Mode Control Register Hardware Configuration Register Interrupt Vector Register I/O Control Register 1 1 1 1 0 0 0 0 01100 01101 01110 01111 ICR DCCR MISR SICR Interrupt Control Register Daisy-Chain Control Register Misc. Interrupt Status Register Status Interrupt Control Register 1 1 1 1 1 0 0 0 XXXXX 1X000 10001 10010 RDR RDR RMR RCSR Receive Data Register (Read Only) Receive Data Register (Read Only) Receive Mode Register Receive Command/Status Register 1 1 1 1 0 0 0 0 10011 10100 10101 10110 RICR RSR RCLR RCCR Receive Interrupt Control Register Receive Sync Register Receive Count Limit Register Receive Character Count Register 1 1 1 1 1 0 1 0 0 0 10111 XXXXX 1X000 11001 11010 TC0R TDR TDR TMR TCSR Time Constant 0 Register Transmit Data Register (Write Only) Transmit Data Register (Write Only) Transmit Mode Register Transmit Command/Status Register 1 1 1 1 1 0 0 0 0 0 11011 11100 11101 11110 11111 TICR TSR TCLR TCCR TC1R Transmit Interrupt Control Register Transmit Sync Register Transmit Count Limit Register Transmit Character Count Register Time Constant 1 Register 21 PS97USC0200 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM Table 1. Register Address List (Continued) S//D D//C Address A5-A1 Name X 0 0 0 0 0 X 0 X X XXXXX 00000 00001 00011 00100 BCR DCAR TDCMR DCR DACR 0 0 0 0 0 X X X X X 01001 01010 01100 01101 01110 BDCR DIVR DICR CDIR SDIR Burst Dwell Control Register DMA Interrupt Vector Register DMA Interrupt Control Register Clear DMA Interrupt Register Set DMA Interrupt Register 0 0 0 0 0 0 0 0 0 0 01111 10101 10110 10111 11101 TDIAR TBCR TARL TARU NTBCR Transmit DMA Interrupt Arm Transmit Byte Count Register Transmit Address Register (Lower) Transmit Address Register (Upper) Next Transmit Byte Count Register 0 0 0 0 0 0 0 1 1 1 11110 11111 00001 01111 10101 NTARL NTARU RDMR RDIAR RBCR Next Transmit Address Register (Lower) Next Transmit Address Register (Upper) Receive DMA Mode Register Receive DMA Interrupt Arm Receive DMA Byte Count Register 0 0 0 0 0 1 1 1 1 1 10110 10111 11101 11110 11111 RARL RARU NRBCR NRARL NRARU Receive Address Register (Lower) Receive Address Register (Upper) Next Receive Byte Count Register Next Receive Address Register (Lower) Next Receive Address Register (Upper) PS97USC0200 Description Bus Configuration Register DMA Command/Address Register Transmit DMA Channel Mode Register DMA Control Register DMA Array Count Register 22 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM REGISTER DESCRIPTION This section describes the function of the various bits in the registers of the device. Throughout this section the following conventions are discussed: Control bits are written and read by the CPU and are not modified by the device. Command bits are written by the CPU to initiate an action in the device and are read as zeros. Status bits are controlled by the device and are read to check device status. Any writes to status bits are ignored by the device. Command/Status bits are controlled by both the device and the CPU. They may be written and read by the CPU and may also be modified by the device. Reserved bits are not used in this implementation of the device and may or may not be physically present in the device. Any reserved bits that are physically present are readable and writable, but reserved bits that are not present are always read as zeros. To ensure compatibility with future versions of the device, reserved bits should always be written with zeros. Reserved commands should not be used for the same reason. First, the DMA registers unique to the IUSC are described in the following pages (Figures 8-17) and then the serial channel registers are described (Figures 18-81). Address: 00000 (Shared) * D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 Upper//Lower Byte Select (WO) Address 0 (WO) Address 1 (WO) Address 2 (WO) Address 3 (WO) Address 4 (WO) Byte//Word Access (WO) Pointer Channel Select (WO) Master Bus Request Enable 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 Tx Channel Rx Channel Reserved Reserved Reserved Reserved Reserved Reserved Null Command Reset This Channel Start This Channel Start/Continue This Channel Pause This Channel Abort This Channel Reserved Start/Init This Channel Reset Highest IUS Reset All Channels Start All Channels Start/Continue All Channels Pause All Channels Abort All Channels Reserved Start/Init All Channels Channel Select (WO)** Channel Command Notes: * (Shared) means, shared between DMA Channels ** (WO) means Write Only Figure 8. DMA Command/Address Register 23 PS97USC0200 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM D7 D6 D5 D4 D3 D2 D1 D0 Software Abort (RO) Hardware Abort (RO) Buffer Termination (RO) Array Termination (RO) Busy (RO) Initializing (RO) Get Link (RO) Continue (RO) 0 X 1 X X X X X 0 X X X X X X X 0 X X X X X 1 X 0 1 1 1 0 0 1 1 0 0 X X X X X X X X X X X X X X 0 X X X X X X X 0 X X X X 1 X X Reset Start Start/Continue (Buffered Mode) Start/Continue (Other Than Buffered Mode) Pause Abort Start/Init (Array or Linked Array Modes) Start/Init (Normal or Buffered Modes) Command Notes: X = Previous Value (RO) = Read Only Figure 9. Affect of Commands on Status Bits PS97USC0200 24 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM CONTROL REGISTERS (Continued) Address: 00001 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 Software Abort (RO) Hardware Abort (RO) End of Buffer (RO) End of Array/Link (RO) Initialization (RO) Busy (RO) Get Link (RO) Continue (RO) 8-Bit Operand Enable Early Termination 0 0 1 1 0 1 0 1 Increment Decrement Fixed Address Reserved Address Mode Ring Buffer Enable Linked Frame Status Transfer 0 0 1 1 0 1 0 1 Auto Modes Disabled Buffered Array Chained Linked-Array Chained DMA Mode Figure 10. Tx/Rx DMA Mode Register (TDMR) (RDMR) 25 PS97USC0200 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM D7 D6 D5 D4 Initialization Busy Get Link Continue 0 0 X X 1 0 0 X 1 X 0 1 X X X 0 0 1 X X Channel Disabled Channel Enabled Not Possible Not Possible Not Possible 0 0 1 1 X X 0 0 0 0 X 1 0 1 0 1 X X 0 0 0 0 1 X Channel Disabled, Base Registers Invalid Channel Enabled, Base Registers Invalid Channel Disabled, Base Registers Valid Channel Enabled, Base Registers Valid Not Possible Not Possible Buffered Mode 0 0 0 0 X 1 0 0 0 0 1 X 0 1 0 1 X X 0 0 1 1 X X Channel Disabled, Data Transfer Phase Channel Enabled, Data Transfer Phase Channel Disabled, Array Transfer Phase Channel Enabled, Array Transfer Phase Not Possible Not Possible Array-Chained Mode 0 0 0 0 0 0 0 1 0 0 0 0 1 1 1 X 0 1 0 1 X 0 1 X 0 0 1 1 0 1 1 X Channel Disabled, Data Transfer Phase Channel Enabled, Data Transfer Phase Channel Disabled, Array Transfer Phase Channel Enabled, Array Transfer Phase Not Possible Channel Disabled, Link Transfer Phase Channel Enabled, Link Transfer Phase Not Possible Linked Array-Chained Mode Normal Mode Figure 11. Status Bit Combinations PS97USC0200 26 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM CONTROL REGISTERS (Continued) Address: 00011 (Shared) D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 0 0 1 1 0 1 0 1 32-bit Linear Reserved Segmented 16/16 Segmented 8/24 Addressing Mode /UAS Every Transaction One Wait Every Transaction Enable Transaction Status Bus Inactive Time Reserved Reserved Reserved Reserved 0 0 1 1 0 1 0 1 End of Demand or Burst End of Demand Only End of Burst Only Reserved DMA Request Arbitration Link Array Big End/Little End Preempt Enable 0 0 1 1 0 1 0 1 Tx Channel Rx Channel Alternating Reserved Channel Priority Figure 12. DMA Control Register (DCR) 27 PS97USC0200 P R E L I M I N A R Y ZILOG Big End Array (16-Bit bus) Z16C32 IUSCTM AD15 AD0 Address n 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 Address n+2 15 14 13 12 11 10 09 08 07 06 05 04 03 02 01 00 Little End Array (16-Bit bus) AD15 AD0 Address n 15 14 13 12 11 10 09 08 07 06 05 04 03 02 01 00 Address n+2 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 Big End Array (8-Bit bus) AD7 AD0 Address n 31 30 29 28 27 26 25 24 Address n+1 23 22 21 20 19 18 17 16 Address n+2 15 14 13 12 11 10 09 08 Address n+3 07 06 05 04 03 02 01 00 Little End Array (8-Bit bus) AD7 AD0 Address n 07 06 05 04 03 02 01 00 Address n+1 15 14 13 12 11 10 09 08 Address n+2 23 22 21 20 19 18 17 16 Address n+3 31 30 29 28 27 26 25 24 Figure 13. Array-Chained Bit Ordering Note: Bit 12 in DCR is used to control the byte ordering of addresses and counts stored in memory in the Array and Linked Array Modes. The above figure shows the two cases for both bus bandwidths. PS97USC0200 28 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM CONTROL REGISTERS (Continued) Address: 00100 (Shared) D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 Tx Channel Array Count (RO) Rx Channel Array Count (RO) Reserved Figure 14a. DMA Array Count Register (DACR) Getlink (in DCMR) Channel Array Count 3 Channel Array Count 2 Channel Array Count 1 Channel Array Count 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 Array Operation Not Started Fetched Last Byte of Array Fetched Fifth Byte of Array Fetched Fourth Byte of Array Fetched Third Byte of Array Fetched Second Byte of Array Fetched First Byte of Array Fetched Last Byte of Buffer 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 Array Operation Not Started Fetched Last Byte of Array Fetched Fifth Byte of Array Fetched Fourth Byte of Array Fetched Third Byte of Array Fetched Second Byte of Array Fetched First Byte of Array Fetched Last Byte of Linked Address Invalid Invalid Invalid Invalid Fetched Third Byte of Linked Address Fetched Second Byte of Linked Address Fetched First Byte of Linked Address Fetched Last Byte of Buffer Array-Chained Linked Array-Chained Figure 14b. Channel Array Count Bit Combinations Note: See the Z16C32 Technical Manual for the appropriate table with Linked Status Transfer feature enabled. 29 PS97USC0200 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM Address: 01001 (Shared) D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 Clock Cycle Limit (Bit 3) Clock Cycle Limit (Bit 4) Clock Cycle Limit (Bit 5) Clock Cycle Limit (Bit 6) Clock Cycle Limit (Bit 7) Clock Cycle Limit (Bit 8) Clock Cycle Limit (Bit 9) Clock Cycle Limit (Bit 10) Transaction Limit (Bit 0) Transaction Limit (Bit 1) Transaction Limit (Bit 2) Transaction Limit (Bit 3) Transaction Limit (Bit 4) Transaction Limit (Bit 5) Transaction Limit (Bit 6) Transaction Limit (Bit 7) Figure 15. Burst Dwell Control Register (BDCR) Notes: BDCR Controls the amount of time that DMA may remain bus master. Bits 15 through 8 are used to select a limit for the number of DMA transfers on the Bus while the DMA is bus master. This limit is a binary number, a value of zero disables the transaction limit function. Bits 7 through 0 are used to select a limit for the number of clock cycles that the DMA may remain on the bus as bus master. Bus transaction will always complete, even if the clock cycle limit is exceeded during the bus cycle, and even if the cycle is extended by external hardware signalling through /WAIT//RDY. PS97USC0200 30 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM CONTROL REGISTERS (Continued) Address: 01010 (Shared) D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 IV <0> IV <1> IV <2> IV <3> IV <4> IV <5> IV <6> IV <7> IV <0> (RO) 0 0 1 1 0 1 0 1 None Not Used Tx Channel Rx Channel Type Code (RO) IV <3> (RO) IV <4> (RO) IV <5> (RO) IV <6> (RO) IV <7> (RO) Figure 16. DMA Interrupt Vector Register (DIVR) Address: 01100 (Shared) D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 Tx IE Rx IE Reserved VIS NV DLC MIE Figure 17. DMA Interrupt Control Register (DICR) 31 PS97USC0200 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM Address: 01101 (Shared) D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 Reset Tx IP (WO) Reset Rx IP (WO) Reserved Reset Tx IUS (WO) Reset Rx IUS (WO) Reserved Figure 18. Clear DMA Interrupt Register (CDIR) Address: 01110 (Shared) D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 Set Tx IP Set Rx IP Reserved Set Tx IUS Set Rx IUS Reserved Figure 19. Set DMA Interrupt Register (SDIR) Address: 01111 * D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 Software Abort IA Hardware Abort IA Buffer Termination IA Array Termination IA Reserved Figure 20. Tx/Rx DMA Interrupt Arm (TDIAR)/(RDIAR) Notes: * The format of this register is the same for the receiver and transmitter. The transmit register is accessed by addressing it with the D//C pin Low (0). The receive register is accessed by addressing it with the D//C pin High (1). This applies to Figures 20 through 26. PS97USC0200 32 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM CONTROL REGISTERS (Continued) Address: 10101 * D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 TTC <0> TTC <1> TTC <2> TTC <3> TTC <4> TTC <5> TTC <6> TTC <7> TTC <8> TTC <9> TTC <10> TTC <11> TTC <12> TTC <13> TTC <14> TTC <15> Figure 21. Tx/Rx Byte Count Register (TBCR)/(RBCR) Address: 10110 * D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 TAR <0> TAR <1> TAR <2> TAR <3> TAR <4> TAR <5> TAR <6> TAR <7> TAR <8> TAR <9> TAR <10> TAR <11> TAR <12> TAR <13> TAR <14> TAR <15> Figure 22. Tx/Rx Address Register (lower) (TARL)/(RARL) 33 PS97USC0200 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM Address: 10111 * D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 TAR <16> TAR <17> TAR <18> TAR <19> TAR <20> TAR <21> TAR <22> TAR <23> TAR <24> TAR <25> TAR <26> TAR <27> TAR <28> TAR <29> TAR <30> TAR <31> Figure 23. Tx/Rx Address Register (Upper) (TARU)/(RARU) Address: 11101 * D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 BTC <0> BTC <1> BTC <2> BTC <3> BTC <4> BTC <5> BTC <6> BTC <7> BTC <8> BTC <9> BTC <10> BTC <11> BTC <12> BTC <13> BTC <14> BTC <15> Figure 24. Next Tx/Rx Byte Counter Register (NTBCR)/(RTBCR) PS97USC0200 34 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM CONTROL REGISTERS (Continued) Address: 11110 * D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 BAR <0> BAR <1> BAR <2> BAR <3> BAR <4> BAR <5> BAR <6> BAR <7> BAR <8> BAR <9> BAR <10> BAR <11> BAR <12> BAR <13> BAR <14> BAR <15> Figure 25. Next Tx/Rx Address Register (Lower) (NTARL)/(RTARL) Address: 11111 * D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 BAR <16> BAR <17> BAR <18> BAR <19> BAR <20> BAR <21> BAR <22> BAR <23> BAR <24> BAR <25> BAR <26> BAR <27> BAR <28> BAR <29> BAR <30> BAR <31> Figure 26. Next Tx/Rx Address Register (Upper) (NTARU)/(RTARU) 35 PS97USC0200 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM AD0 AD15 Base Address Buffer #1 Base Address + 2 Base Address + 4 Buffer #2 AD<31-24> AD<23-16> AD<15-8> AD<7-0> CNT<15-8> CNT<7-0> AD<31-24> AD<23-16> Base Address + 8 AD<15-8> AD<7-0> Base Address + 10 CNT<15-8> CNT<7-0> AD<31-24> AD<23-16> Base Address + 14 AD<15-8> AD<7-0> Base Address + 16 CNT<15-8> CNT<7-0> Ignored Ignored Last Base Address + 2 Ignored Ignored Last Base Address + 4 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Base Address + 6 Base Address + 12 Last Base Address Buffer #3 Dummy Base Address Register After Termination Figure 27a. Array-Chained, 16-Bit Bus, Big End Array Note: The addition of frame status/control information in the array with Linked Frame Status Transfer Enabled is similar for Big and Little End Array. See Figure 27b. PS97USC0200 36 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM CONTROL REGISTERS (Continued) AD0 AD15 Base Address Buffer #1 AD<31-24> AD<23-16> Base Address + 2 AD<15-8> AD<7-0> Base Address + 4 CNT <15-8> CNT <7-0> Base Address + 6 RSB/TCB <15-8> RSB/TCB <7-0> Base Address + 8 RCHR/TCLR <15-8> RCHR/TCLR <7-0> Base Address + 10 Base Address + 12 Buffer #2 0 0 AD<31-24> AD<23-16> Base Address + 14 AD<15-8> AD<7-0> Base Address + 16 CNT <15-8 > CNT <7-0> Base Address + 18 RSB/TCB <15-8> RSB/TCB <7-0> Base Address + 20 RCHR/TCLR <15-8> RCHR/TCLR <7-0> Base Address + 22 0 0 AD<31-24> AD<23-16> Base Address + 26 AD<15-8> AD<7-0> Base Address + 28 CNT <15-8> CNT <7-0> RSB/TCB <15-8> RSB/TCB <7-0> Base Address + 24 Buffer #3 Base Address + 30 RCHR/TCLR <15-8> RCHR/TCLR <7-0> Base Address + 32 Base Address + 34 Last Base Address Dummy 0 0 Ignored Ignored Last Base Address + 2 Ignored Ignored Last Base Address + 4 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Base Address Register After Termination Figure 27b. Array-Chained, 16-Bit Bus, Big End Array Linked Frame Status Transfer Enabled 37 PS97USC0200 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM AD0 AD15 Buffer #1 AD<15-8> AD<7-0> Base Address + 2 AD<31-24> AD<23-16> Base Address + 4 CNT<15-8> CNT<7-0> AD<15-8> AD<7-0> Base Address + 8 AD<31-24> AD<23-16> Base Address + 10 CNT<15-8> CNT<7-0> AD<15-8> AD<7-0> Base Address + 14 AD<31-24> AD<23-16> Base Address + 16 CNT<15-8> CNT<7-0> Ignored Ignored Last Base Address + 2 Ignored Ignored Last Base Address + 4 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Base Address Base Address + 6 Base Address + 12 Last Base Address Buffer #2 Buffer #3 Dummy Base Address Register After Termination Figure 28. Array-Chained, 16-Bit Bus, Little End Array PS97USC0200 38 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM CONTROL REGISTERS (Continued) AD0 AD7 Base Address Buffer #1 AD<31-24> Base Address + 1 AD<23-16> Base Address + 2 AD<15-8> Base Address + 3 AD<7-0> Base Address + 4 CNT<15-8> Base Address + 5 Base Address + 6 CNT<7-0> Buffer #2 AD<31-24> Base Address + 7 AD<23-16> Base Address + 8 AD<15-8> Base Address + 9 AD<7-0> Base Address + 10 CNT<15-8> Base Address + 11 CNT<7-0> Last Base Address Dummy Ignored Last Base Address + 1 Ignored Last Base Address + 2 Ignored Last Base Address + 3 Ignored Last Base Address + 4 0 0 0 0 0 0 0 0 Last Base Address + 5 0 0 0 0 0 0 0 0 Base Address Register After Termination Figure 29a. Array-Chained, 8-Bit Bus, Big End Array Note: The addition of frame status/control information in the array with Linked Frame Status Transfer Enabled is similar for Big and Little End Array. See Figure 29b. 39 PS97USC0200 ZILOG P R E L I M I N A R Y Z16C32 IUSCTM AD0 AD7 Base Address Buffer #1 AD<31-24> Base Address + 1 AD<23-16> Base Address + 2 AD<15-8> Base Address + 3 AD<7-0> Base Address + 4 CNT<15-8> Base Address + 5 CNT<7-0> Base Address + 6 RSB/TCB <15-8> Base Address + 7 RSB/TCB <7-0> Base Address + 8 RCHR/TCLR <15-8> Base Address + 9 RSHR/TCLR <7-0> Base Address + 10 0 Base Address + 11 0 Base Address + 12 Buffer #2 AD<31-24> Base Address + 13 AD<23-16> Base Address + 14 AD<15-8> Base Address + 15 AD<7-0> Base Address + 16 CNT<15-8> Base Address + 17 CNT<7-0> Base Address + 18 RSB/TCB <15-8> Base Address + 19 RSB/TCB <7-0> Base Address + 20 RCHR/TCLR <15-8> Base Address + 21 RSHR/TCLR <7-0> Base Address + 22 0 Base Address + 23 0 Last Base Address Dummy Ignored Last Base Address + 1 Ignored Last Base Address + 2 Ignored Last Base Address + 3 Ignored Last Base Address + 4 0 0 0 0 0 0 0 0 Last Base Address + 5 0 0 0 0 0 0 0 0 Base Address Register After Termination Figure 29b. Array-Chained, 8-Bit Bus, Big End Array, Linked Frame Status Transfer Enabled PS97USC0200 40 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM CONTROL REGISTERS (Continued) AD0 AD7 Base Address Buffer #1 AD<7-0> Base Address + 1 AD<15-8> Base Address + 2 AD<23-16> Base Address + 3 AD<31-24> Base Address + 4 CNT<7-0> CNT<15-8> Base Address + 5 Base Address + 6 Buffer #2 AD<7-0> Base Address + 7 AD<15-8> Base Address + 8 AD<23-16> Base Address + 9 AD<31-24> Base Address + 10 CNT<7-0> Base Address + 11 CNT<15-8> Last Base Address Dummy Ignored Last Base Address + 1 Ignored Last Base Address + 2 Ignored Last Base Address + 3 Ignored Last Base Address + 4 0 0 0 0 0 0 0 0 Last Base Address + 5 0 0 0 0 0 0 0 0 Base Address Register After Termination Figure 30. Array-Chained, 8-Bit Bus, Little End Array 41 PS97USC0200 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM AD15 Base Address Buffer #1 AD0 AD<31-24> AD<23-16> Base Address + 2 AD<15-8> AD<7-0> Base Address + 4 CNT<15-8> CNT<7-0> AD<31-24> AD<23-16> AD<15-8> AD<7-0> AD<31-24> AD<23-16> Base Address + 6 Base #2 Base Address + 8 #2 Base Address Buffer #2 #2 Base Address + 2 AD<15-8> AD<7-0> #2 Base Address + 4 CNT<15-8> CNT<7-0> AD<31-24> AD<23-16> AD<15-8> AD<7-0> #2 Base Address + 6 Base #3 #2 Base Address + 8 AD<31-24> AD<23-16> #3 Base Address + 2 AD<15-8> AD<7-0> #3 Base Address + 4 CNT<15-8> CNT<7-0> #3 Base Address #n - 1 Base Address + 6 Buffer #3 Base #n AD<31-24> AD<23-16> AD<15-8> AD<7-0> Ignored Ignored #n Base Address + 2 Ignored Ignored #n Base Address + 4 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 #n - 1 Base Address + 8 #n Base Address Buffer #n Figure 31a. Linked Array-Chained, 16-Bit Bus, Big End Array Note: The addition of frame status/control information in the array with Linked Frame Status Transfer Enabled is similar for Big and Little End Array. See Figure 31b. PS97USC0200 42 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM CONTROL REGISTERS (Continued) AD0 AD15 Base Address Buffer #1 Base Address + 2 AD<31-24> AD<23-16> AD <15-8> AD<7-0> Base Address + 4 CNT<15-8> CNT<7-0> Base Address + 6 RSB/TCB <15-8> RSB/TCB <7-0> RCHR/TCLR <15-8> RCHR/TCLR <7-0> Base Address + 8 0 0 Base #2 AD<31-24> AD<23-16> AD <15-8> AD<7-0> Buffer #2 AD<31-24> AD<23-16> #2 Base Address + 2 AD <15-8> AD<7-0> #2 Base Address + 4 CNT<15-8> CNT<7-0> #2 Base Address + 6 RSB/TCB <15-8> RSB/TCB <7-0> Base Address + 10 Base Address + 12 Base Address + 14 #2 Base Address RCHR/TCLR <15-8> RCHR/TCLR <7-0> #2 Base Address + 8 #2 Base Address + 10 #2 Base Address + 12 Base #3 #2 Base Address + 14 #3 Base Address Buffer #3 0 0 AD<31-24> AD<23-16> AD <15-8> AD<7-0> AD<31-24> AD<23-16> #3 Base Address + 2 AD <15-8> AD<7-0> #3 Base Address + 4 CNT<15-8> CNT<7-0> #3 Base Address + 6 RSB/TCB <15-8> RSB/TCB <7-0> #3 Base Address + 8 #3 Base Address + 10 RCHR/TCLR <15-8> RCHR/TCLR <7-0> 0 0 Figure 31b. Linked Array-Chained, 16-Bit Bus, Big End Array 43 PS97USC0200 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM AD15 AD0 AD<15-8> AD<7-0> Base Address + 2 AD<31-24> AD<23-16> Base Address + 4 CNT<15-8> CNT<7-0> AD<15-8> AD<7-0> AD<31-24> AD<23-16> AD<15-8> AD<7-0> #2 Base Address + 2 AD<31-24> AD<23-16> #2 Base Address + 4 CNT<15-8> CNT<7-0> AD<15-8> AD<7-0> AD<31-24> AD<23-16> AD<15-8> AD<7-0> #3 Base Address + 2 AD<31-24> AD<23-16> #3 Base Address + 4 CNT<15-8> CNT<7-0> Base Address Base Address + 6 Buffer #1 Base #2 Base Address + 8 #2 Base Address #2 Base Address + 6 Buffer #2 Base #3 #2 Base Address + 8 #3 Base Address #n - 1 Base Address + 6 Buffer #3 Base #n #n - 1 Base Address + 8 AD<15-8> AD<7-0> AD<31-24> AD<23-16> Ignored Ignored #n Base Address + 2 Ignored Ignored #n Base Address + 4 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 #n Base Address Buffer #n Figure 32. Linked Array-Chained, 16-Bit Bus, Little End Array PS97USC0200 44 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM CONTROL REGISTERS (Continued) AD7 Base Address Buffer #1 AD0 AD<7-0> Base Address + 1 AD<15-8> Base Address + 2 AD<23-16> Base Address + 3 AD<31-24> Base Address + 4 CNT<7-0> Base Address + 5 CNT<15-8> Base Address + 6 Base #2 AD<7-0> Base Address + 7 AD<15-8> Base Address + 8 AD<23-16> Base Address + 9 AD<31-24> #2 Base Address Buffer #2 AD<7-0> #2 Base Address + 1 AD<15-8> #2 Base Address + 2 AD<23-16> #2 Base Address + 3 AD<31-24> #2 Base Address + 4 CNT<7-0> #2 Base Address + 5 CNT<15-8> #2 Base Address + 6 Base #3 AD<7-0> #2 Base Address + 7 AD<15-8> #2 Base Address + 8 AD<23-16> #2 Base Address + 9 AD<31-24> Figure 33a. Linked Array-Chained, 8-Bit Bus, Big End Array Note: The addition of frame status/control information in the array with Linked Frame Status Transfer Enabled is similar to Big End Array. See Figure 33b. 45 PS97USC0200 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM AD0 AD7 Base Address Buffer #1 AD<31-24> Base Address + 1 AD<23-16> Base Address + 2 AD<15-8> Base Address + 3 AD<7-0> Base Address + 4 CNT<15-8> Base Address + 5 CNT<7-0> Base Address + 6 RSB/TCB <15-8> Base Address + 7 RSB/TCB <7-0> Base Address + 8 RCHR/TCLR <15-8> Base Address + 9 RCHR/TCLR <7-0> Base Address + 10 0 Base Address + 11 0 Base Address + 12 Base #2 AD<31-24> Base Address + 13 AD<23-16> Base Address + 14 AD<15-8> Base Address + 15 AD<7-0> #2 Base Address Buffer #2 AD<31-24> #2 Base Address + 1 AD<23-16> #2 Base Address + 2 AD<15-8> #2 Base Address + 3 AD<7-0> #2 Base Address + 4 CNT<15-8> #2 Base Address + 5 CNT<7-0> #2 Base Address + 6 RSB/TCB <15-8> #2 Base Address + 7 RSB/TCB <7-0> #2 Base Address + 8 RCHR/TCLR <15-8> #2 Base Address + 9 RCHR/TCLR <7-0> #2 Base Address + 10 0 #2 Base Address + 11 0 Figure 33b. Linked Frame Status Transfer Enables PS97USC0200 46 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM CONTROL REGISTERS (Continued) AD7 Base Address Buffer #1 AD0 AD<31-24> Base Address + 1 AD<23-16> Base Address + 2 AD<15-8> Base Address + 3 AD<7-0> Base Address + 4 CNT<15-8> Base Address + 5 CNT<7-0> Base Address + 6 Base #2 AD<31-24> Base Address + 7 AD<23-16> Base Address + 8 AD<15-8> Base Address + 9 AD<7-0> #2 Base Address Buffer #2 AD<31-24> #2 Base Address + 1 AD<23-16> #2 Base Address + 2 AD<15-8> #2 Base Address + 3 AD<7-0> #2 Base Address + 4 CNT<15-8> #2 Base Address + 5 CNT<7-0> #2 Base Address + 6 Base #3 AD<31-24> #2 Base Address + 7 AD<23-16> #2 Base Address + 8 AD<15-8> #2 Base Address + 9 AD<7-0> Figure 34. Linked Array-Chained 8-Bit Bus, Little End Array 47 PS97USC0200 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM Address: 00000 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 Upper//Lower Byte Select (WO) Address 0 (WO) Address 1 (WO) Address 2 (WO) Address 3 (WO) Address 4 (WO) Byte//Word Access (WO) Channel Load DMA (WO) 0 0 1 1 0 1 0 1 Normal Operation Auto Echo External Local Loopback Internal Local Loopback Rx/Tx Mode Rx/Tx Reset 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 Null Command Reserved Reset Highest IUS Reserved Trigger Channel Load DMA Trigger Rx DMA Trigger Tx DMA Trigger Rx & Tx DMA Reserved Rx FIFO Purge Tx FIFO Purge Rx & Tx FIFO Purge Reserved Load Rx Character Count Load Tx Character Count Load Rx & Tx Character Count Reserved Load TC0 Load TC1 Load TC0 & TC1 Select Serial Data LSB First * Select Serial Data MSB First Select Straight Memory Data * Select Swapped Memory Data Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Channel Command (WO) * Selected Upon Reset Figure 35. Channel Command/Address Register (CCAR) PS97USC0200 48 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM CONTROL REGISTERS (Continued) Address: 00001 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 Asynchronous External Synchronous Isochronous Asynchronous with CV Monosync Bisync HDLC Transparent Bisync NBIP 802.3 Reserved Reserved Reserved Reserved Reserved Reserved Receiver Mode Rx Submode 0 Rx Submode 1 Rx Submode 2 Rx Submode 3 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 Asynchronous Reserved Isochronous Asynchronous with CV Monosync Bisync HDLC Transparent Bisync NBIP 802.3 Reserved Reserved Slaved Monosync Reserved HDLC Loop Reserved Transmitter Mode Tx Submode 0 Tx Submode 1 Tx Submode 2 Tx Submode 3 Figure 36. Channel Mode Register (CMR) 49 PS97USC0200 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM Address: 00001 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 0 0 1 1 0 1 0 1 D3 D2 D1 D0 0 0 0 0 16X Data Rate 32X Data Rate 64X Data Rate Reserved Asynchronous Receiver Mode Rx Clock Rate Reserved Reserved 0 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 0 0 16X Data Rate 32X Data Rate 64X Data Rate Reserved One Stop Bit Two Stop Bits One Stop Bit, Shaved Two Stop Bits, Shaved Transmitter Mode Asynchronous Tx Clock Rate Tx Stop Bits Figure 37. Channel Mode Register, Asynchronous Mode Address: 00001 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 0 0 0 1 External Sync Receiver Mode Reserved 0 0 0 1 Reserved Transmitter Mode Reserved Figure 38. Channel Mode Register, External Sync Mode PS97USC0200 50 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM CONTROL REGISTERS (Continued) Address: 00001 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 0 0 1 0 Isochronous Receiver Mode Reserved 0 0 1 0 Isochronous Transmitter Mode Reserved Tx Two Stop Bits Reserved Figure 39. Channel Mode Register, Isochronous Mode Address: 00001 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 0 0 1 1 Receiver Mode Asynchronous with CV Rx Extended Word Reserved 0 0 1 1 Asynchronous with CV Transmitter Mode CV Polarity Tx Extended Word 0 0 1 1 0 1 0 1 One Stop Bit Two Stop Bits No Stop Bit Reserved Tx Stop Bits Figure 40. Channel Mode Register, Asynchronous Mode with Code Violation (MIL STD 1553) 51 PS97USC0200 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM Address: 00001 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 0 1 0 0 Monosync Receiver Mode Rx Short Sync Character Rx Sync Strip Reserved 0 1 0 0 Transmitter Mode Monosync Tx Short Sync Character Tx Preamble Enable Reserved Tx CRC on Underrun Figure 41. Channel Mode Register, Monosync Mode Address: 00001 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 0 1 0 1 Bisync Receiver Mode Rx Short Sync Character Rx Sync Strip Reserved 0 1 0 1 Bisync Transmitter Mode Tx Short Sync Character Tx Preamble Enable 0 0 1 1 0 1 0 1 SYN1 SYN0/SYN1 CRC/SYN1 CRC/SYN0/SYN1 Tx Underrun Condition Figure 42. Channel Mode Register, Bisync Mode PS97USC0200 52 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM CONTROL REGISTERS (Continued) Address: 00001 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 0 0 1 1 D4 0 1 0 1 D3 D2 D1 D0 0 1 1 0 HDLC Disabled One Byte, No Control One Byte, Plus Control Extended, Plus Control Receiver Mode Rx Address Search Mode Rx 16-Bit Control Rx Logical Control Enable 0 1 1 0 HDLC Transmitter Mode Shared Zero Flags Tx Preamble Enable 0 0 1 1 0 1 0 1 Abort Extended Abort Flag CRC/Flag Tx Underrun Condition Figure 43. Channel Mode Register, HDLC Mode Address: 00001 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 0 1 1 1 Transparent Bisync Receiver Mode EBCDIC Reserved 0 1 1 1 Transparent Bisync Transmitter Mode EBCDIC Tx Preamble Enable 0 0 1 1 0 1 0 1 SYN DLE/SYN CRC/SYN CRC/DLE/SYN Tx Underrun Condition Figure 44. Channel Mode Register, Transparent Bisync Mode 53 PS97USC0200 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM Address: 00001 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 0 0 1 1 D4 0 1 0 1 D3 D2 D1 D0 1 0 0 0 16X Data Rate 32X Data Rate 64X Data Rate Reserved Receiver Mode NBIP Rx Clock Rate Rx Parity on Data Reserved 1 0 0 1 1 0 1 0 1 0 0 0 Transmitter Mode NBIP 16X Data Rate 32X Data Rate 64X Data Rate Reserved Tx Clock Rate Tx Parity on Data Tx Address Bit Figure 45. Channel Mode Register, NBIP Mode Address: 00001 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 1 0 0 1 802.3 Receiver Mode Rx Address Search Reserved 1 0 0 1 802.3 Transmitter Mode Reserved Tx CRC on Underrun Figure 46. Channel Mode Register, 802.3 Mode PS97USC0200 54 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM CONTROL REGISTERS (Continued) Address: 00001 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 1 1 D1 D0 0 0 Reserved Receiver Mode Reserved 1 1 0 0 Slaved Monosync Transmitter Mode Tx Short Sync Character Tx Active on Received Sync Reserved Tx CRC on Underrun Figure 47. Channel Mode Register, Slaved Monosync Mode Address: 00001 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 1 1 1 0 Reserved Receiver Mode Reserved 1 1 1 0 HDLC Loop Transmitter Mode Shared-Zero Flags Tx Active on Poll 0 0 1 1 0 1 0 1 Abort Extended Abort Flag CRC/Flag Tx Underrun Condition Figure 48. Channel Mode Register, HDLC Loop Mode 55 PS97USC0200 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM Address: 00010 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 Reserved 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 8 Bits 1 Bit 2 Bits 3 Bits 4 Bits 5 Bits 6 Bits 7 Bits HDLC Tx Last Character Length Counter By-pass Enable Loop Sending (RO) On Loop (RO) 0 0 1 1 0 1 0 1 Both Edges Rising Edge Only Falling Edge Only Adjust/Sync Inhibit DPLL Adjust/Sync Edge Clock Missed Latched/Unlatch 2 Clocks Missed Latched/Unlatch DPLL in Sync/Quick Sync RCC FIFO Clear (WO) RCC FIFO Valid (RO) RCC FIFO Overflow (RO) Figure 49. Channel Command/Status Register (CCSR) PS97USC0200 56 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM CONTROL REGISTERS (Continued) Address: 00011 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 Reserved Wait for Rx DMA Trigger 0 0 1 1 0 1 0 1 No Status Block One Word Status Block Two Word Status Block Reserved Rx Status Block Transfer Tx Shaved Bit Length (Async Only) 0 0 1 1 0 1 0 1 All Zeros All Ones Alternating 1 and 0 Alternating 0 and 1 Tx Preamble Pattern (All Sync) 0 0 1 1 0 1 0 1 8 Bits 16 Bits 32 Bits 64 Bits Tx Preamble Length Tx Flag Preamble Wait for Tx DMA Trigger 0 0 1 1 0 1 0 1 No Status Block One Word Status Block Two Word Status Block Reserved Tx Control Block Transfer Figure 50. Channel Control Register (CCR) 57 PS97USC0200 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM Address: 00100 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 /Port Bit 0 (RO) Port Bit 0 Latched/Unlatch /Port Bit 1 (RO) Port Bit 1 Latched/Unlatch /Port Bit 2 (RO) Port Bit 2 Latched/Unlatch /Port Bit 3 (RO) Port Bit 3 Latched/Unlatch /Port Bit 4 (RO) Port Bit 4 Latched/Unlatch /Port Bit 5 (RO) Port Bit 5 Latched/Unlatch /Port Bit 6 (RO) Port Bit 6 Latched/Unlatch /Port Bit 7 (RO) Port Bit 7 Latched/Unlatch Figure 51. Port Status Register (PSR) PS97USC0200 58 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM CONTROL REGISTERS (Continued) Address: 00101 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 Tri-State Output Tx Complete Output Output 0 Output 1 0 1 0 1 D1 D0 0 0 1 1 0 1 0 1 Tri-State Output CLK0 Input Output 0 Output 1 Tri-State Output CLK1 Input Output 0 Output 1 Tri-State Output Reserved Output 0 Output 1 Tri-State Output Rx TSA Gate Output Output 0 Output 1 Tri-State Output Tx TSA Gate Output Output 0 Output 1 Tri-State Output Rx Sync Output Output 0 Output 1 Tri-State Output Frame Sync Input Output 0 Output 1 0 1 0 1 D2 Port Bit 0 Pin Control Port Bit 1 Pin Control Port Bit 2 Pin Control Port Bit 3 Pin Control Port Bit 4 Pin Control Port Bit 5 Pin Control Port Bit 6 Pin Control Port Bit 7 Pin Control Figure 52. Port Control Register (PCR) 59 PS97USC0200 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM Address: 00110 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 Test Data <0> Test Data <1> Test Data <2> Test Data <3> Test Data <4> Test Data <5> Test Data <6> Test Data <7> Test Data <8> Test Data <9> Test Data <10> Test Data <11> Test Data <12> Test Data <13> Test Data <14> Test Data <15> Figure 53. Test Mode Data Register (TMDR) PS97USC0200 60 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM CONTROL REGISTERS (Continued) Address: 00111 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 Null Address High Byte of Shifters CRC Byte 0 CRC Byte 1 Rx FIFO (Write) Clock Multiplexer Outputs CTR0 and CTR1 Counters Clock Multiplexer Inputs DPLL State Low Byte of Shifters CRC Byte 2 CRC Byte 3 Tx FIFO (Read) Reserved I/O and Device Status Latches Internal Daisy Chain Reserved Reserved Reserved Reserved Reserved Reserved Rx Count Holding Register Reserved Reserved Reserved Reserved 4453H Reserved Reserved Reserved 4453H Test Register Address Reserved Figure 54. Test Mode Control Register (TMCR) Note: When software writes the value 1F to the LS byte of the Test Mode Control Register (TMCR), and then reads the Test Mode Data Register (TMDR), current versions of the Z16C32 will return hex 4453. Future revisions, if any, will return other values. 61 PS97USC0200 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM Address: 01000 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 Disabled Port1 Pin /RxC Pin /TxC Pin 0 1 0 1 Disabled Port0 Pin /RxC Pin /TxC Pin 0 1 0 1 0 1 0 1 0 0 1 1 0 0 1 1 D3 0 1 0 1 0 1 0 1 BRG0 Output BRG1 Output /RxC Pin /TxC Pin CTR0 Output CTR1 Output /RxC Pin /TxC Pin CTR0 Output CTR1 Output /RxC Pin /TxC Pin D4 D2 D1 D0 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 Disabled /RxC Pin /TxC Pin DPLL Output BRG0 Output BRG1 Output CTR0 Output CTR1 Output Disabled /RxC Pin /TxC Pin DPLL Output BRG0 Output BRG1 Output CTR0 Output CTR1 Output Receive Clock Source Transmit Clock Source DPLL Clock Source BRG0 Clock Source BRG1 Clock Source CTR0 Clock Source CTR1 Clock Source Figure 55. Clock Mode Control Register (CMCR) PS97USC0200 62 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM CONTROL REGISTERS (Continued) Address: 01001 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 BRG0 Enable BRG0 Single Cycle/Continuous Reserved BRG1 Enable BRG1 Single Cycle/Continuous Reserved 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 Disabled NRZ/NRZI Biphase-Mark/Space Biphase-Level 32x Clock Mode 16x Clock Mode 8x Clock Mode Reserved DPLL Divider DPLL Clock Divider Code Violations OK CTR1 Rate Match DPLL/CTR0 0 0 1 1 0 1 0 1 32x Clock Mode 16x Clock Mode 8x Clock Mode 4x Clock Mode CTR0 Clock Divider Figure 56. Hardware Configuration Register (HCR) 63 PS97USC0200 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM Address: 01010 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 IV <0> IV <1> IV <2> IV <3> IV <4> IV <5> IV <6> IV <7> IV <0> (RO) 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 None Device Status I/O Status Transmit Data Transmit Status Receive Data Receive Status Not Used Type Code IV <4> (RO) IV <5> (RO) IV <6> (RO) IV <7> (RO) Figure 57. Interrupt Vector Register (IVR) PS97USC0200 64 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM CONTROL REGISTERS (Continued) Address: 01011 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 0 1 1 0 0 1 1 D3 0 1 0 1 0 1 0 1 D2 D1 D0 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 3-State Output Rx Request Output Output 0 Output 1 Input Pin Rx Clock Output Rx Byte Clock Output SYNC Output BRG0 Output BRG1 Output CTR0 Output DPLL Rx Output Input PIn Tx Clock Output Tx Byte Clock Output Tx Complete Output BRG0 Output BRG1 Output CTR1 Output DPLL Tx Output Tx Data Output 3-State Output Output 0 Output 1 3-State Output Tx Request Output Output 0 Output 1 /DCD Input /DCD//SYNC Input Output 0 Output 1 /CTS Input /CTS Input Output 0 Output 1 0 1 0 1 D4 /RxC Pin Control /TxC Pin Control TxD Pin Control /RxREQ Pin Control /TxREQ Pin Control /DCD Pin Control /CTS Pin Control Figure 58. I/O Control Register (IOCR) 65 PS97USC0200 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM Address: 01100 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 Device Status IE I/O Status IE Transmit Data IE Transmit Status IE Receive Data IE Receive Status IE 0 0 1 1 0 1 0 1 Null Command Null Command Reset IE Set IE IE Command (WO) Reserved 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 All All I/O Status and Above Transmit Data and Above Transmit Status and Above Receive Data and Above Receive Status Only None VIS Level VIS NV DLC MIE Figure 59. Interrupt Control Register (ICR) PS97USC0200 66 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM CONTROL REGISTERS (Continued) Address: 01101 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 Device Status IP I/O Status IP Transmit Data IP Transmit Status IP Receive Data IP Receive Status IP 0 0 1 1 0 1 0 1 Null Command Reset IP and IUS Reset IP Set IP IP Command (WO) Device Status IUS I/O Status IUS Transmit Data IUS Transmit Status IUS Receive Data IUS Receive Status IUS 0 0 1 1 0 1 0 1 Null Command Null Command Reset IUS Set IUS IUS Command (WO) Figure 60. Daisy-Chain Control Register (DCCR) 67 PS97USC0200 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM Address: 01110 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 BRG0 ZC Latched/Unlatch BRG1 ZC Latched/Unlatch DPLL SYNC Latched/Unlatch RCC Overflow Latched/Unlatch /CTS (RO) /CTS Latched/Unlatch /DCD (RO) /DCD Latched/Unlatch /TxREQ (RO) /TxREQ Latched/Unlatch /RxREQ (RO) /RxREQ Latched/Unlatch /TxC (RO) /TxC Latched/Unlatch /RxC (RO) /RxC Latched/Unlatch Figure 61. Miscellaneous Interrupt Status Register (MISR) PS97USC0200 68 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM CONTROL REGISTERS (Continued) Address: 01111 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 BRG0 ZC IA BRG1 ZC IA DPLL SYNC IA RCC Overflow IA 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 Disabled Rising Edge Only Falling Edge Only Both Edges Disabled Rising Edge Only Falling Edge Only Both Edges Disabled Rising Edge Only Falling Edge Only Both Edges Disabled Rising Edge Only Falling Edge Only Both Edges Disabled Rising Edge Only Falling Edge Only Both Edges Disabled Rising Edge Only Falling Edge Only Both Edges 0 1 0 1 0 1 0 1 /CTS Interrupt Arm /DCD Interrupt Arm /TxREQ Interrupt Arm /RxREQ Interrupt Arm /TxC Interrupt Arm /RxC Interrupt Arm Figure 62. Status Interrupt Control Register (SICR) 69 PS97USC0200 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM Address: 1x000 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 RxDAT <0> (RO) RxDAT <1> (RO) RxDAT <2> (RO) RxDAT <3> (RO) RxDAT <4> (RO) RxDAT <5> (RO) RxDAT <6> (RO) RxDAT <7> (RO) RxDAT <8> (RO) RxDAT <9> (RO) RxDAT <10> (RO) RxDAT <11> (RO) RxDAT <12> (RO) RxDAT <13> (RO) RxDAT <14> (RO) RxDAT <15> (RO) Figure 63. Receive Data Register (RDR) PS97USC0200 70 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM CONTROL REGISTERS (Continued) Address: 10001 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 0 0 0 0 1 1 1 1 D3 0 0 1 1 0 0 1 1 D2 0 1 0 1 0 1 0 1 D1 D0 0 0 1 1 0 1 0 1 8 Bits 1 Bit 2 Bits 3 Bits 4 Bits 5 Bits 6 Bits 7 Bits Disable Immediately Disable After Reception Enable Without Auto-Enables Enable With Auto-Enables Rx Enable Rx Character Length Rx Parity Enable 0 0 1 1 0 1 0 1 Even Odd Space Mark Rx Parity Type Abort Frame Status Rx CRC Enable Rx CRC Preset Value 0 0 1 1 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 CRC-CCITT CRC-16 CRC-32 Reserved NRZ NRZB NRZI-Mark NRZI-Space Biphase-Mark Biphase-Space Biphase-Level Diff. Biphase-Level Rx CRC Polynomial Rx Data Decoding Figure 64. Receive Mode Register (RMR) 71 PS97USC0200 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM Address: 10010 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 Rx Character Available (RO) Rx Overrun Parity Error/Rx Frame Abort CRC/Framing Error (RO) Rx CV/EOT/EOF Rx Break/Abort Rx Idle Exited Hunt Short Frame/CV Polarity (RO) Residue Code 0 (RO) Residue Code 1 (RO) Residue Code 2 (RO) 0 0 0 0 0 0 0 0 1 1 1 0 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 1 Null Command Reserved Preset CRC Enter Hunt Mode Select Timeslot Assignment Select FIFO Status Select FIFO Interrupt Level Select FIFO Request Level Reserved Reserved Reserved Reserved Reserved Reserved Reserved Receive Command (WO) First Byte in Error (RO) Second Byte in Error (RO) Figure 65. Receive Command Status Register (RCSR) PS97USC0200 72 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM CONTROL REGISTERS (Continued) Address: 10011 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 TC0R Read Count/TC Rx Overrun IA Parity Error/Frame Abort IA Status on Words Rx CV/EOT/EOF IA Rx Break/Abort IA Rx Idle IA Exited Hunt IA Rx FIFO Control and Status (Fill/Interrupt/DMA Level) Figure 66a. Receive Interrupt Control Register (RICR) Address: 10011 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 TC0R Read Count/TC Rx Overrun IA Parity Error/Frame Abort IA Status on Words Rx CV/EOT/EOF IA Rx Break/Abort IA Rx Idle IA Exited Hunt IA 0 Timeslot (0-127) Figure 66b. Receive Interrupt Control Register (RICR) 73 PS97USC0200 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM Address: 10011 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 TC0R Read Count/TC Rx Overrun IA Parity Error/Frame Abort IA Status on Words Rx CV/EOT/EOF IA Rx Break/Abort IA Rx Idle IA Exited Hunt IA 1 (WO) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 No Offset 7 Clocks Offset 6 Clocks Offset 5 Clocks Offset 4 Clocks Offset 3 Clocks Offset 2 Clocks Offset 1 Clock Offset No Slot (Disabled) 1 Slot 2 Slots 3 Slots 4 Slots 5 Slots 6 Slots 7 Slots 8 Slots 9 Slots 10 Slots 11 Slots 12 Slots 13 Slots 14 Slots 15 Slots Concatenated Slots (WO) Slot Offset (WO) Figure 66c. Receive Interrupt Control Register (RICR) PS97USC0200 74 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM CONTROL REGISTERS (Continued) Address: 10100 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 RSYN <0> RSYN <1> RSYN <2> RSYN <3> RSYN <4> RSYN <5> RSYN <6> RSYN <7> RSYN <8> RSYN <9> RSYN <10> RSYN <11> RSYN <12> RSYN <13> RSYN <14> RSYN <15> Figure 67. Receive Sync Register (RSR) 75 PS97USC0200 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM Address: 10101 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 RCL <0> RCL <1> RCL <2> RCL <3> RCL <4> RCL <5> RCL <6> RCL <7> RCL <8> RCL <9> RCL <10> RCL <11> RCL <12> RCL <13> RCL <14> RCL <15> Figure 68. Receive Count Limit Register (RCLR) PS97USC0200 76 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM CONTROL REGISTERS (Continued) Address: 10110 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 RCC <0> (RO) RCC <1> (RO) RCC <2> (RO) RCC <3> (RO) RCC <4> (RO) RCC <5> (RO) RCC <6> (RO) RCC <7> (RO) RCC <8> (RO) RCC <9> (RO) RCC <10> (RO) RCC <11> (RO) RCC <12> (RO) RCC <13> (RO) RCC <14> (RO) RCC <15> (RO) Figure 69. Receive Character Count Register (RCCR) 77 PS97USC0200 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM Address: 10111 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 TC0 <0> TC0 <1> TC0 <2> TC0 <3> TC0 <4> TC0 <5> TC0 <6> TC0 <7> TC0 <8> TC0 <9> TC0 <10> TC0 <11> TC0 <12> TC0 <13> TC0 <14> TC0 <15> Figure 70. Time Constant 0 Register (TC0R) PS97USC0200 78 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM CONTROL REGISTERS (Continued) Address: 1x000 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 TxDAT <0> (WO) TxDAT <1> (WO) TxDAT <2> (WO) TxDAT <3> (WO) TxDAT <4> (WO) TxDAT <5> (WO) TxDAT <6> (WO) TxDAT <7> (WO) TxDAT <8> (WO) TxDAT <9> (WO) TxDAT <10> (WO) TxDAT <11> (WO) TxDAT <12> (WO) TxDAT <13> (WO) TxDAT <14> (WO) TxDAT <15> (WO) Figure 71. Transmit Data Register (TDR) 79 PS97USC0200 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM Address: 11001 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 0 0 0 0 1 1 1 1 D3 0 0 1 1 0 0 1 1 D2 0 1 0 1 0 1 0 1 D1 D0 0 0 1 1 0 1 0 1 8 Bits 1 Bit 2 Bits 3 Bits 4 Bits 5 Bits 6 Bits 7 Bits Disable Immediately Disable After Transmission Enable Without Auto-Enables Enable With Auto-Enables Tx Enable Tx Character Length Tx Parity Enable 0 0 1 1 0 1 0 1 Even Odd Space Mark Tx Parity Sense Tx CRC on EOF/EOM Tx CRC Enable Tx CRC Start Value 0 0 1 1 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 CRC-CCITT CRC-16 CRC-32 Reserved NRZ NRZB NRZI-Mark NRZI-Space Biphase-Mark Biphase-Space Biphase-Level Diff. Biphase-Level Tx CRC Type Tx Data Encoding Figure 72. Transmit Mode Register (TMR) PS97USC0200 80 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM CONTROL REGISTERS (Continued) Address: 11010 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 Tx Buffer Empty (RO) Tx Underrun All Sent (RO) Tx CRC Sent Tx EOF/EOT Sent Tx Abort Sent Tx Idle Sent Tx Preamble Sent 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 SYNC/Flag/Normal Alternating 1 and 0 All Zeros All Ones Reserved Alternating Mark and Space Space Mark Tx Idle Line Condition Reserved 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 Null Command Reserved Preset CRC Reserved Select Timeslot Assignment Select FIFO Status Select Interrupt Level Select Request Level Send Frame/Message Send Abort Reserved Reserved Reset DLE Inhibit Set DLE Inhibit Reset EOF/EOM Set EOF/EOM Transmit Command (WO) Figure 73. Transmit Command/Status Register (TCSR) 81 PS97USC0200 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM Address: 11011 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 TC1R Read Count/TC Tx Overrun IA Wait for Send Command Tx CRC Sent IA Tx EOF/EOT Sent IA Tx Abort Sent IA Tx Idle Sent IA Tx Preamble Sent IA Tx FIFO Control and Status (Fill/Interrupt/DMA Level) Figure 74a. Transmit Interrupt Control Register (TICR) Address: 11011 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 TC1R Read Count/TC Tx Underrun IA Wait for Send Command Tx CRC Sent IA Tx EOF/EOT Sent IA Tx Abort Sent IA Tx Idle Sent IA Tx Preamble Sent IA 0 Timeslot (0-127) Figure 74b. Transmit Interrupt Control Register (TICR) PS97USC0200 82 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM CONTROL REGISTERS (Continued) Address: 11011 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 TC1R Read Count/TC Tx Underrun IA Wait for Send Command Tx CRC Sent IA Tx EOF/EOT Sent IA Tx Abort Sent IA Tx Idle Sent IA Tx Preamble Sent IA 1 (WO) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 No Offset 7 Clocks Offset 6 Clocks Offset 5 Clocks Offset 4 Clocks Offset 3 Clocks Offset 2 Clocks Offset 1 Clock Offset No Slot (Disabled) 1 Slot 2 Slots 3 Slots 4 Slots 5 Slots 6 Slots 7 Slots 8 Slots 9 Slots 10 Slots 11 Slots 12 Slots 13 Slots 14 Slots 15 Slots Concatenated Slots (WO) Slot Offset (WO) Figure 74c. Transmit Interrupt Control Register (TICR) 83 PS97USC0200 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM Address: 11100 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 TSYN <0> TSYN <1> TSYN <2> TSYN <3> TSYN <4> TSYN <5> TSYN <6> TSYN <7> TSYN <8> TSYN <9> TSYN <10> TSYN <11> TSYN <12> TSYN <13> TSYN <14> TSYN <15> Figure 75. Transmit Sync Register (TSR) PS97USC0200 84 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM CONTROL REGISTERS (Continued) Address: 11101 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 TCL <0> TCL <1> TCL <2> TCL <3> TCL <4> TCL <5> TCL <6> TCL <7> TCL <8> TCL <9> TCL <10> TCL <11> TCL <12> TCL <13> TCL <14> TCL <15> Figure 76. Transmit Count Limit Register (TCLR) 85 PS97USC0200 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM Address: 11110 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 TCC <0> (RO) TCC <1> (RO) TCC <2> (RO) TCC <3> (RO) TCC <4> (RO) TCC <5> (RO) TCC <6> (RO) TCC <7> (RO) TCC <8> (RO) TCC <9> (RO) TCC <10> (RO) TCC <11> (RO) TCC <12> (RO) TCC <13> (RO) TCC <14> (RO) TCC <15> (RO) Figure 77. Transmit Character Count Register (TCCR) PS97USC0200 86 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM CONTROL REGISTERS (Continued) Address: 11111 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 TC1 <0> TC1 <1> TC1 <2> TC1 <3> TC1 <4> TC1 <5> TC1 <6> TC1 <7> TC1 <8> TC1 <9> TC1 <10> TC1 <11> TC1 <12> TC1 <13> TC1 <14> TC1 <15> Figure 78. Time Constant 1 Register (TC1R) 87 PS97USC0200 P R E L I M I N A R Y ZILOG Address: None Z16C32 IUSCTM * D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 RCC <0> Rx Overrun Parity Error Rx/Frame Abort CRC Error Rx Bound 0 0 0 Short Frame/CV Polarity Residue Code 0 Residue Code 1 Residue Code 2 0 0 First Byte in Error Second Byte in Error * Refer to Figure 22 (Channel Control Register) Bits 6-7 for Access Method Figure 79. Receive Status Block Register (RSBR) PS97USC0200 88 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM CONTROL REGISTERS (Continued) Address: None * D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 Reserved 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 8 Bits 1 Bit 2 Bits 3 Bits 4 Bits 5 Bits 6 Bits 7 Bits HDLC Tx Last Character Length Reserved Tx Submode 0 Tx Submode 1 Tx Submode 2 Tx Submode 3 * Refer to Figure 22 (Channel Control Register) Bits15-14 for Access Method Figure 80. Transmit Status Block Register (TSBR) Address: none D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 Shift Right Address /INT Open-Drain 16-Bit Bus /BUSREQ Type 0 0 1 1 0 1 0 1 Status Acknowledge Single Pulse Acknowledge Reserved Double Pulse Acknowledge INTACK Mode 0* Tri-State All Pins Separate Address for 8-Bit Bus * Must be programmed as 0. Figure 81. Bus Configuration Register (BCR) 89 PS97USC0200 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM ABSOLUTE MAXIMUM RATINGS Symbol Description Min VCC TSTG TA Supply Voltage (*) -0.3 Storage Temp -65 Oper Ambient Temp Power Dissipation Max Units +7.0 +150 2.2 V C C W Stresses greater than those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; operation of the device at any condition above those indicated in the operational sections of these specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Notes: * Voltage on all pins with respect to GND. See Ordering Information. STANDARD TEST CONDITIONS +5V The DC Characteristics and Capacitance Section below apply for the following standard test conditions, unless otherwise noted. All voltages are referenced to Ground. Positive current flows into the referenced pin (Figure 82). Standard conditions are as follows: +4.5 V < VCC < +5.5 V GND = 0 V TA as specified in Ordering Information 1.73 K From Output Under Test 250 A 50 pF Figure 82. Standard Test Load CAPACITANCE Symbol CIN COUT CI/O Parameter Input Capacitance Output Capacitance Bidirectional Capacitance Min Max Unit Condition 10 15 20 pF pF pF * * Notes: F = 1 MHz, over specified temperature range. * Unmeasured pins returned to Ground. MISCELLANEOUS Transistor Count - 100,000 TEMPERATURE RANGE Standard = 0C to 70C PS97USC0200 90 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM IUSC TIMING The IUSC interface timing is similar to that found on a static RAM, except that it is much more flexible. Up to four separate timing strobe signals are present on the interface: /DS, /RD, /WR and /INTACK. Only one of these timing strobes is active at any time. Should the external logic activate more than one of these strobes at the same time, the IUSC will enter a pre-reset state. This state is only exited by a hardware reset. Do not allow overlap of timing strobes. The timing diagrams, beginning on the next page, illustrate the different bus transactions possible with the necessary setup, hold, and delay times. IUSC Timing diagrams are shown from Figure 83 through Figure 107. DC CHARACTERISTICS Symbol Parameter Min VIH VIL VOH1 Input High Voltage Input Low Voltage Output High Voltage 2.2 -0.3 2.4 VOH2 VOL IIL IOL ICC1 Output High Voltage Output Low Voltage Input Leakage Output Leakage VCC Supply Current VCC -0.8 Typ Max Unit VCC +0.3 0.8 V V V V V A A mA 0.4 +10.00 +10.00 50 7 Condition IOH = -1.6 mA IOH = -250 A IOL = +2.0 mA 0.4 < VIN < +2.4V 0.4 < VOUT < +2.4V VCC = 5V VIH = 4.8V VIL = 0.2V Note: VCC = 5V 10% unless otherwise specified, over specified temperature range. AC CHARACTERISTICS Timing Diagrams (Figures 83-105) /RESET 113 114 /STB 115 Figure 83. Reset Timing /STB 112 1 1 Figure 84. Bus Cycle Timing Note: /STB is any of the following: /DS, /RD, /WR or Pulsed /INTACK. 91 PS97USC0200 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM AC CHARACTERISTICS Timing Diagrams (Continued) /CS 12 13 14 15 16 17 S//D, D//C /INTACK (Status) /AS 6 7 2 3 1 R//W 20 21 /DS 4 5 AD15-AD0 18 19 8 10 11 9 /RxREQ 22 23 /WAIT//RDY (Wait) /WAIT//RDY (Ready) 116 79 80 Figure 85. Multiplexed /DS Read Cycle PS97USC0200 92 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM AC CHARACTERISTICS Timing Diagrams (Continued) /CS 12 13 14 15 16 17 S//D, D//C /INTACK (Status) /AS 2 6 7 1 R//W 20 21 /DS 4 5 AD15-AD0 18 19 24 25 /TxREQ 26 27 /WAIT//RDY (Wait) /WAIT//RDY (Ready) 116 80 Figure 86. Multiplexed /DS Write Cycle 93 PS97USC0200 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM /CS 12 13 14 15 16 17 S//D, D//C /INTACK (Status) /AS 2 30 31 1 /RD 28 29 AD15-AD0 18 19 32 34 33 35 /RxREQ 36 37 /WAIT//RDY (Wait) /WAIT//RDY (Ready) 119 79 90 Figure 87. Multiplexed /RD Read Cycle PS97USC0200 94 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM AC CHARACTERISTICS Timing Diagrams (Continued) /CS 12 13 14 15 16 17 S//D, D//C /INTACK (Status) /AS 2 40 41 1 /WR 38 39 AD15-AD0 18 19 42 43 /TxREQ 44 45 /WAIT//RDY (Wait) /WAIT//RDY (Ready) 117 118 Figure 88. Multiplexed /WR Write Cycle 95 PS97USC0200 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM /CS 46 47 48 49 50 51 20 21 S//D, D//C /INTACK (Status) R//W /DS 4 5 1 AD15-AD0 8 10 11 9 /RxREQ 22 23 /WAIT//RDY (Wait) /WAIT//RDY (Ready) 116 79 80 Figure 89. Non-Multiplexed /DS Read Cycle PS97USC0200 96 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM AC CHARACTERISTICS Timing Diagrams (Continued) /CS 46 47 48 49 50 51 20 21 S//D, D//C /INTACK (Status) R//W /DS 4 5 1 AD15-AD0 24 25 /TxREQ 26 27 /WAIT//RDY (Wait) /WAIT//RDY (Ready) 116 80 Figure 90. Non-Multiplexed /DS Write Cycle 97 PS97USC0200 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM /CS 52 53 54 55 56 57 S//D, D//C /INTACK (Status) /RD 28 29 1 AD15-AD0 32 34 33 35 /RxREQ 36 37 /WAIT//RDY (Wait) /WAIT//RDY (Ready) 119 79 90 Figure 91. Non-Multiplexed /RD Read Cycle PS97USC0200 98 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM AC CHARACTERISTICS Timing Diagrams (Continued) /CS 58 59 60 61 62 63 S//D, D//C /INTACK (Status) /WR 38 39 1 AD15-AD0 42 43 /TxREQ 44 45 /WAIT//RDY (Wait) /WAIT//RDY (Ready) 117 118 Figure 92. Non-Multiplexed /WR Write Cycle 99 PS97USC0200 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM /AS 2 6 7 1 /INTACK (Status) 16 17 /DS 4 5 AD15-AD0 18 8 19 10 86 /WAIT//RDY (Wait) 11 87 88 79 /WAIT//RDY (Ready) 78 80 IEI 81 82 IEO 83 84 /INT 85 Figure 93. Multiplexed /DS Interrupt Acknowledge Cycle PS97USC0200 100 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM AC CHARACTERISTICS Timing Diagrams (Continued) /AS 2 30 31 /INTACK (Status) 16 17 /RD 28 29 AD15-AD0 18 32 19 34 94 /WAIT//RDY (Wait) 35 95 88 79 /WAIT//RDY (Ready) 89 90 IEI 91 92 IEO 83 84 /INT 93 Figure 94. Multiplexed /RD Interrupt Acknowledge Cycle 101 PS97USC0200 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM /AS 2 98 99 1 /INTACK (Pulsed) 96 97 AD15-AD0 18 100 19 101 102 109 /WAIT//RDY (Wait) 110 88 79 /WAIT//RDY (Ready) 107 108 IEI 103 104 IEO 83 105 /INT 106 Figure 95. Multiplexed Pulsed Interrupt Acknowledge Cycle PS97USC0200 102 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM AC CHARACTERISTICS Timing Diagrams (Continued) /INTACK (Status) 50 51 /DS 4 5 1 AD15-AD0 8 10 86 11 /WAIT//RDY (Wait) 87 88 79 /WAIT//RDY (Ready) 78 80 IEI 81 82 IEO 83 111 /INT 85 Figure 96. Non-Multiplexed /DS Interrupt Acknowledge Cycle 103 PS97USC0200 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM /INTACK (Status) 56 57 /RD 28 29 1 AD15-AD0 32 34 35 94 /WAIT//RDY (Wait) 95 88 79 /WAIT//RDY (Ready) 89 90 IEI 91 92 IEO 83 111 /INT 93 Figure 97. Non-Multiplexed /RD Pulsed Interrupt Acknowledge Cycle PS97USC0200 104 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM AC CHARACTERISTICS Timing Diagrams (Continued) /INTACK (Pulsed) 96 97 1 AD15-AD0 100 101 79 107 102 /WAIT//RDY (Ready) 108 IEI 103 104 IEO 83 105 /INT 106 109 /WAIT//RDY (Wait) 110 88 Figure 98. Non-Multiplexed Pulsed Interrupt Acknowledge Cycle 105 PS97USC0200 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM /AS 2 98 99 99 2 98 1 1 /INTACK (2-Pulse) 96 96 97 97 AD15-AD0 18 18 19 101 100 19 102 /WAIT//RDY (Ready) 79 107 108 /WAIT//RDY (Wait) 109 110 88 IEI 104 103 IEO 83 105 /INT 106 Figure 99. Multiplexed Double-Pulse Intack Cycle PS97USC0200 106 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM AC CHARACTERISTICS Timing Diagrams (Continued) /INTACK (2-Pulse) 96 96 97 97 1 1 AD15-AD0 101 100 102 /WAIT//RDY (Ready) 107 108 79 /WAIT//RDY (Wait) 109 110 88 IEI 104 103 IEO 83 105 /INT 106 Figure 100. Non-Multiplexed Double-Pulse Intack Cycle 107 PS97USC0200 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM CLK /UAS 171 /AS 171 /DS 171 R//W 171 /RD 171 /WR 171 S//D, D//C 171 AD15-AD0 148 /BUSREQ 170 /BIN 172 173 172 173 Figure 101. DMA Start-Up PS97USC0200 108 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM AC CHARACTERISTICS Timing Diagrams (Continued) CLK 123 120 124 121 122 /UAS 125 127 126 /AS 128 130 129 135 136 /DS 131 133 132 134 R//W 137 142 143 /RD 138 140 139 141 S//D, D//C 144 149 150 151 152 AD15-AD0 148 145 146 147 /WAIT//RDY (Wait) 153 154 155 156 /WAIT//RDY (Ready) /BIN 172 173 168 169 /ABORT Figure 102. Memory Read 109 PS97USC0200 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM CLK 123 120 124 121 122 /UAS 125 127 126 /AS 128 130 129 159 161 /DS 158 160 134 134 R//W 137 163 165 /WR 162 164 166 166 S//D, D//C 144 149 150 151 152 AD15-AD0 145 145 145 157 /WAIT//RDY (Ready) 153 154 155 156 /WAIT//RDY (Wait) /BIN 172 173 168 169 /ABORT Figure 103. Memory Write PS97USC0200 110 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM AC CHARACTERISTICS Timing Diagrams (Continued) CLK /UAS 167 /AS 167 /DS 167 R//W 167 /RD 167 /WR 167 S//D, D//C 167 AD15-AD0 147 Figure 104. Bus Release 111 PS97USC0200 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM CLK /BUSREQ 174 175 /BIN /BOUT 176 Figure 105. Request Timing PS97USC0200 112 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM AC CHARACTERISTICS Timing Table No Symbol Parameter Min 1 2 3 4 Tcyc TwASl TwASh TwDSl Bus Cycle Time /AS Low Width /AS High Width /DS Low Width 160 40 90 70 ns ns ns ns 5 6 7 8 TwDSh TdAS(DS) TdDS(AS) TdDS(DRa) /DS High Width /AS Rise to /DS Fall Delay Time /DS Rise to /AS Fall Delay Time /DS Fall to Data Active Delay 60 5 5 0 ns ns ns ns 9 10 11 12 TdDS(DRv) TdDS(DRn) TdDS(DRz) TsCS(AS) /DS Fall to Data Valid Delay /DS Rise to Data Not Valid Delay /DS Rise to Data Float Delay /CS to /AS Rise Setup Time 15 ns ns ns ns 13 14 15 ThCS(AS) TsADD(AS) ThADD(AS) /CS to /AS Rise Hold Time Direct Address to /AS Rise Setup Time 5 15 ns ns 16 TsSIA(AS) Direct Address to /AS Rise Hold Time Status /INTACK to /AS Rise Setup Time 5 15 ns ns 17 18 19 20 ThSIA(AS) TsAD(AS) ThAD(AS) TsRW(DS) Status /INTACK to /AS Rise Hold Time Address to /AS Rise Setup Time Address to /AS Rise Hold Time R//W to /DS Fall Setup Time 5 15 5 0 ns ns ns ns 21 22 23 24 ThRW(DS) TsDSf(RRQ) TdDSr(RRQ) TsDW(DS) R//W to /DS Fall Hold Time /DS Fall to /RxREQ Inactive Delay /DS Rise to /RxREQ Active Delay Write Data to /DS Rise Setup Time 25 25 26 27 28 ThDW(DS) TdDSf(TRQ) TdDSr(TRQ) TwRDl Write Data to DS Rise Hold Time /DS Fall to /TxREQ Inactive Delay /DS Rise to /TxREQ Active Delay /RD Low Width 0 70 ns ns ns ns 29 30 31 32 TwRDh TdAS(RD) TdRD(AS) TdRD(DRa) /RD High Width /AS Rise to /RD Fall Delay Time /RD Rise to /AS Fall Delay Time /RD Fall to Data Active Delay 60 5 5 0 ns ns ns ns 33 34 35 36 TdRD(DRv) TdRD(DRn) TdRD(DRz) TdRDf(RRQ) /RD Fall to Data Valid Delay /RD Rise to Data Not Valid Delay /RD Rise to Data Float Delay /RD Fall to /RxREQ Inactive Delay 37 38 39 40 TdRDr(RRQ) TwWRl TwWRh TdAS(WR) /RD Rise to /RxREQ Active Delay /WR Low Width /WR High Width /AS Rise to /WR Fall Delay Time 0 70 60 5 ns ns ns ns 41 42 43 44 TdWR(AS) TsDW(WR) ThDW(WR) TdWRf(TRQ) /WR Rise to /AS Fall Delay Time Write Data to /WR Rise Setup Time Write Data to /WR Rise Hold Time /WR Fall to /TxREQ Inactive Delay 5 30 0 ns ns ns ns 113 Max 85 0 20 60 0 30 0 60 85 0 20 60 60 Units ns ns ns ns ns ns ns ns Note [1] [1] [4] [5] [4] [5] PS97USC0200 P R E L I M I N A R Y ZILOG No Symbol Parameter 45 46 47 48 TdWRr(TRQ) TsCS(DS) ThCS(DS) TsADD(DS) /WR Rise to /TxREQ Active Delay /CS to /DS Fall Setup Time /CS to /DS Fall Hold Time Direct Address to /DS Fall Setup Time 49 50 51 52 ThADD(DS) TsSIA(DS) ThSIA(DS) TsCS(RD) 53 54 55 56 Z16C32 IUSCTM Min Max Units Note 0 0 25 5 ns ns ns ns [2] [2] [1,2] Direct Address to /DS Fall Hold Time Status /INTACK to /DS Fall Setup time Status /INTACK to /DS Fall Hold Time /CS to /RD Fall Setup Time 25 5 25 0 ns ns ns ns [1,2] [2] [2] [2] ThCS(RD) TsADD(RD) ThADD(RD) TsSIA(RD) /CS to /RD Fall Hold Time Direct Address to /RD Fall Setup Time Direct Address to /RD Fall Hold Time Status /INTACK to /RD Fall Setup Time 25 5 25 5 ns ns ns ns [2] [1,2] [1,2] [2] 57 58 59 60 ThSIA(RD) TsCS(WR) ThCS(WR) TsADD(WR) Status /INTACK to /RD Fall Hold Time /CS to /WR Fall Setup Time /CS to /WR Fall Hold Time Direct Address to /WR Fall Setup Time 25 0 25 5 ns ns ns ns [2] [2] [2] [1,2] 61 62 63 78 ThADD(WR) TsSIA(WR) ThSIA(WR) TdDSf(RDY) Direct Address to /WR Fall Hold Time Status /INTACK to /WR Fall Setup Time Status /INTACK to /WR Fall Hold Time /DS Fall (Intack) to /RDY Fall Delay 25 5 25 ns ns ns ns [1,2] [2] [2] 79 80 81 82 TdRDY(DRv) TdDSr(RDY) TsIEI(DSI) ThIEI(DSI) /RDY Fall to Data Valid Delay /DS Rise to /RDY Rise Delay IEI to /DS Fall (Intack) Setup Time IEI to /DS Rise (Intack) Hold Time 83 84 85 86 TdIEI(IEO) TdAS(IEO) TdDSI(INT) TdDSI(Wf) 87 88 89 90 200 40 40 ns ns ns ns IEI to IEO Delay /AS Rise (Intack) to IEO Delay /DS Fall to /INT Inactive Delay /DS Fall (Intack) to /WAIT Fall Delay 60 60 200 40 ns ns ns ns TdDSI(Wr) TdW(DRv) TdRDf(RDY) TdRDr(RDY) /DS Fall (Intack) to /WAIT Rise Delay /WAIT Rise to Data Valid Delay /RD Fall (Intack) to /RDY Fall Delay /RD Rise to /RDY Rise Delay 200 40 200 40 ns ns ns ns 91 92 93 TsIEI(RDI) ThIEI(RDI) TdRDI(INT) IEI to /RD Fall (Intack) Setup Time IEI to /RD Rise (Intack) Hold Time 94 TdRDI(Wf) /RD Fall (Intack) to /INT Inactive Delay /RD Fall (Intack) to /WAIT Fall Delay 95 96 97 98 TdRDI(Wr) TwPIAl TwPIAh TdAS(PIA) /RD Fall (Intack) to /WAIT Rise Delay Pulsed /INTACK Low Width Pulsed /INTACK High Width /AS Rise to Pulsed /INTACK Fall Delay Time 99 100 101 102 TdPIA(AS) TdPIA(DRa) TdPIA(DRn) TdPIA(DRz) Pulsed /INTACK Rise to /AS Fall Delay Time Pulsed /INTACK Fall to Data Active Delay Pulsed /INTACK Rise to Data Not Valid Delay Pulsed /INTACK Rise to Data Float Delay PS97USC0200 60 0 60 0 ns ns 200 40 ns ns 200 ns ns ns ns 70 60 5 5 0 0 20 ns ns ns ns 114 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM AC CHARACTERISTICS (Continued) Timing Table No Symbol Parameter Min 103 104 105 106 TsIEI(PIA) ThIEI(PIA) TdPIA(IEO) TdPIA(INT) IEI to Pulsed /INTACK Fall Setup Time IEI to Pulsed /INTACK Rise Hold Time Pulsed /INTACK Fall to IEO Delay Pulsed /INTACK Fall to /INT Inactive Delay 10 0 107 108 109 110 TdPIAf(RDY) TdPIAr(RDY) TdPIA(Wf) TdPIA(Wr) Pulsed /INTACK Fall to /RDY Fall Delay Pulsed /INTACK Rise to /RDY Rise Delay Pulsed /INTACK Fall to /WAIT Fall Delay Pulsed /INTACK Fall to /WAIT Rise Delay 111 112 113 114 TdSIA(INT) TwSTBh TwRESl TwRESh Status /INTACK Fall to IEO Inactive Delay /Strobe High Width /RESET Low Width /RESET High Width 115 116 117 118 TdRES(STB) TdDSf(RDY) TdWRf(RDY) TdWRr(RDY) /RESET Rise to /STB Fall /DS Fall to /RDY Fall Delay /WR Fall to /RDY Fall Delay /WR Rise to /RDY Rise Delay 119 120 121a 121b 122a 122b TdRDf(RDY) TwCLKl TwCLKh TwCLKh TcCLK TcCLK /RD Fall to /RDY Fall Delay CLK Low Width CLK High Width CLK High Width (Linked List Mode) CLK Cycle Time CLK Cycle Time (Linked List Mode) 123 124 125 126 TfCLK TrCLK TdCLKr (UAS) TwUASl CLK Fall Time CLK Rise Time CLK Rise to /UAS Fall Delay /UAS Low Width 127 128 129 130 TdCLKf(UAS) TdCLKr(AS) TwASl TdCLKf(AS) CLK Fall to /UAS Rise Delay CLK Rise to /AS Fall Delay /AS Low Width CLK Fall to /AS Rise Delay 131 132 133 134 TdAS(DSr) TdCLKr(DS) TwDSlr TdCLKf(DS) /AS Rise to /DS Fall (Read) Delay CLK Rise to /DS Delay /DS (Read) Low Width CLK Fall to /DS Delay 25 135 136 137 138 TsDR(DS) ThDR(DS) TdCLK(RW) TdAS(RD) Read Data to /DS Rise Setup Time Read Data to /DS Rise Hold Time CLK Rise to R//W Delay /AS Rise to /RD Fall Delay 30 0 139 140 141 142 TdCLKr(RD) TwRDl TdCLKf(RD) TsDR(RD) CLK Rise to /RD Delay /RD Low Width CLK Fall to /RD Delay Read Data to /RD Rise Setup Time 143 144 145 146 ThDR(RD) TdCLK(ADD) TdCLK(AD) ThAD(PC) Read Data to /RD Rise Hold Time CLK Rise to Direct Address Delay CLK Rise to Address Delay Address to CLK Rise Hold Time 115 Max Units 60 200 ns ns ns ns 200 40 40 200 ns ns ns ns 200 ns ns ns ns [2] [3] ns ns ns ns [3] 50 170 60 60 50 50 40 50 ns ns ns ns ns ns [12] 5 5 30 ns ns ns ns [6] [6,7,13] 30 30 ns ns ns ns [6] [6] [6,7,13] [6] ns ns ns ns [6,8] [6] [6,9,13] [6] ns ns ns ns [6] [6] [6] [6,8] ns ns ns ns [6] [6,9] [6] [6] ns ns ns ns [6] [1,6] [6] [6] 25 25 35 50 60 25 25 30 30 75 30 30 25 30 75 30 30 0 TdCLKf(DS) 0 Note 30 35 [12] PS97USC0200 P R E L I M I N A R Y ZILOG No Symbol Parameter 147 148 149 150 TdCLK(ADz) TdCLK(ADa) TsAD(UAS) ThAD(UAS) CLK Rise to Address Float Delay CLK Rise to Address Active Delay Address to /UAS Rise Setup Time Address to /UAS Rise Hold Time 151 152 153 154 TsAD(AS) ThAD(AS) TsW(CLK) ThW(CLK) 155 156 157 158 Z16C32 IUSCTM Max Units Note 35 35 10 10 ns ns ns ns [6] [6] [6] [6] Address to /AS Rise Setup Time Address to /AS Rise Hold Time /WAIT to CLK Fall Setup Time /WAIT to CLK Fall Hold Time 10 10 10 15 ns ns ns ns [6] [6] [6] [6] TsRDY(CLK) ThRDY(CLK) ThDW(CLK) TdAS(DSw) /READY to CLK Fall Setup Time /READY to CLK Fall Hold Time Write Data to CLK Rise Hold Time /AS Rise to /DS Fall (Write) Delay 10 15 0 40 ns ns ns ns [6] [6] [6] [6,10,13] 159 160 161 162 TsDW(DS) TwDSlw ThDW(DS) TdAS(WR) Write Data to /DS Fall Setup Time /DS (Write) Low Width Write Data to /DS Rise Hold Time /AS Rise to /WR Fall Delay 25 45 25 40 ns ns ns ns [6,7,13] [6,11,13] [6,8] [6,10,13] 163 164 165 166 TsDW(WR) TwWRl ThDW(WR) TdCLK(WR) Write Data to /WR Fall Setup Time /WR Low Width Write Data to /WR Rise Hold Time CLK Fall to /WR Delay 25 45 25 ns ns ns ns [6,7,13] [6,11,13] [6,8] [6] 167 168 169 170 TdCLK(BUSz) TsABT(CLK) ThABT(CLK) TdCLK(BRQ) CLK Rise to Bus Float Delay /ABORT to CLK Rise Setup Time /ABORT to CLK Rise Hold Time CLK Rise to /BUSREQ Delay 20 15 ns ns ns ns [6] [6] [6] [6] 171 172 173 174 175 176 TdCLK(BUSa) TsBIN(CLK) ThBIN(CLK) TsBRQ(CLK) ThBRQ(CLK) TdBIN(BOT) CLK Rise to Bus Active Delay /BIN to CLK Rise Setup Time /BIN to CLK Rise Hold Time /BUSREQ to CLK Rise Setup Time /BUSREQ to CLK Rise Hold Time /BIN to /BOUT Delay 20 15 25 0 ns ns ns ns ns ns [6] [6] [6] [6] [6] Notes: AC Test Conditions: VCC = 5V 5% unless otherwise specified, over specified temperature range. VIH = 2.0V VOH = 2.0V VIL = 0.8V VOL = 0.8V Float = +0.5V [1] [2] [3] [4] [5] [6] Direct Address is any of S//D, D//C or AD15-AD8 used as an address bus. The parameter applies only when /AS is not present. Strobe is any of /DS, /RD, /WR or Pulsed /INTACK. Parameter applies only if read empties the receive FIFO. Parameter applies only if write fills the transmit FIFO. Parameter applies only while the IUSC is bus master. PS97USC0200 Min [7] [8] [9] [10] [11] [12] [13] 30 30 30 30 60 Parameter is clock-cycle dependent, TwCLKh + TfCLK - 5. Parameter is clock-cycle dependent, TwCLKl + TrCLK -5 Parameter is clock-cycle dependent, TcCLK + TwCLKh + TfCLK -5. Parameter is clock-cycle dependent, TcCLK -10. Parameter is clock-cycle dependent, TcCLK -5. Clock cycle parameters TwCLKh and TcCLK have unique values for Linked List Mode. In Linked List Mode, the system clock cycle is extended to 60 ns, and the system clock High pulse width is extended to 35 ns. This is due to the internal timing paths unique to the Linked List Mode. The transmit and receive bit rates are not affected. For Linked List Mode, the minimum for these values should be calculated using TwCLKh = 35 ns and TcCLK = 60 ns. 116 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM AC CHARACTERISTICS General Timing Diagram /RxC, /TxC Receive 1 3 2 4 RxD 5 6 /DCD as /SYNC External /TxC, /RxC Transmit 7 8 TxD 9 10 /RxC 11 /TxC 12 13 14 /CTS, /DCD 15 15 16 16 /DCD as /SYNC Input Figure 106. General Timing 117 PS97USC0200 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM AC CHARACTERISTICS General Timing Table No Symbol Parameter Min 1 2 3 4 TsRxD(RxCr) ThRxD(RxCr) TsRxd(RxCf) ThRxD(RxCf) RxD to /RxC Rise Setup Time (x1 Mode) RxD to /RxC Rise Hold Time (x1 Mode) RxD to /RxC Fall Setup Time (x1 Mode) RxD to /RxC Fall Hold Time (x1 Mode) 5 6 7 8 TsSy(RxC) ThSy(RxC) TdTxCf(TxD) TdTxCr(TxD) 9 10 11 12 13 14 15 16 Units Note 0 20 0 20 ns ns ns ns [1] [1] [1,3] [1,3] /DCD as /SYNC to /RxC Rise Setup Time /DCD as /SYNC to /RxC Rise Hold Time (x1 Mode) /TxC Fall to TxD Delay /TxC Rise to TxD Delay 0 20 ns ns ns ns [1] [1] [2] [2,3] TwRxCh TwRxCl TcRxC TwTxCh /RxC High Width /RxC Low Width /RxC Cycle Time /TxC High Width 20 20 50 20 ns ns ns ns TwTxCl TcTxC TwExT TWSY /TxC Low Width /TxC Cycle Time /DCD or /CTS Pulse Width /DCD as /SYNC Input Pulse Width 20 50 35 35 ns ns ns ns PS97USC0200 Max 25 25 118 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM AC CHARACTERISTICS System Timing Diagram /RxC, /TxC Receive /RxREQ Request 1 /RxC as Receiver Output 2 /INT 3 /RxC, /TxC Transmit /TxREQ 4 /TxC as Transmitter Output 5 /INT 6 /CTS, /DCD, /TxREQ, /RxREQ /INT 7 Figure 107. Z16C32 System Timing 119 PS97USC0200 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM AC CHARACTERISTICS System Timing Table No Symbol Parameter 1 2 3 4 TdRxC(REQ) TdRxC(RxC) TdRxC(INT) TdTxC(REQ) 5 6 7 TdTxC(TxC) TdTxC(INT) TdEXT(INT) Min Max Units Note /RxC Rise to /RxREQ Valid Delay /TxC Rise to /RxC as Receiver Output Valid Delay /RxC Rise to /INT Valid Delay /TxC Fall to /TxREQ Valid Delay 50 50 50 50 ns ns ns ns [2] [2] [2] [2] /RxC Fall to /TxC as transmitter Output Valid Delay /TxC Fall to /INT Valid Delay /CTS, /DCD, /TxREQ, /RxREQ transition to /INT Valid Delay 50 50 ns ns [2] 50 ns Notes: [1] /RxC is /RxC or /TxC, whichever is supplying the receive clock. [2] /TxC is /TxC or /RxC, whichever is supplying the transmit clock. [3] Parameter applies only to FM encoding/decoding. PS97USC0200 120 ZILOG P R E L I M I N A R Y Z16C32 IUSCTM PACKAGE INFORMATION 68-Pin PLCC Package Diagram 121 PS97USC0200 P R E L I M I N A R Y ZILOG Z16C32 IUSCTM ORDERING INFORMATION Z16C32 IUSC 20 MHz 68-Pin PLCC Z16C3220VSC For fast results, contact your local Zilog sales office for assistance in ordering the part desired. Package V = Plastic Chip Carrier Temperature S = 0C to 70C Speed 20 = 20 MHz Environmental C = Plastic Standard Example: Z 16C32 20 V S C is a Z16C32, 20 MHz, PLCC, 0C to +70C, Plastic Standard Flow Environmental Flow Temperature Package Speed Product Number Zilog Prefix (c) 1997 by Zilog, Inc. All rights reserved. No part of this document may be copied or reproduced in any form or by any means without the prior written consent of Zilog, Inc. The information in this document is subject to change without notice. Devices sold by Zilog, Inc. are covered by warranty and patent indemnification provisions appearing in Zilog, Inc. Terms and Conditions of Sale only. Zilog, Inc. makes no warranty, express, statutory, implied or by description, regarding the information set forth herein or regarding the freedom of the described devices from intellectual property infringement. Zilog, Inc. makes no warranty of merchantability or fitness for any purpose. Zilog, Inc. shall not be responsible for any errors that may appear in this document. Zilog, Inc. makes no commitment to update or keep current the information contained in this document. PS97USC0200 Zilog's products are not authorized for use as critical components in life support devices or systems unless a specific written agreement pertaining to such intended use is executed between the customer and Zilog prior to use. Life support devices or systems are those which are intended for surgical implantation into the body, or which sustains life whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in significant injury to the user. Zilog, Inc. 210 East Hacienda Ave. Campbell, CA 95008-6600 Telephone (408) 370-8000 Telex 910-338-7621 FAX 408 370-8056 Internet: http://www.zilog.com 122