CSM_E2EH_DS_E_4_1
1
Proximity Sensor Ideal for High Temperatures and Cleaning Processes
E2EH
Proximity Sensor Ideal for the Food
and Beverage Industry
–SUS316L Body, IP69K Protection, Resistant to High
Temperatures and Detergents–
Improved resistance to
detergents and rusting
Applicable to 120°C
(with DC 3-wire
connection)
(Heat resistance verified
to 1,000 hours.)
Resists typical
detergents and
disinfectants used in
the food industry
Water resistant under
high-temperature,
high-pressure cleaning
based on DIN 40050-9.
(Pressure: 8,000 to
10,000 kPa, Water
temperature: 80°C, For
30 s at all angles)
Be sure to read Safety Precautions on page 9.
Ordering Information
Sensors [Refer to Dimensions on page 10.]
Pre-wired Models *1
Connector Models (M12)
*1. The standard cable length is 2 m. An optional 5 m model is also available. Contact your OMRON representative for more information.
For details, refer to the Proximity Sensors Technical Guide.
*2. When using a no-polarity model, there is no need to be concerned about whether to connect to the positive or negative side of the power supply. The load can be
connected to either the +V side or 0 V side.
Appearance Sensing distance Output configuration Operation mode: NO Operation mode: NC
M12
DC 2-wire (polarity) E2EH-X3D1 2M E2EH-X3D2 2M
DC 2-wire (no polarity) *2E2EH-X3D1-T 2M ---
DC 3-wire (PNP) E2EH-X3B1 2M E2EH-X3B2 2M
DC 3-wire (NPN)E2EH-X3C1 2M E2EH-X3C2 2M
M18
DC 2-wire (polarity) E2EH-X7D1 2M E2EH-X7D2 2M
DC 2-wire (no polarity) *2E2EH-X7D1-T 2M ---
DC 3-wire (PNP) E2EH-X7B1 2M E2EH-X7B2 2M
DC 3-wire (NPN)E2EH-X7C1 2M E2EH-X7C2 2M
M30
DC 2-wire (polarity) E2EH-X12D1 2M E2EH-X12D2 2M
DC 2-wire (no polarity) *2E2EH-X12D1-T 2M ---
DC 3-wire (PNP) E2EH-X12B1 2M E2EH-X12B2 2M
DC 3-wire (NPN)E2EH-X12C1 2M E2EH-X12C2 2M
Shielded
3 mm
7 mm
12 mm
Appearance Sensing distance Output configuration Operation mode: NO Operation mode: NC
M12
DC 2-wire (polarity) E2EH-X3D1-M1G E2EH-X3D2-M1G
DC 3-wire (PNP) E2EH-X3B1-M1 E2EH-X3B2-M1
DC 3-wire (NPN)E2EH-X3C1-M1 E2EH-X3C2-M1
M18
DC 2-wire (polarity) E2EH-X7D1-M1G E2EH-X7D2-M1G
DC 3-wire (PNP) E2EH-X7B1-M1 E2EH-X7B2-M1
DC 3-wire (NPN)E2EH-X7C1-M1 E2EH-X7C2-M1
M30
DC 2-wire (polarity) E2EH-X12D1-M1G E2EH-X12D2-M1G
DC 3-wire (PNP) E2EH-X12B1-M1 E2EH-X12B2-M1
DC 3-wire (NPN)E2EH-X12C1-M1 E2EH-X12C2-M1
Shielded
3 mm
7 mm
12 mm
E2EH
2
Accessories (Order Separately)
Sensor I/O Connectors (M12)
(Models for Connectors: A Connector is not provided with the Sensor. Be sure to order a Connector separately.)
[Refer to XS2.]
Note: The above Connectors conform to DIN40050-9 standard, provide IP69K protection, have a maximum operating temperature of 105°C, and use SUS316L stainless
steel.
Appearance Cable length Sensor I/O Connector model Applicable Proximity Sensors
2 m XS2F-E421-D80-E
E2EH-X@D@-M1G
E2EH-X@B@-M1
E2EH-X@C@-M1
5 m XS2F-E421-G80-E
2 m XS2F-E422-D80-E
5 m XS2F-E422-G80-E
Straight
L-shape
E2EH
3
Ratings and Specifications
E2EH-X@D@ DC 2-Wire Models
*1. Use the yellow indicator on D1 Models as a guide.
*2. The response frequency is an average value.
Measurement conditions are as follows: standard sensing object, a distance of twice the standard sensing object, and a set distance of half the sensing distance.
*3. The residual voltage of each E2EH-X@D@ DC 2-Wire Model is 5 V. When connecting to a device, make sure that the device can withstand the residual voltage.
(Refer to page 9.)
*4. Operation with power supplied for 1,000 h has been verified at 110°C. Do not bend the cable repeatedly at 100°C or higher.
*5. IP69K Degree of Protection Specification
IP69K is a protection standard against high temperature and high-pressure water defined in the German standard DIN 40050,
Part 9. The test piece is sprayed with water at 80°C at a water pressure of 80 to 100 BAR using a specified nozzle shape at a
rate of 14 to 16 liters/min.
The distance between the test piece and nozzle is 10 to 15 cm, and water is sprayed horizontally for 30 seconds each at 0°,
30°, 60°, and 90° while rotating the test piece on a horizontal plane.
Size M12 M18 M30
Shielded Shielded
Item Model E2EH-X3D@E2EH-X7D@E2EH-X12D@
Sensing distance 3 mm 7 mm 12 mm
Set distance *10 to 2.4 mm 0 to 5.6 mm 0 to 9.6 mm
Differential travel 15% max. of sensing distance
Detectable object Ferrous metal (The sensing distance decreases with non-ferrous metal.
Refer to Engineering Data on page 6.)
Standard sensing object Iron, 12 × 12 × 1 mm Iron 21 × 21 × 1 mm Iron 36 × 36 × 1 mm
Response frequency *2500 Hz 300 Hz 100 Hz
Power supply voltage (operating
voltage range)
12 to 24 VDC, ripple (p-p): 10% max.
(10 to 32 VDC, however, 24 VDC max. at temperatures over 100°C)
Leakage current 0.8 mA max.
Control out-
put
Load current 3 to 100 mA (however, 3 to 50 mA at 100 to 110°C)
Residual voltage *3Polarity Models: 3 V max.
No polarity Models: E2EH-X@D@-T: (5 V max. *3 (Load current: 100 mA, Cable length 2 m)
Indicators D1 Models: Operation indicator (red), Setting indicator (yellow)
D2 Models: Operation indicator (yellow)
Operation mode (with sensing ob-
ject approaching)
D1 Models: NO
D2 Models: NC
Protection circuits Surge suppressor, Load short-circuit protection
Ambient temperature range Operating: 0 to 100°C (0 to 110°C 1,000 h) *4
Storage: −25 to 70° (with no icing or condensation)
Ambient humidity range 35% to 95%
Temperature influence
±10% max. of sensing distance at 23°C in the temperature range of 0 to 70°C.
±15% max. of sensing distance at 23°C in the temperature range of 70 to 100°C.
−15% to +20% of sensing distance at 23°C in the temperature range of 100 to 110°C.
Voltage influence ±10% max. of sensing distance at rated voltage in the 15% rated voltage range.
Insulation resistance 50 MΩ min. (at 500 VDC) between current-carrying parts and case
Dielectric strength 1,000 VAC, 50/60 Hz for 1 min between current-carrying parts and case
Vibration resistance Destruction: 10 to 55 Hz 1.5-mm double amplitude for 2 hours each in X, Y and Z directions
Shock resistance Destruction: 1,000 m/s2, 10 times each in X, Y and Z directions
Degree of protection IEC IP67, DIN 40050-9 IP69K *5
Connection method Pre-wired Models (Standard cable length 2 m), Connector Models
Weight
(packed state)
Pre-wired Models Approx. 80 g Approx. 145 g Approx. 220 g
Connector Models Approx. 30 g Approx. 55 g Approx. 125 g
Materials
Case, clamping nut Stainless steel (SUS316L)
Sensing surface PBT
Cable Heat-resistant PVC cable (Pre-wired model)
Accessories Instruction manual
Refer to the timing charts under I/O Circuit Diagrams on page 7 for details.
E2EH
4
E2EH-X@C@/B@ DC 3-Wire Models
*1. The response frequency is an average value.
Measurement conditions are as follows: standard sensing object, a distance of twice the standard sensing object, and a set distance of half the sensing distance.
*2. Operation with power supplied for 1,000 h has been verified at 120°C. Do not bend the cable repeatedly at 100°C or higher.
Size M12 M18 M30
Shielded Shielded
Item Model E2EH-X3C@/B@E2EH-X7C@/B@E2EH-X12C@/B@
Sensing distance 3 mm±10% 7 mm±10% 12 mm±10%
Set distance *10 to 2.4 mm 0 to 5.6 mm 0 to 9.6 mm
Differential travel 15% max. of sensing distance
Detectable object Ferrous metal (The sensing distance decreases with non-ferrous metal. Refer to Engineering
Data on page 6.)
Standard sensing object Iron, 12 × 12 × 1 mm Iron 21 × 21 × 1 mm Iron 36 × 36 × 1 mm
Response frequency *2500 Hz 300 Hz 100 Hz
Power supply voltage (operating
voltage range)
12 to 24 VDC, ripple (p-p): 10% max.
(10 to 32 VDC, however, 24 VDC max. at temperatures over 100°C)
Current consumption 10 mA max.
Control out-
put
Load current 100 mA max. (however, 50 mA max. at 100 to 120°C)
Residual voltage 2 V max. (Load current: 100 mA, Cable length 2 m)
Indicators Operation indicator (yellow)
Operating mode
(with sensing object approaching)
C1 Models: NO
C2 Models: NC
B1 Models: NO
B2 Models: NC
Protection circuits Power supply reverse polarity protection, Surge suppressor, Load short-circuit protection,
Reversed output polarity protection
Ambient temperature range Operating: 0 to 100°C (0 to 120°C 1,000 h) *2
Storage: −25 to 70°C (with no icing or condensation)
Ambient humidity range 35% to 95%
Temperature influence
±10% max. of sensing distance at 23°C in the temperature range of 0 to 70°C.
±15% max. of sensing distance at 23°C in the temperature range of 70 to 100°C.
−15% to 20% of sensing distance at 23°C in the temperature range of 100 to 120°C.
Voltage influence 10% max. of sensing distance at rated voltage in the 15% rated voltage range.
Insulation resistance 50 MΩ min. (at 500 VDC) between current-carrying parts and case
Dielectric strength 1,000 VAC, 50/60 Hz for 1 min between current-carrying parts and case
Vibration resistance Destruction: 10 to 55 Hz 1.5-mm double amplitude for 2 hours each in X, Y and Z directions
Shock resistance Destruction: 1,000 m/s2, 10 times each in X, Y and Z directions
Degree of protection IEC IP67, DIN 40050-9 IP69K
Connection method Pre-wired Models (Standard cable length 2 m), Connector Models
Weight
(packed state)
Pre-wired Models Approx. 80 g Approx. 145 g Approx. 220 g
Connector Models Approx. 30 g Approx. 55 g Approx. 125 g
Materials
Case, clamping nut Stainless steel (SUS316L)
Sensing surface PBT
Cable Heat-resistant PVC cable (Pre-wired Model)
Accessories Instruction manual
Refer to the timing charts under I/O Circuit Diagrams on page 7 for details.
E2EH
5
Resistance to Detergents, Disinfectants, and Chemicals
•Performance is assured for typical detergents and disinfectants, but performance may not be maintained for some detergents
and disinfectants. Refer to the following table when using these agents.
•The E2EH passed testing for resistance to detergents and disinfectants performed using the items in the following table. Refer
to this table when considering use of detergents and disinfectants.
Test Conditions
After the test is completed, check that no problems exist with the following product
characteristics.
(1) Appearance (no damage that will affect the product characteristics)
(2) Operation Check (ON/OFF)
(3) Insulation resistance: 50 MΩ min. (at 500 VDC)
(4) Dielectric strength (1,000 VAC for 1 minute)
(5) Water resistance (IP67)
Category Product name Concentration Temperature Time
Chemical
Sodium hydroxide (NaOH) 1.5% 70°C240h
Potassium hydroxide (KOH) 1.5% 70°C240h
Phosphoric acid (H3PO4)2.5%70°C240h
Sodium hypochlorite (NaClO) 0.3% 25°C240h
Hydrogen peroxide (H2O2)6.5%25°C240h
Alkaline foam
detergent P3-topax-66s (Manufactured by Ecolab)3.0%70°C240h
Acidic foam detergent P3-topax-56 (Manufactured by Ecolab)5.0%70°C240h
Disinfectant P3-oxonia active 90 (Manufactured by Ecolab)1.0% 25°C240h
Te s t l i quid
Depth: 10 cm
Sensor
E2EH
6
Engineering Data
Sensing Area
Shielded Models
E2EH-X@@
Influence of Sensing Object Size and Material
E2EH-X3@@ E2EH-X7@@ E2EH-X12@@
Residual Output Voltage Leakage Current
E2EH-X@D@E2EH-X@D@
(Typical)
Distance Y (mm)
18
16
14
12
10
8
6
4
2
0
E2EH-X12@
E2EH-X7@
E2EH-X3@
−20 −15 −10 −50 5101520
Distance X (mm)
X
Y
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0 5 10 15 20 25 30
Side length of sensing object: d (mm)
Iron
Brass
Aluminum
Copper
Stainless steel (SUS304)
@d
t = 1 mm
X
Distance X (mm)
@dt = 1 mm
X
Side length of sensing object: d (mm)
Distance X (mm)
8
7
6
5
4
3
2
1
0 5 10 15 20 25 30 4035
Iron
Brass
Copper
Aluminum
Stainless steel (SUS304)
@d
t = 1 mm
X
14
12
10
8
6
4
2
0 10 20 30 40 50
Distance X (mm)
Side length of sensing object: d (mm)
Iron
Brass
Copper
Aluminum
Stainless steel (SUS304)
E2EH-X@D@-T
E2EH-X@D@
1 3 5 10 30 50 100
Load current (mA)
5
4
3
2
1
0
Residual load voltage (V)
1.0
0.8
0.6
0.4
0.2
0 5 10 15 20 25 30
Power supply voltage (V)
E2EH-X@D@
Leakage current (mA)
E2EH
7
I/O Circuit Diagrams
E2EH-X@D@ DC 2-Wire Models
DC 3-Wire Models
Operating
mode Model Timing charts Output circuit
NO
E2EH-X@D1
E2EH-X@D1-M1G
E2EH-X@D1-T
NCE2EH-X@D2
E2EH-X@D2-M1G
Operating
mode
Output
specifications Model Timing charts Output circuit
NO
NPN
Open-collector
output
E2EH-X@C1
NCE2EH-X@C2
NO
PNP
Open-collector
output
E2EH-X@B1
NCE2EH-X@B2
Sensing
object
(%)100 080
Stable sensing areaNon-sensing area
Set position
Proximity Sensor
ON
OFF
ON
OFF
ON
OFF
Setting indicator
(yellow)
Operation indicator
(red)
Control output
Unstable
sensing
area
Rated
sensing
distance
Load
Brown
(1)
Blue
(4)
+V
0 V
Polarity: Yes
Note: The load can be connected to either
the +V or 0 V side.
Proximity
Sensor
main
circuit
+V
(0 V)
0 V
(+V)
Load
Polarity: None
Proximity
Sensor
main
circuit
Note: 1. The load can be connected to either the
+V or 0 V side.
2. The E2EH-X@D@-T has no polarity.
Therefore, you do not need to consider
the polarity.
Sensing
object
(%)100 0
Sensing areaNon-sensing area
Proximity sensor
ON
OFF
ON
OFF
Operation indicator
(yellow)
Control output
Rated
sensing
distance
Load
Brown
(1)
Blue
(2)
Proximity
Sensor
main
circuit
+V
0 V
Note: The load can be connected to either
the +V or 0 V side.
Present
Not present
ON
OFF
ON
OFF
Operation indicator
(yellow)
Sensing object
Control output
Black
+V
0 V
(1)
(3)
(4) (2)
Note: Use pin 1, 4, and 3 for NO.
Use pin 1, 2, and 3 for NC.
or
Load
Brown
Blue
Proximity
Sensor
main
circuit
Present
Not present
ON
OFF
ON
OFF
Operation indicator
(yellow)
Sensing object
Control output
Present
Not present
ON
OFF
ON
OFF
Operation indicator
(yellow)
Sensing object
Control output
+V
0 V
Black
(1)
(3)
(4) (2)
Note: Use pin 1, 4, and 3 for NO.
Use pin 1, 2, and 3 for NC.
Load
Brown
Blue
Proximity
Sensor
main
circuit
Present
Not present
ON
OFF
ON
OFF
Operation indicator
(yellow)
Sensing object
Control output
E2EH
8
Connections for Sensor I/O Connectors
*XS2F wire colors differ from Proximity Sensor wire colors.
Con-
nection
diagram
No.
Proximity Sensor
Sensor I/O
Connector model Connections
Type Operating
mode Model
1
DC 2-wire
(IEC pin
wiring)
NOE2EH-X@D1-M1G
2NCE2EH-X@D2-M1G
3
DC 3-wire
NOE2EH-X@B1-M1
E2EH-X@C1-M1
4NCE2EH-X@B2-M1
E2EH-X@C2-M1
Refer to the Sensor I/O Connector Group Catalog (Cat. No. X073) for details.
XS2F-E42@-@80-E
1: Straight
2: L-shape
D: 2-m cable
G: 5-m cable
Main circuit
1
2
3
4
1
2
3
4
E2EH XS2F *
Brown (+)
White (not connected)
Blue (not connected)
Black (−)
1
2
3
4
1
2
3
4
E2EH XS2F *
Brown (+)
White (−)
Blue (not connected)
Black (not connected)
Main circuit
1
2
3
4
1
2
3
4
E2EH XS2F *
Brown (+V)
White (not connected)
Blue (0 V)
Black (output)
Main circuit
E2EH XS2F *
1
2
3
4
1
2
3
4
Brown (+V)
White (output)
Blue (0 V)
Black (not connected)
Main circuit
E2EH
9
Safety Precautions
Refer to Warranty and Limitations of Liability for details.
This product is not designed or rated for
ensuring safety of persons either directly or
indirectly. Do not use it for such purposes.
Do not use this product under ambient conditions that exceed
the ratings.
● Design
Influence of Surrounding Metal
When mounting the Sensor within a metal panel, ensure that
the clearances given in the following table are maintained.
Influence of Surrounding Metal (Unit: mm)
AND/OR Connections
Error pulses and leakage current may prevent application in
AND or OR circuits. Always confirm operation in advance to
confirm if there are any problems in operation.
Mutual Interference
When installing Sensors face-to-face or side-by-side, ensure
that the minimum distances given in the following table are
maintained.
Mutual Interference (Unit: mm)
WARNING
Precautions for Correct Use
Type Item M12 M18 M30
DC 2-wire E2EM-
X@D@Shielded
l2.43.66
d1827 50
D2.43.6 6
m122445
n1827 50
DC 3-wire
E2EH-X@B@
E2EH-X@C@
Shielded
l2.43.66
d1827 50
D2.43.6 6
m122445
n1827 50
l
m
n
l
m
D
d dia.
Type Item M12 M18 M30
DC 2-wire
E2EH-X@D@Shielded A3060110
B203590
DC 3-wire
E2EH-X@B@
E2EH-X@C@
Shielded
A3060110
B203590
A
A
B
Connecting a DC 2-wire Proximity Sensor to a PLC (Programmable Controller)
Required Conditions
Connection to a PLC is possible if the specifications of the PLC and Proximity Sensor satisfy
the following conditions. (The meanings of the symbols are given below.)
1. The ON voltage of the PLC and the residual voltage of the Proximity Sensor must satisfy
the following.
VON ≤ VCC − VR
2. The OFF current of the PLC and the leakage current of the Proximity Sensor must satisfy
the following.
IOFF ≥ Ileak
(If the OFF current is not listed in the specifications, take it to be 1.3 mA.)
3. The ON current of the PLC and the control output of the Proximity Sensor must satisfy the
following.
IOUT (min) ≤ ION ≤ IOUT (max)
The ON current will vary, however, with the power supply voltage and the input impedance,
as shown in the following equation.
ION = (VCC − VR − VPC) / RIN
Example
In this example, the above conditions are checked when the PLC Unit is the C200H-ID212,
the Proximity Sensor is the E2EH-X7D1-T, and the power supply voltage is 24 V.
1. VON (14.4 V) ≤ VCC (20.4 V) − VR (5 V) = 15.4 V : OK
2. IOFF (1.3 mA) ≥ Ileak (0.8 mA) : OK
3. ION = [VCC (20.4 V) − VR (5 V) − VPC (4 V)] / RIN (3 kΩ) ≅ Approx. 3.8 mA
Therefore, IOUT (min) (3 mA) ≤ ION (3.8 mA) : OK
VON:ON voltage of PLC (14.4 V)
ION:ON current of PLC (typ. 7 mA)
IOFF: OFF current of PLC (1.3 mA)
RIN:Input impedance of PLC (3 kΩ)
VPC: Internal residual voltage of PLC (4 V)
VR: Output residual voltage of Proximity Sensor (5 V)
Ileak: Leakage current of Proximity Sensor (3 to 100 mA)
IOUT: Control output of Proximity Sensor (3 to 100 mA)
VCC: Power supply voltage (PLC: 20.4 to 26.4 V)
Values in parentheses apply to the following PLC model
and Proximity Sensor model.
PLC: C200H-ID212
Sensor: E2EH-X7D1-T
E2EH
10
● Mounting
Tightening Force
Do not tighten the nut with excessive force.
Dimensions
Model Torque
M12 30 N·m
M18 70 N·m
M30 180 N·m
(Unit: mm)
Tolerance class IT16 applies to dimensions in this data sheet unless otherwise specified.
Pre-wired Models
(Shielded)
F
Mounting Hole
Dimensions
Dimensions M12 M18 M30
F (mm) 12.5 dia. 18.5 dia. 30.5 dia.
+0.5
0
+0.5
0
+0.5
0
Connector Models
(Shielded)
F
Mounting Hole
Dimensions
Dimensions M12 M18 M30
F (mm) 12.5 dia. 18.5 dia. 30.5 dia.
+0.5
0
+0.5
0
+0.5
0
E2EH-X3@@
*4-dia. 2-conductor heat-resistant PVC cable
(Conductor cross section: 0.3 mm2, insulator diameter: 1.3 mm),
Standard length: 2 m.
4-dia. 3-conductor heat-resistant PVC cable
(Conductor cross section: 0.3 mm2, insulator diameter: 1.3 mm),
Standard length: 2 m.
4
17
38
10
9
43
*
M12 × 1 Two clamping nuts
Indicator
E2EH-X3@@-M1@
4
17
38
10
53
M12 × 1
M12 × 1
Two clamping nuts
Indicator
24 4
38
10
12
43
M18 × 1 Two clamping nuts
Indicator *
*6-dia. 2-conductor heat-resistant PVC cable
(Conductor cross section: 0.5 mm2, insulator diameter: 1.9 mm),
Standard length: 2 m.
6-dia. 3-conductor heat-resistant PVC cable
(Conductor cross section: 0.5 mm2, insulator diameter: 1.9 mm),
Standard length: 2 m.
E2EH-X7@@ E2EH-X7@@-M1@
4
24
38
10
53
M18 × 1
Two clamping nuts
Indicator
M12 × 1
36 5
43
10
12
48
Indicator *
M30 × 1.5 Two clamping nuts
*6-dia. 2-conductor heat-resistant PVC cable
(Conductor cross section: 0.5 mm
2
, insulator diameter: 1.9 mm),
Standard length: 2 m.
6-dia. 3-conductor heat-resistant PVC cable
(Conductor cross section: 0.5 mm
2
, insulator diameter: 1.9 mm),
Standard length: 2 m.
E2EH-X12@@ E2EH-X12@@-M1@
5
36
43
10
58
M30 × 1.5 Two clamping nuts
M12 × 1
Indicator
Terms and Conditions of Sale
1. Offer; Acceptance. These terms and conditions (these "Terms") are deemed
part of all quotes, agreements, purchase orders, acknowledgments, price lists,
catalogs, manuals, brochures and other documents, whether electronic or in
writing, relating to the sale of products or services (collectively, the "Products")
by Omron Electronics LLC and its subsidiary companies (“Omron”). Omron
objects to any terms or conditions proposed in Buyer’s purchase order or other
documents which are inconsistent with, or in addition to, these Terms.
2. Prices; Payment Terms. All prices stated are current, subject to change with-
out notice by Omron. Omron reserves the right to increase or decrease prices
on any unshipped portions of outstanding orders. Payments for Products are
due net 30 days unless otherwise stated in the invoice.
3. Discounts. Cash discounts, if any, will apply only on the net amount of invoices
sent to Buyer after deducting transportation charges, taxes and duties, and will
be allowed only if (i) the invoice is paid according to Omron’s payment terms
and (ii) Buyer has no past due amounts.
4. Interest. Omron, at its option, may charge Buyer 1-1/2% interest per month or
the maximum legal rate, whichever is less, on any balance not paid within the
stated terms.
5. Orders. Omron will accept no order less than $200 net billing.
6. Governmental Approvals. Buyer shall be responsible for, and shall bear all
costs involved in, obtaining any government approvals required for the impor-
tation or sale of the Products.
7. Taxes. All taxes, duties and other governmental charges (other than general
real property and income taxes), including any interest or penalties thereon,
imposed directly or indirectly on Omron or required to be collected directly or
indirectly by Omron for the manufacture, production, sale, delivery, importa-
tion, consumption or use of the Products sold hereunder (including customs
duties and sales, excise, use, turnover and license taxes) shall be charged to
and remitted by Buyer to Omron.
8. Financial. If the financial position of Buyer at any time becomes unsatisfactory
to Omron, Omron reserves the right to stop shipments or require satisfactory
security or payment in advance. If Buyer fails to make payment or otherwise
comply with these Terms or any related agreement, Omron may (without liabil-
ity and in addition to other remedies) cancel any unshipped portion of Prod-
ucts sold hereunder and stop any Products in transit until Buyer pays all
amounts, including amounts payable hereunder, whether or not then due,
which are owing to it by Buyer. Buyer shall in any event remain liable for all
unpaid accounts.
9. Cancellation; Etc. Orders are not subject to rescheduling or cancellation
unless Buyer indemnifies Omron against all related costs or expenses.
10. Force Majeure. Omron shall not be liable for any delay or failure in delivery
resulting from causes beyond its control, including earthquakes, fires, floods,
strikes or other labor disputes, shortage of labor or materials, accidents to
machinery, acts of sabotage, riots, delay in or lack of transportation or the
requirements of any government authority.
11. Shipping; Delivery. Unless otherwise expressly agreed in writing by Omron:
a. Shipments shall be by a carrier selected by Omron; Omron will not drop ship
except in “break down” situations.
b. Such carrier shall act as the agent of Buyer and delivery to such carrier shall
constitute delivery to Buyer;
c. All sales and shipments of Products shall be FOB shipping point (unless oth-
erwise stated in writing by Omron), at which point title and risk of loss shall
pass from Omron to Buyer; provided that Omron shall retain a security inter-
est in the Products until the full purchase price is paid;
d. Delivery and shipping dates are estimates only; and
e. Omron will package Products as it deems proper for protection against nor-
mal handling and extra charges apply to special conditions.
12. Claims. Any claim by Buyer against Omron for shortage or damage to the
Products occurring before delivery to the carrier must be presented in writing
to Omron within 30 days of receipt of shipment and include the original trans-
portation bill signed by the carrier noting that the carrier received the Products
from Omron in the condition claimed.
13. Warranties. (a) Exclusive Warranty. Omron’s exclusive warranty is that the
Products will be free from defects in materials and workmanship for a period of
twelve months from the date of sale by Omron (or such other period expressed
in writing by Omron). Omron disclaims all other warranties, express or implied.
(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION,
EXPRESS OR IMPLIED, ABOUT NON-INFRINGEMENT, MERCHANTABIL-
ITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS.
BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE
PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR
INTENDED USE. Omron further disclaims all warranties and responsibility of
any type for claims or expenses based on infringement by the Products or oth-
erwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obli-
gation hereunder shall be, at Omron’s election, to (i) replace (in the form
originally shipped with Buyer responsible for labor charges for removal or
replacement thereof) the non-complying Product, (ii) repair the non-complying
Product, or (iii) repay or credit Buyer an amount equal to the purchase price of
the non-complying Product; provided that in no event shall Omron be responsi-
ble for warranty, repair, indemnity or any other claims or expenses regarding
the Products unless Omron’s analysis confirms that the Products were prop-
erly handled, stored, installed and maintained and not subject to contamina-
tion, abuse, misuse or inappropriate modification. Return of any Products by
Buyer must be approved in writing by Omron before shipment. Omron Compa-
nies shall not be liable for the suitability or unsuitability or the results from the
use of Products in combination with any electrical or electronic components,
circuits, system assemblies or any other materials or substances or environ-
ments. Any advice, recommendations or information given orally or in writing,
are not to be construed as an amendment or addition to the above warranty.
See http://www.omron247.com or contact your Omron representative for pub-
lished information.
14. Limitation on Liability; Etc. OMRON COMPANIES SHALL NOT BE LIABLE
FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,
LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY
WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS
BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.
Further, in no event shall liability of Omron Companies exceed the individual
price of the Product on which liability is asserted.
15. Indemnities. Buyer shall indemnify and hold harmless Omron Companies and
their employees from and against all liabilities, losses, claims, costs and
expenses (including attorney's fees and expenses) related to any claim, inves-
tigation, litigation or proceeding (whether or not Omron is a party) which arises
or is alleged to arise from Buyer's acts or omissions under these Terms or in
any way with respect to the Products. Without limiting the foregoing, Buyer (at
its own expense) shall indemnify and hold harmless Omron and defend or set-
tle any action brought against such Companies to the extent based on a claim
that any Product made to Buyer specifications infringed intellectual property
rights of another party.
16. Property; Confidentiality. Any intellectual property in the Products is the exclu-
sive property of Omron Companies and Buyer shall not attempt to duplicate it
in any way without the written permission of Omron. Notwithstanding any
charges to Buyer for engineering or tooling, all engineering and tooling shall
remain the exclusive property of Omron. All information and materials supplied
by Omron to Buyer relating to the Products are confidential and proprietary,
and Buyer shall limit distribution thereof to its trusted employees and strictly
prevent disclosure to any third party.
17. Export Controls. Buyer shall comply with all applicable laws, regulations and
licenses regarding (i) export of products or information; (iii) sale of products to
“forbidden” or other proscribed persons; and (ii) disclosure to non-citizens of
regulated technology or information.
18. Miscellaneous. (a) Waiver. No failure or delay by Omron in exercising any right
and no course of dealing between Buyer and Omron shall operate as a waiver
of rights by Omron. (b) Assignment. Buyer may not assign its rights hereunder
without Omron's written consent. (c) Law. These Terms are governed by the
law of the jurisdiction of the home office of the Omron company from which
Buyer is purchasing the Products (without regard to conflict of law princi-
ples). (d) Amendment. These Terms constitute the entire agreement between
Buyer and Omron relating to the Products, and no provision may be changed
or waived unless in writing signed by the parties. (e) Severability
. If any provi-
sion hereof is rendered ineffective or invalid, such provision shall not invalidate
any other provision. (f) Setoff. Buyer shall have no right to set off any amounts
against the amount owing in respect of this invoice. (g) Definitions. As used
herein, “including” means “including without limitation”; and “Omron Compa-
nies” (or similar words) mean Omron Corporation and any direct or indirect
subsidiary or affiliate thereof.
Certain Precautions on Specifications and Use
1. Suitability of Use. Omron Companies shall not be responsible for conformity
with any standards, codes or regulations which apply to the combination of the
Product in the Buyer’s application or use of the Product. At Buyer’s request,
Omron will provide applicable third party certification documents identifying
ratings and limitations of use which apply to the Product. This information by
itself is not sufficient for a complete determination of the suitability of the Prod-
uct in combination with the end product, machine, system, or other application
or use. Buyer shall be solely responsible for determining appropriateness of
the particular Product with respect to Buyer’s application, product or system.
Buyer shall take application responsibility in all cases but the following is a
non-exhaustive list of applications for which particular attention must be given:
(i) Outdoor use, uses involving potential chemical contamination or electrical
interference, or conditions or uses not described in this document.
(ii) Use in consumer products or any use in significant quantities.
(iii) Energy control systems, combustion systems, railroad systems, aviation
systems, medical equipment, amusement machines, vehicles, safety equip-
ment, and installations subject to separate industry or government regulations.
(iv) Systems, machines and equipment that could present a risk to life or prop-
erty. Please know and observe all prohibitions of use applicable to this Prod-
uct.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS
RISK TO LIFE OR PROPERTY OR IN LARGE QUANTITIES WITHOUT
ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO
ADDRESS THE RISKS, AND THAT THE OMRON’S PRODUCT IS PROP-
ERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE
OVERALL EQUIPMENT OR SYSTEM.
2. Programmable Products. Omron Companies shall not be responsible for the
user’s programming of a programmable Product, or any consequence thereof.
3. Performance Data. Data presented in Omron Company websites, catalogs
and other materials is provided as a guide for the user in determining suitabil-
ity and does not constitute a warranty. It may represent the result of Omron’s
test conditions, and the user must correlate it to actual application require-
ments. Actual performance is subject to the Omron’s Warranty and Limitations
of Liability.
4. Change in Specifications. Product specifications and accessories may be
changed at any time based on improvements and other reasons. It is our prac-
tice to change part numbers when published ratings or features are changed,
or when significant construction changes are made. However, some specifica-
tions of the Product may be changed without any notice. When in doubt, spe-
cial part numbers may be assigned to fix or establish key specifications for
your application. Please consult with your Omron’s representative at any time
to confirm actual specifications of purchased Product.
5. Errors and Omissions. Information presented by Omron Companies has been
checked and is believed to be accurate; however, no responsibility is assumed
for clerical, typographical or proofreading errors or omissions.
OMRON CANADA, INC. • HEAD OFFICE
Toronto, ON, Canada • 416.286.6465 • 866.986.6766 • www.omron247.com
OMRON ELECTRONICS DE MEXICO • HEAD OFFICE
México DF • 52.
55.59.01.43.00
• 001.800.556.6766 • mela@omron.com
OMRON ELECTRONICS DE MEXICO • SALES OFFICE
Apodaca, N.L. • 52.81.11.56.99.20 • 001.800.556.6766 • mela@omron.com
OMRON ELETRÔNICA DO BRASIL LTDA • HEAD OFFICE
São Paulo, SP, Brasil • 55.11.2101.6300 • www.omron.com.br
OMRON ARGENTINA • SALES OFFICE
Cono Sur • 54.11.4783.5300
OMRON CHILE • SALES OFFICE
Santiago • 56.9.9917.3920
OTHER OMRON LATIN AMERICA SALES
54.11.4783.5300
OMRON INDUSTRIAL AUTOMATION • THE AMERICAS HEADQUARTERS
Schaumburg, IL USA • 847.843.7900 • 800.556.6766 • www.omron247.com
OMRON EUROpE B.V. •
Wegalaan 67-69, NL-2132 JD, Hoofddorp, The Netherlands.
•
Tel: +31 (0) 23 568 13 00
Fax: +31 (0) 23 568 13 88
•
www.industrial.omron.eu
Cat. No. CSM_E2EH_DS_E_4_1 12/10 Note: Specifications are subject to change. © 2012 Omron Electronics LLC Printed in U.S.A.
