MT46V64M4FJ-75H - Micron Technology, Inc.

PRODUCTS AND SPECIFICATIONS DISCUSSED HER EIN ARE SUBJE CT TO CHANGE BY MICRON WITHOUT NOTICE.

09005aef8076894f

256Mb: x4, x8, x16

DDR SD RAM

DOUBLE DATA RATE

(DDR) SDRAM

MT46V64M4 – 16 MEG x 4 x 4 BANKS

MT46V32M8 – 8 MEG x 8 x 4 BANKS

MT46V16M16 – 4 MEG x 16 x 4 BANKS

For the latest data sheet revisions, please refer to the

Micronâ Web site: www.micron.com/datasheets

Features

•VDD = +2.5V ±0.2V, VDDQ = +2.5V ±0.2V

• Bidirectional data strobe (DQS) transmitted/received

with data, i.e., source-synchronous data capture (x16 has

two – one per byte)

• Internal, pipelined double da ta rate (DDR) archit ecture;

two data accesses per clock cycle

• Differe ntial clock inputs (CK and CK#)

• Commands entered on each positive CK edge

• DQS edge-aligned with data for READs; center-aligned

with data for WRITEs

• DLL to align DQ and DQS transitions with CK

• Four internal banks for concurrent operation

• Data mask (DM) for masking write data (x16 has two – one

per byte)

• Programmable burst lengths: 2, 4, or 8

• Auto Refresh and Self Refresh Modes

• Longer-lead TSOP for improved reliability (OCPL)

• 2.5V I/O (SSTL_2 compati ble)

• Concurrent auto precharge option supported

•tRAS lockout supported (tRAP = tRCD)

NOTE: 1. Contact Micron for availability of le ad-free products.

2. Supports PC27 00 modules with 2.5-3-3 timing.

3. Supports PC21 00 modules with 2-2-2 timing.

4. Supports PC21 00 modules with 2-3-3 timing.

5. Supports PC21 00 modules with 2.5-3-3 timing.

6. Supports PC16 00 modules with 2-2-2 timing.

7. CL=CAS(READ) latency.

8. Minimum clock rate @ CL = 2 (-75E, -75Z), @ CL = 2.5

(-6T, -6R, -75)

OPTIONS

MARKING

• Configuration

64 Meg x 4 (16 Meg x 4 x 4 banks) 64M4

32 Meg x 8 (8 Meg x 8 x 4 banks) 32M8

16 Meg x 16 (4 Meg x 16 x 4 banks) 16M16

• Plastic Package – OCPL

66-pin TSOP TG

66-pin TSOP (lead-free)

•Plastic Package

60-Ball FBGA (16mm x 9mm) FJ

60-Ball FBGA (16mm x 9mm)(lead-free)1BJ

60-Ball FBGA (14mm x 8mm) FG

60-Ball FBGA (14mm x 8mm) (lead-free)1BG

• Timing – Cycle Time

6ns @ CL = 2.5 (DDR333) 2 (FBGA only) -6

6ns @ CL = 2.5 (DDR333) 2 (TSOP only) -6R/-6T

7.5ns @ CL = 2 (DDR266)3 -75E

7.5ns @ CL = 2 (DDR266A)4-75Z

7.5ns @ CL = 2.5 (DDR266B)5, 6 -75

• Self Refresh

Standard None

Low-Power Self Refresh L

• High-Speed Process Enhancement

Standard None

High Speed H

• Temperature Ra ting

Standard (0°C to +70°C) None

Industrial Temperature (-40°C to +85°C) IT

Table 1: Key Timing Parameters

SPEED

GRADE

CLOCK RATE

DATA-OUT

WINDOW

ACCESS

WINDOW

DQS–DQ

SKEWCL=2 CL=2.5

-6 133 MHz 167 MHz 2.1ns ±0.7ns +0.40ns

-6R/-6T 133 MHz 167 MHz 2.0ns ±0.7ns +0.45ns

-75E/-75Z 133 MHz 133 MHz 2.5ns ±0.75ns +0.5ns

-75 100 MHz 133 MHz 2.5ns ±0.75ns +0.5ns

64 MEG x 4 32 MEG x 8 16 MEG x 16

Configuration 16 Meg x 4 x 4

banks 8 Meg x 8 x 4

banks 4 Meg x 16 x 4

banks

Refresh Count 8K 8K 8K

Row Addressing 8K (A0–A12) 8K (A0–A12) 8K (A0–A12)

Bank Addressing 4 (BA0,BA1) 4 (BA0,BA1) 4 (BA0,BA1)

Column Addressing 2K (A0–A9,A11) 1K (A0–A9) 512 (A0–A8)

VSS

DQ15

VSSQ

DQ14

DQ13

VDDQ

DQ12

DQ11

VSSQ

DQ10

DQ9

VDDQ

DQ8

VSSQ

UDQS

DNU

VREF

VSS

UDM

CK#

CKE

A12

A11

VSS

x16

VDD

DQ0

VDDQ

DQ1

DQ2

VssQ

DQ3

DQ4

VDDQ

DQ5

DQ6

VssQ

DQ7

VDDQ

LDQS

VDD

DNU

LDM

WE#

CAS#

RAS#

CS#

BA0

BA1

A10/AP

VDD

x16 VSS

DQ7

VSSQ

DQ6

VDDQ

DQ5

VSSQ

DQ4

VDDQ

VSSQ

DQS

DNU

VREF

VSS

CK#

CKE

A12

A11

VSS

x8 x4

VSS

VSSQ

DQ3

VDDQ

VSSQ

DQ2

VDDQ

VSSQ

DQS

DNU

VREF

VSS

CK#

CKE

A12

A11

VSS

VDD

DQ0

VDDQ

DQ1

VSSQ

DQ2

VDDQ

DQ3

VSSQ

VDDQ

VDD

DNU

WE#

CAS#

RAS#

CS#

BA0

BA1

A10/AP

VDD

x8x4

VDD

VDDQ

DQ0

VSSQ

VDDQ

DQ1

VSSQ

VDDQ

VDD

DNU

WE#

CAS#

RAS#

CS#

BA0

BA1

A10/AP

VDD

Figure 1: Pin Assignment (Top View)

66-Pin TSOP

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

Figure 2: 256Mb DDR SDRAM Part

Numbers

General D e scrip tion

The 256Mb DDR SDRAM is a high-speed CMOS,

dynamic random-access memory containing

268,435,456 bits. It is internally configured as a quad-

bank DRAM.

The 256Mb DDR SDRAM uses a double-data-rate

architecture to achieve high-speed operation. The

double data rate architecture is essentially a 2n-

prefetch architecture with an interface designed to

transfer two data words per clock cycle at the I/O pins.

A single read or write access for the 256Mb DDR

SDRAM effectively consists of a single 2n-bit wide,

one-clock-cycle data transfer at the internal DRAM

core and two corresponding n-bit wide, one-half-

clock-cycle data transf ers at the I/O p i ns.

A bidirectional data strobe (DQS) is transmitted

externally, along with data, for use in data capture at

the receiver. DQS is a strobe transmitted by the DDR

SDRAM during READs and by the memory controller

during WRITEs. DQS is edge-aligned with data for

READs and center-aligned with data for WRITEs. The

x16 offering has two data strobes, one for the lower

byte and o ne for the upper byte.

The 256Mb DDR SDRAM operates from a differen-

tial clock (CK and CK#); the crossing of CK going HIGH

and CK# going LOW will be referred to as the positive

edge of CK. Commands (address and control signals)

are registered at every positive edge of CK. Input data

is registered on both edges of DQS, and output data is

referenced to both edges of DQS, as well as to both

edges of CK.

Read and write accesses to the DDR SDRAM are

burst o riente d; acces ses st art at a select ed loc atio n and

continue for a programmed number of locations in a

programmed se quence. Accesses begin with the regis-

tration of an ACTIVE command, which is then fol-

lowed by a READ or WRITE command. The address

bits registered coincident with the ACTIVE command

ar e u s ed t o s el ect t he bank and r ow to be accesse d. Th e

address bits registered coincident with the READ or

WRITE command are used to select the bank and the

starting column location for the burst access.

The D DR SDRAM provides for programmable READ

or WRITE burst lengths of 2, 4, or 8 locations. An auto

precharge function may be enabled to provide a self-

timed row precharge that is initiated at the end of the

burst access.

As with standard SDR SDRAMs, the pipelined,

multibank architecture of DDR SDRAMs allows for

concurrent operation, thereby effectively providing

high bandwidth by hiding row precharge and activa-

tion time.

An auto refresh mode is provided, along with a

power-saving power-down mode. All inputs are com-

patible with the JEDEC standard for SSTL_2. All full

drive option outputs are SSTL_2, Class II-compatible.

NOTE: 1. The functionality and the timing specifica-

tions discussed in this data sheet are for the

DLL-enabled mode of operation.

2. Throughout the data sheet, the various fig-

ures and text refer to DQs as “DQ.” The DQ

term is to be interpreted as any and all DQ

collecti vely, unl ess specifica lly stated othe r-

wise. Additionally, the x16 is divided into

two bytes, the lower byte and upper byte.

For the lower byte (DQ0 through DQ7) DM

refers to LDM and DQS refers to LDQS. For

the upper byte (DQ8 through DQ15) DM

refers to UDM and DQS refers to UDQS.

3. Complete functionality is described

throughout the document and any page or

diagram may have been simplified to con-

vey a topic and may not be inclusive of all

requirements.

4. Any specific requirement takes precedence

over a general statement.

Special Options

Standard

Low Power

High-Speed Process

ConfigurationMT46V Package Speed

Special

Options

Temperature

Configuration

64 Meg x 4

32 Meg x 8

16 Meg x 16

64M4

32M8

16M16

Package

400-mil TSOP

400-mil TSOP (lead-free)

16x9 FBGA

16x9 FBGA (lead-free)

14x9 FBGA

14x9 FBGA (lead-free)

Speed Grade

tCK = 6ns, CL = 2.5

tCK = 7.5ns, CL = 2

tCK = 7.5ns, CL = 2.5

-6

-6T

-6R

-75E

-75Z

-75

Operating Temp

Standard

Industrial Temp

Example Part Number: MT46V16M16TG-75Z H

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

Table of Contents

Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Register Definition. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Mode Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Burst Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Burst Type. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Read Latency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Operating Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Extended Mode Reg ist er. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Output Drive Streng th . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

DLL Enable/Disable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

DESELECT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

NO OPERATION (NOP). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

LOAD MODE REGISTER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

ACTIVE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

READ. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

WRITE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

PRECHARGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Auto Precharge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

BURST TERMINATE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

AUTO REFRESH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

SELF REFRESH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Bank/Row Activation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

READs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

WRITEs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

PRECHARGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

Power-Down (CKE Not Active) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

Absolute Maxi mum Rati ngs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59

Data Sheet Designation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

List of Figu res

Figure 1: Pin Assignment (Top View) 66-Pin TSOP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Figure 2: 256Mb DDR SDRAM Part Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Figure 3: Functional Block Diagram: 64 M eg x 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Figure 4: Functional Block Diagram: 32 M eg x 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Figure 5: Functional Block Diagram: 16 M eg x 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Figure 6: 60-Ball FBGA Ball Assignment (Top View) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Figure 7: Mode Register Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Figure 8: CAS Latency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Figure 9: Extended Mode Register Definit ion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Figure 10: Activating a Specific Row in a Specific Bank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Figure 11: Example: Meeting tRCD (tRRD) MIN When 2 < tRCD (tRRD) MIN/tCK £ 3. . . . . . . . . . . . . . . . . . . . . .19

Figure 12: READ Command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Figure 13: READ Burst. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Figure 14: Consecutive READ Bursts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Figure 15: Nonconsecutive READ Bursts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Figure 16: Random READ Accesses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Figure 17: Terminating a READ Burst . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Figure 18: READ to WRITE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Figure 19: READ to PRECHARGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Figure 20: WRITE Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Figure 21: WRITE Burst. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

Figure 22: Consecutive WRITE to WRITE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

Figure 23: Nonconsecutive WR ITE to WRITE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Figure 24: Random WRITE Cycles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

Figure 25: WRITE to READ - Uninterrupting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

Figure 26: WRITE to READ – Interrupting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

Figure 27: WRITE to READ – Odd Number of Data, Interrupt ing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

Figure 28: WRITE to PRECHA RGE - Uni nte rrupting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

Figure 29: WRITE to PRECHA RGE – In terr upting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

Figure 30: WRITE to PRECHARGE – Odd Number of Data – Interrupt ing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

Figure 31: PRECHARGE Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

Figure 32: Power-Down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

Figure 33: Input Voltage Wavefor m. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47

Figure 34: SSTL_2 Clock Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48

Figure 35: Derating Data Valid Window (tQH - tDQSQ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60

Figure 36: Full Drive Pull-Down Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61

Figure 37: Full Drive Pull-Up Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61

Figure 38: Reduced Drive Pull-Down Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62

Figure 39: Reduced Drive Pull-Up Charact e ristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62

Figure 40: x4, x8 Data Output Timing – tDQSQ, tQH, and Data Valid Window . . . . . . . . . . . . . . . . . . . . . . . . . . . .65

Figure 4 1 : x1 6 Data Output Timing – tDQSQ, tQ H, a nd Data Valid Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66

Figure 42: Data Output Timing – tAC and tDQSCK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67

Figure 43: Data Input Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68

Figure 44: Initialize and Load Mode Regis ters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69

Figure 45: Power-Down Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70

Figure 46: Auto Refresh Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71

Figure 47: Self Refresh Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72

Figure 48: Bank Read - Without Auto Precharge. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73

Figure 49: Bank Read - With Auto Precha rge. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74

Figure 50: Bank Write - Without Auto Precharge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75

Figure 51: Bank Write - With Auto Prech arge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76

Figure 52: Write – DM Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77

Figure 53: 66-Pin Plastic TSO P (4 00 mi l). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78

Figure 54: 60-Ball FBGA (16 x 9mm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79

Figure 55: 60-Ball FBGA (14 x 8mm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

List of Ta bles

Table 1: Key Timing Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Table 2: Ball/Pin Descript ions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Table 3: Reserved NC Balls and Pins1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Table 4: Burst Definition. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Table 5: CAS Latency (CL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Table 6: Truth Table – Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Table 7: Truth Table – DM Opera ti o n . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Table 8: Truth Table – CKE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

Table 9: Truth Table – Current State Bank n – Command to Bank n . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42

Table 10: Truth Table – Current State Bank n– Command to Bank m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44

Table 11: DC Electrical Characteristics and Operat ing Conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

Table 12: AC Input Operating Conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

Table 13: Clock Input Opera ti ng Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48

Table 14: Capacitance (x4, x8 TSOP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49

Table 15: Capacitance (x4, x8 FBGA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49

Table 16: Capacitance (x16 TSOP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50

Table 17: Capacitance (x16 FBGA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50

Table 18: IDD Specifications and Conditions (x4, x8; -6/-6R/-6T/- 75E). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

Table 19: IDD Specifications and Condit ions (x4, x8; -75Z/-75). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52

Table 20: IDD Specifications and Condit ions (x16; -6/-6R/-6T/-75E). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53

Table 21: IDD Specifications and Condit ions (x16; -75Z/-75). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54

Table 22: IDD Test Cycle Times . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55

Table 23: Electrical Charact e ristics and Recommended AC Operatin g Condit ions (-6/-6T/-6R/-75E) . . . . . .56

Table 24: Electrical Characteristics and Recommended AC Operating Conditions (-75Z/-75) . . . . . . . . . . . . .57

Table 25: Input Slew Rate Derating Values for Addresses and Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58

Table 26: Input Slew Rate Derating Values for DQ, DQ S, and DM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58

Table 27: Normal Output Drive Chara ct e ristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63

Table 28: Reduced Output Drive Charac ter ist ics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

Figur e 3: Functional Block Diagram: 64 Meg x 4

RAS#

CAS#

ROW-

ADDRESS

MUX

CS#

WE#

CK#

CONTROL

LOGIC

COLUMN-

ADDRESS

COUNTER/

LATCH

MODE REGISTERS

COMMAND

DECODE

A0-A12,

BA0, BA1

CKE

ADDRESS

1024

(x8)

8192

I/O GATING

DM MASK LOGIC

COLUMN

DECODER

BANK0

MEMORY

ARRAY

(8,192 x 1,024 x 8)

BANK0

ROW-

ADDRESS

LATCH

DECODER

8192

SENSE AMPLIFIERS

BANK

CONTROL

LOGIC

BANK1BANK2 BANK3

REFRESH

COUNTER

INPUT

REGISTERS

RCVRS

clk

out

DATA

DQS

MASK

DATA

COL0

clk

DRVRS

DLL

MUX

DQS

GENERATOR

DQ0–

DQ3

DQS

READ

LATCH

WRITE

FIFO

DRIVERS

COL0

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

Figur e 4: Functional Block Diagram: 32 Meg x 8

RAS#

CAS#

ROW-

ADDRESS

MUX

CS#

WE#

CK#

CONTROL

LOGIC

COLUMN-

ADDRESS

COUNTER/

LATCH

MODE REGISTERS

COMMAND

DECODE

A0-A12,

BA0, BA1

CKE

ADDRESS

512

(x16)

8192

I/O GATING

DM MASK LOGIC

COLUMN

DECODER

BANK0

MEMORY

ARRAY

(8192 x 512 x 16)

BANK0

ROW-

ADDRESS

LATCH

DECODER

8192

SENSE AMPLIFIERS

BANK

CONTROL

LOGIC

BANK1BANK2 BANK3

REFRESH

COUNTER

INPUT

REGISTERS

RCVRS

clk

out

DATA

DQS

MASK

DATA

clk

DRVRS

DLL

MUX

DQS

GENERATOR

DQ0–

DQ7

DQS

READ

LATCH

WRITE

FIFO

DRIVERS

COL0

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

Figure 5: Functional Block Diagram: 16 Meg x 16

RAS#

CAS#

ROW-

ADDRESS

MUX

CS#

WE#

CK#

CONTROL

LOGIC

COLUMN-

ADDRESS

COUNTER/

LATCH

MODE REGISTERS

COMMAND

DECODE

A0-A12,

BA0, BA1

CKE

ADDRESS

256

(x32)

8192

I/O GATING

DM MASK LOGIC

COLUMN

DECODER

BANK0

MEMORY

ARRAY

(8,192 x 256 x 32)

BANK0

ROW-

ADDRESS

LATCH

DECODER

8192

SENSE AMPLIFIERS

BANK

CONTROL

LOGIC

BANK1BANK2 BANK3

REFRESH

COUNTER

INPUT

REGISTERS

RCVRS

clk

out

DATA

DQS

MASK

DATA

clk

DRVRS

DLL

MUX

DQS

GENERATOR

16 16

DQ0 -

DQ15

LDQS

UDQS

READ

LATCH

WRITE

FIFO

DRIVERS

COL0

LDM,

UDM

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

Table 2: Ball/Pin Descriptions

FBGA

NUMBERS TSOP

NUMBERS SYMBOL TYPE DESCRIPTION

G2, G3 45, 46 CK, CK# Input Clock: CK and CK# are differential clock inputs. All address and

control input signals are sampled on the crossing of the positive

edge of CK and the negative edge of CK#. Output data (DQ and

DQS) is referenced to the crossings of CK and CK#.

H3 44 CKE Input Clock Enable: CKE HIGH activates and CKE LOW deactivates the

internal clock, input buffers, and output drivers. Taking CKE LOW

provides PRE CHARGE POWER-DOWN and SELF REFRESH ope rations

(all banks i dle) or ACTIVE P OWER-DOWN (row ACTIVE i n any bank ).

CKE is synchronous for POWER-DOWN entry and exit and for SELF

REFRESH entry. CKE is asynchronous for SELF REFRESH exit and for

disabling the outputs. CKE must be maintained HIGH throughout

read and write accesses. Input buf fers (excluding CK, CK#, and CKE)

are disabled during POWER- DOWN. Input buffers (excluding CKE)

are disabled during SELF REFRESH. CKE is an SSTL_2 input but will

detect an LVCMO S LOW level after VDD is applied and until CKE is

first brought HIGH, after which it becomes an SSTL_2 input only.

H8 24 CS# Input Chip Select: CS# enables (registered LOW) and disables (registered

HIGH) the command decoder. All commands are masked when CS#

is registered HIGH. CS# provides for external bank selection on

systems with multiple banks. CS# is considered part of the

command code.

H7, G8, G7 23, 22, 21 RAS#, CAS#,

WE# Input Command Inputs: RAS#, CAS#, and WE# (along with CS#) define

the command being entered.

3F 47 DM Input Input Data Mask: DM is an input mask signal for write data. Input

data is masked when DM is sampled HIGH along with that input

data during a WRITE access. DM is sampled on both edges of DQS.

Although DM pins are input-only, the DM loading is designed to

match that of DQ and DQS pins. For the x16, LDM is DM for DQ0–

DQ7 and UDM is DM for DQ8–DQ15. Pin 20 is a NC on x4 and x8.

F7, 3F 20, 47 LDM, UDM

J8, J7 26, 27 BA0, BA1 Input Bank Address Inputs: BA0 and BA1 define to which bank an

ACTIVE, READ, WRITE, or PRECHARGE command is being applied.

K7, L8, L7,

M8, M2, L3,

L2, K3, K2, J3,

K8,

J2, H2

29, 30, 31, 3 2,

35, 36, 37, 3 8,

39, 40, 28

41, 42

A0, A1, A2,

A3, A4, A5,

A6, A7, A8,

A9, A10, A11,

A12

Input Address Inputs: Provid e the row address for ACTIVE comm ands, and

the column address and auto precharge bit (A10) for READ/WRITE

commands, to select one location out of the memory array in the

respective bank. A10 sampled during a PRECHARGE command

determines whether the PRECHARGE applies to one bank (A10

LOW, bank selected by BA0, BA1) or all banks (A10 HIGH). The

address inputs also provide the op-code during a MODE REGISTER

SET command. BA0 and BA1 define which mode register (mode

MODE REGISTER command.

A8, B9, B 7,

C9, C7, D9,

D7, E9, E1,

D3, D1, C3,

C1, B3, B1, A2

2, 4, 5,

7, 8, 10,

11, 13, 54, 5 6,

57, 59, 60, 6 2,

63,

DQ0–DQ2

DQ3–DQ5

DQ6–DQ8

DQ9–DQ11

DQ12–DQ14

DQ15

I/O Data Input/Output: Data bus for x16.

(DQ4–DQ15 are NC for the x4)

(DQ8–DQ16 are NC for the x8)

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

NOTE:

1. NC pins not listed may also be reserved for other uses now or in the future. This table simply defines specific NC pins

deemed to be of importance.

A8, B7, C 7,

D7, D3, C3,

B3, A2

2, 5, 8,

11, 56, 59, 6 2,

DQ0–DQ2

DQ3–DQ5

DQ6, DQ7

I/O Data Input/Output: Data bus for x8.

(DQ4–DQ7 are NC for the x4)

B7, D7, D3,

B3 5, 11, 56,

62 DQ0–DQ2

DQ3 I/O Data Input/Output: Data bus for x4.

DQS

LDQS

UDQS

I/O Data Strobe: Output with read data, input with write data. DQS is

edge-aligned with read data, centered in write data. It is used to

capture data. For the x16, LDQS is DQS for DQ0–DQ7 and UDQS is

DQS for DQ8–DQ15. Pin 16 (E7) is NC on x4 and x8.

14, 17, 25, 4 3,

53 NC – No Connect: These pins should be left unconnected.

F9 19, 50 DNU –Do Not Use: Must fl oat to minimize noise on VREF.

B2, D2, C8,

E8, A9 3, 9, 15, 55,

61 VDDQSupply DQ Power Supply: +2.5V ±0.2V. Isolated on the die for improved

noise immunity.

A1, C2, E 2,

B8, D8 6, 12, 52, 58,

64 VSSQSupply DQ Ground: Isolated on the die for improved noise immunity.

F8, M7, A7 1, 18, 33 VDD Supply Power Supply: +2.5V ±0.2V.

A3, F2, M3 34, 48, 66 VSS Supply Ground.

F1 49 VREF Supply SSTL_2 reference voltage.

Table 2: Ball/Pi n D e scrip tions (Conti nued)

FBGA

NUMBERS TSOP

NUMBERS SYMBOL TYPE DESCRIPTION

Table 3: Reserved NC Balls and Pins1

FBGA

NUMBERS TSOP

NUMBERS SYMBOL TYPE DESCRIPTION

F9 17 A13 I Address input A13 for 1Gb devices. DNU for FBGA.

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

Figur e 6: 60-Ball FBGA Ball Assignment (Top V iew)

DQ14

DQ12

DQ10

DQ8

REF

DQ15

A12

A11

DQ13

DQ11

DQ9

UDQS

UDM

CK#

CKE

DQ2

DQ4

DQ6

LDQS

LDM

WE#

RAS#

BA1

DQ0

CAS#

CS#

BA0

A10

DQ1

DQ3

DQ5

DQ7

DNU

x16 (Top View)

REF

A12

A11

DQ3

DQ2

DQS

CK#

CKE

DQ0

DQ1

WE#

RAS#

BA1

CAS#

CS#

BA0

A10

DNU

x4 (Top View)

REF

DQ7

A12

A11

DQ6

DQ5

DQ4

DQS

CK#

CKE

DQ1

DQ2

DQ3

WE#

RAS#

BA1

DQ0

CAS#

CS#

BA0

A10

DNU

x8 (Top View)

123456789

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

Functio n a l D e scrip tion

The 256Mb DDR SDRAM is a high-speed CMOS,

dynamic random-access memory containing

268,435,456 bits. The 256Mb DDR SDRAM is intern ally

conf ig u red as a quad-bank DRAM .

The 256Mb DDR SDRAM uses a double data rate

architecture to achieve high-speed operation. The

double data rate architecture is essentially a 2n-

prefetch architecture, with an interface designed to

transfer two data words per clock cycle at the I/O pins.

A single read or write access for the 256Mb DDR

SDRAM consists of a single 2n-bit wide, one-clock-

cycle data transfer at the internal DRAM core and two

corresponding n-bit wide, one-half-clock-cycle data

transfers at the I/O pins.

Read and write accesses to the DDR SDRAM are

burst oriented; access es start at a selected locat ion and

continue for a programmed number of locations in a

programmed sequ ence. Accesses begin with the regis-

tration of an ACTIVE command, which is then fol-

lowed by a READ or WRITE command. The address

bits registered coincident with the ACTIVE command

are used to select the bank and row to be accessed

(BA0, BA1 select the bank; A0–A12 select the row). The

address bits registered coincident with the READ or

WRITE command are used to select the starting col-

umn lo cation for the burst access.

Prior to normal operation, the DDR SDRAM must

be initialized. The following sections provide detailed

information covering device initialization, register def-

inition, command descriptions, and device operation.

Initialization

DDR SDRAMs must be powered up and initialized

in a predefined manner. Operational procedures other

than those specified may result in undefined opera-

tion. Power must first be applied to VDD and VDDQ

simultaneously, and then to VREF (and to the system

VTT). VTT must be applied after VDDQ to avoid device

latch-up, which may cause permanent damage to the

device. VREF can be applied any time after VDDQ but is

expected to be nominally coincident with VTT. Except

for CKE, inputs are not recognized as valid until after

VREF is applied. CKE is an SSTL_2 input but will detect

an LVCMOS LOW level after VDD is applied. After CKE

pass es through VIH, it will transition to a SSTL_2 signal

and remain as such u ntil power is cycle d. Maintain ing

an LVCMOS LOW level on CKE during power-up is

required to ensure that the DQ and DQS outputs will

be in the High-Z state, where they will remain until

driven in nor mal ope ration (by a read acces s). Afte r all

power supply and reference voltages are stable, and

the clock is stable, the DDR SDRAM requires a 200µs

delay prior to applying an executable command.

Once the 200µs delay has been satisfied, a DESE-

LECT or NOP command should be applied and CKE

should be brought HIGH. Following the NOP com-

mand, a PRECHARGE ALL command should be

applied. Next a LOAD MODE REGISTER command

should be issued for the extended mode register (BA1

LOW and BA0 HIGH) to enable the DLL, followed by

another LOAD MODE REGISTER command to the

mode register (BA0/BA1 both LOW) to reset the DLL

and to program the operating parameters. Two hun-

dred clock cycles are required between the DLL reset

and any READ command. A PRECHARGE ALL com-

mand should then be applied, placing the device in the

all banks idle st ate.

Once in the idle state, two AUTO REFRESH cycles

must be performed (tRFC must be satisfied). Addition-

ally, a LO AD MODE REGISTER comma nd f or th e mode

gram operating parameters without resetting the DLL)

is required. Following these requirements, the DDR

SDRAM is ready for normal operation.

Mode Register

The mode register is used to define the specific

mode of opera tion of the DDR SDRAM. This definition

include s the se lection of a burs t length , a burst type, a

CAS latency, and an operating mode, as shown in

Figure 7 on p age 13 . The mode register is programmed

via the MODE REGISTER SET command (with BA0 = 0

and BA1 = 0) and will retain the stored information

until it is programm ed again or the device loses p ower

(except for bit A 8, wh ich is self-clearing).

Reprogramming the mode register will not alter the

contents of the memory, provided it is performed cor-

rectly. The mode register must be loaded (reloaded)

when all banks are idle and no bursts are in progress,

and the controller must wait the specified time before

initiating the subsequent operation. Violating either of

these requirements will result in unspecified opera-

tion.

Mode register bits A0–A2 specify the burst length;

A3 specifies the type of burst (sequential or inter-

leaved); A4–A6 specify the CAS latency; and A7–A12

specify the operating mode.

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

Burst Length

Read and write accesses to the DDR SDRAM are

burst oriented, with the burst length being program-

mable, as shown in Figure 7. The burst length deter-

mines the maximum number of column locations that

can be accessed for a given READ or WRITE command.

Burst lengths of 2, 4, or 8 locations are available for

both the sequential an d the in terleaved burst ty pes.

Reserved states should not be used, as unknown

operation or incompatibility with future versions may

result.

When a READ or WRITE command is issued, a block

of columns equal to the burst length is effectively

selected. All accesses for that burst take place within

this block, meaning that the burst will wrap within the

block if a boundary is reached. The block is uniquely

selected by A1–Ai when the burst length is set to two,

by A2–Ai when the burst length is set to four, and by

A3-Ai when the burst length is set to eight (where Ai is

the most significant column address bit for a given

configuration). The remaining (least significant)

address bit(s) is (are) used to select the starting loca-

tion within the block. The programmed burst length

applies to both READ and WRITE bursts.

Burs t Type

Accesses within a given burst may be programmed

to be either sequent ia l or inter l eav ed; this is r ef er red to

as the burst type and is selected via bit M3.

The ordering of accesses within a burst is deter-

mined by the burst length, the burst type, and the

starting column address, as shown in Table4, Burst

Definition, on p age 14.

Figure 7: Mode Register Definit ion

Operating Mode

Normal Operation

Normal Operation/Reset DLL

All other states reserved

Valid

Burst Type

Sequential

Interleaved

CAS Latency

Reserved

2.5

Reserved

Burst LengthCAS Latency BT0*

A9 A7 A6 A5 A4 A3A8 A2 A1 A0

Mode Register (Mx)

Address Bus

976543

8210

M6-M0

M8 M7

Operating Mode

A10A12 A11BA0BA1

* M14 and M13 (BA1 and BA0)

must be “0, 0” to select the

base mode register (vs. the

extended mode register).

M9M10M12 M11

Burst Length

Reserved

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

NOTE:

1. Whenever a boundary of the block is reached within a

given sequence above, the following access wraps

within the block.

2. For a burst length of two, A1–Ai select the two-data-

element block; A0 selects the first access within the

block.

3. For a burst length of four, A2–Ai select the four-data-

element block; A0–A1 select the first access within the

block.

4. For a burst length of eight, A3–Ai select the eight-data-

element block; A0–A2 select the first access within the

block.

Read Latency

The READ latency is the delay, in clock cycles,

between the registration of a READ command and the

availability of the first bit of output data. The latency

can be set to 2 or 2.5 clocks, as shown in Figure 8.

If a READ command is registered at clock edge n,

and the latency is m clocks, the data will be available

nominally coincident with clock edge n + m. Table 5,

CAS Latency (CL), on page 14 indicates the operating

frequencies at which each CAS latency setting can be

used.

Reserved states should not be used, as unknown

operation or incompatibility with future versions may

result.

Figure 8: CAS Latency

Operating Mode

The nor mal operatin g mode is s elected by issuin g a

MODE REGISTER SET command with bits A7–A12

each set to zero, and bits A0–A6 set to the desired val-

ues. A DLL reset is ini tiat ed by issuing a MO D E REGIS-

TER SET command with bits A7 and A9–A12 each set

to zero, bit A8 set to one, and bits A0–A6 set to the

desired values. Although not required by the Micron

device, JEDEC specifications recommend when a

LOAD MODE REGISTER command is issued to reset

the DLL, it should always be followed by a LOAD

MODE REGISTER command to select normal operat-

ing mode.

Table 4: Burst Definition

BURST

LENGTH

STARTING

COLUMN

ADDRESS

ORDER OF ACCESSES

WITHIN A BURST

TYPE=

SEQUENTIAL TYPE=

INTERLEAVED

2A0

00-1 0-1

11-0 1-0

4A1A0

0 0 0-1-2-3 0-1-2-3

0 1 1-2-3-0 1-0-3-2

1 0 2-3-0-1 2-3-0-1

1 1 3-0-1-2 3-2-1-0

8A2A1A0

0 0 0 0-1-2-3-4-5-6-7 0-1-2-3-4-5-6-7

0 0 1 1-2-3-4-5-6-7-0 1-0-3-2-5-4-7-6

0 1 0 2-3-4-5-6-7-0-1 2-3-0-1-6-7-4-5

0 1 1 3-4-5-6-7-0-1-2 3-2-1-0-7-6-5-4

1 0 0 4-5-6-7-0-1-2-3 4-5-6-7-0-1-2-3

1 0 1 5-6-7-0-1-2-3-4 5-4-7-6-1-0-3-2

1 1 0 6-7-0-1-2-3-4-5 6-7-4-5-2-3-0-1

1 1 1 7-0-1-2-3-4-5-6 7-6-5-4-3-2-1-0

Table 5: CAS Latency (CL)

SPEED

ALLOWABLE OPERATING

CLOCK FREQUENCY (MHz)

CL = 2 CL = 2.5

-6/-6R/-6T 75 £ f £ 133 75 £ f £ 167

-75E 75 £ f £ 133 75 £ f £ 133

-75Z 75 £ f £ 133 75 £ f £ 133

-75 75 £ f £ 100 75 £ f £ 133

CK#

COMMAND

DQS

CL = 2

READ NOP NOP NOP

Burst Length = 4 in the cases shown

Shown with nominal tAC, tDQSCK, and tDQSQ

CK#

COMMAND

DQS

CL = 2.5

T0 T1 T2 T2n T3 T3n

DON’T CARETRANSITIONING DATA

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

All other combinations of values for A7–A12 are

reserved for future use and/or test modes. Test modes

and reserved states should not be used, as unknown

operation or incompatibility with future versions may

result.

Extended Mode Register

The extended mode register controls functions

beyond those controlled by the mode register; these

additional functions are DLL enable/disable and out-

put drive strength. These functions are controlled via

the bits shown in Figur e9. The extended mode register

is programmed via the LOAD MODE REGISTER com-

mand to the mode register (with BA0 = 1 and BA1 = 0)

and will retain the stored information until it is pro-

grammed again or the device loses power. The

enabling of the DLL should always be followed by a

LOAD MODE REGISTER command to the mode regis-

ter (BA0/BA1 both LOW) to reset the DLL.

The extended mode register must be loaded when

all banks are idle and no bursts are in progress, and the

controller must wait the specified time before initiat-

ing any subsequent operation. Violating either of these

requirements could result in unspecified operation.

Output Drive Strength

The normal drive strength for all outputs are speci-

fied to be SSTL_2, Class II. The x16 supports a pro-

grammable option for reduced drive. This option is

intended for the support of the lighter load and/or

point-to-point environments. The selection of the

reduced drive strength will alter the DQ pins and DQS

pins from SSTL_2, Class II drive strength to a reduced

drive strength, which is approximately 54 percent of

the SSTL_2, Class II drive str eng th .

DLL Enable/Disable

When the part is running without the DLL enabled,

device functionality may be altered. The DLL must be

enabled for normal operation. DLL enable is required

during power-up initialization and upon returning to

normal operation after havi ng di sa bled the DLL fo r th e

purpose of debug or evaluation. (When the device

exits self refresh mode, the DLL is enabled automati-

cally.) Any time the DLL is enabled, 200 clock cycles

must occur before a READ command can be issued.

Figure 9: Extended Mode Register

Definition

NOTE:

1. E14 and E13 (BA1 and BA0) must be “0, 1” to select the

extended mode register vs. the base mode register.

2. The reduced drive strength option is not supported on

the x4 and x8 versions; it is only available on the x16

version.

3. The QFC# option is not supported.

Operating Mode

Reserved

–

–Valid

–

DLL

Enable

Disable

DLL

A9 A7 A6 A5 A4 A3A8 A2 A1 A0

Extended Mode

Address Bus

976543

8210

Drive Strength

Normal

Reduced

E1,

Operating Mode

A10A11

A12

BA1BA0

1314

E3E4

–

–0

–

E6 E5

E7E8E9

–

E10E11

–

E12

–

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

Commands

Table6 and Table 7 provide a quick reference of

available comm ands, foll owed by a descri ption of each

command. Two additional truth tables, Table9 on

page 42, an d Table 10 on page 44, appe ar f ollowing the

Operation section, provide current state/next state

information.

NOTE:

1. CKE is HIGH for all commands shown except SELF REFRESH.

2. BA0–BA1 select either the mode register or the extended mode register (BA0 = 0, BA1 = 0 select the mode register;

BA0 = 1, BA1 = 0 select extended mode register; other combinations of BA0–BA1 are reserved). A0-A12 provide the op-

code to be written to the selected mode register.

3. BA0–BA1 provide bank address and A0–A12 provide row address.

4. BA0–BA1 provide bank address; A0–Ai prov ide column add res s, (where i = 8 for x16, i = 9 for x8, and i = 9,11 for x4) A10

HIGH enables the auto precharge feature (nonpersistent); and A10 LO W disa bles the auto precharge feature.

5. A10 LOW: BA0–BA1 determine which bank is precharged.

A10 HIGH: all banks are precharged and BA0–BA1 are “Don’t Care.”

6. This command is AUTO REFRESH if CKE is HIGH, SELF REFRESH if CKE is LOW.

7. Internal refresh counter controls row addressing; within the self refresh mode, all inputs and I/Os are “Don’t Care”

except for CKE.

8. Applies only to READ bu rsts with auto precharge disa bled; this command is undefined (and should not be used) for READ

bursts with auto precharge enabled and for WRITE bursts.

9. DESELECT and NOP are functionally interchangeable .

NOTE:

1. Used to mask write data; provided coincident with the corresponding data.

Table 6: Trut h Table – Commands

Note 1 applies to all commands

NAME (FUNCTION) CS# RAS# CAS# WE# ADDR NOTES

DESELECT (NOP) HXXX X 9

NO OPERATION (NOP) LHHH X 9

ACTIVE (Select bank and act ivate row) L L H H Bank/Row 3

READ (Select bank and column, and start READ burst) L H L H Bank/Col 4

WRITE (Select bank and column, and start WRITE burst) L H L L Bank/Col 4

BURST TERMINATE LHHL X 8

PRECHARGE (Deactivate row in bank or banks) L L H L Code 5

AUTO REFRES H or SELF REFRESH

(Enter self refresh mode) LLLH X6, 7

LOAD MODE REGISTER LLLLOp-Code2

Ta ble 7: Truth Table – DM Operation

Note 1 applies to all commands

NAME (FUNCTION) DM DQ

Write Enable L Valid

Write Inhibit HX

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

DESELECT

The DESELECT function (CS# HIGH) prevents new

commands from being executed by the DDR SDRAM.

The DDR SDRAM is effectively deselected. Operations

already in progress are not affecte d.

NO OPERATION (NOP)

The NO OPERATION (NOP) command is used to

instruct the selected DDR SDRAM to perform a NOP

(CS# is LOW with RAS#, CAS#, and WE# are HIGH).

This prevents unwanted commands from being regis-

tered during idle or wait states. Operations already in

progress are not affec ted.

LOAD MODE REGISTER

The mode registers are loaded via inputs A0–A12.

See mode register descriptions in the Register Defini-

tion section on page 12. The LOAD MODE REGISTER

command can only be issued when all banks are idle,

and a subsequent executable command cannot be

issued until tMRD is met.

ACTIVE

The ACTIVE command is used to open (or activate)

a row in a part icular bank for a subsequent ac cess. The

value on the BA0, BA1 inputs selects the bank , and the

address provided on inputs A0–A12 selects the row.

This row remains active (or open) for accesses until a

PRECHARGE command is issued to that bank. A PRE-

CHARGE command must be issued before opening a

different row in the same bank.

READ

The R EAD com mand is used t o initiate a burs t read

access to an active row. The value on the BA0, BA1

inputs selects the bank, and the address provided on

inputs A0–Ai (where i = 8 for x16, 9 for x8, or 9, 11 for

x4) selects the starting column location. The value on

input A10 de termines whether or not a ut o precharge is

used. If auto precharge is selected, the row being

accessed will be precharged at the end of the READ

burst; if auto precharge is not selected, the row will

remain open for subsequent accesses.

WRITE

The WRITE command is used to initiate a burst

write access to an active row. The value on the BA0,

BA1 inputs selects the bank, and the address provided

on inputs A0–Ai (wher e i = 8 for x16, 9 for x8, or 9, 11 for

x4) selects the starting column location. The value on

input A10 de termines whether or not a ut o precharge is

used. If auto precharge is selected, the row being

accessed will be precharged at the end of the WRITE

burst; if auto precharge is not selected, the row will

remain open for subsequent accesses. Input data

appearing on the DQ is written to the memory array

subject to the DM input logic level appearing coinci-

dent with the data. If a given DM signal is registered

LOW, the corresponding data will be written to mem-

ory; if the DM signal is registered HIGH, the corre-

sponding data inputs will be ignored and a WRITE will

not be executed to that byte/col umn loca tion.

PRECHARGE

The PRECHARGE command is used to deactivate

the open r ow in a pa rtic ul ar ba nk or the open r ow in all

banks. The bank(s) will be available for a subsequent

row access a s pecifi ed t ime (tRP) af ter th e PRECHARGE

command is issued, except in the case of concurrent

auto precharge, where a READ or WRITE command to

a different bank is allowed as long as it does not inter-

rupt the data transfer in the current bank and does not

violate any other timing parameters. Input A10 deter-

mines whether one or all banks are to be precharged,

and in the case where only one bank is to be pre-

charged, inputs BA0, BA1 select the bank. Otherwise,

BA0, BA1 are treated as “Don’t Care.” Once a bank has

been precharged, it is in the idle state and must be

activated prior to any READ or WRITE commands

being issued to that bank. A PRECHARGE command

will be treated as a NOP if there is no open row in that

bank (idle state) or if the previously open row is

already in the process of precharging.

Auto Precharge

Auto precharge is a feature that performs the same

individual-bank precharge function described above,

but without requiring an explicit command. This is

accomplished by using A10 to enable auto precharge

in conjunction with a specific READ or WRITE com-

mand. A precharge of the bank/row that is addressed

with the READ or WRITE command is automatically

performed upon completion of the READ or WRITE

burst. Auto precharge is nonpersistent in that it is

either enabled or disabled for each individual READ or

WRITE command. This device supports concurrent

auto precharge if the command to the other bank does

not interrupt the data transfer to the current bank.

Auto precharge ensures that the precharge is initi-

ated at th e earl iest val id stag e with in a burs t. This ea rli -

est valid stage is determined as if an explicit

PRECHARGE com mand w as issue d at th e ear liest po s-

sible time, without violating tRAS (MIN), as described

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

for each burst type in the Operation section of this

data shee t. The us er mu st not issu e an othe r comm and

to the same bank until the precharge time (tRP) is

completed.

BURST TERMINATE

The BURST TERMINATE command is used to trun-

cate READ bursts (with auto precharge disabled). The

most recently registered READ command prior to the

BURST TERMINATE command will be truncated, as

shown in the Ope ration section of this data s heet. The

open page, which the READ burst was terminated

from, remains open.

AUTO REFRESH

AUTO REFRESH is used during normal operation of

the DDR SDRAM and is analogous to CAS#-BEFORE-

RAS# (CBR) refresh in FPM/EDO DRAMs. This com-

mand is nonpersistent, so it must be issued each time

a refresh is required. All banks must be idle before an

AUTO REFRESH command is issued.

The addressing is generated by the internal refresh

controller. This makes the address bits a “Don’t Care”

during an AUTO REFRESH command. The 256Mb

DDR SDRAM requires AUTO REFRESH cycles at an

average interval of 7.8125µ s (max imum).

To allow for improved efficiency in scheduling and

switching between tasks, some flexibility in the abso-

lute refresh interval is provided. A maximum of eight

AUTO REFRESH commands can be posted to any

given DDR SDRAM, meaning that the maximum abso-

lute interval between any AUTO REFRESH command

and the next AUTO REFRESH command is 9 x 7.8125µs

(70.3µs). Note, the JEDEC specification only allows 8 x

7.8125µs, thus the Micron specification exceeds the

JEDEC requirement by one clock. This maximum

absolute interval is to allow future support for DLL

updates internal to the DDR SDRAM to be restricted to

AUTO REFRESH cycles, without allowing excessive

drift in tAC between updates.

Although not a JEDEC requirement, to provide for

future functionalities, CKE must be active (HIGH) dur-

ing the auto refresh period. The auto refresh period

begins when the AUTO REFRESH command is regis-

tered and ends tRFC later.

SELF REFRESH

The SEL F REFRESH com mand can be used to retain

data in the DDR SDRAM, even if the rest of the system

is powered down. When in the self refresh mode, the

DDR SDRAM retains data without external clocking.

The SELF REFRESH command is initiated like an

AUTO REFRESH command except CKE is disabled

(LOW). The DLL is automatically disabled upon enter-

ing SELF REF RESH and is automa tically ena bled upon

exiting SELF REFRESH. (A DLL reset and 200 clock

cycles must then occur before a READ command can

be issued.) Input signals except CKE are “Don’t Care”

during SELF REFRESH. VREF voltage is also r equir ed f or

the full duration of the SELF REFRESH.

The procedure for exiting self refresh requires a

sequence of commands. First, CK and CK# must be

stable prior to CKE going back HIGH. Once CKE is

HIGH, the DDR SDRAM must have NOP commands

issued for tXSNR because time is required for the com-

pletion of any internal refresh in progress. A simple

algorithm for meeting both refresh and DLL require-

ments is to apply NOPs for tXSNR time, then a DLL

reset and NOPs for 200 additional clock cycles before

applying an y other command.

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

Operations

Bank/Row Activation

Before any READ or WRITE commands can be

issued to a bank within the DDR SDRAM, a row in that

bank must be “opened.” This is accomplished via the

ACTIVE command, which selects both the bank and

the row to be act i vated, as shown in Figure 10.

After a row is opened with an ACTIVE command, a

READ or WRITE command may be issued to that row,

subject to the tRCD specification. tRCD (MIN) should

be divided by the clock period and rounded up to the

next whole number to determine the earliest clock

edge after the ACTIVE command on which a READ or

WRITE command can be entered. For example, a tRCD

specification of 20ns with a 133 MHz clock (7.5ns

period) results in 2.7 clocks rounded to 3. This is

reflected in Figure11, wh ich c overs any case where 2 <

tRCD (MIN)/tCK £ 3. (Figure 11 also shows the same

case for tRRD; the same procedure is used to convert

other specification limits from time units to clock

cycles.)

A subsequent ACTIVE command to a different row

in the same bank can only be issued after the previous

active row has been “closed” (precharged). The mini-

mum time interval between successive ACTIVE com-

mands to the same bank is defined by tRC.

A subsequent ACTIVE command to another bank

can be issued while the first bank is being accessed,

which results in a reduction of total row-access over-

head. The minimum time interval between successive

ACTIVE commands to different banks is defined by

tRRD.

Figur e 10: Activating a Specific Row in

a Specific Bank

Figure 11: Example: Meeting tRCD (tRRD) MIN When 2 < tRCD ( tRRD) MIN/tCK £ 3

CS#

WE#

CAS#

RAS#

CKE

A0–A12 RA

RA = Row Address

BA = Bank Address

HIGH

BA0, BA1 BA

CK#

COMMAND

BA0, BA1

ACT ACT

NOP

RRD tRCD

CK#

Bank x Bank y

A0–A12

Row Row

NOP RD/WR

NOP

Bank y

Col

NOP

T0 T1 T2 T3 T4 T5 T6 T7

DON’T CARE

NOP

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

READs

READ bursts are initiated with a READ command, as

shown in Figure 12 on page 21.

The starting column and bank addresses are pro-

vided with the READ command and auto precharge is

either enabled or disabled for that burst access. If auto

precharge is enabled, the row being accessed is pre-

charged at the co mpletion of the burst.

NOTE: For the READ commands used in the follow-

ing illust rat i ons, auto precharge is disabled.

During READ bursts, the valid data-out element

from the sta rting column ad dress will be available fol-

lowing the CAS latency after the READ command.

Each subsequent data-out element will be valid nomi-

nally at th e nex t pos iti ve or nega ti ve c lock e dge (i.e., at

the next crossing of CK an d CK#). Figure 13 on page 22

shows general timing for each possible CAS latency

setting. DQS is driven by the DDR SDRAM along with

output d ata . Th e in itia l LOW state on DQ S is known a s

the read preamble; the LOW state coincident with the

last data -out element is known as the read postamble.

Upon completion of a burst, assuming no other

commands have been initiated, the DQs will go High-

Z. A detailed explanation of tDQSQ (valid data-out

skew), tQH (data-out window hold), and the valid data

window are depicted in Figure40 on page 65 and

Figure 41 on page 66. A detailed explanation of

tDQSCK (DQS transition skew to CK) and tA C (dat a-ou t

transition skew to CK) is depicted in Figure 42 on

page 67.

Data from any READ burst may be concatenated

with or truncated with data from a subsequent READ

command. In either case, a continuous flow of data

can be maintained. The first data element from the

new burst follows either the last element of a com-

pleted bur st or t he last d esir ed da ta e lement of a longe r

burst which is being truncated. The new READ com-

mand should be issued x cycles after the first READ

command, where x equals the number of desired data

element pairs (pairs are required by the 2n-prefetch

architecture). This is shown in Figure 14 on p age23. A

READ command can be initiated on any clock cycle

foll o w in g a pr ev iou s REA D com mand . N o nco nse cut iv e

read data is illustrated in Figure 15, Nonconsecutive

READ Bursts, on page 24. Full-speed random read

accesse s within a page (or pages) can be per formed a s

shown in Figure16, Random READ Accesses, on

page 25.

Data from any READ bu rst may be t run cate d wi th a

BURST TERMINATE command, as shown in Figure 17

on page 26. The BURST TERMINATE latency is equal

to the read (CAS) latency; i.e., the BURST TERMINATE

command should be issued x cycles after the READ

command, where x equals the number of desired data

element pairs (pairs are required by the 2n-prefetch

architecture).

Data from any READ burst must be completed or

truncated before a subsequent WRITE command can

be issued. If truncation is necessary, the BURST TER-

MINATE command must be used, as shown in

Figure 18 on page 27. The tDQSS (NOM) case is sho wn;

the tDQSS (MAX) case has a longer bus idle time.

(tDQSS [M IN ] and tDQSS [MAX] are defined in the sec-

tion on WRITEs.)

A READ burs t may be fol lowed b y, or truncated wit h,

a PRECHARGE command to the same bank provided

that auto precharge was not activated.

The PRECHARGE command should be issued x

cycles after the READ command, where x equals the

number of desired data element pairs (pairs are

required by the 2n-prefetch architecture). This is

shown in Figure 19 on page28. Following the PRE-

CHARGE command, a subsequent command to the

same bank cannot be issued until both tRAS and tRP

have been met. Note that part of the row precharge

time is hidden during the access of the last data ele-

ments.

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

Figure 12: READ Command

CS#

WE#

CAS#

RAS#

CKE

x4: A0–A9, A11

x8: A0–A9

x16: A0–A8

A10

BA0,1

HIGH

EN AP

DIS AP

x4: A12

x8: A11, A12

x16: A9, A11, A12

CK#

CA = Column Address

BA = Bank Address

EN AP = Enable Auto Precharge

DIS AP = Disable Auto Precharge

DON’T CARE

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

Figure 13: READ Burst

NOTE:

1. DO n = data-out from column n.

2. Burst length = 4.

3. Three subsequent elements of data-out appear in the programmed order following DO n.

4. Shown with nominal tAC, tDQSCK, and tDQSQ.

CK#

COMMAND READ NOP NOP NOP NOP NOP

ADDRESS Bank a,

Col n

READ NOP NOP NOP NOP NOP

Bank a,

Col n

CL = 2

CK#

COMMAND

ADDRESS

DQS

CL = 2.5

DQS

T0 T1 T2 T3T2n T3n T4 T5

DON’T CARE TRANSITIONING DATA

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

Figure 14: Consecutive READ Bur st s

NOTE:

1. DO n (or b) = data-out from column n (or column b).

2. Burst length = 4 or 8 (if 4, the bursts are concatenated; if 8, the second burst interrupts the first).

3. Three subsequent elements of data-out appear in the programmed order following DO n.

4. Three (or seven) subsequent elements of data-out appear in the programmed order following DO b.

5. Shown with nominal tAC, tDQSCK, and tDQSQ.

6. Example applies only when READ commands are issued to the same device.

CK#

COMMAND READ NOP READ NOP NOP NOP

ADDRESS Bank,

Col nBank,

Col b

COMMAND READ NOP READ NOP NOP NOP

ADDRESS Bank,

Col nBank,

Col b

CL = 2

CK#

COMMAND

ADDRESS

DQS

CL = 2.5

DQS

nDO

T0 T1 T2 T3T2n T3n T4 T5T4n T5n

DON’T CARE TRANSITIONING DATA

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

Figure 15: Nonconsecutive READ Bursts

NOTE:

1. DO n (or b) = data-out from column n (or column b).

2. Burst length = 4 or 8 (if 4, the bursts are concatenated; if 8, the second burst interrupts the first).

3. Three subsequent elements of data-out appear in the programmed order following DO n.

4. Three (or seven) subsequent elements of data-out appear in the programmed order following DO b.

5. Shown with nominal tAC, tDQSCK, and tDQSQ.

CK#

COMMAND READ NOP NOP NOP NOP NOP

ADDRESS Bank,

Col n

READ

Bank,

Col b

COMMAND

ADDRESS

CL = 2

CK#

COMMAND

ADDRESS

DQS

CL = 2.5

DQS

T0 T1 T2 T3T2n T3n T4 T5 T5n T6

READ NOP NOP NOP NOP NOP

Bank,

Col n

READ

Bank,

Col b

T0 T1 T2 T3T2n T3n T4 T5 T5n T6

nDO

DON’T CARE TRANSITIONING DATA

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

Figure 16: Random READ Accesses

NOTE:

1. DO n (or x or b or g) = data-out from column n (or column x or column b or column g).

2. Burst length = 2, 4 or 8 (if 4 or 8, the following burst interrupts the previous).

3. n' or x' or b' or g' indicates the next data-out following DO n or DO x or DO b or DO g, respectively.

4. READs are to an active row in any bank.

5. Shown with nominal tAC, tDQSCK, and tDQSQ.

CK#

COMMAND READ READ READ NOP NOP

ADDRESS Bank,

Col nBank,

Col xBank,

Col b

Bank,

Col xBank,

Col b

READ

Bank,

Col g

COMMAND

ADDRESS

CL = 2

CK#

COMMAND

ADDRESS

DQS

CL = 2.5

DQS

nDO

x' DO

n' DO

xDO

nDO

n' DO

xDO

T0 T1 T2 T3T2n T3n T4 T5T4n T5n

READ READ READ NOP NOP

Bank,

Col n

READ

Bank,

Col g

T0 T1 T2 T3T2n T3n T4 T5T4n T5n

DON’T CARE TRANSITIONING DATA

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

Figure 17: Terminating a READ Burst

NOTE:

1. DO n = data-out from column n.

2. Burst length = 4 or 8.

3. Subsequent element of data-out appears in the programmed order following DO n.

4. Shown with nominal tAC, tDQSCK, and tDQSQ.

5. BST = BURST TERMINAT E command; page remains open.

CK#

COMMAND READ BST5NOP NOP NOP NOP

ADDRESS Bank a,

Col n

READ BST5NOP NOP NOP NOP

Bank a,

Col n

CL = 2

CK#

COMMAND

ADDRESS

DQS

CL = 2.5

DQS

T0 T1 T2 T3T2n T4 T5

DON’T CARE TRANSITIONING DATA

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

Figure 18: READ to WRITE

NOTE:

1. DO n = data-out from column n.

2. DI b = data-in from column b.

3. Burst length = 4 in the cases shown (applies for bursts of 8 as well; if the burst length is 2, the BST command shown can

be NOP).

4. One subsequent element of data-out appears in the programmed order following DO n.

5. Data-in elements are applied following DI b in the programmed order.

6. Shown with nominal tAC, tDQSCK, and tDQSQ.

7. BST = BURST TERMINATE command;

8. page remains open.

CK#

COMMAND

READ BST

NOP NOP NOP

ADDRESS

Bank,

Col n

WRITE

Bank,

Col b

T0 T1 T2 T3T2n T4 T5T4n T5n

CL = 2

DQS

(NOM)

DQSS

CK#

COMMAND

READ BST

NOP WRITE NOP

ADDRESS

Bank a,

Col n

NOP

T0 T1 T2 T3T2n T4 T5 T5n

CL = 2.5

DQS

DON’T CARE TRANSITIONING DATA

(NOM)

DQSS

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

Figure 19: READ to PRECHARGE

NOTE:

1. DO n = data-out from column n.

2. Burst length = 4, or an interrupted burst of 8.

3. Three subsequent elements of data-out appear in the programmed order following DO n.

4. Shown with nominal tAC, tDQSCK, and tDQSQ.

5. READ to PRECHARGE equals two clocks, which allows two data pairs of data-out.

6. A READ command with AUTO-PRECHARGE enabled, provided tRAS (MIN) is met, would cause a precharge to be per-

formed at x number of clock cycles after the READ command, where x = BL / 2.

7. An active command to the same bank is only allowed if tRC (MIN) has been satisfied.

8. PRE = PRECHARGE co mmand; ACT = ACTIVE command.

CK#

COMMAND

READ NOP PRE NOP NOP ACT

ADDRESS Bank a,

Col nBank a,

(a or all)Bank a,

Row

READ NOP PRE NOP NOP ACT

Bank a,

Col n

CL = 2 tRP

tRP

CK#

COMMAND

ADDRESS

DQS

CL = 2.5

DQS

T0 T1 T2 T3T2n T3n T4 T5

Bank a,

(a or all)Bank a,

Row

DON’T CARE TRANSITIONING DATA

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

WRITEs

WRITE b ursts are initiated with a W RIT E command,

as shown in Figu re 20.

The starting column and bank addresses are pro-

vided with the WRITE command, and auto precharge

is either enabled or disabled for that access. If auto

precharge is enabled, the row being accessed is pre-

charged at the completion of the burst and after the

tWR time.

NOTE: For the WRITE commands used in the follo w-

ing illust rat i ons, auto precharge is disabled.

During WRITE bu rsts, the first valid data-in element

will be register ed on th e f irs t ri s ing edg e of DQS f o llow-

ing the WRITE command, and subsequent data ele-

ments will be registered on successive edges of DQS.

The LOW state on DQS between the WRITE command

and the first rising edge is known as the write pream-

ble; the LOW state on DQS following the last data-in

element is known as the write postamble.

The time between the WRITE command and the

first corresponding rising edge of DQS (tDQSS) is

specified with a relatively wide range (from 75 per-

cent to 125 percent of one clock cycle). All of the

WRITE diagrams show the nominal case, and where

the two extreme cases (i.e., tDQSS [MIN] and tDQSS

[MAX]) might not be intuitive, they have also been

included. Figure 21 on page 30 shows the nominal

case and the extremes of tDQSS for a burst of 4.

Upon completion of a burst, assuming no other

commands have been initiated, the DQ will remain

High-Z and any additional input data will be

ignored.

Data for any WRITE burst may be concatenated

with or truncated with a subsequent WRITE com-

mand. In either case, a continuous flow of input data

can be m aintain ed. The n ew WRITE command can be

issued on any positive edge of clock following the pre-

vious WRITE command. The first data element from

the new burst is applied after either the last element of

a completed burst or the last desired data element of a

longer burst which is being truncated. The new WRITE

command should be issued x cycles after the first

WRITE command, where x equals the number of

desired data element pairs (pairs are required by the

2n-prefetch architecture).

Figure 22 on page 31 shows concatenated bursts of

4. An example of nonconsecutive WRITEs is shown in

Figure23 on page 32. Full-speed random write

accesses within a page or pages can be performed as

shown in Figure 24 on page 33.

Figure 20: WRITE Command

Data for any WRITE bu rst may be fol l owed by a sub-

sequent READ command. To follow a WRITE without

truncating the WRITE burst, tWTR should be met as

shown in Figure 25 on page 34.

Data for any WRITE burst may be truncated by a

subseq u e nt READ co mma nd, as sho wn i n Figu re 26 on

page 35.

Note that only the data-in pairs that are registered

prior to the tWTR period are written to the internal

array, and any subsequent data-in should be masked

with DM, as shown in Figure 27 on page 36.

Data for any WRITE bu rst may be fol l owed by a sub-

sequent PRECHARGE command. To follow a WRITE

without truncating the WRITE burst, tWR should be

met as shown in Figure 28 on page 37.

Data for any WRITE burst may be truncated by a

subsequent PRECHARGE command, as shown in

Figure 29 on page 38 and Figure 30 on page 39. Note

that only the data-in pairs that are registered prior to

the tWR period are written to the internal array, and

any subs equen t data-in should be m asked w ith DM as

shown in Figures 29 and 30. After the PRECHARGE

command, a subsequent command to the same bank

cannot be issued until tRP is met.

CS#

WE#

CAS#

RAS#

CKE

A10

BA0, 1

HIGH

EN AP

DIS AP

CK#

CA = Column Address

BA = Bank Address

EN AP = Enable Auto Precharge

DIS AP = Disable Auto Precharge

DON’T CARE

x4: A0–A9, A11

x8: A0–A9

x16: A0–A8

x4: A12

x8: A11, A12

x16: A9, A11, A12

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

Figure 21: W RITE Burst

NOTE:

1. DI b = data-in for column b.

2. Three subsequent elements of data-in are applied in the programmed order following DI b.

3. An uninterrupted burst of 4 is shown.

4. A10 is LOW with the WRITE command (auto precharge is disabled).

DQS

tDQSS (MAX)

tDQSS (NOM)

tDQSS (MIN)

tDQSS

CK#

COMMAND

WRITE NOP NOP

ADDRESS

Bank a,

Col b

NOP

T0 T1 T2 T3T2n

DQS

tDQSS

DQS

tDQSS

DON’T CARE TRANSITIONING DATA

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

Figure 22: Consecutive WRITE to WRITE

NOTE:

1. DI b, etc., = data-in for column b, etc.

2. Three subsequent elements of data-in are applied in the programmed order following DI b.

3. Three subsequent elements of data-in are applied in the programmed order following DI n.

4. An uninterrupted burst of 4 is shown.

5. Each WRITE command may be to any bank.

CK#

COMMAND WRITE NOP WRITE NOP NOP

ADDRESS Bank,

Col b

NOP

Bank,

Col n

T0 T1 T2 T3T2n T4 T5T4nT3nT1n

DQS

DON’T CARE TRANSITIONING DATA

DQSS

DQSS (NOM)

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

Figure 23: Nonconsecutive WRITE to WRITE

NOTE:

1. DI b, etc., = data-in for column b, etc.

2. Three subsequent elements of data-in are applied in the programmed order following DI b.

3. Three subsequent elements of data-in are applied in the programmed order following DI n.

4. An uninterrupted burst of 4 is shown.

5. Each WRITE command may be to any bank.

CK#

COMMAND WRITE NOP NOP NOP NOP

ADDRESS Bank,

Col b

WRITE

Bank,

Col n

T0 T1 T2 T3T2n T4 T5T4nT1n T5n

DQS

tDQSS (NOM) tDQSS

DON’T CARE TRANSITIONING DATA

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

Figure 24: Ran dom W RITE Cycles

NOTE:

1. DI b, etc., = data-in for column b, etc.

2. b', etc., = the next data-in following DI b, etc., according to the programmed burst order.

3. Programmed burst length = 2, 4, or 8 in cases shown.

4. Each WRITE command may be to any bank.

tDQSS (NOM)

CK#

COMMAND WRITE WRITE WRITE WRITE NOP

ADDRESS Bank,

Col bBank,

Col xBank,

Col nBank,

Col g

WRITE

Bank,

Col a

T0 T1 T2 T3T2n T4 T5T4nT1n T3n T5n

DQS

bDI

b' DI

xDI

x' DI

nDI

n' DI

aDI

a' DI

gDI

DON’T CARE TRANSITIONING DATA

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

Figure 25: WRITE to R EAD - Uninterrup ting

NOTE:

1. DI b = data-in for column b; DO n = data-out for column n.

2. Three subsequent elements of data-in are applied in the programmed order following DI b.

3. An uninterrupted burst of 4 is shown.

4. tWTR is referenced from the first positive CK edge after the last data-in pair.

5. The READ and WRITE commands are to the same device. However, the READ and WRITE commands may be directed to

different devices, in which case, tWTR is not required and the READ command could be applied earlier.

6. A10 is LOW with the WRITE command (auto precharge is disabled).

tDQSS (NOM)

CK#

COMMAND

WRITE NOP NOP READ NOP NOP

ADDRESS

Bank a,

Col bBank a,

Col n

NOP

T0 T1 T2 T3T2n T4 T5T1n T6 T6n

tWTR

CL = 2

DQS

bDO

tDQSS

tDQSS (MIN) CL = 2

DQS

bDO

tDQSS

tDQSS (MAX) CL = 2

DQS

bDO

tDQSS

DON’T CARE TRANSITIONING DATA

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

Figure 26: WRITE to READ – In te r rupting

NOTE:

1. DI b = data-in for column ;, DO n = data-out for column n.

2. An interrupted burst of 4 is shown; two data elements are written.

3. One subsequent element of data-in is applied in the programmed order following DI b.

4. tWTR is referenced from the first positive CK edge after the last data-in pair.

5. A10 is LOW with the WRITE command (auto precharge is disabled).

6. DQS is required at T2 and T2n (nominal case) to register DM.

7. If the burst of 8 was used, DM and DQS would be required at T3 and T3n because the READ command would not mask

these two data elements.

tDQSS (NOM)

CK#

COMMAND WRITE NOP NOP NOP NOP NOP

ADDRESS Bank a,

Col bBank a,

Col n

READ

T0 T1 T2 T3T2n T4 T5 T5nT1n T6 T6n

tWTR

CL = 2

DQS

bDO

tDQSS (MIN) CL = 2

DQS

tDQSS (MAX) CL = 2

DQS

bDO

DON’T CARE TRANSITIONING DATA

tDQSS

T3n

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

Figure 27: WRITE to READ – Odd Number of Data, Interrupting

NOTE:

1. DI b = data-in for column b; DO n = data-out for column n.

2. An interrupted burst of 4 is shown; one data element is written.

3. tWTR is referenced from the first positive CK edge after the last desired data-in pair (not the last two data elements).

4. A10 is LOW with the WRITE command (auto precharge is disabled).

5. DQS is required at T1n, T2, and T2n (nominal case) to register DM.

6. If the burst of 8 was used, DM and DQS would be require d at T3–T3 n becau se the READ command wou ld not mask these

data elements.

tDQSS (NOM)

CK#

COMMAND

WRITE NOP NOP NOP NOP NOP

ADDRESS

Bank a,

Col bBank a,

Col n

READ

T0 T1 T2 T3T2n T4 T5T1n T6 T6nT5n

tWTR

CL = 2

DQS

bDO

tDQSS (MIN) CL = 2

DQS

bDO

tDQSS (MAX) CL = 2

DQS

bDO

DON’T CARE TRANSITIONING DATA

tDQSS

T3n

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

Figure 28: WRITE to PRECHA RG E - Uninterr upting

NOTE:

1. DI b = data-in for column b.

2. Three subsequent elements of data-in are applied in the programmed order following DI b.

3. An uninterrupted burst of 4 is shown.

4. tWR is referenced from the first positive CK edge after the last data-in pair.

5. The P REC HAR G E an d WRI TE c om ma nds are t o th e same dev ic e. H o we ver, the PRECHARGE and WRIT E c om man ds ma y b e

to different devices, in which case, tWR is not required and the PRECHARGE command could be applied earlier.

6. A10 is LOW with the WRITE command (auto precharge is disabled).

7. PRE = PRECHAR GE command.

tDQSS (NOM)

CK#

COMMAND WRITE NOP NOP NOP PRE7NOP

ADDRESS Bank a,

Col bBank,

(a or all)

NOP

T0 T1 T2 T3T2n T4 T5T1n T6

tWR tRP

DQS

tDQSS (MIN)

DQS

tDQSS (MAX)

DQS

DON’T CARE TRANSITIONING DATA

tDQSS

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

Figure 29: WRITE to PRECHARGE – Interrupti ng

NOTE:

1. DI b = data-in for column b.

2. Subsequent element of data-in is applied in the programmed order following DI b.

3. An interrupted burst of 8 is shown; two data elements are written.

4. tWR is referenced from the first positive CK edge after the last data-in pair.

5. A10 is LOW with the WRITE command (auto precharge is disabled).

6. DQS is required at T4 and T4n (nominal case) to register DM.

7. If the burst of 4 was used, DQS and DM would not be required at T3, T3n, T4, and T4n.

8. PRE = PRECHARGE command.

tDQSS

tDQSS (NOM)

CK#

COMMAND WRITE NOP NOP PRE8NOP NOP

ADDRESS Bank a,

Col bBank,

(a or all)

NOP

T0 T1 T2 T3T2n T4 T5T1n T6

tWR tRP

DQS

tDQSS

tDQSS (MIN)

DQS

tDQSS

tDQSS (MAX)

DQS

DON’T CARE TRANSITIONING DATA

T3n T4n

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

Figure 30: WRITE to PRECHARGE – Odd Number of Data – Inter rupt in g

NOTE:

1. DI b = data-in for column b.

2. An interrupted burst of 8 is shown; one data element is written.

3. tWR is referenced from the first positive CK edge after the last data-in pair.

4. A10 is LOW with the WRITE command (auto precharge is disabled).

5. DQS is required at T4 and T4n (nominal case) to register DM.

6. If the burst of 4 was used, DQS and DM would not be required at T3, T3n, T4, and T4n.

7. PRE = PRECHARGE command.

tDQSS

tDQSS (NOM)

CK#

COMMAND WRITE NOP NOP PRE7NOP NOP

ADDRESS Bank a,

Col bBank,

(a or all)

NOP

T0 T1 T2 T3T2n T4 T5T1n T6

tWR tRP

DQS

tDQSS

tDQSS (MIN)

DQS

tDQSS

tDQSS (MAX)

DQS

DON’T CARE TRANSITIONING DATA

T3n T4n

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

PRECHARGE

The PRECHARGE command, as shown in Figure 31,

is used to deactivate the open row in a particular bank

or the open row in all banks. The bank(s) will be avail-

able for a subsequent row access some specified time

(tRP) after the PRECHARGE command is issued. Input

A10 determines whether one or all banks are to be pre-

charged, and in the case where only one bank is to be

precharged, inputs BA0, BA1 select the bank. When all

banks are to be precharged, inputs BA0, BA1 are

treated as “Don’t Care.” Once a bank has been pre-

charged, it is in the idle state and must be activated

prior to any READ or WRITE commands being issued

to that bank.

Figure 31: PRECHARGE Command

Power-Down (CKE Not A c tive)

Unlike SDR SDRAM s, DDR SDRAMs require CKE to

be active at all times that an access is in progress, from

the issuing of a READ or WRITE command until com-

pletion of the access. Thus, a clock susp en d is not sup-

ported. For READs, an access completion is defined

when the read postamble is satisfied; for WRITEs, an

access completion is defined when the write recovery

time (tWR) is satisfied.

Power-down, shown in Figure 32, Power-Down, on

page 41, is entered when CKE is registered LOW and all

of the criteria listed in Table 8, on page 41, are met. If

power- down occurs when all banks are idle, this mode

is referred to as prec harge power-down; if power-down

occurs when there is a row active in any bank, this

mode is referred to as active power-down. Entering

power-down deactivates the input and output buffers,

excluding CK, CK#, and CKE. F or maximum power sav-

ings, the DLL is frozen during precharge power-down

mode. Exiting power-down requires the device to be at

the same voltage and frequency as when it entered

power-down. However, power-down duration is lim-

ited by the refresh requirements of the device (tREFC).

While in power-down, CKE LOW and a stable clock

signal must be maintained at the inputs of the DDR

SDRAM, while all other input signals are “Don’t Care.”

The power-down state is synchronously exited when

CKE is registered HIGH (in conjun ction with a N OP or

DESELECT command). A valid executable command

may be applied one clock cycle later.

CS#

WE#

CAS#

RAS#

CKE

A10

BA0,1

HIGH

ALL BANKS

ONE BANK

A0–A9, A11, A12

CK#

BA = Bank Address (if A10 is LOW;

otherwise “Don’t Care”)

DON’T CARE

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

Figure 32: Power-Down

NOTE:

1. CKEn is the logic state of CKE at clock edge n; CKEn-1 was the state of CKE at the previous clock edge.

2. Current state is the state of the DDR SDRAM immediately prior to clock edge n.

3. COMMANDn is the command registered at clock edge n, and ACTIONn is a result of COMMANDn.

4. All states and sequences not shown are illegal or reserved.

5. CKE must not d rop L OW durin g a c olumn a ccess. For a RE AD, this m ea ns CKE mu st stay HI GH until after the read po sta m-

ble time; for a WRITE, CKE must stay HIGH until the WRITE recovery time (tWR) has been met.

6. Once initialized, including during self refresh mode, VREF must be powered within the specified range.

7. Upon exit of the self refresh mode, the DLL is automatically enabled, but a DLL reset must still occur. A minimum of 200

clock cycles is needed before applying a READ command for the DLL to lock. DESELECT or NOP commands should be

issued on any clock edges occurring during the tXSNR period.

tIS tIS

No READ/WRITE

access in progress Exit power-down mode

Enter power-down mode

CKE

CK#

COMMAND NOP

()()

NOP VALID

T0 T1 T2 Ta0 Ta1 Ta2

VALID

DON’T CARE

VALID

Table 8: Truth Table – CKE

Notes: 1–6

CKEn-1 CKEnCURRENT STATE COMMANDnACTIONnNOTES

LLPower-Down X Maintain Power-Down

Self Refresh X Maintain Self Refresh

L H Power-Down DESELECT or NOP Exit Power-Down

Self Refresh DESELECT or NOP Exit Self Refresh 7

H L All Banks Idle DESELECT or NOP Precharg e Power-Down Entry

Bank(s) Active DESELECT or NOP Active Power-Down Entry

All Banks Idle AUTO REFRESH Self Refresh Entry

H H See Table 9 on page 42

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

NOTE:

1. This table applies when CKEn-1 was HIGH and CKEn is HIGH (see Table 8 on page 41) and after tXSNR has been met (if the

previous state was self refresh).

2. This table is bank-specific, except where noted (i.e., the current state is for a specific bank and the commands shown are

those allowed to be issued to that bank when in that state). Exceptions are covered in the notes below.

3. Current state definitions:

Idle: The bank has been precharged, and tRP has been met.

Row Active: A row in the bank has been activated, and tRCD has been met. No data bursts/accesses and no register

accesses are in progress.

Read: A READ burst has been initiated, with auto precharge disabled, and has not yet terminated or been termi-

nated.

Write: A WRITE burst has been initiated, with auto precharge disabled, and has not yet terminated or been ter-

minated.

4. The following states must not be interrupted by a command issued to the same bank. COMMAND INHIBIT or NOP com-

mands, or allowable commands to the other bank should be issued on any clock edge occurring during these states.

Allowable comm ands to the other bank are determined by its c urrent state an d Table 9, Truth Ta ble – C urrent State Bank

n – Command to Bank n, on page 42 and according to Table 10, Truth Table – Current State Bank n– Command to Bank

m, on page 44.

Precharging: Starts with registration of a PRECHARGE command and ends when tRP is met. Once tRP is met, the bank

will be in the idle state.

Row

Activating: Starts with registration of an ACTIVE command and ends when tRCD is met. Once tRCD is met, the bank

will be in the “row active” state.

Read w/Auto-Prec ha rge

Enabled: Starts with registration of a READ command with auto precharge enabled and ends when tRP has been-

met. On ce tRP is met, the bank will be in the idle state.

Write w/A u to - Prech arge

Enabled: Starts with registration of a WRITE command with auto precharge enabled and ends when tRP has been

met. On ce tRP is met, the bank will be in the idle state.

Table 9: Truth Table – Current State Bank n – Command to Bank n

Notes: 1–6; notes appear below and on next page

CURRENT STATE CS# RAS# CAS# WE# COMMAND/ACTION NOTES

Any H X X X DESELECT (NOP/continue previous operation)

LHH H

NO OPERATION (NOP/continue previous operation)

Idle L L H H ACTIVE (select and activate row)

LLL H

AUTO REFRESH 7

LLL L

LOAD MODE REGISTER 7

Row Active L H L H READ (select column and start READ burst) 10

LHL L

WRITE (select column and start WRITE burst) 10

LLH L

PRECHARGE (deactivate row in bank or banks) 8

Read

(Auto-

Precharge

Disabled)

LHL H

READ (select column and start new READ burst) 10

LHL L

WRITE (select column and start WRITE burst) 10, 12

LLH L

PRECHARGE (truncate READ burst, start PRECHARGE) 8

LHH L

BURST TERMINATE 9

Write

(Auto-

Precharge

Disabled)

LHL H

READ (select column and start READ burst) 10, 11

LHL L

WRITE (select column and start new WRITE burst) 10

LLH L

PRECHARGE (truncate WRITE burst, start PRECHARGE) 8, 11

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

5. The following states must not be interrupted by any executable command; COMMAND INHIBIT or NOP commands must

be applied on each positive clock edge during these states.

Refreshing: Starts with registration of an AUTO REFRESH command and ends when tRFC is met. Once tRFC is met, the

DDR SDRAM will be in the all banks idle state.

Accessing Mode

tMRD is met, the DDR SDRAM will be in the all banks idle state.

Precharging

All: Starts with registration of a PRECHARGE ALL command and ends when tRP is met. Once tRP is met, all

banks will be in the idle state.

6. All states and sequences not shown are illegal or reserved.

7. Not bank-specific; requires that all banks are idle and bursts are not in progress.

8. May or may not be bank-specific; if multiple banks are to be precharged, each must be in a valid state for precharging.

9. Not bank-specific; BURST TERMINATE affects the most recent READ burst, regardless of bank.

10.READs or WRITEs listed in the Command/Action column include READs or WRITEs with auto precharge enabled and

READs or WRITEs with auto precharge disabled.

11.Require s appropriate DM masking .

12.A WRITE command may be applied after the completion of the READ burst; otherwise, a BURST TERMINATE must be

used to end the READ burst prior to asserting a WRITE command.

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

NOTE:

1. This table applies when CKEn-1 was HIGH and CKEn is HIGH (see Truth Table 2) an d after tXSNR has been met (if the previ-

ous state was self refresh).

2. This tabl e descr ibes alt ernate ba nk o peratio n except w here noted (i.e., the c urrent st ate is f or ban k n and the commands

shown are those allowed to be issued to bank m, assuming that bank m is in such a state that the given command is

allowable). Exceptions are covered in the notes below.

3. Current state definitions:

Idle: The bank has been precharged, and tRP has been met.

Row Active: A row in the bank has been activated, and tRCD has been met. No data bursts/accesses and no register

accesses are in progress.

Read: A READ burst has been initiated, with auto precharge disabled, and has not yet terminated or been termi-

nated.

Write: A WRITE burst has been initiated, with auto precharge disabled, and has not yet terminated or been ter-

minated

Read with Auto Precharge Enabled: See following text – 3a

Write with Auto Precharge Enabled: See following text – 3a

a. The r ead with auto precharge enabled or write with au to precharge enabled state s can each be broken into two

parts: the access period and the precharge p eriod. For rea d with auto precha rge, the precharge period is defined as if

the same burst was executed with auto precharge disabled and then followed with the earliest possible PRECHARGE

command that still accesses all of the data in the burst. For write with auto precharge, the precharge period begins

when tWR ends, with tWR measured as if auto precharge was disabled. The access period starts with registration of

the command and ends where the precharge period (or tRP) begins.

Table 10: Truth Table – Current State Bank n– Command to Bank m

Notes: 1–6; notes appear below and on next page

CURRENT STATE CS# RAS# CAS# WE# COMMAND/ACTION NOTES

Any HX X X

DESELECT (NOP/continue previous operation)

LHHH

NO OPERATION (NOP/continue previous operation)

Idle XXX X

Any Command Otherwise Al lowed to Bank m

Row

Activating,

Act ive, or

Precharging

LLHH

ACTIVE (select and activate row)

LHL H

READ (select column and start READ burst) 7

LHL L

WRITE (select column and start WRITE burst) 7

LLHL

PRECHARGE

Read

(Auto-Precharge

Disabled)

LLHH

ACTIVE (select and activate row)

LHL H

READ (select column and start new READ burst) 7

LHL L

WRITE (select column and start WRITE burst) 7, 9

LLHL

PRECHARGE

Write

(Auto- Precharge

Disabled)

LLHH

ACTIVE (select and activate row)

LHL H

READ (select column and start READ burst) 7, 8

LHL L

WRITE (select column and start new WRITE burst) 7

LLHL

PRECHARGE

Read

(With Auto-

Precharge)

LLHH

ACTIVE (select and activate row)

LHL H

READ (select column and start new READ burst) 7, 3a

LHL L

WRITE (select column and start WRITE burst) 7, 9, 3a

LLHL

PRECHARGE

Write

(With Auto-

Precharge)

LLHH

ACTIVE (select and activate row)

LHL H

READ (select column and start READ burst) 7, 3a

LHL L

WRITE (select column and start new WRITE burst) 7, 3a

LLHL

PRECHARGE

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

This device supports concurrent auto precharge such that when a READ with auto precharge is enabled or a WRITE

with auto precharge is enabled any com mand to other banks is allowed, as long as that command does not interrupt

the read or write data transfer already in process. In either case, all other related limitations apply (e.g., contention

between read data and write data must be avoided).

b. The minimum delay from a READ or WRITE command with auto precharge enabled, to a command to a different

bank, is summarized below.

NOTE:

CLRU = CAS Latency (CL) rounded up to the next integer

BL = Bust length

4. AUTO REFRESH and LOAD MODE REGISTER commands may only be issued when all banks are idle.

5. A BURST T ERMINATE comm and cann ot be issue d to anoth er bank; it a pplies to the bank represented by the current state

only.

6. All states and sequences not shown are illegal or reserved.

7. READs or WRITEs listed in the Command/Action column include READs or WRITEs with auto precharge enabled and

READs or WRITEs with auto precharge disabled.

8. Requires appropriate DM masking.

9. A WRITE command may be applied after the completion of the READ burst; otherwise, a BURST TERMINATE must be

used to end the READ burst prior to asserting a WRITE command.

FROM COMMAND TO COMMAND MINIMUM DELAY

(WITH CONCURRENT AUTO PRECHARGE)

WRITE w/AP READ or READ w/AP [1 + (BL/2)] * tCK + tWTR

WRITE or WRITE w/AP (BL/2) * tCK

PRECHARGE 1 tCK

ACTIVE 1 tCK

READ w/AP READ or READ w/AP (BL/2) * tCK

WRITE or WRITE w/AP [CLRU + (BL/2)] *tCK

PRECHARGE 1 tCK

ACTIVE 1 tCK

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

Absolute Maximum Ratings

Stresses greater than those listed may cause perma-

nent damage to the device. This is a stress rating only,

and functional operation of the device at these or any

other conditions above those indicated in the opera-

tional sections of this specification is not implied.

Exposure to absolute maximum rating conditions for

extended peri ods may affec t reliability.

VDD Supply Voltage

Relative to Vss......................................-1V to +3.6V

VDDQ Supply Voltage

Rel a ti ve to VSS .....................................-1V to +3.6V

VREF and Inputs Voltage

Rel a ti ve to VSS .....................................-1V to +3.6V

I/O Pins Voltage

Rel a ti ve to VSS ....................... -0.5V to VDDQ +0.5V

Operatin g Temperature, TA

(ambient, Commercial) ..................... 0°C to +70°C

Operatin g Temperature, TA

(ambient, Industrial).......................-40°C to +85°C

Storage Temperature (plastic)...............-55 °C to +1 50°C

Po w er Dissipation........................................................1W

Short Circuit Output Current .................................50mA

Table 11: DC Electrical Characterist ics and Operating Conditions

0°C £ TA £ +70°C; VDDQ = +2.5V ±0.2V, VDD = +2.5V ±0.2V

Notes: 1–5, 16; notes appear on pages 59–62

PARAMETER/CONDITION SYMBOL MIN MAX UNITS NOTES

Supply Voltage VDD 2.3 2.7 V 36, 41,

I/O Supply Voltage VDDQ2.3 2.7 V 36, 41,

44,46

I/O Reference Voltage VREF 0.49 x VDDQ0.51 x VDDQV 6, 44

I/O Termination Voltage (system) VTT VREF - 0.04 VREF + 0.04 V7, 44

Input High (Logic 1) Voltage VIH(DC)VREF + 0.15 VDD + 0.3 V28

Input Low (Logic 0) Voltage VIL(DC)-0.3 VREF - 0.15 V28

INPUT LEAKAGE CURRENT

Any input 0V £ VIN £ VDD, VREF PIN 0V £ VIN £ 1.35V

(All other pins not under test = 0V)

II-2 2 µA

OUTPUT LEAKAGE CURRENT

(DQs are disabled; 0V £ VOUT £ VDDQ)IOZ -5 5 µA

OUTPUT LEVELS: Full drive option - x4, x8, x16

High Current (VOUT = VDDQ - 0.373V, minimum VREF,

minimum VTT)

IOH -16.8 - mA 37, 39

Low Current (VOUT = 0.373V, maximum VREF, maximum VTT)IOL 16.8 - mA

OUTPUT LEVELS: Reduced drive option - x16 only

High Current (VOUT = VDDQ - 0.763V, minimum VREF,

minimum VTT)

IOHR -9 - mA 38, 39

Low Current (VOUT = 0.763V, maximum VREF, maximum VTT)IOLR 9-mA

Table 12: AC Input Operating Conditions

0°C £ TA £ +70°C; VDDQ = +2.5V ±0.2V, VDD = +2.5V ±0.2V

Notes: 1–5, 14, 16; notes appear on pages 59–62

PARAMETER/CONDITION SYMBOL MIN MAX UNITS NOTES

Input High (Logic 1) Voltage VIH(AC)VREF + 0.310 - V 14, 28, 40

Input Low (Logic 0) Voltage VIL(AC)-VREF - 0.310 V 14, 28, 40

I/O Reference Voltage VREF(AC) 0.49 x VDDQ 0.51 x VDDQV6

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

Figur e 33: Input Voltage W aveform

0.940V

1.100V

1.200V

1.225V

1.250V

1.275V

1.300V

1.400V

1.560V

VILAC

VILDC

VREF -AC Noise

VREF -DC Error

VREF +DC Error

VREF +AC Noise

Receiver

Transmitter

VIHDC

VIHAC

VOH (MIN) (1.670V1 for SSTL_2 termination)

VINAC - Provides margin

between VOL (MAX) and VILAC

VSSQ

VDDQ (2.3V minimum)

VOL (MAX) (0.83V2 for

SSTL_2 termination)

System Noise Margin (Power/Ground,

Crosstalk, Signal Integrity Attenuation)

NOTE:

1. VOH (MIN) with test load is 1.927V

2. VOL (MAX) with test load is 0.373V

3. Numbers in diagram reflect nomimal

values utilizing circuit below.

Reference

Point

25Ω

VTT

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

Figure 34: SSTL _ 2 Clock Input

NOTE:

1. This provid es a m inim um of 1. 15V to a maximu m of 1.35V and is always hal f of V DDQ.

2. CK and CK# must cross in this region.

3. CK and CK# must meet at least VID(DC) MIN when static and is centered around VMP(DC)

4. CK and CK# must have a minimum 700mv peak-to-peak swing.

5. CK or CK# may not be more pos itive than VDDQ + 0.3V or mo re n egative tha n Vss - 0.3V.

6. For AC operation, all DC clock requirements must also be satisfied.

7. Numbers in diagram reflect nominal values.

Table 13: Clock Input Operating Conditions

0°C £ TA £ +70°C; VDDQ = +2.5V ±0.2V, VDD = +2.5V ±0.2V

Notes: 1–5, 15, 16, 30; notes appear on pages 59–62

PARAMETER/CONDITION SYMBOL MIN MAX UNITS NOTES

Clock Input Midpoint Voltage; CK and CK# VMP(DC)1.15 1.35 V 6, 9

Clock Input Voltage Level; CK and CK# VIN(DC)-0.3 VDDQ + 0.3 V6

Clock Input Differential Voltage; CK and CK# VID(DC)0.36 VDDQ + 0.6 V6, 8

Clock Input Differential Voltage; CK and CK# VID(AC)0.7 VDDQ + 0.6 V8

Clock Input Crossing Point Voltage; CK and CK# VIX(AC) 0.5 x VDDQ - 0.2 0.5 x VDDQ + 0.2 V9

CK#

2.80V

Maximum Clock Level

Minimum Clock Level

- 0.30V

1.25V

1.45V

1.05V VID (AC)

VID (DC)

VMP (DC) VIX (AC)

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

Table 14: Capacitance (x4, x8 TSOP)

Note: 13; notes appear on pages 59–62

PARAMETER SYMBOL MIN MAX UNITS NOTES

Delta Input/Output Capacitance: DQ0–DQ3 (x4), DQ0–DQ7 (x8) DCIO –0.50pF 24

Delta Input Capacitance: Command and Address DCI1–0.50pF 29

Delta Input Capacitance: CK, CK# DCI2–0.25pF 29

Input/Output Capacitance: DQs, DQS, DM CIO 4.0 5.0 pF

Input Capacitance: Command and Address CI12.0 3.0 pF

Input Capacitance: CK, CK# CI22.0 3.0 pF

Input Capacitance: CKE CI32.0 3.0 pF

Table 15: Capacitance (x4, x8 FBGA)

Note: 13; notes appear on pages 59–62

PARAMETER SYMBOL MIN MAX UNITS NOTES

Delta Input/Output Capacitance: DQs, DQS, DM DCIO –0.50pF 24

Delta Input Capacitance: Command and Address DCI1–0.50pF 29

Delta Input Capacitance: CK, CK# DCI2–0.25pF 29

Input/Output Capacitance: DQs, DQS, DM CIO 3.5 4.5 pF

Input Capacitance: Command and Address CI11.5 2.5 pF

Input Capacitance: CK, CK# CI21.5 2.5 pF

Input Capacitance: CKE CI31.5 2.5 pF

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

Table 16: Capacitance (x16 TSOP)

Note: 13; notes appear on pages 59–62

PARAMETER SYMBOL MIN MAX UNITS NOTES

Delta Input/Output Capacitance: DQ0–DQ7, LDQS, LDM DCIOL –0.50pF 24

Delta Input/Output Capacitance: DQ8–DQ15, UDQS, UDM DCIOU –0.50pF 24

Delta Input Capacitance: Command and Address DCI1–0.50pF 29

Delta Input Capacitance: CK, CK# DCI2–0.25pF 29

Input/Output Capacitance: DQ, LDQS, UDQS, LDM, UDM CIO 4.0 5.0 pF

Input Capacitance: Command and Address CI12.0 3.0 pF

Input Capacitance: CK, CK# CI22.0 3.0 pF

Input Capacitance: CKE CI32.0 3.0 pF

Table 17: Capacitance (x16 FBGA)

Note: 13; notes appear onpages 59–62

PARAMETER SYMBOL MIN MAX UNITS NOTES

Delta Input/Output Capacitance: DQ0–DQ7, LDQS, LDM DCIOL –0.50pF 24

Delta Input/Output Capacitance: DQ8–DQ15, UDQS, UDM DCIOU –0.50pF 24

Delta Input Capacitance: Command and Address DCI1–0.50pF 29

Delta Input Capacitance: CK, CK# DCI2–0.25pF 29

Input/Output Capacitance: DQ, LDQS, UDQS, LDM, UDM CIO 3.5 4.5 pF

Input Capacitance: Command and Address CI11.5 2.5 pF

Input Capacitance: CK, CK# CI21.5 2.5 pF

Input Capacitance: CKE CI31.5 2.5 pF

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

Table 18: IDD Specificat io ns and Condit io n s (x4, x8 ; -6/ -6R /-6T/-75E)

0°C £ TA £ +70°C; VDDQ = +2.5V ±0.2V, VDD = +2.5V ±0.2V

Notes: 1–5, 10, 12, 14, 47; notes appear on pages 59–62; See also Table 22, IDD Test Cycle Times, on page 55

MAX

PARAMETER/CONDITION SYMBOL -6R -6/6T -75E UNITS NOTES

OPERATING CURRENT: One bank; active precharge;

tRC = tRC (MIN); tCK = tCK (MIN); DQ, DM, and DQS inputs

changing on ce per c lock cycle; addres s and control inputs changing

once every two clock cycles

IDD0155 125 125 mA 22, 48

OPERATING CURRENT: One bank; active-read precharge;

burst = 4; tRC = tRC (MIN); tCK = tCK (MIN); I OUT = 0mA; address

and cont rol inputs changing once per clock cycle

IDD1210 170 160 mA 22, 48

PRECHARGE POWER-DOWN ST ANDBY CURRENT: All bank s idle;

power-down mode; tCK = tCK (MIN); CKE = (LOW) IDD2P 5 4 4 mA 23, 32, 50

IDLE STANDBY CURRENT: CS# = HIGH; all banks are idle;

tCK = tCK (MIN); CKE = HIGH; address and other control inputs

changing once per clock cycle; VIN = VREF for DQ, DQS, and DM

IDD2F 50 50 45 mA 51

ACTIVE POWER-DOWN STANDBY CURRENT: O ne bank active;

power-down mode; tCK = tCK (MIN); CKE = LOW IDD3P 40 30 25 mA 23, 32, 50

ACTIVE STANDBY CURRENT: CS# = HIGH; CKE = HIGH;

one bank active; tRC = tRAS (MAX); tCK = tCK (MIN); DQ, DM, and

DQS inputs changing twice per clock cycle; address and other

control inputs changing once per clock cycle

IDD3N 60 60 50 mA 22

OPERATING CURRENT: Burst = 2; READs; continuous burst;

one bank active; address and control inputs changing once per

clock cycle; tCK = tCK (MIN); IOUT = 0mA

IDD4R 215 175 150 mA 22, 48

OPERATING CURRENT: Burst = 2; WRITEs; continuous burst;

one bank active; address and control inputs changing once per

clock cycle; tCK = tCK (MIN); DQ, DM, and DQS inputs changing

twice per clock cycle

IDD4W 235 155 135 mA 22

AUTO REFRESH BURST CURRENT: tRC = tREFC (MIN) IDD5264 255 235 mA 50

tREFC = 7.8µs IDD5A 6 6 6 mA 27, 50

SELF REFRESH CURRENT: CKE £ 0.2V Standard IDD6544mA 11

Low power (L) IDD6A N/A 2 2 mA 11

OPERATING CURRENT: Four-bank interleaving READs

(Burst = 4) with auto precharge, tRC = minimum tRC allowed;

tCK = tCK (MIN); address and control inputs change only during

active READ or WRITE commands

IDD7470 405 350 mA 22, 49

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

Table 19: IDD Specificat io ns and Condit io n s (x4, x8 ; -75Z/ -75)

0°C £ TA £ +70°C; VDDQ = +2.5V ±0.2V, VDD = +2.5V ±0.2V

Notes: 1–5, 10, 12, 14, 47; notes appear on pages 59–62; See also Table 22, IDD Test Cycle Times, on page 55

MAX

PARAMETER/CONDITION SYMBOL -75Z -75 UNITS NOTES

OPERATING CURRENT: One bank; active precharge;

tRC = tRC (MIN); tCK = tCK (MIN); DQ, DM, and DQS inputs

changing on ce per c lock cycle; addres s and control inputs changing

once every two clock cycles

IDD0105 120 mA 22, 48

OPERATING CURRENT: One bank; active-read precharge;

burst = 4; tRC = tRC (MIN); tCK = tCK (MIN); IOUT = 0mA; address

and cont rol inputs changing once per clock cycle

IDD1145 155 mA 22, 48

PRECHARGE POWER-DOWN STANDBY CURRENT: All banks idle;

power-down mode; tCK = tCK (MIN); CKE = (LOW) IDD2P 4 4 mA 23, 32, 50

IDLE STANDBY CURRENT: CS# = HIGH; all banks are idle;

tCK = tCK (MIN); CKE = HIGH; address and other control inputs

changing once per clock cycle; VIN = VREF for DQ, DQS, and DM

IDD2F 45 45 mA 51

ACTIVE POWER-DOWN STANDBY CURRENT: O ne bank active;

power-down mode; tCK = tCK (MIN); CKE = LOW IDD3P 25 30 mA 23, 32, 50

ACTIVE STANDBY CURRENT: CS# = HIGH; CKE = HIGH;

one bank active; tRC = tRAS (MAX); tCK = tCK (MIN); DQ, DM, and

DQS inputs changing twice per clock cycle; address and other

control inputs changing once per clock cycle

IDD3N 50 50 mA 22

OPERATING CURRENT: Burst = 2; READs; continuous burst;

one bank active; address and control inputs changing once per

clock cycle; tCK = tCK (MIN); IOUT = 0mA

IDD4R 150 175 mA 22, 48

OPERATING CURRENT: Burst = 2; WRITEs; continuous burst;

one bank active; address and control inputs changing once per

clock cycle; tCK = tCK (MIN); DQ, DM, and DQS inputs changing

twice per clock cycle

IDD4W 135 190 mA 22

AUTO REFRESH BURST CURRENT: tRC = tREFC(MIN) IDD5235 245 mA 50

tREFC = 7.8µs IDD5A 6 6 mA 27, 50

SELF REFRESH CURRENT: CKE £ 0.2V Standard IDD644 mA 11

Low power (L) IDD6A 22 mA 11

OPERATING CURRENT: Four-bank interleaving READs

(Burst = 4) with auto precharge, tRC = minimum tRC allowed;

tCK = tCK (MIN); address and control inputs change only during

active READ or WRITE commands

IDD7350 365 mA 22, 49

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

Table 20: IDD Specificat io ns and Condit io ns (x16; -6/-6R/-6T/-75E)

0°C £ TA £ +70°C; VDDQ = +2.5V ±0.2V, VDD = +2.5V ±0.2V

Notes: 1–5, 10, 12, 14, 47; notes appear on pages 59–62; See also Table 22, IDD Test Cycle Times, on page 55

MAX

PARAMETER/CONDITION SYMBOL -6R -6/6T -75E UNITS NOTES

OPERATING CURRENT: One bank; active precharge;

tRC = tRC (MIN); tCK = tCK (MIN); DQ, DM, and DQS inputs

changing o nce per clock cycle ; address and control inputs changi ng

once every two clock cycles

IDD0155 125 125 mA 22, 48

OPERATING CURRENT: One bank; active-read precharge;

burst = 4; tRC = tR C (M IN ); tCK = tCK (MIN); IOUT = 0mA; address

and cont rol inputs changing once per clock cycle

IDD1210 180 170 mA 22, 48

PRECHARGE POWER-DOWN ST ANDBY CURRENT: All banks idle;

power-down mode; tCK = tCK (MIN); CKE = (LOW) IDD2P 5 4 4 mA 23, 32, 50

IDLE STANDBY CURRENT: CS# = HIGH; all banks are idle;

tCK = tCK (MIN); CKE = HIGH; address and other control inputs

changing once per clock cycle; VIN = VREF for DQ, DQS, and DM

IDD2F 50 50 45 mA 51

ACTIVE POWER-DOWN STANDBY CURRENT: O ne bank active;

power-down mode; tCK = tCK (MIN); CKE = LOW IDD3P 35 30 25 mA 23, 32, 50

ACTIVE STANDBY CURRENT: CS# = HIGH; CKE = HIGH;

one bank active; tRC = tRAS (MAX); tCK = tCK (MIN); DQ, DM, and

DQS inputs changing twice per clock cycle; address and other

control inputs changing once per clock cycle

IDD3N 60 60 50 mA 22

OPERATING CURRENT: Burst = 2; READs; continuous burst;

one bank active; address and control inputs changing once per

clock cycle; tCK = tCK (MIN); IOUT = 0mA

IDD4R 225 220 185 mA 22, 48

OPERATING CURRENT: Burst = 2; WRITEs; continuous burst;

one bank active; address and control inputs changing once per

clock cycle; tCK = tCK (MIN); DQ, DM, and DQS inputs changing

twice per clock cycle

IDD4W 250 165 145 mA 22

AUTO REFRESH BURST CURRENT: tRC = tREFC (MIN) IDD5265 255 235 mA 50

tREFC = 7.8µs IDD5A 866mA27, 50

SELF REFRESH CURRENT: CKE £ 0.2V St a ndard IDD6544mA 11

Low power (L) IDD6A NA 2 2 mA 11

OPERATING CURRENT: Four-bank interleaving READs

(Burst = 4) with auto precharge, tRC = minimum tRC allowed;

tCK = tCK (MIN); address and control inputs change only during

active READ or WRITE commands

IDD7480 440 380 mA 22, 49

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

Table 21: IDD Specificat io ns and Conditions (x16; -75Z/-75)

0°C £ TA £ +70°C; VDDQ = +2.5V ±0.2V, VDD = +2.5V ±0.2V

Notes: 1–5, 10, 12, 14, 47; notes appear on pages 59–62; See also Table 22, IDD Test Cycle Times, on page 55

MAX

PARAMETER/CONDITION SYMBOL -75Z -75 UNITS NOTES

OPERATING CURRENT: One bank; active precharge;

tRC = tRC (M IN); tCK = tCK (MI N); DQ, DM , and DQS inputs c hanging

once per clock cycle; address and control inputs changing once every

two clock cycles

IDD0105 120 mA 22, 48

OPERATING CURRENT: One bank; active-read precharge;

burst = 4; tRC = tRC (MIN); tCK = tCK (MIN); IOUT = 0mA; address

and cont rol inputs changing once per clock cycle

IDD1155 165 mA 22, 48

PRECHARGE POWER-DOWN STANDBY CURRENT: All banks idle;

power-down mode; tCK = tCK (MIN); CKE = (LOW) IDD2P 4 4 mA 23, 32, 50

IDLE STANDBY CURRENT: CS# = HIGH; all banks are idle;

tCK = tCK (MIN); CKE = HIGH; address and other control inputs

changing once per clock cycle; VIN = VREF for DQ, DQS, and DM

IDD2F 45 45 mA 51

ACTIVE POWER-DOWN STANDBY CURRENT: O ne bank active;

power-down mode; tCK = tCK (MIN); CKE = LOW IDD3P 25 30 mA 23, 32, 50

ACTIVE STANDBY CURRENT: CS# = HIGH; CKE = HIGH;

one bank active; tRC = tRAS (MAX); tCK = tCK (MIN); DQ, DM, and

DQS inputs changing twice pe r clock cycle; address and other control

inputs changing once per clock cycle

IDD3N 50 50 mA 22

OPERATING CURRENT: Burst = 2; READs; continuous burst;

one bank ac tive; address an d control in puts chan ging once pe r clock

cycle; tCK = tCK (MIN); IOUT = 0mA

IDD4R 185 250 mA 22, 48

OPERATING CURRENT: Burst = 2; WRITEs; continuous burst;

one ba nk active; ad dress and control inputs changing o nce per clock

cycle; tCK = tCK (MIN); DQ, DM, and DQS inputs changing twice per

clock cycle

IDD4W 145 250 mA 22

AUTO REFRESH BURST CURRENT: tRC = tREFC (MIN) IDD5235 245 mA 50

tREFC = 7.8µs IDD5A 6 6 mA 27, 50

SELF REFRESH CURRENT: CKE £ 0.2V Standard IDD644mA 11

Low power (L) IDD6A 22mA 11

OPERATING CURRENT: Four-bank interleaving READs

(Burst = 4) with auto precharge, tRC = minimum tRC allowed;

tCK = tCK (MIN); address and control inputs change only during

active READ or WRITE commands

IDD7380 400 mA 22, 49

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

Table 22: IDD Test Cycle Times

Values reflect number of clock cycles for each test.

IDD TEST SPEED

GRADE CLOCK

CYCLE TIME tRRD tRCD tRAS tRP tRC tRFC tREFI CL

IDD0-75/75Z 7.5ns NA NA 6 3 9 NA NA NA

-75E 7.5ns NA NA 6 2 8 NA NA NA

-6/6T/6R 6ns NA NA 7 3 10 NA NA NA

IDD1-75 7.5ns NA NA 6 3 9 NA NA 2.5

-75Z 7.5ns NA NA 6 3 9 NA NA 2

-75E 7.5ns NA NA 6 2 8 NA NA 2

-6/6T/6R 6ns NA NA 7 3 10 NA NA 2.5

IDD4R -75 7.5ns NA 3 NA NA NA NA NA 2.5

-75Z 7.5ns NA 3 NA NA NA NA NA 2

-75E 7.5ns NA 2 NA NA NA NA NA 2

-6/6T/6R 6ns NA 3 NA NA NA NA NA 2.5

IDD4W -75 7.5ns NA 3 NA NA NA NA NA NA

-75Z 7.5ns NA 3 NA NA NA NA NA NA

-75E 7.5ns NA 2 NA NA NA NA NA NA

-6/6T/6R 6ns NA 3 NA NA NA NA NA NA

IDD5-75/75Z 7.5ns NA NA NA 3 NA 10 NA NA

-75E 7.5ns NA NA NA 2 NA 9 NA NA

-6/6T/6R 6ns NA NA NA 3 NA 12 NA NA

IDD5A -75/75Z 7.5ns NA NA NA 3 NA NA 1,030 NA

-75E 7.5ns NA NA NA 2 NA NA 1,031 NA

-6/6T/6R 6ns NA NA NA 3 NA NA 1,288 NA

IDD7-75 7.5ns 2/4 3 NA 3 10 NA NA 2.5

-75Z 7.5ns 2/4 3 NA 3 10 NA NA 2

-75E 7.5ns 2 3 NA 2 8 NA NA 2

-6/6T/6R 6ns 2/4 3 NA 3 10 NA NA 2.5

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

Table 23: Electrical Characteristics and Recommended AC Operating Conditions

(-6/-6T/-6R/-75E)

Notes: 1–5, 14–17, 33, 46; notes appear on pages 59–62; 0°C £ TA £ +70°C; VDDQ = +2.5V ±0.2V, VDD = +2.5V ±0.2V

AC CHARACTERISTICS -6 (FBGA) -6T/ 6R (T SOP ) -75E

PARAMETER SYMBOL MIN MAX MIN MAX MIN MAX UNITS NOTES

Access window of DQs from CK/CK# tAC -0.70 +0.70 -0.70 +0.70 -0.75 +0.75 ns

CK hi gh-leve l width tCH 0.45 0.55 0.45 0.55 0.45 0.55 tCK 30

CK low-level width tCL 0.45 0.55 0.45 0.55 0.45 0.55 tCK 30

Clock cycle t ime CL = 2.5 tCK (2.5) 6 13 6 13 7. 5 13 ns 45, 52

CL = 2 tCK (2) 7.5 13 7.5 13 7.5 13 ns 45, 52

DQ and DM input hold time relative to DQS tDH 0.45 0.45 0.5 ns 26, 31

DQ and DM input setup time relative to DQS tDS 0.45 0.45 0.5 ns 26, 31

DQ and DM input pulse widt h (for each input) tDIPW 1.75 1.75 1.75 ns 31

Access window of DQS from CK/CK# tDQSCK -0.6 +0.6 -0.6 +0.6 -0.75 +0.75 ns

DQS input high pulse width tDQSH 0.35 0.35 0.35 tCK

DQS input lo w pu lse width tDQSL 0.35 0.35 0.35 tCK

DQS–DQ skew, DQS to last DQ valid, per group, per access

tDQSQ 0.4 0.4 5 0 .5 ns 25, 26

WRITE command to first DQS latching transition tDQSS 0.75 1.25 0.75 1.25 0.75 1.25 tCK

DQS falling edge to C K ri si n g – setu p time tDSS 0.2 0.2 0.2 tCK

DQS falling edge from CK rising – hold time tDSH 0.2 0.2 0.2 tCK

Half clock perio d tHP tCH,tCL tCH,tCL tCH,tCL ns 34

Data-out high-impedance window from CK /C K# tHZ +0.7 +0.7 +0.75 ns 18,42

Data-out low-imp eda nce window from CK/CK# tLZ -0.7 -0.7 -0.75 ns 18,43

Address and contro l input hold time (fast slew ra te) tIHF0.75 0.75 0.90 ns

Address and control input setup time (fast slew rate) tISF0.75 0.75 0.90 ns

Address and control inpu t hold time (slow slew rate) tIHS0.8 0.8 1 ns 14

Ad dress and cont rol input setup time (slow slew rate) tISS0.8 0.8 1 ns 14

Address and Control input pulse width ( for eac h input ) tIPW 2.2 2.2 2.2 ns

LOAD MODE REGISTER command cycle time tMRD 12 12 15 ns

DQ–DQS hold, DQS to firs t DQ to go non-v alid, per access tQH tHP

-tQHS tHP

-tQHS ns 25, 26

Data hold skew factor tQHS 0.5 0.55 0.75 ns

ACTIVE to PRECHARGE command tRAS 42 70,000 42 70,000 40 120,000 ns 35

ACTIVE to READ with aut o precha rg e comm and tRAP 18 18 15 ns

ACTIVE to ACTIVE /AU TO REF RES H com m a nd pe riod tRC 60 60 60 ns

AUTO REFRES H com m a nd pe riod tRFC 72 72 75 ns 50

ACTIVE to READ or WRITE delay tRCD 18 18 15 ns

PREC HAR GE command period tRP 18 18 15 ns

DQS read preamb le tRPRE 0.9 1.1 0.9 1.1 0.9 1.1 tCK 42

DQS read pos tamble tRPST 0.4 0.6 0.4 0.6 0.4 0.6 tCK 18

ACTIVE bank a to ACTIVE bank b command tRRD 12 12 15 ns

DQS write preamble tWPRE 0.25 0.25 0.25 tCK

DQS write preamble setup time tWPRES 0 0 0 n s 20, 21

DQS write postamble tWPST 0.4 0.6 0.4 0.6 0.4 0.6 tCK 19

Write recovery time tWR 15 15 15 ns

Internal WRITE to READ command delay tWTR 1 1 1 tCK

Data valid output window (DVW) N/A tQH - tDQSQ tQH - tDQSQ tQH - tDQSQ ns 25

REFRESH t o REFRESH comma nd inte rv al tREFC 70.3 70.3 70.3 µs 23

Average per i odi c refresh interval tREFI 7.8 7.8 7.8 µs 23

Terminating voltage delay to VDD tVTD 0 0 0 ns

Exit SELF REFRESH to non-REA D command tXSNR 75 75 75 ns

Exit SELF REFRESH to READ command tXSRD 200 200 200 tCK

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

Table 24: Electrical Characteristics and Recommended AC Operating Conditions

(-75Z/-75)

Notes: 1–5, 14–17, 33, 46; notes appear on pages 59–62; 0°C £ TA £ +70°C; VDDQ = +2.5V ±0.2V, VDD = +2.5V ±0.2V

AC CHARACTERISTICS -75Z -75

PARAMETER SYMBOL MIN MAX MIN MAX UNITS NOTES

Access window of DQs from CK/CK# tAC -0.75 +0.75 -0.75 +0.75 ns

CK hi gh-leve l width tCH 0.45 0.55 0.45 0.55 tCK 30

CK low-level width tCL 0.45 0.55 0.45 0.55 tCK 30

Clock cycle t ime CL=2.5 tCK (2.5) 7.5 13 7 .5 13 ns 45, 52

CL=2 tCK (2) 7.5 13 10 13 ns 45, 52

DQ and DM input hold time relative to DQS tDH 0.50 0.50 ns 26, 31

DQ and DM input setup time relative to DQS tDS 0.50 0.50 ns 26, 31

DQ and DM input pulse widt h (for each input) tDIPW 1.75 1.75 ns 31

Access window of DQS from CK/CK# tDQSCK -0.75 +0.75 -0.75 +0.75 ns

DQS input high pulse width tDQSH 0.35 0.35 tCK

DQS input lo w pu lse width tDQSL 0.35 0.35 tCK

DQS–DQ skew, DQS to last DQ valid, per group, per access

tDQSQ 0 .5 0.5 ns 25 , 26

WRITE command to first DQS latching transition tDQSS 0.75 1.25 0.75 1.25 tCK

DQS falling edge to C K ri si n g – setu p time tDSS 0.20 0.20 tCK

DQS falling edge from CK rising – hold time tDSH 0.20 0.20 tCK

Half clock perio d tHP tCH,tCL tCH,tCL ns 34

Data-out high-impedance window from CK /C K# tHZ +0.75 +0.75 ns 18,42

Data-out low-imp eda nce window from CK/CK# tLZ -0.75 -0.75 ns 18,43

Address and contro l input hold time (fast slew ra te) tIHF0.90 0.90 ns

Address and control input setup time (fast slew rate) tISF0.90 0.90 ns

Address and control inpu t hold time (slow slew rate) tIHS11 ns14

Ad dress and cont rol input setup time (slow slew rate) tISS11 ns14

Address and Control input pulse width ( for eac h input ) tIPW 2.2 2.2 ns

LOAD MODE REGISTER command cycle time tMRD 15 15 ns

DQ–DQS hold, DQS to first DQ to go non-valid, per access tQH tHP

-tQHS tHP

-tQHS ns 25, 26

Data hold skew factor tQHS 0.75 0.75 ns

ACTIVE to PRECHARGE command tRAS 40 120,000 40 120,000 ns 35

ACTIVE to READ with aut o precha rg e comm and tRAP 20 20 ns

ACTIVE to ACTIVE /AU TO REF RES H com m a nd pe riod tRC 65 65 ns

AUTO REFRES H com m a nd pe riod tRFC 75 75 ns 50

ACTIVE to READ or WRITE delay tRCD 20 20 ns

PREC HAR GE command period tRP 20 20 ns

DQS read preamb le tRPRE 0.9 1.1 0.9 1.1 tCK 42

DQS read pos tamble tRPST 0.4 0.6 0.4 0.6 tCK 18

ACTIVE bank a to ACTIVE bank b command tRRD 15 15 ns

DQS write preamble tWPRE 0.25 0.25 tCK

DQS write preamble setup time tWPRES 0 0 ns 20, 21

DQS write postamble tWPST 0.4 0.6 0.4 0.6 tCK 19

Write recovery time tWR 15 15 ns

Internal WRITE to READ command delay tWTR 1 1 tCK

Data valid output window (DVW) N/A tQH - tDQSQ tQH - tDQSQ ns 25

REFRESH t o REFRESH comma nd inte rv al tREFC 70.3 70.3 µs 23

Average per i odi c refresh interval tREFI 7.8 7.8 µs 23

Terminating voltage delay to VDD tVTD 0 0 ns

Exit SELF REFRESH to non-REA D command tXSNR 75 75 ns

Exit SELF REFRESH to READ command tXSRD 200 200 tCK

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

Ta ble 25: Input Slew Rate Derating Values for Addresses and Commands

0°C £ TA £ +70°C; VDDQ = +2.5V ±0.2V, VDD = +2.5V ±0.2V

Notes: 14; notes appear on pages 59–62

SPEED SLEW RATE tIS tIH UNITS

-75/-75Z/-75E 0.50 V/ns £ Slew Rate < 1.0 V/ns 1.00 1 ns

-75/-75Z/-75E 0.40 V/ns £ Slew Rate < 0.5 V/ns 1.05 1 ns

-75/-75Z/-75E 0.30 V/ns £ Slew Rate < 0.4 V/ns 1.15 1 ns

Ta ble 26: Input Slew Rate Derating Values for DQ, DQS, and DM

0°C £ TA £ +70°C; VDDQ = +2.5V ±0.2V, VDD = +2.5V ±0.2V

Notes: 31; notes appear on pages 59-62

SPEED SLEW RATE TDS TDH UNITS

-75/-75Z/-75 E 0.50 V/ns £ Slew Rate < 1.0 V/ns 0.50 0.50 ns

-75/-75Z/-75 E 0.40 V/ns £ Slew Rate < 0.5 V/ns 0.55 0.55 ns

-75/-75Z/-75 E 0.30 V/ns £ Slew Rate < 0.4 V/ns 0.60 0.60 ns

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

Notes

1. All volta g es referenced to VSS.

2. Tests for AC timing, IDD, and electrical AC and DC

characteristics may be conducted at nominal ref-

er enc e/ s upp l y volta ge level s, but the related spec-

ifications and device operation are guaranteed for

the full voltage range specified.

3. Outputs (except for IDD measurements) measured

with equivalent load:

4. AC timing and IDD tests may use a VIL-to-VIH

swing of up to 1.5V in the test environment, but

input timing is still referenced to VREF (or to the

crossing poin t fo r CK/C K#) , and param eter speci-

fica ti ons are guara nteed for the sp ecifi ed AC input

levels under normal use conditions. The mini-

mum slew rate for the input signals used to test

the device is 1 V/ns in the range between VIL(AC)

and VIH(AC).

5. The AC and DC input level specifications are as

defined in the SSTL_2 standard (i.e., the receiver

will effectively switch as a result of the signal

crossing th e AC input level and will remain in th at

state as long as the signal does not ring back

above [below] the DC input LOW [HIGH] level).

6. VREF is expected to equal VDDQ/2 of the tra nsmi t-

ting devic e and to trac k variation s in the DC le vel

of the same. Peak-to-peak noise (noncommon

mode) on VREF may not exceed ±2 percent of the

DC value. Thus, from VDDQ/2, VREF is allowed

±25mV for DC error and an additional ±25mV for

AC noise. This measurement is to be taken at the

neares t VREF bypass capacitor.

7. VTT is not applied di r ect ly to the devi ce . VTT, a sys-

tem supply for signal termination resistors, is

expected to be set equal to VREF and must track

variations in the DC level of VREF.

8. VID is the magnitude of the difference between

the input level on CK and the inp ut level on CK#.

9. The value of VIX and VMP are expected to equal

VDDQ/2 of the transmitting device and must track

variations in the DC level of the same.

10. IDD is dependent on output loading and cycle

rates. Specified values are obtained with mini-

mum cycle times at CL = 2.5 for -6/-6T/-6R and -

75, and CL = 2 for -75E/-75Z speeds with the out-

puts open.

11. Enables on-chip refresh and address counters.

12. IDD specifications are tested after the device is

properly in itialize d and i s average d at the de fined

cycle rate.

13. This parameter is sampled. VDD = +2.5V±0.2V,

VDDQ = +2.5V±0.2V, VREF = VSS, f = 100 MHz, TA =

25°C, VOUT (DC) = VDDQ/2, VOUT (peak to peak) =

0.2V. DM input is grouped with I/O pins, r eflecting

that they are matched in loading.

14. For slew rates < 1 V/ns and ³ 0.5 V/ns. If slew rat e

is less than 0.5 V/ns, timing must be derated; tIS

has an addit ional 50ps per ea ch 100mV/ns reduc-

tion in slew rate from the 500mV/ns, while tIH is

unaffected. If the slew rate exceeds 4.5 V/ns, func-

tionality is uncertain. For -6, -6T, and -6R, slew

rates must be greater than or equal to 0.5V/ns.

15. The CK/CK# input reference level (for timing ref-

erenced to CK/CK#) is the point at which CK and

CK# cross; the input reference level for signals

other than CK/CK# is VREF.

16. Inputs are not recognized as vali d un ti l VREF stabi-

lizes. Once initialized, including Self-Refresh

mode, VREF must be powered within the specified

range. Exception: during the period before VREF

stabilizes, CKE 0.3 x VDDQ is recognized as LO W.

17. The output timing reference level, as measured at

the timing reference point indicated in Note 3, is

VTT.

18. tHZ and tLZ transitions occur in the same access

time windows as data valid transitions. These

para meters ar e not refer enced t o a spec ific v olt age

level, but specify when the device output is no

longer driving (HZ) or begins d riving (LZ).

19. The intent of the “Don’t Care” state after comple-

tion of the postamble is that the DQS-driven sig-

nal should either be HIGH, LOW, or High-Z and

that a ny sign al t ransiti on wi thin the inp ut s witch-

ing region must follow valid input requirements. If

DQS transitions HIGH, above DC VIH (MIN) then

it must not transition LOW, below DC VIH, prior t o

tDQSH (MIN).

20. This is not a device limit. The device will operate

with a negative value, but system performance

could be degraded due to bus turnaround.

21. It is recommended that DQS be valid (HIGH or

LOW) on or before the WRITE command. The

case shown (DQS going from High-Z to logic

LO W) applies when no WRITEs were previously in

progress on the bus. If a previous WRITE was in

Output

(VOUT)Reference

Point

50Ω

VTT

30pF

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

progress, DQS could be HIGH during this time,

depending on tDQSS.

22. tRC (MIN) or tRFC (MIN) for IDD measurements

is the smallest multiple of tCK that meets the

minimum absolute value for the respective

parameter. tRAS (M AX) for IDD mea sur ements is

the largest multiple of tCK that meets the maxi-

mum absolute value for tRAS.

23. The refresh period is 64ms. This equates to an

average refresh rate of 7.8125µs. However, an

AUTO REFRESH command must be asserted at

least once every 70.3µs; burst refreshing or post-

ing by the DRAM controller greater than eight

refresh cycl es i s not allowed.

24. The I/O cap acitance pe r DQS and DQ byte/group

will not differ by more than this maximum

amount for any given device.

25. The data valid window is derived by achieving

other specifications: tHP (tCK/2), tDQSQ, and

tQH (tQH = tHP - tQHS). The data valid wind ow

derates in direct proportion to the clock duty

cycle and a practical data valid window can be

derived. The clock is a llowed a m aximum duty-

cycle variation of 45/55, because functionality

is uncertain when operating beyond a 45/55

ratio. Figure 35, Derating Data Valid Window

(tQH - tDQSQ), shows data valid w indow derat-

ing curves for duty cycles ranging between 50/

50 and 45/55.

26. Referenced to each output group: x4 = DQS with

DQ0–DQ3; x8 = DQS with DQ0–DQ7; x16 = LDQS

with DQ0–DQ7; and UDQS with DQ8–DQ15.

27. This limit is actually a nominal value and does not

result in a fail value. CKE is HIGH during

REFRESH command period (tRFC [MIN]) else

CKE is LOW (i.e., during standby).

28. To maintain a valid level, the transitioning edge of

the input must:

a. S ustain a constant slew rate from the current

AC level through to the target AC level, VIL

(AC) or VIH (AC).

b. Reach at le ast the t arget AC level.

c. After the AC target level is reached, continue

to maintain at least the target DC level, VIL

(DC) or VIH (DC).

29. The Input capacitance per pin group will not dif-

fer by more than this maximum amount for any

given device.

30. CK and CK# input slew rate must be ³ 1V/ns

(³2V/ns if measured differentially).

31. DQ and DM input slew rates must not deviate

from DQS by more than 10 percent. If the DQ/

DM/DQS slew rate is less than 0.5 V/ns, timing

must be derated: 50ps must be added to tDS and

3.750 3.700 3.650 3.600 3.550 3.500 3.450 3.400 3.350 3.300 3.250

3.400 3.350 3.300 3.250 3.200 3.150 3.100 3.050 3.000 2.950 2.900

2.500 2.463 2.425 2.388 2.350 2.313 2.275 2.238 2.200 2.163 2.125

1.8

2.0

2.2

2.4

2.6

2.8

3.0

3.2

3.4

3.6

3.8

50/50 49.5/50.5 49/51 48.5/52.5 48/52 47.5/53.5 47/53 46.5/54.5 46/54 45.5/55.5 45/55

Clock Duty Cycle

—— -75 @ tCK = 10ns

—— -8 @ tCK = 10ns

—— -75 @ tCK = 7.5ns

—— -8 @ tCK = 8ns

Figure 35: Derating Data Valid Window (tQH - tDQSQ)

Examples are for speed grades through -75

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

tDH for each 0.1 V/n s reduction in slew rate. For -

6, -6T and -6R speed grades, slew rate must be

³0.5 V/ns. If slew rate exceeds 4 V/ns, functional-

ity is uncertain.

32. VDD must not vary more than four percent if CKE

is not ac tive while an y bank is active.

33. The clock is allowed up to ±150ps of jitter. Each

timing parameter is allowed to vary by the same

amount.

34. tHP (MIN) is the lesser of tCL minimum and tCH

minimum actually applied to the device CK and

CK# inputs, collectively during bank active.

35. READs and WRITEs with auto precharge are not

allowed to be issued until tRAS (MIN) can be satis-

fied prior to the internal PRECHARGE command

being issued.

36. Any positive glitch must be less than 1/3 of the

clock cycle and not more than +400mV or 2.9V,

whichever is le ss. Any negative glitc h must be les s

than 1/3 of the clock cycle and not exceed either

-300mV or 2.2V, whichever is more positive.

37. Nor ma l output drive curves:

a. The full variation in driver pull-down current

from minimum to maximum process, temper-

ature, and voltage will lie within the outer

bounding line s o f the V-I curve of Fi gure 36

b. The variation in driver pull-down current

within nomin al limits of voltage and tempera-

ture is expected, but not guaranteed, to lie

within the inner bounding lines of the V-I

curve of Figure 36.

c. The full variation in driver pull-up current

from minimum to maximum process, temper-

ature and voltage will lie within the outer

bounding lines of the V-I curve of Figure 37.

d. The variation in driver pull-up current within

nominal limits of voltage and temperature is

expected, but not guaranteed, to lie within the

inner bounding lines of the V-I curve of

Figure 37.

e. The full variation in the ratio of the maximum

to minimum pull-up and pull-down current

should be between 0.71 and 1.4, for device

drain-to-source voltages from 0.1V to 1.0V, and

at the same voltage and temperature. f) The

full variation in the ratio of the nominal pull-

up to pull-down current should be unity ±10

percent, for device drain-to-source voltages

from 0.1V to 1.0V.

38. Reduced output drive curves:

a. The full variation in driver pull-down current

from minimum to maximum process, temper-

ature, and voltage will lie within the outer

bounding lines of the V-I curve of Figure 38.

b. The variation in driver pull-down current

within nomin al limits of voltage and tempera-

ture is expected, but not guaranteed, to lie

within the inner bounding lines of the V-I

cur ve of Figure 38.

c. The full variation in driver pull-up current

from minimum to maximum process, temper-

ature and voltage will lie within the outer

bounding lines of the V-I curve of Figure 39.

d. The variation in driver pull-up current within

nominal limits of voltage and temperature is

expected, but not guaranteed, to lie within the

inner bounding lines of the V-I curve of

Figure 39.

Figure 36: Full Drive Pull-Down

Characteristics Figure 37: Full Dr ive Pull-Up

Characteristics

100

120

140

160

0.0 0.5 1.0 1.5 2.0 2.5

VOUT (V)

OUT

(mA )

-200

-180

-160

-140

-120

-100

-80

-60

-40

-20

0.0 0.5 1.0 1.5 2.0 2.5

Q - V

OUT

(V)

OUT

(mA)

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

Figure 38: Reduced Drive Pull-Down

Characteristics Figure 39: Reduced Drive Pull-Up

Characteristics

e. The full variation in the ratio of the maximum

to minimum pull-up and pull-down current

should be between 0.71 and 1.4 for device

drain-to-source voltages from 0.1V to 1.0V, and

at the same voltage and temperature.

f. The full variation in the ratio of the nominal

pull-up to pull-down current should be unity

±10 percent, for device drain-to-source volt-

ages from 0.1V to 1.0V.

39. The voltage levels used are derived from a mini-

mum VDD level and the referenced test load. In

practice, the voltage levels obtained from a

properly terminated bus will provide signifi-

cantly different voltage values.

40. VIH overshoot: VIH (MAX) = VDDQ + 1.5V for a

pulse width £ 3ns and the pulse width can not

be greater than 1/3 of the cycle rate. VIL under-

shoot: VIL (MIN) = -1.5V for a pulse width £ 3ns

and the pulse width can not be greater than 1/3

of the cycle rate.

41. VDD and VDDQ must track each other.

42. This maximum value is derived from the refer-

enced tes t l oad. In practice, the values obtained in

a typical terminated design may reflect up to

310ps less for tHZ (MAX) and the last DVW. tHZ

(MAX) will prevail over tDQSCK (MAX) + tRPST

(MAX) condition. tLZ (MIN) will prevail over

tDQSCK (MIN) + tRPRE (MAX) condition.

43. For slew rates of greater than 1 V/ns the (LZ) tran-

sition will st art about 31 0ps earlier.

44. During initi ali zation , VDDQ, VTT, and VREF must be

equal to or less than VDD + 0.3V. Alternatively, VTT

may be 1.35V maximu m during power-up, even if

VDD/VDDQ are 0V, provided a minimum of 42W of

series resistance is used between the VTT supply

and the inpu t pin.

45. The current Micron part operates below the slow-

est JEDEC operating frequency of 83 MHz. As

such, future die may not reflect this option.

46. For the -6R speed grade, the minimum allowed

VDD and VDDQ is 2.4V.

47. When an input signal is indicated to be HIGH or

LOW, it is defined as a steady state logic HIGH or

LOW.

48. Random addressing changing; 50 percent of data

changing at every transfer.

49. Random addressing changing; 100 percent of data

changing at every transfer.

50. CKE must be active (HIGH) during the entire time

a refresh command is executed. That is, from the

time the AUTO REFRESH command is registered,

CKE must be active at each rising clock edge, until

tRFC has been satisfied.

51. IDD2N specif ies th e DQ, DQ S and DM to be driven

to a valid HIGH or LOW logic level. IDD2Q is simi-

lar to IDD2F except IDD2Q specifies the address

and control inputs to remain stable. Although

IDD2F, IDD2N, and IDD2Q are similar, IDD2F is

“worst case.”

52. Whenever the operating frequency is altered, not

includi ng jitt er, the DLL is required to be reset fol-

lowed by 200 clock cycles before any READ com-

mand.

0.00.51.01.52.

VOUT (V)

OUT

(mA)

-80

-70

-60

-50

-40

-30

-20

-10

0.0 0.5 1.0 1.5 2.0 2.5

VDDQ - VOUT (V)

OUT

(mA)

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

NOTE:

The above characteristics are specified under best, worst, and nominal process variations/conditions.

Table 27: Normal Ou tp ut Drive Cha racteristics

VOLTAGE

(V)

PULL-DOWN CURRE NT (mA) PULL-UP CURRENT (mA)

NOMINAL

LOW NOMINAL

HIGH MINIMUM MAXIMUM NOMINAL

LOW NOMINAL

HIGH MINIMUM MAXIMUM

0.1 6.0 6.8 4.6 9.6 -6.1 -7.6 -4.6 -10.0

0.2 12.2 13.5 9.2 18.2 -12.2 -14.5 -9.2 -20.0

0.3 18.1 20.1 13.8 26.0 -18.1 -21.2 -13.8 -29.8

0.4 24.1 26.6 18.4 33.9 -24.0 -27.7 -18.4 -38.8

0.5 29.8 33.0 23.0 41.8 -29.8 -34.1 -23.0 -46.8

0.6 34.6 39.1 27.7 49.4 -34.3 -40.5 -27.7 -54.4

0.7 39.4 44.2 32.2 56.8 -38.1 -46.9 -32.2 -61.8

0.8 43.7 49.8 36.8 63.2 -41.1 -53.1 -36.0 -69.5

0.9 47.5 55.2 39.6 69.9 -43.8 -59.4 -38.2 -77.3

1.0 51.3 60.3 42.6 76.3 -46.0 -65.5 -38.7 -85.2

1.1 54.1 65.2 44.8 82.5 -47.8 -71.6 -39.0 -93.0

1.2 56.2 69.9 46.2 88.3 -49.2 -77.6 -39.2 -100.6

1.3 57.9 74.2 47.1 93.8 -50.0 -83.6 -39.4 -108.1

1.4 59.3 78.4 47.4 99.1 -50.5 -89.7 -39.6 -115.5

1.5 60.1 82.3 47.7 103.8 -50.7 -95.5 -39.9 -123.0

1.6 60.5 85.9 48.0 108.4 -51.0 -101.3 -40.1 -130.4

1.7 61.0 89.1 48.4 112.1 -51.1 -107.1 -40.2 -136.7

1.8 61.5 92.2 48.9 115.9 -51.3 -112.4 -40.3 -144.2

1.9 62.0 95.3 49.1 119.6 -51.5 -118.7 -40.4 -150.5

2.0 62.5 97.2 49.4 123.3 -51.6 -124.0 -40.5 -156.9

2.1 62.8 99.1 49.6 126.5 -51.8 -129.3 -40.6 -163.2

2.2 63.3 100.9 49.8 129.5 -52.0 -134.6 -40.7 -169.6

2.3 63.8 101.9 49.9 132.4 -52.2 -139.9 -40.8 -176.0

2.4 64.1 102.8 50.0 135.0 -52.3 -145.2 -40.9 -181.3

2.5 64.6 103.8 50.2 137.3 -52.5 -150.5 -41.0 -187.6

2.6 64.8 104.6 50.4 139.2 -52.7 -155.3 -41.1 -192.9

2.7 65.0 105.4 50.5 140.8 -52.8 -160.1 -41.2 -198.2

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

NOTE:

The above characteristics are specified under best, worst, and nominal process variations/conditions.

Table 28: Reduced Output Drive Characteristics

VOLTAGE

(V)

PULL-DOWN CURRE NT (mA) PULL-UP CURRENT (mA)

NOMINAL

LOW NOMINAL

HIGH MINIMUM MAXIMUM NOMINAL

LOW NOMINAL

HIGH MINIMUM MAXIMUM

0.1 3.4 3.8 2.6 5.0 -3.5 -4.3 -2.6 -5.0

0.2 6.9 7.6 5.2 9.9 -6.9 -7.8 -5.2 -9.9

0.3 10.3 11.4 7.8 14.6 -10.3 -12.0 -7.8 -14.6

0.4 13.6 15.1 10.4 19.2 -13.6 -15.7 -10.4 -19.2

0.5 16.9 18.7 13.0 23.6 -16.9 -19.3 -13.0 -23.6

0.6 19.9 22.1 15.7 28.0 -19.4 -22.9 -15.7 -28.0

0.7 22.3 25.0 18.2 32.2 -21.5 -26.5 -18.2 -32.2

0.8 24.7 28.2 20.8 35.8 -23.3 -30.1 -20.4 -35.8

0.9 26.9 31.3 22.4 39.5 -24.8 -33.6 -21.6 -39.5

1.0 29.0 34.1 24.1 43.2 -26.0 -37.1 -21.9 -43.2

1.1 30.6 36.9 25.4 46.7 -27.1 -40.3 -22.1 -46.7

1.2 31.8 39.5 26.2 50.0 -27.8 -43.1 -22.2 -50.0

1.3 32.8 42.0 26.6 53.1 -28.3 -45.8 -22.3 -53.1

1.4 33.5 44.4 26.8 56.1 -28.6 -48.4 -22.4 -56.1

1.5 34.0 46.6 27.0 58.7 -28.7 -50.7 -22.6 -58.7

1.6 34.3 48.6 27.2 61.4 -28.9 -52.9 -22.7 -61.4

1.7 34.5 50.5 27.4 63.5 -28.9 -55.0 -22.7 -63.5

1.8 34.8 52.2 27.7 65.6 -29.0 -56.8 -22.8 -65.6

1.9 35.1 53.9 27.8 67.7 -29.2 -58.7 -22.9 -67.7

2.0 35.4 55.0 28.0 69.8 -29.2 -60.0 -22.9 -69.8

2.1 35.6 56.1 28.1 71.6 -29.3 -61.2 -23.0 -71.6

2.2 35.8 57.1 28.2 73.3 -29.5 -62.4 -23.0 -73.3

2.3 36.1 57.7 28.3 74.9 -29.5 -63.1 -23.1 -74.9

2.4 36.3 58.2 28.3 76.4 -29.6 -63.8 -23.2 -76.4

2.5 36.5 58.7 28.4 77.7 -29.7 -64.4 -23.2 -77.7

2.6 36.7 59.2 28.5 78.8 -29.8 -65.1 -23.3 -78.8

2.7 36.8 59.6 28.6 79.7 -29.9 -65.8 -23.3 -79.7

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

Figure 40: x4, x8 Data Output Timing – tDQSQ, tQH, and Data Valid Window

NOTE:

1. DQ transitioning after DQS transition define tDQSQ window. DQS transitions at T2 and at T2n are “early DQS,” at T3,

“nomin al DQS,” and at T3n, “late DQS .”

2. For a x4, only two DQ apply.

3. tDQSQ is derived at each DQS clock edge and is not cumulative over time and begins with DQS transition and ends with

the last valid DQ transition.

4. tQH is derived from tHP: tQH = tHP - tQHS.

5. tHP is the lesser of tCL or tCH clock transition collectively when a bank is active.

6. The data valid window is derived for each DQS transitions and is defined as tQH minus tDQSQ.

DQ (Last data valid)

DQ2

DQS1

DQ (Last data valid)

DQ (First data no longer valid)

All DQ and DQS, collectively6

Earliest signal transition

Latest signal transition

T2n

T3n

CK#

T1 T2 T3 T4T2n T3n

tQH

tHP

tQH

tHP

tQH

tDQSQ

Data

Valid

window

Data

Valid

window

Data

Valid

window

Data

Valid

window

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

Figure 41: x16 Data Output Timing – tDQSQ, tQH, and Data Valid Window

NOTE:

1. DQ transitioning after DQS transition define tDQSQ window. LDQS defines the lower byte and UDQS defines the upper

byte.

2. DQ0, DQ1, DQ2, DQ3, DQ4, DQ5, DQ6, or DQ7.

3. tDQSQ is derived at each DQS clock edge and is not cumulative over time and begins with DQS transition and ends with

the last valid DQ transition.

4. tQH is derived from tHP: tQH = tHP - tQHS.

5. tHP is the lesser of tCL or tCH clock transition collectively when a bank is active.

6. The data valid window is derived for each DQS transition and is tQH minus tDQSQ.

7. DQ8, DQ9, DQ10, D11, DQ12, DQ13, DQ14, or DQ15.

DQ (Last data valid)

LDQS

DQ (Last data valid)

DQ (First data no longer valid)

DQ0 - DQ7 and LDQS, collectively

T2n

T3n

CK#

T1 T2 T3 T4T2n T3n

tQH

tDQSQ

Data Valid

window Data Valid

window

DQ (Last data valid)

UDQS

DQ (Last data valid)

DQ (First data no longer valid)

DQ8 - DQ15 and UDQS, collectively

T2n

T3n

tQH

tDQSQ

tHP

tQH

Data Valid

window

Data Valid

window Data Valid

window

Upper Byte

Lower Byte

Data Valid

window

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

Figure 42: Data Output Timing – tAC and tDQSCK

NOTE:

1. tDQSCK is the DQS output window relative to CK and is the “long-term” component of DQS skew.

2. DQ transitioning after DQS transition define tDQSQ window.

3. All DQ must transition by tDQSQ after DQS transitions, regardless of tAC.

4. tAC is the DQ output window relative to CK, and is the “long-term” component of DQ skew.

5. tLZ (MIN) and tAC (MIN) are the first valid signal transition.

6. tHZ (MAX),and tAC (MAX) are the latest valid signal transition.

7. READ command with CL = 2 issued at T0.

CK#

DQS, or LDQS/UDQS

T1 T2 T3 T4 T5

T2n T3n T4n T5n T6

tRPST

tLZ (MIN)

tDQSCK

(MAX)

tDQSCK

(MIN) tDQSCK

(MAX)

tDQSCK

(MIN)

tHZ(MAX)

tRPRE

DQ (Last data valid)

DQ (First data valid)

All DQ values, collectively

tAC

(MIN) tAC

(MAX)

tLZ (MIN) tHZ (MAX)

T2n T3n T4n T5n

T2n

T3n

T4n

T5n

T2 T3 T4 T5

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

Figure 43: Data Input Timing

NOTE:

1. tDSH (MIN) generally occurs during tDQSS (MIN).

2. tDSS (MIN) generally occurs during tDQSS (MAX).

3. WRITE command issued at T0.

4. For x16, LDQS controls the lower byte and UDQS controls the upper byte.

DQS

tDQSS

tDQSH tWPST

tDH

tDS

tDQSL

tDSS2tDSH1

tDSH1tDSS2

CK# T0

T1 T1n T2 T2n T3

DON’T CARE

TRANSITIONING DATA

WPRE

WPRES

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

Figur e 44: Initialize and Load Mode Registers

NOTE:

1. VTT is not applied directly to the device; however, tVTD should be greater than or equal to zero to avoid device latch-up. VDDQ, VTT, and VREF

must be equal to or less than VDD + 0.3V. Alternatively, VTT may be 1.35V maximum during power-up, even if VDD/VDDQ are 0V, pr o vided a

minimum of 42

of series resistance is used between the VTT supply and the input pin. Once initialized, VREF must alw ays be powered within

the specified range.

2. Reset the DLL wi th A8 = H w h i le p rogram ming the operat i n g pa r a m eters .

3. tMRD is required before any command can be applied, and 200 cycles of CK are required before a READ command can be issued.

4. The two AUTO REFRESH commands at Td0 and Te0 may be applied prior to the LOAD MODE REGISTER (LMR) command at Ta0.

5. Although not required by the Micr on de vice, JEDEC specifies issuing anoth er LMR command (A8 = L) prior to activating any

bank. If ano ther LMR command is is su ed , the same opera ting para meters must be us ed as pr eviously issued.

6. PRE = PRECHARGE command; LMR = LOAD MODE REGISTER command; AR = AUTO REFRESH command; ACT = ACTIVE com-

mand; RA = Row Addr es s; and BA = Bank Address.

VTD

CKE LVCMOS

LOW LEVEL

BA0, BA1

200 cycles of CK

Load Extended

Mode Register Load Mode

tMRD tMRD tRP tRFC tRFC

Power-up: V

and CK stable

T = 200µs

High-Z

DQS High-Z

A0-A9,

A11, A12

A10

ALL BANKS

CK#

VTT

VREF

VDD

VDDQ

COMMAND6LMRNOP PRELMR AR AR ACT

tIS tIH

BA0 = H,

BA1 = L

tIS tIH

BA0 = L,

BA1 = L

tIS tIH

()()

CODE CODE

tIS tIH

CODE CODE

PRE

ALL BANKS

tIS tIH

T0 T1 Ta0 Tb0 Tc0 Td0 Te0 Tf0

()()

DON’T CARE

(

)(

)

()()

(

)(

)

(

)(

)

(

)(

)

(

)()

(

)()

()()

()(

)

()(

)

(

)(

)

(

)(

)

tRP

()()

-6/6T/6T -75E/75Z -75

SYMBOL MIN MAX MIN MAX MIN MAX UNITS

tCH 0.45 0.55 0.45 0.55 0.45 0.55 tCK

tCL 0.45 0.55 0.45 0.55 0.45 0.55 tCK

tCK (2.5) 6 13 7.5 13 7.5 13 ns

tCK (2) 7. 5 13 7.5 13 10 13 n s

tIHF.75 .90 0.90 ns

tISF.75 .90 0.90 ns

tIHS0.8 1 1 ns

tISS0.8 1 1 ns

tMRD 15 15 15 ns

tRFC 72 75 75 ns

tRP 18 15 20 ns

tVTD 0 0 0 ns

-6/6T/6T -75E/75Z -75

SYMBOL MIN MAX MIN MAX MIN MAX UNITS

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

Figure 45: Power-Down Mode

NOTE:

1. Once initialized, VREF must always be powered within the specified range.

2. If this command is a PRECHARGE (or if the device is already in the idle state), then the power-down mode shown is pre-

charge power-down. If this command is an ACTIVE (or if at least one row is already active), then the power-down mode

shown is active power-down.

3. No column accesses are allowed to be in progres s at the time power-d own is entered.

CK#

COMMAND VALID2NOP

ADDR

CKE1

DQS

VALID

Enter

Power-Down

Mode

Exit

Power-Down

Mode

REFC

()()

T0 T1 Ta0 Ta1 Ta2T2

NOP

DON’T CARE

()()

VALIDVALID

-6/6T/6T -75E/75Z -75

SYMBOL MIN MAX MIN MAX MIN MAX UNITS

tCH 0.45 0.55 0.45 0.55 0.45 0.55 tCK

tCL 0.45 0.55 0.45 0.55 0.45 0.55 tCK

tCK (2.5) 6 13 7.5 13 7.5 13 ns

tCK (2) 7.5 13 7.5 13 10 13 ns

tIHS0.8 1 1 ns

tISS0.8 1 1 ns

-6/6T/6T -75E/75Z -75

SYMBOL MIN MAX MIN MAX MIN MAX UNITS

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

Figure 46: Au to Refresh Mode

NOTE:

1. PRE = PRECHARGE; ACT = ACTIVE; AR = AUTO REFRESH; RA = Row Address; and BA = Bank Address.

2. NOP commands are shown for ease of illustration; other valid commands may be possible at these times. CKE must be

active during clock positive transitions.

3. NOP or COMMAND INHIBIT are the only commands allowed until after tRFC time; CKE must be active during clock posi-

tive transitions.

4. “Don’t Care” if A10 is HIGH at this point; A10 must be HIGH if more than one bank is active (i.e., must precharge all

active banks).

5. DM, DQ, and DQS signals are all “Don’t Care”/High-Z for operations shown.

6. The second AUTO REFRESH is not required and is only shown as an example of two back-to-back AUTO REFRESH com-

mands.

CK#

COMMAND

1NOP2

VALID VALID

NOP 2NOP2

PRE

CKE

A0-A9,

A11, A12

A10

BA0, BA1

1Bank(s)4BA

AR NOP2, 3 AR6NOP2, 3 ACTNOP2

ONE BANK

ALL BANKS

DQS

tRFC

tRP tRFC

T0 T1 T2 T3 T4 Ta0 Tb0

Ta1 Tb1 Tb2

DON’T CARE

()()

-6/6T/6T -75E/75Z -75

SYMBOL MIN MAX MIN MAX MIN MAX UNITS

tCH 0.45 0.55 0.45 0.55 0.45 0.55 tCK

tCL 0.45 0.55 0.45 0.55 0.45 0.55 tCK

tCK (2.5) 6 13 7.5 13 7.5 13 ns

tCK (2) 7. 5 13 7.5 13 10 13 n s

tIHF0.75 0.90 0.90 ns

tISF0.75 0.90 0.90 ns

tIHS0.8 1 1 ns

tISS0.8 1 1 ns

tRFC 72 75 75 ns

tRP 18 15 20 ns

-6/6T/6T -75E/75Z -75

SYMBOL MIN MAX MIN MAX MIN MAX UNITS

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

Figur e 47: Self Refresh Mode

NOTE:

1. Clock must be stable until after the SELF REFRESH command has been registered. A change in clock frequency is allowed before

Ta0, provided it is within the specified tCK limits. Regardless, the clock must be stable before exiting self refresh mode. That is,

the clock must be cycling within specifications by Ta0.

2. NOPs are interchangeable with DESELECT commands; AR = AUTO REFRESH command.

3. Auto refresh is not required at this point, but is highly recommended.

4. Device must be in the all banks idle state prior to entering self refresh mode.

XSNR is required before any non-READ command can be applied ; only NOP or DESELECT commands are allowed until Tb1.

XSRD (200 cycles of a valid CK and CKE = high) is required before an y READ command can be applied.

7. As a general rule, any time self refresh mode is exited, the DRAM may not re-enter the self refresh mode until all rows have

been refreshed via the AUTO REFRESH command at the distributed refresh rate,

REFI, or faster. However, self refresh mode

may be re-entered an ytime a fter exiting, if the followi ng conditions are all met:

a. The DRAM had been in the Self Refresh Mode for a minimum of 200ms prior to exiting.

b. tXSNR and tXSRD are not violated.

c. At least two AUTO REFRESH commands are performed during each tREFI interval while the DRAM remains out of

Self Refresh mode.

8. If the clock frequency is changed during self refresh mode, a DLL rese t is required upon exit.

9. Once initialized, VREF must always be powered within the specified range.

CK#

COMMAND

2NOP AR

ADDR

CKE

DQS

NOP

tRP

tCH tCL tCK

tIS

tIH

tIS tIH tIS

Enter Self Refresh Mode7Exit Self Refresh Mode7

T0 T11Ta1

()()

DON’T CARE

Ta0

tXSRD6

()()

NOP

VALID3VALID

()()

tXSNR5

()()

Ta2 Tb1 Tb2 Tc1

VALID VALID

VALID

tIS tIH

()()

VALID

()()

-6/6T/6T -75E/75Z -75

SYMBOL MIN MAX MIN MAX MIN MAX UNITS

tCH 0.45 0.55 0.45 0.55 0.45 0.55 tCK

tCL 0.45 0.55 0.45 0.55 0.45 0.55 tCK

tCK (2.5) 6 13 7.5 13 7.5 13 ns

tCK (2) 7. 5 13 7.5 13 10 13 n s

tIHF0.75 0.90 0.90 ns

tISF0.75 0.90 0.90 ns

tIHS0.8 1 1 ns

tISS0.8 1 1 ns

tRFC 72 75 75 ns

tRP 18 15 20 ns

tVTD 0 0 0 ns

-6/6T/6T -75E/75Z -75

SYMBOL MIN MAX MIN MAX MIN MAX UNITS

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

Figure 48: Bank Read - Without Auto Precharge

NOTE:

1. DOn = data-out from column n; subsequent elements are provided in the programmed order.

2. Burst length = 4 in the case shown.

3. Disable auto precharge.

4. “Don’t Care” if A10 is HIGH at T5.

5. PRE = PRECHARGE; ACT = ACTIVE; RA = Row Address; and BA = Bank Address.

6. NOP commands are shown for ease of illustration; other commands may be valid at these times.

7. The PRECHARGE command can only be applied at T5 if tRAS minimum is met.

8. Refer to Figure 40 on page 65, Figure 41 on page 66, and Figure 42 on page 67 for detailed DQS and DQ timing.

CK#

CKE

A10

BA0, BA1

tCK tCH tCL

tIS

tIH

tIS

tIH

tIS tIH

tRCD

tRAS7

tRC

tRP

CL = 2

T0 T1 T2 T3 T4 T5 T5n T6nT6 T7 T8

DQS

Case 1:

(

MIN)

and

DQSCK

(

MIN)

Case 2:

(

MAX)

and

DQSCK

(

MAX)

DQS

RPRE

tRPRE

tRPST

DQSCK

(

MIN)

DQSCK

(

MAX)

(

MIN)

(

MIN)

(

MIN)

(

MAX)

(

MAX)

NOP6

COMMAND

ACT

Col n

READ2PRE

Bank x

Bank xBank x4

ACT

Bank x

NOP6NOP6NOP6

ONE BANK

ALL BANKS

DON’T CARE TRANSITIONING DATA

x4: A0-A9, A11

x8: A0-A9

x16: A0-A8

x4: A12

x8: A11, A12

x16: A9, A11, A12

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

Figure 49: Bank Read - With Auto Precharge

NOTE:

1. DOn = data-out from column n; subsequent elements are provided in the programmed order.

2. Burst length = 4 in the case shown.

3. Enable auto precharge.

4. ACT = ACTIVE; RA = Row Address; and BA = Bank Address.

5. NOP commands are shown for ease of illustration; other commands may be valid at these times.

6. The READ command can only be applied at T3 if tRAP is satisf ied at T3.

7. tRP starts only after tRAS has been satisfied.

8. Refer to Figure 40 on page 65, Figure 41 on page 66, and Figure 42 on page 67 for detailed DQS and DQ timing.

CK#

CKE

A10

BA0, BA1

IS IH

RP7

CL = 2

T0 T1 T2 T3 T4 T5 T5n T6nT6 T7 T8

DQS

Case 1:

AC (

MIN)

and

DQSCK (

MIN)

Case 2:

(

MAX)

and

DQSCK

(

MAX)

DQS

RPRE

RPST

DQSCK

(

MIN)

DQSCK

(

MAX)

(

MIN)

(

MIN)

(

MAX)

(

MAX)

NOP5

COMMAND

ACT

Col n

READ2,6 NOP5

Bank x

ACT

Bank x

NOP5NOP5NOP5

DON’T CARE TRANSITIONING DATA

x4: A0-A9, A11

x8: A0-A9

x16: A0-A8

x4: A12

x8: A11, A12

x16: A9, A11, A12

tRAS

(

MIN)

tRCD, tRAP6

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

Figure 50: Bank W rite - Without Auto Precharge

NOTE:

1. DI n = data-in from column n; subsequent elements are provided in the programmed order.

2. Burst length = 4 in the case shown.

3. Disable auto precharge.

4. “Don’t Care” if A10 is HIGH at T8.

5. PRE = PRECHARGE; ACT = ACTIVE; RA = Row Address; and BA = Bank Address.

6. NOP commands are shown for ease of illustration; other commands may be valid at these times.

7. See Figure 43, Data Input Timing, on page 68, for detailed DQ timing.

8. Although not required by the Micron device, JEDEC specifies that DQS be a valid HIGH, LOW or some point on a valid

transition on or before this clock edge (T3n).

CK#

CKE

A10

BA0, BA1

tCK tCH tCL

tIS

tIH

tIS

tIH

tIS tIH

tRCD

tRAS tRP

tWR

T0 T1 T2 T3 T4 T5 T5n T6 T7 T8T4n

NOP6

COMMAND

ACT

Col n

WRITE2NOP6

ONE BANK

ALL BANKS

Bank x

PRE

Bank x

NOP6NOP6NOP6

tDQSL tDQSH tWPST

Bank x4

DQS

tDS tDH

DON’T CARE TRANSITIONING DATA

tDQSS (NOM)

WPRE

WPRES

x4: A0-A9, A11

x8: A0-A9

x16: A0-A8

x4: A12

x8: A11, A12

x16: A9, A11, A12

T3n

-6/6T/6T -75E/75Z -75

SYMBOL MIN MAX MIN MAX MIN MAX UNITS

tCH 0.45 0.55 0.45 0.55 0.45 0.55 tCK

tCL 0.45 0.55 0.45 0.55 0.45 0.55 tCK

tCK (2.5) 6 13 7.5 13 7.5 13 ns

tCK (2) 7. 5 13 7.5 13 10 13 n s

tIHF0.75 0.90 0.90 ns

tISF0.75 0.90 0.90 ns

tIHS0.8 1 1 ns

tISS0.8 1 1 ns

tMRD 15 15 15 ns

tRFC 72 75 75 ns

tRP 18 15 20 ns

tVTD 0 0 0 ns

-6/6T/6T -75E/75Z -75

SYMBOL MIN MAX MIN MAX MIN MAX UNITS

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

Figure 51: Bank Write - With Auto Precharge

NOTE:

1. DIn = data-out from column n; subsequent elements are provided in the programmed order.

2. Burst length = 4 in the case shown.

3. Enable auto precharge.

4. ACT = ACTIVE;, RA = Row Address; and BA = Bank Address.

5. NOP commands are shown for ease of illustration; other commands may be valid at these times.

6. See Figure 43, Data Input Timing, on page 68, for detailed DQ timing.

7. Although not required by the Micron device, JEDEC specifies that DQS be a valid HIGH, LOW or some point on a valid

transition on or before this clock edge (T3n).

CK#

CKE

A10

BA0, BA1

tCK tCH tCL

tIS

tIH

tIS

tIH

tIS tIH

tRCD

tRAS tRP

tWR

T0 T1 T2 T3 T4 T5 T5n T6 T7 T8T4n

NOP5

COMMAND

ACT

Col n

WRITE2NOP5

Bank x

NOP5

Bank x

NOP5NOP5NOP5

tDQSL tDQSH tWPST

DQS

tDQSS (NOM)

DON’T CARE TRANSITIONING DATA

WPRES

WPRE

x4: A0-A9, A11

x8: A0-A9

x16: A0-A8

x4: A12

x8: A11, A12

x16: A9, A11, A12

T3n

-6/6T/6T -75E/75Z -75

SYMBOL MIN MAX MIN MAX MIN MAX UNITS

tCH 0.45 0.55 0.45 0.55 0.45 0.55 tCK

tCL 0.45 0.55 0.45 0.55 0.45 0.55 tCK

tCK (2.5) 6 13 7.5 13 7.5 13 ns

tCK (2) 7.5 13 7.5 13 10 13 ns

tDH 0.45 0.5 0.5 ns

tDS 0.45 0.5 0.5 ns

tDQSH 0.35 0.35 0.35 tCK

tDQSL 0.35 0.35 0.35 tCK

tDQSS 0.75 1.25 0.75 1.25 0.75 1.25 tCK

tDSS 0.2 0.2 0.2 tCK

tDSH 0.2 0.2 0.2 tCK

tIHS0.8 1 1 ns

tISS0.8 1 1 ns

tRAS 42 70,000 40 120,000 40 120,000 ns

tRCD 18 15 20 ns

tRP 18 15 20 ns

tWPRE 0.25 0.25 0.25 tCK

tWPRES 000 ns

tWPST 0.4 0.6 0.4 0.6 0.4 0.6 tCK

tWR 15 15 15 ns

-6/6T/6T -75E/75Z -75

SYMBOL MIN MAX MIN MAX MIN MAX UNITS

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

Figure 52: Write – DM Operation

NOTE:

1. DIn = data-in from column n; subsequent elements are provided in the programmed order.

2. Burst length = 4 in the case shown.

3. Disable auto precharge.

4. “Don’t Care” if A10 is HIGH at T8.

5. PRE = PRECHARGE; ACT = ACTIVE; RA = Row Address; and BA = Bank Address.

6. NOP commands are shown for ease of illustration; other commands may be valid at these times.

7. See Figure 43, Data Input Timing, on page 68, for detailed DQ timing.

8. Although not required by the Micron device, JEDEC specifies that DQS be a valid HIGH, LOW or some point on a valid

transition on or before this clock edge (T3n).

CK#

CKE

A10

BA0, BA1

RCD

RAS tRP

tWR

T0 T1 T2 T3 T4 T5 T5n T6 T7 T8T4n

NOP6

COMMAND

ACT

Col n

WRITE2NOP6

ONE BANK

ALL BANKS

Bank x

PRE

Bank x

NOP6NOP6NOP6

DQSL

DQSH

WPST

Bank x4

DQS

DON’T CARE TRANSITIONING DATA

DQSS (NOM)

WPRES

WPRE

x4: A0-A9, A11

x8: A0-A9

x16: A0-A8

x4: A12

x8: A11, A12

x16: A9, A11, A12

T3n

-6/6T/6T -75E/75Z -75

SYMBOL MIN MAX MIN MAX MIN MAX UNITS

tCH 0.45 0.55 0.45 0.55 0.45 0.55 tCK

tCL 0.45 0.55 0.45 0.55 0.45 0.55 tCK

tCK (2.5) 6 13 7.5 13 7.5 13 ns

tCK (2) 7.5 13 7.5 13 10 13 ns

tDH 0.45 0.5 0.5 ns

tDS 0.45 0.5 0.5 ns

tDQSH 0.35 0.35 0.35 tCK

tDQSL 0.35 0.35 0.35 tCK

tDQSS 0.75 1.25 0.75 1.25 0.75 1.25 tCK

tDSS 0.2 0.2 0.2 tCK

tDSH 0.2 0.2 0.2 tCK

tIHS0.8 1 1 ns

tISS0.8 1 1 ns

tRAS 42 70,000 40 120,000 40 120,000 ns

tRCD 18 15 20 ns

tRP 18 15 20 ns

tWPRE 0.25 0.25 0.25 tCK

tWPRES 000 ns

tWPST 0.4 0.6 0.4 0.6 0.4 0.6 tCK

tWR 15 15 15 ns

-6/6T/6T -75E/75Z -75

SYMBOL MIN MAX MIN MAX MIN MAX UNITS

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

Figure 53: 66-Pin Plastic TSOP (400 mil)

NOTE:

1. All dimensionsare in millimeters.

2. Package width and length do not include mold protrusion; allowable mold protrusion is 0.25mm per side.

SEE DETAIL A

0.10

0.65 TYP 0.71

10.16 ±0.08

0.15

0.50 ±0.10

PIN #1 ID

DETAIL A

22.22 ± 0.08

0.32 ±0.075TYP

+0.03

-0.02

+0.10

-0.05

1.20 MAX 0.10

0.25

11.76 ±0.10

0.80 TYP

0.10 (2X)

GAGE PLANE

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M ic ron Te chnology, In c. , reserv es the right to cha ng e prod ucts or specifica tio ns without notice .

Figure 54: 60-Ball FBGA (16 x 9mm)

NOTE:

All dimensions are in millimeters.

BALL #1 ID

SOLDER BALL MATERIAL: EUTECTIC 63% Sn, 37% Pb or

62% Sn, 36% Pb, 2% Ag

SOLDER BALL PAD: Ø .33mm

MOLD COMPOUND: EPOXY NOVOLAC

SUBSTRATE: PLASTIC LAMINATE

BALL A1

BALL A1 ID

0.850 ±0.075

0.10 CC

.45

60X Ø

SOLDER BALL DIAMETER REFERS TO

POST REFLOW CONDITION. THE

PRE-REFLOW DIAMETER IS Ø 0.40mm.

BALL A9

11.00

5.50 ±0.05

8.00 ±0.05

16.00 ±0.10

1.00

TYP

0.80

TYP

6.40

3.20 ±0.05 4.50 ±0.05

9.00 ±0.10 1.20 MAX

SEATING PLANE

256Mb: x4, x8, x16

DDR SD RAM

09005aef8076894f M i cro n Technology, Inc., reserves the ri ght to change products or sp eci ficati on s wi tho ut notice..

8000 S. Federal Way, P.O. Box 6, Boise, ID 83707-0006, Tel: 208-368-3900

E-mail: prodmktg@micron.com, Interne t: http://www.m icron.com, Customer Comment Line: 800-932-4992

Micron, the M logo, and the Micron logo are trademarks and/or service marks of Micron Technology, Inc.

All other trademarks are the property of their respective owners.

Figure 55: 60-Ball FBGA (14 x 8mm)

NOTE:

All dimensions are in millimeters.

Data Sheet Designation

This data sheet contains minimum and maximum

limits specified over the complete power supply and

temperature range for production devices. Although

considered final, these specifications are subject to

change, as further product development and data

charac terization s o metime s occur.

PIN A1 ID

1.20 MAX

MOLD COMPOUND: EPOXY NOVOLAC

SUBSTRATE: PLASTIC LAMINATE

SOLDER BALL MATERIAL: EUTECTIC 62% Sn, 36% Pb, 2%Ag

SOLDER BALL PAD: Ø .33mm

14.00 ±0.10

BALL A1

BALL A9

PIN A1 ID

1.00 TYP

0.80 TYP

7.00 ±0.05

8.00 ±0.10

4.00 ±0.05

3.20 ±0.05

5.50 ±0.05

0.850 ±0.075

SEATING PLANE

11.00

6.40

0.10 C

60X ∅0.45

SOLDER BALL DIAMETER

REFERS TO POST REFLOW

CONDITION. THE PRE-

REFLOW DIAMETER IS Ø 0.40