REVISIONS
LTR DESCRIPTION DATE (YR-MO-DA) APPROVED
A
Changes in accordance with NOR 5962-R139-96.
96-06-06
M. A. FRYE
B
Replaced reference to MIL-STD-973 with reference to MIL-PRF-38535.
Deleted subgroups 10 and 11 in table II (not called out in table I). Drawing
updated to reflect current requirements. -rrp
04-01-27
R. MONNIN
THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED.
REV
SHEET
REV
SHEET
REV STATUS REV B B B B B B B B B B
OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10
PMIC N/A PREPARED BY
Charles E. Besore
DEFENSE SUPPLY CENTER COLUMBUS
STANDARD
MICROCIRCUIT
DRAWING
CHECKED BY
Charles E. Besore
COLUMBUS, OHIO 43216
http://www.dscc.dla.mil
THIS DRAWING IS AVAILABLE
FOR USE BY ALL
DEPARTMENTS
APPROVED BY
Michael Frye
MICROCI RCUIT, LINEAR, VOLTAGE
COMPARATOR, QUAD, PRECISI ON, MONOLITHIC
SILICON
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
DRAWING APPROVAL DATE
90-02-02
AMSC N/A
REVISION LEVEL
B SIZE
A CAGE CO DE
67268
5962-86860
SHEET
1 OF
10
DSCC FORM 2233
APR 97 5962-E082-04
DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.
STANDARD
MICROCI RCUIT DRAWING
SIZE
A
5962-86860
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000 REVISION LEVEL
B SHEET 2
DSCC FORM 2234
APR 97
1. SCOPE
1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in
accordance with MIL-PRF-38535, appendix A.
1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example:
5962-86860 01 E X
Drawing number
Device type
(see 1.2.1) Case outline
(see 1.2.2) Lead finish
(see 1.2.3)
1.2.1 Device type(s). The device type(s) identify the circuit function as follows:
Device type Generic number Circuit function
01 HA-4902 Precision quad comparator
1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows:
Outline letter Descriptive designator Terminals Package style
E GDIP1-T16 or CDIP2-T16 16 Dual-in-line
2 CQCC1-N20 20 Square leadless chip carrier
1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A.
1.3 Absolute maximum ratings.
Voltage between +V and –V terminals ...................................................................... 33 V dc
Differential input voltage ........................................................................................... ±15 V dc
Output short-circuit duration ..................................................................................... Indefinite 1/
Peak output current .................................................................................................. ±50 mA
Storage temperature range ....................................................................................... -65°C to +150°C
Maximum power dissipation (PD):
Case E .................................................................................................................. 1.33 W 2/
Case 2 ................................................................................................................... 1.32 W 3/
Lead temperature (soldering, 10 seconds) ............................................................... +275°C
Thermal resistance, junction-to-case (θJC) ................................................................ See MIL-STD-1835
Thermal resistance, junction-to-ambient (θJA):
Case E .................................................................................................................. 75°C/W
Case 2 ................................................................................................................... 76°C/W
Junction temperature (TJ) ......................................................................................... +175°C
1.4 Recommended operating conditions.
Positive supply voltage (+V) ..................................................................................... +15 V dc
Negative supply voltage (-V) ..................................................................................... -15 V dc
Logic supply voltage (+VL) ........................................................................................ +5.0 V dc
Logic reference voltage (-VL) .................................................................................... 0 V dc
Ambient temperature range (TA) ............................................................................... -55°C to +125°C
1/ One amplifier shorted to ground.
2/ Derate linearly above TA = +75°C at 13.4 mW/°C.
3/ Derate linearly above TA = +75°C at 13.1 mW/°C.
STANDARD
MICROCI RCUIT DRAWING
SIZE
A
5962-86860
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000 REVISION LEVEL
B SHEET 3
DSCC FORM 2234
APR 97
2. APPLICABLE DOCUMENTS
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a
part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed
in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in
the solicitation.
SPECIFICATION
DEPARTMENT OF DEFENSE
MIL-PRF-38535 -- Integrated Circuits, Manufacturing, General Specification for.
STANDARDS
DEPARTMENT OF DEFENSE
MIL-STD-883 - Test Method Standard Microcircuits.
MIL-STD-1835 - Interface Standard Electronic Component Case Outlines.
HANDBOOKS
DEPARTMENT OF DEFENSE
MIL-HDBK-103 -- List of Standard Microcircuit Drawings.
MIL-HDBK-780 - Standard Microcircuit Drawings.
(Unless otherwise indicated, copies of the specification, standards, and handbooks are available from the Standardization
Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text
of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
specific exemption has been obtained.
3. REQUIREMENTS
3.1 Item requirements. The individual item requirements shall be in accordance wi th MIL-PRF-38535, appendix A for non-
JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer
Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-
PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying
activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan
may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device.
These modifications shall not affect the PIN as described herein. A "Q" or "QML" certification mark in accordance with MIL-
PRF-38535 is required to identify when the QML flow option is used.
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as
specified in MIL-PRF-38535, appendix A and herein.
3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.2 herein.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1.
3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are
as specified in table I and shall apply over the full ambient operating temperature range.
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical
tests for each subgroup are described in table I.
3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN
listed in 1.2 herein. In addition, the manufacturer's PIN may also be marked as listed in MIL-HDBK-103 (see 6.6 herein). For
packages where marking of the entire SMD PIN number is not feasible due to space limitati ons, the manufacturer has the
option of not marking the "5962-" on the device.
STANDARD
MICROCI RCUIT DRAWING
SIZE
A
5962-86860
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000 REVISION LEVEL
B SHEET 4
DSCC FORM 2234
APR 97
TABLE I. Electrical performance characteristics.
Test
Symbol
Conditions 1/
-55°C ≤ TA ≤ +125°C
unless otherwise specified
Group A
subgroups
Device
type
Limits Unit
Min Max
1
±5.0
Input offset voltage
VIO V
CM = 0 V, VOUT = 1.4 V 2/ 2, 3 01 ±8.0 mV
1
±150
+IB 2, 3 ±200
1
±150
Input bias current
-IB
VCM = 0 V
2, 3
01
±200
nA
1
±35
Input offset current
IIO V
CM = 0 V 2, 3 01 ±45 nA
1
±0.5
Input sensitivity
INSEN V
CM = 0 V 2, 3 01 ±0.6 mV
Output low voltage VOL I
SINK = 3.0 mA 1, 2, 3 01 0.4 V
Output high voltage VOH I
SOURCE = 3.0 mA 1, 2, 3 01 3.5 V
Output sink current ISINK VOUT ≤ 0.4 V 1, 2, 3 01 3.0 mA
Output source current ISOURCE VOUT ≥ 0.4 V 1, 2, 3 01 -3.0 mA
+ICC 1, 2, 3 20
1 8.0
Supply current -ICC VOUT = VOL and VOH
2, 3
01
10
mA
1 6.0 Logic current IL V
OUT = VOL and VOH 2, 3 01 8.0
mA
tPD0 100 mV input step, 4/
10 mV overdrive,
TA = +25°C
9 200
Response time 3/
tPD1 -100 mV input step, 4/
-10 mV overdrive,
TA = +25°C
9
01
200
ns
+VCM -15 12.4 Common mode voltage
range 3/ -VCM TA = +25°C 1 01
-15 12.4 V
1/ +V = 15 V, -V = -15 V, and VL = 0 V unless otherwise specified herein.
2/ Offset voltage is measured when VOUT = 1.4 V. Sensitivity is measured on the transition edge at 0.4 V and 3.5 V.
Sensitivity is the change in differential input voltage required to change the output state. Sensitivity includes the effects of
offset voltage and voltage gain. See figure 2.
3/ If not tested, shall be guaranteed to the limits specified in table I.
4/ Duty cycle = 50%, f = 100 Hz, inverting input is driven, and all unused inverting inputs are tied to +5.0 V. See figure 3.
STANDARD
MICROCI RCUIT DRAWING
SIZE
A
5962-86860
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000 REVISION LEVEL
B SHEET 5
DSCC FORM 2234
APR 97
Device type 01
Case outlines E 2
Terminal number Terminal symbol
1 +VL NC
2 OUT 1 +VL
3 -IN OUT 1
4 +IN -IN 1
5 -V +IN 1
6 +IN 2 NC
7 -IN 2 -V
8 OUT 2 +IN 2
9 -VL -IN 2
10 OUT 3 OUT 2
11 -IN 3 NC
12 +IN 3 -VL
13 +V OUT 3
14 +IN 4 -IN 3
15 -IN 4 +IN 3
16 OUT 4 NC
17 ---- +V
18 ---- +IN 4
19 ---- -IN 4
20 ---- OUT 4
NC = No connection
FIGURE 1. Terminal connections.
STANDARD
MICROCI RCUIT DRAWING
SIZE
A
5962-86860
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000 REVISION LEVEL
B SHEET 6
DSCC FORM 2234
APR 97
FIGURE 2. Offset voltage and sensitivity waveforms.
STANDARD
MICROCI RCUIT DRAWING
SIZE
A
5962-86860
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000 REVISION LEVEL
B SHEET 7
DSCC FORM 2234
APR 97
NOTE: Response time testing is done after VIO testing to acquire device offset voltage.
Ten millivolts overdrive is then added (or subtracted depending on state) to this
Measured VIO value.
FIGURE 3. Response time waveforms.
STANDARD
MICROCI RCUIT DRAWING
SIZE
A
5962-86860
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000 REVISION LEVEL
B SHEET 8
DSCC FORM 2234
APR 97
3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance
to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a "Q" or "QML" certification mark in
accordance with MIL-PRF-38535 to identify when the QML flow option is used.
3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an
approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DSCC-VA prior to
listing as an approved source of supply shall affirm that the manufacturer's product meets the requirements of MIL-PRF-
38535, appendix A and the requirements herein.
3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided
with each lot of microcircuits delivered to this drawing.
3.8 Notification of change. Notification of change to DSCC-VA shall be required in accordance with MIL-PRF-38535,
appendix A.
3.9 Verification and review. DSCC, DSCC's agent, and the acquiring activity retain the option to review the manufacturer's
facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the
reviewer.
4. QUALITY ASSURANCE PROVISIONS
4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535,
appendix A.
4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices
prior to quality conformance inspection. The following additional criteria shall apply:
a. Burn-in test, method 1015 of MIL-STD-883.
(1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision
level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall
specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in
test method 1015 of MIL-STD-883.
(2) TA = +125°C, minimum.
b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter
tests prior to burn-in are optional at the discretion of the manufacturer.
STANDARD
MICROCI RCUIT DRAWING
SIZE
A
5962-86860
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000 REVISION LEVEL
B SHEET 9
DSCC FORM 2234
APR 97
TABLE II. Electrical test requirements.
MIL-STD-883 test requirements Subgroups
(in accordance with
MIL-STD-883, method 5005,
table I)
Interim electrical parameters
(method 5004) ----
Final electrical test parameters
(method 5004) 1*, 2, 3
Group A test requirements
(method 5005) 1, 2, 3, 9
Groups C and D end-point
electrical parameters
(method 5005)
1
* PDA applies to subgroup 1.
4.3 Quality conformance inspection. Quality conformance inspection shall be in accordance with method 5005 of MIL-STD-
883 including groups A, B, C, and D inspections. The following additional criteria shall apply.
4.3.1 Group A inspection.
a. Tests shall be as specified in table II herein.
b. Subgroups 4, 5, 6, 7, 8, 10, and 11 in table I, method 5005 of MIL-STD-883 shall be omitted.
4.3.2 Groups C and D inspections.
a. End-point electrical parameters shall be as specified in table II herein.
b. Steady-state life test conditions, method 1005 of MIL-STD-883.
(1) Test condition A, B, C, or D . The test circuit shall be maintained by the manufacturer under document revision
level control and shall be made available to the preparing or acquiring activity upon request. The test circuit
shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent
specified in test method 1005 of MIL-STD-883.
(2) TA = +125°C, minimum.
(3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883.
5. PACKAGING
5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38535, appendix A.
6. NOTES
6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications
(original equipment), design applications, and logistics purposes.
6.2 Replaceability. Mi crocircuits covered by this drawing will replace the same generic device covered by a contractor-
prepared specification or drawing.
6.3 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated with the users of record for
the individual documents. This coordination will be accomplished using DD Form 1692, Engineering Change Proposal.
STANDARD
MICROCI RCUIT DRAWING
SIZE
A
5962-86860
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000 REVISION LEVEL
B SHEET 10
DSCC FORM 2234
APR 97
6.4 Record of users. Military and industrial users shall inform Defense Supply Center Columbus when a system application
requires configuration control and the applicable SMD. DSCC will maintain a record of users and this list will be used for
coordination and distribution of changes to the drawings. Users of drawings covering microelectronics devices (FSC 5962)
should contact DSCC-VA, telephone (614) 692-0544.
6.5 Comments. Comments on this drawing should be directed to DSCC-VA, Columbus, Ohio 43216-5000, or telephone
(614) 692-0547.
6.6 Approved sources of supply. Approved sources of supply are listed in MIL-HDBK-103. The vendors listed in MIL-
HDBK-103 have agreed to this drawing and a certificate of compliance (see 3.6 herein) has been submitted to and accepted
by DSCC-VA.
STANDARD MICROCIRCUIT DRAWING BULLETIN
DATE: 04-01-27
Approved sources of supply for SMD 5962-86860 are listed below for immediate acquisition information only and
shall be added to MIL-HDBK-103 and QML-38535 during the next revision. MIL-HDBK-103 and QML-38535 will be
revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a
certificate of compliance has been submitted to and accepted by DSCC-VA. This bulletin is superseded by the next
dated revision of MIL-HDBK-103 and QML-38535.
Standard
microcircuit drawing
PIN 1/
Vendor
CAGE
number
Vendor
similar
PIN 2/
5962-8686001EA 34371 HA1-4902/883
5962-86860012A 34371 HA4-4902/883
1/ The lead finish shown for each PIN representing
a hermetic package is the most readily available
from the manufacturer listed for that part. If the
desired lead finish is not listed contact the vendor
to determine its availability.
2/ Caution. Do not use this number for item
acquisition. Items acquired to this number may not
satisfy the performance requirements of this drawing.
Vendor CAGE Vendor name
number and address
34371 Intersil Corporation
2401 Palm Bay Blvd
P.O. Box 883
Melbourne, FL 32902-0883
The information contained herein is disseminated for convenience only and the
Government assumes no liability whatsoever for any inaccuracies in the
information bulletin.
