Document Number: 42018 For technical questions, contact: spresale@vishay.com www.vishay.com
Revision: 13-Feb-07 25
Type 715P
Vishay Sprague
Polypropylene Film Capacitors
ORANGE DROP®, Low Loss
Polyproplyene plastic film is employed as the
dielectric in Type 715P ORANGE DROP®
capacitors. Type 715P capacitors are ideal for
applications where high AC current flow is found,
as in certain solid-state TV vertical circuits, r-f
generators and pulse-forming networks where
dielectric heating is often a problem.
The polyproplyene dielectric film is similar to polystyrene in
that it can handle high AC currents due to is low loss but with
the added advantage of an operating temperature to
+ 105 °C.
Capacitance change with temperature is less than 3 % over
the entire operating temperature range. The temperature
coefficient is negative and virtually linear at 180 PPM/°C over
the temperature range of + 25 °C to + 105 °C. This
characteristic means the Type 715P is suitable for matching
with positive TC resistors and inductors to maintain circuit
stability.
Type 715P ORANGE DROP® capacitors are conformally
coated with a flame retardant epoxy.
Performance characteristics, as well as curves showing
typical variation in electrical characteristics as a function of
temperature and frequency, are given.
PERFORMANCE CHARACTERISTICS
Operating Temperature: - 55 °C to + 85 °C, standard; up to
+ 105 °C when working voltage is reduced to 50 % of the
+ 85 °C rating.
Insulation Resistance: After a 2 minute charge at rated
voltage or 500 V, whichever is less.
At + 25 °C: 400 000 Megohm for C ≤ 0.5 µF
200 000 Megohm - Microfarads for C > 0.5 Microfarads
At + 85 °C: 20 000 Megohm for C ≤ 0.5 Microfarads
10 000 Megohm - Microfarads for C > 0.5 Microfarads
At + 105 °C: 2000 Megohm for C ≤ 0.5 µF
1000 Megohm - Microfarads for C > 0.5 Microfarads
Capacitance Tolerance and Dissipation Factor:
Capacitors shall be measured at a frequency of 1000 Hz at
+ 25 °C or else be referred to measurements made at that
frequency and temperature. The maximum dissipation factor
shall be 0.1 %.
Dielectric Withstanding Voltage:
Capacitors rated below 1000 volts shall withstand a DC
potential of 250 % of rated voltage applied between terminals
for not more than 5 seconds. Capacitance rated 1000 volts
and above shall withstand a DC potential of 200 % of rated
voltage applied between the terminals for not more than 5
seconds. The test voltage must be applied and discharged
through a resistor of 1 ohm per volt.
Humidity Test: Condition capacitors with no voltage applied
for 72 hours at 95 % relative humidity and + 75 °C. Remove
capacitors from humidity chamber, wipe surface dry of
moisture and dry in circulating air for 4 hours. Measure
insulation resistance after a two minute charge at + 25 °C
and rated voltage or 500 VDC, whichever is less. Minimum
product of insulation resistance and capacitance shall be
50 000 Megohm - microfarads after test but need not exceed
100 000 Megohm. Not more than one failure in 12 units
tested shall be permitted.
DC Life Test: Capacitors are capable of withstanding a 500
hour life test at + 85 °C at 150 % of rated working voltage.
After test, capacitance shall not have changed by more than
5 % of initial value, insulation resistance shall not have
decreased by more than 50 % of the initial limit and
dissipation factor shall not have increased to more than
0.1 %.
AC Life Test: Capacitors shall withstand the maximum
60 Hz voltage for a period of 500 hours at + 85 °C.
Not more than one failure allowed in 12 units tested.
RoHS
COMPLIANT
Rated DC Voltage Maximum 60 Hz Voltage
200 155
400, 600 200
800, 1200, 1600 500
www.vishay.com For technical questions, contact: spresale@vishay.com Document Number: 42018
26 Revision: 13-Feb-07
Type 715P
Vishay Sprague Polypropylene Film Capacitors
ORANGE DROP®, Low Loss
DIMENSIONS in inches (millimeters)
CASE
CODE
L
(Max.)
S
Terminal A
± 0.060 [1.524]
Terminal B
± 0.030 [ 0.762]
Terminal D
± 0.030 [0.762]
J 0.75 [19.050] 0.500 [12.700] 0.500 [12.700] 0.375 [9.525]
K 0.95 [24.130] 0.688 [17.475] 0.688 [17.475] 0.375 [9.525]
L 1.30 [33.020] 1.031 [26.187] 0.969 [24.613] 0.719 [18.263]
M 1.70 [43.180] 1.406 [35.712] 1.344 [34.138] 1.094 [27.788]
Terminal D
L
Max.
0.250
[6.350]
Max.
1.250
[31.750]
Min.
S
B lanimreTA lanimreT
S
L
Max.
0.250
[6.350]
Max.
Lead
Length
L
Max.
0.250
[6.350]
Max.
Lead
Length
S
D
Max.
0.032 [0.813] Dia.
(No. 20 AWG)
Tinned Copper-Clad Steel
PERFORMANCE CHARACTERISTICS
- 55 - 25 0 + 25 + 50 + 85 + 105 + 125
- 50 + 75 + 100
TEMPERATURE DEG. CENTIGRADE
+ 2
+ 1
0
- 1
- 2
- 55 - 25 0 + 25 + 50 + 85 + 105 + 125
- 50 + 75 + 100
TEMPERATURE DEG. CENTIGRADE
0.075
0.05
0.025
0
NOITAPI
SSID
TN
E
C
R
EP
1000 Hz
-
ROTCAF
ECNATICAPAC TNEC
REP
z H0001
-
EGNAHC
10
-2
5
2
10
-3
5
2
10
-4
NAT ?
?
?
?
?
1 2 5 10 2 5 100 2 5 1000
TEMPERATURE DEG. CENTIGRADE
TYPICAL
TYPICAL TYPICAL
1000
5
200
100
5
2
10
smr
-
S
T
LO
V
1 2 5 10 2 5 100 2 5 1000
FREQUENCY - kHz
s
mr
-
STLOV
FREQUENCY - kHz
1 2 5 10 2 5 100 2 5 1000
1000
5
2
155
100
5
2
10
.0039
µ
F
.018
µ
F
.039
µ
F
.18
µ
F
.47
µ
F
.012
µ
F
.039
µ
F
.27
µ
F
.47
µ
F
200 V 400 V
.082
µ
F
Type 715P
Polypropylene Film Capacitors
ORANGE DROP®, Low Loss Vishay Sprague
Document Number: 42018 For technical questions, contact: spresale@vishay.com www.vishay.com
Revision: 13-Feb-07 27
* Bolded items, when ordered as ± 5 % tolerance with D3 leads, are standard capacitors in stock and available through the Sprague® Distribution
Network. To complete the Type 715P Part Number, add the “D3” suffix and change the capacitance tolerance code number from a “9” to a “5” to
indicate ± 5 % (i.e., 715P10456LD3). Any other Part Number, value or type may easily be ordered as a Special.
** 60 Hz rms
PERFORMANCE CHARACTERISTICS
smr - STLOV
1 2 5 10 2 5 100 2 5 1000
FREQUENCY - kHz
0.001 µF
0.0082 µF
0.027 µF
0.12 µF
0.22 µF
600 V 800 V
s
mr - STLOV
1 2 5 10 2 5 100 2 5 1000
FREQUENCY - kHz
1000
450
200
100
5
2
10
0.0056 µF
0.018 µF
0.033 µF
0.056 µF
0.1 µF
1200 V
1000
5
200
100
5
2
10
1000
475
2
100
5
2
10
smr - STLOV
1 2 5 10 2 5 100 2 5 1000
FREQUENCY - kHz
0.0027 µF
0.015 µF
0.047 µF
1600 V
1000
500
2
100
5
2
10
smr - STLO
V
1 2 5 10 2 5 100 2 5 1000
FREQUENCY - kHz
0.0018 µF
0.0056 µF
0.01 µF
0.033 µF
0.018 µF
0.0082 µF
0.0039 µF
0.027 µF
STANDARD RATINGS* in inches (millimeters)
µF
± 10 % TOLERANCE PART NUMBER
SIZE
LD
200 VDC/155 VAC**
0.012 715P12392J 0.75 [19.05] 0.37 [9.40]
0.015 715P15392J 0.75 [19.05] 0.37 [9.40]
0.018 715P18392J 0.75 [19.05] 0.37 [9.40]
0.022 715P22392J 0.75 [19.05] 0.37 [9.40]
0.027 715P27392J 0.75 [19.05] 0.42 [10.67]
0.033 715P33392J 0.75 [19.05] 0.42 [10.67]
0.039 715P39392K 0.95 [24.13] 0.40 [10.16]
0.047 715P47392K 0.95 [24.13] 0.40 [10.16]
0.056 715P56392K 0.95 [24.13] 0.45 [11.43]
0.068715P68392K 0.95 [24.13] 0.45 [11.43]
0.082 715P82392L 1.30 [33.02] 0.45 [11.43]
0.1 715P10492L 1.30 [33.02] 0.45 [11.43]
0.12 715P12492L 1.30 [33.02] 0.55 [13.97]
0.15 715P15492L 1.30 [33.02] 0.55 [13.97]
0.18 715P18492L 1.30 [33.02] 0.62 [15.75]
0.22 715P22492L 1.30 [33.02] 0.62 [15.75]
0.27 715P27492M 1.70 [43.18] 0.65 [16.51]
0.33 715P33492M 1.70 [43.18] 0.65 [16.51]
0.39 715P39492M 1.70 [43.18] 0.75 [19.05]
0.47 715P47492M 1.70 [43.18] 0.75 [19.05]
www.vishay.com For technical questions, contact: spresale@vishay.com Document Number: 42018
28 Revision: 13-Feb-07
Type 715P
Vishay Sprague Polypropylene Film Capacitors
ORANGE DROP®, Low Loss
* Bolded items, when ordered as ± 5 % tolerance with D3 leads are standard capacitors in stock and available through the Sprague® Distribution
Network. To complete the Type 715P Part Number, add the “D3” suffix and change the capacitance tolerance code number from a “9” to a “5” to
indicate ± 5 % (i.e., 715P10456LD3). Any other Part Number, value or type may easily be ordered as a Special.
** 60 Hz rms
STANDARD RATINGS in inches (millimeters)
µF
± 10 % TOLERANCE PART NUMBER SIZE
LD
400 VDC/200 VAC**
0.0039 715P39294J 0.75 [19.05] 0.40 [10.16]
0.0047 715P47294J 0.75 [19.05] 0.40 [10.16]
0.0056 715P56294J 0.75 [19.05] 0.40 [10.16]
0.0068 715P68294J 0.75 [19.05] 0.40 [10.16]
0.0082 715P82294J 0.75 [19.05] 0.40 [10.16]
0.01 715P10394J 0.75 [19.05] 0.40 [10.16]
0.012 715P12394J 0.75 [19.05] 0.45 [11.43]
0.015 715P15394J 0.75 [19.05] 0.45 [11.43]
0.018 715P18394K 0.95 [24.13] 0.45 [11.43]
0.022 715P22394K 0.95 [24.13] 0.45 [11.43]
0.027 715P27394K 0.95 [24.13] 0.50 [12.70]
0.033 715P33394K 0.95 [24.13] 0.50 [12.70]
0.039 715P39394L 1.30 [33.02] 0.50 [12.70]
0.047 715P47394L 1.30 [33.02] 0.50 [12.70]
0.056 715P56394L 1.30 [33.02] 0.55 [13.97]
0.068 715P68394L 1.30 [33.02] 0.55 [13.97]
0.082 715P82394L 1.30 [33.02] 0.60 [15.24]
0.1 715P10494L 1.30 [33.02] 0.60 [15.24]
0.12 715P12494L 1.30 [33.02] 0.65 [16.51]
0.15 715P15494L 1.30 [33.02] 0.65 [16.51]
0.18 715P18494M 1.70 [43.18] 0.70 [17.78]
0.22 715P22494M 1.70 [43.18] 0.70 [17.78]
0.27 715P27494M 1.70 [43.18] 0.80 [20.32]
0.33 715P33494M 1.70 [43.18]0.80 [20.32]
0.39 715P39494M 1.70 [43.18] 0.90 [22.86]
0.47 715P47494M 1.70 [43.18] 0.90 [22.86]
600 VDC/200 VAC**
0.001 715P10296J 0.75 [19.05] 0.40 [10.16]
0.0012 715P12296J 0.75 [19.05] 0.40 [10.16]
0.0015 715P15296J 0.75 [19.05] 0.40 [10.16]
0.0018 715P18296J 0.75 [19.05] 0.40 [10.16]
0.0022 715P22296J 0.75 [19.05] 0.40 [10.16]
0.0027 715P27296J 0.75 [19.05] 0.40 [10.16]
0.0033 715P33296J 0.75 [19.05] 0.40 [10.16]
0.0039 715P39296J 0.75 [19.05] 0.45 [11.43]
0.0047 715P47296J 0.75 [19.05] 0.45 [11.43]
0.0056 715P56296J 0.75 [19.05] 0.45 [11.43]
0.0068 715P68296J 0.75 [19.05] 0.45 [11.43]
0.0082 715P82296K 0.95 [24.13] 0.45 [11.43]
0.01 715P10396K 0.95 [24.13] 0.45 [11.43]
0.012 715P12396K 0.95 [24.13] 0.50 [12.70]
0.015 715P15396K 0.95 [24.13] 0.50 [12.70]
0.018 715P18396K 0.95 [24.13] 0.55 [13.97]
0.022 715P22396K 0.95 [24.13] 0.55 [13.97]
0.027 715P27396L 1.30 [33.02] 0.55 [13.97]
0.033 715P33396L 1.30 [33.02] 0.55 [13.97]
0.039 715P39396L 1.30 [33.02] 0.60 [15.24]
0.047 715P47396L 1.30 [33.02] 0.60 [15.24]
0.056 715P56396L 1.30 [33.02] 0.65 [16.51]
0.068715P68396L 1.30 [33.02] 0.65 [16.51]
0.082 715P82396L 1.30 [33.02] 0.75 [19.05]
0.1 715P10496L 1.30 [33.02] 0.75 [19.05]
0.12 715P12496M 1.70 [43.18] 0.75 [19.05]
0.15 715P15496M 1.70 [43.18] 0.75 [19.05]
0.18 715P18496M 1.70 [43.18] 0.85 [21.59]
0.22 715P22496M 1.70 [43.18]0.85 [21.59]
Type 715P
Polypropylene Film Capacitors
ORANGE DROP®, Low Loss Vishay Sprague
Document Number: 42018 For technical questions, contact: spresale@vishay.com www.vishay.com
Revision: 13-Feb-07 29
* Bolded items, when ordered as ± 5 % tolerance with D3 leads are standard capacitors in stock and available through the Sprague® Distribution
Network. To complete the Type 715P Part Number, add the “D3” suffix and change the capacitance tolerance code number from a “9” to a “5” to
indicate ± 5 % (i.e., 715P10456LD3). Any other Part Number, value or type may easily be ordered as a Special.
** 60 Hz rms
STANDARD RATINGS in inches (millimeters)
µF
± 10 % TOLERANCE PART NUMBER SIZE
LD
800 VDC/450 VAC**
0.0056 715P56298L 1.30 [33.02] 0.50 [12.70]
0.0068 715P68298L 1.30 [33.02] 0.50 [12.70]
0.0082 715P82298L 1.30 [33.02] 0.50 [12.70]
0.01 715P10398L 1.30 [33.02] 0.50 [12.70]
0.012 715P12398L 1.30 [33.02] 0.55 [13.97]
0.015 715P15398L 1.30 [33.02] 0.55 [13.97]
0.018 715P18398L 1.30 [33.02] 0.60 [15.24]
0.022 715P22398L 1.30 [33.02] 0.60 [15.24]
0.027 715P27398L 1.30 [33.02] 0.70 [17.78]
0.033 715P33398L 1.30 [33.02] 0.70 [17.78]
0.039 715P39398M 1.70 [43.18] 0.70 [17.78]
0.047 715P47398M 1.70 [43.18] 0.70 [17.78]
0.056 715P56398M 1.70 [43.18] 0.80 [20.32]
0.068715P68398M 1.70 [43.18]0.80 [20.32]
0.082 715P82398M 1.70 [43.18] 0.90 [22.86]
0.1 715P10498M 1.70 [43.18] 0.90 [22.86]
1200 VDC/475 VAC**
0.0027 715P272912L 1.30 [33.02] 0.50 [12.70]
0.0033 715P332912L 1.30 [33.02] 0.50 [12.70]
0.0039 715P392912L 1.30 [33.02] 0.50 [12.70]
0.0047 715P472912L 1.30 [33.02] 0.50 [12.70]
0.0056 715P562912L 1.30 [33.02] 0.55 [13.97]
0.0068 715P682912L 1.30 [33.02] 0.55 [13.97]
0.0082 715P822912L 1.30 [33.02] 0.60 [15.24]
0.01 715P103912L 1.30 [33.02] 0.60 [15.24]
0.012 715P123912L 1.30 [33.02] 0.65 [16.51]
0.015 715P153912L 1.30 [33.02] 0.65 [16.51]
0.018 715P183912M 1.70 [43.18] 0.65 [16.51]
0.022 715P223912M 1.70 [43.18] 0.65 [16.51]
0.027 715P273912M 1.70 [43.18] 0.75 [19.05]
0.033 715P333912M 1.70 [43.18] 0.75 [19.05]
0.039 715P393912M 1.70 [43.18] 0.85 [21.59]
0.047 715P473912M 1.70 [43.18]0.85 [21.59]
1600 VDC/500 VAC**
0.0018 715P182916L 1.30 [33.02] 0.50 [12.70]
0.0022 715P222916L 1.30 [33.02] 0.50 [12.70]
0.0027 715P272916L 1.30 [33.02] 0.55 [13.97]
0.0033 715P332916L 1.30 [33.02] 0.55 [13.97]
0.0039 715P392916L 1.30 [33.02] 0.60 [15.24]
0.0047 715P472916L 1.30 [33.02] 0.60 [15.24]
0.0056 715P562916L 1.30 [33.02] 0.65 [16.51]
0.0068715P682916L 1.30 [33.02] 0.65 [16.51]
0.0082 715P822916L 1.30 [33.02] 0.70 [17.78]
0.01 715P103916L 1.30 [33.02] 0.70 [17.78]
0.012 715P123916M 1.70 [43.18] 0.75 [19.05]
0.015 715P153916M 1.70 [43.18] 0.75 [19.05]
0.018 715P183916M 1.70 [43.18] 0.85 [21.59]
0.022 715P223916M 1.70 [43.18]0.85 [21.59]
0.027 715P273916M 1.70 [43.18] 0.95 [24.13]
0.033 715P333916M 1.70 [43.18] 0.95 [24.13]
www.vishay.com For technical questions, contact: spresale@vishay.com Document Number: 42018
30 Revision: 13-Feb-07
Type 715P
Vishay Sprague Polypropylene Film Capacitors
ORANGE DROP®, Low Loss
STANDARD MARKING FORMAT
SAMPLE MARKING DESCRIPTION
TOLERANCE CODES
PER EIA STANDARDS
d715P200 V
1239 9340
d Sprague® Indentification
715P Type Number
200 V DC Voltage Rating, Volts
1239 Capacitance and Tolerance Code
9940 Weekly Date Code (i.e. 40th week for 1999)
9 = ± 10 %
5 = ± 5 %
2 = ± 2 %
ORDERING INFORMATION
715P 123 9 2 J D 3
TYPE CAPACITANCE TOLERANCE DC VOLTAGE
RATING AT + 85
°C
CASE
CODE
TERMINAL LEAD LENGTH
Capacitance is expressed in
picofarads. The first two digits
are significant. The third is the
number of zeros to follow.
Values must conform to
Decade Rating for the
tolerance specified.
9 = ± 10 %
5 = ± 5 %
2 = ± 2 %
This is expressed
in hundreds of
volts.
Example: 715P
R5 = 50 volts
See
Dimensional
Configurations.
A = Straight Lead
B = Hairpin Crimped
D = Hockey Crimped
1 = 0.187"± 0.030"
[4.750 ± 0.762]
2 = 0.250" ± 0.030"
[ 6.350 ± 0.762]
3 = 1.250" [31.750]
Minimum
Legal Disclaimer Notice
www.vishay.com Vishay
Revision: 12-Mar-12 1Document Number: 91000
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree
to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and
damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay
or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to
obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
