MP2161 2A, 6V, 1.5MHz, 17A IQ, COT Synchronous Step Down Switcher In 8-pin TSOT23 The Future of Analog IC Technology DESCRIPTION FEATURES The MP2161 is a monolithic step-down switch mode converter with built-in internal power MOSFETs. It achieves 2A continuous output current from a 2.5V to 6V input voltage with excellent load and line regulation. The output voltage can be regulated as low as 0.6V. * * * * The Constant-On-Time control scheme provides fast transient response and eases loop stabilization. Fault condition protection includes cycle-by-cycle current limiting and thermal shutdown. The MP2161 is available in the small TSOT23-8 package and requires a minimum number of readily available standard external components. The MP2161 is ideal for a wide range of applications including High Performance DSPs, FPGAs, PDAs, and portable instruments. * * * * * * * Very Low IQ: 17A Default 1.5MHz Switching Frequency EN and Power Good for Power Sequencing Wide 2.5V to 6V Operating Input Range Output Adjustable from 0.6V Up to 2A Output Current 100% Duty Cycle in Dropout 100m and 60m Internal Power MOSFET Switches Cycle-by-Cycle Over Current Protection Short Circuit Protect with Hiccup Mode Stable with Low ESR Output Ceramic Capacitors Available in a TSOT23-8 Package APPLICATIONS * * * * Wireless/Networking Cards Portable Instruments Battery Powered Devices Low Voltage I/O System Power All MPS parts are lead-free and adhere to the RoHS directive. For MPS green status, please visit MPS website under Products, Quality Assurance page. "MPS" and "The Future of Analog IC Technology" are registered trademarks of Monolithic Power Systems, Inc. TYPICAL APPLICATION MP2161 Rev. 1.03 9/6/2013 www.MonolihicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. (c) 2013 MPS. All Rights Reserved. 1 MP2161 - 2A, 6V, 1.5MHz SYNCHRONOUS STEP-DOWN SWITCHER ORDERING INFORMATION Part Number* MP2161GJ Package TSOT23-8 Top Marking AEB * For Tape & Reel, add suffix -Z (e.g. MP2161GJ-Z); PACKAGE REFERENCE TOP VIEW PG 1 8 EN VIN 2 7 FB SW 3 6 AGND PGND 4 5 OUT TSOT23-8 ABSOLUTE MAXIMUM RATINGS (1) Thermal Resistance Supply Voltage VIN ...................................... 6.5V VSW ...................................................................... -0.3V (-1.5V for <10ns) to 6.5V (7V for <10ns) All Other Pins ................................-0.3V to 6.5 V Junction Temperature ...............................150C Lead Temperature ....................................260C (2) Continuous Power Dissipation (TA = +25C) ............... ............................................... 1.25W Storage Temperature............... -65C to +150C TSOT23-8.............................. 100 ..... 55... C/W Recommended Operating Conditions (3) Supply Voltage VIN .............................2.5V to 6V Operating Junction Temp. (TJ). -40C to +125C MP2161 Rev. 1.03 9/6/2013 (4) JA JC Notes: 1) Exceeding these ratings may damage the device. 2) The maximum allowable power dissipation is a function of the maximum junction temperature TJ (MAX), the junction-toambient thermal resistance JA, and the ambient temperature TA. The maximum allowable continuous power dissipation at any ambient temperature is calculated by PD (MAX) = (TJ (MAX)-TA)/JA. Exceeding the maximum allowable power dissipation will cause excessive die temperature, and the regulator will go into thermal shutdown. Internal thermal shutdown circuitry protects the device from permanent damage. 3) The device is not guaranteed to function outside of its operating conditions. 4) Measured on JESD51-7, 4-layer PCB. www.MonolihicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. (c) 2013 MPS. All Rights Reserved. 2 MP2161 - 2A, 6V, 1.5MHz SYNCHRONOUS STEP-DOWN SWITCHER ELECTRICAL CHARACTERISTICS (5) VIN = 5V, TA = +25C, unless otherwise noted. Parameter Symbol Feedback Voltage VFB Feedback Current PFET Switch On Resistance NFET Switch On Resistance IFB Condition 2.5V VIN 6V o o TA=-40 C to +85 C (6) Min Typ Max -3% 0.600 +3% -3.5% VFB = 0.6V RDSON_P RDSON_N VEN = 0V, VIN = 6V VSW = 0V and 6V Switch Leakage PFET Current Limit 2.7 ON Time TON Switching frequency Minimum Off Time Soft-Start Time Fs -20% -25% TMIN-OFF TSS-ON Power Good Upper Trip Threshold PGH Power Good Lower Trip Threshold Power Good Delay Power Good Sink Current Capability Power Good Logic High Voltage Power Good Internal Pull Up Resistor Under Voltage Lockout Threshold Rising Under Voltage Lockout Threshold Hysteresis EN Input Logic Low Voltage EN Input Logic High Voltage PGL PGD EN Input Current Supply Current (Shutdown) Supply Current (Quiescent) Thermal Shutdown(5) Thermal Hysteresis VIN=5V, VOUT=1.2V VIN=3.6V, VOUT=1.2V VOUT=1.2V TA=-40oC to +85oC(6) (5) FB voltage respect to the regulation VPG-L Sink 1mA VPG-H VIN=5V, VFB=0.6V +3.5% 50 nA m m 0 1 A 3.2 185 245 1500 1500 60 1.5 4.0 A ns +20% +25% % -10 50 % s V V 550 2.3 k 2.45 260 1.2 1.5 0 20 17 V mV 0.4 VEN=2V VEN=0V VEN=0V, VIN=3V VEN=2V, VFB=0.63V, VIN=5V kHz/% kHz/% ns ms +10 4.9 2.15 V/% 10 100 60 0.4 RPG Units 100 20 V V A A nA A 150 C 30 C Notes: 5) Guaranteed by design. 6) Guaranteed by characterization test. MP2161 Rev. 1.03 9/6/2013 www.MonolihicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. (c) 2013 MPS. All Rights Reserved. 3 MP2161 - 2A, 6V, 1.5MHz SYNCHRONOUS STEP-DOWN SWITCHER TYPICAL PERFORMANCE CHARACTERISTICS VIN = 5V, VOUT = 1.2V, L = 1.0H, TA = +25C, unless otherwise noted. Quiescent Current vs. Input Voltage Shutdown Current vs. Input Voltage 40 Load Regulation 2.00 0.003 1.50 0.0025 VIN=5V 1.00 30 20 0.002 0.50 0.0015 0.00 -0.50 0.001 VIN=6V -1.00 10 0.0005 -1.50 0 0 2 2.5 3 3.5 4 4.5 5 -2.00 2 5.5 6 2.5 3 3.5 4 4.5 5 5.5 6 0 INPUT VOLTAGE (V) INPUT VOLTAGE (V) Line Regulation 50 45 40 40 35 35 0.20 30 30 0.00 25 25 -0.20 20 20 15 15 -0.60 10 10 -0.80 5 0 5 0 0.40 Load=1A -0.40 -1.00 Load=2A Load=0A 2 3 4 5 0 6 1 1.5 2 0 2.5 100 2.5 0.5 1 1.5 2 2.5 OUTPUT CURRENT (A) Efficiency Efficiency 100 95 90 0.5 OUTPUT CURRENT (A) INPUT VOLTAGE (V) 2 VIN=5V, VOUT=3.3V 50 45 0.60 1.5 Case Temp Rise Case Temp Rise 0.80 1 LOAD CURRENT (A) VIN=3V, VOUT=1.2V 1.00 0.5 Efficiency 5/3.3VIN to 1.8VOUT 5VIN to 3.3VOUT 100 VIN=3.3V 90 90 85 80 80 75 VIN=6V VIN=5V 70 VIN=5V 80 VIN=3.3V 70 70 60 60 65 60 55 50 1 10 100 1000 10000 LOAD CURRENT(mA) MP2161 Rev. 1.03 9/6/2013 50 0 0.5 1 1.5 IOUT (A) 2 2.5 50 0 0.5 1 1.5 IOUT (A) www.MonolihicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. (c) 2013 MPS. All Rights Reserved. 2 2.5 4 MP2161 - 2A, 6V, 1.5MHz SYNCHRONOUS STEP-DOWN SWITCHER TYPICAL PERFORMANCE CHARACTERISTICS (continued) VIN = 5V, VOUT = 1.2V, L = 1.0H, TA = +25C, unless otherwise noted. MP2161 Rev. 1.03 9/6/2013 www.MonolihicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. (c) 2013 MPS. All Rights Reserved. 5 MP2161 - 2A, 6V, 1.5MHz SYNCHRONOUS STEP-DOWN SWITCHER TYPICAL PERFORMANCE CHARACTERISTICS (continued) VIN = 5V, VOUT = 1.2V, L = 1.0H, TA = +25C, unless otherwise noted MP2161 Rev. 1.03 9/6/2013 www.MonolihicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. (c) 2013 MPS. All Rights Reserved. 6 MP2161 - 2A, 6V, 1.5MHz SYNCHRONOUS STEP-DOWN SWITCHER PIN FUNCTIONS Pin # 1 2 3 4 5 6 7 8 MP2161 Rev. 1.03 9/6/2013 Name Description Power Good Indicator. The output of this pin is an open drain with internal pull up resistor PG to IN. PGOOD is pulled up to IN when the FB voltage is within 10% of the regulation level, if FB voltage is out of that regulation range, it is LOW. Supply Voltage. The MP2161 operates from a +2.5V to +6V unregulated input. C1 is VIN needed to prevent large voltage spikes from appearing at the input. SW Switch Output PGND Power ground OUT Input sense pin for output voltage AGND Analogy ground for internal control circuit Feedback pin. An external resistor divider from the output to GND, tapped to the FB pin, FB sets the output voltage. EN On/Off Control www.MonolihicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. (c) 2013 MPS. All Rights Reserved. 7 MP2161 - 2A, 6V, 1.5MHz SYNCHRONOUS STEP-DOWN SWITCHER BLOCK DIAGRAM VIN Bias & Voltage Reference EN Soft start + COMP VTH Lo-Iq 0.6V RST + + E.A. - Constant On- Time Pulse PDRV PWM Main Switch (PCH) PWM + Lo-Iq + FB SW EN FBCOMP Driver VOUT Lo-Iq Ramp generator Synchronous Rectifier ( NCH) SW Lo-Iq Hi-Z NDRV OUT GND IN FB for fixed output 0.66V + + COMP COMP - Lo-Iq + COMP 0.54V PG - Figure 1: MP2161 Block Diagram MP2161 Rev. 1.03 9/6/2013 www.MonolihicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. (c) 2013 MPS. All Rights Reserved. 8 MP2161 - 2A, 6V, 1.5MHz SYNCHRONOUS STEP-DOWN SWITCHER OPERATION MP2161 uses constant on-time control with input voltage feed forward to stabilize the switching frequency over full input range. At light load, MP2161 employs a proprietary control of low side switch and inductor current to eliminate ringing on switching node and improve efficiency. Constant On-time Control Compare to fixed frequency PWM control, constant on-time control offers the advantage of simpler control loop and faster transient response. By using input voltage feed forward, MP2161 maintains a nearly constant switching frequency across input and output voltage range. The ontime of the switching pulse can be estimated as: TON = VOUT 0.667s VIN To prevent inductor current run away during load transient, MP2161 fixes the minimum off time to be 60ns. However, this minimum off time limit will not affect operation of MP2161 in steady state in any way. Light Load Operation In light load condition, MP2161 uses a proprietary control scheme to save power and improve efficiency. The MP2161 will turn off the low side switch when inductor current starts to reverse. Then MP2161 works in discontinuous conduction mode (DCM) operation. Enable When input voltage is greater than the undervoltage lockout threshold (UVLO), typically 2.3V, MP2161 can be enabled by pulling EN pin to higher than 1.2V. Leaving EN pin float or pull down to ground will disable MP2161. There is MP2161 Rev. 1.03 9/6/2013 an internal 1Meg Ohm resistor from EN pin to ground. Soft Start MP2161 has built-in soft start that ramps up the output voltage in a controlled slew rate, avoiding overshoot at startup. The soft start time is about 1.5ms typical. Power GOOD Indictor MP2161 has an open drain with 550k pull-up resistor pin for power good indicator PGOOD. When FB pin is within +/-10% of regulation voltage, i.e. 0.6V, PGOOD pin is pulled up to IN by the internal resistor. If FB pin voltage is out of the +/-10% window, PGOOD pin is pulled down to ground by an internal MOS FET. The MOS FET has a maximum Rdson of less than 100 Ohm. Current limit MP2161 has a typical 3.2A current limit for the high side switch. When the high side switch hits current limit, MP2161 will touch the hiccup threshold until the current lower down. This will prevent inductor current from continuing to build up which will result in damage of the components. Short Circuit and Recovery MP2161 enters short circuit protection mode also when the current limit is hit, and tries to recover from short circuit with hiccup mode. In short circuit protection, MP2161 will disable output power stage, discharge soft-start cap and then automatically try to soft-start again. If the short circuit condition still holds after softstart ends, MP2161 repeats this operation cycle till short circuit disappears and output rises back to regulation level. www.MonolihicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. (c) 2013 MPS. All Rights Reserved. 9 MP2161 - 2A, 6V, 1.5MHz SYNCHRONOUS STEP-DOWN SWITCHER APPLICATION INFORMATION COMPONENT SELECTION Setting the Output Voltage The external resistor divider is used to set the output voltage (see Typical Application on page 1). The feedback resistor R1 can not be too large neither too small considering the trade-off for stability and dynamic. Choose R1 to be around 120k to 200k. R2 is then given by: R2 = R1 Vout -1 0.6 The feedback circuit is shown as Figure 2. Vout MP2161 R1 FB Figure 2: Feedback Network Table 1 lists the recommended resistors value for common output voltages. Table 1--Resistor Selection for Common Output Voltages R1 (k) 200(1%) 200(1%) 200(1%) 200(1%) 200(1%) R2 (k) 300(1%) 200(1%) 100(1%) 63.2(1%) 44.2(1%) Selecting the Inductor A 0.68H to 2.2H inductor is recommended for most applications. For highest efficiency, the inductor DC resistance should be less than 15m. For most designs, the inductance value can be derived from the following equation. L1 = VOUT x (VIN - VOUT ) VIN x IL x fOSC Where IL is the inductor ripple current. MP2161 Rev. 1.03 9/6/2013 IL(MAX) = ILOAD + I L 2 Selecting the Input Capacitor The input current to the step-down converter is discontinuous, therefore a capacitor is required to supply the AC current to the step-down converter while maintaining the DC input voltage. Use low ESR capacitors for the best performance. Ceramic capacitors with X5R or X7R dielectrics are highly recommended because of their low ESR and small temperature coefficients. For most applications, a 10F capacitor is sufficient. For higher output voltage, 47uF may be needed for more stable system. Since the input capacitor absorbs the input switching current it requires an adequate ripple current rating. The RMS current in the input capacitor can be estimated by: R2 VOUT (V) 1.0 1.2 1.8 2.5 3.3 Choose inductor current to be approximately 30% of the maximum load current. The maximum inductor peak current is: I C1 = ILOAD x VOUT VOUT x 1- VIN VIN The worse case condition occurs at VIN = 2VOUT, where: IC1 = ILOAD 2 For simplification, choose the input capacitor whose RMS current rating greater than half of the maximum load current. The input capacitor can be electrolytic, tantalum or ceramic. When using electrolytic or tantalum capacitors, a small and high quality ceramic capacitor, i.e. 0.1F, should be placed as close to the IC as possible. When using ceramic capacitors, make sure that they have enough capacitance to provide sufficient charge to prevent excessive voltage ripple at input. The input voltage ripple caused by capacitance can be estimated by: VIN = ILOAD V V x OUT x 1 - OUT fS x C1 VIN VIN www.MonolihicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. (c) 2013 MPS. All Rights Reserved. 10 MP2161 - 2A, 6V, 1.5MHz SYNCHRONOUS STEP-DOWN SWITCHER Selecting the Output Capacitor The output capacitor (C2) is required to maintain the DC output voltage. Ceramic capacitors are recommended. Low ESR capacitors are preferred to keep the output voltage ripple low. The output voltage ripple can be estimated by: VOUT = VOUT VOUT 1 x 1 - x RESR + fS x L1 VIN 8 x fS x C2 Where L1 is the inductor value and RESR is the equivalent series resistance (ESR) value of the output capacitor. Using ceramic capacitors, the impedance at the switching frequency is dominated by the capacitance. The output voltage ripple is mainly caused by the capacitance. For simplification, the output voltage ripple can be estimated by: Proper layout of the switching power supplies is very important, and sometimes critical for proper function. For the high-frequency switching converter, poor layout design can result in poor line or load regulation and stability issues. The high current paths (GND, IN and SW) should be placed very close to the device with short, direct and wide traces. The input capacitor needs to be as close as possible to the IN and GND pins. The external feedback resistors should be placed next to the FB pin. Keep the switching node SW short and away from the feedback network. PG AGND V VOUT x 1 - OUT 2 VIN 8 x fS x L1 x C2 C1 In the case of tantalum or electrolytic capacitors, the ESR dominates the impedance at the switching frequency. For simplification, the output ripple can be approximated to: VOUT = VOUT V x 1 - OUT x RESR fS x L1 VIN The characteristics of the output capacitor also affect the stability of the regulation system. EN 1 2 3 4 8 7 6 5 R2 R1 VOUT = PCB Layout C2 SW VIN GND OUT Figure 3: PCB Layout Recommendation Design Example Below is a design example following the application guidelines for the specifications: Table 2: Design Example 5V VIN 1.2V VOUT 1500kHz fSW The detailed application schematic is shown in Figure 4. The typical performance and circuit waveforms have been shown in the Typical Performance Characteristics section. For more device applications, please refer to the related Evaluation Board Datasheets. MP2161 Rev. 1.03 9/6/2013 www.MonolihicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. (c) 2013 MPS. All Rights Reserved. 11 MP2161 - 2A, 6V, 1.5MHz SYNCHRONOUS STEP-DOWN SWITCHER TYPICAL APPLICATION CIRCUITS Figure 4: Typical Application Circuit MP2161 Rev. 1.03 9/6/2013 www.MonolihicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. (c) 2013 MPS. All Rights Reserved. 12 MP2161 - 2A, 6V, 1.5MHz SYNCHRONOUS STEP-DOWN SWITCHER PACKAGE INFORMATION TSOT23-8 See note 7 EXAMPLE TOP MARK PIN 1 ID IAAAA RECOMMENDED LAND PATTERN TOP VIEW SEATING PLANE SEE DETAIL''A'' FRONT VIEW SIDE VIEW NOTE: DETAIL ''A'' 1) ALL DIMENSIONS ARE IN MILLIMETERS . 2) PACKAGE LENGTH DOES NOT INCLUDE MOLD FLASH , PROTRUSION OR GATE BURR. 3) PACKAGE WIDTH DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. 4) LEAD COPLANARITY(BOTTOM OF LEADS AFTER FORMING) SHALL BE 0.10 MILLIMETERS MAX. 5) JEDEC REFERENCE IS MO-193, VARIATION BA. 6) DRAWING IS NOT TO SCALE. 7) PIN 1 IS LOWER LEFT PIN WHEN READING TOP MARK FROM LEFT TO RIGHT, (SEE EXAMPLE TOP MARK) NOTICE: The information in this document is subject to change without notice. Please contact MPS for current specifications. Users should warrant and guarantee that third party Intellectual Property rights are not infringed upon when integrating MPS products into any application. MPS will not assume any legal responsibility for any said applications. MP2161 Rev. 1.03 9/6/2013 www.MonolithicPower.com MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. (c) 2013 MPS. All Rights Reserved. 13 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Monolithic Power Systems (MPS): MP2161GJ-P MP2161GJ-Z