DL4728A
THRU
DL4761A
1 Watt
Zener Diode
3.3 to 75 Volts
Features
xHigh Reliability
xVery Sharp Reverse Characteristic
xLow Reverse Current Level
Maximum Ratings
xOperating Temperature: -65 к to +175 кxStorage Temperature: -65 к to +175 кx1 Watt DC Power Dissipation
xMaximum Thermal Resistance: 100K/W Junction To Ambient
Test Conditions: I = 9.5mm(3/8”),TL= constant
xMaximum Forward Voltage @ 200mA: 1.2 Volts
Figure 2 - Derating Curve
Power Dissipation (W) - Versus - Temperature кTemperature к25 100 150 200
W
0.5
1.0
Typical Temperature Coefficient (mV/ к) – versus – Zener Voltage (VZ)
Figure 1 - Typical Temperature Coefficient
020 40
0
20
40
mV/ кVZ
omponents
20736 Marilla Street Chatsworth
!"#
$% !"#
MCC
GLASS MELF
SUGGESTED SOLDER
PAD LAYOUT
INCHES MM
DIM MIN MAX MIN MAX NOTE
A .190 .205 4.80 5.20
B --- .022 --- .55 Nominal
C .095 .105 2.40 2.67 ∅
A
B
C
Cathode Mark
.210”
.035”
.115”
Revision: C 2012/08/23
TM
Micro Commercial Components
www.mccsemi.com
1 of 3
• Lead Free Finish/RoHS Compliant(Note 1) ("P" Suffix designates
RoHS Compliant. See ordering information)
Notes: 1. Lead in Glass Exemption Applied, see EU Directive Annex Notes 7(C)-I.
• Moisture Sensitivity Level 1
ELECTRICAL CHARACTERISTICS @25°C
MCC
PART
NUMBER
ZENER
VOLTAGE
VZ
TEST
CURRENT
IZT
MAXIMUM
DYNAMIC
IMPEDANCE
ZZT @ IZT
MAXIMUM
REVERSE
CURRENT
IR @ VR
TEST
VOLTAGE
VR
MAXIMUM
REGULATOR
CURRENT
IZM
TA = 50°C
MAXIMUM
KNEE
IMPEDANCE
ZZK @ IZK
TEST
CURRENT
IZK
MAXIMUM
SURGE
CURRENT
IS
VOLTS m A OHMS µA VOLTS mA OHMS mA mA
DL4728A 3 . 3 76 10 100 1 276 400 1 . 0 1280
DL4729A 3 . 6 69 10 100 1 252 400 1 . 0 1260
DL4730A 3 . 9 64 9 50 1 234 400 1 . 0 1190
DL4731A 4. 3 58 9 10 1 217 400 1 . 0 1070
DL4732A 4 . 7 53 8 10 1 193 500 1 . 0 970
DL4733A 5 . 1 49 7 10 1 178 550 1 . 0 890
DL4734A 5 . 6 45 5 10 2 162 600 1 . 0 810
DL4735A 6 . 2 41 2 10 3 146 700 1 . 0 730
DL4736A 6 . 8 37 3 . 5 10 4 133 700 1 . 0 660
DL4737A 7 . 5 34 4 . 0 10 5 121 700 0 . 5 605
DL4738A 8 . 2 31 4 . 5 10 6 110 700 0 . 5 550
DL4739A 9 . 1 28 5 . 0 10 7 100 700 0 . 5 500
DL4740A 10 25 7 10 7 . 6 91 700 0.25 454
DL4741A 11 23 8 5 8 . 4 83 700 0.25 414
DL4742A 12 21 9 5 9 . 1 76 700 0.25 380
DL4743A 13 19 10 5 9 . 9 69 700 0.25 344
DL4744A 15 17 14 5 1 1 . 4 61 700 0.25 304
DL4745A 16 1 5 . 5 16 5 1 2 . 2 57 700 0.25 285
DL4746A 18 14 20 5 1 3 . 7 50 750 0.25 250
DL4747A 20 1 2 . 5 22 5 1 5 . 2 45 750 0.25 225
DL4748A 22 1 1 . 5 23 5 1 6 . 7 41 750 0.25 205
DL4749A 24 1 0 . 5 25 5 1 8 . 2 38 750 0.25 190
DL4750A 27 9 . 5 35 5 2 0 . 6 34 750 0.25 170
DL4751A 30 8 . 5 40 5 2 2 . 8 30 1000 0.25 150
DL4752A 33 7 . 5 45 5 2 5 . 1 27 1000 0.25 135
DL4753A 36 7 . 0 50 5 2 7 . 4 25 1000 0.25 125
DL4754A 39 6 . 5 60 5 2 9 . 7 23 1000 0.25 115
DL4755A 43 6 . 0 70 5 3 2 . 7 22 1500 0.25 110
DL4756A 47 5 . 5 80 5 3 5 . 8 19 1500 0.25 95
DL4757A 51 5 . 0 95 5 3 8 . 8 18 1500 0.25 90
DL4758A 56 4 . 5 110 5 4 2 . 6 16 2000 0.25 80
DL4759A 62 4 . 0 125 5 4 7 . 1 14 2000 0.25 70
DL4760A 68 3 . 7 150 5 5 1 . 7 13 2000 0.25 65
DL4761A 75 3 . 3 175 5 5 6 . 0 12 2000 0.25 60
NOTE 1 The JEDEC type numbers shown have A 5% tolerance on nominal zener voltage.
Suffix A signifies 5% tolerance, C signifies 2% tolerance.
NOTE 2 The zener impedance is derived from the 60Hz AC voltage, which results when an AC current having an rms value equal to
10% of the DC zener current (Izt or Izk) is superimposed on Izt or Izk. Zener impedance is measured at two points to insure
a sharp knee on the breakdown curve and eliminate unstable units.
NOTE 3 The reverse surge current is measured at 25oC ambient using a 1/2 square wave or equivalent sine wave pulse 1/120 second
duration superimposed on Izt
NOTE 4 Voltage measurements to be performed 90 seconds after application of DC current.
DL4728A thru DL4761A
Revision: C 2012/08/23
TM
Micro Commercial Components
www.mccsemi.com
2 of 3
MCC
MCC
Revision: C 2012/08/23
TM
Micro Commercial Components
www.mccsemi.com
3 of 3
3
Device Packing
Part Number-TP Tape&Reel: 5Kpcs/Reel
Ordering Information :
***IMPORTANT NOTICE***
Micro Commercial Components Corp. reserves the right to make changes without further notice to any product herein to
make corrections, modifications , enhancements , improvements , or other changes . Micro Commercial Components
Corp . does not assume any liability arising out of the application or use of any product described herein; neither does it
convey any license under its patent rights ,nor the rights of others . The user of products in such applications shall assume all
risks of such use and will agree to hold Micro Commercial Components Corp . and all the companies whose products are
represented on our website, harmless against all damages.
***LIFE SUPPORT***
MCC's products are not authorized for use as critical components in life support devices or systems without the express written
approval of Micro Commercial Components Corporation.
***CUSTOMER AWARENESS***
Counterfeiting of semiconductor parts is a growing problem in the industry. Micro Commercial Components (MCC) is taking
strong measures to protect ourselves and our customers from the proliferation of counterfeit parts. MCC strongly encourages
customers to purchase MCC parts either directly from MCC or from Authorized MCC Distributors who are listed by country on
our web page cited below. Products customers buy either from MCC directly or from Authorized MCC Distributors are genuine
parts, have full traceability, meet MCC's quality standards for handling and storage. MCC will not provide any warranty
coverage or other assistance for parts bought from Unauthorized Sources. MCC is committed to combat this global
problem and encourage our customers to do their part in stopping this practice by buying direct or from authorized
distributors.
