LM5041 LM5041 Cascaded PWM Controller Literature Number: SNVS248C LM5041 Cascaded PWM Controller General Description Features The LM5041 PWM controller contains all of the features necessary to implement either current-fed or voltage-fed push-pull or bridge power converters. These "Cascaded" topologies are well suited for multiple output and higher power applications. The LM5041's four control outputs include: the buck stage controls (HD and LD) and the pushpull control outputs (PUSH and PULL). Push-pull outputs are driven at 50% nominal duty cycle at one half of the switching frequency of the buck stage and can be configured for either a guaranteed overlap time (for current-fed applications) or a guaranteed both-off time (for voltage-fed applications). Push-pull stage MOSFETs can be driven directly from the internal gate drivers while the buck stage requires an external driver such as the LM5102. The LM5041 includes a high-voltage start-up regulator that operates over a wide input range of 15V to 100V. The PWM controller is designed for high-speed capability including an oscillator frequency range up to 1 MHz and total propagation delays of less than 100ns. Additional features include: line Under-Voltage Lockout (UVLO), soft-start, an error amplifier, precision voltage reference, and thermal shutdown. n Internal Start-up Bias Regulator n Programmable Line Under-Voltage Lockout (UVLO) with Adjustable Hysteresis n Current Mode Control n Internal Error Amplifier with Reference n Dual Mode Over-Current Protection n Leading Edge Blanking n Programmable Push-Pull Overlap or Dead Time n Internal 1.5A Push-Pull Gate Drivers n Programmable Soft-start n Programmable Oscillator with Sync Capability n Precision Reference n Thermal Shutdown Applications n n n n Telecommunication Power Converters Industrial Power Converters Multi-Output Power Converters +42V Automotive Systems Packages n TSSOP-16 n LLP-16 (5x5 mm) Thermally Enhanced Typical Application Circuit 20074901 Simplified Cascaded Push-Pull Power Converter (c) 2004 National Semiconductor Corporation DS200749 www.national.com LM5041 Cascaded PWM Controller April 2004 LM5041 Connection Diagram 20074902 16-Lead TSSOP, LLP Ordering Information Order Number Package Type NSC Package Drawing Supplied As LM5041MTC TSSOP-16 MTC-16 92 Units per anti-static tube LM5041MTCX TSSOP-16 MTC-16 2500 Units on Tape and Reel LM5041SD LLP-16 SDA-16A 1000 Units on Tape and Reel LM5041SDX LLP-16 SDA-16A 4500 Units on Tape and Reel Pin Description PIN NAME 1 VIN Source Input Voltage Input to start-up regulator. Input range 15V to 100V. 2 FB Feedback Signal Inverting input for the internal error amplifier. The non-inverting input is connected to a 0.75V reference. 3 COMP Output of the Internal Error Amplifier There is an internal 5k resistor pull-up on this pin. The error amplifier provides an active sink. 4 REF Precision 5 volt reference output Maximum output current: 10mA. Locally decouple with a 0.1F capacitor. Reference stays low until the line UV and the VCC UV are satisfied. 5 HD Main Buck PWM control output Buck switch PWM control output. The maximum duty cycle clamp for this output corresponds to an off time of typically 240ns per cycle. The LM5101 or LM5102 Buck stage gate driver can be used to level shift and drive the Buck switch. 6 LD Sync Switch control output Sync Switch control output. Inversion of HD output. The LM5101 or LM5102 lower drive can be used to drive the synchronous rectifier switch. 7 VCC Output from the internal high voltage start-up If an auxiliary winding raises the voltage on this pin regulator. Regulated to 9 volts. above the regulation setpoint, the internal start-up regulator will shutdown, reducing the IC power dissipation. 8 PUSH www.national.com DESCRIPTION APPLICATION INFORMATION Output of the push-pull drivers Output of the push-pull gate driver. Output capability of 1.5A peak . 2 LM5041 Pin Description (Continued) PIN NAME DESCRIPTION 9 PULL Output of the push-pull drivers APPLICATION INFORMATION 10 PGND Power ground Connect directly to analog ground. 11 AGND Analog ground Connect directly to power ground. 12 CS Current sense input Current sense input to the PWM comparator (CM control). There is a 50ns leading edge blanking on this pin. Using separate dedicated comparators, if CS exceeds 0.5V the outputs will go into cycle by cycle current limit. If CS exceeds 0.6V the outputs will be disabled and a soft-start commenced. 13 SS Soft-start control An external capacitor and an internal 10uA current source, set the soft-start ramp. The controller will enter a low power state if the SS pin is below the shutdown threshold of 0.45V 14 TIME Push-Pull overlap and dead time control An external resistor (RSET) sets the overlap time or dead time for the push-pull outputs. A resistor connected between TIME and GND produces overlap. A resistor connected between TIME and REF produces dead time. 15 RT / SYNC Oscillator timing resistor pin and sync An external resistor sets the oscillator frequency. This pin will also accept an external oscillator. 16 UVLO Line Under-Voltage Shutdown An external divider from the power converter source sets the shutdown levels. Threshold of operation equals 2.5V. Hysteresis is set by a switched internal current source (20A). LLP DAP SUB Die substrate The exposed die attach pad on the LLP package should be connected to a PCB thermal pad at ground potential. For additional information on using National Semiconductor's No Pull Back LLP package, please refer to LLP Application Note AN-1187. Output of the push-pull gate driver. Output capability of 1.5A peak. 3 www.national.com LM5041 Block Diagram Simplified Block Diagram 20074903 www.national.com 4 ESD Rating If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Lead temperature (Note 2) VIN to GND 100V VCC to GND 16V All Other Inputs to GND -0.3 to 7V Junction Temperature 150C Storage Temperature Range -65C to +150C LM5041 Absolute Maximum Ratings (Note 1) 2 kV Wave 4 seconds 260C Infrared 10 seconds 240C Vapor Phase 75 seconds 219C Operating Ratings (Note 1) 15 to 90V VIN Junction Temperature -40C to +125C Electrical Characteristics Specifications with standard typeface are for TJ = 25C, and those with boldface type apply over full Operating Junction Temperature range. VIN = 48V, VCC = 10V, RT = 26.7k, RSET = 20k) unless otherwise stated (Note 3) Symbol Parameter Conditions Min Typ Max 9.3 Units Startup Regulator VCC Reg I-VIN VCC Regulation open circuit 8.7 9 VCC Current Limit (Note 4) 15 25 V Startup Regulator Leakage (external Vcc Supply) VIN = 100V 145 500 A Shutdown Current (Iin) UVLO = 0V, VCC = open 350 450 A mA VCC Supply VCC Under-voltage Lockout Voltage (positive going Vcc) VCC Reg - 400mV VCC Reg 275mV VCC Under-voltage Hysteresis 1.7 2.1 2.6 V 3 4 mA Supply Current (ICC) CL = 0 V Error Amplifier GBW Gain Bandwidth 3 MHz DC Gain 80 dB Input Voltage VFB = COMP COMP Sink Capability VFB = 1.5V, COMP= 1V 0.735 0.75 4 8 0.765 V mA Reference Supply VREF Ref Voltage IREF = 0 mA Ref Voltage Regulation IREF = 0 to 10mA 4.85 Ref Current Limit 15 5 5.15 V 25 50 mV 20 mA 40 ns Current Limit ILIM Delay to Output CS Step from 0 to 0.6V Time to Onset of OUT Transition (90%) CL = 0 Cycle by Cycle Threshold Voltage Cycle Skip Threshold Voltage Resets SS capacitor; auto restart 0.45 0.5 0.55 V 0.55 0.6 0.65 V Leading Edge Blanking Time CS Sink Current (clocked) CS = 0.3V 2 5 50 ns 5 mA www.national.com LM5041 Electrical Characteristics (Continued) Specifications with standard typeface are for TJ = 25C, and those with boldface type apply over full Operating Junction Temperature range. VIN = 48V, VCC = 10V, RT = 26.7k, RSET = 20k) unless otherwise stated (Note 3) Symbol Parameter Conditions Min Typ Max Units 7 10 13 A Soft-start to COMP Offset 0.35 0.55 0.75 V Shutdown Threshold 0.25 0.5 0.75 V 180 175 200 220 225 kHz 515 600 685 kHz 3 3.5 V Soft-Start Soft-start Current Source Oscillator Frequency1 (RT = 26.7K) TJ = 25C Frequency2 (RT = 7.87K) Sync threshold PWM Comparator Delay to Output COMP set to 2V CS stepped 0 to 0.4V, Time to onset of OUT transition low 25 ns Max Duty Cycle TS = Oscillator Period (Ts-240ns)/Ts) % Min Duty Cycle COMP = 0V COMP to PWM Comparator Gain 0 % 0.32 COMP Open Circuit Voltage FB = 0V 4.1 4.8 5.5 V COMP Short Circuit Current FB = 0V, COMP = 0V 0.6 1 1.4 mA Slope Compensation Slope Comp Amplitude Delta increase at PWM Comparator to CS 110 mV UVLO Shutdown Under-voltage Shutdown Under-voltage Shutdown Hysteresis Current Source 2.44 2.5 2.56 V 16 20 24 A Buck Stage Outputs 5 (VREF) Output High level V Output High Saturation IOUT = 10mA REF = VOUT 0.5 1 Output Low Saturation IOUT = -10mA 0.5 1 Rise Time CL = 100pF 10 ns Fall Time CL = 100pF 10 ns V V Push-Pull Outputs www.national.com Overlap Time RSET = 20k Connected to GND, 50% to 50% Transitions 60 90 120 ns Dead Time RSET = 20k Connected to REF, 50% to 50% Transitions 65 95 125 ns 6 (Continued) Specifications with standard typeface are for TJ = 25C, and those with boldface type apply over full Operating Junction Temperature range. VIN = 48V, VCC = 10V, RT = 26.7k, RSET = 20k) unless otherwise stated (Note 3) Symbol Typ Max Units Output High Saturation Parameter IOUT = 50mA VCC - VOUT Conditions Min 0.25 0.5 V Output Low Saturation IOUT = 100mA 0.5 1 Rise Time CL = 1nF 20 ns Fall Time CL = 1nF 20 ns Thermal Shutdown Temp. 165 C Thermal Shutdown Hysteresis 25 C MTC Package 125 C/W SDA Package 32 C/W V Thermal Shutdown TSD Thermal Resistance JA Junction to Ambient Note 1: Absolute Maximum Ratings are limits beyond which damage to the device may occur. Operating Ratings are conditions under which operation of the device is intended to be functional. For guaranteed specifications and test conditions, see the Electrical Characteristics. Note 2: For detailed information on soldering plastic TSSOP and LLP packages, refer to the Packaging Data Book available from National Semiconductor Corporation. Note 3: All limits are guaranteed. All electrical characteristics having room temperature limits are tested during production with TA = TJ = 25C. All hot and cold limits are guaranteed by correlating the electrical characteristics to process and temperature variations and applying statistical process control. Note 4: Device thermal limitations may limit usable range. 7 www.national.com LM5041 Electrical Characteristics LM5041 Typical Performance Characteristics VCC and VIN vs VIN VCC vs ICC 20074909 20074908 SS Pin Current vs Temp Frequency vs RT 20074910 20074915 Overlap Time vs RSET Dead Time vs RSET 20074912 20074911 www.national.com 8 LM5041 Typical Performance Characteristics (Continued) Overlap Time vs Temp Dead Time vs Temp 20074913 20074914 Error Amplifier Gain Phase 20074916 9 www.national.com LM5041 ground sets the operational range of the converter. The divider must be designed such that the voltage at the UVLO pin will be greater than 2.5V when VIN is in the desired operating range. If the Under-Voltage threshold is not met, all functions of the controller are disabled and the controller will enter a low-power state with input current < 300A. ULVO hysteresis is accomplished with an internal 20A current source that is switched on or off into the impedance of the set-point divider. When the UVLO threshold is exceeded, the current source is activated to instantly raise the voltage at the UVLO pin. When the UVLO pin falls below the 2.5V threshold, the current source is turned off causing the voltage at the UVLO pin to fall. The UVLO pin can also be used to implement a remote enable / disable function. By shorting the UVLO pin to ground, the converter can be disabled. The controller can also be disabled through the soft-start pin (SS). The controller will enter a low-power off state if the SS pin is forced below the 0.45V shutdown threshold. Detailed Operating Description The LM5041 PWM controller contains all of the features necessary to implement either current-fed or voltage-fed push-pull or bridge power converters. These "Cascaded" topologies are well suited for multiple output and higher power applications. The LM5041's four control outputs include: the buck stage controls (HD and LD) and the pushpull control outputs (PUSH and PULL). Push-pull outputs are driven at 50% nominal duty cycle at one half of the switching frequency of the buck stage and can be configured for either a guaranteed overlap time (for current-fed applications) or a guaranteed both-off time (for voltage-fed applications). Push-pull stage MOSFETs can be driven directly from the internal gate drivers while the buck stage requires an external driver such as the LM5102. The LM5041 includes a high-voltage start-up regulator that operates over a wide input range of 15V to 100V. The PWM controller is designed for high-speed capability including an oscillator frequency range up to 1 MHz and total propagation delays of less than 100ns. Additional features include: line Under-Voltage Lockout (UVLO), soft-start, an error amplifier, precision voltage reference, and thermal shutdown. Buck Stage Control Outputs The LM5041 Buck switch maximum duty cycle clamp ensures that there will be sufficient off time each cycle to recharge the bootstrap capacitor used in the high side gate driver. The Buck switch is guaranteed to be off, and the sync switch on, for at least 250ns per switching cycle. The Buck stage control outputs (LD and HD) are CMOS buffers with logic levels of 0 to 5V. During any fault state or Under-Voltage off state, the buck stage control outputs will default to HD low and LD high. High Voltage Start-Up Regulator The LM5041 contains an internal high-voltage start-up regulator, thus the input pin (Vin) can be connected directly to the line voltage. The regulator output is internally current limited to 15mA. When power is applied, the regulator is enabled and sources current into an external capacitor connected to the Vcc pin. The recommended capacitance range for the Vcc regulator is 0.1uF to 100uF. When the voltage on the Vcc pin reaches the regulation point of 9V and the internal voltage reference (REF) reaches its regulation point of 5V, the controller outputs are enabled. The Buck stage outputs will remain enabled until Vcc falls below 7V or the line Under-Voltage Lockout detector indicates that Vin is out of range. The push-pull outputs continue switching until the REF pin voltage falls below approximately 3V. In typical applications, an auxiliary transformer winding is connected through a diode to the Vcc pin. This winding must raise the Vcc voltage above 9.3V to shut off the internal start-up regulator. Powering VCC from an auxiliary winding improves efficiency while reducing the controller's power dissipation. The recommended capacitance range for the Vref regulator output is 0.1uF to 10uF. The external VCC capacitor must be sized such that the capacitor maintains a VCC voltage greater than 7V during the initial start-up. During a fault mode when the converter auxiliary winding is inactive, external current draw on the VCC line should be limited so the power dissipated in the start-up regulator does not exceed the maximum power dissipation of the controller. An external start-up or other bias rail can be used instead of the internal start-up regulator by connecting the VCC and the VIN pins together and feeding the external bias voltage into the two pins. Push-Pull Outputs The push pull outputs operate continuously at a nominal 50% duty cycle. A distinguishing feature of the LM5041 is the ability to accurately configure either dead time (both-off) or overlap time (both-on) on the complementary push-pull outputs. The overlap/dead time magnitude is controlled by a resistor connected to the TIME pin on the controller. The TIME pin holds one end of the resistor at 2.5V and the other end of the resistor should be connected to either REF for dead time control setting or to GND for overlap control. The polarity of the current in the TIME is detected by the LM5041 The magnitude of the overlap/dead time can be calculated as follows: Overlap Time (ns) = (3.66 x RSET) + 7 Overlap Time in ns, RSET connected to GND, RSET in k Dead Time (ns) = (3.69 x RSET) + 21 Dead Time in ns, RSET connected to REF, RSET in k Recommended RSET programming range: 10k to 100k Current-fed designs require a period of overlap to insure there is a continuous path for the buck inductor current. Voltage-fed designs require a period of dead time to insure there is no time when the push-pull transformer acts as a shorted turn to the low impedance sourcing node. The pushpull outputs alternate continuously under all conditions provided REF the voltage is greater than 3V. Line Under-Voltage Detector The LM5041 contains a line Under-Voltage Lockout (UVLO) circuit. An external set-point resistor divider from VIN to www.national.com 10 LM5041 Push-Pull Outputs (Continued) 20074904 must be placed close to the device and connected directly to the pins of the controller (CS and GND). If a current sense transformer is used, both leads of the transformer secondary should be routed to the sense resistor, which should also be located close to the IC. A resistor may be used for current sensing instead of a transformer, located in the push-pull transistor sources, but a low inductance type of resistor is required. When designing with a sense resistor, all of the noise sensitive low power grounds should be connected together around the IC and a single connection should be made to the high current power ground (sense resistor ground point). The second level current sense threshold is intended to protect the power converter by initiating a low duty cycle hick-up mode when abnormally high currents are sensed. If the second level threshold is reached, the soft-start capacitor will be discharged and a start-up sequence will commence when the soft-start capacitor is determined to be fully discharged. The second level threshold will only be reached when a high dV/dt is present at the current sense pin. The current sense transient must be fast enough to reach the second level threshold before the first threshold detector turns off the buck stage driver. Very high current sense dV/dt can occur with a saturated power inductor or shorted load. Excessive filtering on the CS pin such as an extremely low value current sense resistor or an inductor that does not saturate with excessive loading, may prevent the second level threshold from being reached. If the second level threshold is never exceeded during an overload condition, the first level current sense will continue cycle by cycle limiting and the output characteristic of the converter will be that of a current source. However, a sustained overload current level can cause excessive temperatures in the power train especially the output rectifiers. PWM Comparator The PWM comparator compares the slope compensated current ramp signal to the loop error voltage from the internal error amplifier (COMP pin). This comparator is optimized for speed in order to achieve minimum controllable duty cycles. The comparator polarity is such that 0V on the COMP pin will produce zero duty cycle in the buck stage. Error Amplifier An internal high gain wide-bandwidth error amplifier is provided within the LM5041. The amplifier's non-inverting input is tied to a 0.75V reference. The inverting input is connected to the FB pin. In non-isolated applications the power converter output is connected to the FB pin via the voltage setting resistors. Loop compensation components are connected between the COMP and FB pins. For most isolated applications the error amplifier function is implemented on the secondary side of the converter and the internal error amp is not used. The internal error amplifier is configured as an open drain output and can be disabled by connecting the FB pin to ground. An internal 5k pull-up resistor between the 5V reference and COMP can be used as the pull-up for an opto-coupler in isolated applications. Current Limit/Current Sense The LM5041 contains two levels of over-current protection. If the voltage at the CS pin exceeds 0.5V the present buck stage duty cycle is terminated (cycle by cycle current limit). If the voltage at the CS pin overshoots the 0.5V threshold and exceeds 0.6V, then the controller will terminate the present cycle and fully discharge the soft-start capacitor. A small RC filter located near the controller is recommended to filter current sense signals at the CS pin. An internal MOSFET discharges the external CS pin for an additional 50ns at the beginning of each cycle to reduce the leading edge spike that occurs when the buck stage MOSFET is turned on. The LM5041 current sense and PWM comparators are very fast, and may respond to short duration noise pulses. Layout considerations are critical for the current sense filter and sense resistor. The capacitor associated with the CS filter Oscillator and Sync Capability The LM5041 oscillator is set by a single external resistor connected between the RT pin and GND. To set a desired oscillator frequency (F), the necessary RT resistor can be calculated from: 11 www.national.com LM5041 Oscillator and Sync Capability ramp and summing a current ramp generated by the oscillator internally with the current sense signal. Additional slope compensation may be provided by increasing the source impedance of the current sense signal. (Continued) Soft-start and Shutdown The soft-start feature allows the power converter to gradually reach the initial steady state operating point, thereby reducing start-up stresses and surges. At power on, a 10uA current is sourced out of the soft-start pin (SS) to charge an external capacitor. The capacitor voltage will ramp up slowly and will limit the maximum duty cycle of the buck stage. In the event of a fault as indicated by VCC Under-voltage, line Under-voltage or second level current limit, the output drivers are disabled and the soft-start capacitor is discharged to ground. When the fault condition is no longer present, a soft-start sequence will begin again and buck stage duty cycle will gradually increase as the soft-start capacitor is charged. The SS pin also serves as an enable input. The controller will enter a low power state if the SS pin is forced below the 0.45V threshold. The buck stage will switch at the oscillator frequency and each push-pull output will switch at half the oscillator frequency in a push-pull configuration. The LM5041 can also be synchronized to an external clock. The external clock must have a higher frequency than the free running frequency set by the RT resistor. The clock signal should be capacitively coupled into the RT pin with a 100pF capacitor. A peak voltage level greater than 3V is required for detection of the sync pulse. The sync pulse width should be set in the 15 to 150ns range by the external components. The RT resistor is always required, whether the oscillator is free running or externally synchronized. The voltage at the RT pin is internally regulated to 2V. The RT resistor should be located very close to the device and connected directly to the pins of the IC (RT and GND). Thermal Protection Slope Compensation Internal Thermal Shutdown circuitry is provided to protect the integrated circuit in the event that the maximum junction temperature is exceeded. When activated, typically at 165 degrees Celsius, the controller is forced into a low-power standby state, disabling the output drivers and the bias regulator. This feature is provided to prevent catastrophic failures from accidental device overheating. The PWM comparator compares the current sense signal to the voltage at the COMP pin. The output stage of the internal error amplifier generally drives the COMP pin. At duty cycles greater than 50 percent, current mode control circuits are subject to sub-harmonic oscillation. By adding an additional fixed ramp signal (slope compensation) to the current sense ramp, oscillations can be avoided. The LM5041 integrates this slope compensation by buffering the internal oscillator www.national.com 12 LM5041 Typical Application 20074906 FIGURE 1. Simplified Cascaded Half-Bridge 13 www.national.com www.national.com 14 Application Circuit: Input 35-80V, Output 2.5V, 50A 20074907 LM5041 LM5041 Physical Dimensions inches (millimeters) unless otherwise noted Molded TSSOP-16 NS Package Number MTC16 16-Lead LLP Surface Mount Package NS Package Number SDA16A 15 www.national.com LM5041 Cascaded PWM Controller Notes LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. BANNED SUBSTANCE COMPLIANCE National Semiconductor certifies that the products and packing materials meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ``Banned Substances'' as defined in CSP-9-111S2. National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated