9900 Dual Output Hall Effect Sensor Fully Redundant, Non-Contacting Rotary Series The BEI Sensors 9900 Series offers a non-contacting Hall effect sensor in a rugged design, ideally suited for tight packaging constraints while providing superior reliability and durability. Unlike most similar products, the 9900 provide the full redundancy of two independent Hall detectors in a common package (single output sensors also available). Each Hall detector is rigidly supported to meet the severe durability requirements of demanding applications as automotive and off-highway. Rotating sintered magnets enable the stationary detectors to perform with improved accuracy and reliability, including excellent temperature stability and corrosion resistance. One-time factory programmability allows for greater flexibility in design and custom outputs. Fully sealed, (meeting and/or exceeding IP66/IP67 standards) the 9900 is impervious to contamination and moisture. An integrally molded, 6-pin connector makes a sealed connection with industry standard Packard Electric connectors. MECHANICAL 9900 Series Features: SENSOR 1 * Rotating magnet/Fixed sensor configuration Provides improved accuracy and reliability Two independent outputs for redundancy Full redundancy assures back-up safety SENSOR 2 * Fully programmable Outputs; offset, gain, slope and temperature compensation Sintered Alnico-8 magnets Provide excellent temperature stability and corrosion resistance * OTHER OPTIONS AVAILABLE Ratiometric Output Factory programming through connector After completion of assembly provides high accuracy Sealed construction IP66/IP67, 6-pin I/O Interface to Packard Electric Connector Extended temperature range -40 to +150C available optionally Return spring (CW standard, CCW optional) Eliminates mechanical backlash Extended operating life 35 million operational cycles Ordering Information: 990X XXX XX XX Temperature Rating: Blank = Standard 85C, HT = 125C Spring Return: CW = Clockwise, CCW = Counter Clockwise, NS = No Spring Return Electrical Angle: ie. 090 = 45, 120 = 60 Number of Sensors: 1 = Single Output, 2 = Dual Output SAMPLE: 9902 090 CW Standard 85C CW = Clockwise Spring Return 90 (45) Electrical Angle Dual Output 15771 Red Hill Avenue Tustin, CA 92780-7303 (714) 258-7500 Fax: (714) 258-8120 email: sales@beiduncan.com ISO9001 Certified/QS9000 Registered Dual Output Hall Effect Sensor 9900 Series Dual Output Hall Effect Sensor 9900 Series 1 2 Connector mates with Packard Electric METRI-Pack 150.2 series (pull-to-seat 6 pin sealed connector assemblies) (i.e. 12162261, 12162260 or 12162210) Shaft flat is shown with: sensor 1 output at 50% Vs (input voltage). sensor 2 output at 25% Vs (input voltage). CONNECTOR PIN OUTPUT Vs (input) GROUND OUTPUT SENSOR 1 F E C SENSOR 2 B A D NOTE: All dimensions are shown in millimeters. (Typical Sensor Output) Mechanical Specifications Mechanical Travel Frequency Response Rotational Torque Weight -90 to +90 (180 total rotation) 1,000Hz minimum 0.025 - 0.110 N-m 35 grams (approx.) Electrical Specifications Mechanical Input Range -45 to +45 (other angles available) Input Voltage Input Current 5.0 V 0.25V DC 10mA maximum per output 20mA maximum total 0.5V - 4.5V 0.25V - 2.25V (Different output voltage range for sensor outputs available as a custom option) 2.0% of full scale at room temperature 3.0% of full scale over operating temperature range Analog (continuous) Sensor 1 Output Sensor 2 Output Accuracy Resolution Environmental Specifications Electromagnetic Compatibility Vibration Shock Side Load Operating temperature range Storage temperature range 100V/meter, 14kHz - 1GHz range 10G peak, 20 - 2,000 Hz 50Gs, half sine pulse, 5 m sec duration 1kg for 1 million cycles -40C to +85 C (wider operating temperature -40 to +150C available as a custom option) -55C to +105C (-55C to +165C) Specifications subject to change without notice. BE2023 15771 Red Hill Avenue Tustin, CA 92780-7303 (714) 258-7500 Fax: (714) 258-8120 email: sales@beiduncan.com ISO9001 Certified/QS9000 Registered