BQ25101HYFPT - Texas Instruments - Datasheet.Directory

VBUS

GND

HOST

bq25100

OUT

1ÛF1ÛF

SYSTEM

D+

D-

USB Port or

Adapter

ISET

PRETERM

TEMP PACK+

PACK-

VSS

1.35k

6k

Product

Folder

Sample &

Buy

Technical

Documents

Tools &

Software

Support &

Community

bq25100

bq25101

bq25100A

bq25100H

bq25101H

bq25100L

SLUSBV8C –AUGUST 2014–REVISED NOVEMBER 2014

bq2510x 250-mA Single Cell Li-Ion Battery Chargers, 1-mA Termination, 75-nA Battery

Leakage

1 Features 3 Description

The bq2510x series of devices are highly integrated

1• Charging Li-Ion and Li-Pol linear chargers targeted at space-

– 1% Charge Voltage Accuracy limited portable applications. The high input voltage

– 10% Charge Current Accuracy range with input overvoltage protection supports low-

cost unregulated adapters.

– Supports Applications for Very Low Charge

Currents - 10 mA to 250 mA The bq2510x has a single power output that charges

the battery. A system load can be placed in parallel

– Supports minimum 1-mA Charge Termination with the battery as long as the average system load

Current does not keep the battery from charging fully during

– Ultra Low Battery Output Leakage Current - the 10 hour safety timer.

Maximum 75 nA The battery is charged in three phases: conditioning,

– Adjustable Termination and Precharge constant current and constant voltage. In all charge

Threshold phases, an internal control loop monitors the IC

– High voltage Chemistry Support: 4.35 V with junction temperature and reduces the charge current

bq25100H/01H, 4.30 V with bq25100A if an internal temperature threshold is exceeded.

• Protection The charger power stage and charge current sense

– 30-V Input Rating; with 6.5-V Input functions are fully integrated. The charger function

Overvoltage Protection has high accuracy current and voltage regulation

loops and charge termination. The pre-charge current

– Input Voltage Dynamic Power Management and termination current threshold are programmed

– 125°C Thermal Regulation; 150°C Thermal via an external resistor on the bq2510x. The fast

Shutdown Protection charge current value is also programmable via an

– OUT Short-Circuit Protection and ISET Short external resistor.

Detection Device Information(1)

– Operation over JEITA Range via Battery PART NUMBER PACKAGE BODY SIZE (NOM)

NTC – 1/2 Fast-Charge-Current at Cold, 4.06 bq25100 DSBGA (6) 1.60 mm × 0.90 mm

V (bq25100/01) or 4.2 V (bq25100H/01H) at bq25101 DSBGA (6) 1.60 mm × 0.90 mm

Hot bq25100A DSBGA (6) 1.60 mm × 0.90 mm

– Fixed 10 Hour Safety Timer bq25100H DSBGA (6) 1.60 mm × 0.90 mm

• System bq25101H DSBGA (6) 1.60 mm × 0.90 mm

– Automatic Termination and Timer Disable bq25100L(2) DSBGA (6) 1.60 mm × 0.90 mm

Mode (TTDM) for Absent Battery Pack (1) For all available packages, see the orderable addendum at

– Available in Small 1.60 mm × 0.90 mm the end of the datasheet.

DSBGA Package (2) Product preview. Contact the local TI representative for device

details.

2 Applications

• Fitness Accessories

• Smart Watches

• Bluetooth®Headsets

• Low-Power Handheld Devices

An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,

intellectual property matters and other important disclaimers. UNLESS OTHERWISE NOTED, this document contains PRODUCTION

DATA.

bq25100

bq25101

bq25100A

bq25100H

bq25101H

bq25100L

SLUSBV8C –AUGUST 2014–REVISED NOVEMBER 2014

www.ti.com

Table of Contents

1 Features.................................................................. 19 Application and Implementation ........................ 22

9.1 Application Information............................................ 22

2 Applications ........................................................... 19.2 Typical Application - Charger Application Design

3 Description............................................................. 1Example................................................................... 22

4 Revision History..................................................... 210 Power Supply Recommendations ..................... 24

5 Device Comparison Table..................................... 310.1 Leakage Current Effects on Battery Capacity....... 24

6 Pin Configuration and Functions......................... 311 Layout................................................................... 24

7 Specifications......................................................... 411.1 Layout Guidelines ................................................. 24

7.1 Absolute Maximum Ratings .................................... 411.2 Layout Example .................................................... 25

7.2 Handling Ratings....................................................... 411.3 Thermal Package.................................................. 25

7.3 Recommended Operating Conditions ..................... 412 Device and Documentation Support................. 26

7.4 Thermal Information.................................................. 412.1 Device Support .................................................... 26

7.5 Electrical Characteristics.......................................... 512.2 Related Links ........................................................ 26

7.6 Typical Characteristics.............................................. 812.3 Trademarks........................................................... 26

8 Detailed Description............................................ 12 12.4 Electrostatic Discharge Caution............................ 26

8.1 Overview................................................................. 12 12.5 Glossary................................................................ 26

8.2 Functional Block Diagram....................................... 14 13 Mechanical, Packaging, and Orderable

8.3 Feature Description................................................. 15 Information ........................................................... 26

8.4 Device Functional Modes........................................ 18

4 Revision History

NOTE: Page numbers for previous revisions may differ from page numbers in the current version.

Changes from Revision B (October 2014) to Revision C Page

• Changed data sheet title ........................................................................................................................................................ 1

• Deleted product preview note from bq25101H in Device Information Table.......................................................................... 1

• Deleted product preview note from bq25101H in Device Comparison Table ....................................................................... 3

Changes from Revision A (September 2014) to Revision B Page

• Deleted product preview note from bq25101 and bq25100H in Device Information Table.................................................... 1

• Deleted product preview note from bq25101 and bq25100H in Device Comparison Table ................................................. 3

Changes from Original (August 2014) to Revision A Page

• Release to Production............................................................................................................................................................ 1

Product Folder Links: bq25100 bq25101 bq25100A bq25100H bq25101H bq25100L

OUT IN

TS ISET

CHG VSS

1 2

bq25101/101H

OUT IN

TS ISET

PRE-

TERM VSS

1 2

bq25100/100A/100H/100L

bq25100

bq25101

bq25100A

bq25100H

bq25101H

bq25100L

www.ti.com

SLUSBV8C –AUGUST 2014–REVISED NOVEMBER 2014

5 Device Comparison Table

PART NUMBER VO(REG) VOVP PreTerm /CHG TS

bq25100 4.20 V 6.5 V PreTerm TS (JEITA)

bq25101 4.20 V 6.5 V CHG TS (JEITA)

bq25100A 4.30 V 6.5 V PreTerm TS

bq25100H 4.35 V 6.5 V PreTerm TS (JEITA)

bq25101H 4.35 V 6.5 V CHG TS (JEITA)

bq25100L(1) 4.06 V 6.5V PreTerm TS

(1) Product preview. Contact the local TI representative for device details.

6 Pin Configuration and Functions SPACING

6-Pin DSBGA 6-Pin DSBGA

YFP Package YFP Package

(Top View) (Top View)

Pin Functions

PIN I/O DESCRIPTION

NAME NUMBER

CHG C1(1) Low (FET on) indicates charging and open drain (FET off) indicates no charging or the first charge

cycle complete.

Input power, connected to external DC supply (AC adapter or USB port). Expected range of bypass

IN A2 I capacitors 1 μF to 10 μF, connect from IN to VSS.

Programs the fast-charge current setting. External resistor from ISET to VSS defines fast charge

ISET B2 I current value. Recommended range is 13.5 kΩ(10 mA) to 0.54 kΩ(250 mA).

Battery Connection. System Load may be connected. Expected range of bypass capacitors 1 μF to

OUT A1 O 10 μF.

Programs the current termination threshold ( 1% to 50% of Iout, 1mA minimum). The pre-charge

PRE-TERM C1(1) Icurrent is twice the termination current level.

Expected range of programming resistor is 600 Ωto 30 kΩ(6k: Ichg/10 for term; Ichg/5 for

precharge)

Temperature sense pin connected to 10k at 25°C NTC thermistor, in the battery pack. Floating TS

pin or pulling high puts part in TTDM “Charger” mode and disables TS monitoring, Timers and

TS B1 I Termination. Pulling pin low disables the IC. If NTC sensing is not needed, connect this pin to VSS

through an external 10-kΩresistor. A 250-kΩresistor from TS to ground will prevent IC entering

TTDM mode when battery with thermistor is removed.

VSS C2 – Ground pin

(1) Spins have different pin definitions

Product Folder Links: bq25100 bq25101 bq25100A bq25100H bq25101H bq25100L

bq25100

bq25101

bq25100A

bq25100H

bq25101H

bq25100L

SLUSBV8C –AUGUST 2014–REVISED NOVEMBER 2014

www.ti.com

7 Specifications

7.1 Absolute Maximum Ratings(1)

over operating free-air temperature range (unless otherwise noted) MIN MAX UNIT

IN (with respect to VSS) –0.3 30 V

OUT (with respect to VSS) –0.3 7 V

Input voltage PRE-TERM, ISET, TS, CHG –0.3 7 V

(with respect to VSS)

Input current IN 300 mA

Output current (continuous) OUT 300 mA

Output sink current CHG 15 mA

TJJunction temperature –40 150 °C

(1) Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings

only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating

conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. All voltage

values are with respect to the network ground terminal unless otherwise noted.

7.2 Handling Ratings MIN MAX UNIT

ESD Electrostatic discharge IN, OUT, TS 1 µF between IN and GND, 8 kV

(IEC61000-4-2)(1) 1 µF between TS and GND, contact

2 µF between OUT and GND, 15 Air

x5R Ceramic or equivalent

TSTG Storage temperature –65 150 °C

(1) The test was performed on IC pins that may potentially be exposed to the customer at the product level. The bq2510x IC requires a

minimum of the listed capacitance, external to the IC, to pass the ESD test.

7.3 Recommended Operating Conditions (1)

MIN NOM UNIT

IN voltage range 3.5 28 V

VIN IN operating voltage range, Restricted by VDPM and VOVP 4.45 6.45 V

IIN Input current, IN pin 250 mA

IOUT Current, OUT pin 250 mA

TJJunction temperature 0 125 °C

RPRE-TERM Programs precharge and termination current thresholds 0.6 30 kΩ

RISET Fast-charge current programming resistor 0.54 13.5 kΩ

RTS 10k NTC thermistor range without entering BAT_EN or TTDM 1.66 258 kΩ

(1) Operation with VIN less than 4.5V or in drop-out may result in reduced performance.

7.4 Thermal Information bq25100

THERMAL METRIC(1) UNIT

YFP (6 PINS)

RθJA Junction-to-ambient thermal resistance 132.9

RθJCtop Junction-to-case (top) thermal resistance 1.3

RθJB Junction-to-board thermal resistance 21.8 °C/W

ψJT Junction-to-top characterization parameter 5.6

ψJB Junction-to-board characterization parameter 21.8

RθJCbot Junction-to-case (bottom) thermal resistance n/a

(1) For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.

Product Folder Links: bq25100 bq25101 bq25100A bq25100H bq25101H bq25100L

bq25100

bq25101

bq25100A

bq25100H

bq25101H

bq25100L

www.ti.com

SLUSBV8C –AUGUST 2014–REVISED NOVEMBER 2014

7.5 Electrical Characteristics

Over junction temperature range 0°C ≤TJ≤125°C and recommended supply voltage (unless otherwise noted)

PARAMETER TEST CONDITIONS MIN TYP MAX UNIT

INPUT

UVLO Undervoltage lock-out exit VIN: 0 V →4 V 3.15 3.3 3.45 V

VIN: 4 V→0 V;

VHYS_UVLO Hysteresis on VUVLO_RISE falling 250 mV

VUVLO_FALL = VUVLO_RISE – VHYS-UVLO

Input power good detection Input power good if VIN > VOUT + VIN-DT;

VIN-DT 15 60 130 mV

threshold is VOUT + VIN-DT VOUT = 3.6 V; VIN: 3.5 V →4 V

VHYS-INDT Hysteresis on VIN-DT falling VOUT = 3.6 V; VIN: 4 V →3.5 V 31 mV

Time measured from VIN: 0 V →5 V 1-μs rise-

tDGL(PG_PWR) Deglitch time on exiting sleep 29 ms

time to charge enables; VOUT = 3.6 V

Deglitch time on VHYS-INDT power Time measured from VIN: 5 V →3.2 V 1-μs fall-

tDGL(PG_NO-PWR) 29 ms

down. Same as entering sleep. time to charge disables; VOUT = 3.6 V

Input over-voltage protection

VOVP VIN: 5 V →12 V 6.52 6.67 6.82 V

threshold

tDGL(OVP-SET) Input over-voltage blanking time VIN: 5 V →12 V 113 μs

VHYS-OVP Hysteresis on OVP VIN: 11 V →5 V 110 mV

Time measured from VIN: 12 V →5 V 1-μs fall-

tDGL(OVP-REC) Deglitch time exiting OVP 450 μs

time to charge enables

Low input voltage protection. Limit input source current to 50 mA;

VIN-DPM 4.25 4.31 4.37 V

Restricts lout at VIN-DPM VOUT = 3.5 V; RISET = 1.35 kΩ

ISET SHORT CIRCUIT TEST

Highest resistor value considered RISET: 540 Ω → 250 Ω, Iout latches off;

RISET_SHORT 420 450 Ω

a fault (short). Cycle power to reset

Deglitch time transition from ISET Clear fault by disconnecting IN or cycling (high /

tDGL_SHORT 1 ms

short to Iout disable low) TS/BAT_EN

Maximum OUT current limit VIN = 5 V; VOUT = 3.6 V; RISET: 540 Ω → 250 Ω;

IOUT_CL 550 600 650 mA

regulation (Clamp) IOUT latches off after tDGL-SHORT

BATTERY SHORT PROTECTION

OUT pin short-circuit detection

VOUT(SC) VOUT:3 V →0.5 V; No deglitch 0.75 0.8 0.85 V

threshold/ precharge threshold

Recovery ≥VOUT(SC) + VOUT(SC-HYS); Rising; No

VOUT(SC-HYS) OUT pin Short hysteresis 77 mV

deglitch

Source current to OUT pin during

IOUT(SC) 9 11 13 mA

short-circuit detection

QUIESCENT CURRENT

VIN = 0 V; 0°C to 125°C 75

IOUT(PDWN) Battery current into OUT pin nA

VIN = 0 V; 0°C to 85°C 50

OUT pin current, charging

IOUT(DONE) VIN = 6 V; VOUT > VOUT(REG) 6μA

terminated

IIN(STDBY) Standby current into IN pin TS = GND; VIN ≤6 V 125 μA

TS = open, VIN = 6 V;

ICC Active supply current, IN pin TTDM – no load on OUT pin; VOUT > VOUT(REG); 0.75 1 mA

IC enabled

BATTERY CHARGER FAST-CHARGE

TJ= 0°C to 125°C; IOUT = 0 mA to 250 mA; 4.16 4.2 4.23

VIN = 5.0 V; VTS-45°C≤VTS ≤VTS-0°C (bq25100/101)

TJ= 0°C to 125°C; IOUT = 0 mA to 250 mA; 4.26 4.3 4.33

VIN = 5.0 V; VTS-45°C≤VTS ≤VTS-0°C (bq25100A)

VOUT(REG) Output voltage V

TJ= 0°C to 125°C; IOUT = 0 mA to 250 mA;

VIN = 5.0 V; VTS-45°C≤VTS ≤VTS-0°C 4.31 4.35 4.38

(bq25100H/101H)

TJ= -5°C to 55°C; IOUT = 10mA to 75 mA; 4.275 4.3 4.325

VIN = 5.0 V; VTS-45°C≤VTS ≤VTS-0°C (bq25100A)

VIN = 5.0 V; IOUT =10 mA to 250 mA; 4.02 4.06 4.1

VTS-60°C≤VTS ≤VTS-45°C (bq25100/101)

VO_HT(REG) Battery hot regulation voltage V

VIN = 5.0 V; IOUT =10 mA to 250 mA; 4.16 4.2 4.24

VTS-60°C≤VTS ≤VTS-45°C (bq25100H/101H)

Programmed output “fast charge” VOUT(REG) > VOUT > VLOWV; VIN = 5 V;

IOUT(RANGE) 10 250 mA

current range RISET = 0.54 kΩto 13.5 kΩ

Product Folder Links: bq25100 bq25101 bq25100A bq25100H bq25101H bq25100L

bq25100

bq25101

bq25100A

bq25100H

bq25101H

bq25100L

SLUSBV8C –AUGUST 2014–REVISED NOVEMBER 2014

www.ti.com

Electrical Characteristics (continued)

Over junction temperature range 0°C ≤TJ≤125°C and recommended supply voltage (unless otherwise noted)

PARAMETER TEST CONDITIONS MIN TYP MAX UNIT

Adjust VIN down until IOUT = 0.2 A; VOUT = 4.15 V;

VDO(IN-OUT) Drop-Out, VIN – VOUT 220 400 mV

RISET = 680 Ω; TJ≤100°C

IOUT Output “fast charge” formula VOUT(REG) > VOUT > VLOWV; VIN = 5 V KISET/RISET A

RISET = KISET /IOUT; 20 < IOUT < 250 mA 129 135 145

KISET Fast charge current factor AΩ

RISET = KISET /IOUT; 5 < IOUT < 20 mA 125 135 145

PRECHARGE – SET BY PRETERM PIN

Pre-charge to fast-charge

VLOWV 2.4 2.5 2.6 V

transition threshold

Deglitch time on pre-charge to

tDGL1(LOWV) 57 μs

fast-charge transition

Deglitch time on fast-charge to

tDGL2(LOWV) 32 ms

pre-charge transition

IPRE-TERM Refer to the Termination Section

Pre-charge current, default VOUT < VLOWV; RISET = 2.7 kΩ; RPRE-TERM= High Z %IOUT-

18 20 22

setting or for BQ25101/101H CC

%PRECHG Pre-charge current formula RPRE-TERM = KPRE-CHG (Ω/%) × %PRE-CHG (%) RPRE-TERM/KPRE-CHG%

VOUT < VLOWV; VIN = 5 V;

RPRE-TERM = 6 kΩto 30 kΩ;

RISET = 1.8 kΩ; 280 300 320 Ω/%

RPRE-TERM = KPRE-CHG × %IPRE-CHG,

where %IPRE-CHG is 20 to 100%

KPRE-CHG % Pre-charge Factor VOUT < VLOWV; VIN = 5 V;

RPRE-TERM = 3 kΩto 6 kΩ;

RISET = 1.8 kΩ; 265 300 340 Ω/%

RPRE-TERM = KPRE-CHG × %IPRE-CHG,

where %IPRE-CHG is 10% to 20%

TERMINATION – SET BY PRE-TERM PIN

Termination threshold current, VOUT > VRCH; RISET = 2.7 kΩ; RPRE-TERM = High Z %IOUT-

9 10 11

default setting or for BQ25101/101H CC

%TERM Termination current threshold RPRE-TERM = KTERM (Ω/%) × %TERM (%) RPRE-TERM/ KTERM

formula

VOUT > VRCH; VIN = 5 V;

RPRE-TERM = 6 kΩto 30 kΩ;575 600 640

RISET = 1.8 kΩ, RPRE-TERM=KTERM × %ITERM,

where %ITERM is 10 to 50%

VOUT > VRCH; VIN = 5 V;

RPRE-TERM = 3 kΩto 6 kΩ;

KTERM % Term factor 555 620 685 Ω/%

RISET = 1.8 kΩ, RPRE-TERM= KTERM × %ITERM,

where %ITERM is 5 to 10%

VOUT > VRCH; VIN = 5 V;

RPRE-TERM = 750 Ωto 3 kΩ;352 680 1001

RISET = 1.8 kΩ, RPRE-TERM= KTERM × %ITERM,

where %ITERM is 1.25% to 5%

Current for programming the

term. and pre-chg with resistor,

IPRE-TERM RPRE-TERM = 6 kΩ; VOUT = 4.15 V 23 25 27 μA

ITerm-Start is the initial PRE-TERM

current

ITERM Termination current range Minimum absolute termination current 1 mA

%TERM Termination current formula RTERM/ KTERM %

Deglitch time, termination

tDGL(TERM) 29 ms

detected

RECHARGE OR REFRESH

VIN = 5 V; VTS = 0.5 V;

Recharge detection threshold – VOUT: 4.25 V →VRCH (bq25100); VO(REG) VO(REG)–0.0 VO(REG)–0.0 V

normal temp VOUT: 4.35 V →VRCH (bq25100A); –0.125 95 75

VOUT: 4.40 V →VRCH (bq25100H)

VRCH VIN = 5 V; VTS = 0.2 V;

Recharge detection threshold – VO_HT(REG) VO_HT(REG) VO_HT(REG)

VOUT: 4.15 V →VRCH (bq25100); V

hot temp –0.130 –0.105 –0.080

VOUT: 4.25 V →VRCH (bq25100H)

VIN = 5 V; VTS = 0.5 V;

Deglitch time, recharge threshold

tDGL1(RCH) VOUT: 4.25 V →3.5V in 1 μs; 29 ms

detected tDGL(RCH) is time to ISET ramp

Product Folder Links: bq25100 bq25101 bq25100A bq25100H bq25101H bq25100L

bq25100

bq25101

bq25100A

bq25100H

bq25101H

bq25100L

www.ti.com

SLUSBV8C –AUGUST 2014–REVISED NOVEMBER 2014

Electrical Characteristics (continued)

Over junction temperature range 0°C ≤TJ≤125°C and recommended supply voltage (unless otherwise noted)

PARAMETER TEST CONDITIONS MIN TYP MAX UNIT

VIN = 5 V; VTS = 0.5 V;

Deglitch time, recharge threshold

tDGL2(RCH) VOUT = 3.5 V inserted; 29 ms

detected in OUT-Detect Mode tDGL(RCH) is time to ISET ramp

BATTERY DETECT ROUTINE – (NOTE: In Hot mode VO(REG) becomes VO_HT(REG))

bq25100/101/bq25100H/101H; VO(REG)- VO(REG)- VO(REG)-

VIN = 5 V; VTS = 0.5 V, Battery absent 0.450 0.400 0.350

VOUT reduced regulation during

VREG-BD V

battery detect bq25100A; VO(REG)- VO(REG)- VO(REG)-

VIN = 5 V; VTS = 0.5 V; Battery absent 0.550 0.500 0.450

IBD-SINK Sink current during VREG-BD VIN = 5 V; VTS = 0.5 V; Battery absent 2 mA

Regulation time at VREG or VREG-

tDGL(HI/LOW REG) VIN = 5 V; VTS = 0.5 V; Battery absent 25 ms

BD VO(REG) - VO(REG)- VO(REG)-

VBD-HI High battery detection threshold VIN = 5 V; VTS = 0.5 V; Battery absent V

0.150 0.100 0.050

VREG-BD VREG-BD VREG-BD

VBD-LO Low battery detection threshold VIN = 5 V; VTS = 0.5 V; Battery absent V

+0.05 +0.1 +0.15

BATTERY CHARGING TIMERS AND FAULT TIMERS

Restarts when entering pre-charge;

tPRECHG Pre-charge safety timer value 1700 1940 2250 s

Always enabled when in pre-charge.

Clears fault or resets at UVLO, TS disable, OUT

tMAXCH Charge safety timer value 34000 38800 45000 s

Short, exiting LOWV and Refresh

BATTERY-PACK NTC MONITOR (see Note 1); TS pin: 10k NTC

INTC-10k NTC bias current VTS = 0.3 V 48.5 50.5 52.5 μA

10k NTC bias current when

INTC-DIS-10k VTS = 0 V 27 30 33 μA

charging is disabled

INTC is reduced prior to entering

INTC-FLDBK-10k TTDM to keep cold thermistor VTS: Set to 1.525 V 4 5 6.5 μA

from entering TTDM

Termination and timer disable

VTTDM(TS) VTS: 0.5 V →1.7 V; Timer held in reset 1550 1600 1650 mV

mode Threshold – Enter

VHYS-TTDM(TS) Hysteresis exiting TTDM VTS: 1.7 V →0.5 V; Timer enabled 100 mV

VCLAMP(TS) TS maximum voltage clamp VTS = Open (float) 1900 1950 2000 mV

Deglitch exit TTDM between 57 ms

states

tDGL(TTDM) Deglitch enter TTDM between 8μs

states

TS voltage where INTC is reduce INTC adjustment (90 to 10%; 45 to 6.6 uA) takes

VTS_I-FLDBK to keep thermistor from entering place near this spec threshold; 1475 mV

TTDM VTS: 1.425 V →1.525 V

CTS Optional capacitance – ESD 0.22 μF

Low temp charging to pending;

VTS-0°C Low temperature CHG pending 1230 1255 1280 mV

VTS: 1 V →1.5 V

At 0°C;

VHYS-0°C Hysteresis Charge pending to low temp charging; 100 mV

VTS: 1.5 V →1 V

Normal charging to low temp charging;

VTS-10°C Low temperature, half charge 775 800 830 mV

VTS: 0.5 V →1 V

At 10°C;

VHYS-10°C Hysteresis Low temp charging to normal CHG; 55 mV

VTS: 1 V →0.5 V

At 4.1V (bq25100/101) or 4.2V (bq25100H/101H);

VTS-45°C High temperature Normal charging to high temp CHG; 253 268 283 mV

VTS: 0.5 V →0.2 V

At 45°C;

VHYS-45°C Hysteresis High temp charging to normal CHG; 20 mV

VTS: 0.2 V →0.5 V

bq25100/01/100H/101H/100L;

VTS-60°C High temperature disable High temp charge to pending; 160 170 180 mV

VTS: 0.2 V →0.1 V

At 60°C (bq25100/01/100H/101H/100L);

VHYS-60°C Hysteresis Charge pending to high temp CHG; 20 mV

VTS: 0.1 V →0.2 V

Product Folder Links: bq25100 bq25101 bq25100A bq25100H bq25101H bq25100L

t-time – 10 ms/div

VIN 2 V/div

2 V/div

VOUT

IOUT 60 mA/div

t-time – 20 ms/div

VISET 1 V/div

2 V/div

VOUT

IOUT 60 mA/div

VIN

2 V/div

bq25100

bq25101

bq25100A

bq25100H

bq25101H

bq25100L

SLUSBV8C –AUGUST 2014–REVISED NOVEMBER 2014

www.ti.com

Electrical Characteristics (continued)

Over junction temperature range 0°C ≤TJ≤125°C and recommended supply voltage (unless otherwise noted)

PARAMETER TEST CONDITIONS MIN TYP MAX UNIT

Normal to cold operation; VTS: 0.6 V →1 V 50

tDGL(TS_10C) Deglitch for TS thresholds: 10C ms

Cold to normal operation; VTS: 1 V →0.6 V 12

Deglitch for TS thresholds:

tDGL(TS) Battery charging 30 ms

0/45/60C

Charge enable threshold, (10k

VTS-EN-10k VTS: 0 V →0.175 V 84 92 100 mV

NTC)

HYS below VTS-EN-10k to disable,

VTS-DIS_HYS-10k VTS: 0.125 V →0 V 12 mV

(10k NTC)

THERMAL REGULATION

TJ(REG) Temperature regulation limit 125 °C

TJ(OFF) Thermal shutdown temperature 155 °C

TJ(OFF-HYS) Thermal shutdown hysteresis 20 °C

LOGIC LEVELS ON /CHG

VOL Output low voltage ISINK = 5 mA 0.4 V

ILEAK Leakage current into IC V CHG = 5 V 1 μA

7.6 Typical Characteristics

Setup: Typical Applications Schematic; VIN = 5 V, VBAT = 3.6 V (unless otherwise noted)

No Battery, No Load Hot Plug

Figure 3. Power Up Timing Figure 4. OVP 7-V Adaptor

Product Folder Links: bq25100 bq25101 bq25100A bq25100H bq25101H bq25100L

VISET 1 V/div

VOUT 2 V/div

IOUT 100 mA/div

VIN 5 V/div

t-time – 200 s/divμ

t-time – 20 ms/div

VISET 1 V/div

VOUT 2 V/div

IOUT 100 mA/div

VIN 5 V/div

t-time – 5 ms/div

VISET 1 V/div

VOUT 2 V/div

IOUT 60 mA/div

VIN 1 V/div

t-time – 20 ms/div

VISET 1 V/div

VOUT 2 V/div

IOUT 100 mA/div

VIN 5 V/div

t-time – 50 ms/div

VISET 1 V/div

2 V/div

VOUT

IOUT 60 mA/div

VIN

2 V/div

t-time – 50 ms/div

VISET 1 V/div

VTS 500 mV/div

IOUT 60 mA/div

VIN 2 V/div

bq25100

bq25101

bq25100A

bq25100H

bq25101H

bq25100L

www.ti.com

SLUSBV8C –AUGUST 2014–REVISED NOVEMBER 2014

Typical Characteristics (continued)

Setup: Typical Applications Schematic; VIN = 5 V, VBAT = 3.6 V (unless otherwise noted)

VIN 0 V -5 V-7 V-5 V

Figure 5. OVP from Normal Power-Up Operation Figure 6. TS Enable and Disable

VIN Regulated

Figure 7. DPM-Adaptor Current Limits Figure 8. Hot Plug Source with No Battery - Battery

Detection

No Load

Figure 9. Battery Removal Figure 10. ISET Shorted During Normal Operation

Product Folder Links: bq25100 bq25101 bq25100A bq25100H bq25101H bq25100L

Load Current (mA)

Regulation Voltage (V)

4.19

4.192

4.194

4.196

4.198

4.2

4.202

4.204

4.206

4.208

4.21

1 mA 10 mA 50 mA 100 mA 150 mA 200 mA 250 mA

D001

VREG = 0qC

VREG = 25qC

VREG = 85qC

VREG = 125qC

Input Voltage (V)

Regulation Voltage (V)

4.194

4.195

4.196

4.197

4.198

4.199

4.2

4.201

4.202

4.5 V 5 V 5.5 V 6 V 6.5 V

D002

VREG = 0qC

VREG = 25qC

VREG = 85qC

VREG = 125qC

t-time – 10 ms/div

VISET 2 V/div

ILOAD 70 mA/div

IOUT 70 mA/div

VIN 2 V/div

t-time – 10 ms/div

VISET 1 V/div

VOUT 2 V/div

IOUT 400 mA/div

VIN 2 V/div

t-time – 10 ms/div

VISET 1 V/div

VOUT 5 V/div

IOUT 100 mA/div

VIN 5 V/div

t-time – 10 ms/div

VISET 1 V/div

VOUT 5 V/div

IOUT 100 mA/div

VIN 5 V/div

bq25100

bq25101

bq25100A

bq25100H

bq25101H

bq25100L

SLUSBV8C –AUGUST 2014–REVISED NOVEMBER 2014

www.ti.com

Typical Characteristics (continued)

Setup: Typical Applications Schematic; VIN = 5 V, VBAT = 3.6 V (unless otherwise noted)

20-Ωresistor at OUT, No input, VBAT = 3.7 V

Figure 12. Battery Removal

Figure 11. Battery Plug In

90-mA Load, 120-mA ICHG

Figure 13. ISET Short Prior to Power Up Figure 14. Power Up

Figure 15. Load Regulation Over Temperature Figure 16. Line Regulation Over Temperature

Product Folder Links: bq25100 bq25101 bq25100A bq25100H bq25101H bq25100L

Output Voltage (V)

Output Current (mA)

106

107

108

109

110

111

112

2.5 V 3 V 3.5 V 4 V 4.1 V

D003

IO = 0qC

IO = 25qC

IO = 85qC

IO = 125qC

Output Current (mA)

Output Voltage (V)

0 0

10 0.8

20 1.6

30 2.4

40 3.2

50 4

60 4.8

70 5.6

80 6.4

D004

IOUT (mA)

VOUT (V)

bq25100

bq25101

bq25100A

bq25100H

bq25101H

bq25100L

www.ti.com

SLUSBV8C –AUGUST 2014–REVISED NOVEMBER 2014

Typical Characteristics (continued)

Setup: Typical Applications Schematic; VIN = 5 V, VBAT = 3.6 V (unless otherwise noted)

bq25100 charge cycle, ICHG = 75 mA, VBAT_REG = 4.2 V

Figure 17. Current Regulation Over Temperature Figure 18. Battery Voltage vs Charge Current

Product Folder Links: bq25100 bq25101 bq25100A bq25100H bq25101H bq25100L

bq25100

bq25101

bq25100A

bq25100H

bq25101H

bq25100L

SLUSBV8C –AUGUST 2014–REVISED NOVEMBER 2014

www.ti.com

8 Detailed Description

8.1 Overview

The bq2510x is a highly integrated family of single cell Li-Ion and Li-Pol chargers. The charger can be used to

charge a battery, power a system or both. The charger has three phases of charging: pre-charge to recover a

fully discharged battery, fast-charge constant current to supply the charge safely and voltage regulation to safely

reach full capacity. The charger is very flexible, allowing programming of the fast-charge current and Pre-

charge/Termination Current. This charger is designed to work with a USB connection (100-mA limit) or Adaptor

(DC output). The charger also checks to see if a battery is present.

The charger also comes with a full set of safety features: JEITA Temperature Standard

(bq25100/01/100H/101H), Over-Voltage Protection, DPM-IN, Safety Timers, and ISET short protection. All of

these features and more are described in detail below.

The charger is designed for a single power path from the input to the output to charge a single cell Li-Ion or

Li-Pol battery pack. Upon application of a 5-V DC power source the ISET and OUT short checks are performed

to assure a proper charge cycle.

If the battery voltage is below the LOWV threshold, the battery is considered discharged and a preconditioning

cycle begins. The amount of precharge current can be programmed using the PRE-TERM pin which programs a

percent of fast charge current (10 to 100%) as the precharge current. This feature is useful when the system load

is connected across the battery “stealing” the battery current. The precharge current can be set higher to account

for the system loading while allowing the battery to be properly conditioned. The PRE-TERM pin is a dual

function pin which sets the precharge current level and the termination threshold level. The termination "current

threshold" is always half of the precharge programmed current level.

Once the battery voltage has charged to the VLOWV threshold, fast charge is initiated and the fast charge

current is applied. The fast charge constant current is programmed using the ISET pin. The constant current

provides the bulk of the charge. Power dissipation in the IC is greatest in fast charge with a lower battery voltage.

If the IC reaches 125°C, the IC enters thermal regulation, slows the timer clock by half, and reduces the charge

current as needed to keep the temperature from rising any further. Figure 19 shows the charging profile with

thermal regulation. Typically under normal operating conditions, the IC’s junction temperature is less than 125°C

and thermal regulation is not entered.

Once the cell has charged to the regulation voltage the voltage loop takes control and holds the battery at the

regulation voltage until the current tapers to the termination threshold. The termination can be disabled if desired.

Further details are described in the Operating Modes section.

Product Folder Links: bq25100 bq25101 bq25100A bq25100H bq25101H bq25100L

PRE-CHARGE

CURRENT AND

TERMINATION

THRESHOLD

FAST-CHARGE

CURRENT

T(PRECHG)

Charge

Complete

Status,

Charger

Off

Pre-

Conditioning

Phase

Current

Regulation

Phase

VoltageRegulationand

ChargeTermination

Phase

Battery

Voltage,

V(OUT)

BatteryCurrent,

I(OUT)

DONE

Thermal

Regulation

Phase

Temperature, Tj

IO(OUT)

T(THREG)

I(TERM)

IO(PRECHG)

VO(REG)

VO(LOWV)

DONE

T(CHG)

bq25100

bq25101

bq25100A

bq25100H

bq25101H

bq25100L

www.ti.com

SLUSBV8C –AUGUST 2014–REVISED NOVEMBER 2014

Overview (continued)

Figure 19. Charging Profile With Thermal Regulation

Product Folder Links: bq25100 bq25101 bq25100A bq25100H bq25101H bq25100L

-80 mV

OUT

Charge

Pump

Input

Power

Detect IN

IN-DPMREF

OUT

OUTREGREF

OVPREF

125ÛCREF

ISET

Charge

Pump

PRE-TERM

PA

CHARGE

CONTROL

OUT

VTERM_EN

VCOLD-0ÛC

VHOT-60ÛC

VLDO

VDISABLE

5PA 45PA

VCLAMP=1.4V

Cold Temperature Sink

Current

= 45PA

LO=LDO MODE

HI=CHIP DISABLE

OUT

Internal Charge

Current Sense

w/ Multiple Outputs

Internal Current

Sensing Resistor

22mA Startup Current

Limit

1.5V

FAST CHARGE

PRE-CHARGE

PRE-CHG Reference

Term Reference

150ÛCREF

Thermal Shutdown

VWARM-45ÛC

VCOOL-10ÛC

Disable Sink

Current = 20PA

bq25100

bq25101

bq25100A

bq25100H

bq25101H

bq25100L

SLUSBV8C –AUGUST 2014–REVISED NOVEMBER 2014

www.ti.com

8.2 Functional Block Diagram

Product Folder Links: bq25100 bq25101 bq25100A bq25100H bq25101H bq25100L

bq25100

bq25101

bq25100A

bq25100H

bq25101H

bq25100L

www.ti.com

SLUSBV8C –AUGUST 2014–REVISED NOVEMBER 2014

8.3 Feature Description

8.3.1 Overvoltage-Protection (OVP) – Continuously Monitored

If the input source applies an overvoltage, the pass FET, if previously on, turns off after a deglitch, tBLK(OVP). The

timer stops counting. Once the overvoltage returns to a normal voltage, the timer and charge continues.

8.3.2 CHG Pin Indication (bq25101, bq25101H)

The charge pin has an internal open drain FET which is on (pulls down to VSS) during the first charge only

(independent of TTDM) and is turned off once the battery reaches voltage regulation and the charge current

tapers to the termination threshold set by the PRE-TERM resistor. The bq25101/01H terminates at 10% of the

programmed charge current. The charge pin is high impedance in sleep mode and OVP and returns to its

previous state once the condition is removed. Cycling input power, removing and replacing the battery, pulling

the TS pin low and releasing or entering pre-charge mode causes the CHG pin to go reset (go low if power is

good and a discharged battery is attached) and is considered the start of a first charge.

8.3.3 CHG Pin LED Pull-up Source (bq25101, bq25101H)

For host monitoring, a pull-up resistor is used between the CHG pin and the VCC of the host and for a visual

indication a resistor in series with an LED is connected between the /CHG pin and a power source. If the CHG

source is capable of exceeding 7 V, a 6.2-V zener should be used to clamp the voltage. If the source is the OUT

pin, note that as the battery changes voltage, and the brightness of the LEDs vary.

8.3.4 IN-DPM (VIN-DPM or IN-DPM)

The IN-DPM feature is used to detect an input source voltage that is folding back (voltage dropping), reaching its

current limit due to excessive load. When the input voltage drops to the VIN-DPM threshold the internal pass FET

starts to reduce the current until there is no further drop in voltage at the input. This would prevent a source with

voltage less than VIN-DPM to power the out pin. This is an added safety feature that helps protect the source from

excessive loads. This feature is not applicable for bq25100A.

8.3.5 OUT

The Charger’s OUT pin provides current to the battery and to the system, if present. This IC can be used to

charge the battery plus power the system, charge just the battery or just power the system (TTDM) assuming the

loads do not exceed the available current. The OUT pin is a current limited source and is inherently protected

against shorts. If the system load ever exceeds the output programmed current threshold, the output will be

discharged unless there is sufficient capacitance or a charged battery present to supplement the excessive load.

8.3.6 ISET

An external resistor is used to Program the Output Current (10 to 250 mA) and can be used as a current monitor.

RISET = KISET ÷ IOUT (1)

Where:

IOUT is the desired fast charge current;

KISET is a gain factor found in the electrical specification

For greater accuracy at lower currents, part of the sense FET is disabled to give better resolution. Going from

higher currents to low currents, there is hysteresis and the transition occurs around 50 mA.

The ISET resistor is short protected and will detect a resistance lower than ≉420 Ω. The detection requires at

least 50 mA of output current. If a “short” is detected, then the IC will latch off and can be reset by cycling the

power or cycling TS pin. The OUT current is internally clamped to a maximum current of 600 mA typical and is

independent of the ISET short detection circuitry.

For charge current that is below 50 mA, an extra RC circuit is recommended on ISET to acheive more stable

current signal. More detail is available in 9.1 Application Information.

Product Folder Links: bq25100 bq25101 bq25100A bq25100H bq25101H bq25100L

VCOLD

VCOOLVHOT

Programmed ICHG

(100%)

Programmed VBAT_REG

50%

Termination

Disable

VWARM

0.20 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8

Cold Fault

No Operation

During Cold Fault

Reduced VBAT_REG

TS Voltage-V

60C 45C 10C 0C

bq25100

bq25101

bq25100A

bq25100H

bq25101H

bq25100L

SLUSBV8C –AUGUST 2014–REVISED NOVEMBER 2014

www.ti.com

Feature Description (continued)

Figure 20. Operation Over TS Bias Voltage - bq25100, bq25100H, bq25101, bq25101H

Product Folder Links: bq25100 bq25101 bq25100A bq25100H bq25101H bq25100L

VCOLD

VCOOLVHOT

Programmed ICHG

(100%)

Programmed VBAT_REG

50%

Termination

Disable

VWARM

0.20 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8

Cold Fault

No Operation

During Cold Fault

Hot Fault

Charge Disable

TS Voltage-V

45C 10C 0C

bq25100

bq25101

bq25100A

bq25100H

bq25101H

bq25100L

www.ti.com

SLUSBV8C –AUGUST 2014–REVISED NOVEMBER 2014

Feature Description (continued)

Figure 21. Operation Over TS Bias Voltage – bq25100A

8.3.7 PRE_TERM – Pre-Charge and Termination Programmable Threshold

Pre-Term is used to program both the pre-charge current and the termination current threshold. The pre-charge

current level is a factor of two higher than the termination current level. The termination can be set between 5

and 50% (recommended range) of the programmed output current level set by ISET. If left floating the

termination and pre-charge are set internally at 10/20% respectively. The RPRE-TERM is ranged from 600 Ωto 30

kΩand the minimum termination current can be programmed to 1 mA. The pre-charge-to-fast-charge, Vlowv

threshold is set to 2.5 V.

RPRE-TERM = %Term × KTERM = %Pre-CHG × KPRE-CHG (2)

Where:

%Term is the percent of fast charge current where termination occurs;

%Pre-CHG is the percent of fast charge current that is desired during precharge;

KTERM and KPRE-CHG are gain factors found in the electrical specifications.

8.3.8 TS

The TS function for the bq2510x family is designed to follow the new JEITA temperature standard

(bq25100/bq25100H/bq25101/bq25101H) for Li-Ion and Li-Pol batteries. There are now four thresholds, 60°C,

45°C, 10°C, and 0°C. Normal operation occurs between 10°C and 45°C. If between 0°C and 10°C the charge

current level is cut in half and if between 45°C and 60°C the regulation voltage is reduced to 4.1 V max for

bq25100 and 4.2 V max for bq25100H, see Figure 20. The TS function for the bq25100A cut the charge current

level in half between 0°C and 10°C and disables charging when the NTC temperature is above 45°C.

Product Folder Links: bq25100 bq25101 bq25100A bq25100H bq25101H bq25100L

bq25100

bq25101

bq25100A

bq25100H

bq25101H

bq25100L

SLUSBV8C –AUGUST 2014–REVISED NOVEMBER 2014

www.ti.com

Feature Description (continued)

The TS feature is implemented using an internal 50μA current source to bias the thermistor (designed for use

with a 10-k NTC β= 3370 (SEMITEC 103AT-2 or Mitsubishi TH05-3H103F) connected from the TS pin to VSS. If

this feature is not needed, a fixed 10-k can be placed between TS and VSS to allow normal operation. This may

be done if the host is monitoring the thermistor and then the host would determine when to pull the TS pin low to

disable charge.

The TS pin has two additional features, when the TS pin is pulled low or floated/driven high. A low disables

charge and a high puts the charger in TTDM.

Above 60°C (45°C for bq25100A) or below 0°C the charge is disabled. Once the thermistor reaches ≉–10°C the

TS current folds back to keep a cold thermistor (between –10°C and –50°C) from placing the IC in the TTDM

mode. If the TS pin is pulled low into disable mode, the current is reduce to ≉30 μA. Since the ITS curent is fixed

along with the temperature thresholds, it is not possible to use thermistor values other than the 10-k NTC (at

25°C).

8.3.9 Timers

The pre-charge timer is set to 30 minutes. The pre-charge current, can be programmed to off-set any system

load, making sure that the 30 minutes is adequate.

The fast charge timer is fixed at 10 hours and can be increased real time by going into thermal regulation or IN-

DPM. The timer clock slows by a factor of 2, resulting in a clock than counts half as fast when in these modes. If

either the 30 minute or ten hour timer times out, the charging is terminated and for bq25101/1H the CHG pin

goes high impedance if not already in that state. The timer is reset by disabling the IC, cycling power or going

into and out of TTDM.

8.3.10 Termination

Once the OUT pin goes above VRCH, (reaches voltage regulation) and the current tapers down to the

termination threshold, a battery detect route is run to determine if the battery was removed or the battery is full. If

the battery is present, the charge current will terminate. If the battery was removed along with the thermistor,

then the TS pin is driven high and the charge enters TTDM. If the battery was removed and the TS pin is held in

the active region, then the battery detect routine will continue until a battery is inserted. The termination current

can be programmed down to 625 uA, however, the accuracy will reduce acoordingly when the termination

current is below 1 mA.

8.4 Device Functional Modes

8.4.1 Power-Down or Undervoltage Lockout (UVLO)

The bq2510x family is in power down mode if the IN pin voltage is less than UVLO. The part is considered

“dead” and all the pins are high impedance. Once the IN voltage rises above the UVLO threshold the IC will

enter Sleep Mode or Active mode depending on the OUT pin (battery) voltage.

8.4.2 Power-up

The IC is alive after the IN voltage ramps above UVLO (see sleep mode), resets all logic and timers, and starts

to perform many of the continuous monitoring routines. Typically the input voltage quickly rises through the

UVLO and sleep states where the IC declares power good, starts the qualification charge at 22 mA, sets the

charge current base on the ISET pin, and starts the safety timer.

8.4.3 Sleep Mode

If the IN pin voltage is between VOUT+VDT and UVLO, the charge current is disabled, the safety timer counting

stops (not reset). As the input voltage rises and the charger exits sleep mode, the safety timer continues to count

and the charge is enabled. See Figure 22.

8.4.4 New Charge Cycle

A new charge cycle is started when a good power source is applied, performing a chip disable/enable (TS pin),

exiting Termination and Timer Disable Mode (TTDM), detecting a battery insertion or the OUT voltage dropping

below the VRCH threshold.

Product Folder Links: bq25100 bq25101 bq25100A bq25100H bq25101H bq25100L

Is power good?

VBAT+VDT<VIN<VOVP

&VUVLO<VIN

Apply Input

Power

Is chip enabled?

VTS>VEN

Set Input Current Limit to 22mA

And Start Charge

Perform ISET & OUT short tests

Return to

Charge

Set charge current

based on ISET setting

Yes

bq25100

bq25101

bq25100A

bq25100H

bq25101H

bq25100L

www.ti.com

SLUSBV8C –AUGUST 2014–REVISED NOVEMBER 2014

Device Functional Modes (continued)

Figure 22. bq2510x Power-Up Flow Diagram

Product Folder Links: bq25100 bq25101 bq25100A bq25100H bq25101H bq25100L

bq25100

bq25101

bq25100A

bq25100H

bq25101H

bq25100L

SLUSBV8C –AUGUST 2014–REVISED NOVEMBER 2014

www.ti.com

Device Functional Modes (continued)

8.4.5 Termination and Timer Disable Mode (TTDM) - TS Pin High

The battery charger is in TTDM when the TS pin goes high from removing the thermistor (removing battery

pack/floating the TS pin) or by pulling the TS pin up to the TTDM threshold.

When entering TTDM, the 10 hour safety timer is held in reset and termination is disabled. A battery detect

routine is run to see if the battery was removed or not. For bq25101/1H, if the battery was removed then the

CHG pin will go to its high impedance state if not already there. If a battery is detected the CHG pin does not

change states until the current tapers to the termination threshold, where the CHG pin goes to its high

impedance state if not already there (the regulated output will remain on).

The charging profile does not change (still has pre-charge, fast-charge constant current and constant voltage

modes). This implies the battery is still charged safely and the current is allowed to taper to zero.

When coming out of TTDM, the battery detect routine is run and if a battery is detected, then a new charge cycle

begins.

If TTDM is not desired upon removing the battery with the thermistor, one can add a 237-kΩresistor between TS

and VSS to disable TTDM. This keeps the current source from driving the TS pin into TTDM. This creates ≉0.1°C

error at hot and a ≉3°C error at cold.

8.4.6 Battery Detect Routine

The battery detect routine should check for a missing battery while keeping the OUT pin at a useable voltage.

The battery detect routine is run when entering and exiting TTDM to verify if battery is present, or run all the time

if battery is missing and not in TTDM. On power-up, if battery voltage is greater than VRCH thereshold, a battery

detect routine is run to determine if a battery is present.

The battery detect routine is disabled while the IC is in TTDM, or has a TS fault. See Figure 23 for the Battery

Detect Flow Diagram.

8.4.7 Refresh Threshold

After termination, if the OUT pin voltage drops to VRCH (100mV below regulation) then a new charge is initiated.

8.4.8 Starting a Charge on a Full Battery

The termination threshold is raised by ≉14% for the first minute of a charge cycle so if a full battery is removed

and reinserted or a new charge cycle is initiated, that the new charge terminates (less than 1 minute). Batteries

that have relaxed many hours may take several minutes to taper to the termination threshold and terminate

charge.

Product Folder Links: bq25100 bq25101 bq25100A bq25100H bq25101H bq25100L

Start

BATT_DETECT

Start 25mstimer

TimerExpired?

IsVOUT<VREG-100mV?

BatteryPresent

TurnoffSinkCurrent

Returntoflow

SetOUT REG

toVREG-400mV

Enablesinkcurrent

Reset & Start 25mstimer

Yes

TimerExpired? No

Yes

IsVOUT>VREG-300mV?

BatteryPresent

TurnoffSinkCurrent

Returntoflow

Yes

Battery Absent

Don’tSignalCharge

TurnoffSinkCurrent

ReturntoFlow

bq25100

bq25101

bq25100A

bq25100H

bq25101H

bq25100L

www.ti.com

SLUSBV8C –AUGUST 2014–REVISED NOVEMBER 2014

Device Functional Modes (continued)

Figure 23. Battery Detect Routine

Product Folder Links: bq25100 bq25101 bq25100A bq25100H bq25101H bq25100L

VBUS

GND

HOST

bq25100

OUT

1ÛF1ÛF

SYSTEM

D+

D-

USB Port or

Adapter

ISET

PRETERM

TEMP PACK+

PACK-

VSS

3.4k

6k

2.7k

10 nF

Optional

bq25100

bq25101

bq25100A

bq25100H

bq25101H

bq25100L

SLUSBV8C –AUGUST 2014–REVISED NOVEMBER 2014

www.ti.com

9 Application and Implementation

NOTE

Information in the following applications sections is not part of the TI component

specification, and TI does not warrant its accuracy or completeness. TI’s customers are

responsible for determining suitability of components for their purposes. Customers should

validate and test their design implementation to confirm system functionality.

9.1 Application Information

The bq2510x series of devices are highly integrated Li-Ion and Li-Pol linear chargers targeted at space-limited

portable applications. The fast charge current can be programmed from 10 mA to 250 mA through an external

resistor on ISET pin. The pre_charge and termination current can also be programmed through the resistor

connected on PRETERM pin. The device has complete system-level protection such as input under-voltage

lockout (UVLO), input over-voltage protection (OVP), sleep mode, thermal regulation, safety timers, and NTC

monitoring input.

9.2 Typical Application - Charger Application Design Example

9.2.1 Design Requirements

• Supply voltage = 5 V

• Fast charge current: IOUT-FC = 40 mA;

• Termination Current Threshold: %IOUT-FC = 10% of Fast Charge or ~4 mA

• Pre-Charge Current by default is twice the termination Current or ~8 mA

• TS – Battery Temperature Sense = 10-k NTC (103AT)

• /CE is an open drain control pin

9.2.2 Detailed Design Procedures

• The regulation voltage is set to 4.2 V, the input voltage is 5 V and the charge current is programmed to 40

mA.

• For charge current that is below 50 mA, an extra RC circuit is recommended on ISET to acheive more stable

current signal. For applications that need higher charge current, the RC circuit is not needed.

• For applications that use more than 200-mA current, there could be a very low level ~1% of charge current

ringing in the output. The ringing can be removed by increasing the input capacitance.

Product Folder Links: bq25100 bq25101 bq25100A bq25100H bq25101H bq25100L

t-time – 50 ms/div

VISET 1 V/div

2 V/div

VOUT

IOUT 60 mA/div

VIN

2 V/div

t-time – 20 ms/div

VISET 1 V/div

2 V/div

VOUT

IOUT 60 mA/div

VIN

2 V/div

bq25100

bq25101

bq25100A

bq25100H

bq25101H

bq25100L

www.ti.com

SLUSBV8C –AUGUST 2014–REVISED NOVEMBER 2014

Typical Application - Charger Application Design Example (continued)

9.2.2.1 Calculations

9.2.2.1.1 Program the Fast Charge Current, ISET:

RISET = [K(ISET) / I(OUT)]

from electrical characteristics table. . . K(SET) = 135 AΩ

RISET = [135 AΩ/0.04 A] = 3.4 kΩ

Selecting the closest standard value, use a 3.4-kΩresistor between ISET and Vss.

9.2.2.1.2 Program the Termination Current Threshold, ITERM:

RPRE-TERM = K(TERM) × %IOUT-FC

RPRE-TERM = 600 Ω/% × 10% = 6 kΩ

Selecting the closest standard value, use a 6-kΩresistor between PRETERM and Vss.

One can arrive at the same value by using 20% for a pre-charge value (factor of 2 difference).

RPRE-TERM = K(PRE-CHG) × %IOUT-FC

RPRE-TERM = 300 Ω/% × 20%= 6 kΩ

9.2.2.1.3 TS Function

Use a 10-k NTC thermistor in the battery pack (103AT).

To Disable the temp sense function, use a fixed 10-kΩresistor between the TS and VSS.

9.2.2.1.4 Selecting IN and OUT Pin Capacitors

In most applications, all that is needed is a high-frequency decoupling capacitor (ceramic) on the power pin, input

and output pins. Using the values shown on the application diagram is recommended. After evaluation of these

voltage signals with real system operational conditions, one can determine if capacitance values can be adjusted

toward the minimum recommended values (DC load application) or higher values for fast, high amplitude, pulsed

load applications. Note if designed for high input voltage sources (bad adaptors or wrong adaptors), the capacitor

needs to be rated appropriately. Ceramic capacitors are tested to 2x their rated values so a 16-V capacitor may

be adequate for a 30-V transient (verify tested rating with capacitor manufacturer).

9.2.3 bq25100 Application Performance Plots

Hot Plug VIN 0 V -5 V-7 V-5 V

Figure 24. OVP 7-V Adaptor Figure 25. OVP from Normal Power-Up Operation

Product Folder Links: bq25100 bq25101 bq25100A bq25100H bq25101H bq25100L

t-time – 50 ms/div

VISET 1 V/div

VTS 500 mV/div

IOUT 60 mA/div

VIN 2 V/div

t-time – 10 ms/div

VISET 2 V/div

ILOAD 70 mA/div

IOUT 70 mA/div

VIN 2 V/div

bq25100

bq25101

bq25100A

bq25100H

bq25101H

bq25100L

SLUSBV8C –AUGUST 2014–REVISED NOVEMBER 2014

www.ti.com

Typical Application - Charger Application Design Example (continued)

90-mA Load, 120-mA IOUT

Figure 26. TS Enable and Disable Figure 27. Power Up

10 Power Supply Recommendations

10.1 Leakage Current Effects on Battery Capacity

To determine how fast a leakage current on the battery will discharge the battery is an easy calculation. The time

from full to discharge can be calculated by dividing the Amp-Hour Capacity of the battery by the leakage current.

For a 0.1-AHr battery and a 75-nA leakage current (100mAHr/75nA = 250000 Hours), it would take 1333k hours

or 152 years to discharge. In reality the self discharge of the cell would be much faster so the 75-nA leakage

would be considered negligible.

11 Layout

11.1 Layout Guidelines

To obtain optimal performance, the decoupling capacitor from IN to GND and the output filter capacitors from

OUT to GND should be placed as close as possible to the bq2510x, with short trace runs to both IN, OUT and

GND.

• All low-current GND connections should be kept separate from the high-current charge or discharge paths

from the battery. Use a single-point ground technique incorporating both the small signal ground path and the

power ground path.

• The high current charge paths into IN pin and from the OUT pin must be sized appropriately for the maximum

charge current in order to avoid voltage drops in these traces

Product Folder Links: bq25100 bq25101 bq25100A bq25100H bq25101H bq25100L

bq25100

bq25101

bq25100A

bq25100H

bq25101H

bq25100L

www.ti.com

SLUSBV8C –AUGUST 2014–REVISED NOVEMBER 2014

11.2 Layout Example

Figure 28. Board Layout

11.3 Thermal Package

The most common measure of package thermal performance is thermal impedance (θJA ) measured (or

modeled) from the chip junction to the air surrounding the package surface (ambient). The mathematical

expression for θJA is:

θJA = (TJ– T) / P (3)

Where:

TJ= chip junction temperature

T = ambient temperature

P = device power dissipation

Factors that can influence the measurement and calculation of θJA include:

1. Whether or not the device is board mounted

2. Trace size, composition, thickness, and geometry

3. Orientation of the device (horizontal or vertical)

4. Volume of the ambient air surrounding the device under test and airflow

5. Whether other surfaces are in close proximity to the device being tested

Due to the charge profile of Li-Ion and Li-Pol batteries the maximum power dissipation is typically seen at the

beginning of the charge cycle when the battery voltage is at its lowest. Typically after fast charge begins the pack

voltage increases to ≉3.4 V within the first 2 minutes. The thermal time constant of the assembly typically takes a

few minutes to heat up so when doing maximum power dissipation calculations, 3.4 V is a good minimum voltage

to use.

The device power dissipation, P, is a function of the charge rate and the voltage drop across the internal

PowerFET. It can be calculated from the following equation when a battery pack is being charged :

P = [V(IN) – V(OUT)] × I(OUT) (4)

Product Folder Links: bq25100 bq25101 bq25100A bq25100H bq25101H bq25100L

bq25100

bq25101

bq25100A

bq25100H

bq25101H

bq25100L

SLUSBV8C –AUGUST 2014–REVISED NOVEMBER 2014

www.ti.com

Thermal Package (continued)

The thermal loop feature reduces the charge current to limit excessive IC junction temperature. It is

recommended that the design not run in thermal regulation for typical operating conditions (nominal input voltage

and nominal ambient temperatures) and use the feature for non typical situations such as hot environments or

higher than normal input source voltage. With that said, the IC will still perform as described, if the thermal loop

is always active.

12 Device and Documentation Support

12.1 Device Support

12.1.1 Third-Party Products Disclaimer

TI'S PUBLICATION OF INFORMATION REGARDING THIRD-PARTY PRODUCTS OR SERVICES DOES NOT

CONSTITUTE AN ENDORSEMENT REGARDING THE SUITABILITY OF SUCH PRODUCTS OR SERVICES

OR A WARRANTY, REPRESENTATION OR ENDORSEMENT OF SUCH PRODUCTS OR SERVICES, EITHER

ALONE OR IN COMBINATION WITH ANY TI PRODUCT OR SERVICE.

12.2 Related Links

The table below lists quick access links. Categories include technical documents, support and community

resources, tools and software, and quick access to sample or buy.

Table 1. Related Links

TECHNICAL TOOLS & SUPPORT &

PARTS PRODUCT FOLDER SAMPLE & BUY DOCUMENTS SOFTWARE COMMUNITY

bq25100 Click here Click here Click here Click here Click here

bq25101 Click here Click here Click here Click here Click here

bq25100A Click here Click here Click here Click here Click here

bq25100H Click here Click here Click here Click here Click here

bq25101H Click here Click here Click here Click here Click here

bq25100L Click here Click here Click here Click here Click here

12.3 Trademarks

Bluetooth is a registered trademark of Bluetooth SIG, Inc..

12.4 Electrostatic Discharge Caution

These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam

during storage or handling to prevent electrostatic damage to the MOS gates.

12.5 Glossary

SLYZ022 —TI Glossary.

This glossary lists and explains terms, acronyms, and definitions.

13 Mechanical, Packaging, and Orderable Information

The following pages include mechanical, packaging, and orderable information. This information is the most

current data available for the designated devices. This data is subject to change without notice and revision of

this document. For browser-based versions of this data sheet, refer to the left-hand navigation.

Product Folder Links: bq25100 bq25101 bq25100A bq25100H bq25101H bq25100L

PACKAGE OPTION ADDENDUM

www.ti.com 15-Jun-2015

Addendum-Page 1

PACKAGING INFORMATION

Orderable Device Status

(1)

Package Type Package

Drawing Pins Package

Qty Eco Plan

(2)

Lead/Ball Finish

(6)

MSL Peak Temp

(3)

Op Temp (°C) Device Marking

(4/5)

Samples

BQ25100AYFPR ACTIVE DSBGA YFP 6 3000 Green (RoHS

& no Sb/Br) SNAGCU Level-1-260C-UNLIM -40 to 85 25100A

BQ25100AYFPT ACTIVE DSBGA YFP 6 250 Green (RoHS

& no Sb/Br) SNAGCU Level-1-260C-UNLIM -40 to 85 25100A

BQ25100HYFPR ACTIVE DSBGA YFP 6 3000 Green (RoHS

& no Sb/Br) SNAGCU Level-1-260C-UNLIM 0 to 125 25100H

BQ25100HYFPT ACTIVE DSBGA YFP 6 250 Green (RoHS

& no Sb/Br) SNAGCU Level-1-260C-UNLIM 0 to 125 25100H

BQ25100YFPR ACTIVE DSBGA YFP 6 3000 Green (RoHS

& no Sb/Br) SNAGCU Level-1-260C-UNLIM 0 to 125 25100

BQ25100YFPT ACTIVE DSBGA YFP 6 250 Green (RoHS

& no Sb/Br) SNAGCU Level-1-260C-UNLIM 0 to 125 25100

BQ25101HYFPR ACTIVE DSBGA YFP 6 3000 Green (RoHS

& no Sb/Br) SNAGCU Level-1-260C-UNLIM 0 to 125 25101H

BQ25101HYFPT ACTIVE DSBGA YFP 6 250 Green (RoHS

& no Sb/Br) SNAGCU Level-1-260C-UNLIM 0 to 125 25101H

BQ25101YFPR ACTIVE DSBGA YFP 6 3000 Green (RoHS

& no Sb/Br) SNAGCU Level-1-260C-UNLIM 0 to 125 25101

BQ25101YFPT ACTIVE DSBGA YFP 6 250 Green (RoHS

& no Sb/Br) SNAGCU Level-1-260C-UNLIM 0 to 125 25101

(1) The marketing status values are defined as follows:

ACTIVE: Product device recommended for new designs.

LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.

NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.

PREVIEW: Device has been announced but is not in production. Samples may or may not be available.

OBSOLETE: TI has discontinued the production of the device.

(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability

information and additional product content details.

TBD: The Pb-Free/Green conversion plan has not been defined.

Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that

lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.

Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between

the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.

Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight

in homogeneous material)

PACKAGE OPTION ADDENDUM

www.ti.com 15-Jun-2015

Addendum-Page 2

(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.

(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.

(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation

of the previous line and the two combined represent the entire Device Marking for that device.

(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish

value exceeds the maximum column width.

Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information

provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and

continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.

TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.

In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.

TAPE AND REEL INFORMATION

*All dimensions are nominal

Device Package

Type Package

Drawing Pins SPQ Reel

Diameter

(mm)

Reel

Width

W1 (mm)

(mm) B0

(mm) K0

(mm) P1

(mm) W

(mm) Pin1

Quadrant

BQ25100AYFPR DSBGA YFP 6 3000 180.0 8.4 0.98 1.68 0.59 4.0 8.0 Q1

BQ25100AYFPT DSBGA YFP 6 250 180.0 8.4 0.98 1.68 0.59 4.0 8.0 Q1

BQ25100HYFPR DSBGA YFP 6 3000 180.0 8.4 0.98 1.68 0.59 4.0 8.0 Q1

BQ25100HYFPT DSBGA YFP 6 250 180.0 8.4 0.98 1.68 0.59 4.0 8.0 Q1

BQ25100YFPR DSBGA YFP 6 3000 180.0 8.4 0.98 1.68 0.59 4.0 8.0 Q1

BQ25100YFPT DSBGA YFP 6 250 180.0 8.4 0.98 1.68 0.59 4.0 8.0 Q1

BQ25101HYFPR DSBGA YFP 6 3000 180.0 8.4 0.98 1.68 0.59 4.0 8.0 Q1

BQ25101HYFPT DSBGA YFP 6 250 180.0 8.4 0.98 1.68 0.59 4.0 8.0 Q1

BQ25101YFPR DSBGA YFP 6 3000 180.0 8.4 0.98 1.68 0.59 4.0 8.0 Q1

BQ25101YFPT DSBGA YFP 6 250 180.0 8.4 0.98 1.68 0.59 4.0 8.0 Q1

PACKAGE MATERIALS INFORMATION

www.ti.com 8-Apr-2016

Pack Materials-Page 1

*All dimensions are nominal

Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)

BQ25100AYFPR DSBGA YFP 6 3000 182.0 182.0 20.0

BQ25100AYFPT DSBGA YFP 6 250 182.0 182.0 20.0

BQ25100HYFPR DSBGA YFP 6 3000 182.0 182.0 20.0

BQ25100HYFPT DSBGA YFP 6 250 182.0 182.0 20.0

BQ25100YFPR DSBGA YFP 6 3000 210.0 185.0 35.0

BQ25100YFPT DSBGA YFP 6 250 210.0 185.0 35.0

BQ25101HYFPR DSBGA YFP 6 3000 182.0 182.0 20.0

BQ25101HYFPT DSBGA YFP 6 250 182.0 182.0 20.0

BQ25101YFPR DSBGA YFP 6 3000 182.0 182.0 20.0

BQ25101YFPT DSBGA YFP 6 250 182.0 182.0 20.0

PACKAGE MATERIALS INFORMATION

www.ti.com 8-Apr-2016

Pack Materials-Page 2

www.ti.com

PACKAGE OUTLINE

0.5 MAX

0.19

0.13

0.8

TYP

0.4

TYP

0.4 TYP

6X 0.25

0.21

B E A

4223410/A 11/2016

DSBGA - 0.5 mm max heightYFP0006

DIE SIZE BALL GRID ARRAY

NOTES:

1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing

per ASME Y14.5M.

2. This drawing is subject to change without notice.

BALL A1

CORNER

SEATING PLANE

BALL TYP 0.05 C

0.015 C A B

SYMM

SCALE 10.000

D: Max =

E: Max =

1.608 mm, Min =

0.91 mm, Min =

1.547 mm

0.85 mm

www.ti.com

EXAMPLE BOARD LAYOUT

6X ( 0.23)

(0.4) TYP

( 0.23)

METAL 0.05 MAX

SOLDER MASK

OPENING

METAL UNDER

SOLDER MASK

( 0.23)

SOLDER MASK

OPENING

0.05 MIN

4223410/A 11/2016

DSBGA - 0.5 mm max heightYFP0006

DIE SIZE BALL GRID ARRAY

NOTES: (continued)

3. Final dimensions may vary due to manufacturing tolerance considerations and also routing constraints.

For more information, see Texas Instruments literature number SNVA009 (www.ti.com/lit/snva009).

SOLDER MASK DETAILS

NOT TO SCALE

SYMM

LAND PATTERN EXAMPLE

SCALE:50X

NON-SOLDER MASK

DEFINED

(PREFERRED)

SOLDER MASK

DEFINED

www.ti.com

EXAMPLE STENCIL DESIGN

(0.4) TYP

6X ( 0.25) (R0.05) TYP

METAL

TYP

4223410/A 11/2016

DSBGA - 0.5 mm max heightYFP0006

DIE SIZE BALL GRID ARRAY

NOTES: (continued)

4. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release.

SYMM

SOLDER PASTE EXAMPLE

BASED ON 0.1 mm THICK STENCIL

SCALE:50X

IMPORTANT NOTICE

Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its

semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers

should obtain the latest relevant information before placing orders and should verify that such information is current and complete.

TI’s published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated

circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and

services.

Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is

accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced

documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements

different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the

associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.

Buyers and others who are developing systems that incorporate TI products (collectively, “Designers”) understand and agree that Designers

remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have

full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products

used in or for Designers’ applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with

respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous

consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and

take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will

thoroughly test such applications and the functionality of such TI products as used in such applications.

TI’s provision of technical, application or other design advice, quality characterization, reliability data or other services or information,

including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to

assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any

way, Designer (individually or, if Designer is acting on behalf of a company, Designer’s company) agrees to use any particular TI Resource

solely for this purpose and subject to the terms of this Notice.

TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI

products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,

enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically

described in the published documentation for a particular TI Resource.

Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that

include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE

TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY

RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or

other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information

regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or

endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the

third party, or a license from TI under the patents or other intellectual property of TI.

TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR

REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO

ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF

MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL

PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM,

INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF

PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL,

DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN

CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN

ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949

and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements.

Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such

products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards

and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must

ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in

life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use.

Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life

support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all

medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S.

TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product).

Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications

and that proper product selection is at Designers’ own risk. Designers are solely responsible for compliance with all legal and regulatory

requirements in connection with such selection.

Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer’s non-

compliance with the terms and provisions of this Notice.

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Texas Instruments:

BQ25101HYFPR BQ25101HYFPT