AOZ1283 EZBuckTM 2.5A Simple Buck Regulator General Description Features The AOZ1283 is a high voltage, high efficiency, simple to use, 2.5A buck regulator optimized for a variety of applications. The AOZ1283 works from a 3.0V to 36V input voltage range, and provides up to 2.5A of continuous output current. The output voltage is adjustable from 30V down to 0.8V. 3.0V to 36V operating input voltage range The AOZ1283 integrates an N-channel high-side power MOSFET. The switching frequency can set from 200kHz to 2MHz with an external resistor. The soft-start time can be set with an external capacitor. 50m internal NMOS Up to 95% efficiency Adjustable soft-start Output voltage adjustable from 0.8V to 30V 2.5A continuous output current Adjustable switching frequency from 200kHz to 2MHz Cycle-by-cycle current limit Short-circuit protection Over-voltage protection Over-temperature protection EPAD SO-8 package Applications Point-of-load DC/DC conversion Set top boxes and cable modems DVD drives and HDDs LCD Monitors & TVs Telecom/Networking/Datacom equipment Typical Application VIN up to 36V CSS CIN VIN BS SS L1 FSW RF LX R1 AOZ1283 EN VOUT 22H CO FB COMP GND R2 CC RC Figure 1. 36V/2.5A Buck Regulator Rev. 1.0 May 2014 www.aosmd.com Page 1 of 15 AOZ1283 Ordering Information Part Number Ambient Temperature Range Package Environmental AOZ1283PI -40 C to +85 C EPAD SO-8 Green Product AOS Green Products use reduced levels of Halogens, and are also RoHS compliant. Please visit www.aosmd.com/media/AOSGreenPolicy.pdf for additional information. Pin Configuration LX 1 BST 2 GND 3 FSW 4 8 EN Exposed PAD 7 SS VIN 6 FB 5 COMP Pin Description Pin Number Pin Name Pin Function 1 LX 2 BST Bootstrap Voltage Input. Driver supply for High-side NMOS. Connected to 100nF capacitor between BST and LX. PWM Output. Connect to inductor. 3 GND Ground. 4 FSW Frequency Bias. Connect to resistor to determine switching frequency. 5 COMP 6 FB Compensation. Connect to resistor and capacitor for system stability. Feedback Input. It is regulated to 0.8V. The FB pin is used to determine the PWM output voltage via a resistor divider between the output and GND. 7 SS Soft Start. 8 EN Enable. Exposed Pad VIN Supply Voltage Input. Rev. 1.0 May 2014 www.aosmd.com Page 2 of 15 AOZ1283 Absolute Maximum Ratings Recommended Operating Conditions Exceeding the Absolute Maximum Ratings may damage the device. The device is not guaranteed to operate beyond the Recommended Operating Conditions. Parameter Rating Supply Voltage (VIN) Parameter 40V -0.7V to VIN+ 0.3V LX to GND EN, SS, FB and COMP to GND -0.3V to +6V -0.3V to VLX + 6V BST to GND Junction Temperature (TJ) +150C Storage Temperature (TS) -65C to +150C ESD Rating (1) Rating Supply Voltage (VIN) 3.0V to 36V Output Voltage (VOUT) 0.8V to VIN*0.85V Ambient Temperature (TA) -40C to +85C Package Thermal Resistance EPAD SO-8 (JA) 50C/W 2kV Note: 1. Devices are inherently ESD sensitive, handling precautions are required. Human body model rating: 1.5k in series with 100pF. Electrical Characteristics TA = 25 C, VIN = 12V, VEN = 3V, VOUT = 3.3V, unless otherwise specified. Specifications in BOLD indicate a temperature range of -40C to +85C. These specifications are guaranteed by design. Symbol VIN VUVLO IIN Parameter Conditions Supply Voltage Input Under-Voltage Lockout Threshold Typ. 3 VIN rising VIN falling Supply Current (Quiescent) IOUT = 0, VFB = 1V, VEN > 1.2V IOFF Shutdown Supply Current VEN = 0V VFB Feedback Voltage TA = 25C VFB_LOAD Load Regulation Min. Max. 36 V 2.9 V V 1.5 mA 10 A 812 mV 2.3 1 788 800 Units 0.4A < Load < 3.6A 0.5 % Line Regulation Load = 2A 0.03 %/V Feedback Voltage Input Current VFB = 800mV 0.8 A VEN_OFF VEN_ON EN Input Threshold Off threshold On threshold VEN_HYS EN Input Hysteresis VFB_LINE IFB ENABLE 0.4 1.2 V V 200 mV 3 4 A 2 2.5 3 A 160 0.8 1.6 200 1 2 240 1.2 2.4 kHz MHz MHz CURRENT LIMIT Peak Current Limit SOFT START (SS) ISS Soft Start Source Current MODULATOR fO Frequency RF = 270k RF = 46.6k RF = 20k Maximum Duty Cycle fO = 1MHz 87 % Minimum On Time 150 ns Error Amplifier Voltage Gain 500 V/V GEA Error Amplifier Transconductance 170 A/V GCS Current Sense Circuit Transconductance 4.5 A/V DMAX TON_MIN GVEA Rev. 1.0 May 2014 www.aosmd.com Page 3 of 15 AOZ1283 Electrical Characteristics (continued) TA = 25 C, VIN = 12V, VEN = 3V, VOUT = 3.3V, unless otherwise specified. Specifications in BOLD indicate a temperature range of -40C to +85C. These specifications are guaranteed by design. Symbol Parameter Conditions Min. Typ. Max. Units 10 A 70 m POWER STATE OUTPUT ILEAKAGE NMOS Leakage VEN = 0V, VLX = 0V RDS(ON) NMOS On-Resistance VIN = 12V 50 THERMAL PROTECTION TSD Thermal Shutdown Threshold 145 C TSD_HYS Thermal Shutdown Hysteresis 45 C Rev. 1.0 May 2014 www.aosmd.com Page 4 of 15 AOZ1283 Block Diagram FSW VIN Regulator EN Enable Detect Current Sense SoftStart Ramp Generator BST LDO BST OC SS OSC CLK FB PWM Logic 0.8V Error Amplifier LX PWM Comparator GND COMP Rev. 1.0 May 2014 Driver www.aosmd.com Page 5 of 15 AOZ1283 Typical Performance Characteristics TA = 25C, VIN = 24V, VEN = 5V, VOUT = 5V, unless otherwise specified. Full Load Operation Light Load Operation IN Ripple Voltage (1V/div) IN Ripple Voltage (1V/div) OUT Ripple Voltage (1V/div) OUT Ripple Voltage (1V/div) LX Voltage (20V/div) LX Voltage (20V/div) Inductor Current (2A/div) Inductor Current (1A/div) 1s/div 1s/div Start Up to Full Load Short Circuit Protection LX Voltage (20V/div) OUT Voltage (2V/div) OUT Voltage (2V/div) IN Current (1A/div) Inductor Current (5A/div) 5ms/div 10ms/div 50% to 100% Load Transient Short Circuit Recovery LX Voltage (20V/div) OUT Voltage (0.5V/div) OUT Voltage (2V/div) OUT Current (1A/div) Inductor Current (5A/div) 10ms/div 100s/div Rev. 1.0 May 2014 www.aosmd.com Page 6 of 15 AOZ1283 Efficiency Curves Efficiency (Vo=5V, fs=600kHz) vs. Load Current 95 Efficiency (%) 90 85 12V-5V 36V-5V 80 24V-5V 75 70 65 60 0 0.5 1.0 1.5 Load Current (A) 2.0 2.5 Efficiency (Vo=3.3V, fs=600kHz) vs. Load Current 100 5V-3.3V 12V-3.3V 95 Efficiency (%) 90 85 80 36V-3.3V 75 24V-3.3V 70 65 60 0 Rev. 1.0 May 2014 0.5 1.5 1.0 Load Current (A) www.aosmd.com 2.0 2.5 Page 7 of 15 AOZ1283 Detailed Description The AOZ1283 is a current-mode step down regulator with integrated high side NMOS switch. It operates from a 3V to 36V input voltage range and supplies up to 4A of load current. Features include enable control, Power-On Reset, input under voltage lockout, external soft-start and thermal shut down. less than the error voltage, the internal high-side switch is on. The inductor current flows from the input through the inductor to the output. When the current signal exceeds the error voltage, the high-side switch is off. The inductor current is freewheeling through the Schottky diode to output. The AOZ1283 is available in EPAD SO-8 package. Switching Frequency Enable and Soft Start The AOZ1283 has external soft start feature to limit inrush current and ensure the output voltage ramps up smoothly to regulation voltage. A soft start process begins when the input voltage rises to 3V and voltage on EN pin is HIGH. In soft start process, a 2.5A internal current source charges the external capacitor at SS. As the SS capacitor is charged, the voltage at SS rises. The SS voltage clamps the reference voltage of the error amplifier, therefore output voltage rising time follows the SS pin voltage. With the slow ramping up output voltage, the inrush current can be prevented. Minimum external soft-start capacitor 850pF is required, and the corresponding soft-start time is about 200s. The EN pin of the AOZ1283 is active high. Connect the EN pin to a voltage between 1.2V to 5V if enable function is not used. Pull it to ground will disable the AOZ1283. Do not leave it open. The voltage on EN pin must be above 1.2V to enable the AOZ1283. When voltage on EN pin falls below 0.4V, the AOZ1283 is disabled. If an application circuit requires the AOZ1283 to be disabled, an open drain or open collector circuit should be used to interface to EN pin. Steady-State Operation Under steady-state conditions, the converter operates in fixed frequency and Continuous-Conduction Mode (CCM). The AOZ1283 integrates an internal N-MOSFET as the high-side switch. Inductor current is sensed by amplifying the voltage drop across the drain to source of the high side power MOSFET. Since the N-MOSFET requires a gate voltage higher than the input voltage, a boost capacitor connected between LX pin and BST pin drives the gate. The boost capacitor is charged while LX is low. An internal 10 switch from LX to GND is used to insure that LX is pulled to GND even in the light load. Output voltage is divided down by the external voltage divider at the FB pin. The difference of the FB pin voltage and reference is amplified by the internal transconductance error amplifier. The error voltage, which shows on the COMP pin, is compared against the current signal, which is sum of inductor current signal and ramp compensation signal, at PWM comparator input. If the current signal is Rev. 1.0 May 2014 The AOZ1283PI switching frequency can be programmed by an external resistor. The external resistor value can be calculated by the following formula: 50000 RF k = --------------------- - 5k f O kHz Some standard values of RF for most commonly used switching frequency are listed in Table 1. fo (Hz) RF (k) 200k 249 500k 100 1M 46.6 2M 20 Table 1. Output Voltage Programming Output voltage can be set by feeding back the output to the FB pin with a resistor divider network. In the application circuit shown in Figure 1. The resistor divider network includes R1 and R2. Usually, a design is started by picking a fixed R2 value and calculating the required R1 with equation below. R 1 V O = 0.8 1 + ------- R 2 Some standard values of R1 and R2 for the most commonly used output voltage values are listed in Table 2. Vo (V) www.aosmd.com R1 (k) R2 (k) 0.8 1.0 Open 1.2 4.99 10 1.5 10 11.5 1.8 12.7 10.2 2.5 21.5 10 3.3 31.6 10 5.0 52.3 10 Table 2. Page 8 of 15 AOZ1283 The combination of R1 and R2 should be large enough to avoid drawing excessive current from the output, which will cause power loss. Application Information Protection Features Input Capacitor The AOZ1283PI has multiple protection features to prevent system circuit damage under abnormal conditions. The input capacitor (C1 in Figure 1) must be connected to the VIN pin and GND pin of the AOZ1283 to maintain steady input voltage and filter out the pulsing input current. The voltage rating of input capacitor must be greater than maximum input voltage plus ripple voltage. Over Current Protection (OCP) The sensed inductor current signal is also used for over current protection. Since the AOZ1283 employs peak current mode control, the COMP pin voltage is proportional to the peak inductor current. The COMP pin voltage is limited to be between 0.4V and 2.5V internally. The peak inductor current is automatically limited cycle by cycle. The cycle by cycle current limit threshold is internally set. When the load current reaches the current limit threshold, the cycle by cycle current limit circuit turns off the high side switch immediately to terminate the current duty cycle. The inductor current stop rising. The cycle by cycle current limit protection directly limits inductor peak current. The average inductor current is also limited due to the limitation on peak inductor current. When cycle by cycle current limit circuit is triggered, the output voltage drops as the duty cycle decreasing. The AOZ1283 has internal short circuit protection to protect itself from catastrophic failure under output short circuit conditions. The FB pin voltage is proportional to the output voltage. Whenever FB pin voltage is below 0.2V, the short circuit protection circuit is triggered. Power-On Reset (POR) A power-on reset circuit monitors the input voltage. When the input voltage exceeds 2.9V, the converter starts operation. When input voltage falls below 2.3V, the converter will stop switching. The basic AOZ1283PI application circuit is shown in Figure 1. Component selection is explained as follows. The input ripple voltage can be approximated by equation below: VO VO IO V IN = ----------------- 1 - --------- --------f C IN V IN V IN Since the input current is discontinuous in a buck converter, the current stress on the input capacitor is another concern when selecting the capacitor. For a buck circuit, the RMS value of input capacitor current can be calculated by: VO VO - 1 - -------- I CIN_RMS = I O -------V IN V IN if we let m equal the conversion ratio: VO -------- = m V IN The relationship between the input capacitor RMS current and voltage conversion ratio is calculated and shown in Figure 2. It can be seen that when VO is half of VIN, CIN is under the worst current stress. The worst current stress on CIN is 0.5 x IO. 0.5 Thermal Protection 0.4 An internal temperature sensor monitors the junction temperature. It shuts down the internal control circuit and high side NMOS if the junction temperature exceeds 145C. The regulator will restart automatically under the control of soft-start circuit when the junction temperature decreases to 100C. ICIN_RMS(m) 0.3 IO 0.2 0.1 0 0 0.5 m 1 Figure 2. ICIN vs. Voltage Conversion Ratio Rev. 1.0 May 2014 www.aosmd.com Page 9 of 15 AOZ1283 For reliable operation and best performance, the input capacitors must have current rating higher than ICIN-RMS at worst operating conditions. Ceramic capacitors are preferred for input capacitors because of their low ESR and high ripple current rating. Depending on the application circuits, other low ESR tantalum capacitor or aluminum electrolytic capacitor may also be used. When selecting ceramic capacitors, X5R or X7R type dielectric ceramic capacitors are preferred for their better temperature and voltage characteristics. Note that the ripple current rating from capacitor manufactures is based on certain amount of life time. Further de-rating may be necessary for practical design requirement. The selected output capacitor must have a higher rated voltage specification than the maximum desired output voltage including ripple. De-rating needs to be considered for long term reliability. Output ripple voltage specification is another important factor for selecting the output capacitor. In a buck converter circuit, output ripple voltage is determined by inductor value, switching frequency, output capacitor value and ESR. It can be calculated by the equation below: 1 V O = I L ESR CO + ------------------------- 8fC O Inductor The inductor is used to supply constant current to output when it is driven by a switching voltage. For given input and output voltage, inductance and switching frequency together decide the inductor ripple current, which is: VO VO - I L = ----------- 1 - -------fL V IN where, CO is output capacitor value, and ESRCO is the equivalent series resistance of the output capacitor. When low ESR ceramic capacitor is used as output capacitor, the impedance of the capacitor at the switching frequency dominates. Output ripple is mainly caused by capacitor value and inductor ripple current. The output ripple voltage calculation can be simplified to: The peak inductor current is: I L I Lpeak = I O + -------2 1 V O = I L ------------------------- 8 f C O High inductance gives low inductor ripple current but requires larger size inductor to avoid saturation. Low ripple current reduces inductor core losses. It also reduces RMS current through inductor and switches, which results in less conduction loss. When selecting the inductor, make sure it is able to handle the peak current without saturation even at the highest operating temperature. The inductor takes the highest current in a buck circuit. The conduction loss on inductor needs to be checked for thermal and efficiency requirements. Surface mount inductors in different shape and styles are available from Coilcraft, Elytone and Murata. Shielded inductors are small and radiate less EMI noise. But they cost more than unshielded inductors. The choice depends on EMI requirement, price and size. Output Capacitor The output capacitor is selected based on the DC output voltage rating, output ripple voltage specification and ripple current rating. Rev. 1.0 May 2014 If the impedance of ESR at switching frequency dominates, the output ripple voltage is mainly decided by capacitor ESR and inductor ripple current. The output ripple voltage calculation can be further simplified to: V O = I L ESR CO For lower output ripple voltage across the entire operating temperature range, X5R or X7R dielectric type of ceramic, or other low ESR tantalum capacitor or aluminum electrolytic capacitor may also be used as output capacitors. In a buck converter, output capacitor current is continuous. The RMS current of output capacitor is decided by the peak to peak inductor ripple current. It can be calculated by: I L I CO_RMS = ---------12 Usually, the ripple current rating of the output capacitor is a smaller issue because of the low current stress. When the buck inductor is selected to be very small and inductor ripple current is high, output capacitor could be overstressed. www.aosmd.com Page 10 of 15 AOZ1283 Schottky Diode Selection The external freewheeling diode supplies the current to the inductor when the high side NMOS switch is off. To reduce the losses due to the forward voltage drop and recovery of diode, Schottky diode is recommended to use. The maximum reverse voltage rating of the chosen Schottky diode should be greater than the maximum input voltage, and the current rating should be greater than the maximum load current. When VIN is lower than 4.5V, such as 3.0V, an external 5V is required to add into the BST pin for proper operation. Loop Compensation The AOZ1283 employs peak current mode control for easy use and fast transient response. Peak current mode control eliminates the double pole effect of the output L&C filter. It greatly simplifies the compensation loop design. With peak current mode control, the buck power stage can be simplified to be a one-pole and one-zero system in frequency domain. The pole is dominant pole and can be calculated by: 1 2 CO RL The zero is a ESR zero due to output capacitor and its ESR. It is can be calculated by: fZ1 1 2 CO ESRCO GEA 2 CC GVEA GEA is the error amplifier transconductance, which is 200*10-6 A/V; GVEA is the error amplifier voltage gain, which is 500 V/V and CC is compensation capacitor. The zero given by the external compensation network, capacitor CC (C5 in Figure 1) and resistor RC (R1 in Figure 1), is located at: fZ 2 1 2 CC RC To design the compensation circuit, a target crossover frequency fC for close loop must be selected. The system crossover frequency is where control loop has unity gain. The crossover frequency is also called the converter bandwidth. Generally a higher bandwidth means faster response to load transient. However, the bandwidth should not be too high due to system stability concern. When designing the compensation loop, converter stability under all line and load condition must be considered. Usually, it is recommended to set the bandwidth to be less than 1/10 of switching frequency. where; CO is the output filter capacitor; RL is load resistor value and ESRCO is the equivalent series resistance of output capacitor. The compensation design is actually to shape the converter close loop transfer function to get desired gain and phase. Several different types of compensation network can be used for AOZ1283. For most cases, a series capacitor and resistor network connected to the COMP pin sets the pole-zero and is adequate for a stable high-bandwidth control loop. Rev. 1.0 May 2014 fP 2 where; Low Input operation fP 1 In the AOZ1283, FB pin and COMP pin are the inverting input and the output of internal transconductance error amplifier. A series R and C compensation network connected to COMP provides one pole and one zero. The pole is: The strategy for choosing RC and CC is to set the cross over frequency with RC and set the compensator zero with CC. Using selected crossover frequency, fC, to calculate RC: RC fC VO 2 CO VFB GEA GCS where; fC is desired crossover frequency; VFB is 0.8V; GEA is the error amplifier transconductance, which is 200*10-6 A/V and GCS is the current sense circuit transconductance, which is 4.5 A/V. www.aosmd.com Page 11 of 15 AOZ1283 The compensation capacitor CC and resistor RC together make a zero. This zero is put somewhere close to the dominate pole fp1 but lower than 1/5 of selected crossover frequency. CC can is selected by: CC T 1. 5 2 RC fP1 junction P -P -P total_loss diode_loss inductor_loss = ------------------------------------------------------------------------------------------------------------------------- +T JA ambient The maximum junction temperature of AOZ1283PI is 145C, which limits the maximum load current capability. Equation above can also be simplified to: CC The actual junction temperature can be calculated with power dissipation in the AOZ1283 and thermal impedance from junction to ambient. CO RL RC Easy to use application software which helps to design and simulate the compensation loop can be found at www.aosmd.com. Thermal Management and Layout Consideration In the AOZ1283 buck regulator circuit, high pulsing current flows through two circuit loops. The first loop starts from the input capacitors, to the VIN pin, to the LX pins, to the filter inductor, to the output capacitor and load, and then return to the input capacitor through ground. Current flows in the first loop when the high side switch is on. The second loop starts from inductor, to the output capacitors and load, to the GND pin of the AOZ1283, to the LX pins of the AOZ1283. Current flows in the second loop when the low side diode is on. In PCB layout, minimizing the two loops area reduces the noise of this circuit and improves efficiency. A ground plane is recommended to connect input capacitor, output capacitor, and GND pin of the AOZ1283. The thermal performance of the AOZ1283 is strongly affected by the PCB layout. Extra care should be taken by users during design process to ensure that the IC will operate under the recommended environmental conditions. Several layout tips are listed below for the best electric and thermal performance. 1. Do not use thermal relief connection to the VIN and the GND pin. Pour a maximized copper area to the GND pin and the VIN pin to help thermal dissipation. 2. Input capacitor should be connected to the VIN pin and the GND pin as close as possible. 3. Make the current trace from LX pins to L to Co to the GND as short as possible. 4. Pour copper plane on all unused board area and connect it to stable DC nodes, like VIN, GND or VOUT. 5. Keep sensitive signal trace such as trace connected with FB pin and COMP pin far away from the LX pins. In the AOZ1283 buck regulator circuit, the three major power dissipating components are the AOZ1283, external diode and output inductor. The total power dissipation of converter circuit can be measured by input power minus output power. P total_loss = V IN I IN - V O V IN The power dissipation of inductor can be approximately calculated by output current and DCR of inductor: P inductor_loss = IO2 R inductor 1.1 The power dissipation of diode is: VO P diodeloss = I O F V 1 - --------- V IN Rev. 1.0 May 2014 www.aosmd.com Page 12 of 15 AOZ1283 Package Dimensions, SO-8 EP1 Gauge plane 0.2500 D0 C L L1 E2 E1 E3 E L1' D1 Note 5 D 7 (4x) A2 e B A A1 Dimensions in millimeters RECOMMENDED LAND PATTERN 3.70 2.20 5.74 2.71 2.87 0.80 1.27 0.635 UNIT: mm Symbols A Min. 1.40 Nom. 1.55 A1 A2 B 0.00 1.40 0.31 0.05 1.50 0.406 C D D0 D1 E e E1 E2 E3 L y | L1-L1' | L1 0.17 4.80 3.20 3.10 5.80 -- 3.80 2.21 -- 4.96 3.40 3.30 6.00 1.27 3.90 2.41 0.40 REF 0.40 0.95 -- -- 0 -- Max. 1.70 0.10 1.60 0.51 0.25 5.00 3.60 3.50 6.20 -- 4.00 2.61 1.27 0.10 8 3 0.04 0.12 1.04 REF Dimensions in inches Symbols A A1 A2 B C D D0 D1 E e E1 E2 E3 L y | L1-L1' | L1 Min. 0.055 0.000 0.055 0.012 0.007 0.189 Nom. 0.061 0.002 Max. 0.067 0.004 0.059 0.016 -- 0.063 0.020 0.010 0.195 0.197 0.134 0.142 0.130 0.138 0.236 0.244 0.050 -- 0.153 0.157 0.095 0.103 0.016 REF 0.016 0.037 0.050 -- 0.004 -- 0.126 0.122 0.228 -- 0.150 0.087 0 -- 3 8 0.002 0.005 0.041 REF Notes: 1. Package body sizes exclude mold flash and gate burrs. 2. Dimension L is measured in gauge plane. 3. Tolerance 0.10mm unless otherwise specified. 4. Controlling dimension is millimeter, converted inch dimensions are not necessarily exact. 5. Die pad exposure size is according to lead frame design. 6. Followed from JEDEC MS-012 Rev. 1.0 May 2014 www.aosmd.com Page 13 of 15 AOZ1283 Tape and Reel Dimensions, SO-8 EP1 Carrier Tape P1 D1 P2 T E1 E2 E B0 K0 A0 D0 P0 Feeding Direction UNIT: mm Package SO-8 (12mm) A0 6.40 0.10 B0 K0 D0 5.20 0.10 2.10 0.10 1.60 0.10 D1 1.50 0.10 E 12.00 0.10 Reel E1 1.75 0.10 E2 5.50 0.10 P0 8.00 0.10 P1 4.00 0.10 P2 T 2.00 0.10 0.25 0.10 W1 S G N M K V R H W UNIT: mm N W Tape Size Reel Size M 12mm o330 o330.00 o97.00 13.00 0.10 0.30 0.50 W1 17.40 1.00 H K o13.00 10.60 +0.50/-0.20 S 2.00 0.50 G -- R -- V -- Leader/Trailer and Orientation Trailer Tape 300mm min. or 75 empty pockets Rev. 1.0 May 2014 Components Tape Orientation in Pocket www.aosmd.com Leader Tape 500mm min. or 125 empty pockets Page 14 of 15 AOZ1283 Part Marking AOZ1283PI (SO-8) Z1283PI FAYWLT Part Number Code Assembly Lot Code Fab & Assembly Location Year & Week Code LEGAL DISCLAIMER Alpha and Omega Semiconductor makes no representations or warranties with respect to the accuracy or completeness of the information provided herein and takes no liabilities for the consequences of use of such information or any product described herein. Alpha and Omega Semiconductor reserves the right to make changes to such information at any time without further notice. This document does not constitute the grant of any intellectual property rights or representation of non-infringement of any third-party's intellectual property rights. Customer shall comply with applicable legal requirements, including all applicable export control rules, regulations, and limitations. LIFE SUPPORT POLICY ALPHA AND OMEGA SEMICONDUCTOR PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user. Rev. 1.0 May 2014 2. A critical component in any component of a life support, device, or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. www.aosmd.com Page 15 of 15