160 MHz SAW Filter 30 MHz Bandwidth Part Number: SF0160BA01961S DESCRIPTION * * * 160 MHz SAW bandpass filter with 30 MHz bandwidth. 13.3 x 6.5 mm LCC package. RoHS compliant. TYPICAL PERFORMANCE Horizontal: Vertical from Top: S11 (60 to 260 MHz) Frequency : Relative Magnitude : Relative magnitude : Phase Linearity : 20 10 1 10 MHz/div dB/div dB/div deg/div S22 (60 to 260 MHz) Spectrum Microwave 400 Nickerson Road, Marlborough, MA 01752, USA * Phone 1-508-251-6400 * Fax 1-508-251-6401 www.SpectrumMicrowave.com DSSF0160BA01961S Rev A 15-Mar-2010 ECN 36650 Page 1 of 3 160 MHz SAW Filter 30 MHz Bandwidth Part Number: SF0160BA01961S SPECIFICATION Parameter Center Frequency (Fc) 1,3 Insertion Loss 1 dB Bandwidth 3 dB Bandwidth 40 dB Bandwidth Passband Amplitude Ripple 2 Phase Ripple( Fc +/- 15 MHz) 2 Rejection: 10 - 135 MHz 185 - 280 MHz 270 - 370 MHz VSWR ( Fc +/- 15 MHz) Ambient Temperature (Tref) Notes: Min 159.75 30 40 40 20 4.4 - Typ 160.0 12.2 33.0 35.0 44.0 0.8 9 50 50 25 6 25 Max 160.25 14 50 1 12 - Units MHz dB MHz MHz MHz dB p-p deg p-p dB dB dB dB C 1. Average of the lower and upper 3 dB band edge frequencies. 2. When used in the suggested matching network. 3. Typical change of filter frequency response with temperature is f = (T-Tref)*Tc*Fc, in ppm. MAXIMUM RATINGS Parameter Storage Temperature Range Operating Temperature Range (T) Temperature Coefficient of Frequency (Tc) 3 Input Power Level Min Typ Max Units -40 -20 - 25 25 -94 10 85 70 13 C C ppm/C dBm MATCHING CIRCUIT Ls1 Input 50 Single-ended 12 6 Lp2 Lp1 11 Output 50 Single-ended 5 Typical component values: Ls1 Lp1 = = 47 43 nH nH Ls2 = 47 nH Notes: 1. Recommend use of 2% tolerance matching components. Inductor Q=45. 2. Component values are for reference only and may change depending on board layout. Spectrum Microwave 400 Nickerson Road, Marlborough, MA 01752, USA * Phone 1-508-251-6400 * Fax 1-508-251-6401 www.SpectrumMicrowave.com DSSF0160BA01961S Rev A 15-Mar-2010 ECN 36650 Page 2 of 3 160 MHz SAW Filter 30 MHz Bandwidth Part Number: SF0160BA01961S PACKAGE OUTLINE SUGGESTED FOOTPRINT Units: mm Tolerances are 0.15 mm except where indicated and for the overall length and width, which are nominal values. Pad Configuration: Package Material: Body: Al2O3 ceramic Lid: Kovar, Ni plated Terminations: Au plating 1 m min, over a 1.3-8.9 m Ni plating Input: Input return: Output: Output return: Ground: 11 12 5 6 All other pads ISO 9001 Registered All specifications are believed to be accurate and reliable. However, Spectrum Microwave reserves the right to make changes without notice. (c) 2010 All rights reserved. Spectrum Microwave 400 Nickerson Road, Marlborough, MA 01752, USA * Phone 1-508-251-6400 * Fax 1-508-251-6401 www.SpectrumMicrowave.com DSSF0160BA01961S Rev A 15-Mar-2010 ECN 36650 Page 3 of 3