
US
UK
Taiwan
China
+1-847-639-6400 sales@coilcraft.com
+44-1236-730595 sales@coilcraft-europe.com
+886-2-2264 3646 sales@coilcraft.com.tw
+86-21-6218 8074 sales@coilcraft.com.cn
+ 65-6484 8412 sales@coilcraft.com.sg
© Coilcraft Inc. 2017
This product may not be used in medical or high
risk applications without prior Coilcraft appr
oval.
Specification subject to change without notice.
Please check web site for latest infor
SMT Data Line EMI Filter
CCDLF
Document 511-1
Document 511-1 Revised 12/14/16
1. When ordering, please specify termination and packaging codes:
CCDLF 8500LD
Termination L = RoHS compliant tin-silver-copper over silver-platinum
Special order: S = non-RoHS tin-lead (63/37).
Packaging D = 13″ machine ready reel. EIA-481 embossed plastic
tape (1000 parts per full reel).
B = Less than full reel. In tape, but not machine ready.
To have a leader and trailer added ($25 charge), use
code letter D instead.
Designer’s Kit D303 contains four each of the CCDLF 10000, DLF,
CDF and PDLF filters
Core material Ferrite
Terminations RoHS compliant tin-silver-copper over silver-platinum.
Weight 670 mg
Ambient temperature –40°C to +85°C
Storage temperature Component: –40°C to +85°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packaging 1000/13″ reel Plastic tape: 16 mm wide,
10.28 mm thick, 12 mm pocket spacing, 5.0 mm pocket depth
PCB washing Tested to MIL-STD-202 Method 215 plus an additional
aqueous wash. See Doc787_PCB_Washing.pdf.
• See our PDLF series for 4, 3 and 2-line EMI filters and CDF
for 8-line filters
• Exceptional common mode noise attenuation from 15 MHz
to 300 MHz; passes signal line data below 300 MHz with
minimal attenuation
Dimensions are in inches
mm
Common mode Cutoff
peak impedance frequency2 Inductance DCR max4 Isolation5 Current6
Part number1 Lines (Ohms) (GHz)
min (µH)3 (mOhms) (Vrms) (mAdc)
CCDLF 10000L_ 10 523.54 @ 43 MHz 0.043 5 250 300 100
2. Frequency at which the differential mode attenuation equals −3 dB
3. Inductance shown for each winding, measured at 1 MHz
4. DCR is for each winding.
5. Interwinding isolation (hipot) tested for one minute.
6. Current rating is for each line.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
0.170
4,32 max
0.050
1,27 cen
0.030
0,76
0.020
0,51
0.050
1,27
0.230
5,84
0.270
6,86
5
11
4
12
1
15
20
6
197
18
8
17
9
16
10
2
14
3
13
Recommended
9,14
0.050
1,27
0.030
0,76
0.040
1,02
0.060
1,52
max
cen
typref
20
1
0.360
9,14 max
15
14
13
12
11
6
7
8
9
10
Dot indicates pin 1
Internal code
CCDLF 10000L
X
& buy
& FAQ
softw