DS90LV027AH DS90LV027AH High Temperature LVDS Dual Differential Driver Literature Number: SNLS206 DS90LV027AH High Temperature LVDS Dual Differential Driver General Description Features The DS90LV027AH is a dual LVDS driver device optimized for high data rate and low power applications. The device is designed to support data rates in excess of 600Mbps (300MHz) utilizing Low Voltage Differential Signaling (LVDS) technology. The DS90LV027AH is a current mode driver allowing power dissipation to remain low even at high frequency. In addition, the short circuit fault current is also minimized. The device is in a 8-lead small outline package. The DS90LV027AH has a flow-through design for easy PCB layout. The differential driver outputs provides low EMI with its typical low output swing of 360 mV. It is perfect for high speed transfer of clock and data. The DS90LV027AH can be paired with its companion dual line receiver, the DS90LV028AH, or with any of National's LVDS receivers, to provide a high-speed point-to-point LVDS interface. n n n n n n n n n n -40C to +125C operating temperature range > 600 Mbps (300MHz) switching rates 0.3 ns typical differential skew 0.7 ns maximum differential skew 3.3V power supply design Low power dissipation (46 mW @ 3.3V static) Flow-through design simplifies PCB layout Power Off Protection (outputs in high impedance) Conforms to TIA/EIA-644 Standard 8-Lead SOIC package saves space Connection Diagram Dual-In-Line 20165101 Order Number DS90LV027AHM See NS Package Number M08A Functional Diagram 20165102 20165103 (c) 2005 National Semiconductor Corporation DS201651 www.national.com DS90LV027AH High Temperature LVDS Dual Differential Driver September 2005 DS90LV027AH Absolute Maximum Ratings (Note 1) ESD Ratings Supply Voltage (VCC) -0.3V to +4V Input Voltage (DI) -0.3V to +3.6V Output Voltage (DO ) -0.3V to +3.9V 1000V (CDM) 1000V Min Typ Max Supply Voltage (VCC) 3.0 3.3 3.6 V Temperature (TA) -40 25 +125 C 9.5 mW/C above +25C Storage Temperature Range -65C to +150C Lead Temperature Range Soldering (4 sec.) 4kV Recommended Operating Conditions 1190 mW Derate M Package (EIAJ 0 , 200 pF) (IEC direct 330 , 150 pF) Maximum Package Power Dissipation @ +25C M Package 8kV (HBM 1.5 k, 100 pF) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Units +260C Electrical Characteristics Over Supply Voltage and Operating Temperature ranges, unless otherwise specified. (Notes 2, 3, 7) Symbol Parameter Conditions Pin Min Typ Max Units DO+, DO- 250 360 450 mV 1 35 mV 1.4 1.6 DIFFERENTIAL DRIVER CHARACTERISTICS VOD Output Differential Voltage VOD VOD Magnitude Change RL = 100 (Figure 1) VOH Output High Voltage VOL Output Low Voltage VOS Offset Voltage VOS Offset Magnitude Change IOXD Power-off Leakage IOSD Output Short Circuit Current VIH Input High Voltage VIL Input Low Voltage IIH Input High Current VIN = 3.3V or 2.4V IIL Input Low Current VIN = GND or 0.5V VCL Input Clamp Voltage ICL = -18 mA ICC Power Supply Current No Load 0.9 1.1 1.125 1.2 0 VOUT = VCC or GND, VCC = 0V DI V mV 3 25 10 A -5.7 -8 mA VCC V 2.0 0.8 V 10 10 A 8 14 mA 14 20 mA 2 1 -1.5 1.375 1 GND VIN = VCC or GND V V A -0.6 VCC RL = 100 V Switching Characteristics Over Supply Voltage and Operating Temperature Ranges, unless otherwise specified. (Notes 3, 4, 5, 6) Symbol Parameter Conditions Min Typ Max Units ns DIFFERENTIAL DRIVER CHARACTERISTICS tPHLD Differential Propagation Delay High to Low RL = 100, CL = 15 pF 0.3 0.8 2.0 tPLHD Differential Propagation Delay Low to High (Figure 2 and Figure 3) 0.3 1.1 2.0 ns tSKD1 Differential Pulse Skew |tPHLD - tPLHD| (Note 8) 0 0.3 0.7 ns 0.4 tSKD2 Channel to Channel Skew (Note 9) 0 0.8 ns tSKD3 Differential Part to Part Skew (Note 10) 0 1.0 ns tSKD4 Differential Part to Part Skew (Note 11) 0 1.2 ns tTLH Transition Low to High Time 0.2 0.5 1.0 ns tTHL Transition High to Low Time 0.2 0.5 1.0 fMAX Maximum Operating Frequency (Note 12) 350 ns MHz Note 1: "Absolute Maximum Ratings" are those values beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the devices should be operated at these limits. The table of "Electrical Characteristics" specifies conditions of device operation. Note 2: Current into device pins is defined as positive. Current out of device pins is defined as negative. All voltages are referenced to ground except VOD. Note 3: All typicals are given for: VCC = +3.3V and TA = +25C. Note 4: These parameters are guaranteed by design. The limits are based on statistical analysis of the device over PVT (process, voltage, temperature) ranges. Note 5: CL includes probe and fixture capacitance. www.national.com 2 (Continued) Note 6: Generator waveform for all tests unless otherwise specified: f = 1 MHz, ZO = 50, tr 1 ns, tf 1 ns (10%-90%). Note 7: The DS90LV027AH is a current mode device and only function with datasheet specification when a resistive load is applied to the drivers outputs. Note 8: tSKD1, |tPHLD - tPLHD|, is the magnitude difference in differential propagation delay time between the positive going edge and the negative going edge of the same channel. Note 9: tSKD2 is the Differential Channel to Channel Skew of any event on the same device. Note 10: tSKD3, Differential Part to Part Skew, is defined as the difference between the minimum and maximum specified differential propagation delays. This specification applies to devices at the same VCC and within 5C of each other within the operating temperature range. Note 11: tSKD4, part to part skew, is the differential channel to channel skew of any event between devices. This specification applies to devices over recommended operating temperature and voltage ranges, and across process distribution. tSKD4 is defined as |Max - Min| differential propagation delay. Note 12: fMAX generator input conditions: tr = tf < 1 ns (0% to 100%), 50% duty cycle, 0V to 3V. Output criteria: duty cycle = 45%/55%, VOD > 250mV, all channels switching. Parameter Measurement Information 20165104 FIGURE 1. Differential Driver DC Test Circuit 20165105 FIGURE 2. Differential Driver Propagation Delay and Transition Time Test Circuit 20165106 FIGURE 3. Differential Driver Propagation Delay and Transition Time Waveforms 3 www.national.com DS90LV027AH Switching Characteristics DS90LV027AH Application Information TABLE 1. Device Pin Descriptions Pin # Name Description 2, 3 DI TTL/CMOS driver input pins 6, 7 DO+ Non-inverting driver output pin 5, 8 DO- Inverting driver output pin 4 GND Ground pin 1 VCC Positive power supply pin, +3.3V 0.3V Typical Performance Curves Output High Voltage vs Power Supply Voltage Output Low Voltage vs Power Supply Voltage 20165107 20165108 Output Short Circuit Current vs Power Supply Voltage Differential Output Voltage vs Power Supply Voltage 20165110 20165109 www.national.com 4 DS90LV027AH Typical Performance Curves (Continued) Differential Output Voltage vs Load Resistor Offset Voltage vs Power Supply Voltage 20165111 20165112 Power Supply Current vs Frequency Power Supply Current vs Power Supply Voltage 20165114 20165113 5 www.national.com DS90LV027AH Typical Performance Curves (Continued) Power Supply Current vs Ambient Temperature Differential Propagation Delay vs Power Supply Voltage 20165115 20165116 Differential Propagation Delay vs Ambient Temperature Differential Skew vs Power Supply Voltage 20165118 20165117 www.national.com 6 DS90LV027AH Typical Performance Curves (Continued) Differential Skew vs Ambient Temperature Transition Time vs Power Supply Voltage 20165119 20165120 Transition Time vs Ambient Temperature 20165121 7 www.national.com DS90LV027AH High Temperature LVDS Dual Differential Driver Physical Dimensions inches (millimeters) unless otherwise noted Order Number DS90LV027AHM NS Package Number M08A National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. For the most current product information visit us at www.national.com. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. BANNED SUBSTANCE COMPLIANCE National Semiconductor manufactures products and uses packing materials that meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ``Banned Substances'' as defined in CSP-9-111S2. Leadfree products are RoHS compliant. National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated