Semiconductor Components Industries, LLC, 2001
March, 2001 – Rev. 8 1Publication Order Number:
TL431/D
Programmable
Precision References
The TL431, A, B integrated circuits are three–terminal
programmable shunt regulator diodes. These monolithic IC voltage
references operate as a low temperature coefficient zener which is
programmable from Vref to 36 V with two external resistors. These
devices exhibit a wide operating current range of 1.0 mA to 100 mA
with a typical dynamic impedance of 0.22 Ω. The characteristics of
these references make them excellent replacements for zener diodes in
many applications such as digital voltmeters, power supplies, and op
amp circuitry. The 2.5 V reference makes it convenient to obtain a
stable reference from 5.0 V logic supplies, and since the TL431, A, B
operates as a shunt regulator, it can be used as either a positive or
negative voltage reference.
•Programmable Output Voltage to 36 V
•Voltage Reference Tolerance: ±0.4%, Typ @ 25°C (TL431B)
•Low Dynamic Output Impedance, 0.22 Ω Typical
•Sink Current Capability of 1.0 mA to 100 mA
•Equivalent Full–Range Temperature Coefficient of 50 ppm/°C
Typical
•Temperature Compensated for Operation over Full Rated Operating
Temperature Range
•Low Output Noise Voltage
ORDERING INFORMATION
Device Operating
Temperature Range Package
TL431CLP, ACLP, BCLP TO–92
TL431CP, ACP, BCP
T 0°to +70°C
Plastic
TL431CDM, ACDM, BCDM TA = 0° to +70°CMICRO–8
TL431CD, ACD, BCD SOP–8
TL431ILP, AILP, BILP TO–92
TL431IP, AIP, BIP
T40°to +85°C
Plastic
TL431IDM, AIDM, BIDM TA = –40° to +85°CMICRO–8
TL431ID, AID, BID SOP–8
TL431, A, B
Series
PROGRAMMABLE
PRECISION REFERENCES
(Top
View)
3
1Reference
N/C
N/C
N/C
2
4
8
7
6
5N/C
Anode
N/C
Cathode
Anode Anode
LP SUFFIX
PLASTIC PACKAGE
CASE 29
(TO–92)
P SUFFIX
PLASTIC PACKAGE
CASE 626
D SUFFIX
PLASTIC PACKAGE
CASE 751
(SOP–8)
Pin 1. Reference
2. Anode
3. Cathode
(Top View)
3
1Reference
N/C
2
4
8
7
6
5N/C
Cathode
SOP–8 is a n i n t e rnally modified SO–8 package. Pins 2,
3, 6 and 7 are electrically common to the die attach flag.
This internal lead frame modification decreases power
nal dimensions of the standard SO–8 package.
DM SUFFIX
PLASTIC PACKAGE
CASE 846A
(MICRO–8)
8
1
81
8
1
SEMICONDUCTOR
TECHNICAL DATA
123
TL431, A, B Series
http://onsemi.com
2
Representative Block Diagram
1.0 k
Cathode
(K)
2.5 Vref
Anode (A)
Reference
(R)
4.0 k
150
Symbol
10 k
20 pF
800
Cathode (K)
3.28 k
Representative Schematic Diagram
Component values are nominal
Anode (A)
-
+
Anode
(A)
800
Reference
(R)
2.4 k 7.2 k
20 pF
800
Cathode
(K)
Reference
(R)
This device contains 12 active transistors.
MAXIMUM RATINGS (Full operating ambient temperature range applies, unless
otherwise noted.)
Rating Symbol Value Unit
Cathode to Anode Voltage VKA 37 V
Cathode Current Range, Continuous IK–100 to +150 mA
Reference Input Current Range, Continuous Iref –0.05 to +10 mA
Operating Junction Temperature TJ150 °C
Operating Ambient Temperature Range TA°C
TL431I, TL431AI, TL431BI –40 to +85
TL431C, TL431AC, TL431BC 0 to +70
Storage Temperature Range Tstg –65 to +150 °C
Total Power Dissipation @ TA = 25°C PDW
Derate above 25°C Ambient Temperature
D, LP Suffix Plastic Package 0.70
P Suffix Plastic Package 1.10
DM Suffix Plastic Package 0.52
Total Power Dissipation @ TC = 25°C PDW
Derate above 25°C Case Temperature
D, LP Suffix Plastic Package 1.5
P Suffix Plastic Package 3.0
NOTE: ESD data available upon request.
RECOMMENDED OPERATING CONDITIONS
Condition Symbol Min Max Unit
Cathode to Anode Voltage VKA Vref 36 V
Cathode Current IK1.0 100 mA
THERMAL CHARACTERISTICS
Characteristic Symbol D, LP Suffix
Package P Suffix
Package DM Suffix
Package Unit
Thermal Resistance, Junction–to–Ambient RθJA 178 114 240 °C/W
Thermal Resistance, Junction–to–Case RθJC 83 41 – °C/W
TL431, A, B Series
http://onsemi.com
3
ELECTRICAL CHARACTERISTICS (TA = 25°C, unless otherwise noted.)
TL431I TL431C
Characteristic Symbol Min Typ Max Min Typ Max Unit
Reference Input Voltage (Figure 1) Vref V
VKA = Vref, IK = 10 mA
TA = 25°C 2.44 2.495 2.55 2.44 2.495 2.55
TA = Tlow to Thigh (Note 1) 2.41 – 2.58 2.423 – 2.567
Reference Input Voltage Deviation Over ∆Vref – 7.0 30 – 3.0 17 mV
Temperature Range (Figure 1, Notes 1, 2)
VKA= Vref, IK = 10 mA
Ratio of Change in Reference Input Voltage V
ref
mV/V
to Change in Cathode to Anode Voltage
V
re
f
V
KA
IK = 10 mA (Figure 2),
V
KA
∆VKA = 10 V to V ref – –1.4 –2.7 – –1.4 –2.7
∆VKA = 36 V to 10 V – –1.0 –2.0 – –1.0 –2.0
Reference Input Current (Figure 2) Iref µA
IK = 10 mA, R1 = 10 k, R2 = ∞
TA = 25°C – 1.8 4.0 – 1.8 4.0
TA = Tlow to Thigh (Note 1) – – 6.5 – – 5.2
Reference Input Current Deviation Over ∆Iref – 0.8 2.5 – 0.4 1.2 µA
Temperature Range (Figure 2, Note 1, 4)
IK = 10 mA, R1 = 10 k, R2 = ∞
Minimum Cathode Current For Regulation Imin – 0.5 1.0 – 0.5 1.0 mA
VKA = Vref (Figure 1)
Off–State Cathode Current (Figure 3) Ioff – 260 1000 – 260 1000 nA
VKA = 36 V, Vref = 0 V
Dynamic Impedance (Figure 1, Note 3) |ZKA| – 0.22 0.5 – 0.22 0.5 Ω
VKA = Vref, ∆IK = 1.0 mA to 100 mA
f ≤ 1.0 kHz
NOTES: 1.Tlow = –40°C for TL431AIP TL431AILP, TL431IP, TL431ILP, TL431BID, TL431BIP, TL431BILP, TL431AIDM, TL431IDM, TL431BIDM
=0°C for TL431ACP, TL431ACLP, TL431CP, TL431CLP, TL431CD, TL431ACD, TL431BCD, TL431BCP, TL431BCLP, TL431CDM,
TL431ACDM, TL431BCDM
Thigh = +85°C for TL431AIP, TL431AILP, TL431IP, TL431ILP, TL431BID, TL431BIP, TL431BILP, TL431IDM, TL431AIDM, TL431BIDM
= +70°C for TL431ACP, TL431ACLP, TL431CP, TL431ACD, TL431BCD, TL431BCP, TL431BCLP, TL431CDM, TL431ACDM, TL431BCDM
2.The deviation parameter ∆Vref is defined as the difference between the maximum and minimum values obtained over the full operating ambient
temperature range that applies.
∆Vref = Vref max
-Vref min
∆TA = T2 - T1
T2
Ambient Temperature
T1
Vref min
Vref max
The average temperature coefficient of the reference input voltage, αVref is defined as:
Vref ppm
CVref
Vref @25CX10
6
TA
Vref x10
6
TA(Vref @25C)
αVref can be positive or negative depending on whether Vref Min or Vref Max occurs at the lower ambient temperature. (Refer to Figure 6.)
Example : Vref 8.0 mV and slope is positive,
Vref @25C2.495 V,TA70CVref 0.008 x 106
70 (2.495) 45.8 ppmC
3.The dynamic impedance ZKA is defined as |ZKA|
VKA
IK
When the device is programmed with two external resistors, R1 and R2, (refer to Figure 2) the total dynamic impedance of the circuit is defined as:
|ZKA||ZKA|1R1
R2
TL431, A, B Series
http://onsemi.com
4
ELECTRICAL CHARACTERISTICS (TA = 25°C, unless otherwise noted.)
TL431AI TL431AC TL431BI
Characteristic Symbol Min Typ Max Min Typ Max Min Typ Max Unit
Reference Input Voltage (Figure 1) Vref V
VKA = Vref, IK = 10 mA
TA = 25°C 2.47 2.495 2.52 2.47 2.495 2.52 2.483 2.495 2.507
TA = Tlow to Thigh 2.44 – 2.55 2.453 – 2.537 2.475 2.495 2.515
Reference Input Voltage Deviation Over ∆Vref – 7.0 30 – 3.0 17 – 3.0 17 mV
Temperature Range (Figure 1, Notes 1, 2)
VKA= Vref, IK = 10 mA
Ratio of Change in Reference Input Voltage V
ref
mV/V
to Change in Cathode to Anode Voltage
V
re
f
V
KA
IK = 10 mA (Figure 2),
V
KA
∆VKA = 10 V to V ref – –1.4 –2.7 – –1.4 –2.7 – –1.4 –2.7
∆VKA = 36 V to 10 V – –1.0 –2.0 – –1.0 –2.0 – –1.0 –2.0
Reference Input Current (Figure 2) Iref µA
IK = 10 mA, R1 = 10 k, R2 = ∞
TA = 25°C – 1.8 4.0 – 1.8 4.0 – 1.1 2.0
TA = Tlow to Thigh (Note 1) – – 6.5 – – 5.2 – – 4.0
Reference Input Current Deviation Over ∆Iref – 0.8 2.5 – 0.4 1.2 – 0.8 2.5 µA
Temperature Range (Figure 2, Note 1)
IK = 10 mA, R1 = 10 k, R2 = ∞
Minimum Cathode Current For Regulation Imin – 0.5 1.0 – 0.5 1.0 – 0.5 1.0 mA
VKA = Vref (Figure 1)
Off–State Cathode Current (Figure 3) Ioff – 260 1000 – 260 1000 – 230 500 nA
VKA = 36 V, Vref = 0 V
Dynamic Impedance (Figure 1, Note 3) |ZKA| – 0.22 0.5 – 0.22 0.5 – 0.14 0.3 Ω
VKA = Vref, ∆IK = 1.0 mA to 100 mA
f ≤ 1.0 kHz
NOTES: 1.Tlow = –40°C for TL431AIP TL431AILP, TL431IP, TL431ILP, TL431BID, TL431BIP, TL431BILP, TL431AIDM, TL431IDM, TL431BIDM
=0°C for TL431ACP, TL431ACLP, TL431CP, TL431CLP, TL431CD, TL431ACD, TL431BCD, TL431BCP, TL431BCLP, TL431CDM,
TL431ACDM, TL431BCDM
Thigh = +85°C for TL431AIP, TL431AILP, TL431IP, TL431ILP, TL431BID, TL431BIP, TL431BILP, TL431IDM, TL431AIDM, TL431BIDM
= +70°C for TL431ACP, TL431ACLP, TL431CP, TL431ACD, TL431BCD, TL431BCP, TL431BCLP, TL431CDM, TL431ACDM, TL431BCDM
2.The deviation parameter ∆Vref is defined as the difference between the maximum and minimum values obtained over the full operating ambient
temperature range that applies.
∆Vref = Vref max
-Vref min
∆TA = T2 - T1
T2
Ambient Temperature
T1
Vref min
Vref max
The average temperature coefficient of the reference input voltage, αVref is defined as:
Vref ppm
CVref
Vref @25CX10
6
TA
Vref x10
6
TA(Vref @25C)
αVref can be positive or negative depending on whether Vref Min or Vref Max occurs at the lower ambient temperature. (Refer to Figure 6.)
Example : Vref 8.0 mV and slope is positive,
Vref @25C2.495 V,TA70CVref 0.008 x 106
70 (2.495) 45.8 ppmC
3.The dynamic impedance ZKA is defined as |ZKA|
VKA
IK
When the device is programmed with two external resistors, R1 and R2, (refer to Figure 2) the total dynamic impedance of the circuit is defined as:
|ZKA||ZKA|1R1
R2
TL431, A, B Series
http://onsemi.com
5
IK
Vref
VKA
Input
Figure 1. Test Circuit for VKA = Vref
Input
IK
R2
Iref
Vref
VKA
R1
Figure 2. Test Circuit for VKA > Vref
VKA Vref1 R1
R2IrefR1
Ioff
Input VKA
Figure 3. Test Circuit for Ioff
-1.0
IMin
200
400
VKA, CATHODE VOLTAGE (V)
-200 0
0
1.0 2.0 3.0
800
600
-2.0 -1.0 0
-100 1.0 2.0 3.0
150
50
VKA, CATHODE VOLTAGE (V)
0
-50
Figure 4. Cathode Current versus
Cathode Voltage Figure 5. Cathode Current versus
Cathode Voltage
Input
100
VKA = Vref
TA = 25°C
IK
VKA
IK, CATHODE CURRENT (mA)
IK, CATHODE CURRENT ( A)µ
125
TA, AMBIENT TEMPERATURE (°C)
3.0
10050 75-55
0
2.5
0.5
2.0
1.0
250-25
1.5
2600
2580
2560
2540
2520
2500
2480
2460
VKA = Vref
IK = 10 mA
TA, AMBIENT TEMPERATURE (°C)
VKA
IK
-55
Input
Vref
75 100 125
2440
050
Figure 6. Reference Input Voltage versus
Ambient Temperature Figure 7. Reference Input Current versus
Ambient Temperature
2420
2400 25-25
Input
IK
IK = 10 mA
Iref
10k
VKA
ref
V , REFERENCE INPUT VOLTAGE (mV)
Iref, REFERENCE INPUT CURRENT ( A)µ
Vref Max = 2550 mV
Vref Typ = 2495 mV
Vref Min = 2440 mV
VKA = Vref
TA = 25°C
Input VKA
IK
TL431, A, B Series
http://onsemi.com
6
√
NOISE VOLTAGE (nV/ Hz)
-55
f, FREQUENCY (MHz)
100
10
1.0
100 k 10 M1.0 M1.0 k 10 k
0.1 75-25 0 25 50 100 125
TA, AMBIENT TEMPERATURE (C)
0.200
0.220
0.240
0.300
0.320
0.260
0.280
IK
50 -
1.0 k
+
Output
Gnd Output
Gnd
IK
50 -
1.0k
+
VKA = Vref
∆ IK = 1.0 mA to 100 mA
f ≤ 1.0 kHz
TA = 25C
∆ IK = 1.0 mA to 100 mA
|ZKA Ω|, DYNAMIC IMPEDANCE ( )
|ZKA Ω|, DYNAMIC IMPEDANCE ( )
f, FREQUENCY (Hz)
40
10 10 k1.0 k100
0
20
100 k
60
f, FREQUENCY (MHz)
100 k
0
10 M1.0 M
-10
10
20
30
60
50
40
1.0 k 10 k
VKA = Vref
IK = 10 mA
TA = 25°C
IK
OutputInput
80
, OPEN LOOP VOLTAGE GAIN (dB)
230
Gnd
Output
IK
9.0 µF
8.25k
15k
IK = 10 mA
TA = 25C
-55
0.01
100
10
1.0
0.1
TA, AMBIENT TEMPERATURE (5C)
75-25 0 25 50 100 125
40
1.0 k
VKA, CATHODE VOLTAGE (V)
30100
-32
-8.0
-16
20
0
-24 R2 Vref
R1 IK
Input VKA
Input Ioff
VKA = 36 V
Vref = 0 V VKA
Vref, REFERENCE INPUT VOLTAGE (mV)∆
Ioff, OFF-STATE CATHODE CURRENT (nA)
IK = 10 mA
TA = 25°C
Figure 8. Change in Reference Input
Voltage versus Cathode Voltage Figure 9. Off–State Cathode Current
versus Ambient Temperature
Figure 10. Dynamic Impedance
versus Frequency Figure 11. Dynamic Impedance
versus Ambient Temperature
Figure 12. Open–Loop Voltage Gain
versus Frequency Figure 13. Spectral Noise Density
VOL
A
TL431, A, B Series
http://onsemi.com
7
Input
Output
t, TIME (µs)
Pulse
Generator
f = 100 kHz
0 8.04.0 20
0
16
2.0
3.0
12
0
1.0
5.0
0
20
40
60
80
100
120
140
1000 pF 0.01 µF 0.1 µF 1.0 µF 10 µF
CL, LOAD CAPACITANCE
100 pF
Figure 14. Pulse Response Figure 15. Stability Boundary Conditions
50
220 Output
Gnd
Input
Monitor
A) VKA = Vref
B) VKA = 5.0 V @ IK = 10 mA
C) VKA = 10 V @ IK = 10 mA
D) VKA = 15 V @ IK = 10 mA
D) TA = 25°C
TA = 25C
VOLTAGE SWING (V)
IK, CATHODE CURRENT (mA)
A
B
C
D
B
A
Stable
Stable
Figure 16. Test Circuit For Curve A
of Stability Boundary Conditions Figure 17. Test Circuit For Curves B, C, And D
of Stability Boundary Conditions
V+
IK
150
IK
V+
150
CL
10 k
CL
Figure 18. Shunt Regulator Figure 19. High Current Shunt Regulator
V+ Vout
R1
V+ Vout
R1
R2
R2
Vout 1R1
R2Vref Vout 1R1
R2Vref
TYPICAL APPLICATIONS
TL431, A, B Series
http://onsemi.com
8
Figure 20. Output Control for a
Three–Terminal Fixed Regulator Figure 21. Series Pass Regulator
V+ Vout
R1
R2
Out
In
MC7805
V+ Vout
R2
Common
R1
Vout 1R1
R2Vref
Vout min Vref 5.0V
Vout 1R1
R2Vref
Vout min Vref Vbe
Figure 22. Constant Current Source Figure 23. Constant Current Sink
V+
RCL Iout
V+
RS
ISink Vref
RS
Iout Vref
RCL
Isink
Figure 24. TRIAC Crowbar Figure 25. SRC Crowbar
Vout
V+
R2
V+ Vout
R1
R2
R1
Vout(trip) 1R1
R2Vref
Vout(trip) 1R1
R2Vref
TL431, A, B Series
http://onsemi.com
9
Figure 26. Voltage Monitor Figure 27. Single–Supply Comparator with
Temperature–Compensated Threshold
Vth = Vref
V+
Vout
Vin
R1 R3
V+ Vout
R2 R4
l
L.E.D. indicator is `on' when V+ is between the
upper and lower limits.
LowerLimit 1R1
R2Vref
UpperLimit 1R3
R4Vref
Vin Vout
< Vref V+
> Vref ≈2.0 V
Figure 28. Linear Ohmmeter Figure 29. Simple 400 mW Phono Amplifier
*Thermalloy
*THM 6024
*Heatsink on
*LP Package
*
Tl = 330 to 8.0 Ω
8.0 Ω
+
-
LM11
2.0 mA
25 V
25 V
-5.0 V
Vout
Range
V
1.0 MΩ
V
100 kΩ
V
V
1.0 kΩ
RX
5.0 M
1%
500 k
1%
50 k
1%
5.0 k
1%
47 k
Tone
0.05 µF
470 µF
Volume
1N5305
1.0 µF
TI
360 k
330
56 k 10 k 25 k
38 V
+
10 kΩ
10 k
Calibrate
RxVout
V Range
TL431, A, B Series
http://onsemi.com
10
Figure 30. High Efficiency Step–Down Switching Converter
150 H @ 2.0 A
1N5823
0.01µF
+
470 µF
51 k
0.1 µF
+2200 µF
4.7 k
Vin = 10 V to 20 V TIP115
MPSA20
1.0 k
4.7 k
4.7 k
102.2 k
100 k
Vout = 5.0 V
Iout = 1.0 A
Test Conditions Results
Line Regulation Vin = 10 V to 20 V, Io = 1.0 A 53 mV (1.1%)
Load Regulation Vin = 15 V, Io = 0 A to 1.0 A 25 mV (0.5%)
Output Ripple Vin = 10 V, Io = 1.0 A 50 mVpp P.A.R.D.
Output Ripple Vin = 20 V, Io = 1.0 A 100 mVpp P.A.R.D.
Efficiency Vin = 15 V, Io = 1.0 A 82%
TL431, A, B Series
http://onsemi.com
11
APPLICATIONS INFORMATION
The TL431 is a programmable precision reference which
is used in a variety of ways. It serves as a reference voltage
in circuits where a non–standard reference voltage is
needed. Other uses include feedback control for driving an
optocoupler in power supplies, voltage monitor, constant
current source, constant current sink and series pass
regulator. In each of these applications, it is critical to
maintain stability of the device at various operating currents
and load capacitances. In some cases the circuit designer can
estimate the stabilization capacitance from the stability
boundary conditions curve provided in Figure 15. However,
these typical curves only provide stability information at
specific cathode voltages and at a specific load condition.
Additional information is needed to determine the
capacitance needed to optimize phase margin or allow for
process variation.
A simplified model of the TL431 is shown in Figure 31.
When tested for stability boundaries, the load resistance is
150 . The model reference input consists of an input
transistor and a dc emitter resistance connected to the device
anode. A dependent current source, Gm, develops a current
whose amplidute is determined by the difference between
the 1.78 V internal reference voltage source and the input
transistor emitter voltage. A portion of Gm flows through
compensation capacitance, CP2. The voltage across CP2
drives the output dependent current source, Go, which is
connected across the device cathode and anode.
Model component values are:
Vref = 1.78 V
Gm = 0.3 + 2.7 exp (–IC/26 mA)
where IC is the device cathode current and Gm is in mhos
Go = 1.25 (Vcp2) µmhos.
Resistor and capacitor typical values are shown on the
model. Process tolerances are ±20% for resistors, ±10% for
capacitors, and ±40% for transconductances.
An examination of the device model reveals the location
of circuit poles and zeroes:
P1 1
2RGM CP1 1
2* 1.0 M * 20 pF 7.96 kHz
P2 1
2RP2CP2 1
2* 10 M * 0.265 pF 60 kHz
Z1 1
2RZ1CP1 1
2*15.9k*20pF500 kHz
In addition, there is an external circuit pole defined by the
load:
PL1
2RLCL
Also, the transfer dc voltage gain of the TL431 is:
GGMRGMGoRL
Example 1:
IC10mA,RL230 ,CL0.Define the transfer gain.
The DC gain is:
GGMRGMGoRL
(2.138)(1.0 M)(1.25 )(230) 615 56 dB
Loop gain G8.25 k
8.25 k 15 k 218 47 dB
The resulting transfer function Bode plot is shown in
Figure 32. The asymptotic plot may be expressed as the
following equation:
Av 615 1jf
500 kHz
1jf
8.0 kHz1jf
60 kHz
The Bode plot shows a unity gain crossover frequency of
approximately 600 kHz. The phase margin, calculated from
the equation, would be 55.9 degrees. This model matches the
Open–Loop Bode Plot of Figure 12. The total loop would
have a unity gain frequency of about 300 kHz with a phase
margin of about 44 degrees.
TL431, A, B Series
http://onsemi.com
12
Figure 31. Simplified TL431 Device Model
+
RL
VCC
-
CL
15 k
9.0 F
Input
8.25 k
3
Cathode
500 k
Vref
1.78 V
Rref
16
GM
Anode 2
RGM
1.0 M
Ref
1
Go
1.0 mho
CP2
0.265 pF
RP2
10 M
RZ1
15.9 k
CP1
20 pF
f, FREQUENCY (Hz)
102
101
-20
30
20
60
0
Av, OPEN-LOOP VOLTAGE GAIN (dB)
Figure 32. Example 1 Circuit Open Loop Gain Plot
TL431 OPEN-LOOP VOLTAGE GAIN VERSUS FREQUENCY
40
104
10310105106
10
-10
50
Example 2.
IC = 7.5 mA, RL = 2.2 k, CL = 0.01 F. Cathode tied to
reference input pin. An examination of the data sheet
stability boundary curve (Figure 15) shows that this value of
load capacitance and cathode current is on the boundary.
Define the transfer gain.
The DC gain is:
GGMRGMGoRL
(2.323)(1.0 M)(1.25 )(2200) 6389 76 dB
The resulting open loop Bode plot is shown in Figure 33.
The asymptotic plot may be expressed as the following
equation:
Av 615 1jf
500 kHz
1jf
8.0 kHz1jf
60 kHz 1jf
7.2 kHz
Note that the transfer function now has an extra pole
formed by the load capacitance and load resistance.
Note that the crossover frequency in this case is about
250 kHz, having a phase margin of about –46 degrees.
Therefore, instability of this circuit is likely.
f, FREQUENCY (Hz)
102
101
-20
40
20
80
0
Av, OPEN-LOOP GAIN (dB)
Figure 33. Example 2 Circuit Open Loop Gain Plot
TL431 OPEN-LOOP BODE PLOT WITH LOAD CAP
60
104
10310105
With three poles, this system is unstable. The only hope
for stabilizing this circuit is to add a zero. However , that can
only be done by adding a series resistance to the output
capacitance, which will reduce its effectiveness as a noise
filter. Therefore, practically, in reference voltage
applications, the best solution appears to be to use a smaller
value of capacitance in low noise applications or a very large
value to provide noise filtering and a dominant pole rolloff
of the system.
TL431, A, B Series
http://onsemi.com
13
LP SUFFIX
PLASTIC PACKAGE
CASE 29–11
(TO–92)
ISSUE AL
P SUFFIX
PLASTIC PACKAGE
CASE 626–05
ISSUE L
OUTLINE DIMENSIONS
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. CONTOUR OF PACKAGE BEYOND DIMENSION R
IS UNCONTROLLED.
4. LEAD DIMENSION IS UNCONTROLLED IN P AND
BEYOND DIMENSION K MINIMUM.
R
A
P
J
L
B
K
G
H
SECTION X–X
C
V
D
N
N
XX
SEATING
PLANE DIM MIN MAX MIN MAX
MILLIMETERSINCHES
A0.175 0.205 4.45 5.20
B0.170 0.210 4.32 5.33
C0.125 0.165 3.18 4.19
D0.016 0.021 0.407 0.533
G0.045 0.055 1.15 1.39
H0.095 0.105 2.42 2.66
J0.015 0.020 0.39 0.50
K0.500 --- 12.70 ---
L0.250 --- 6.35 ---
N0.080 0.105 2.04 2.66
P--- 0.100 --- 2.54
R0.115 --- 2.93 ---
V0.135 --- 3.43 ---
1
NOTES:
1. DIMENSION L TO CENTER OF LEAD WHEN
FORMED PARALLEL.
2. PACKAGE CONTOUR OPTIONAL (ROUND OR
SQUARE CORNERS).
3. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
14
58
F
NOTE 2 –A–
–B–
–T–
SEATING
PLANE
H
J
GDK
N
C
L
M
M
A
M
0.13 (0.005) B M
T
DIM MIN MAX MIN MAX
INCHESMILLIMETERS
A9.40 10.16 0.370 0.400
B6.10 6.60 0.240 0.260
C3.94 4.45 0.155 0.175
D0.38 0.51 0.015 0.020
F1.02 1.78 0.040 0.070
G2.54 BSC 0.100 BSC
H0.76 1.27 0.030 0.050
J0.20 0.30 0.008 0.012
K2.92 3.43 0.115 0.135
L7.62 BSC 0.300 BSC
M--- 10 --- 10
N0.76 1.01 0.030 0.040

TL431, A, B Series
http://onsemi.com
14
D SUFFIX
PLASTIC PACKAGE
CASE 751–07
(SOP–8)
ISSUE W
OUTLINE DIMENSIONS
DM SUFFIX
PLASTIC PACKAGE
CASE 846A–02
(MICRO–8)
ISSUE E
S
B
M
0.08 (0.003) A S
T
DIM MIN MAX MIN MAX
INCHESMILLIMETERS
A2.90 3.10 0.114 0.122
B2.90 3.10 0.114 0.122
C--- 1.10 --- 0.043
D0.25 0.40 0.010 0.016
G0.65 BSC 0.026 BSC
H0.05 0.15 0.002 0.006
J0.13 0.23 0.005 0.009
K4.75 5.05 0.187 0.199
L0.40 0.70 0.016 0.028
NOTES:
6. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
7. CONTROLLING DIMENSION: MILLIMETER.
8. DIMENSION A DOES NOT INCLUDE MOLD FLASH,
PROTRUSIONS OR GATE BURRS. MOLD FLASH,
PROTRUSIONS OR GATE BURRS SHALL NOT
EXCEED 0.15 (0.006) PER SIDE.
9. DIMENSION B DOES NOT INCLUDE INTERLEAD
FLASH OR PROTRUSION. INTERLEAD FLASH OR
PROTRUSION SHALL NOT EXCEED 0.25 (0.010)
PER SIDE.
–B–
–A–
D
K
G
PIN 1 ID
8 PL
0.038 (0.0015)
–T– SEATING
PLANE
C
HJL
SEATING
PLANE
1
4
58
N
J
X 45
K
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A AND B DO NOT INCLUDE MOLD
PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER
SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN
EXCESS OF THE D DIMENSION AT MAXIMUM
MATERIAL CONDITION.
A
BS
D
H
C
0.10 (0.004)
DIM
A
MIN MAX MIN MAX
INCHES
4.80 5.00 0.189 0.197
MILLIMETERS
B3.80 4.00 0.150 0.157
C1.35 1.75 0.053 0.069
D0.33 0.51 0.013 0.020
G1.27 BSC 0.050 BSC
H0.10 0.25 0.004 0.010
J0.19 0.25 0.007 0.010
K0.40 1.27 0.016 0.050
M0 8 0 8
N0.25 0.50 0.010 0.020
S5.80 6.20 0.228 0.244
–X–
–Y–
G
M
Y
M
0.25 (0.010)
–Z–
Y
M
0.25 (0.010) Z SXS
M

TL431, A, B Series
http://onsemi.com
15
Notes
TL431, A, B Series
http://onsemi.com
16
ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes
without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular
purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability,
including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be
validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others.
SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or
death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold
SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable
attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim
alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer.
PUBLICATION ORDERING INFORMATION
CENTRAL/SOUTH AMERICA:
Spanish Phone: 303–308–7143 (Mon–Fri 8:00am to 5:00pm MST)
Email: ONlit–spanish@hibbertco.com
Toll–Free from Mexico: Dial 01–800–288–2872 for Access –
then Dial 866–297–9322
ASIA/PACIFIC: LDC for ON Semiconductor – Asia Support
Phone: 303–675–2121 (Tue–Fri 9:00am to 1:00pm, Hong Kong Time)
Toll Free from Hong Kong & Singapore:
001–800–4422–3781
Email: ONlit–asia@hibbertco.com
JAPAN: ON Semiconductor, Japan Customer Focus Center
4–32–1 Nishi–Gotanda, Shinagawa–ku, Tokyo, Japan 141–0031
Phone: 81–3–5740–2700
Email: r14525@onsemi.com
ON Semiconductor Website: http://onsemi.com
For additional information, please contact your local
Sales Representative.
TL431/D
NORTH AMERICA Literature Fulfillment:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303–675–2175 or 800–344–3860 Toll Free USA/Canada
Fax: 303–675–2176 or 800–344–3867 Toll Free USA/Canada
Email: ONlit@hibbertco.com
Fax Response Line: 303–675–2167 or 800–344–3810 Toll Free USA/Canada
N. American Technical Support: 800–282–9855 Toll Free USA/Canada
EUROPE: LDC for ON Semiconductor – European Support
German Phone: (+1) 303–308–7140 (Mon–Fri 2:30pm to 7:00pm CET)
Email: ONlit–german@hibbertco.com
French Phone: (+1) 303–308–7141 (Mon–Fri 2:00pm to 7:00pm CET)
Email: ONlit–french@hibbertco.com
English Phone: (+1) 303–308–7142 (Mon–Fri 12:00pm to 5:00pm GMT)
Email: ONlit@hibbertco.com
EUROPEAN TOLL–FREE ACCESS*: 00–800–4422–3781
*Available from Germany, France, Italy, UK, Ireland